Isometric Drawing Extraction

PDS ISOGEN Reference Guide August 1999 DEA5040A0 For PDS version 06.04.00.**

This document replaces DEA504092

Warranties and Liabilities All warranties given by Intergraph Corporation about equipment or software are set forth in your purchase contract, and nothing stated in, or implied by, this document or its contents shall be considered or deemed a modification or amendment of such warranties. The information and the software discussed in this document are subject to change without notice and should not be considered commitments by Intergraph Corporation. Intergraph Corporation assumes no responsibility for any error that may appear in this document. The software discussed in this document is furnished under a license and may be used or copied only in accordance with the terms of this license. No responsibility is assumed by Intergraph for the use or reliability of software on equipment that is not supplied by Intergraph or its affiliated companies.

Trademarks Intergraph is a trademark of Intergraph Corporation. MicroStation is a trademark of Bentley Systems Inc., an Intergraph affiliate.

Copyright  1999 Intergraph Corporation All Rights Reserved Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license agreement; contains confidential and proprietary information of Intergraph and/or third parties which is protected by copyright and trade secret law and may not be provided or otherwise made available without proper authorization. RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by the government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of The Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 or subparagraphs (c) (1) and (2) of Commercial Computer Software — Restricted Rights at 48 CFR 52.227-19, as applicable. Unpublished — rights reserved under the copyright laws of the United States. Intergraph Corporation Huntsville, Alabama 35894-0001

If You Need Assistance Intergraph Online Our web site brings you fast, convenient, up-to-the-minute information about Intergraph’s products, services, and direction. Our web address is: http://www.intergraph.com

Telephone Support All Intergraph products are delivered with a 30-day warranty for full coverage of physical media. In the United States, call Intergraph’s standard support number at 1-800-633-7248 from 7:00 AM to 7:00 PM CST, Monday through Friday, except holidays. If you are outside of the United States, please call your local Intergraph office. The most up-to-date list of international offices and distributors is available on the web at http://www.intergraph.com. Please have the following information available when you call: The product’s serial number. This can be found on the license agreement or by using the About command in the product. Your name and telephone number. The product’s name. Your CPIN number and service number. A brief description of the problem.

Intergraph Directory The following numbers are only valid in the United States unless otherwise indicated. If you are outside the United States, please call your local Intergraph office.

Intergraph General Information U.S. — 1-800-345-4856 Canada — 1-800-461-5297 All countries — 1-256-730-2000

Customer Response Center (U.S. Only) Customer Support — 1-800-633-7248 U.S. Customer Care Center — 1-888-779-3824 FAX — 1-800-239-2972

Training Registration (U.S. Only) 1-800-240-3000

Regional Sales Information (U.S. Only) 1-800-240-1000

Mailing Address Intergraph Corporation Huntsville, Alabama 35894-0001 U.S.A. You can also reach us by electronic mail at [email protected].

Educational Media Contacts We are constantly working on updates and improvements to the documents and other educational media. If you have any suggestions on where we can improve the documentation or where you think more information is needed, let us know. You can reach us by: Mail

Intergraph Corporation Manager, PBS Documentation GD3006 Huntsville, AL 35894-0001

FAX

PBS Documentation 1-256-730-3300

Electronic Mail

[email protected]

Table of Contents vii

Table of Contents

__________________________________________________________________________________________________________________________________________________

If You Need Assistance .................................................................................. Intergraph Directory ......................................................................................

iii iv

Preface .........................................................................................................................

xiii

General Conventions ............................................................................................

xv

Introduction to ISOGEN ......................................................................................

1-1

1.1

Overview of Isometric Extraction ................................................................

1-3

1.1.1 1.1.2 1.1.3

The Intergraph Interface to ISOGEN ............................................. ASCII to Binary Conversion ............................................................ ISOGEN ............................................................................................

1-3 1-4 1-4

PDS Environment .................................................................................................

2-1

2.1

PD Shell ........................................................................................................

2-2

2.1.1 2.1.2

PD_Shell Form Conventions ............................................................ Batch Processes ................................................................................

2-5 2-8

Interactive Isometric Extraction ..........................................................................

3-1

3.1

3-9

1.

2.

3.

Extraction Criteria ....................................................................................... 3.1.1 3.1.2

Model Files ........................................................................................ Pipeline Names .................................................................................

3-9 3 - 10

Iso Design File .............................................................................................. Plot Isometric Drawing ................................................................................ View Isometric Drawing .............................................................................. Conventions and Limitations ......................................................................

3 - 12 3 - 14 3 - 17 3 - 19

3.5.1 3.5.2

Extraction Conventions .................................................................... Extraction Limitations .....................................................................

3 - 19 3 - 20

Batch Software Organization ...............................................................................

4-1

4.1 4.2 4.3 4.4

The Batch Job Input File ............................................................................. Line Processing (pdsidf) ............................................................................... The ISOGEN Interface ................................................................................ ISOGEN ........................................................................................................

4-3 4-4 4-5 4-5

4.4.1

4-6

3.2 3.3 3.4 3.5

4.

Splitting the MTO neutral file (MSPLIT) .......................................

viii PDS ISOGEN Reference Guide - August 1999

4.5 4.6 4.7 4.8 4.9 4.10 5.

Generating Title Block Input (TBLOCK) .................................................... Filling in the Title Block (STIB) .................................................................. Plotting ......................................................................................................... Updating the Project Database (pdsidf) ...................................................... Making a Run Log Entry (pdsidf) ................................................................ Investigating Batch Extraction Problems .................................................

4-6 4-6 4-7 4-7 4-7 4-7

Batch Isometric Extraction ..................................................................................

5-1

5.1 5.2 5.3

5-3 5-7 5-9

Initial Setup Considerations ........................................................................ Basic Workflow for Running Batch Isometrics ........................................... Batch Isometric Generation ......................................................................... 5.3.1

Define Default Sets ..........................................................................

5 - 13

5.3.1.1 5.3.1.2 5.3.1.3 5.3.1.4

Add Default Set .................................................................. Revise Default Set ............................................................. Delete Default Set .............................................................. Copy Default Set ................................................................

5 - 15 5 - 18 5 - 20 5 - 21

Define Project Options ..................................................................... Revise Iso Area ................................................................................. List Iso Areas .................................................................................... Create Drawing ................................................................................ Revise Drawing ................................................................................. Delete Drawing ................................................................................. List Drawings ................................................................................... Utilities .............................................................................................

5 - 22 5 - 25 5 - 27 5 - 28 5 - 33 5 - 46 5 - 54 5 - 56

5.3.9.1

Bulk Load Lines .................................................................

5 - 57

Load by Area ......................................................................................................... Load by Model ....................................................................................................... Load by Line .........................................................................................................

5 - 60 5 - 62 5 - 64

5.3.9.2 5.3.9.3

Bulk Load Lines from ASCII File .......................................................... Isometric Symbol Editor ........................................................................

5 - 67 5 - 71

Entering the Iso Symbol Editor Environment .................................................... Input Area Options ............................................................................................... Assembling an Isometric Symbol ......................................................................... Creating a User-defined Symbol Library ............................................................ Using the Newly-created Symbol Library ...........................................................

5 - 72 5 - 73 5 - 76 5 - 83 5 - 84

5.3.9.4 5.3.9.5

5 - 85 5 - 86

5.3.2 5.3.3 5.3.4 5.3.5 5.3.6 5.3.7 5.3.8 5.3.9

Delete Drawing Records With Undefined Iso Type .............................. Generate FrameWorks Reference Dimension File ...............................

5.3.10 5.3.11 5.3.12 6.

Create Batch Job Input .................................................................. Schedule Batch Job ........................................................................ Reports ............................................................................................

5 - 89 5 - 100 5 - 104

Interpreting the HITS Report ..............................................................................

6-1

Table of Contents ix

6.1 6.2 6.3 6.4 6.5 6.6 6.7 7.

Example HITS Report ................................................................................. Section 1: Basic Input Data and Raw Design File Data ............................ Section 2: Design File Data Sorted by Coordinate ..................................... Section 3: Tracing Data ............................................................................... Section 4: Design File Data Sorted by Topo ............................................... Section 5: Design File Data in IDF Order ................................................... Using the HITS Report to Solve Problems .................................................

6-2 6 - 12 6 - 13 6 - 14 6 - 15 6 - 22 6 - 26

The Options File ...................................................................................................

7-1

7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 7.11 7.12 7.13 7.14 7.15 7.16 7.17 7.18 7.19 7.20 7.21 7.22 7.23 7.24 7.25 7.26 7.27 7.28 7.29 7.30 8.

File Structure ............................................................................................... ISOGEN_OPTIONS_BLOCK ...................................................................... INTERGRAPH_OPTIONS_BLOCK ........................................................... The Files Table ............................................................................................. USER_DEFINED_WELDS ......................................................................... WELD_PREFIX ........................................................................................... DETAIL_SKETCH_FACILITY ................................................................... PIPELINE_HEADER .................................................................................. ATEXT_SPECIFICATIONS ........................................................................ INGR_ATEXT_SPECIFICATIONS .......................................................... LINE_ID_DEFINITION ............................................................................ TYPE_1_LABELS ...................................................................................... TYPE_2_LABELS ...................................................................................... TYPE_3_LABELS ...................................................................................... START_POINT_NOTES ............................................................................ END_POINT_COMPONENT_LABELS ................................................... NOZZLE_NOTE ......................................................................................... SECONDARY_ORIENTATION_NOTE .................................................... DOTTED_SYMBOLOGY_CODE_LIST_VALUES ................................... NOMTO_CODE_LIST_VALUES .............................................................. SHOP_FABCAT_CODE_LIST_VALUES ................................................. OFFSHORE_FABCAT_CODE_LIST_VALUES ....................................... MOVABLE_TEXT ...................................................................................... NEW_SYMBOL_KEYS .............................................................................. GENITM_NOTE_FORMAT ...................................................................... ALTERNATE_DESCRIPTION_INDEX ................................................... USER_DEFINED_IMPLIED_ITEM_BOM .............................................. USER_DEFINED_GENERATED_ITEM_BOM ....................................... USER_DEFINED_COMPONENT_BOM .................................................. NON_DIMENSIONED_SUPPORTS ........................................................

7-2 7-4 7-6 7 - 42 7 - 45 7 - 47 7 - 48 7 - 50 7 - 56 7 - 58 7 - 59 7 - 60 7 - 63 7 - 66 7 - 68 7 - 70 7 - 72 7 - 74 7 - 75 7 - 77 7 - 78 7 - 80 7 - 81 7 - 84 7 - 85 7 - 87 7 - 89 7 - 92 7 - 95 7 - 98

User-Defined BOM / Material Control File .........................................................

8-1

8.1

Types of Material List ..................................................................................

8-2

8.1.1

Operating Requirements ..................................................................

8-4

Material List Definition (MLD) File ............................................................ User-Defined Material Control File (.bom file) ........................................... Offshore Material Category ......................................................................... Transferring Components Between Sort Groups ....................................... Generating an Optional Format for Length Output .................................. Bolt Units (size x length) .............................................................................

8-6 8-7 8-9 8-9 8 - 10 8 - 10

8.2 8.3 8.4 8.5 8.6 8.7

x

PDS ISOGEN Reference Guide - August 1999

8.8 Generating a Revised Format of the Cut List ............................................ 8.9 Welds in the Material List ........................................................................... 8.10 Style for Fabricated (Pulled) Bends Output ............................................. 8.11 Style for Material List Output .................................................................. 8.12 Positioning the Title Block ........................................................................ 8.13 MLD File Content ...................................................................................... 8.14 MLD File Format Guidelines .................................................................... 8.14.1

Style 3 Material List ....................................................................

8 - 17

Example User-defined Material List - Style 2 .......................................... Example User-defined Material List - Style 3 ..........................................

8 - 19 8 - 19

Creating Seed Files for Extraction ......................................................................

9-1

9.1 9.2

Creating an Isometric Seed File .................................................................. Creating a Plot Request File .......................................................................

9-1 9-3

9.2.1

IPLOT Plot Request Files ................................................................

9-3

Mapping Attributes to the Title Block ...............................................................

10 - 1

8.15 8.16 9.

10.

10.1 10.2 10.3 11.

12.

13.

8 - 11 8 - 13 8 - 13 8 - 13 8 - 14 8 - 14 8 - 15

SEGMENT_DATA_TABLE ..................................................................... DRAWING_DATA_TABLE ..................................................................... SHEET_DATA_TABLE ...........................................................................

10 - 3 10 - 7 10 - 12

Creating a Notes Table .......................................................................................

11 - 1

11.1

Using the isoc.note File ............................................................................

11 - 2

The MTO Neutral File Record Map ...................................................................

12 - 1

12.1 12.2 12.3 12.4

COMMON_RECORD_DATA ................................................................... COMPONENT_ATTRIBUTES ................................................................ IMPLIED_ITEMS .................................................................................... GENERATED_ITEMS .............................................................................

12 - 2 12 - 4 12 - 6 12 - 9

The PDS-to-ISOGEN Symbol Map ....................................................................

13 - 1

13.1 13.2 13.3 13.4 13.5

The PDS Item Name ................................................................................ The ISOGEN Symbol Name .................................................................... The ISOGEN Record Number ................................................................. Number of Connect Points ....................................................................... Tapped Component Name .......................................................................

13 - 1 13 - 1 13 - 2 13 - 3 13 - 3

13.5.1 13.5.2

Tapped elbows ............................................................................ Olets attached to fittings ............................................................

13 - 3 13 - 4

Tapped component record number .......................................................... PDS Valve Operator Name ...................................................................... End Prep Low and End Prep High .......................................................... Order of Table Entries .............................................................................

13 - 4 13 - 4 13 - 5 13 - 5

13.6 13.7 13.8 13.9

Table of Contents xi

14.

The Valve / Operator Table ................................................................................

14 - 1

15.

Repeatability .......................................................................................................

15 - 1

15.1 15.2 15.3 15.4 15.5

Repeatability Restrictions and Limitations ............................................ Extraction Information in the Database ................................................. Determining the Traversal Start Point .................................................. Determining Sheet Split Points ............................................................... Determining Spool Split Points ...............................................................

15 - 2 15 - 3 15 - 4 15 - 4 15 - 5

Welds ...................................................................................................................

16 - 1

Delivered weld symbols ...................................................................................... 16.1 Dotted Weld Symbols ............................................................................... 16.2 User-defined Weld Symbols ..................................................................... 16.3 Codelist Values for Standard Note 180 and 1100 .................................. 16.4 Weld Types and Mapping ........................................................................ 16.5 Offshore Fabrication Category ................................................................ 16.6 Unique Weld Numbering ......................................................................... 16.7 User-defined Weld Prefix ......................................................................... 16.8 The Weld Summary Report .....................................................................

16 - 2 16 - 2 16 - 3 16 - 3 16 - 3 16 - 4 16 - 4 16 - 4 16 - 5

16.

16.8.1 16.8.2

Weld Definition File Format ...................................................... Example WDF File .....................................................................

16 - 5 16 - 9

Welds Listed in the Bill of Materials ......................................................

16 - 10

Dimensioning and Coordinate Output ...............................................................

17 - 1

17.1 17.2

Dimensioning Features ............................................................................ Coordinate Features ................................................................................

17 - 1 17 - 3

Detail Sketch and Information Note Facility ....................................................

18 - 1

18.1 18.2

Detail Sketch Entries in the DDF ........................................................... Information Note Entries in the DDF .....................................................

18 - 2 18 - 3

Weight Display ...................................................................................................

19 - 1

19.1

Center of Gravity Calculation .................................................................

19 - 2

Isometric Presentation .......................................................................................

20 - 1

20.1 20.2 20.3 20.4 20.5 20.6 20.7 20.8 20.9 20.10

20 - 3 20 - 4 20 - 4 20 - 5 20 - 5 20 - 6 20 - 7 20 - 8 20 - 8 20 - 9

16.9 17.

18.

19.

20.

PIPELINE-ATTRIBUTES ....................................................................... PIPELINE-ATTRIBUTES-SPECIAL ..................................................... PIPELINE-ATTRIBUTES-DOTTED ...................................................... BEND/ELBOW-REPRESENTATION .................................................... FITTINGS-GENERAL ............................................................................. FITTINGS-SPECIAL ............................................................................... FITTINGS-UNDIMENSIONED-BRANCHES ....................................... MISC-ITEMS ........................................................................................... LAYER-NAMES ....................................................................................... Program Defaults ...................................................................................

xii PDS ISOGEN Reference Guide - August 1999

20.11 21.

Example Drawing Definition File .........................................................

20 - 10

Isometric Types ...................................................................................................

21 - 1

Appendix A: A.1

Warning and Error Messages .............................................................

A-3

Intergraph Interface to ISOGEN ......................................................................

A-4

A.1.1 A.1.2 A.1.3 A.2

A.3

Information Messages ............................................................................ Warning Messages ................................................................................. Error Messages ......................................................................................

A-5 A-8 A - 15

ISOGEN ..............................................................................................................

A - 22

A.2.1 A.2.2

ISOGEN message file errors ................................................................. Design File Interface Error Messages ...................................................

A - 22 A - 31

Batch Extraction Software Error Messages .....................................................

A - 32

Appendix B:

Alias ISOGEN Tables .........................................................................

B-3

Appendix C:

Example Documents ............................................................................

C-3

The Options File (#/dat/isoc.def) ........................................................................ Label Library Label Definitions ........................................................................ HITS Report (.h file) .......................................................................................... Intermediate Data File (.idf file) ....................................................................... Interface Error Log (.err file) ............................................................................. MTO Neutral File (.b# file) ................................................................................ ISOGEN Message File (.msg file) ...................................................................... ISOGEN Printed Parts File (.prt file) ............................................................... ISOGEN Component versus Sheet Number File (.sed file) ............................. ISOGEN Cut Pipe Report (.cut file) ................................................................ Title Block Table (.bit, .seg and .dwg files) .....................................................

C-4 C-9 C - 28 C - 37 C - 54 C - 57 C - 59 C - 60 C - 62 C - 63 C - 64

C.1 C.2 C.3 C.4 C.5 C.6 C.7 C.8 C.9 C.10 C.11

Appendix D: D.1 D.2

PDS Database Table Formats ............................................................

D-3

Piping Design Database Table Format ............................................................. Specification/Material Reference Database Table Format ..............................

D-4 D - 11

Appendix E:

ISOGEN SKEY Dimensions ...............................................................

E-3

Glossary .......................................................................................................................

GL - 3

Index ............................................................................................................................

IN - 3

Preface xiii

Preface

__________________________________________________________________________________________________________________________________________________

Document Purpose This document is a reference guide for Intergraph Corporation’s PD ISOGEN software package. You can use the PD ISOGENTM software to generate piping isometric drawings from 3D models created by PDS. The ISOGEN product is one part of the overall Intergraph Plant Design System. This document is designed as a reference for the PD ISOGEN software. It includes explanations and examples of the operation of all the facilities that make up the software package. Use this guide when you need to reference a specific product function.

Document Prerequisites / Audience This document is intended for both beginning and advanced users. The beginning user should: be familiar with an Intergraph workstation have Intergraph and MicroStation operating experience have PDS Piping operating experience. The advanced user should: have a good understanding of basic Windows commands and text editors knowledge of Intergraph software such as EDG and relational databases be capable of modifying the PDS 3D RDB have a good understanding of the general PDS environment.

Related Documents/Products MicroStation  32 software is required to operate in the PDS 2D Graphics software. Information about MicroStation 32 capabilities can be found in the following documents: MicroStation 32 Reference Guide MicroStation 32 User’s Guide Intergraph Corporation’s Relational Interface System (RIS)TM is required to operate PDS ISOGEN, along with a relational database management system (RDBMS) supported by RIS. Currently, these include Informix, Oracle, and Ingres. Information about RIS capabilities can be found in the following documents:

xiv PDS ISOGEN Reference Guide - August 1999

Relational Interface System (RIS) Reference Manual Relational Interface System (RIS) Operator Training Guide For more information on related aspects of the PD ISOGEN products, consult the following documents: Project Administrator Reference Guide Piping Design Graphics Reference Guide

Additional Information The following informational files are delivered with the PDS ISOGEN software in the /usr#/ip32/isogen directory. File Name

Contents

README

Describes changes and additions to the product since the last version. Lists the names and dates of the files in the current release. For a fixes release, the files which have been modified are appended to the top of the initial file to provide a history of all changes to the product. Includes Comments and Trouble Report numbers which describe what problems have been fixed. Provides special notices to the customer. Lists any exceptions made to the certification.

product.def

Lists all dependencies and related parts for the product.

Preface xv

General Conventions

__________________________________________________________________________________________________________________________________________________

This document contains many visual cues to help you understand the meaning of certain words or phrases. The use of different fonts for different types of information allows you to scan the document for key concepts or commands. Symbols help abbreviate and identify commonly used words, phrases, or groups of related information.

Typefaces Italic

Indicates a system response, which is an explanation of what the software is doing. For example, The text is placed in the viewing plane.

Bold

Indicates a command name, parameter name, or dialog box title. Command paths are shown using an arrow between command names. For example, Choose File > Open to load a new file.

Sans serif

Indicates a system prompt or message, which requires an action be taken by the user. For example, Select first segment of alignment

Bold Typewriter Indicates what you should literally type in. For example, Key in original.dat to load the ASCII file. Normal Typewriter Indicates an actual file or directory name. For example, The ASCII report is stored in the layout.rpt file.

xvi PDS ISOGEN Reference Guide - August 1999

Symbols This document uses the following symbols to represent mouse buttons and to identify special information:

Command button Data button (usually the left mouse button) Reset/reject button (usually the right mouse button) Tentative button (usually the center mouse button) Note — Important supplemental information.

Warning — Critical information that could cause the loss of data if not followed.

Technical tip or information — provides information on what the software is doing or how it processes information. Map or path — shows you how to get to a specific command or form. More information — indicates there is additional or related information. Need a hint — used with activities and labs, provides a tip or hint for doing the exercises.

Keyboard Conventions The following list outlines the abbreviations this document uses for keyboard keys and describes how to use them in combination. You can make some menu selections through the use of keyboard accelerators, which map menu selections to key combinations. ALT CTRL DEL ENTER ESC

Alternate key Control key Delete key Enter key Escape key

CTRL+z ESC,k

To hold down the Control key and press Z. To press the Escape key, then K.

Preface xvii

Terminology Click

To use a mouse or key combination to pick an item that begins an action. For example, Click Apply to save the changes.

Select

To mark an item by highlighting it with key combinations or by picking it with your cursor. Selecting does not initiate an action. After selecting an item, you click the action you want to affect the item. For example, Select the file original.dat from the list box, then click Delete to remove it from the directory. In addition, you would select items to define parameters, such as selecting toggle buttons. This also applies to selecting graphic elements from the design file. For example, Select the line string to define the graphic template.

Tentative-select

To place a tentative point on an existing graphic element in a design file. If you are using the CLIX operating system, you tentative-select by double-clicking with a mouse or pressing on a hand-held cursor. If you are using the Windows NT operating system, you tentative-select by pressing a leftbutton, right-button chord.

Double-click

To select and execute a command by clicking the mouse or hand-held cursor button twice in rapid succession. This term implies that you are clicking the data button () as part of a menu or dialog box action. For example, Double-click on the file original.dat to load it into the new surface.

Drag

To press and hold the data button () while moving the mouse or hand-held cursor.

Type

To key a character string into a text box.

Key in

To type in data and press ENTER to enter the data and execute the default action. In a dialog box, pressing TAB after keying in data will enter the data and move the cursor to the next field.

xviii PDS ISOGEN Reference Guide - August 1999

Introduction to ISOGEN 1 - 1

1. Introduction to ISOGEN

__________________________________________________________________________________________________________________________________________________

The PDS Isometric Extraction Software creates piping isometric drawings from 3-D piping models created by the PDS modeling packages.

1-2


The software consists of two principal components: ISOGEN, which draws the piping isometric and places it in a MicroStation design file and Intergraph 3-D software packages which create input for ISOGEN and perform other functions necessary in final drawing creation. The software allows you to extract isometrics from a 3-D plant model: single isometrics interactively or multiple isometrics in a batch mode. The ISOGEN software is designed to be flexible because drawing practices vary from one company to another. The following features of Intergraph’s isometric extraction package allow you to specify drawing format: User-controlled ISOGEN option switches

The capability to use an alternate or foreign text

A large set of Intergraph option switches

User-controlled attribute breaks shown on drawings

A flexible method for generating notes

Attribute-driven symbology (solid or dotted lines)

User-defined component symbology

User-controlled mapping of attributes to the title block. In addition to the isometric drawing, the software also generates several nongraphic outputs, the most important of which is a completely user-definable MTO neutral file. This neutral file is extremely useful for those who want to couple a material control system with Intergraph’s 3-D modeling software. The above features are collectively referred to as software customization and are dealt with at length in this document. You will find reference information needed for customization in the appendices.

