MA5600 Multi-Service Access Module Operation and Maintenance ISSUE 1.0
Fixed Network Curriculum Development Section
Objectives
Upon completion of this course, you will be able to:
Grasp the basic knowledge of command line
Grasp the basic system configuration
Grasp the basic service and function configuration
Contents
1 Introduction to Command Line Operations 2 Basic System Configuration 3 Port Configuration
4 VLAN Service Configuration
Command Line Basis return Login via serial port or TELNET
Ordinary user mode MA5600
quit
enable disable
Privilege user mode MA5600 #
Configure quit
Global configuration mode MA5600(config)#
ospf
OSPF mode MA5600(config-ospf)#
rip RIP mode MA5600(config-rip)#
interface interface configuration mode MA5600(config-if-…)# MA5600(config-if…)# BTV
test
BTV mode MA5600(config-btv)#
TEST mode MA5600(config-test)#
diagnose Diagnose mode
MA5600 command line mode
MA5600(config-diagnose)#
Command Line Basis Command line help
By entering “?” ,
you can get list of commands with a brief
description under any command mode
MA5600#display? Key word matching MA5600#conf ---- MA5600#configure Chinese/English language switching MA5600#Switch language mode Access history commands
Access the previous history command: "Ctrl +P"
Access the next history command: "Ctrl +N"
Contents
1 Introduction to Command Line Operations 2 Basic System Configuration 3 Port Configuration
4 VLAN Service Configuration
Setting up Configuration Environment
MA5600 control console provides two configuration modes:
Setting up local configuration environment via the Console Local maintenance
Setting up configuration environment via Telnet Local and remote maintenance
In-band Telnet: Occupying service channels
Out-band Telnet: Occupying no service channel
Setting up Configuration Environment
Setting up a local configuration environment via the Console
Connect the computer serial port with the MA5300 Console via a standard RS232 serial cable, then configure hyper terminal in Windows or other operation systems. CON ETH MON
A D E F
SCU RS232 serial port cable PC
MA5600
Setting up Configuration Environment
Open the hyper terminal
Open-Program-Accessories-
Communications-Hyper terminal: Double click
Setting the HyperTerminal parameters
Enter the name:
MA5600（The name can be defined by the user ）
Connection use:
Directly connect to Serial port 1 (depending on actual conditions)
Port setting:
9600bit/s, 8 data bits, no parity check 1 suspension bit, no flow control
Terminal type:
VT100 or automatic test
Setting up Configuration Environment Setting up Configuration Environment via Telnet CON ETH MON
A D E F
workstation LAN
SCU
MA5600
ETH
server
workstation
Telnet Terminal
LAN local Telnet mode
Setting up Configuration Environment
workstation
Local router
LAN
Telnet terminal
WAN
CON ETH MON
A D E F
SCU
MA5600
LAN
WAN remote Telnet configuration mode Remote router workstation
Setting up Configuration Environment
User login
Via the Console
After correctly connecting the hyper terminal, press Enter key according to the prompt to enter the configuration environment
Via Telnet
According to the prompt, enter correct user name and password to enter the configuration environment
Basic Maintenance Operations
Out-band NM configuration
MA5300(config)#interface meth 0 Enter the external network interface port mode.
MA5300(config-if-meth0)#ip address 10.71.53.2 255.255.255.0 Configure the IP address of the external network interface
MA5300(config-if-meth0)#undo shutdown
Activate the external network interface
In-band NM Configuration Example Upstream 0
A
0
S
D
M E B F
FE0/7/0
7
7
SCU
MA5600
HAB
MA5200
HRB
Port ethernet 0/7/0 on the MA5600’s SCU board is connected to port 0 on the MA5200’s HAB board. The IP address of the MA5600 inband NMS is 10.10.20.2/24. The NMS VLAN ID is 1000. The IP address of the NMS is 10.10.21.1/24 The IP address of the MA5200’s VT interface is 10.10.20.254/24. The IP address of port 0 of the MA5200 HRB board is 10.10.40.1/30.
