WARNING: Use this CARD as Reference only (Training aid)! SEPB201301 Read the Operations Manual before operating! Service Technology Development Group Customer Support Division EMMS: EMM S: Equipment Management Monitoring System
<
- Moves Moves Left Left
>
- Moves Moves Right Right - Select Selectss Mode - Cancel Cancelss Mode - Maintenance Mode Functions Functions -
> Ignition key must switched to the "ON" position and the machine must be in the "PARK" mode in order to allow access to the functions on the monitor display. When using using the “Select Mode” to access menu, the switch must be held in the <> position at least 3 to 4 seconds in order to access menu functions in the Operator Mode.
< No. 1 2 3 4 5 6 7 8 9 10 11
Normal Monit or Display Normal Monitor Monitor Display Key Key "ON" "ON"
<
Scroll through the menu
>
or
01:ENG OIL 02:ENG :ENG FIL FILT 03:FU :FUEL FILT 04:HYD :HYD FILT 05:C 05:COR ORR R RES RES 06:BYP :BYPS S FI FILT 07:DAMP OIL 08:FNL OIL 09:HYD OIL 10:P 10:POW OWL L Oil Oil 11:PO 11:POWL WL FILT FILT
12 12:H 12:HST ST FI FILT select
<
E01 -Only action code is displayed E02 -Only action code is displayed E03
YES or NO
>
The maintenance interval is re-set and the monitor display returns to the maintenance item chosen.
YES
<
enter
NO
>
eenter nter
No action is taken.
NO
>
enter
The maintenance item is not re-set and the monitor display returns to the maintenance item c hosen.
- PM Clinic Clinic Functions Functions -
An Action Code will automatically be displayed when a serious fault occurs in the system. There are 4 Action Codes.
Maintenance item Engine oil Eng Engine ine oil filt ilter Fuel filt filter er Hydr ydraulic ulic oil filt filte er Corr Corros osio ion n resi resist stor or Byp Bypass filt ilter Damper oil Final drive oil Hydraulic oil Powe Powerr trai train n oil oil Power Power train train oil oil filte filter r HST charge filter (HST spec)
>
<
- Error Code Functions -
E02 -code ONLY is displayed
>
-Caution lamp flashes -Caution buzzer sounds Contents of Fault:
<
Remedy:
•Stop engine and restart machine •Stop ! Call your Komatsu dealer
E03 -Action code is displayed
If a problem is detected in the operating systems, the monitor read-out will display one of two indications. These would be a display with the words “!!ERROR CODE!! This is usually followed by an audible warning as well as a separate indication elsewhere. The other display would be the actual “FAULT CODE” display listing for the system with a problem. This is usually indicated by a six digit display specifically for the system with the problem. The monitor is capable of sorting 20 items, each will be displayed automatically every two seconds in the order of occurrence.
-Caution lamp flashes -Caution buzzer sounds
- User Adjust Functions -
-HST Speed limit = 50% km/h Contents of Fault:
>
<
Remedy:
•Move to a safe location and shut machine down immediately
E04 -Action code is displayed -Caution lamp flashes -Caution buzzer sounds -HST STOPS ! Park BRAKE Locks! Contents of Fault:
Scroll through the menu
Adjustment item Brightness of LCD Brightness of display Contrast of display
> >
or
Decrease intensity
Increase intensity
<
After selecting desired brightness or contrast The mode is now set, and can be changed
Unit % % %
ERROR CODE TABLE (1/3)
ERROR CODE TABLE (2/3)
ERROR CODE TABLE (3/3)
WARNING: Use this CARD as Reference only (Training aid)! Read the Operations Manual before operating! EMMS: Equipment Management Monitoring System
<
- Moves Left
>
- Moves Right - Selects Mode - Cancels Mode
Ignition key must switched to the "ON" position and the machine must be in the "PARK" mode in order to allow access to the functions on the monitor display when in the Service Mode.
Normal Normal Monitor Monitor Display Display Key Key "ON" "ON"
No.
To access Service Mode, hold toggle switch in “Down" position together with the “Select Mode” switch for 6 to 8 seconds. Down w/out Key = SMR read.
Under EMMS Monitor switch
1 01: ENG OI L 2 02: ENG FI LT 3 03: FUEL FI LT 4 04: HYD FI LT 5 05: CORR RES 6 06: BYPS FI LT 7 07: DAMP OI L 8 08: FNL OI L 9 09: HYD OI L 10 10: POW L OI L 11 11: POW L FI LT 12 12: HST FI LT
Mai ntenance i tem Engi ne oi l Engi ne oi l f i l ter Fuel f i l ter Hydraul i c oi l f i l ter Corrosi on resi stor Bypass f i l ter Damper oi l Fi nal dri ve oi l Hydraul i c oi l Power trai n oi l Power trai n oi l f i l t er HST charge f i l ter (HST speci f i
< Held “Down”
Scroll through the menu
Repl acement i nter val ti me 1st ti me nd ti me and af te (Cannot be changed) (Can be changed) 0500h 0500h 0500h 0500h 0500h 0500h 2000h 2000h ? ? ? ? ? ? 1000h 1000h 2000h 2000h ? ? ? ? 2000 2000
>
or
To change time interval “UP” (increases numeric value) “DOWN” (
You have two options in this mode: 1. Re-set the maintenance time interval. 2. Cancel systems operation
To display all codes, use Left, Right feature. Up to 20 codes can be recorded and displayed. Codes are stored in order of oldest to the newest. A flashing code means the fault is currently happening. Erase all codes in system
Previous code (Left)
<
>
Next code (Right)
“UP” (erases codes) If a code cannot be erased, this is an indication the electrical problem has not been repaired and is continuing to re-occur. Exit system
No Action
To display all codes, use Left, Right feature. Up to 6 codes can be recorded and displayed.
“DOWN” (erases codes)
CAUTION!
By using the “Shift-up” and “Shift-down” buttons you can scroll through the numbers to enter the code for the item you select. By using the < > feature you can position the cursor on a digit.
Adjustment item INP TEL NO. M-CODE BODY TYPE BRAKE N-SET SMR SET S/T H.L-SET S/T H.R-SET S/T N-SET S/T M.L-SET S/T M.R-SET PUMP AJST F PUMP AJST R PU F-UP MAP PU R-UP MAP PU F-HF MAP PU R-HF MAP BRAKE END ENG HI-SET DECEL HI>LO T HROTTLE LO STALL CHECK SHIFT LIMIT