Introduction to ISOGEN 1 - 3

1.1 Overview of Isometric Extraction __________________________________________________________________________________________________________________________________________________ This section outlines the software components and how they are organized for interactively extracting isometrics.

1.1.1 The Intergraph Interface to ISOGEN __________________________________________________________________________________________________________________________________________________ The core software module in isometric extraction (both interactive and batch) is the ISOGEN interface. This program reads data from the 3-D model files and generates an input file for ISOGEN. ISOGEN knows nothing of PDS or any of its files. It reads only the input file created for it by the ISOGEN interface. While ISOGEN is primarily responsible for generating the drawing graphics (including dimensioning) the ISOGEN interface is responsible for most everything else — including note generation, recognition of attribute changes, defining which symbols to use and so on. The primary input to the ISOGEN interface is an ASCII file named pdsidf.dat. The interface reads from this file the piping and equipment models involved, the output isometric file name, and identification of all of the pipelines in the drawing. The interface also reads in data from the options file.

1-4


The options file consists of a collection of switches, options and tables that gives you some control over what the ISOGEN interface puts in its output file (called the intermediate data file or idf) and therefore what appears in the final drawing. Once this data is read in, the interface collects from the model files all of the components that make up the piping network. Data from the components is then used to form an internal data structure which represents the network. Finally, this network is traversed (the software traces a path through the piping network) and records are generated in the idf. The order of the records in the idf is in the order of the network traversal. Drawing notes and other features such as bill of material information are dealt with component by component as the network is traversed. If the components in the piping models are not properly connected or other problems exist, the internal data structure will not be properly built and isometric extraction will fail. See the section Interpreting the HITS Report for more information. The HITS report can help you to find problems in the piping model and tell you when the interface software is not working properly.

1.1.2 ASCII to Binary Conversion __________________________________________________________________________________________________________________________________________________ The Intergraph interface to ISOGEN creates an ASCII data file containing the input to ISOGEN. Since ISOGEN requires the input data to be in binary format, a program named ISOA_BGEN is run to convert this ASCII data file to binary. ISOA_BGEN creates the binary output file FOR036.# which IZOD2 uses to generate the isometric drawing.

1.1.3 ISOGEN __________________________________________________________________________________________________________________________________________________ ISOGEN takes the binary input file and generates graphics in an 2D MicroStation design file. The graphics consist of the completed isometric drawing. ISOGEN can also generate several nongraphic outputs, including: An ISOGEN MTO neutral file A parts list (bill of material) A cut pipe report A component VRS sheet number file The parts list file contains the same bill of material that is shown on the isometric drawing. It is possible to turn the drawing bill of material off and attach the printed ASCII file to the drawing instead. The cut pipe report, which shows the length of each piece of pipe in the line, can be useful. The component VRS sheet number file is used by the batch extraction software and is discussed elsewhere.

PDS Environment 2 - 1

2. PDS Environment

__________________________________________________________________________________________________________________________________________________

The PDS 3D software supports a variety of applications. All the supported applications use a common interface that is controlled by the PD Shell program. This ensures consistency across applications and minimizes the amount of time required to learn the product. The PDS 3D modules provide a simple user interface through extensive use of forms. The modules also provide an on-line Help capability for easy access to information while working in the product. The PDS 3D software uses available nucleus tools such as MicroStation and FORMS. It supports standard software such as NFS, NQS, and RIS required to set up data across a network. This design facilitates the use of non-PDS tools such as relational databases and third party software. The PD_Shell Environment and all batch jobs in the PDS 3D products interface to Intergraph’s Network Licensing System.

2-2


2.1 PD Shell __________________________________________________________________________________________________________________________________________________ The PD Shell program provides access to the various functions that are associated with the PDS 3D Modules. You can access the Plant Design System Environment form by double-clicking teh PD_Shell icon. This executes a control script that defines all of the environment variables that are needed to run the product, and it identifies the location of the product files. These files can be located on the workstation or a server on the network. See pds.cmd for more information on this file. The script also activates the Plant Design System Environment form.

This form identifies the active project(s) and provides access to all the PDS functions. Options Schematics Environment — Provides access to the PDS 2D modules that are used to create and modify piping and instrumentation diagrams, process flow diagrams, and instrumentation database records. Equipment Modeling — Provides access to the Equipment Modeling module, which provides an interactive graphics environment that is used to create and revise equipment model graphics and database information.


FrameWorks Environment — Provides access to the FrameWorks module, which provides an environment that is used to create and revise structural models, create and revise structural drawings, and propagate structural models. Piping Designer — Activates an interactive command environment that is used to create piping and in-line instrumentation in the model; revise existing model graphics and database information; and verify the integrity of the data in the model. Electrical Raceway Environment — Provides access to the Electrical Raceway module, which provides an interactive environment that is used to create and revise raceway models and access raceway utilities. Piping Design Data Manager — Provides access to a set of options that are used to verify the integrity of the graphic and database information that is associated with a model. Piping Model Builder — Enables you to create piping graphics from a nongraphics environment. This module is used with PD_Design to create an accurate 3D model of the piping network. Pipe Stress Analysis — Activates a set of forms that are used to extract information from piping models for input to third-party pipe stress analysis products. Interference Manager — Activates a set of forms that are used to check for interferences among project models and to control approved interferences. Isometric Drawing Manager — Activates a set of forms that are used to extract isometric drawings from piping models and to review or plot the created isometric drawings. Drawing Manager — Activates a set of forms that are used to create and manipulate drawings and drawing views; provide access to the interactive graphics environment for drawings; and provide access to a plot manager and vector hiddenline manager. DesignReview Integrator — Activates a set of forms that are used to extract information to form label files for use in DesignReview and to review data from a DesignReview session. Report Manager — Activates a set of forms that are used to create and revise report format files and report on information in a project including Material Take-Off reports.

2-4


Project Administrator — Provides access to a set of forms that are used to create a project, create and revise project files, define project seed data, and control the project. Reference Data Manager — Provides access to a set of forms that are used to control the reference data for a project including Piping Job Specification data, Graphic Commodity Data, Alphanumeric Commodity Data, Standard Note Library, Label Description Library, and Piping Assembly Library. Other Fields User ID — Used for access control. This field also sets the Review User ID for use in the Interference Manager module. If access control has been defined, you must key in a valid user ID as defined by your system manager to gain access to the projects. If access control has not been defined, no entry is required for this field. Password — Key in the password for the specified user ID. Project List Field — Displays the defined projects for the network and allows you to select the active project. The system lists all the defined PDS projects (2D-only, 3D-only, and 2D & 3D). An error is displayed if you select an option that is incompatible with the active project. For example, if the active project is a 2D-only project, you cannot access the the Interference Manager module. If access control has been defined, only those projects for which you have some level of access are displayed. Message Area — Displays prompts and messages that are associated with the active process. Error messages are displayed in red.


2.1.1 PD_Shell Form Conventions __________________________________________________________________________________________________________________________________________________ The following Conventions describe how to respond to the various buttons, lists, and prompts that make up the environments. The display size of forms and dialog boxes in the non-Microstation graphics environment are independent of the size of the workstation’s display system. Most forms contain the same basic features: buttons, fields, text, and other gadgets. In general, anything you find on a form is called a gadget. Selecting Options You move through the PD Shell forms by selecting function buttons or other gadgets from the form. Select means to place the screen cursor (which appears as an arrow) on top of a screen gadget and press . For most of the forms with scrolling lists, you can double-click on a row to select and accept the data in that row. This performs the same action as selecting a row (which highlights) and then selecting the Accept button. You use the select action to select functions, access other forms, activate data fields, toggle buttons, select from lists, scroll through data displayed on the screen, and so on. The following summarizes other basic actions you use in the environments: Enter — When keying in any data in a key-in field, press the or key for the data to be entered into the system. You can also press or to move through a set of key-in fields. Delete — If you make a mistake while keying in text, press the key to erase character(s) to the left of the cursor.

Common Tools on the PD Shell Forms There are many gadgets in the environments that are common to most or all of the forms. The following describes these tools. Standard Commands The PD Shell forms have a set of standard buttons in the upper right corner of most of the form windows. The available commands vary from form to form depending on the type of operation. The Help button activates on-line Help for the active form. Help remains active until you delete the Help window.

2-6


The Shell button exits the active form and returns control to the base manager that is associated with the active form. For most forms this returns to the Plant Design System Environment form. The Top button exits the active form and returns control to the top form of the active branch. The Cancel button cancels or exits from the active form. Control returns to the immediately preceding form in the hierarchy. The Accept button accepts a selection or operation. Depending on the active form or option, the active form remains active so that you can repeat a similar operation or control returns to the preceding form. The Restart button clears any key-in fields on the form that have values you can modify. Scrolling List Some screen menus have a scrolling list of projects or applications. You need to scroll a list only if more options are available than can be displayed in the window. To scroll a list, select the arrow buttons on the side of the list. The list scrolls up or down depending on which arrow you select. The scrolling list has an arrow pointing up and an arrow pointing down. These arrows scroll lists line by line. There is a button that slides between these two arrows to indicate your position on the list. To page through the list, select the space above or below the sliding button. The list pages up or down accordingly. You can also select the slider and, while pressing , slide the button up or down the bar. The items scroll through the window as you move the button. The size and position of the button on the scroll bar is an indication of the number of lines and the relative position within the list. All commands that display a list of design areas or models order the list alphanumerically by the design area number or model number in ascending order. In some forms with scrolling lists, you can double-click on a row to select and accept the data in that row. This performs the same action as selecting a row (which highlights) and then selecting the Accept button.


Key-in Fields Screens that accept keyboard input have key-in fields. These fields are box-shaped and dark gray. You can select a key-in field and key in a new value. A bar cursor appears in the active key-in field. Key in your input, and press . To change a field, reselect the field and key in the new information. Key-in fields have a maximum number of characters depending on the item that is being defined. If you select a key-in field for a code-listed attribute, the system activates a form that lists the code list values for the selected field. MicroStation requires lowercase characters for the file specification and path name of all design files. Therefore, the system automatically converts any input for the file specification and path name of a design file (such as a model or drawing) to lowercase before loading into the Project Control Database. Display-List Boxes A display-list box is located at the end of some key-in fields. It lets you select data from a list instead of keying in information. For example, there is a display list associated with the Authorization key-in field shown. At the end of the field, there is a small box with horizontal dashes. When you select this display list box with the screen cursor, an associated list of valid input values displays. Select an item from the list to enter its value into the field. Shift Left and Shift Right buttons At the bottom of some key-in and display fields, there are two buttons marked with arrows. These buttons are called shift left and shift right buttons. Often, you can key in more characters than a field display shows. Shift Left moves the text display to the front of the field; Shift Right moves the text display to the end of the field. Toggle A toggle field on a screen menu enables you to select one of two possible choices, one of which is always displayed. Place a data point on the toggle field to toggle between the two choices. Roll-Through List A roll-through list shows one choice at a time of a list that can be several items long. Place a data point on the roll-through list to scroll through the available options. The option displayed is active.

2-8


Standard Window Icons When using this software in the CLIX environment, you can press along the edge of a form or any area not occupied by a button, key-in field, or other gadget, to display a box of icons. You can manipulate form windows just like any other workstation window. The following list defines the available window icons. Collapse/Restore Repaint

Pop-to-bottom Modify/Resize

Pop-to-top Restore Size

2.1.2 Batch Processes __________________________________________________________________________________________________________________________________________________ When you install the PDS 3D applications, the system creates the necessary batch queues for that application. Refer to Loading PDS Products in the Project Administrator (PD_Project) Reference Guide for a listing of the batch queues. PDS 3D uses these batch queues to allow you to continue working in the environment while the system processes a request. Many of the batch processes can be delayed for submission at a specified time. When you submit a batch process the system sends an e-mail message to the mail path of the default login reporting the job’s completion status and any error log information. The batch process e-mail functionality is optional.

Interactive Isometric Extraction 3 - 1

3. Interactive Isometric Extraction

__________________________________________________________________________________________________________________________________________________

This section explains how to execute the software that generates isometrics interactively. You can extract only a single isometric at a time using the interactive modules. Also, this mode of extraction is intended primarily for testing purposes. Many extraction facilities are not available using interactive extraction. You must have access to an existing PDS Piping model that contains a completed pipeline before an isometric can be generated.

Operator Sequence 1.

After accessing the PDShell form, select a project from the scroll area. The system highlights the project. Select the Isometric Drawing Manager button to enter the ISOGEN environment.

The system displays the Plant Design - Isometric Extraction form and prompts: Initializing Project Control Database. The active project name is also displayed in the field located in the upper left portion of the form.

3-2

2.


Select the Interactive button. The system displays the Interactive Isometric Extraction form.

3.

If you know the information, keyin the appropriate Model Numbers and Line Names and proceed to step 10. Otherwise, continue with this procedure.

4.

Select the Select Model Numbers button.


The system displays an Interactive Isometric Extraction form that lists all of the piping and equipment models within all of the areas from the active project.

5.

Select the models from the scroll area that contain the lines that are to be extracted. — OR — Select the Select All button to select all of the areas and models listed in the scroll area. — OR — Select the Reset Selection button to cancel all of the previous model selections. Up to eight models can be selected for extraction.

6.

Once all of the appropriate models have been selected, select accept. The system returns to the initial Interactive Isometric Extraction form. If necessary, you can select the Reset Model Numbers button to clear selections in the Model Number and Line Name fields.

7.

Select the Select Line Names Within Models button. The system displays an Interactive Isometric Extraction form that lists all of the lines contained in the selected models. There may be a slight delay while the system searches for the selected lines.

3-4

8.


Select the line names from the scroll area that are to be extracted. — OR — Select the Select All button to select all of the lines listed in the scroll area. — OR — Select the Reset Selection button to cancel all of the previous line selections. Up to eight lines can be selected for extraction. All lines to be extracted must be connected in the piping model. For more information about extractions using pipeline names, see Pipeline Names, page 3 - 10 .

9.

Once all of the appropriate lines have been selected, select the accept button to return to the initial Interactive Isometric Extraction form. The system returns to the initial Interactive Isometric Extraction form with the selected models and pipeline names in their respective fields. The system also generates an iso design file name based on the first pipeline name and places it in the Iso Design File field.


If necessary, you can select the Reset Line Names to clear selections in the Line Name fields. You can also select the Reset Model Numbers button to clear selections in the Model Number and Line Name fields.

10.

Iso Output Node:Path Select the Iso Output Node:Path field and key in the nodename:path where the ISOGEN output files will be stored. The default is set to nodename:/login directory. The key-in fields: Iso Output Node:Path, Iso Options File and Iso Seed Design File will accept a network address. Each should be entered as nodename:drive:\directory path\filename for example: 111jn:C:\win32app\ingr\dat\defaults.dat.

To change the default settings for the Iso Output Node:Path field, edit the ISOPATH export statement. Edit the pds.cmd file located in ˜\pdiso\bin. For example, a typical ISOPATH export statement in the pds.cmd file might be: $ENV{’ISOPATH’}=’PDSNT:C:\users\iso\isofiles\\’;

11.

Iso Design File Select the Iso Design File field and key in the ISOGEN design file. By default, the first pipeline name is displayed with a .iso extension.

3-6


The .iso extension will generate multi-sheet isometrics into a single design file. Replacing the .iso extension with a .i* extension allows the software to generate multi-sheet isometrics into separate design files where the * will be replaced with a number. For example, if the model in the Interactive Isometric Extraction form was changed to 400104wc.i*, the resulting design files would be 400104wc.i01, 400104wc.i02,, etc. This procedure will allow you to take advantage of ISOGEN’s plotting capabilities as described in the section Plot Isometric Drawing. The the most recently processed iso, displayed in the Iso Design File, becomes the first selection on the list of available isos when the Plot or View Graphics command is selected. 12.

Iso Options File Select the Iso Options File field and key in the nodename:path where the ISOGEN options file is located. If you key in an options filename and the file does not exist, an error message is displayed at the bottom of the form. The options file contains switches, options and tables that drive the Intergraph interface to ISOGEN. This file allows you to customize iso’s to your standard practice. The default is set to nodename:/pathname. The default value is delivered in the options file and can be altered by exporting the ISOOPTION variable.

13.

Iso Seed Design File Select the Iso Seed Design File field and key in the nodename:path where the ISOGEN seed design file is located. If you key in a seed filename and the file does not exist then an error message is displayed at the bottom of the form. The iso seed design file is a 2-D design file that is copied to create an empty design file into which the isometric is drawn by ISOGEN. The default is set to nodename:/path name/iso seed file. The default value is determined when the ISOSEED export variable is defined. To change the default settings for the Iso Options File and Iso Seed Design File fields, edit the ISOSEED and ISOOPTION export statements in the PDS.CMD file. The following are examples of typical ISOSEED and ISOOPTION export statements as they would appear in the defaults.dat file. export ISOSEED=$ENV{’ISOSEED’} = ’pdssrv:D:\proj\iso\ref\isoc.sed’ export ISOOPTION=$ENV{’ISOOPTION’} = ’pdssrv:D:\proj\iso\ref\isoc.def’


14.

Select the accept button to accept the information displayed in the form and to initiate the iso extraction process.

The system displays the message Creating ISOGEN Intermediate File and then Creating ISOGEN Isometric. When the process is complete, the system displays the PD ISOGEN Status form.

The ISOGEN Status form displays processing information, warning messages and error messages. Use the scroll bar and buttons to scroll through the information displayed on the status form. See Appendix A Error Messages for detailed descriptions of each error and warning message.

3-8


15.

To plot an isometric drawing using the Plot button, refer to Plot Isometric Drawing, page 3 - 14 .

16.

To view an isometric drawing using the View Graphics button, refer to View Isometric Drawing, page 3 - 17 .


3.1 Extraction Criteria __________________________________________________________________________________________________________________________________________________ The following sections contain information specific to defining extraction criteria which must be defined prior to initializing an isometric extraction. The following extraction criteria are covered in this section: Model Files Pipeline Names –

Generation by Line Name Substring

–

Generation by Line ID

Iso Design File

3.1.1 Model Files __________________________________________________________________________________________________________________________________________________ Key in the names of the PDS Piping, Equipment Modeling and/or Pipe Support files that should be considered for iso extraction. Up to eight model numbers can be input. Equipment model numbers must be specified in order to generate nozzles on the isometric. The first model number entered is treated as the primary file and therefore must be a Piping model. Any RDB data accessed during iso extraction is obtained from the primary model (through its type 63 data). The RDB data that is accessed by the Iso Extraction Software and that must be properly attached to the primary file includes: Specification Material Database Graphic Commodity Library Physical Dimension Library Piping Job Spec Tables Library Standard Notes Library Material Descriptions Library Specialty and Instrument Descriptions Library Label Description Library Miscellaneous data stored within the model itself

3 - 10


If the model number that you specify does not exist, the software displays an error message at the bottom of the form. Press to proceed. If the model number is invalid, the software displays the message Error Retrieving Model and the fully expanded filename is displayed in the input field. A filename is considered invalid if it does not exist in the project database.

3.1.2 Pipeline Names __________________________________________________________________________________________________________________________________________________ Key in the pipe lines that are to be extracted into a single iso. Up to 8 lines can be specified. The lines you specify must be connected together in the Piping Model files. That is, these pipelines must be a network of piping segments. In order for the lines to be connected, the segments that form those lines must also be connected. You cannot specify multiple disconnected piping sections (such as, vessel trim piping). Pipelines can be identified for extraction in two ways: extraction by line name substring and extraction by line id (see the section Conventions and Limitations). The method you use depends upon the options selected and set in the iso extraction options file. Refer to The Options File, page 7 - 1 for more information. For each method, you identify the network of piping to extract by specifying piping segment attributes. Piping segments usually correspond only to sections of piping and NOT to an entire piping system (unless the line is trivial).

Extraction by Line Name Substring When extracting by line name substring you should key in any substring of the full PDS line name that uniquely identifies the pipeline you want to include in the iso. This is the default way of identifying pipelines to extract as defined in the LINE_ID_DEFINITION section of the defaults.dat file. Example 1: If the line name is 6IN-OWS10111-1C0031 then a substring that you might use to identify this line is OWS10111. You probably would not want to use 1C0031 since it is the spec name component of the line name and would probably identify more than one line in the model. Likewise, you would probably not want to use 6IN-OWS10111 since you may want to extract sections of the line that are not 6" NPD or because multiple 6" sections are connected together by sections that are not 6". Do not extract by line name substring if lines that are similarly named exist together in the models that you are extracting from. This situation exists, for example, when the substring you want to use is also a substring of another line name.


Example 2: If the line that you want to extract is 8IN-OWS1011-1C0031, and you use the substring OWS1011, you are also specifying that you want to extract 6INOWS10111-1C0031 because OWS1011 is a substring of OWS10111. To ensure that you are extracting the correct line: specify a larger substring of the line name for the line you want to extract. In the case above, that larger substring may be -OWS1011-. By including the dashes the substring specified is no longer a substring of 6IN-OWS10111-1C0031. specify the line ids of the lines you want to extract. Refer to Extraction by Line ID, page 3 - 11 for more information.

Extraction by Line ID When extracting by line ID you key in the line ID of the lines that you want to extract. The line ID is a user defined collection of database attributes that can be used to refer to pipelines by other than their line names. To extract by line ID, you must select the proper option in the Options File AND you must know the line ID definition as specified in the options file (refer to LINE_ID_DEFINITION, page 7 - 59 for information on defining the line ID). To extract a line by its line ID, key in the attributes that make up the line id and separate them by dashes. Example 3: One simple definition of the line ID might be fluid code followed by line sequence number. This definition allows you to refer to the line without the NPD or spec name components the line name. Thus, OWS-1011 will refer to line 6INOWS1011-1C0031 while OWS-10111 will refer to line 8IN-OWS10111-1C0031. When specifying the line ID of a line to extract, both the embedded dashes and the ORDER of the attributes is important. Thus in the example above, neither OWS1011 (because the dash is missing) or 1011-OWS (because the order is incorrect) would suffice if the line ID is defined as fluid code followed by line sequence number. The difference between extracting by line ID and extracting by line name substring is that pipeline sections that are extracted are identified by EQUALITY of the line ID attributes rather than by SUBSTRING of the line name attribute. This method of identifying lines avoids the problems that can occur with line name substrings (provided that the line id definition is sufficient to uniquely identify pipe lines).

3 - 12


3.2 Iso Design File __________________________________________________________________________________________________________________________________________________ Key in the name of the output isometric design file. This file need not exist prior to running the software. If the file does exist, the software replaces it with a new file when the current iso is extracted. To specify that each isometric sheet is to be drawn in its own design file, you can insert an asterisk (*) as a wild card character in the output iso filename. When a wildcard character is inserted in the filename, the software replaces it with a digit as each iso sheet is generated. If more than 9 sheets are generated then the letters a - z are used for replacement of the wildcard. You may also use an asterisk (*) in the output file name’s extension. If you do this, the asterisk is replaced by two digits. For example, if you key in test.i*, sheet 1 will be in file test.i01, sheet 2 will be in test.i02, and so on. Since UNIX file names cannot have more than 14 characters, the iso design file name is truncated to a maximum of 14 characters. Using more than one fixed character together with an asterisk is not recommended. MicroStation requires that all design file names be in lower case. If an invalid iso filename is keyed in, an error message is displayed in the message field. The name portion of this file specification (excluding any wild card character) is used by the software to name several other files that are generated at the same time as the isometric model number. These include: The Intermediate data file - iso name + .idf

The Hits file - iso name + .h

The Intergraph mto neutral file - iso name + sheet no. + .b# (where: # is the number of times the line has been extracted)

The error message file - iso name + .err

The ISOGEN mto neutral file - iso name + .bom

The ISOGEN message file - iso name + .msg

The ISOGEN printed parts list - iso name + .prt


The ISOGEN component vrs sheet file - iso name + .sed

The ISOGEN cut pipe report - iso name + .cut These files are all generated in the Iso Output Node:Path unless they are switched off by option selections (refer to The Options File, page 7 - 1 for more information). Their contents are discussed in more detail in the sections entitled Options File and Isometric Seed File.