Basic Maintenance Operations In-band NM configuration
MA5600(config)#vlan 1000 mux
Add NM VLAN
MA5600(config)#interface vlan-if 1000 Enter the Vlan-interface 1000 configuration mode .
MA5600(config-if-vlanif1000)#ip address 10.10.20.2 255.255.255.0 Configure the equipment with a management address, which should be configured on vlan virtual interface 1000 .
MA5600(config)#port vlan 1000 0/7 0 Add the upstream port
Basic Maintenance Operations SNMP network management configuration
MA5600(config)# snmp-agent community read public
MA5600(config)# snmp-agent community write private Set the community name and access authority
MA5600(config)# snmp-agent trap enable Enable sending Trap
Basic Maintenance Operations
MA5600(config)#snmp-agent
target-host
trap
address
10.10.21.1 securityname private Set Trap destination address.
MA5600(config)#snmp-agent trap source vlanif 1000 Specify IP address of the inband NMS as the Trap source address.
MA5600(config)#route-static 10.10.41.1 30 10.10.20.254 Configure the equipment with a static route.
MA5600(config)#save
Basic Maintenance Operations
Operation terminal configuration Adding a User
MA5600#terminal user name
Deleting a User
MA5600#undo terminal user name
Modifying user level
MA5600#terminal user level
Modifying user password
MA5600#terminal user password
Modifying number re-entries
MA5600#terminal user reenter
Viewing User Information
MA5600#display terminal user
Basic Maintenance Operations
Board Management
Query a Board
MA5600#display board 0 MA5600#display board 0/2
Add a board(ADEF)
MA5600(config)#board add 0/1 ADE
Confirm a Board
MA5600(config)#board confirm 0
Delete a board
MA5600(config)#board delete 0/2
Reset a Board
MA5600(config)#board reset 0/1
Basic Maintenance Operations
Equipment management
Reset the system
MA5600(config)#reboot system
Show CPU Occupancy Ratio MA5600>display cpu 0/7
Display the system time
Set the system time
MA5600> display time
MA5600#time HH:MM:SS YYYY/MM/DD
Display the system version
Setting hostname
MA5600(config)#display version 0/7
MA5600(config)#sysname MA5600
System Management Configuration Configure File Management
Query the initial configuration of the MA5300 intelligent IP integrated access equipment
MA5600#display saved-configuration
Query the current configuration of the MA5300 intelligent IP integrated access equipment
MA5600#display current-configuration
query the configuration commands of fault restoration.
MA5600#display unresumed-configuration
Save the current configuration
MA5600#save
Erase the configuration files in the Flash
MA5600#erase
flash data
ADSL Port Configuration
To set the VPI/VCI of a port, run the command service-port.
MA5600(config)#service-port vlan 2 adsl 0/2/1 vpi 0 vci 35 rxcttr 0 tx-cttr 0
To add multiple virtual ports to a VLAN at a time, run the command multi-service-port. MA5600(config)#multi-service-port 3 adsl 0/2 3-10 rx-cttr 0 txcttr 0 (vlan-id 3, board 0/2 ,port range 3/10 )
Unblocking Adsl port
MA5600(config-if-adsl-0/2)#undo block all
Contents
1 Introduction to Command Line Operations 2 Basic System Configuration 3 Port Configuration
4 VLAN Service Configuration
ADSL Port Configuration CON
ADEF SPLT
ETH MON
SCU
MA5600
MODEM
PC
ADSL Port Configuration
Entering ADSL board configuration mode
MA5600(config)#interface adsl 0/5 Add an ADSL2+ line profile
MA5600(config)#adsl line-profile add huawei …
Activate port 0 on the ADSL board with line-profile above:
MA5600(config-if-adsl-0/5)#activate 0 huawei
Resetting ADSL Chipset
MA5300(config-if-adsl-0/2)#chipset reset 1
ADSL Port Configuration
Through the bit allocation information, you can get to know the
number of bits carried by every ADSL2+ tone (totally 512 tones), and analyze the performance of the line. MA5600(config-if-adsl-0/2)#display line bit-allocation 61 Upstream bits per frame: 312 Downstream bits per frame: 5616
0 0 …… 6 6 ****** 7 9 ********* 8 10 **********
9 10 11 12 13
11 12 12 13 14
*********** ************ ************ ************* **************
14 14 ************** 15 14 ************** …… 31 6 ****** ……
ADSL Port Configuration
Adding an ADSL Line Alarm Profile
MA5600(config)#adsl alarm-profile add 3 (Refer to operation manual to see more detail)
