Kromrey Converter Plans r1 - DMR10

Kromrey Converter Plans By D.M.Rogers

Full scale plans for the replication of John Bedini’s prototype of a Ferromagnetic Electric Generator invented by Raymond Kromrey. Release 1.0

1

Written by Dave Michael Rogers

Sponsored by Richard and Kate Lines Courtiestown Marine Ltd. www.courtiestown.co.uk and The OTG-List internet group http://tech.groups.yahoo.com/group/OTG-LIST/

Acknowledgements Raymond Kromrey John C Bedini Clive Sinclair Members of the OTG-List Jason, Merv, Tom of The Anvil Forge Copyright © 2010 DMR, Dave Michael Rogers, All rights reserved.

Disclaimer No liability is accepted for any injury or ill effect caused by the construction or operation of such a device. Your safety is your responsibility. NO CLAIMS ARE MADE AS TO THE PERFORMANCE OF THIS DEVICE.

2

CONTENTS

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.

Introduction Basic list of required materials. Exploded view of Kromrey Converter Drw #1 - PLATE A Drw #2 - PLATE B Drw #3 - PLATE C Drw #4 - PLATE D Drw #5 Stator Shaft & Slip Ring Assembly Drw #6 Aluminium Support Columns Drw #7 Magnet Stack Adjustable Iron Pole Drw #8 Armature design Drw #9 The Magnet Stack and pole boots Drw #10 Commutator Brush Assembly

3

Kromrey Converter An electrical generator

Original drawing from Raymond Kromrey’s US Patent.

These plans have been drawn up for a first time build of a device seen only in pictures from the internet and on DVD from the video production Energy from the Vacuum part 10, and discussions with Tom Childs and John Koorn, who have both seen John Bedini’s Kromrey up close. As such the dimensions have been based around the use of a standard size magnet known to be used by John Bedini, and all other measurements derived and calculated by graphical means from photos and screenshots. Some of the dimensions have been verified as accurate by disclosures made by John Bedini.

4

The materials specified in these plans MUST be adhered to. NO SUBSTITUTIONS.

BASIC LIST OF REQUIRED MATERIALS Description 1

2 3 4 5 6 7 8 9 10 11 12 13

Ceramic 3/8” x 15/8” x 7/8” Barium Ferrite Magnet Block, Magnetized through thickness. 6mm Aluminium Plate

Quantity 40

Aluminium Rod 25mm dia 8mm Stainless Steel 316 rod Copper Tube 15mm 6mm round Carbon Copper Brushes

4 x 215mm rounds 4x Tba 30mm 2

95mm of 25mm round Iron bar

2

M6 stainless steel Allen Bolts + Washers Bearings 16mm OD M6 stainless steel nuts 24volt Motor

8 2 8 1

5

Exploded View of Kromrey Converter

NOT TO SCALE Drawn by Dave Michael Rogers

6

A

Drw #1 - PLATE A.

• • • • •

6mm Aluminium plate 211mm Diameter Centre hole to be cut to bearing size OD, 16mm. All shaded holes are 9.5mm and countersunk. All blue tinted holes are 13mm. 7

B

Drw #2 - PLATE B.

6mm Aluminium plate. 211mm Diameter. Centre hole to be cut to 15mm. All shaded holes are 5.5mm and threaded to take M6 SS grubs. • All tinted holes are 6mm.

• • • •

8

C

Drw #3 - PLATE C.

• • • • • 9

6mm Aluminium plate 211mm Diameter Centre hole to be cut to bearing size, 16mm. All shaded holes are 5.5mm and threaded for M6 grubs. All tinted holes are 6mm.

D

.

Drw #4 - PLATE D.

• • • • • 10

6mm Aluminium plate 211mm Diameter Centre hole plugged. All shaded holes are 9.5m and countrsunk All blue tinted holes are 13mm and countersunk.

8mm OD Stainless Steel 316 Insulated hole through slip ring assembly.

47mm

Cross section 15mm OD

Copper Slip ring 115.6mm

123mm

Epoxy plastic

30mm

Stator Coil Bobbin size

< Bearing width Hard rubber washer

Bearing bore size

Drw #5 Stator Shaft & Slip Ring Assembly. The stainless steel used for the shaft MUST be NONMAGNETIC. This is most important.

11

M6 Stainless Steel Allen Bolt 10mm

25mm OD 115.6mm

25mm

M6 Stainless Steel Allen

Drw #6 Aluminium Support Columns. Minimum of 4 support columns are required, but provisions for 8 support columns are apparent on the original Kromrey replication by John Bedini.

12

7mm

17mm

31mm

2mm

3.5mm 25mm

55mm

r 45.1mm

21.4mm

53.5mm

Drw #7 Magnet Stack Adjustable Iron Pole

33mm r 45mm

25mm Plan elevation

SOFT IRON

Drw #8 Armature design 6mm

15mm Side elevation 35mm 13

115.6mm

147mm

Adjustable Iron Pole pieces

1.4mm

9 x Ceramic grade 8 3/8” x 15/8” x 7/8” Magnets.

45.5mm

M6 Stainless Steel studding grub screws. 4 needed per magnet stack, max of 32 could be needed.

Drw #9 The Magnet Stack and pole boots. Kromrey Side Elevation

14

Cotter pin

25mm OD

M6 Bolt

25mm

6mm brushes and springs

Moulded plastic Brush housing.

Drw #10 Commutator Brush Assembly.

15

Part 1 END

Please visit your Kromrey support group for a photographic record and technical support.

16