3 - 14


3.3 Plot Isometric Drawing __________________________________________________________________________________________________________________________________________________ The Plot Isometric button allows you to choose one or several generated isometric files for plotting. 1.

To plot an isometric drawing, select the Plot button from the Interactive Isometric Extraction form. The system displays the Interactive Isometric Extraction form.

2.

Select one of the queues from the Queue Name pull down list. The queues displayed in the Queue Name field are chosen first from the queues defined in the pdiso_plot portion of the queue_descript file (located in the project directory). If no queues are defined in the queue_descript file, the system generates a Queue Name list from locally defined queues. If locally defined queues are used, only the pipe queues that are defined will be displayed in the Queue Name pull down list. To display local device queues, create a pipe queue that points to the device queue.

3.

Select the Plot Copies field and keyin the number of copies that will be plotted.

4.

Select the Iso Seed Plot File field and key in the nodename:path where the seed plotting parameters file exists. The default is defined in the ISOPLOT export variable. For more information on defining ISOGEN export variables, see Initial Setup Considerations, page 5 - 3 .


An example plot parameter file is delivered, but it should be modified before it can be used or a print queue called laser must exist. For more information on modifying the plot queue, see Creating Seed Files for Extraction, page 9 - 1 . 5.

Select the subdirectories that contain the drawings you want to plot. Select each subdirectory individually from the Sub-Directories field. The system highlights the selected subdirectories. — OR — Select the Select All Sub-Directories button to select all of the available subdirectories. — OR — Select the Reset Selected Sub-Directories to cancel any of the previously made selections.

6.

Once you have defined a list of subdirectories, select the Display Iso Drawings button. The system searches the previously defined list of subdirectories and displays a listing of the available drawings, their creation dates and the subdirectories to which they belong.

7.

Select an isometric drawing(s) to plot. Use the scroll bar and buttons to view all available drawings.

— OR —

Select the Select All button to select all of the listed drawings for plotting. The system highlights the selected drawing(s). — OR — Select the Reset Selections button to cancel any of the previously made selections. 8.

Submit Batch Immediately/Delay Submit Time toggle Select the Submit Immediately option to run the job immediately. Select the Delay Submit Time to specify a run time for the job. Define the run time by keying in the day of the week (Mon, Tue, etc.), the time and then select AM or PM.

3 - 16

9.


Select the accept button to accept the selected drawings for plotting. The system submits the selected drawing(s) to the plotter. As each drawing is processed, the messages Processing Drawings and Selected Drawings Submitted to Plotter appear in the message field.


3.4 View Isometric Drawing __________________________________________________________________________________________________________________________________________________ The View Isometric Drawing button allows you to view generated graphics in the MicroStation environment. If you are unfamiliar with the MicroStation working environment, refer to the MicroStation Reference Guide for more information. 1.

To view an isometric drawing, select the View Graphics button from the Interactive Isometric Extraction form. The system searches the Iso Output Node: Path (as defined earlier in the Interactive Isometric Extraction) and displays the Interactive Isometric Extraction form.

2.

Select the subdirectories that contain the drawing you want to view. Select each subdirectory individually from the Sub-Directories field. The system highlights the selected subdirectories. — OR — Select the Select All Sub-Directories button to select all of the available subdirectories. — OR — Select the Reset Selected Sub-Directories to cancel any of the previously made selections.

3 - 18

3.


Once you have defined a list of subdirectories, select the Display Iso Drawings button. The system searches the previously defined list of subdirectories and displays a listing of the available drawings, their creation dates and the subdirectories to which they belong.

4.

Select an isometric drawing to view. Use the scroll bar and buttons to view all available drawings. The system highlights the selected drawing.

5.

Select the accept button to accept the selected drawing for viewing. The system displays the message Initializing MicroStation in the message field and displays the isometric drawing. MicroStation will automatically attach the bar and panel menus.

6.

Select the exit button to exit the MicroStation environment and return to the View Isometric Drawing form.


3.5 Conventions and Limitations __________________________________________________________________________________________________________________________________________________ Some situations that occur commonly can be handled in more than one way by the iso extraction software. To deal with these, a set of conventions, described below, has been adopted. Other situations that can arise simply cannot be handled by the extraction software as it is currently written. A brief summary of these items is also provided below.

3.5.1 Extraction Conventions __________________________________________________________________________________________________________________________________________________ Olet Type Branches Olet type branch components (such as olets, branch-welds, and occasionally half couplings) can be owned by the header or branch pipeline in the 3-D model. By convention, when this type of branch is extracted, the branch component is assigned to the header pipeline. Thus, when the branch line is extracted, the branch component will be drawn dotted, no-mto and it will not appear in the BOM. However, you can specify that the branch component is assigned to the branch line. This depends on the position of the Header/Branch toggle on the Piping Data Control Form (accessed through Project Administrator). For more information on the Piping Data Control Form, see the section entitled Piping Data Control in the PD Project Administrator Reference Guide. It is NOT necessary that the piping segment in the model, under the branch component, have the same line name as the header.

End-Point Components When a pipeline in the model changes name at a multi-connect point component then that component is "owned" by more than one line. When this occurs, the component is always assigned to the pipeline attached to connect point 1 of the component. For example, if three different lines come together and join at a tee, the tee component will extract onto, and show up in the B.O.M. of, the line at connect point 1 of the tee. When the other two lines are extracted, the tee will show up as dotted, nomto and will not appear in the B.O.M. (Notice that it is NOT necessary that piping segments in the model be "broken" in any way to achieve the above result.)

3 - 20


Implied Materials at Line Name Changes When a pipeline name changes at a flanged connection, the bolts and gaskets generated at that point may be assigned to either of two lines. In this situation, the bolts and gaskets are assigned to the flange having the higher east, north and elevation coordinate. This arbitrary assignment prevents the implied materials from being generated twice. (It is possible to override this assignment; refer to the PDS Piping Design Graphics Reference Guide for details.)

Pipe Supports Pipe supports in the 3-D model may be attached anywhere along the length of a pipe except at either of the end-points. They may also be attached to the origin (connect point 0) of any component as well as to a component tap. You may have multiple supports connected to a component origin, but there should be at most one support attached to a component tap. When a support is connected to a tap, there must NOT be any other piping attached to the component at that tap. In general, supports should NOT be located at component connect points other than as outlined above. The one exception to this rule is that supports may be located at the same point as an olet branch (or branches) along a length of pipe. If these guidelines are not followed, the line may not extract.

Type 63 Information Type 63 data is read from the first model entered on the form for Interactive Extraction. When using Batch Extraction, Type 63 data is read from the first piping model in the area specified in each record of the batch input file.

3.5.2 Extraction Limitations __________________________________________________________________________________________________________________________________________________ Branch Nesting There is a limitation on the branch nesting depth that a pipeline may have. The first branch off from a line is level 1. If this branch in turn has a branch, then that branch would be level 2. ISOGEN will currently handle pipelines that contain up to twenty levels of branching. If a pipeline contains more than twenty nested branches, the extraction will fail. This limitation effectively limits the size of the largest system type isometric that can be extracted. This generally does not pose a problem for single pipeline fabrication type isometrics. Note, that the ISOGEN interface identifies a traversal sequence that minimizes the number of nested branches in most cases.


System Isometrics Spool Numbering is not supported for system-type isometrics.

Tapped Piping Components ISOGEN requires that traversal of a pipeline never enter a component through a tap. Rather, in traversing the line, ISOGEN requires first traveling through a component and then traversing "out" the tap. It is possible to create a pipeline in the 3-D model that would require the ISOGEN interface to illegally traverse into a tap. You can avoid this situation by NOT joining components through taps. For example, a segment of pipe that begins at a component tap should not end at a tap on different component. If this situation cannot be avoided, change the line name somewhere and extract the network in two sections. Other limitations having to do with tapped components include: 1) Elbows and pipe bends must not have more than one tap. It is possible to create a model where an elbow is tapped more than once, but this configuration will not extract. 2) Tapped tee’s cannot be extracted using ISOGEN.

Flanged Pipe Taps that are placed on flanged pipe will not extract. Refer to Intergraph option 72 for settings that impact flanged pipe.

3 - 22


Batch Software Organization 4 - 1

4. Batch Software Organization

__________________________________________________________________________________________________________________________________________________

This section provides an overview of the batch extraction software components and organization. The purpose of this section is to explain to software support personnel how the software works so that problems can be tracked down and reported. Figure 4-1 shows the batch software organization. The batch extraction software is driven by an executable pdsidf and a script file batch.cmd. When you submit a batch job using the Schedule Batch Job form, the batch extraction is submitted to a batch queue named PDisocreate. This queue is created with a job limit of 1 and a priority of 16. These parameters can be modified as needed. In order to run batch isometrics, the pd_iso.cmd file, located in ˜\pdiso\bin, must define locations for required software. This script is executed from the batch queue and allows the batch extraction process to run on a node other than the one from which it was submitted. The following three variables are read from the Windows NT registry: PD_SHELL PD_ISO PD_ISOGEN

4-2


Figure 4 - 1. Batch iso extraction flow


4.1 The Batch Job Input File __________________________________________________________________________________________________________________________________________________ The input to the batch procedure is an ASCII data file generated by the Batch Environment called the Batch Job Input File. This file is structured as shown in Figure 4-2.

Figure 4 - 2. Batch input file data structure The first record in the file contains a file format version number and the name of the Batch Data File from which the Batch Job Input file was generated. The software checks the version number to see if it matches the software version number, and, if it does match, passes the Batch Data File name on to other software modules as needed. The second record is called an option record. The option record contains all of the batch processing options and revision block data that was entered into the BATCH form. Each option is separated from the others by at least one space. This record contains an exclamation point (!) in column 1 which flags it as an option record. The third record holds the name of the default set which was specified in the Create Batch Job Input form. This record also contains an exclamation point in column 1. Subsequent records, which initially contain a space in column 1, hold the model and primary line name for an isometric drawing which will be extracted. After the line is extracted, it is marked by an asterisk (*) in column 1 to indicate that it has been processed. The drawing records can be repeated any number of times in the batch job input file. Each time Accept is selected, from the Create Batch Job Input form, a set of drawing records is written to the batch input file. An example batch job input file is shown in Figure 4-3.

Figure 4 - 3. Example Batch Job Input File

4-4


When a batch iso job is submitted using the Schedule Batch Job form, the batch job input file name is passed to the pdsidf executable as a parameter. The system then reads the batch job input file and drawing creation begins.

4.2 Line Processing (pdsidf) __________________________________________________________________________________________________________________________________________________ Given the options from the batch input file and the identification of the line, two files are created, seed.dat and pdsidf.dat. These are the same two files that are created during interactive extraction. The Project database is accessed to obtain the list of model files, secondary pipeline names, the seed file names, the options file for the piping area, the output file directory, the iso design file name and the extraction number for the drawing. Type 63 information is read from the first piping model in the area specified in each record of the batch input file. Note that this model may not be the piping model which contains the pipeline being extracted. The two files produced are different from the ones produced for interactive extraction. In pdsidf.dat, the first line name in the line name list is followed by a backslash and the piping area name. Following the line list is a record that contains the default set name. Next is a record that contains batch processing options. The last record contains the extraction number for the drawing. skiso5 skiso4 skiso6 skiso7 *skiso3 40eqp01 40eqp00 pdssk:h:\proj\iso\isofiles\380105wc.i* 380105\skiso\1 proj N Y Y N * * Y * * 04-Aug-1998 * 13 1 0


In SEED.DAT, the seed iso design file name is followed by records containing the plot request file name, the output file directory, the output iso file name, extraction number and number of sections. pdssk:h:\proj\iso\ref\isoc.def pdssk:h:\proj\iso\ref\isoc.sed pdssk:h:\proj\iso\ref\isoc_sml.i pdssk:h:\proj\iso\isofiles 380105 13 1.fi

4.3 The ISOGEN Interface __________________________________________________________________________________________________________________________________________________ The ISOGEN interface performs the same function in batch extraction as in interactive extraction: generation of the Intermediate Data File (IDF), which is the input to ISOGEN. In addition to the IDF the interface may also produce an mto neutral file and three files containing text for the drawing title block. The title block text files are shown symbolically as a single file in Figure 4-1. The contents of each of the title block tables file is controlled by a corresponding table in the title block tables file map. The SEGMENT_DATA_TABLE produces a file with the file extension of .seg, the DRAWING_DATA_TABLE produces a file with the extension of .bit and the SHEET_DATA_TABLE produces a file with the extension of .dwg. The title block text files are only produced if the appropriate option is set in the Intergraph options block. Some of the entries in the DRAWING_DATA_TABLE can only be produced when PDSIDF.DAT contains the extra inputs that appear in the file for batch extraction. A title block record map set up for use with batch extraction might not generate a correct output file if it is generated by running the interactive software.

4.4 ISOGEN __________________________________________________________________________________________________________________________________________________ As in interactive extraction, in batch extraction, the program ISOA_BGEN must be run immediately prior to IZOD2 in order to convert the ASCII IDF to binary. IZOD2, the ISOGEN image which produces the iso, can then be run to generate the isometric drawings. Isometrics generated by the batch software are always created one sheet to a design file. The iso design file name is passed to the interface as name.i*, and so the first sheet will be in a file with the extension .i01, the second in .i02 and so on. When isometrics are created in batch, you must set Intergraph options block word 4 to 1. This causes ISOGEN to create a file that identifies which sheet each component in the line is drawn on. This file (called the sheet data file) is used downstream to split up the mto neutral file by sheet and also to prepare the segment summary table for each isometric sheet.

4-6


4.4.1 Splitting the MTO neutral file (MSPLIT) __________________________________________________________________________________________________________________________________________________ After IZOD2 (see Figure 4-1) runs and creates the sheet data file, Intergraph’s MSPLIT executable splits up the mto neutral file so that a separate neutral file is created for each sheet of the drawing. The sheet data file consists of sheet numbers followed by Intergraph database occurrence numbers. MSPLIT assigns each neutral file record to a particular sheet by matching occurrence numbers in the sheet data file with the occurrence number on each record in the mto neutral file. MSPLIT will not work if you have not mapped the Intergraph occurrence anywhere in the neutral file record. MSPLIT is executed by passing the mto neutral file name (without the file extension) and the extraction number as inputs in a foreign command line. Therefore, if the mto file name is test.b and the extraction number for the drawing is 10, the input parameter to MSPLIT would be formed as test 10. MSPLIT then looks for files test.b and test.sht as the input files. The current assignment for the exported variable ISOOPTION is used to obtain the mto neutral file map name. The mto neutral file map must be read so that the field containing the occurrence number can be located in an mto record. When output files are generated by MSPLIT, the output file name contains the extraction number and sheet number. For example, for sheet 2, extraction number 10, the output file name would be test2.b10.

4.5 Generating Title Block Input (TBLOCK) __________________________________________________________________________________________________________________________________________________ In the same way that MSPLIT assigns a neutral file record to each sheet in an isometric, Intergraph’s TBLOCK assigns segment data to a sheet for the segment data summary. TBLOCK assigns records in the .seg file (produced by the PD_ISO interface) to each sheet. It then sorts the records for each sheet and eliminates duplicates. Finally, TBLOCK assigns each data item in the record a text node number and sends it as output to a new file, which is input to STIB. TBLOCK is also executed by passing the input in a foreign command line. The only input in this case is the isometric file name. The input files are then determined by name plus .seg and name plus .dwg. The title block map name is obtained by reading the options file assigned to ISOOPTION.

4.6 Filling in the Title Block (STIB) __________________________________________________________________________________________________________________________________________________ After all of the input for each sheet has been determined, the executable that actually places text in the drawing title block is run. Intergraph’s STIB associates text in an input file with text nodes placed in the design file.


4.7 Plotting __________________________________________________________________________________________________________________________________________________ After drawings are created in batch they can be plotted. You can use IP_IPLOT plotting software. To submit a plot, the batch software submits a job to the batch queue named PDisoplot. The job that runs in PDisoplot actually launches the plot. Since the plot jobs are launched from a separate batch queue, you can accumulate the jobs in the queue and release them at some later time. You might also hold the jobs in PDisoplot to prevent normal production plotting queues from getting loaded down with isometric plots.

4.8 Updating the Project Database (pdsidf) __________________________________________________________________________________________________________________________________________________ After a line has been successfully extracted, the project database is updated. The extraction number and date are updated each time a drawing is completed, while the revision block is only updated if you chose to update it in the Create Batch Job Input form when you create the batch job input file.

4.9 Making a Run Log Entry (pdsidf) __________________________________________________________________________________________________________________________________________________ Making an entry into the run log is the last activity performed. The run log file name is formed using the file name of the batch job input file together with the file extension .job. An entry in the log file consists of the drawing spec (piping area plus line name), an error code, a status message, and the date and time that the run completed. This is the same information given to you in a MAIL message when an error occurs.

4.10 Investigating Batch Extraction Problems __________________________________________________________________________________________________________________________________________________ Since there are many steps involved in the generation of a completed isometric, there are many ways for the process to fail. When a problem occurs and drawing generation fails, you should follow a systematic procedure to determine the cause of the problem and, if needed, call Intergraph support and log the problem. All files will reside in the isoerr subdirectory in the specified output path location. Here is a suggested procedure: 1.

Check the run log (.job file) to get the status code and message. If there is no code or message, the batch procedure itself probably failed or was aborted. In this case, go to Step 4.

2.

Consult Appendix A for an explanation of the error determined in Step 1. The explanation of the error might be enough to enable you to resolve it easily. If not,

4-8


then the explanation should narrow down the possibilities to a certain extraction facility or a certain area within the batch procedure. For example, it could be that the ISOGEN interface failed or that ISOGEN failed.

3.

Check for error message files (.err). Sometimes the cause of an error is reported more specifically in the error log. For example, if the ISOGEN interface fails, it might be that the line did not exist in the model. This fact would be reported to you in the error message log. The .err file contains a note in the files list located near the top of the file. This note indicates which file was read for type 63 data. If any of the type 63 data which could effect the iso (for example: MTO Options, Design Monuments, etc.) has been changed, verify that the changes have been made to the file that is being read by PD_ISO.

4.

Check the log file for the batch run. Occasionally, error messages are displayed here and are not reported in the error log file. Also, if an error occurs or some module stack dumps, those conditions will be reported in this log.

5.

Rerun the line with the DEBUG and VERIFY options enabled. If the above steps do not lead to a resolution of the problem, use the DEBUG and VERIFY options to generate a detailed log file for the run. These options will also cause log files to be generated for the plotting jobs in case there is a problem with plotting. If you cannot determine the cause of the problem, the detailed log and any other pertinent files will need to be sent to Intergraph for an analysis of the problem.

Batch Isometric Extraction 5 - 1

5. Batch Isometric Extraction

__________________________________________________________________________________________________________________________________________________

This chapter describes how to set up and use the ISOGEN interface software for generating isometrics in a batch process. Batch generation of isometrics is intended to be the primary means for generating production drawings on a project. Interactive extraction is intended primarily for testing the PDS interface to ISOGEN and ISOGEN itself. Using batch Isometric extraction, you can Generate multiple drawings in a single job

Automatically fill out the drawing title block

Automatically submit the completed drawing to the plotter. Everything that is needed to extract an isometric (except for line name) is stored in the Project Control Database at the piping area level. The following are types of area information that can be found in the Project Control Database: Area name

Equipment Area

Continuation Area

User-defined information. Within an iso area, any number of isometric drawings can exist. The following are types of drawing information that can be found in the Project Control Database: The pipeline names that are included in the drawing

Revision block data

Extraction dates

User-defined information.

5-2


The Project Control Database helps you manage the isometrics produced on a project. For example, you can use the Project Control Database to keep track of when lines need to be extracted and to record and report on drawing issue dates.


5.1 Initial Setup Considerations __________________________________________________________________________________________________________________________________________________ The following procedure outlines the basic steps you should follow to use the batch extraction facility.

Create a batch options file Set up an options file to be used for batch extraction. For information on modifying the options file, see Define Default Sets, page 5 - 13 . As part of this set-up, you should also create a Title Block Map that is used in generating title block information. For more information on the Title Block Map, see Mapping Attributes to the Title Block, page 10 - 1 .

Create border and extraction seed files Create the design files that will contain your isometric drawing border and a seed file that will be copied once for each iso produced. The seed file will contain text nodes in the drawing title block. During the extraction process, the software attaches text strings to these nodes so that the title block is automatically filled out. The border file is attached to the seed file as a reference file. Refer to Creating Seed Files for Extraction, page 9 - 1 and Mapping Attributes to the Title Block, page 10 - 1 for details on setting up these files.

Set export variables Set the export variables that define drawing border location and other information that used in various areas of the software for batch extraction. ISOGEN environment variables are defined in the PDS.CMD file. The following is a list of user-defined export variables. ISOPATH $ENV{’ISOPATH’} = ’node:drive:directory path\\’; The exported ISOPATH value is loaded by default into the output path directory slot on the Add Default Set form. It is also used as a default for the output location, Iso output node:Path, when extracting an interactive isometric. ISOOPTION $ENV{’ISOOPTION’} = ’node:drive:directory path\isoc.def’; The exported ISOOPTION value is loaded by default into the Options File field on the Add Default Set form. It is also used as a default for the options file, Iso Options File, when extracting an interactive isometric.

5-4


ISOSEED $ENV{’ISOSEED’} = ’node:drive:directory path\isoc.sed’; The exported ISOSEED value is loaded by default into the Seed File field on the Add Default Set form. It is also used as a default for the seed design file, Iso Seed Design File, when extracting an interactive isometric. ISOPLOT $ENV{’ISOPLOT’} = ’node:drive:directory path\isoc_sml.i’; The exported ISOPLOT value is loaded by default into the Plot File field on the Add Default Set form. It is also used as a default for the plot parameters file, Iso Seed Plot File, when plotting an interactive isometric. ISOBORDER $ENV{’ISOBORDER’} = ’node:drive:directory path\isoc.brd’; The exported ISOBORDER value is loaded by default into the Border File field on the Add Default Set form. ISOBATCH $ENV{’ISOBATCH’} = ’node:drive:directory path\isobat\\’; The exported ISOBATCH value is loaded by default into the Batch Job Input File field on the Create Batch Job Input form. ISOREPORT $ENV{’ISOREPORT’} = ’node:drive:directory path\isorpt’; The exported ISOREPORT value is loaded by default into the Output File field on the Batch Data Reports form. ISOBATCHQUE $ENV{’ISOBATCHQUE’} = ’PDisovreate’; The exported ISOBATCHQUE value is loaded by default into the Process Queue field on the Schedule Batch Job form. ISO_ASCII_LOAD $ENV{’ISO_ASCII_LOAD’} = ’node:drive:directory path\isoascii’; The exported ISO_ASCII_LOAD value is loaded by default into the Filename field on the Bulk Load Lines From ASCII File form.


PDISOFONT $ENV{’PDISOFONT’} = ’XX’; The defined font must be a mono-spaced font. The exported font PDISOFONT value defines the font that will be used on the output isometric, both on the body of the iso, and on the MTO on the face of the iso. The defined font must be a mono-spaced font. SYMDGN, SYMNDX and SYMLIB $ENV{’SYMDGN’} = ’node:directory path\symbol.dgn’; $ENV{’SYMNDX’} = ’node:directory path\symbol.ndx’; $ENV{’SYMLIB’} = ’node:directory path\symbol.lib’; The exported values SYMDGN, SYMNDX and SYMLIB are loaded into the Symbol Design Node:File, Symbol Index Node:File and Symbol Library Node:File fields respectively on the Isometric Symbol Editor form. ISOUSRREFDIM Variable and Pointing to a Specific FW+ ASCII File This variable overrides the setting for the data file used in generating isometric drawings with references to gridlines or structural columns. $ENV{’ISOUSRREFDIM’}=’node:directory path\filespec.dat’; Where:

filespec.dat is the name of the gridline reference data file.

For example: $ENV{’ISOUSRREFDIM’}=’pdsserv1:e:\proj1\project\fw_bldg_a.dat’; Intergraph option 71 must be enabled before data in the filespec.dat file can be referenced. The following rules apply when using the ISOUSRREFDIM variable: If the variable is set and points to the proper location of a valid gridline reference data file, the file will be used for placing structural references on the isometric drawing. If the ISOUSRREFDIM variable is set incorrectly (for example, typos in the UNCpath or filespec), references are not displayed on the isometric drawing. If the ISOUSRREFDIM variable is not set in the pds.cmd file, gridline dimensions are extracted from the fw_projname.dat file by default.