Bind alarm profile 1 with all ports of the ADSL2+ board
residing in slot 10. MA5600(config-if-adsl-0/10)#alarm-config all 1
Deleting an ADSL Line Alarm Profile
MA5600(config)#adsl alarm-profile delete 3
Querying ADSL line alarm profile information MA5600(config)#display adsl alarm-profile 3
ADSL Port Configuration
Querying ADSL Port Information
MA5600(config)#display service-port port 0/10/1
Viewing line parameters of a port MA5600(config-if-adsl-0/2)#display parameter 2
view the statistics collected on an ADSL2+ port within the past 15 minutes or 24 hours, or all available performance statistics . MA5600(config-if-adsl-0/2)#display statistics performance 61
historic-15minutes 1
SHDSL Port Configuration CON
SHEA
ETH MON
SCU
MA5600
MODEM
SHDSL Port Configuration
Add an SHDSL line profile, and number it as 3
MA5600(config)#shdsl line-profile add 3
When operating in blocked state, an SHDSL port cannot transmit data, and any operation on the port is prohibited. To operate the port, you need to unblock the port first. MA5600(config-if-shdsl-0/1)#undo block all
Activate all ports on the board residing in slot 4 using profile 3.
MA5600(config-if-shl-0/3)# activate all 3
SHDSL Port Configuration
Adding an SHDSL Line Alarm Profile
MA5600(config)#shdsl alarm-profile add 2
Bind alarm profile 2 with all ports of the SHDSL board residing in slot 3. MA5600(config-if-shdsl-0/3)#alarm-config all 2
Deleting an SHDSL Line Alarm Profile
MA5600(config)#shdsl alarm-profile delete 2
Querying SHDSL line alarm profile information MA5600(config)#display shdsl alarm-profile 2
SHDSL Port Configuration
view the brief information on a port
MA5600(config-if-shl-0/3)#display port state 0 -------------------------------------------------------------------Port Running Control Line ID Status
Alarm Running
Config
Bind
Status Profile Profile Operation Operation Status
-------------------------------------------------------------------0 Activating Active
1
1
Normal
None
Normal
-------------------------------------------------------------------MA5600(config-if-shl-0/3)#display line state 2 MA5600(config-if-shl-0/3)#display statistics performance 2 current
Ethernet Port Configuration
Set duplex mode of an Ethernet port
MA5600(config-if-scu-0/7)#duplex all full
Set the bit rate of an Ethernet port MA5600(config-if-scu-0/7)#speed all 1000m
Set an Ethernet port’s network cable type MA5600(config-if-scu-0/7)#mdi all auto
Ethernet Port Configuration
Enable/Disable a Port’s Traffic Control Function MA5600(config-if-scu-0/7)#flow-control all
Enable/Disable Traffic Suppression
MA5600(config-if-scu-0/7)#traffic-suppress all broadcast value 1
Configure a Port's MAC Address Learning Attribute MA5600(config)#mac-address max-mac-count adsl 0/10/1 vpi 0
vci 35 10
Ethernet Port Configuration
Enable/Disable Port Aggregation
MA5600(config-if-scu-0/7)#link-aggregation 0-1 ingress MA5600(config-if-scu-0/7)#display link-aggregation -----------------------------------------------
Master port Sub-ports
Mode
----------------------------------------------0
1
ingress
-----------------------------------------------
Ethernet Port Configuration
View the configuration of an Ethernet port
MA5600(config-if-scu-0/7)#display port state all -------------------------------------------------------------------Port Port Optic Native MDI Speed Duplex Flow- Active Link
Type Status VLAN
(Mbps)
Control State
-------------------------------------------------------------------0 GE absence
1
-
1000
full
on
active offline
1 GE absence
1
-
1000
full
on
active offline
--------------------------------------------------------------------
VLAN Service Configuration
The MA5600 supports diverse VLAN applications, including:
Standard VLAN Smart VLAN MUX VLAN
Super VLAN QinQ VLAN Stacking VLAN
Contents
1 Introduction to Command Line Operations 2 Basic System Configuration 3 Port Configuration
4 VLAN Service Configuration
Standard VLAN Configuration Example IP netw ork
To establish the above connections, do as follows: A
Add VLAN 9
D E
Run the command port vlan on
F
0/7/0 0/7/1
MA5600_A
to
add
a
port
on
MA5600_B and a port on MA5600_A
SC U
M A5600-A A
to a standard VLAN.