5-6


Overiding the default reference dimension file can be useful in situations where a line passes between two buildings and you want to force the dimension from a specific building rather than using the closest dimension point. See Generate FrameWorks Reference Dimension File, page 5 - 86 for more information on the FrameWorks Dimension File.

The MicroStation uconfigure.dat file To avoid problems while using the batch extraction feature, edit the MicroStation configure.dat file and comment out the command line which generates the uconfig.dat file. #do user configure.dat(uconfigure.dat) #[ -f $MS_DIR/cfg/uconfigure.dat ] && . $MS_DIR/cfg/uconfigure.dat

The problem can occur when a uconfigure.dat file, generated for one project, overrides another project’s export statement. This causes the isometric extraction to fail when areas, models, and lines can not be located.


5.2 Basic Workflow for Running Batch Isometrics __________________________________________________________________________________________________________________________________________________ Define default setups Using the information from pre-defined export variables, define a default setup. A default setup contains the network address, directory and file specification for each of the following: options file seed file plot parameters file output path border file Exported information can be overwritten.

For more information on defining a default set, see Define Default Sets, page 5 - 13 .

Select project options Select the project options that define values throughout the project. These options include: Iso Name Option - sets the convention for naming iso design files. Drawing Number Option - sets the convention for for defining drawing names. Project Default Set - defines the set that is used in bulk load and generating isos Output Path Option - uses the area name in defining the output directory path for isos. The area name is appended to the output path assigned in the default set as subdirectory. For more information on defining project options, see Define Project Options, page 5 - 22 .

Add drawings to the newly created iso area For each pipeline that you wish to extract in batch you must first create a drawing. A single piping area will normally contain many drawings; usually one per each pipeline in the design files that comprise the area. When a drawing is created, define the name(s) of the pipeline(s) to be associated with the drawing, the output design filename and drawing number. The data stored for the piping area together with the data stored for a drawing provide all the same inputs you supply when using interactive extraction.

5-8


In either method, the drawing must be defined matching the format defined in the LINE_ID_DEFINITION section of the options file. You can add drawings to a piping area by either keying in the data or downloading data from an existing model. If data from an existing model is used to define a drawing, the drawing can be created automatically. For more information see Utilities, page 5 - 56 .

Generate a Batch Job Input File A Batch Job Input File specifies run options and drawings/line names for isometric generation. When the batch job finishes, the Batch Job Input File can be either be deleted or edited so that it can be resubmitted. For more information on generating a batch job input file, see Create Batch Job Input, page 5 - 89 .

Batch Processing Considerations To achieve optimum performance of Piping Isometrics in batch mode, it is necessary to understand how PD_ISO processes a batch job. As the PD_ISO software begins processing in batch mode, it creates an empty MicroStation design file in a temporary directory on the processing machine. Then, a number of piping and equipment models are attached as reference. The quantity of attached models is based on the setting of Intergraph option 60 and the continuation areas as defined through the Batch Isometric environment.

Initiate the batch job The batch job is initiated by submitting the Batch Job Input File. A batch job can be submitted either immediately or scheduled for a later time. For more information, see Schedule Batch Job, page 5 - 100 .

Initial Workflow for Running Batch Isometrics


5.3 Batch Isometric Generation __________________________________________________________________________________________________________________________________________________ This section explains how to execute the software that generates isometrics in batch mode. You must have access to an existing PDS Piping model that contains a completed pipeline before an isometric can be generated.

Operator Sequence 1.

Select a project from the project display field. The system highlights the project.

2.

Select the Isometric Drawing Manager button to enter the extraction environment.

The system displays the Plant Design - Isometric Extraction form and prompts: Initializing Project Control Database. The active project name is also displayed in the field located in the upper left portion of the form.

5 - 10

3.


Select the Batch button from the Isometric Extraction form. The system activates the Batch Environment form.

4.

Select Option Select one of the appropriate options from the Batch Environment form.


Adds, revises, deletes or copies an isometric extraction default set(s). For more information, see Define Default Sets, page 5 - 13 . Defines a project setup from user-defined default sets, a format for the Iso Name option and the Drawing Number Option, and sets an optional path (by area name) for ISOGEN output. For more information, see Define Project Options, page 5 - 22 . Revises the data associated with an existing area. For more information, see Revise Iso Area, page 5 - 25 . Creates a new drawing and adds it into the Project Control Database. A drawing must be added to the Project Control Database prior to extracting it in batch mode. Each time a drawing is added to the Project Control Database, you define which pipelines in the model are included in the isometric drawing. For more information, see Create Drawing, page 5 - 28 . Revises single or multiple drawings. For more information, see Revise Drawing, page 5 - 33 . Deletes single or multiple drawings from an iso area. For more information, see Delete Drawing, page 5 - 46 . Lists all of the drawings within an iso area. Each listing includes information such as primary line name (secondary and tertiary are optional), drawing number, batch reference number and iso type. For more information, see List Drawings, page 5 - 54 . Accesses the utilities menu. The utilities are provided to help simplify the loading of drawings and/or areas. For more information, see Utilities, page 5 - 56 .

5 - 12


Generates a batch extraction job file. The batch extraction job file consists of your inputs for some batch processing options and a list of all the drawings to be processed in a batch run. For more information, see Create Batch Job Input, page 5 - 89 . Schedules or submits a batch job for a previously created batch input file. For more information, see Schedule Batch Job, page 5 - 100 . Generates reports on the data in the Project Control Database. For more information, see Reports, page 5 - 104 .


5.3.1 Define Default Sets __________________________________________________________________________________________________________________________________________________ The Define Default Sets option allows you to add, copy, revise or delete iso extraction default sets. Default sets are used by the extraction software to determine the location of: Option File Seed File Plot File Extracted Isos Border File 1.

Select the Define Default Sets button from the Batch Environment form. The system displays the Isometric Extraction Default Sets form.

Initially, no default set is defined. The section Add Default Set contains the procedure for add default sets.

5 - 14

2.


Select the Add button to add a default set.

— OR —

Select an existing default set and either the Revise, Delete or Copy button. The system activates the selected default set and returns to the Batch Environment form.


5.3.1.1 Add Default Set __________________________________________________________________________________________________________________________________________________ 1.

Select the Add button from the Isometric Extraction Options Sets form. The system displays the Add Default Set form.

2.

Key in a default set tag name. The system displays the Network Address, Directory and Specification fields with values as defined by the export variables. For more information on export variables, see Initial Setup Considerations, page 5 - 3 .

3.

Key in a default set description.

5 - 16

4.


Key in the appropriate information for each field. Option File The fields associated with the options file define the name and location of the option file to be used. Seed File The fields associated with the seed file define the name and location of the seed file to be used. Plot File The fields associated with the plot file define the name and location of the plot file to be used. Output Path The fields associated with the Output Path fields define the location of the iso extraction files. Border File The fields associated with the border file define the name and location of the border file to be used.

— OR —

If the export statements are defined in the control shell, the above fields will be loaded automatically. The following are examples of export statements that can be used in the control shell. export ISOPATH=/usr/wp114b/isocert/ export ISOSEED=/usr/wp114b/isocert/isoc.sed


export ISOOPTION=/usr/wp114b/isocert/isoc.def export ISOPLOT=/usr/wp114b/isocert/isoc_sml.i export ISOBORDER=/usr/wp114/isocert/isoc.brd 5.

Select the accept button. The system adds the new default set to the database and returns to the Isometric Extraction Default Sets form.

5 - 18


5.3.1.2 Revise Default Set __________________________________________________________________________________________________________________________________________________ The Revise Default Set command allows you to revise an existing iso default set. 1.

Select the Revise button from the Isometric Extraction Options Sets form.

2.

Select the default set to be revised from the list of default sets. The system highlights the default set and displays the Revise Default Set form.

3.

Select the appropriate fields and key in the new information.

Option File The fields associated with the option file define the name and location of the option file to be used.


Seed File The fields associated with the seed file define the name and location of the seed file to be used. Plot File The fields associated with the plot file define the name and location of the plot file to be used. Output Path The fields associated with the Output Path fields define the location of the extracted iso files. Border File The fields associated with the border file define the name and location of the border file to be used. 4.

Select the accept button. The system revises the default set, updates the database, and returns to the Isometric Extraction Default Sets form.

5 - 20


5.3.1.3 Delete Default Set __________________________________________________________________________________________________________________________________________________ The Delete Default Set command allows you to delete an iso default set. 1.

Select the Delete button from the Isometric Extraction Options Sets form.

2.

Select the default set to be deleted from the list of default sets. The system highlights the default set and displays the Delete Default Set form.

Information displayed on this form is for review purposes only.

3.

Select the accept button. The system deletes the default set and updates the database.


5.3.1.4 Copy Default Set __________________________________________________________________________________________________________________________________________________ The Copy Default Set command allows you to copy an iso default set. 1.

Select the Copy button from the Isometric Extraction Options Sets form.

2.

Select the default set to be copied from the list of default sets. The system highlights the default set and displays the Copy Default Set form.

3.

Key in a tag name for the new default set.

4.

Key in a description for the new default set.

5.

Select the accept button. The system makes a copy of the selected default set with the new tag and description.

5 - 22


5.3.2 Define Project Options __________________________________________________________________________________________________________________________________________________ The Define Project Options command allows you to define project options such as Iso Name option, Drawing Number option, project default set and output path option. 1.

Select the Define Project Options button from the Batch Environment form. The system displays the Isometric Extraction Project Options form.

2.

Iso Name Option Set the Project Default toggle to either By Line ID or By Area and Line ID. — By Line ID refers to the line ID as defined in the options file. — By Area and Line ID uses the first character of the area name as a prefix to the line ID. Select the Label Number and key in a label number as it exists in the Reference Data Manager’s label description library. For more information on the label description library, refer to the PDS Reference Data Manager document.


If a label number is defined, it overrides the Project Default toggle setting as the default for the Iso Name Option. 3.

Drawing Number Option Set the Project Default toggle to either By Line ID or By Area and Line ID. — By Line ID refers to the line ID as defined in the options file. — By Area and Line ID uses the first character of the area name as a prefix to the line ID. Select the Label Number and key in a label number as it exists in the Reference Data Manager’s label description library. For more information on the label description library, refer to the PDS Reference Data Manager document. If a label number is defined, it overrides the Project Default toggle setting as the default for the Drawing Number Option.

4.

Batch Job Options These toggle switch settings define the default switch settings on the Create Batch Job Input form. Refer to Create Batch Job Input, page 5 - 89 for more information on the following toggles. — Delete Existing Files / Save Existing Files — Do Not Save Details/Save Previous Details — Submit for Plotting / Do Not Plot — Increment Revision Number/Do Not Increment Revision Number

5.

Filename Option toggle The Long Filename Available On NT Only setting allows iso filenames up to 24 characters long. This option can only be used with isos on an NT file server. If you are currently running an upgraded 6.3 project you must modify the DDL and database by performing the procedure as described in ˜/pdiso/upd_long.txt file. When set to Short Filename, the software only allows iso names up to 14 characters long.

6.

Output Path Option toggle The toggle’s default setting, Create Iso Files In Output Path, will output iso files to the main output path. Switched from the default setting, this toggle allows batch extracted isometrics to be output to a subdirectory of the main output path (see Revise Default Set, page 5 - 18 for more information on revising default output paths and other project defaults). The subdirectory is named after the area name for the line that is being extracted.

5 - 24


This setting is not unique to each default set, but is a project-wide setting.

Interactive extraction will continue to be output in the location defined in the interactive screen. 7.

Select a project default set. If a project default set is not selected, the software will fail during the extraction process.

8.

Select the accept button. The system returns to the Batch Environment form.


5.3.3 Revise Iso Area __________________________________________________________________________________________________________________________________________________ 1.

To revise an iso area, select the Revise Iso Area button from the Batch Environment form. The system displays the Revise Iso Area form with a list of available piping areas.

2.

Select an area from the list of areas. Do not select accept until all revisions have been made.

The system highlights the selected area and displays it in the appropriate Area field. 3.

Select one of the four display buttons located in the lower portion of the Revise Iso Area form. Available options are: Iso Area List

updates forms with a list of available iso areas.

Equipment Area List

lists all equipment areas available in the project. These areas are needed for equipment/nozzle information.

5 - 26


Continuation Area List

allows you to route a pipeline through multiple piping areas and show line continuation from one area to another. For example, consider a line, P-1000, that runs through areas A and B. Area A should be defined as the continuation area for area B and area B should be defined as the continuation area for area A. You may select an area only for pipeline continuation. See Intergraph Option 60 for information concerning how PD_ISO recognizes Continuation Area Data.

User Data

allows you to define up to ten user data attributes that can be mapped to the title block.

The system displays a list of available areas that correspond to the selected Area List button. If the User Data button is selected, the system displays the User Data form. To define user data, select the appropriate user data field, key in the user data and select the accept button. 4.

Select an area from the list of areas. The system displays the selected area in the appropriate Area field.

5.

Select the accept button once you have revised the iso area. The system revises the Iso Area and updates the database.


5.3.4 List Iso Areas __________________________________________________________________________________________________________________________________________________ This option displays a list of all available iso areas. Select the appropriate area(s) and select accept to confirm the selection(s).

5 - 28


5.3.5 Create Drawing __________________________________________________________________________________________________________________________________________________ The Create Drawing command allows you to create a drawing and add it to an existing iso area. 1.

Select the Create Drawing button from the Batch Environment form. The system displays the Create Drawing form.

2.

Key in a piping area name. If the contents of the Iso Area field are changed, the system clears all the remaining fields.

— OR — Select the Iso Area List button for a list of available iso areas. The system displays the List Iso Areas form.


3.

Select an iso area from the form.

4.

Select the accept button. The system returns to the Create Drawing form with the selected area displayed in the Iso Area field.

5.

Select the Type field gadget and select the appropriate isometric drawing type that will be associated with the newly-created drawing. Refer to the section Isometric Types for more information on Type.

6.

Select the Line field and key in the primary line ID, as defined in the LINE_ID_DEFINITION of the options file, of the drawing you want to create. The line ID cannot contain embedded blanks or the backslash character.

The system first checks that the line ID you key in is unique. An error message is displayed if the line ID you key in has already been defined. To view a list of currently loaded drawings, select the Drawing List button to activate the List Drawings form. The drawings are listed according to area and line ID. Once a valid line ID is entered, the system loads the appropriate information into the Drawing Number and Iso Dgn Name fields. If the Line field is changed, the system clears all the remaining fields.

5 - 30

7.


Drawing Number / Iso Dgn Name The system displays the drawing number. The contents of this field depend upon the drawing number option selected in the Define Project Options form. The system displays the isometric design file name. The design file name is used for naming subsidiary files created during the extraction. The contents of this field depend upon the iso name option selected from the Define Project Options form.

8.

Line 2 Key in a secondary line name. This line name identifies a secondary line that will be included in the drawing. The secondary line must be connected to the line identified by the primary line name. This field is optional.

9.

Line 3 Key in another secondary line ID. The same restrictions apply to Line 3 as to Line 2. This field is optional.

10.

Number of Sections This field is usually left blank. When a line leaves a piping area and then returns at some other point, such that the pipeline in the area exists in multiple disconnected sections, then the number of sections should be specified. This field allows you to treat a disconnected pipeline in the model as one line. Sheet numbering is continuous. For example, if a line exists in two sections of a model and section one generates three sheets and section two generates two sheets, then the sheets from section two will be sheets four and five of the line. This option should not be used to extract lines that are not intentionally disconnected. A line may or may not extract if you attempt to use this field to extract a pipeline not modeled correctly. The next three fields can be used as search criteria when creating batch job input. For more information on batch jobs and search criteria, refer to Create Batch Job Input, page 5 - 89 .

11.

Batch Reference Key in a batch reference number. The batch reference number allows you to group drawings within the isometric environment. If batch reference numbers are supplied, you can later specify, for example, to extract all drawings in a given area with a given batch reference number. The batch reference number is optional.


12.

Model Status Key in the model status code. The user-defined model status code helps keep track of drawing status. The following is a list of example codes: N - Line has not been modeled M - Line has been modeled but not checked C - Line has been modeled and checked A - Drawing has been extracted and approved R - Line has been revised since last approved If model status codes are defined in this field, they can be used later when generating a batch job input file. For example, you could designate that all lines in a given area be extracted with a given model status.

13.

Model Revised Date Key in a date with the format DD-MMM-YYYY. This date indicates when the lines comprising the drawing have been revised. The Model Revised Date field allows you designate for extraction, all lines that have been revised since the last drawing revision.

14.

Extraction Number The system displays the last extraction number for the drawing. The extraction number is incremented by one each time the drawing is extracted. This field could be mapped to a text node near the extraction date text node (see the description of the Extraction Date field). The extraction number helps distinguish between two drawings generated on the same day. Extraction Date The system displays the last extraction date for the drawing. The extraction date is automatically updated by the system when batch isometrics extraction occurs. This field should be mapped to a text node that lies just outside of the drawing border. This will help indicate when the drawing was generated.

Last MTO Date The system displays the date that an MTO neutral file was last generated for the drawing. The MTO date is automatically updated by the system whenever an mto neutral file is generated along with the isometric drawing.

5 - 32

15.


Sheets Generated The system displays the number of sheets generated by ISOGEN for the drawing the last time it was extracted. The number of sheets is automatically updated by the system each time the drawing is extracted.

16.

Revision block fields Rev By Chk Apv Date Ext Sht Description Each time the revision number is incremented, a new line of data is added to the revision block automatically. Line inputs are specified each time a batch job file is created.

17.

Date to Mtl Control Key in a date that indicates when the most recent MTO neutral files were passed to a material control system. This field must be manually updated.

18.

Revision Number The system displays the latest revision number of the drawing. The revision number is automatically updated by the system each time a drawing is extracted. When a batch job file is created, you indicate whether or not you want to increment the revision number during the run. If you do want to increment the number, the system increments the field by one. If the Revision Number field is initially blank, the system assumes that revision zero of the drawing is being generated.

19.

Once you have completed your inputs to the form, select the accept button. The system writes the data to the Project Control Database. The Iso Area and Line are the required minimum inputs for the Create Drawing form.


5.3.6 Revise Drawing __________________________________________________________________________________________________________________________________________________ This command activates the Revise Drawing form which allows you to revise single or multiple drawings. The first step in revising a drawing is to select the drawing(s) to be revised. Drawings can be selected by using one of two methods: Select by Line ID Select by Using Search Criteria 1.

Select the Revise Drawing button from the Batch Environment form. The system displays the Revise Drawing form.

2.

Select the Type field gadget and select the appropriate isometric drawing type. Using this option will help limit the number of drawings displayed for revision.

3.

Select either the Select By Line ID or Select Using "Search Criteria" option and follow one the following procedures to select drawings for revision.

5 - 34


Using the ‘‘Select By Line ID Option’’ to Select Drawings a.

Select the Select By Line ID option.

b.

Select the Iso Area List button for a list of available iso areas. The system displays the List Iso Areas form.

c.

Select the appropriate iso areas then select the accept button. The system displays the List Drawings form.


d.

Select individual drawings with a data point. — OR — Select all of the listed drawings by selecting the Select All button. — OR — Cancel all highlighted drawings by selecting the Reset Selections button.

e.

Select the accept button. The system returns to the Revise Drawing form with the selected drawings listed.

f.

Select the accept button and proceed to the section Revising a Single Drawing or Revising Multiple Drawings depending on the number of drawings selected for revision.

Using the ‘‘Search Criteria’’ Option to Select Drawings a.

Select the Select Using "Search Criteria" option. The system displays the Search Criteria fields on the Revise Drawing form.

b.

Select the Type field gadget and select the appropriate isometric drawing type. Using this option will help limit the number of drawings displayed for revision.

c.

Define search criteria.

5 - 36


Search Criteria: The following are search criteria that can be used separately or together to locate a drawing or group of drawings within an iso area. All defined search criteria must be met before a drawing can be included in an isometric extraction. Iso Area — Key in the name of the iso area that you want to extract lines from.

— OR —

Select the Iso Area List button. The system displays the Iso Areas form.

— Select the appropriate iso area and the accept button. The system returns to the Revise Drawing form with the selected area in the Iso Area field. If you want to restrict the list further, you must supply additional criteria such as batch reference numbers and drawing numbers. An iso area must be selected before any other search criteria can be defined.


Batch Reference Key in the batch reference number of the lines you want to extract. To use batch reference numbers as criteria, specify them in individual drawing records when adding drawing records to the Project Control Database. Model Status Code Key in the status code if you want to restrict a list to all lines of a given status. Drawing Number Low / Drawing Number High Drawing Number High and Drawing Number Low define, by drawing number, the range of lines to retrieve. Key in a drawing number in each field to identify the range of lines to extract. Model Revised Date Low / Model Revised Date High Model Revised Date Low and Model Revised Date High restricts, by model revision date, the list of lines to retrieve. Key in the model revision date in either the low or high field to restrict the list of lines. Select Subset of All Selections / Select All This toggle allows you to revise further the previously generated list of drawings. If the Select Subset of All Selections option is used, you must select one or more drawings from the list of drawings in the scroll field. If the Select All option is used, all drawings contained in the drawing list are selected. Drawings can still be unhighlighted and highlighted after this option is selected. Review a Drawing The Review a Drawing command allows you to review information on a single drawing. The Select Subset of All Selections / Select All toggle must be set to Select Subset of All Selections before selecting this command. Reset Selections The Reset Selections command allows you to reset the list of drawings to be revised.

5 - 38


Display Selections The Display Selections command allows you to view the list of drawings as it is defined by the current search criteria settings. 4.

Select the accept button. The system returns to the Revise Drawing form with the selected drawings listed.

5.

Select the accept button and proceed to the section Revising a Single Drawing or Revising Multiple Drawings depending on the number of drawings selected for revision.

Revising a Single Drawing If a single drawing is selected for revision, the system displays the Revise Single Drawing form.

a.

Revise drawing information by changing the information contained in the following fields.


Type Select the Type field gadget and select the appropriate isometric drawing type that will be associated with the drawing. Line 2 Key in a secondary line name. This line name identifies a secondary line to be extracted onto the isometric. The secondary line must be connected to the line identified by the primary line name. This field is optional. Line 3 Key in another secondary line ID. The same restrictions apply to Line 3 as to Line 2. This field is optional. Number of Sections This field is usually left blank. When a line leaves a piping area and then returns at some other point, such that the pipeline in the area exists in multiple disconnected sections, then the number of sections should be specified. This field allows you to treat a disconnected pipeline in the model as one line. Sheet numbering is continuous. For example, if a line exists in two sections of a model and section one generates three sheets and section two generates two sheets, then the sheets from section two will be sheets four and five of the line. This option should not be used to extract lines that are not intentionally disconnected. A line may or may not extract if you attempt to use this field to extract a pipeline not modeled correctly. Batch Reference Key in a batch reference number. The batch reference number allows you to group drawings within an area. If batch reference numbers are supplied, you can later specify, for example, that you want to extract all drawings in a given area with a given batch reference number. The batch reference number is optional. Model Status Key in the model status code. The user-defined model status code helps keep track of drawing status. The following is a list of example codes: N - Line has not been modeled M - Line has been modeled but not checked C - Line has been modeled and checked A - Drawing has been extracted and approved R - Line has been revised since last approved

5 - 40


If model status codes are defined in this field, they can be used later when generating a batch input file. For example, you could designate that all lines in a given area be extracted with a given model status. Model Revised Date Key in a date with the format DD-MMM-YYYY. This date indicates when the lines comprising the drawing have been revised. The Model Revised Date field allows you designate for extraction, all lines that have been revised since the last drawing revision. Date to Mtl Control Key in a date that indicates when the most recent mto neutral files were passed to a material control system. You must manually update this field. Revision Number The system displays the latest revision number of the drawing. The revision number is automatically updated by the system each time a drawing is extracted. When a batch job file is created, you indicate whether or not you want to increment the revision number during the run. If you do want to increment the number, the system increments the field by one. If the Revision Number field is initially blank, the system assumes that revision zero of the drawing is being generated. Drawing Number The system displays the active drawing number. Iso Dgn Name The system displays the isometric design file name. The design file name is used to name subsidiary files created during the extraction. The Iso design file name can be changed by selecting the Iso Dgn Name field and keying in a new name. Extraction Number The system displays the last extraction number for the drawing. The extraction number is incremented by one each time the drawing is extracted. This field should be mapped to a text node near the extraction date text node (see the description of the Extraction Date field). The extraction number helps you distinguish between two drawings generated on the same day.


Extraction Date The system displays the last extraction date for the drawing. The extraction date is automatically updated by the system when batch isometrics extraction occurs. This field should be mapped to a text node that lies just outside of the drawing border. This will help indicate when the drawing was generated.

Last MTO Date The system displays the date that an MTO neutral file was last generated for the drawing. The MTO date is automatically updated by the system whenever an MTO neutral file is generated along with the isometric drawing. Sheets Generated The system displays the number of sheets generated by ISOGEN for the drawing the last time it was extracted. The number of sheets is automatically updated by the system each time the drawing is extracted. Revision block fields Rev By Chk Apv Date Ext Sht Description Each time the revision number is incremented, a new line of data is added to the revision block automatically. Line inputs are specified each time a batch job file is created. User Data Select the User Data button to revise previously defined user data. To revise user data, select the appropriate user data field, key in the updated user data and select the accept button.

5 - 42


Select Revisions to Delete / Delete Selected Revisions When this toggle is set to Delete Selected Revisions, you can select individual revisions to be deleted. When selected, each revision is highlighted in red. When accept is selected, all red highlighted revisions are deleted. To remove red highlighting from revisions, set the toggle back to Select Revisions to Delete. Select All Revisions to Delete / Delete All Revisions When this toggle is set to Delete All Revisions, all revisions are highlighted in red. When accept is selected, all red highlighted revisions are deleted. To remove red highlighting from revisions, set the toggle back to Select All Revisions to Delete. b.

Once you have completed revising the form, select accept. The system writes the revised data to the Project Control Database and returns to the Revise Drawing form.

c.

Select exit to return to the Revise Drawing form.

Revising Multiple Drawings If multiple drawings are selected for revision, the system displays the Revise Multiple Drawings form.


a.

Revise drawing information for all of the listed drawings by changing the information contained in the following fields. A key-in in any of the following fields, followed by the accept button, will result in an update of all drawings listed in the scroll area.

Type Select the Type field gadget and select the appropriate isometric drawing type that will be associated with the drawing. Number of Sections This field is usually left blank. When a line leaves a piping area and then returns at some other point, such that the pipeline in the area exists in multiple disconnected sections, then the number of sections should be specified. This field allows you to treat a disconnected pipeline in the model as one line. Sheet numbering is continuous. For example, if a line exists in two sections of a model and section one generates three sheets and section two generates two sheets, then the sheets from section two will be sheets four and five of the line. This option should not be used to extract lines that are not intentionally disconnected. A line may or may not extract if you attempt to use this field to extract a pipeline not modeled correctly. Batch Reference Key in a batch reference number. The batch reference number allows you to group drawings within an area. If batch reference numbers are supplied, you can later specify, for example, that you want to extract all drawings in a given area with a given batch reference number. The batch reference number is optional. Model Status Key in the model status code. The user-defined model status code helps keep track of drawing status. The following is a list of example codes: N - Line has not been modeled M - Line has been modeled but not checked C - Line has been modeled and checked A - Drawing has been extracted and approved R - Line has been revised since last approved If model status codes are defined in this field, they can be used later when generating a batch job. For example, you could designate that all lines in a given area be extracted with a given model status.

5 - 44


Model Revised Date Key in a date with the format DD-MMM-YYYY. This date indicates when the lines comprising the drawing have been revised. The Model Revised Date field allows you designate for extraction, all lines that have been revised since the last drawing revision. Date to Mtl Control Key in a date that indicates when the most recent mto neutral files were passed to a material control system. You must manually update this field. Revision Number The system displays the latest revision number of the drawing. The revision number is automatically updated by the system each time a drawing is extracted. When a batch job file is created, you indicate whether or not you want to increment the revision number during the run. If you do want to increment the number, the system increments the field by one. If the Revision Number field is initially blank, the system assumes that revision zero of the drawing is being generated. Revision block fields Rev By Chk Apv Date Ext Sht Description Each time the revision number is incremented, a new line of data is added to the revision block automatically. Line inputs are specified each time a batch job file is created. User Data Select the User Data button to revise previously defined user data. To revise user data, select the appropriate user data field, key in the updated user data and select the accept button. Delete Revision Record(s) Select the Delete Revision Record(s) button to delete all of the revision history entries. After selecting this option, the system prompts: Accept to delete all records. Select the accept button to delete the records.


b.

Once you have completed revising the form, select accept. The system writes the revised data to the Project Control Database and returns to the Revise Drawing form.

c.

Select exit to return to the Revise Drawing form.

5 - 46


5.3.7 Delete Drawing __________________________________________________________________________________________________________________________________________________ This command activates the Delete A Drawing form that allows you to delete single or multiple drawings. The first step in deleting a drawing is to select the drawing(s) to be deleted. Drawings can be selected by using one of two methods: Deleting a drawing will also delete any associated files that were created in the output location as defined in the default set. Select by Line ID Select by Using Search Criteria 1.

Select the Delete Drawing button from the Batch Environment form. The system displays the Delete A Drawing form.

2.

Select the Type field gadget and select the isometric drawing type that is associated with the drawing.


3.

Select either the Select By Line ID or Select Using "Search Criteria" option and follow one the following procedures to select drawings for revisement.

Using the ‘‘Select By Line ID’’ Option to Select Drawings a.

Select the Select By Line ID option.

b.

Select the Type field gadget and select the one of the isometric drawing types. Using this option will help limit the number of drawings displayed for deletion.

c.

Select the Iso Area List button for a list of available iso areas. The system displays the List Iso Areas form.

d.

Select the appropriate iso areas then select the accept button. The system displays the List Drawings form.

5 - 48

e.


Select individual drawings with a data point. — OR — Select all of the listed drawings by selecting the Select All button. — OR — Cancel all highlighted drawings by selecting the Reset Selections button.

f.

Select the accept button. The system returns to the Delete A Drawing form with the selected drawings listed.

g.

Select the accept button and proceed to the section Deleting a Single Drawing or Deleting Multiple Drawings depending on the number of drawings selected for revisement.

Using the ‘‘Search Criteria’’ Option to Select Drawings a.

Select the Select By "Line ID" option. The system displays the Search Criteria fields on the Delete A Drawing form.


b.

Select the Type field gadget and select the appropriate isometric drawing type. Using this option will help limit the number of drawings displayed for deletion.

c.

Define search criteria.

Search Criteria: The following are search criteria that can be used separately or together to locate a drawing or group of drawings within an iso area. All defined search criteria must be met before a drawing can be included in an isometric extraction. Iso Area — Key in the name of the iso area that you want to extract lines from.

— OR —


5 - 50


— Select the appropriate iso area and the accept button. The system returns to the Delete A Drawing form with the selected area in the Iso Area field. If you want to restrict the list further, you must supply additional criteria such as batch reference numbers and drawing numbers. An iso area must be selected before any other search criteria can be defined. Batch Reference Key in the batch reference number of the lines you want to extract. To use batch reference numbers as criteria, specify them in individual drawing records when adding drawing records to the Project Control Database. Model Status Code Key in the status code if you want to restrict a list to all lines of a given status. Drawing Number Low / Drawing Number High Drawing Number High and Drawing Number Low define, by drawing number, the range of lines to retrieve. Key in a drawing number in each field to identify the range of lines to extract.


Model Revised Date Low / Model Revised Date High Model Revised Date Low and Model Revised Date High restricts, by model revision date, the list of lines to retrieve. Key in the model revision date in either the low or high field to restrict the list of lines. Select Subset of All Selections / Select All This toggle allows you to revise further the previously generated list of drawings. If the Select Subset of All Selections option is used, you must select one or more drawings from the list of drawings in the scroll field. If the Select All option is used, all drawings contained in the drawing list are selected. Drawings can still be unhighlighted and highlighted after this option is selected. Review a Drawing The Review a Drawing command allows you to review information on a single drawing. The Select Subset of All Selections / Select All toggle must be set to Select Subset of All Selections before selecting this command. Reset Selections The Reset Selections command allows you to reset the list of drawings to be deleted. Display Selections The Display Selections command allows you to view the list of drawings as it is defined by the current search criteria settings. 4.

Select the accept button. The system returns to the Delete A Drawing form with the selected drawings listed.

5.

Select the accept button and proceed to the section Deleting a Single Drawing or Deleting Multiple Drawings depending on the number of drawings selected for revisement.

Deleting a Single Drawing If a single drawing is selected for deletion, the system displays the Delete A Drawing form that contains drawing information for the selected drawing.

5 - 52


If you have never extracted the displayed line with the Increment Revision No toggle option (see Create Batch Job Input, page 5 - 89 for more information), only the database drawing record will be deleted. The isometric file will not be deleted. The system will display a warning message box if this situation occurs. a.

Select the accept button to delete the displayed drawing. The system deletes the drawing and returns to the Delete A Drawing form.

Deleting Multiple Drawings If multiple drawings are selected for deletion, the system returns to the Delete A Drawing form which contains a listing of the selected drawings.


If any of the lines selected for deletion have never been extracted using the Increment Revision No toggle option (see Create Batch Job Input, page 5 89 for more information), only the database drawing records will be deleted. The isometric files will not be deleted. The system will display a warning message box if this situation occurs. a.

Select the accept button to delete the displayed drawings.

5 - 54


5.3.8 List Drawings __________________________________________________________________________________________________________________________________________________ This command allows you to list all drawings within a piping area. 1.

Select the List Drawings command from the Batch Environment form. The system displays the Drawing List form.

2.

Key in the piping area that contains the drawings you want to list. — OR — Select the Iso Area List button for a list of available iso areas. The system displays the List Iso Areas form.


— THEN — Select an iso area from the form and select the accept button. The system returns to the List Drawing form with the selected area displayed in the Iso Area field. The system displays the drawings that are within the selected piping area. If the area does not exist, the system displays an error message.

5 - 56


5.3.9 Utilities __________________________________________________________________________________________________________________________________________________ Utilities options are used to simplify building and maintaining the Project Control Database and in defining areas and drawing information. 1.

Select the Utilities button from the Batch Data Environment form. The system displays the Utilities form.


5.3.9.1 Bulk Load Lines __________________________________________________________________________________________________________________________________________________ The Bulk Load Lines command allows you to load multiple lines by defining a specific model, area or group of line numbers. 1.

Select the Bulk Load Lines button from the Utilities form. The system activates the Bulk Load Lines Form.

2.

Select the Iso Type field gadget and select the appropriate isometric drawing type that will be loaded. Refer to Isometric Types, page 21 - 1 for more information on Iso Type.

3.

Key in a Default Batch Reference Number. This field input is optional.

4.

Set the Iso Name Option toggle to the appropriate setting. Select the By Project Default setting (By Line Id or By Area and Line ID) to use the project default set previously defined on the Isometric Extraction Project Options form. For more information on defining the project default set, see Define Project Options, page 5 - 22 .

5 - 58


Select the By Label Number setting to use the label number previously defined on the Isometric Extraction Project Options form. For more information on defining the project default set, see Define Project Options, page 5 - 22 . Label number refers to the label number as it exists in the Reference Data Manager’s label description library; not the label library referred to in the Files section of the ISOGEN options file. 5.

Set the Drawing Number Option toggle to the appropriate setting. Select the By Project Default setting (By Line Id or By Area and Line ID) to use the project default set previously defined on the Isometric Extraction Project Options form. For more information on defining the project default set, see Define Project Options, page 5 - 22 . Select the By Label Number setting to use the label number previously defined on the Isometric Extraction Project Options form. For more information on defining the project default set, see Define Project Options, page 5 - 22 . Label number refers to the label number as it exists in the Reference Data Manager’s label description library; not the label library referred to in the Files section of the ISOGEN options file.

6.

Select the Default Set field to select another default set from the Isometric Extraction Default Sets form.

Select a default set from the form and select the accept button to return to the Bulk Load Lines form.


7.

Select one of the following methods of bulk loading lines. creates drawing records for all pipelines in a selected Iso Area.

creates drawing records for all pipelines in a selected Iso Model.

creates drawing records for selected pipelines within a selected Iso Model.

5 - 60


Load by Area

__________________________________________________________________________________________________________________________________________________

After the Load by Area button is selected, the system activates the Bulk Load Lines form and prompts you to select the area(s) that contain the lines to be loaded.

1.

Select the appropriate area(s) and select the accept button. The system loads all lines associated with the selected area(s) and the area definition if it does not currently exist. The following form will be displayed if the ISOGEN software detects any invalid lines. An invalid line occurs when any attribute value defined in the LINE_ID_DEFINITION section of the option file is left blank.


The invalid iso line information, appended with the current time, is saved into /usr/tmp/ld*****.log after all valid iso lines have been processed. The invalid iso line log file will be appended to until the Bulk Load Lines command is exited.

5 - 62


Load by Model

__________________________________________________________________________________________________________________________________________________

After the Load by Model button is selected, the system activates the Bulk Load Lines form and prompts you to select an area.

1.

Select the area that contains the appropriate models. The system updates the form by displaying a list of available iso models that reside within the selected iso area.


2.

Select the appropriate iso model(s) and select the accept button. The system loads all lines associated with the selected model(s). The following form will be displayed if the ISOGEN software detects any invalid lines. An invalid line occurs when any attribute value defined in the LINE_ID_DEFINITION section of the option file is left blank.


5 - 64


Load by Line

__________________________________________________________________________________________________________________________________________________

After the Load by Line button is selected, the system activates the Bulk Load Lines form and prompts you to select an area.

1.

Select the area that contains the appropriate model. The system updates the form by displaying a list of available iso models that reside within the selected iso area.


2.

Select the appropriate iso model and select the accept button. The system updates the form by displaying a list of available iso lines that reside within the selected iso model.

3.

Select the appropriate iso line(s) and select the accept button. The system loads all selected lines. The following form will be displayed if the ISOGEN software detects any invalid lines. An invalid line occurs when any attribute value defined in the LINE_ID_DEFINITION section of the option file is left blank.

5 - 66




5.3.9.2 Bulk Load Lines from ASCII File __________________________________________________________________________________________________________________________________________________ Since this command does not create ISOGEN areas, the ISOGEN area you are loading lines into must exist before running this command. For more information on creating a 3D piping/ISOGEN area, refer to the section Creating 3D Areas and Models in the PDS Project Setup Technical Reference. 1.

Select the Bulk Load Lines From ASCII File button. The system activates the Bulk Load Lines From ASCII File form.

2.

Key in the filename which contains the pipeline information to be loaded. If the export statement is defined in the control shell, the above field will be loaded automatically. For example: export ISO_ASCII_LOAD=/pdssk:/usr/50cert The system generates a log file using the system filename with a .log file extension. This file contains error or warning messages and also information about which areas and lines, if any, have been added to the database.

5 - 68

3.


Select the accept button. The system checks the file for syntax errors and undefined areas. If no errors are detected, the system adds the lines to the existing ISOGEN areas (as defined in the ASCII file) and returns to the Bulk Load Lines From ASCII File form. If no errors are detected, but warnings occur, the system displays the warning messages and adds the areas and their respective lines to the database. If any errors are detected, the system displays the errors and any warnings, and does not update the database. The following steps are only used when warnings and/or errors are detected during the loading process.

4.

Revise File Select the Revise File button to edit the current file using the default editor. The system creates an editor window based on the text editor defined by the PDEDITOR export variable in the control shell.


The following is an example of a typical ASCII file: Projectname

! required - must be 1st line, 1st column

Begin Area IsoAreaName #E EquipmentContArea #C PipeContArea #Un "Area User Data"

! required - Begin Area 1

required optional - up to 5 optional - up to 10 optional - data must be between double quotes - where n is a number: 1 - 10 "IsoType" ! optional literal string double quotes LineId ! required #L2 LineId2 ! optional #L3 LineId3 ! optional #S NumSections ! optional #B BatchRefNum ! optional #M ModelStatusCode ! optional #Un "Drawing User Data" ! optional - data must be between double quotes - where n is a number: 1 - 10 "IsoType" ! optional literal string double quotes LineId ! required #L2 LineId2 ! optional #L3 LineId3 ! optional #S NumSections ! optional #B BatchRefNum ! optional #M ModelStatusCode ! optional #Un "Drawing User Data" ! optional - data must be between double quotes - where n is a number: 1 - 10 End Area ! required - End Area 1 Begin Area PIPE01 AF7701PQ End Area

! ! ! !

! ! ! !

Begin Area 2 Iso Area Name Line ID End Area 2

If Iso Type is not defined, ISOGEN defaults to Fabrication. Refer to Isometric Types, page 21 - 1 for more information on Iso Type. Where the keyword: Begin Area End Area #E #C #Un #L2 #L3 #S #B #M !

is the beginning of an area record. is the end of area record. is the continuation equipment areas. is the continuation pipe areas. is user data and a number 1 - 10. is LineId 2. is LineId 3. is the number of sections. is the batch reference number. is the model status code. is a comment line The keywords listed above must precede any information they are associated with. For example, a batch reference number called steam unit would have to appear in the ASCII file as: #B STEAM_UNIT.

5 - 70


No spaces are allowed between the # and the letters. KEYWORDS are not case sensitive. For example, Begin Area = BEGIN area = BEGIN AREA, #E = #e User data, #Un, must be enclosed in double quotes. Tabs, spaces and blank lines are allowed anywhere within the file. The project name will be used as a check to verify that the file belongs to the current project. The project name must be on the first line in the first column. Comments may be included on any row by using a !. Anything after the ! up to a newline is considered part of the comment. 5.

Process another file Select the Process another file button to dismiss the displayed warning/error messages and display the Filename and Log Filename fields. Return to step 2.

6.

Process "Areas With No Syntax Errors" Select the Process "Areas With No Syntax Errors" button to continue processing areas that have the correct syntax.


5.3.9.3 Isometric Symbol Editor __________________________________________________________________________________________________________________________________________________ ISOGEN provides an extensive library of symbols that you can select to map PDS symbol names to isometric drawing symbols. If the drawing symbology for some of these symbols is inadequate, you can redefine them to have new symbology. It is recommend that you copy the provided design files and index files when creating new symbols. These files are the symbol.dgn and symbol.ndx files that are located in the directory ˜/pdiso/dat. The symbol definition process consists of the following steps: 1.

Draw the symbol in graphics by using the Symbol Definition Software.

2.

Create a symbol library from the graphics generated in step 1.

3.

Add the symbol library to the options file.

4.

Change the PDS to ISOGEN symbol map, as needed, so that PDS items are mapped to the appropriate ISOGEN SKEY.

The working units of the copied symbol.dgn file are defined as the following:

Master Units : M Sub Units : MM sub units per master unit: 1000 uor per sub unit : 1000

The Data readout accuracy is set to .02. The scale and angle locks and grid display may be turned ON to make symbol construction easier. The following grid setup works well and can be saved using the MicroStation file designed option: GU=0: .10 GR=10

5 - 72


Entering the Iso Symbol Editor Environment

__________________________________________________________________________________________________________________________________________________

1.

Select the Iso Symbol Editor button from the Utilities form. The system displays the Isometric Symbol Editor form.

2.

Define the Symbol Design, Symbol Index and Symbol Library fields to define the location of those files. Use the format nodename:path to define the location of each file. For example: mynode:/usr/ip32/pdiso/dat/symbol.dgn. You can set the PDS Environment Variables: SYMDGN, SYMNDX and SYMLIB to define default values for these fields. You can key in the name of a previously-created, symbol index file name by two methods. You can key in the name when revising a symbol that has been defined in a previous session. Also, you can key in the name when adding a new symbol to a 2-D design file that already contains one or more user-defined symbols.


If a single index file is not maintained for each design file that contains user-defined symbols, you will have difficulty converting the design file graphics into an ISOGEN symbol library. It is recommended that all symbols be defined in one design file with one corresponding index file. 3.

After defining the fields in the previous step, select the Symbol Editor button to enter the MicroStation environment and activate the Isometric Symbol Definition form.

Input Area Options

__________________________________________________________________________________________________________________________________________________

Various components of the isometric symbol can be created and/or revised using the commands in the Input area and the Symbol Origin command located on the Isometric Symbol Definition form.

Old Skey Select the Old Skey field, and key in an old skey for the symbol you are defining. The old skey is an existing symbol key chosen from Appendix B: Alias ISOGEN Tables. When defining a new symbol, some of the default properties of the new symbol are inherited from the old one. The basic skeleton or connect point geometry of a new symbol may not vary from that of the old symbol. For example, you must not define a new angled fitting based on a straight-through fitting.

5 - 74


New Skey Select the New Skey field, and key in a new skey. The new skey is the symbol key of the symbol that is currently being defined. The following notes apply to new skey: If you leave the new skey blank, the old symbol will be redefined. If the old skey is variable end prep (that is, the old skey ends with the characters **), the symbol will be redefined for all end preps. If the old skey is specified with a specific end prep, only the symbol with that end prep will be redefined. If you specify a new skey, a new symbol of that name will be created. The new skey may end with the characters ** to indicate that the symbol is variable end prep. If the old skey is a valve operator and the new skey is left blank, all valve symbols that currently use that operator symbol will be redefined with the new operator. If the old skey is a valve operator and a new skey is specified, the operator must be explicitly attached to new valve symbols (using the spindle key input field). The new skey must never be the same as one of the old skeys that have been previously defined for ISOGEN. The system checks the index file to see if the current combination of old and new skey already exists. — THEN — If the combination exists, the software recognizes that an existing user-defined symbol definition is being revised. The software will then perform a window area about the redefined symbol graphics that you previously placed in the design file. — OR — If the combination does not exist in the index file, the software knows that the symbol is being redefined for the first time.

Symbol Origin If you are revising an existing iso symbol, do not define a symbol origin.

The Symbol Origin command defines an area in which the new iso symbol will be created. All iso symbol graphics must be contained within the defined area. Select the Symbol Origin button from the Isometric Symbol Definition form. The symbol origin is the lower left hand corner of a rectangular area in which the new symbol will be drawn. The rectangular area is approximately 20 x 25 mm.


Position the rectangular area and place a data point to place it. Once the area is placed, you must draw the iso symbol using only MicroStation Line and Linestring commands. No circles or closed shapes can be used. Keep the symbol as simple and as symmetrical as possible. Use approximately one-fourth of the block for the right proportion of your new symbol. Do not move or change the area once it is placed.

Spindle Key Spindle Key defines the operator subsymbol that will be attached to this symbol when it is drawn in the isometric. There are 12 existing spindle keys defined in the table in Appendix B: Alias ISOGEN Tables. You can also define new spindles (operators). If the symbol does not require a spindle, this field can be left blank if the symbol does not require a spindle.

ScaleFactor ScaleFactor is used to scale the plotted shape up or down relative to the dimensions used in drawing the symbol. A value of 100 (which is recommended) will give a scaling factor of 1.

Orientation Orientation is used to define the type of fitting drawn. This number is used for automatically creating a mirror image symbol. Available options include: Symmetrical - none (symbol is symmetrical) Flow Direction Dep - flow direction dependent (for example, check valve) Large to Small Bore - large to small bore (for example, reducer) Flange Start - flange start (for example, has a gasket to the left)

Flow Arrows Flow Arrows defines the flow arrow for the symbol. Available options include: Use Old SKEY - same as the old skey No - never has a flow arrow Yes - has a flow arrow

Dimensions Dimensions control how the fitting or symbol is dimensioned. Available options include: Use Old SKEY - same as the old skey Off - dimensions off On - dimensions on

5 - 76


Lagging/Tracing Lagging/Tracing controls the insulation and heat tracing display on the fitting. Available options include: Use Old SKEY - same as old skey Both Off - both off Lagging On - lagging on Tracing On - tracing on Both On - both on Setting values in option block words 61 and 62 causes ISOGEN to draw insulation and tracing on every component. These symbols definition options enable you to override the options block switches. For example, even though insulation and tracing on components are enabled, the previous options allow you to specify that for a specific component neither value should be displayed.

Assembling an Isometric Symbol

__________________________________________________________________________________________________________________________________________________

The different components that make a user-defined isometric symbol include: Symbol Origin

Dynamically displays a drawing symbol area (discussed previously).

Start Point

The in point of the symbol; analogous to a connect point in PDS terminology. The point where the symbol will connect to adjacent symbols.

End Point

The out point of the symbol. Also, a point where the symbol will connect to an adjacent symbol.

Spindle Point

The point where a valve operator attaches to a symbol. Similar to the symbol origin in the PDS world.

Tap Points

Branch points on a symbol. Points where other piping components can be attached to the symbol. Tap points are not exactly analogous to PDS taps. A redefined symbol will usually have several tap points; however, when a drawing is created normally, only one or two will be used.