D E F
0/7/0 0/7/1
MA5600-B
SC U
Standard VLAN Configuration
Standard VLAN configuration involves:
1.Creating/Deleting a standard VLAN MA5600(config)#vlan 9 standard 2.Adding/Deleting a port to/from a standard VLAN MA5600(config)#port vlan 9 { frame/slot<3,4>|to }:0/7 { portlist<1,256> }:0 MA5600(config)#port vlan 9 { frame/slot<3,4>|to }:0/7 { portlist<1,256> }:1
Standard VLAN ServiceConfiguration
3.Displaying the information on a standard VLAN
MA5600(config)#display vlan 9 VLAN ID: 9 VLAN attribute: standard Standard port number: 2 -------------------------F/ S/ P
State
-------------------------0/ 7/ 0
down
0/ 7/ 1
down
--------------------------
Smart VLAN Service Configuration
The Smart VLAN configuration
Upper
involves:
network
1.Adding/Deleting a Smart VLAN 2.Adding/Deleting a port to/from a Smart VLAN 3.Displaying the information on a
A D E F
Smart VLAN
CON ETH MON
A D E F
ADSL link configuration MA5600 User
User
User…………………...User
vlan 20
Smart VLAN Service Configuration
Create a Smart VLAN.
MA5600(config)#vlan { smart|vlanid<1,4000> |attrib}:20 {vlantype|to }:smart
Add the upstream port
MA5600(config)#port vlan 20 0/7 0
Configure multicast PVCs.
MA5600(config)#vlan smart 20 { vpi }:vpi 0 vci 35
Smart VLAN Service Configuration
Add port 1 on the ADSL board residing in slot 0/12 to VLAN
20. MA5600(config)#service-port vlan 20 adsl 0/12/1 vpi 0 vci 35 rx-cttr 2 Add port 0-31on the ADSL board residing in slot 0/0 to VLAN
20 MA5600(config)# multi-service-port vlan 20 adsl 0/0 0-31 rxcttr 2 tx-cttr 2 After the above configuration, the PCs can visit Internet but can not ping each other.
MUX VLAN Configuration
The MUX VLAN configuration involves:
1.Creating/Deleting a MUX VLAN 2.Adding/Deleting a port to/from a MUX VLAN 3.Displaying the information on a MUX VLAN
ADSL link configuration
MUX VLAN Configuration
Create a MUX VLAN. MA5600(config)#vlan { smart|vlanid<1,4000> }:10 { mux|standard|smart|to }:mux
Add upstream port
MA5600(config)#port vlan 10 0/7 0 Add/Delete a service port to/from a MUX VLAN
MA5600(config)# service-port vlan 10 adsl 0/1/0 vpi 0 rx-cttr 0 tx-cttr 0
MUX VLAN Configuration
Add Multiple Ports to Different MUX VLAN
Add all ADSL and SHDSL ports to MUX VLANs, with the first
port corresponding to VLAN 2. MA5600(config)#multi-service-port from-vlan 2 board 0-15 vpi 0 vci 35 rx-cttr 2 tx-cttr 2