Symbol

Symbol graphics consist of the lines and line strings that are always drawn when a symbol is drawn in a drawing.

Lagging

Lagging graphics consist of the lines and line strings that are only drawn when the lagging on the symbol is enabled.

Tracing

Tracing graphics consist of the lines and line strings that are only drawn when the heat tracing on the symbol is enabled.


The following are guidelines that should be used when assembling components into a symbol. 1.

In this example, the symbol is created in a coordinate system where the x-axis is horizontal and the y-axis is vertical. The origin of the coordinate system should fall on a point of symmetry of the symbol. Thus, the y-axis will bisect the symbol. The symbol start point will usually fall on the x-axis.

2.

The only valid connect point geometries that you can define are the following: End point (for example, caps, plugs, blind flanges) Straight through (for example, valves, flanges) Offset (for example, eccentric reducer, flange) 90 degree change of direction (for example, angle valve) 3-way (for example, 3-way valve) 4-way (for example, 4-way valve) Other geometries must be obtained through the use of fitting taps. This requirement impacts the definition of symbols in the PDS environment. When defining a symbol in PDS, you must consider the ISOGEN symbol to which you will map when selecting the connect point geometry. If any connect point geometry does not map to an ISOGEN connect point geometry, extraction will not be performed properly. Example: In this example, a specialty item that resembles a lateral needs to be defined in both PDS and within ISOGEN, so that it properly extracts to a drawing. Appendix B states that no symbols exist with connect point geometry that satisfies the requirements of the speciality item. (In fact, you can map the specialty item to a TEXX (which is a tee); however, the symbology for a TEXX is not acceptable, and the TEXX can not be redefined.) In one solution, you can define the basic connect point skeleton of the item in both PDS and ISOGEN as a straight-through component. Although, the branch off the side can be a tap, you can not draw graphics that extend from the ISOGEN symbol for the branch. This is because you can not force ISOGEN to use a specific tap on the iso symbol. You must define several tap points and allow ISOGEN to choose the one that gives the best graphic representation of the component and connecting piping.

3.

When defining graphics that are drawn between the end prep symbols, your symbol definition should not contain any end prep graphics.

4.

When defining an offset fitting, the flow should go from top left to bottom right in the symbol coordinate system. For example, an eccentric reducer would be drawn with the large end on the left and the small end on the right, with the flat side down or at the bottom of the symbol. Flanged offset fittings must be created with the end prep graphics drawn integrally with the symbol.

5 - 78

5.


If angled fittings consist of two or more legs, all legs of a redefined angled fitting must be identical. When you define the angled fitting, you draw only a single leg. The other legs are created automatically by ISOGEN. The leg that you draw must be symmetrical about the x-axis of the symbol coordinate system. The start point of the leg must be to the left of the y-axis and the end point must be the pivot point or the origin of the symbol. All legs of an angled fitting must have a common pivot point (this requirement excludes redefinition of symbols like the angle block BA**).

Allowable and unallowable angled shapes 6.

A symbol can have up to nine tap points. When distributing tap points, observe the following rules. No more than three tap points can be placed on the x axis. No more than three tap points can be placed on the y axis. No more than three tap points can be placed above the x axis. No more than three tap points can be placed below the x axis. No more than three tap points can be placed left of the y axis. No more than three tap points can be placed right of the y axis. The previously-listed rules are not checked during symbol creation, but are verified when the symbol is written to the symbol library. The symbol will not be written if any of the limits are exceeded. To use tap points that are not on the x or y axis, when the symbol is drawn, observe the following rules: Outer tap points in the y-axis direction must be located at least 5 mm from the yaxis if they are to be used. Outer tap points in the x-axis direction must be located by at least the greater of 5 mm or 10% of the symbol length down the x-axis if they are to be used.


When a component with taps in the model is mapped to a symbol without taps, the tap point is assumed to be at the center of the symbol. None of the default ISOGEN symbols have defined tap points. A symmetrical symbol should have symmetrically distributed tap points so that ISOGEN always finds an appropriate tap point no matter how the symbol is oriented in a drawing.

Tap points on a flange 7.

Redefined symbols can not be too large. Otherwise, problems may occur with graphic interferences within the drawings. The amount of space reserved in a drawing for a symbol is always based on that of the old skey. Therefore, you should keep your symbol approximately the same size as the one it is based on. Using this criteria, most symbols should be between 8 and 12 mm long and 4 to 8 mm tall. Sketches of several of the original ISOGEN symbols appear in Appendix E: ISOGEN SKEY Dimensions.

8.

In redefining a valve operator symbol, you must follow these rules: The start point of the symbol must be the point where the operator attaches to the valve. The operator must be defined on its side with the stem lying along the x-axis and the handwheel lying along the y-axis.

9.

Two alternatives exist for defining pipe supports: The pipe support symbol does not have an orientation (like the default ISOGEN pipe support symbol). In this case, the start and end points of the symbol should be located at the same point. The graphics should be symmetrical about the xaxis.

5 - 80


The pipe support symbol has an orientation much like a valve operator does. In this case, the symbol definition should take place in two steps. — Redefine the pipe support so that it consists of only a start point, an end point, and a spindle point all located at the same place. The spindle key for this pipe support should be set so that a valve operator is attached when the symbol is placed. — Define the valve operator that will actually be the pipe support graphics. With these guidelines, you should select commands from the tutorial and locate the various symbol components. Each tutorial command is described in the following sections.

Start Point You use this command to specify the start point of the symbol. After you select the command, you must identify the point with either a data point or an XY= key-in. A symbol must contain one and only one start point. You can use the MicroStation view manipulation commands while drawing the symbol graphics. You must cancel out of view commands, however, before making subsequent tutorial selections. You can use the MicroStation element manipulation commands to modify graphics that you place to build the symbol. The system responds by placing a heavy cross at the point you specify.

End Point Use this command to define the end point of the symbol. After you select the command, you must identify the point with either a data point or an XY= key-in. A symbol must contain one and only one end point. The system responds by placing a heavy cross at the point you specify.

Fit Symbol Command The Fit command is used to perform a fit operation on the symbol definition area. Select the Fit command and place a data point in the view to fit the symbol. The system responds by doing a window area about the box that encompasses the current symbol definition.


Solid Line Select this command just prior to drawing symbol graphics with the MicroStation place line and place linestring commands. Symbol graphics can consist of lines and linestrings only. The system responds by setting the line code to solid.

Lagging Select this command just prior to drawing insulation graphics using the MicroStation place line and place linestring commands. Insulation graphics can consist of lines and linestrings only. The system responds by setting the line code to long dash.

Tracing Select this command just prior to drawing heat tracing graphics using the MicroStation place line and place linestring commands. Heat tracing graphics can consist of lines and linestrings only. The system responds by setting the line code to dot dash.

Spindle Point Use this command to define the spindle point of the symbol. After selecting this command, you must identify the point with either a data point or an XY= key-in. A symbol can contain only one spindle point. The system responds by placing a heavy cross at the point you specify.

Tap Points Use the Tap Points command to define tap points on the symbol. After you select this command, identify a point with either a data point or an XY= key-in. A symbol can contain up to 9 tap points. The system responds by placing a heavy cross at the point you specify.

Accept Choose Accept to indicate that the symbol definition is complete. The system responds by checking your definition to confirm that it contains a start point and end point. The system then adds a new record to the symbol index file.

5 - 82


Clear Command Choose Clear to stop work on the current symbol and reinitialize the tutorial. The system responds by erasing all tutorial inputs and a fit operation is performed on the design file.

Delete Command Choose Delete to delete the current symbol. The system responds by deleting all of the symbol graphics and any record that may have been written to the symbol index file.

Exit Select the Exit command when you are finished redefining symbols. The system responds by closing the symbol index file and deactivating the symbol definition tutorial.


Creating a User-defined Symbol Library

__________________________________________________________________________________________________________________________________________________

After drawing the symbol graphics with the Symbol Definition Software, you must generate a symbol library. To create the symbol library, select the Update Symbol Library button from the Isometric Extraction Utilities form.

Before Using This Command You must have created a design file containing user-defined symbols, and you must also have the corresponding symbol index file. The system performs the following processes when updating the symbol library. The system verifies that the symbol file (defined in the Isometric Symbol Editor Screen form) exists. If the file does not exist, the system displays an error message and returns to the Isometric Symbol Editor Screen form. The system verifies that the index file (defined in the Isometric Symbol Editor Screen form) exists. If the file does not exist, the system displays an error message and returns to the Isometric Symbol Editor Screen form. The system displays the following messages at the start of each phase of processing. Stroking design file contents... Converting ASCII symbols to binary... Upon completion, the system prompts Symbol library successfully created If any errors are encountered during processing, refer to the log file that is written to the ˜/pdiso/dat directory.

5 - 84


Using the Newly-created Symbol Library

__________________________________________________________________________________________________________________________________________________

To use the newly-created symbol library, you must first perform three actions: 1.

Edit the options file, and add the binary symbol library file name to the FILES table. Refer to The Options File, page 7 - 1 for more information on the FILES table.

2.

Edit the NEW_SYMBOL_KEYS table in the options file where necessary. Refer to The Options File, page 7 - 1 for more information on the NEW_SYMBOL_KEYS table.

3.

Modify the PDS to ISOGEN symbol map so that PDS symbols map to the newly-defined ISOGEN symbols.


5.3.9.4 Delete Drawing Records With Undefined Iso Type __________________________________________________________________________________________________________________________________________________

This command deletes all isometric drawings that do not have an associated Type (fabrication, Spool, etc.). If you need to assign a Type to a drawing, one can be assigned by using the Revise Drawing command. All records that have been written to pdtable_185 in the project database must have an assigned iso Type or they cannot be extracted.

5 - 86


5.3.9.5 Generate FrameWorks Reference Dimension File __________________________________________________________________________________________________________________________________________________ The FrameWorks Reference Dimension File command allows you to generate an ASCII file that is used by Intergraph option 71 to place reference dimension in the isometric drawing. For more information on Intergraph option 71 refer to the section, The Options File. Structural elements are placed in FrameWorks Plus by using one of ten available cardinal points. Each cardinal point represents a different point on the cross-section of a structural member. For example, an I-beam can be placed using cardinal point 5 (CP5)which is the center of its cross section or it can be placed by CP6 the right-center point on the beam’s cross-section. The choice of cardinal point takes on additional relevance when using the Isometric Column Reference (Intergraph option 71) because this is the point that the pipeline will use as a reference.

In the previous graphic, the same pipeline is extracted twice. In the top extraction, column C_25 was placed using CP5 (center-center) while the bottom extraction was placed using CP6 (right-center). In both cases, the referenced column is in the same physical location and the position of the pipeline is unchanged. However, note that the easterly dimension varies by half the thickness of the column. Since the Structural Column Reference option (Intergraph option 71) references structural elements according to their active cardinal point at the time of placement. It is highly recommended that structural columns be placed by CP5 (center-center).

1.

Select the Frameworks Reference Dimension File button from the Isometric Extraction Utilities form.


The system activates the Create Reference Dimension File form.

The information in the FrameWorks ASCII Data Filename and the Log Filename fields is for display purposes only. The fields display the nodename and location to which the dimension file and log file will be written. 2.

Select the Batch Queue pulldown gadget and select the queue that will be used to generate the dimension file.

3.

Set the Submit Batch Immediately/Delay Batch Submit Time toggle. Select the Submit Batch Immediately option to run the job immediately. Select the Delay Batch Submit Time to specify a run time for the job. Define the run time by keying in the day of the week (Mon, Tue, etc.), the time and then select AM or PM.

5 - 88

4.


After the Batch Queue and the Submit Batch toggle have been set, select the accept button. The system generates the FrameWorks ASCII Data file and log file.


5.3.10 Create Batch Job Input __________________________________________________________________________________________________________________________________________________ To extract isometrics using the batch software, you must create a batch job input file. The batch job file is an ASCII data file that is submitted to the batch extraction software as an input file. You create the batch input file by identifying which lines to create drawings for and setting the options that determine how the job will be processed. Lines can be selected for the batch input file using one of two methods. These include defining search criteria to select large groups of lines and selecting lines by line ID. Once a batch input file is created, it can be scheduled by using the Schedule Batch Job command. Refer to Schedule Batch Job, page 5 - 100 for more information. 1.

Select the Create Batch Job Input button from the Batch Environment form. The system displays the Create Batch Job Input form. When the accept button is selected on this Create Batch Job Input form, line ID records will be written to the batch job input file using this form’s current search criteria. Be sure that you do not select accept on this form unless you have set the appropriate search criteria. Select cancel (X) to exit the form without writing line records.

5 - 90

2.


Batch Job Input File Key in the batch job input file name. If a file name is not keyed in, the system options to the exported variable ISOBATCH. The system checks that the existing file is a valid batch job input file and that it was generated from the same Project Control Database.

If the file already exists the system will display the Overwrite, Append and Review/Edit buttons. Select the Overwrite to overwrite the batch input file or select Append to append the information to the existing batch input file information. Select Review/Edit to display the batch input file in the default editor. The default editor is notepad. You can use the export variable PD_EDITOR to define a different default editor. 3.

Default Set Option Select the Default Set Option field to select another default set from the Isometric Extraction Default Sets form.


Select a default set from the form and select the accept button. The system returns to the Create Batch Job Input form and displays the selected default set and description in the Default Set Option field. 4.

Delete Existing Files / Save Existing Files toggle If the Delete Existing Files option is selected, the system will overwrite all miscellaneous files that were created as a result of a previous isometric generation. These files include any ISOGEN output you have enabled using the options file and error message files produced by the ISOGEN software. If the Save Existing Files option is selected, the system will not delete any of the generated miscellaneous files. This toggle will not purge old versions of the MTO neutral files. The batch extraction software uses the extraction number to name the neutral files. Example: The MTO neutral file is named as follows: iso name + sheet number + .b + extr number So, a MTO file named CW10022.b7 is the MTO neutral file for iso CW1002, sheet 2, from extraction number 7. As shown in the above example, the MTO neutral file generated by the ISOGEN interface is split up into multiple files by the batch extraction software. Each new MTO file contains the material associated with a single isometric drawing sheet.

5 - 92


If you choose not to delete the existing files, the existing iso will be copied to "output path"/isolast/. 5.

Do Not Save Details/Save Previous Details toggle If the Do Not Save Details option is selected, the system ignores any previously added graphics. If the Save Previous Details option is selected, the system adds all manually added MicroStation graphics of the previous isometric drawing version to the new version. Before using the Save Previous Details option, the MicroStation file, edg.exe, must be loaded locally to the workstation that will be used to process the isometric drawings. The software looks in the output directory (as specified in the area level data) for each drawing sheet as it is produced. If a drawing sheet is found, then all graphics that reside on levels 61 through 63 are merged into the new version of the drawing. This allows you to add manual details that will be retained from version to version of the drawing. Some changes, particularly those made to the isometric drawing itself, will not be acceptable or correct when merged into a new version of the drawing.

6.

Submit for Plotting / Do Not Plot toggle If the Submit for Plotting option is selected, the selected isometric drawings will be submitted for plotting. A Plot Request file name must be specified in the default set. For more information, see Define Default Sets, page 5 - 13 . If the Do Not Plot option is selected, none of the isometric drawings will be plotted.

7.

Increment Revision Number/Do Not Increment Revision Number toggle If the Increment Revision Number option is selected, the system will update the drawing revision block when an isometric is successfully generated. If the Do Not Increment Revision Number option is selected, the system will not update the revision block. You will encounter problems later when attempting to delete a drawing if a revision history does not exist for a drawing. Refer to Delete Drawing, page 5 - 46 for more information about deleting drawings. When the batch job is run, the system will use the inputs for By, Chk, Date and Descr to update the revision block for the drawing in the Project Control Database.

8.

By, Chk, Date, Descr To increment drawing revision numbers, key in information to these fields to specify the revision block data.


The data will be written back to the Project Control Database only if the isometric is successfully extracted. If you leave the Date field blank, the current date will be used. The Date field allows you to specify an issue date for the isometric that is different from the current date. If, for example, you are extracting a number of drawings over a period of a few days for issue on a given date, you should key in that issue date to this field. Rather than key in Chk initials at extraction time, you might want to update the Project Control Database with Chk and Aprv initials after the drawing has been plotted. 9.

Search Criteria: The following are search criteria that can be used separately or together to locate a drawing or group of drawings within an iso area. All defined search criteria must be met before a drawing can be included in an isometric extraction.

Type Select the Type field gadget and select the appropriate isometric drawing type. Using this option will help limit the number of drawings displayed. Iso Area Key in the name of the iso area that you want to extract lines from.

— OR —

a.


5 - 94

b.


Select the appropriate iso area and the accept button. The system returns to the Create Batch Job Input form with the selected area in the Iso Area field. To restrict the list further, you must supply additional criteria such as batch reference numbers and drawing numbers.

Batch Reference Key in the batch reference number of the lines you want to extract. To use batch reference numbers as criteria, specify them in individual drawing records when adding drawing records to the Project Control Database. Model Status Code Key in the status code if you want to restrict a list to all lines of a given status. Drawing Number Low / Drawing Number High Drawing Number High and Drawing Number Low define, by drawing number, the range of lines to extract. Key in a drawing number in each field to identify the lines to extract.

— OR —


a.

Activate a cursor in the Drawing Number Low field by placing a data point.

b.

Select the Drawing List button. The system activates the List Drawings form.

c.

Select the drawing that will represent the low drawing number and select the accept button. The system returns to the Create Batch Job Input form with the selected drawing displayed in the Drawing Number Low field.

d. 10.

Repeat the above steps for the Drawing Number High field.

Do Not Use Model Revised Date / Use Model Revised Date toggle Select the Use Model Revise Date option to specify that only lines whose Model Revised date is greater than the last drawing revision date can be included in the list of lines to extract.

11.

Once all of the necessary search criteria has been set, select the accept button to begin processing. If enabled, the system displays the Write to Batch Input File Cancel/Accept form.

5 - 96

12.


Select the Accept button to begin posting the list to the batch input file. The Write to Batch Input File Cancel/Accept form is an added feature to help prevent new users from writing an unnecessary number of lines to the batch input file. To prevent the form from being displayed, add the following environment variable: In the pds.cmd file, $ENV{’NO_CONFIRM_WRITE_BJ’} = ’anything’;

13.

Select By Line ID The Select by Line ID button can be used instead of the various search criteria to select lines for the batch input file. It allows you to select individual lines for extraction as opposed to defining different search criteria to select a specific group of lines. a.

Select the Select By Line ID button. The system displays the List Iso Areas form.

Select an iso area and the accept button. The system displays a second Create Batch Job Input form which lists all lines contained within the selected iso area.


b.

Select the lines to be included in the batch file. — OR — Select the Type field gadget and select the appropriate isometric drawing type. Using this option will help limit the number of drawings displayed for selection. — OR — Select the Select All button to include all of the listed files in the batch file. — OR — Select the Iso Area List button to select a different iso area from the List Iso Areas form. Use the Reset Selection button at any time to cancel all previous line selections.

c.

Select the accept button once all of the appropriate lines have been selected. The system activates the third Create Batch Job Input form. The By, Chk, Date and Description fields will be initialized with the input values that were entered in step 8.

5 - 98

d.


If necessary, select the By, Chk, Date, and Description fields on the form and key in the appropriate information for each line. If any of the previously mentioned fields are revised, each line is posted to the batch input file with separate option lines. If the fields are not revised, all of the selected lines will be posted to the batch input file under the same option lines.

e.

Select the accept button The system posts the list to the batch input file.

14.

Iso Type This field is for review purposes only. It displays the type of drawings that are listed.

15.

Iso Area List This button displays the List Iso Areas form. When an Iso Area is selected from the form and accepted, the system returns to the Create Batch Job Input form with the iso area in the Iso Area field.

16.

Drawing List This button displays the List Iso Areas form. Once an area(s) is selected and accepted, the systems displays the List Drawings form. Select the cancel button to dismiss the form and return to the Create Batch Job Input form.


17.

Schedule Batch Job This button displays the Schedule Batch Job form. Refer to the next section, Schedule Batch Job, for more information.

5 - 100


5.3.11 Schedule Batch Job __________________________________________________________________________________________________________________________________________________ The Schedule Batch Job command allows you to schedule a batch job for isometric extraction. 1.

Select the Schedule Batch Job button from the Batch Environment form. The system activates the Schedule Batch Job form.

2.

Batch Input File Key in the name of the batch input file that was previously created using the Create Batch Job Input command from the Batch Environment form. Blank fields in the file specification will be defaulted according to the current default directory. If the file name does not exist, an error message will be displayed at the bottom of the form. If the file name is valid, the remaining fields in the form will be given default values with the exception of the Run Time fields.


3.

System Log File Key in the name of a log file. This field allows you to create a log of the command execution as the job processes in batch. This log is useful when you are having difficulties getting the batch software to operate. It contains a log of all error messages issued by the various software modules used to create an isometric. The System log file (.job file) is different from the batch log file (.log file) created by the batch procedure. The system log file is named using the batch input file name together with a file extension of .job. The batch log file contains an entry for each attempted run together with an error code and/or message when the run fails. All .job and .log files are written to the same directory as the batch job input file. If this is not the case, have your system administrator check the hosts.nqs file to verify write permissions. If the batch job input file name remains the same, the .log file will maintain a cumulative history of each successive run.

4.

Job Name Key in a batch job name. This is the name for the batch run which will show up in the batch queue when you key in the qstat PDisocreate command. The default job name is the batch input file name.

5.

Process Queue Select one of the queues from the pull down list. The selected batch queue will extract the lines as defined in the batch input file. The queues displayed in the Process Queue field are chosen first from the queues defined in the PDiso_batch portion of the queue_descript file (located in the project directory). If no queues are defined in the queue_descript file, the system generates a Process Queue list from locally defined queues. Valid queue names include: PDiso_batch, PDiso_bat_1, PDiso_bat_*.

6.

Mail Notify Key in the email path of the machine that will be sent a mail message when the batch iso processing completes. A default for this field is provided by your system manager when the iso extraction product is installed on your system. The mail message contains the identification of the batch job input file, the Project Control Database name, a brief error message, and an error code. The error code is explained in more detail in Appendix A.

7.

Plot Queue Select one of the queues from the pull down list. This field is only displayed if the file defined in the Batch Job Input File field was created with the Submit for Plotting toggle turned on. Refer to Create Batch Job Input, page 5 - 89 for more information on defining batch job input files.

5 - 102


The queues displayed in the Plot Queue field are chosen first from the queues defined in the PDiso_plot portion of the queue_descript file (located in the project directory). If no queues are defined in the queue_descript file, the system generates a Plot Queue list from locally defined queues. If locally defined queues are used, only the pipe queues that are defined will be displayed in the Plot Queue pull down list. To display local device queues, create a pipe queue that points to the device queue. Valid queue names include: PDiso_plot, PDiso_plot_1, PDiso_plt_*. 8.

Plot Copies Keyin the number of copies to be plotted for each extracted line.

9.

Do Not Generate PDME Data / Generate PDME Data When set to Generate PDME Data, ISOGEN creates a .pdm file in the iso output directory. The resulting .pdm file is used when exporting data to PDME (Plant Data Maintenance Environment). Refer to the Export to PDME command in the PDS Project Administrator document for information. When using this option, Intergraph options 4 (ISOGEN component vs sheet number file) and 20 (Intergraph MTO Neutral File) must be set to 1 (active).

10.

Do Not Extract Existing Sheets / Re-Extract Existing Sheets When set to Do Not Extract Existing Sheets, ISOGEN extracts the line and determines the amount of information that will be placed on each sheet and splits them accordingly. When set to Re-Extract Existing Sheets, ISOGEN extracts the line normally. However, unlike the previous toggle setting, the system honors the previous extraction’s pagination. Refer to Repeatability, page 15 - 1 for additional information. This toggle should be set to Do Not Extract Existing Sheets if extensive changes are being made to a pipeline. If extensive revisions are made to a line and the previous pagination is honored, the result may be a sheet that contains too much information to decipher.

11.

Do Not Save Sheet Extraction Data / Save Sheet Extraction Data When the toggle is set to Save Sheet Extraction Data, the system generates and stores repeating data in the project and design databases. Repeating data includes such information as: traversal startpoint (saved to the project database) and the extracted item’s iso sheet number (saved to the design database). Refer to Repeatability, page 15 - 1 for additional information. This toggle should be set to Do Not Save Sheet Extraction Data until the design is stable and your isometrics are ready to be issued for the first time.


12.

Verify On / Verify Off toggle Select the Verify On option to turn on batch job verification. Select the Verify Off option to turn off batch job verification. When verification is on, a log of all system commands executed by the batch extraction procedure is saved in the iso output directory. Do not enable verification when large numbers of iso’s are being created since the resulting log files will use a large amount of disk space.

13.

Debug On / Debug Off toggle Select the Debug On option to enable the debugging logic in the batch job. Select the Debug Off option to disable the debugging logic in the batch job. The debugging logic causes the values of several batch procedure variables to be displayed in the system log file. This option is useful for tracking down problems or submitting problems to Intergraph.

14.

Submit Batch Immediately/Delay Batch Submit Time toggle Select the Submit Batch Immediately option to run the job immediately. Select the Delay Batch Submit Time to specify a run time for the job. Define the run time by keying in the day of the week (Mon, Tue, etc.), the time and then select AM or PM.

15.

After all fields contain the appropriate information, select the accept button. As described earlier, a batch job log file (containing an entry for each attempted extraction) is created and updated as the batch job executes. Examine this log after the job finishes to see that all drawings were successfully completed. When drawings fail, consult Appendix A for a more detailed explanation of the error code and message found in the log file. Also, check the .err files produced by the ISOGEN interface to make sure that the drawings do not contain errors. The batch shell marks each entry in the batch job input file as it is processed. Therefore, the batch procedure can be stopped and then restarted at any later time without causing drawings that have already completed to be rerun. If the system goes down and the job is not restarted automatically, it can be restarted using the Schedule Batch Job command. Drawings that have already been created will not be re-executed.

5 - 104


5.3.12 Reports __________________________________________________________________________________________________________________________________________________ The Reports command allows you to define the report type and to choose whether or not an area or drawing will be included in the report. Before reports can be printed, a pipe queue named PDprint must exist. For information on creating pipe queues for PDS, refer to the section Printer/Plotter Setup in the PD Project Administrator (PD_Project) Reference Guide. 1.

Select the Reports button from the Batch Environment form. The system displays the Batch Data Reports form.

2.

Key in the report filename in the Output File field. If the system default variable, ISOREPORT, is exported in the control.sh file, the system will default to that value. For example: ISOREPORT=node:/usr/directory.

3.

Choose a report type.


Area Summary creates an area summary report which shows all of the data associated with one or more piping areas. This report lists information such as: Equipment Areas Continuation Areas The Current Default Set User Data Default (Options) Summary creates an options summary report which shows all default sets. This report lists information such as: ISOGEN Project Options Information on Each Default Set (such as the seed file, plot file, the default output path and border file defined for each default set) Drawing Summary creates a drawing summary report which shows selected data about each drawing that you are reporting. This reports lists information such as: Drawing Number Revision Number Most Recent Revision Date Drawing Number Number of Sheets Most Recent MTO Date Drawing Revision History creates a revision history report which shows the revision dates for each revision of the drawings being reported. This report lists information such as: Line Number Type of Isometric Drawing Number

5 - 106


List of Drawing Revision Dates (up to the last five) Search Criteria: The following are search criteria that can be used separately or together to locate a drawing or group of drawings within an iso area. All defined search criteria must be met before a drawing can be included in the report list. If no search criteria is defined, the system generates reports on the entire project control database. Iso Area Key in the name of the iso area that you want to extract lines from.

— OR —

a.


b.

Select the appropriate iso area and the accept button. The system returns to the Batch Data Reports form with the selected area in the Iso Area field. If you want to restrict the list further, you must supply additional criteria such as batch reference numbers and drawing numbers.


Type Select the Type field gadget and select the appropriate isometric drawing type. Using this option will help limit the number of drawings displayed. Batch Reference Key in the batch reference number of the lines you want to extract.

— OR —

Select the List Drawing button for a list of batch reference numbers. To use batch reference numbers as criteria, specify them in individual drawing records when adding drawing records to the Project Control Database. Model Status Code Key in the status code if you want to restrict a list to all lines of a given status. Drawing Number Low / Drawing Number High Drawing Number High and Drawing Number Low define, by drawing number, the range of lines to extract. Key in a drawing number in each field to identify the lines to extract.

— OR —

a.

Activate a cursor in the Drawing Number Low field by placing a data point.

b.

Select the Drawing List button. The system activates the List Drawings form.

5 - 108

c.


Select the drawing that will represent the low drawing number and select the accept button. The system returns to the Batch Data Report form with the selected drawing displayed in the Drawing Number Low field.

d. 4.

Repeat the above steps for the Drawing Number High field.

Model Revised Date toggle field Select the Use Model Revise Date option to specify that only lines whose Model Revised date is greater than the last drawing revision date can be included in the list of lines to extract.

5.

Select one of three print options. Print/Delete Print/Save Save If the Print/Delete or Print/Save option is selected, the system displays a scroll field that lists available printing queues.


Select a print queue. If there is no queue connected to the client workstation, the system defaults to the Save option. 6.

Select the accept button. The system initiates report generation.

5 - 110


Interpreting the HITS Report 6 - 1

6. Interpreting the HITS Report

__________________________________________________________________________________________________________________________________________________

The HITS report is a diagnostic tool generated by the Intergraph interface to ISOGEN. You can use this report to analyze the data collected from the 3-D piping model when a problem extracting an isometric occurs. This report can help you determine whether or not the problem exists in your model, in the ISOGEN interface or in ISOGEN itself. The HITS report filename is formed from the output isometric design filename. Isometric design filename is concatenated with the file extension .h. For example, if the isometric design filename is OWS1101.ISO then the HITS report filename will be OWS1101.h. The report is created in the default directory at the time the iso is created. One of the options in the ISOGEN interface defaults file allows you to generate a HITS report only and not an intermediate data file (IDF). You may not always want to generate an IDF with a HITS report. The run time to generate both an IDF and a HITS report is significantly longer than the run time to generate a HITS report only.

6-2


6.1 Example HITS Report __________________________________________________________________________________________________________________________________________________ The following section discusses an example of a HITS report. The HITS report is composed of 5 basic sections. Refer to the following figure for an illustration of each of the five sections. The example HITS report in this section was generated using the following line.

Sheet One of Two


Sheet Two of Two Date: 30-MAR-1994 02:03:53 Project Database: pd_stdeng_o43 Model Files: skiso3 skiso1 38eqp01 40eqp01

Raw design file data ——————– Name

Occ

COMP

16

cp # 0

1369.58

X

421.10

Y

13.46

Z

Node Direct Section 0

0

0

Flags 3

Topo 0

Seq Branch Sg_occ 0

0

9

1

COMP

16

1

1369.58

420.95

13.46

0

0

0

3

0

0

0

9

2

COMP

16

2

1369.58

421.24

13.46

0

0

0

3

0

0

0

9

3

COMP

14

0

1363.08

422.45

15.18

0

0

0

3

0

0

0

5

4

COMP

14

1

1363.08

422.45

14.42

0

0

0

3

0

0

0

5

5

COMP

14

2

1363.08

422.45

15.94

0

0

0

3

0

0

0

8

6

COMP

14

3

1362.40

422.45

15.18

0

0

0

3

0

0

0

7

7

COMP

27

0

1362.35

422.45

15.18

0

0

0

3

0

0

0

7

8

COMP

27

1

1362.40

422.45

15.18

0

0

0

3

0

0

0

7

9

COMP

29

0

1369.58

422.45

18.46

0

0

0

3

0

0

0

16

10

COMP

29

1

1370.05

422.45

18.46

0

0

0

3

0

0

0

16

11

COMP

29

2

1369.11

422.45

18.46

0

0

0

3

0

0

0

17

12

COMP

29

3

1369.58

422.45

17.99

0

0

0

3

0

0

0

14

13

COMP

32

0

1373.58

422.45

18.46

0

0

0

3

0

0

0

16

14

COMP

32

1

1373.58

423.20

18.46

0

0

0

3

0

0

0

16

15

COMP

32

2

1372.83

422.45

18.46

0

0

0

3

0

0

0

16

16

COMP

33

0

1373.58

429.80

18.46

0

0

0

3

0

0

0

16

17

COMP

33

1

1372.83

429.80

18.46

0

0

0

3

0

0

0

16

18

COMP

33

2

1373.58

429.05

18.46

0

0

0

3

0

0

0

16

19

COMP

34

0

1364.58

429.80

18.46

0

0

0

3

0

0

0

16

20

COMP

34

1

1364.58

429.80

19.21

0

0

0

3

0

0

0

16

21

COMP

34

2

1365.33

429.80

18.46

0

0

0

3

0

0

0

16

22

COMP

35

0

1364.58

429.80

19.35

0

0

0

3

0

0

0

16

23

COMP

35

1

1364.58

429.80

19.51

0

0

0

3

0

0

0

16

24

COMP

35

2

1364.58

429.80

19.21

0

0

0

3

0

0

0

16

25

PIPE

5

1

1370.05

422.45

18.46

0

0

0

5

0

0

0

16

26

6-4


PIPE

5

2

1372.83

422.45

18.46

0

0

0

5

0

0

0

16

27

PIPE

6

1

1373.58

423.20

18.46

0

0

0

5

0

0

0

16

28

PIPE

6

2

1373.58

429.05

18.46

0

0

0

5

0

0

0

16

29

PIPE

7

1

1372.83

429.80

18.46

0

0

0

5

0

0

0

16

30

PIPE

7

2

1365.33

429.80

18.46

0

0

0

5

0

0

0

16

31

COMP

30

0

1363.08

422.45

18.46

0

0

0

3

0

0

0

8

32

COMP

30

1

1363.08

422.45

17.71

0

0

0

3

0

0

0

8

33

COMP

30

2

1363.83

422.45

18.46

0

0

0

3

0

0

0

17

34

PIPE

3

1

1369.11

422.45

18.46

0

0

0

5

0

0

0

17

35

PIPE

3

2

1363.83

422.45

18.46

0

0

0

5

0

0

0

17

36

COMP

17

0

1369.58

421.47

13.41

0

0

0

3

0

0

0

11

37

COMP

17

1

1369.58

421.70

13.37

0

0

0

3

0

0

0

11

38

COMP

17

2

1369.58

421.24

13.46

0

0

0

3

0

0

0

10

39

COMP

17

3T

1369.58

421.47

13.18

0

0

0

3

0

0

0

12

40

COMP

6

0

1363.08

421.10

13.46

0

0

0

3

0

0

0

3

41

COMP

6

1

1363.08

420.95

13.46

0

0

0

3

0

0

0

3

42

COMP

6

2

1363.08

421.24

13.46

0

0

0

3

0

0

0

3

43

COMP

15

0

1363.08

422.45

16.38

0

0

0

3

0

0

0

8

44

COMP

15

1

1363.08

422.45

15.94

0

0

0

3

0

0

0

8

45

COMP

15

2

1363.08

422.45

16.82

0

0

0

3

0

0

0

8

46

COMP

31

0

1363.08

422.45

16.97

0

0

0

3

0

0

0

8

47

COMP

31

1

1363.08

422.45

16.82

0

0

0

3

0

0

0

8

48

COMP

31

2

1363.08

422.45

17.12

0

0

0

3

0

0

0

8

49

PIPE

4

1

1363.08

422.45

17.71

0

0

0

5

0

0

0

8

50

PIPE

4

2

1363.08

422.45

17.12

0

0

0

5

0

0

0

8

51

COMP

7

0

1363.08

421.47

13.41

0

0

0

3

0

0

0

5

52

COMP

7

1

1363.08

421.70

13.37

0

0

0

3

0

0

0

5

53

COMP

7

2

1363.08

421.24

13.46

0

0

0

3

0

0

0

4

54

COMP

7

3T

1363.08

421.47

13.18

0

0

0

3

0

0

0

6

55

COMP

8

0

1363.08

421.47

13.06

0

0

0

3

0

0

0

6

56

COMP

8

1

1363.08

421.47

13.18

0

0

0

3

0

0

0

6

57

COMP

8

2

1363.08

421.47

12.93

0

0

0

3

0

0

0

6

58

COMP

9

0

1363.08

421.47

12.82

0

0

0

3

0

0

0

6

59

COMP

9

1

1363.08

421.47

12.93

0

0

0

3

0

0

0

6

60

COMP

9

2

1363.08

421.47

12.71

0

0

0

3

0

0

0

6

61

COMP

10

0

1363.08

421.47

12.58

0

0

0

3

0

0

0

6

62

COMP

10

1

1363.08

421.47

12.71

0

0

0

3

0

0

0

6

63

COMP

10

2

1363.08

421.47

12.46

0

0

0

3

0

0

0

6

64

COMP

11

0

1363.08

421.47

12.43

0

0

0

3

0

0

0

6

65

COMP

11

1

1363.08

421.47

12.46

0

0

0

3

0

0

0

6

66

COMP

26

0

1364.58

429.80

19.54

0

0

0

3

0

0

0

15

67

COMP

26

1

1364.58

429.80

19.58

0

0

0

3

0

0

0

15

68

COMP

26

2

1364.58

429.80

19.51

0

0

0

3

0

0

0

15

69

COMP

22

0

1369.58

422.45

13.37

0

0

0

3

0

0

0

11

70

COMP

22

1

1369.58

421.70

13.37

0

0

0

3

0

0

0

11

71

COMP

22

2

1369.58

422.45

14.12

0

0

0

3

0

0

0

11

72

COMP

23

0

1369.58

422.45

14.27

0

0

0

3

0

0

0

11

73

COMP

23

1

1369.58

422.45

14.42

0

0

0

3

0

0

0

11

74

COMP

23

2

1369.58

422.45

14.12

0

0

0

3

0

0

0

11

75

COMP

24

0

1369.58

422.45

15.18

0

0

0

3

0

0

0

11

76

COMP

24

1

1369.58

422.45

14.42

0

0

0

3

0

0

0

11

77

COMP

24

2

1369.58

422.45

15.94

0

0

0

3

0

0

0

14

78

COMP

24

3

1368.90

422.45

15.18

0

0

0

3

0

0

0

13

79

SUPP

4

1

1369.58

422.45

13.37

0

0

0

8

0

0

0

11

80

SUPP

4

2

1369.58

422.45

12.30

0

0

0

8

0

0

0

11

81

COMP

12

0

1363.08

422.45

13.37

0

0

0

3

0

0

0

5

82

COMP

12

1

1363.08

421.70

13.37

0

0

0

3

0

0

0

5

83

COMP

12

2

1363.08

422.45

14.12

0

0

0

3

0

0

0

5

84

COMP

13

0

1363.08

422.45

14.27

0

0

0

3

0

0

0

5

85

COMP

13

1

1363.08

422.45

14.42

0

0

0

3

0

0

0

5

86

COMP

13

2

1363.08

422.45

14.12

0

0

0

3

0

0

0

5

87

SUPP

3

1

1363.08

422.45

13.37

0

0

0

8

0

0

0

5

88

SUPP

3

2

1363.08

422.45

12.30

0

0

0

8

0

0

0

5

89

COMP

25

0

1369.58

422.45

16.38

0

0

0

3

0

0

0

14

90

COMP

25

1

1369.58

422.45

15.94

0

0

0

3

0

0

0

14

91


COMP

25

2

1369.58

422.45

16.82

0

0

0

3

0

0

0

14

92

COMP

305

0

1369.58

422.45

16.97

0

0

0

3

0

0

0

14

93

COMP

305

1

1369.58

422.45

16.82

0

0

0

3

0

0

0

14

94

COMP

305

2

1369.58

422.45

17.12

0

0

0

3

0

0

0

14

95

PIPE

103

1

1369.58

422.45

17.12

0

0

0

5

0

0

0

14

96

PIPE

103

2

1369.58

422.45

17.99

0

0

0

5

0

0

0

14

97

COMP

18

0

1369.58

421.47

13.06

0

0

0

3

0

0

0

12

98

COMP

18

1

1369.58

421.47

13.18

0

0

0

3

0

0

0

12

99

COMP

18

2

1369.58

421.47

12.93

0

0

0

3

0

0

0

12

100

COMP

19

0

1369.58

421.47

12.82

0

0

0

3

0

0

0

12

101

COMP

19

1

1369.58

421.47

12.93

0

0

0

3

0

0

0

12

102

COMP

19

2

1369.58

421.47

12.71

0

0

0

3

0

0

0

12

103

COMP

20

0

1369.58

421.47

12.58

0

0

0

3

0

0

0

12

104

COMP

20

1

1369.58

421.47

12.71

0

0

0

3

0

0

0

12

105

COMP

20

2

1369.58

421.47

12.46

0

0

0

3

0

0

0

12

106

COMP

21

0

1369.58

421.47

12.43

0

0

0

3

0

0

0

12

107

COMP

21

1

1369.58

421.47

12.46

0

0

0

3

0

0

0

12

108

COMP

28

0

1368.85

422.45

15.18

0

0

0

3

0

0

0

13

109

COMP

28

1

1368.90

422.45

15.18

0

0

0

3

0

0

0

13

110

Design file data sorted by coordinate ————————————Name

Occ

COMP

27

0

1362.35

422.45

15.18

-2

3

0

3

0

0

0

7

1

COMP

27

1

1362.40

422.45

15.18

1

3

0

3

0

0

0

7

2

COMP

14

3

1362.40

422.45

15.18

1

3

0

3

0

0

0

7

3

1

1

1363.08

420.70

13.46

-1

11

0

22

0

0

0

3

4

NOZ

cp #

X

Y

Z

Node Direct Section

Flags

Topo

Seq Branch Sg_occ

NOZ

1

2

1363.08

420.95

13.46

40

11

0

22

0

0

0

3

5

COMP

6

1

1363.08

420.95

13.46

40

11

0

3

0

0

0

3

6

COMP

6

0

1363.08

421.10

13.46

0

11

0

3

0

0

0

3

7

COMP

6

2

1363.08

421.24

13.46

2

11

0

3

0

0

0

3

8

COMP

7

2

1363.08

421.24

13.46

2

12

0

3

0

0

0

4

9

COMP

11

0

1363.08

421.47

12.43

-2

13

0

3

0

0

0

6

10

COMP

11

1

1363.08

421.47

12.46

3

13

0

3

0

0

0

6

11

COMP

10

2

1363.08

421.47

12.46

3

13

0

3

0

0

0

6

12

COMP

10

0

1363.08

421.47

12.58

0

13

0

3

0

0

0

6

13

COMP

9

2

1363.08

421.47

12.71

4

13

0

3

0

0

0

6

14

COMP

10

1

1363.08

421.47

12.71

4

13

0

3

0

0

0

6

15

COMP

9

0

1363.08

421.47

12.82

0

13

0

3

0

0

0

6

16

COMP

9

1

1363.08

421.47

12.93

5

13

0

3

0

0

0

6

17

COMP

8

2

1363.08

421.47

12.93

5

13

0

3

0

0

0

6

18

COMP

8

0

1363.08

421.47

13.06

0

13

0

3

0

0

0

6

19

COMP

7

3T

1363.08

421.47

13.18

6

13

0

3

0

0

0

6

20

COMP

8

1

1363.08

421.47

13.18

6

13

0

3

0

0

0

6

21

COMP

7

0

1363.08

421.47

13.41

0

13

0

3

0

0

0

5

22

COMP

12

1

1363.08

421.70

13.37

7

15

0

3

0

0

0

5

23

COMP

7

1

1363.08

421.70

13.37

7

12

0

3

0

0

0

5

24

SUPP

3

2

1363.08

422.45

12.30

-3

2

0

8

0

0

0

5

25

COMP

12

0

1363.08

422.45

13.37

0

15

0

3

0

0

0

5

26

SUPP

3

1

1363.08

422.45

13.37

0

2

0

8

0

0

0

5

27

COMP

13

2

1363.08

422.45

14.12

9

2

0

3

0

0

0

5

28

COMP

12

2

1363.08

422.45

14.12

9

2

0

3

0

0

0

5

29

COMP

13

0

1363.08

422.45

14.27

0

2

0

3

0

0

0

5

30

COMP

13

1

1363.08

422.45

14.42

10

2

0

3

0

0

0

5

31

COMP

14

1

1363.08

422.45

14.42

10

2

0

3

0

0

0

5

32

COMP

14

0

1363.08

422.45

15.18

0

3

0

3

0

0

0

5

33

COMP

15

1

1363.08

422.45

15.94

11

2

0

3

0

0

0

8

34

COMP

14

2

1363.08

422.45

15.94

11

2

0

3

0

0

0

8

35

COMP

15

0

1363.08

422.45

16.38

0

2

0

3

0

0

0

8

36

COMP

31

1

1363.08

422.45

16.82

12

2

0

3

0

0

0

8

37

COMP

15

2

1363.08

422.45

16.82

12

2

0

3

0

0

0

8

38

COMP

31

0

1363.08

422.45

16.97

0

2

0

3

0

0

0

8

39

COMP

31

2

1363.08

422.45

17.12

13

2

0

3

0

0

0

8

40

PIPE

4

2

1363.08

422.45

17.12

13

2

0

5

0

0

0

8

41

COMP

30

1

1363.08

422.45

17.71

14

2

0

3

0

0

0

8

42

6-6


PIPE

4

1

1363.08

422.45

17.71

14

2

0

5

0

0

0

8

COMP

30

0

1363.08

422.45

18.46

0

4

0

3

0

0

0

8

43 44

PIPE

3

2

1363.83

422.45

18.46

15

4

0

5

0

0

0

17

45

COMP

30

2

1363.83

422.45

18.46

15

4

0

3

0

0

0

17

46

COMP

34

0

1364.58

429.80

18.46

0

8

0

3

0

0

0

16

47

COMP

35

2

1364.58

429.80

19.21

16

8

0

3

0

0

0

16

48

COMP

34

1

1364.58

429.80

19.21

16

8

0

3

0

0

0

16

49

COMP

35

0

1364.58

429.80

19.35

0

8

0

3

0

0

0

16

50

COMP

35

1

1364.58

429.80

19.51

17

8

0

3

0

0

0

16

51

COMP

26

2

1364.58

429.80

19.51

17

8

0

3

0

0

0

15

52

COMP

26

0

1364.58

429.80

19.54

0

8

0

3

0

0

0

15

53

COMP

26

1

1364.58

429.80

19.58

41

8

0

3

0

0

0

15

54

NOZ

7

2

1364.58

429.80

19.58

41

8

0

22

0

0

0

15

55

NOZ

7

1

1364.58

429.80

20.58

-1

8

0

22

0

0

0

15

56

COMP

34

2

1365.33

429.80

18.46

18

7

0

3

0

0

0

16

57

PIPE

7

2

1365.33

429.80

18.46

18

7

0

5

0

0

0

16

58

COMP

28

0

1368.85

422.45

15.18

-2

3

0

3

0

0

0

13

59

COMP

24

3

1368.90

422.45

15.18

19

3

0

3

0

0

0

13

60

COMP

28

1

1368.90

422.45

15.18

19

3

0

3

0

0

0

13

61

PIPE

3

1

1369.11

422.45

18.46

20

4

0

5

0

0

0

17

62

COMP

29

2

1369.11

422.45

18.46

20

4

0

3

0

0

0

17

63

NOZ

3

1

1369.58

420.70

13.46

-1

1

0

22

0

0

0

9

64

NOZ

3

2

1369.58

420.95

13.46

39

1

0

22

0

0

0

9

65

COMP

16

1

1369.58

420.95

13.46

39

1

0

3

0

0

0

9

66

COMP

16

0

1369.58

421.10

13.46

0

1

0

3

0

0

0

9

67

COMP

16

2

1369.58

421.24

13.46

21

1

0

3

0

0

0

9

68

COMP

17

2

1369.58

421.24

13.46

21

9

0

3

0

0

0

10

69

COMP

21

0

1369.58

421.47

12.43

-2

10

0

3

0

0

0

12

70

COMP

21

1

1369.58

421.47

12.46

22

10

0

3

0

0

0

12

71

COMP

20

2

1369.58

421.47

12.46

22

10

0

3

0

0

0

12

72

COMP

20

0

1369.58

421.47

12.58

0

10

0

3

0

0

0

12

73

COMP

20

1

1369.58

421.47

12.71

23

10

0

3

0

0

0

12

74

COMP

19

2

1369.58

421.47

12.71

23

10

0

3

0

0

0

12

75

COMP

19

0

1369.58

421.47

12.82

0

10

0

3

0

0

0

12

76

COMP

18

2

1369.58

421.47

12.93

24

10

0

3

0

0

0

12

77

COMP

19

1

1369.58

421.47

12.93

24

10

0

3

0

0

0

12

78

COMP

18

0

1369.58

421.47

13.06

0

10

0

3

0

0

0

12

79

COMP

17

3T

1369.58

421.47

13.18

25

10

0

3

0

0

0

12

80

COMP

18

1

1369.58

421.47

13.18

25

10

0

3

0

0

0

12

81

COMP

17

0

1369.58

421.47

13.41

0

10

0

3

0

0

0

11

82

COMP

22

1

1369.58

421.70

13.37

26

14

0

3

0

0

0

11

83

COMP

17

1

1369.58

421.70

13.37

26

9

0

3

0

0

0

11

84

SUPP

4

2

1369.58

422.45

12.30

-3

5

0

8

0

0

0

11

85

COMP

22

0

1369.58

422.45

13.37

0

14

0

3

0

0

0

11

86

SUPP

4

1

1369.58

422.45

13.37

0

5

0

8

0

0

0

11

87

COMP

22

2

1369.58

422.45

14.12

28

5

0

3

0

0

0

11

88

COMP

23

2

1369.58

422.45

14.12

28

5

0

3

0

0

0

11

89

COMP

23

0

1369.58

422.45

14.27

0

5

0

3

0

0

0

11

90

COMP

23

1

1369.58

422.45

14.42

29

5

0

3

0

0

0

11

91

COMP

24

1

1369.58

422.45

14.42

29

5

0

3

0

0

0

11

92

COMP

24

0

1369.58

422.45

15.18

0

5

0

3

0

0

0

11

93

COMP

24

2

1369.58

422.45

15.94

30

5

0

3

0

0

0

14

94

COMP

25

1

1369.58

422.45

15.94

30

5

0

3

0

0

0

14

95

COMP

25

0

1369.58

422.45

16.38

0

5

0

3

0

0

0

14

96

COMP

25

2

1369.58

422.45

16.82

31

5

0

3

0

0

0

14

97

COMP

305

1

1369.58

422.45

16.82

31

5

0

3

0

0

0

14

98

COMP

305

0

1369.58

422.45

16.97

0

5

0

3

0

0

0

14

99

PIPE

103

1

1369.58

422.45

17.12

32

5

0

5

0

0

0

14

100

COMP

305

2

1369.58

422.45

17.12

32

5

0

3

0

0

0

14

101

PIPE

103

2

1369.58

422.45

17.99

33

5

0

5

0

0

0

14

102

COMP

29

3

1369.58

422.45

17.99

33

5

0

3

0

0

0

14

103

COMP

29

0

1369.58

422.45

18.46

0

5

0

3

0

0

0

16

104

COMP

29

1

1370.05

422.45

18.46

34

4

0

3

0

0

0

16

105

PIPE

5

1

1370.05

422.45

18.46

34

4

0

5

0

0

0

16

106

PIPE

5

2

1372.83

422.45

18.46

35

4

0

5

0

0

0

16

107


COMP

32

2

1372.83

422.45

18.46

35

4

0

3

0

0

0

16

108

PIPE

7

1

1372.83

429.80

18.46

36

7

0

5

0

0

0

16

109

COMP

33

1

1372.83

429.80

18.46

36

7

0

3

0

0

0

16

110

COMP

32

0

1373.58

422.45

18.46

0

6

0

3

0

0

0

16

111

COMP

32

1

1373.58

423.20

18.46

37

6

0

3

0

0

0

16

112

PIPE

6

1

1373.58

423.20

18.46

37

6

0

5

0

0

0

16

113

COMP

33

2

1373.58

429.05

18.46

38

6

0

3

0

0

0

16

114

PIPE

6

2

1373.58

429.05

18.46

38

6

0

5

0

0

0

16

115

COMP

33

0

1373.58

429.80

18.46

0

7

0

3

0

0

0

16

116

Tracing data ———— Occ

Cp

5 Next

Action

3

2

Name NOZ

Node 39

Ref Design 112

1

1

1

5 Next

16

1

COMP

39

2

1

1

2

5 Next

16

2

COMP

21

3

1

1

3

5 Next

17

2

COMP

21

39

1

1

4

6 Push

17

3

COMP

25

40

1

0

0

5 Next

17

1

COMP

26

38

1

1

5

5 Next

22

1

COMP

26

71

1

1

6

5 Next

22

2

COMP

28

72

1

1

7

5 Next

23

2

COMP

28

75

1

1

8

5 Next

23

1

COMP

29

74

1

1

9

5 Next

24

1

COMP

29

77

1

1

10

6 Push

24

3

COMP

19

79

1

0

0

5 Next

24

2

COMP

30

78

1

1

11

5 Next

25

1

COMP

30

91

1

1

12

5 Next

25

2

COMP

31

92

1

1

13

5 Next

305

1

COMP

31

94

1

1

14

5 Next

305

2

COMP

32

95

1

1

15

5 Next

103

1

PIPE

32

96

1

1

16

5 Next

103

2

PIPE

33

97

1

1

17

5 Next

29

3

COMP

33

13

1

1

18

6 Push

29

2

COMP

20

12

1

0

0

5 Next

29

1

COMP

34

11

1

2

1

5 Next

5

1

PIPE

34

26

1

2

2

5 Next

5

2

PIPE

35

27

1

2

3

5 Next

32

2

COMP

35

16

1

2

4

5 Next

32

1

COMP

37

15

1

2

5

5 Next

6

1

PIPE

37

28

1

2

6

5 Next

6

2

PIPE

38

29

1

2

7

5 Next

33

2

COMP

38

19

1

2

8

5 Next

33

1

COMP

36

18

1

2

9

5 Next

7

1

PIPE

36

30

1

2

10

5 Next

7

2

PIPE

18

31

1

2

11

5 Next

34

2

COMP

18

22

1

2

12

5 Next

34

1

COMP

16

21

1

2

13

5 Next

35

2

COMP

16

25

1

2

14

5 Next

35

1

COMP

17

24

1

2

15

5 Next

26

2

COMP

17

69

1

2

16

5 Next

26

1

COMP

41

68

1

2

17

5 Next

7

2

NOZ

41

116

1

2

18

5 Next

7

1

NOZ

-1

115

1

2

7 Pull

29

2

COMP

20

12

1

5 Next

29

2

COMP

20

12

1

2

-1

5 Next

3

1

PIPE

20

35

1

2

-2

5 Next

3

2

PIPE

15

36

1

2

-3

5 Next

30

2

COMP

15

34

1

2

-4

5 Next

30

1

COMP

14

33

1

2

-5

5 Next

4

1

PIPE

14

50

1

2

-6

5 Next

4

2

PIPE

13

51

1

2

-7

5 Next

31

2

COMP

13

49

1

2

-8

5 Next

31

1

COMP

12

48

1

2

-9

5 Next

15

2

COMP

12

46

1

2

-10

5 Next

15

1

COMP

11

45

1

2

-11

++++

++++

++++

—-

2

19 0

6-8


5 Next

14

2

COMP

11

6

1

6 Push

14

3

COMP

1

7

1

5 Next

14

1

COMP

10

5

5 Next

13

1

COMP

10

5 Next

13

2

COMP

9

5 Next

12

2

COMP

5 Next

12

1

5 Next

7

6 Push

2 ++++

-12

0

0

1

2

-13

86

1

2

-14

87

1

2

-15

9

84

1

2

-16

COMP

7

83

1

2

-17

1

COMP

7

53

1

2

-18

7

3

COMP

6

55

1

5 Next

7

2

COMP

2

54

5 Next

6

2

COMP

2

5 Next

6

1

COMP

40

5 Next

1

2

NOZ

5 Next

1

1

7 Pull

7

5 Next

++++

0

0

1

2

-19

43

1

2

-20

42

1

2

-21

40

114

1

2

-22

NOZ

-1

113

1

2

-23

3

COMP

6

55

1

7

3

COMP

6

55

1

3

1

5 Next

8

1

COMP

6

57

1

3

2

5 Next

8

2

COMP

5

58

1

3

3

5 Next

9

1

COMP

5

60

1

3

4

5 Next

9

2

COMP

4

61

1

3

5

5 Next

10

1

COMP

4

63

1

3

6

5 Next

10

2

COMP

3

64

1

3

7

5 Next

11

1

COMP

3

66

1

3

8

5 Next

11

0

COMP

-2

65

1

3

7 Pull

14

3

COMP

1

7

1

5 Next

14

3

COMP

1

7

1

4

1

5 Next

27

1

COMP

1

9

1

4

2

5 Next

27

0

COMP

-2

8

1

4

7 Pull

24

3

COMP

19

79

1

5 Next

24

3

COMP

19

79

1

5

1

5 Next

28

1

COMP

19

110

1

5

2

5 Next

28

0

COMP

-2

109

1

5

7 Pull

17

3

COMP

25

40

1

5 Next

17

3

COMP

25

40

1

6

1

5 Next

18

1

COMP

25

99

1

6

2

5 Next

18

2

COMP

24

100

1

6

3

5 Next

19

1

COMP

24

102

1

6

4

5 Next

19

2

COMP

23

103

1

6

5

5 Next

20

1

COMP

23

105

1

6

6

5 Next

20

2

COMP

22

106

1

6

7

5 Next

21

1

COMP

22

108

1

6

8

5 Next

21

0

COMP

-2

107

1

6

-1

39

21

26

28

29

30

31

32

33

34

35

37

38

36

18

16

17

41

20

15

14

13

12

11

10

9

7

2

40

6

5

4

3

1

19

25

24

23

22

—-

—-

—-

—-

0

0

0

9 0

0

3 0

0

3 0

9

0 # Sections: 1

Design file data sorted by topo ——————————Name

Occ

COMP

16

cp # 0

1369.58

X

421.10

Y

13.46

Z


1

0

Flags 3

Topo 0

Seq Branch Sg_occ 0

0

9

1

COMP

9

0

1363.08

421.47

12.82

0

13

0

3

0

0

0

6

2

COMP

30

0

1363.08

422.45

18.46

0

4

0

3

0

0

0

8

3

COMP

14

0

1363.08

422.45

15.18

0

3

0

3

0

0

0

5

4

COMP

10

0

1363.08

421.47

12.58

0

13

0

3

0

0

0

6

5

COMP

305

0

1369.58

422.45

16.97

0

5

0

3

0

0

0

14

6

COMP

32

0

1373.58

422.45

18.46

0

6

0

3

0

0

0

16

7

COMP

17

0

1369.58

421.47

13.41

0

10

0

3

0

0

0

11

8

COMP

26

0

1364.58

429.80

19.54

0

8

0

3

0

0

0

15

9

COMP

29

0

1369.58

422.45

18.46

0

5

0

3

0

0

0

16

10

COMP

18

0

1369.58

421.47

13.06

0

10

0

3

0

0

0

12

11

COMP

22

0

1369.58

422.45

13.37

0

14

0

3

0

0

0

11

12

COMP

13

0

1363.08

422.45

14.27

0

2

0

3

0

0

0

5

13


COMP

8

0

1363.08

421.47

13.06

0

13

0

3

0

0

0

6

14

COMP

23

0

1369.58

422.45

14.27

0

5

0

3

0

0

0

11

15

COMP

15

0

1363.08

422.45

16.38

0

2

0

3

0

0

0

8

16

COMP

33

0

1373.58

429.80

18.46

0

7

0

3

0

0

0

16

17

COMP

24

0

1369.58

422.45

15.18

0

5

0

3

0

0

0

11

18

COMP

31

0

1363.08

422.45

16.97

0

2

0

3

0

0

0

8

19

COMP

34

0

1364.58

429.80

18.46

0

8

0

3

0

0

0

16

20

COMP

12

0

1363.08

422.45

13.37

0

15

0

3

0

0

0

5

21

COMP

19

0

1369.58

421.47

12.82

0

10

0

3

0

0

0

12

22

COMP

35

0

1364.58

429.80

19.35

0

8

0

3

0

0

0

16

23

COMP

6

0

1363.08

421.10

13.46

0

11

0

3

0

0

0

3

24

COMP

25

0

1369.58

422.45

16.38

0

5

0

3

0

0

0

14

25

COMP

20

0

1369.58

421.47

12.58

0

10

0

3

0

0

0

12

26

COMP

7

0

1363.08

421.47

13.41

0

13

0

3

0

0

0

5

27

SUPP

4

1

1369.58

422.45

13.37

0

5

0

8

0

0

0

11

28

SUPP

3

1

1363.08

422.45

13.37

0

2

0

8

0

0

0

5

29

SUPP

3

2

1363.08

422.45

12.30

-3

2

0

8

0

0

0

5

30

SUPP

4

2

1369.58

422.45

12.30

-3

5

0

8

0

0

0

11

31

NOZ

3

1

1369.58

420.70

13.46

-1

1

1

22

1

0

0

9

32

NOZ

3

2

1369.58

420.95

13.46

39

1

1

22

1

1

0

9

33

COMP

16

1

1369.58

420.95

13.46

39

1

1

3

1

2

0

9

34

COMP

16

2

1369.58

421.24

13.46

21

1

1

3

1

3

0

9

35

COMP

17

2

1369.58

421.24

13.46

21

9

1

3

1

4

108

10

36

COMP

17

1

1369.58

421.70

13.37

26

9

1

3

1

5

108

11

37

COMP

22

1

1369.58

421.70

13.37

26

14

1

3

1

6

0

11

38

COMP

22

2

1369.58

422.45

14.12

28

5

1

3

1

7

0

11

39

COMP

23

2

1369.58

422.45

14.12

28

5

1

3

1

8

0

11

40

COMP

23

1

1369.58

422.45

14.42

29

5

1

3

1

9

0

11

41

COMP

24

1

1369.58

422.45

14.42

29

5

1

3

1

10

105

11

42

COMP

24

2

1369.58

422.45

15.94

30

5

1

3

1

11

105

14

43

COMP

25

1

1369.58

422.45

15.94

30

5

1

3

1

12

0

14

44

COMP

25

2

1369.58

422.45

16.82

31

5

1

3

1

13

0

14

45

COMP

305

1

1369.58

422.45

16.82

31

5

1

3

1

14

0

14

46

COMP

305

2

1369.58

422.45

17.12

32

5

1

3

1

15

0

14

47

PIPE

103

1

1369.58

422.45

17.12

32

5

1

5

1

16

0

14

48

PIPE

103

2

1369.58

422.45

17.99

33

5

1

5

1

17

0

14

49

COMP

29

3

1369.58

422.45

17.99

33

5

1

3

1

18

-73

14

50

NOZ

1

1

1363.08

420.70

13.46

-1

11

1

22

2

-23

0

3

51

NOZ

1

2

1363.08

420.95

13.46

40

11

1

22

2

-22

0

3

52

COMP

6

1

1363.08

420.95

13.46

40

11

1

3

2

-21

0

3

53

COMP

6

2

1363.08

421.24

13.46

2

11

1

3

2

-20

0

3

54

COMP

7

2

1363.08

421.24

13.46

2

12

1

3

2

-19

93

4

55

COMP

7

1

1363.08

421.70

13.37

7

12

1

3

2

-18

93

5

56

COMP

12

1

1363.08

421.70

13.37

7

15

1

3

2

-17

0

5

57

COMP

12

2

1363.08

422.45

14.12

9

2

1

3

2

-16

0

5

58

COMP

13

2

1363.08

422.45

14.12

9

2

1

3

2

-15

0

5

59

COMP

13

1

1363.08

422.45

14.42

10

2

1

3

2

-14

0

5

60

COMP

14

1

1363.08

422.45

14.42

10

2

1

3

2

-13

102

5

61

COMP

14

2

1363.08

422.45

15.94

11

2

1

3

2

-12

102

8

62

COMP

15

1

1363.08

422.45

15.94

11

2

1

3

2

-11

0

8

63

COMP

15

2

1363.08

422.45

16.82

12

2

1

3

2

-10

0

8

64

COMP

31

1

1363.08

422.45

16.82

12

2

1

3

2

-9

0

8

65

COMP

31

2

1363.08

422.45

17.12

13

2

1

3

2

-8

0

8

66

PIPE

4

2

1363.08

422.45

17.12

13

2

1

5

2

-7

0

8

67

PIPE

4

1

1363.08

422.45

17.71

14

2

1

5

2

-6

0

8

68

COMP

30

1

1363.08

422.45

17.71

14

2

1

3

2

-5

0

8

69

COMP

30

2

1363.83

422.45

18.46

15

4

1

3

2

-4

0

17

70

PIPE

3

2

1363.83

422.45

18.46

15

4

1

5

2

-3

0

17

71

PIPE

3

1

1369.11

422.45

18.46

20

4

1

5

2

-2

0

17

72

COMP

29

2

1369.11

422.45

18.46

20

4

1

3

2

-1

50

17

73

COMP

29

1

1370.05

422.45

18.46

34

4

1

3

2

1

50

16

74

PIPE

5

1

1370.05

422.45

18.46

34

4

1

5

2

2

0

16

75

PIPE

5

2

1372.83

422.45

18.46

35

4

1

5

2

3

0

16

76

6 - 10


COMP

32

2

1372.83

422.45

18.46

35

4

1

3

2

4

0

16

77

COMP

32

1

1373.58

423.20

18.46

37

6

1

3

2

5

0

16

78

PIPE

6

1

1373.58

423.20

18.46

37

6

1

5

2

6

0

16

79

PIPE

6

2

1373.58

429.05

18.46

38

6

1

5

2

7

0

16

80

COMP

33

2

1373.58

429.05

18.46

38

6

1

3

2

8

0

16

81

COMP

33

1

1372.83

429.80

18.46

36

7

1

3

2

9

0

16

82

PIPE

7

1

1372.83

429.80

18.46

36

7

1

5

2

10

0

16

83

PIPE

7

2

1365.33

429.80

18.46

18

7

1

5

2

11

0

16

84

COMP

34

2

1365.33

429.80

18.46

18

7

1

3

2

12

0

16

85

COMP

34

1

1364.58

429.80

19.21

16

8

1

3

2

13

0

16

86

COMP

35

2

1364.58

429.80

19.21

16

8

1

3

2

14

0

16

87

COMP

35

1

1364.58

429.80

19.51

17

8

1

3

2

15

0

16

88

COMP

26

2

1364.58

429.80

19.51

17

8

1

3

2

16

0

15

89

COMP

26

1

1364.58

429.80

19.58

41

8

1

3

2

17

0

15

90

NOZ

7

2

1364.58

429.80

19.58

41

8

1

22

2

18

0

15

91

NOZ

7

1

1364.58

429.80

20.58

-1

8

1

22

2

19

0

15

92

COMP

7

3T

1363.08

421.47

13.18

6

13

1

3

3

1

-55

6

93

COMP

8

1

1363.08

421.47

13.18

6

13

1

3

3

2

0

6

94

COMP

8

2

1363.08

421.47

12.93

5

13

1

3

3

3

0

6

95

COMP

9

1

1363.08

421.47

12.93

5

13

1

3

3

4

0

6

96

COMP

9

2

1363.08

421.47

12.71

4

13

1

3

3

5

0

6

97

COMP

10

1

1363.08

421.47

12.71

4

13

1

3

3

6

0

6

98

COMP

10

2

1363.08

421.47

12.46

3

13

1

3

3

7

0

6

99

COMP

11

1

1363.08

421.47

12.46

3

13

1

3

3

8

0

6

100

COMP

11

0

1363.08

421.47

12.43

-2

13

1

3

3

9

0

6

101

COMP

14

3

1362.40

422.45

15.18

1

3

1

3

4

1

-61

7

102

COMP

27

1

1362.40

422.45

15.18

1

3

1

3

4

2

0

7

103

COMP

27

0

1362.35

422.45

15.18

-2

3

1

3

4

3

0

7

104

COMP

24

3

1368.90

422.45

15.18

19

3

1

3

5

1

-42

13

105

COMP

28

1

1368.90

422.45

15.18

19

3

1

3

5

2

0

13

106

COMP

28

0

1368.85

422.45

15.18

-2

3

1

3

5

3

0

13

107

COMP

17

3T

1369.58

421.47

13.18

25

10

1

3

6

1

-36

12

108

COMP

18

1

1369.58

421.47

13.18

25

10

1

3

6

2

0

12

109

COMP

18

2

1369.58

421.47

12.93

24

10

1

3

6

3

0

12

110

COMP

19

1

1369.58

421.47

12.93

24

10

1

3

6

4

0

12

111

COMP

19

2

1369.58

421.47

12.71

23

10

1

3

6

5

0

12

112

COMP

20

1

1369.58

421.47

12.71

23

10

1

3

6

6

0

12

113

COMP

20

2

1369.58

421.47

12.46

22

10

1

3

6

7

0

12

114

COMP

21

1

1369.58

421.47

12.46

22

10

1

3

6

8

0

12

115

COMP

21

0

1369.58

421.47

12.43

-2

10

1

3

6

9

0

12

116

Design file data in IDF order —————————– Name

X

Y

Z

X

Y

Z

Occ

NOZ

33274000

10480294

501904

33274000

10480294

477520

7

in_cp Out_cp Leg Dn_occ Sg_occ 1

2

in

26

15

BLSP

33274000

10480294

477393

33274000

10480294

475615

26

1

2

in

35

15

FWN

33274000

10480294

475615

33274000

10480294

468376

35

1

2

in

34

16

E90L

33274000

10480294

468376

33274000

10480294

450088

34

1

0

in

0

16

E90L

33274000

10480294

450088

33292288

10480294

450088

34

0

2

ou

7

16

PIPE

33292288

10480294

450088

33475168

10480294

450088

7

2

1

in

33

16

E90L

33475168

10480294

450088

33493456

10480294

450088

33

1

0

in

0

16

E90L

33493456

10480294

450088

33493456

10462006

450088

33

0

2

ou

6

16

PIPE

33493456

10462006

450088

33493456

10319258

450088

6

2

1

in

32

16

E90L

33493456

10319258

450088

33493456

10300970

450088

32

1

0

in

0

16

E90L

33493456

10300970

450088

33475168

10300970

450088

32

0

2

ou

5

16

PIPE

33475168

10300970

450088

33407350

10300970

450088

5

2

1

in

29

16

T

33407350

10300970

450088

33395920

10300970

450088

29

1

0

in

0

16

T

33395920

10300970

450088

33395920

10300970

438658

29

0

3

b1

103

14

PIPE

33395920

10300970

438658

33395920

10300970

417449

103

2

1

in

305

14

FWN

33395920

10300970

417449

33395920

10300970

410210

305

2

1

in

25

14

GAT

33395920

10300970

410210

33395920

10300970

388620

25

2

1

in

24

14

Dash


STRT

33395920

10300970

388620

33395920

10300970

370078

24

2

0

in

0

14

STRT

33395920

10300970

370078

33379283

10300970

370078

24

0

3

b1

28

13

FBLD

33379283

10300970

370078

33378140

10300970

370078

28

1

0

in

0

13

STRT

33395920

10300970

370078

33395920

10300970

351536

24

0

1

ou

23

11

FWN

33395920

10300970

351536

33395920

10300970

344297

23

1

2

in

22

11

E90L

33395920

10300970

344297

33395920

10300970

326009

22

2

0

in

0

11

PSP2

33395920

10300970

326009

33395920

10300970

299847

4

1

2

in

0

11

E90L

33395920

10300970

326009

33395920

10282682

326009

22

0

1

ou

17

11

REDE

33395920

10282682

326009

33395920

10271506

328168

17

1

2

in

16

11

REDE

33395920

10277094

327089

33395920

10277094

321501

17

0

3

ta

18

12

NIP

33395920

10277094

321501

33395920

10277094

315405

18

1

2

in

19

12

GATR

33395920

10277094

315405

33395920

10277094

309817

19

1

2

in

20

12

NIP

33395920

10277094

309817

33395920

10277094

303721

20

1

2

in

21

12

CAPO

33395920

10277094

303721

33395920

10277094

303213

21

1

0

in

0

12

FWN

33395920

10271506

328168

33395920

10264521

328168

16

2

1

in

3

9

NOZ

33395920

10264394

328168

33395920

10258298

328168

3

2

1

in

0

9

T

33395920

10300970

450088

33384490

10300970

450088

29

0

2

ou

3

17

PIPE

33384490

10300970

450088

33255712

10300970

450088

3

1

2

in

30

17

E90L

33255712

10300970

450088

33237424

10300970

450088

30

2

0

in

0

17

E90L

33237424

10300970

450088

33237424

10300970

431800

30

0

1

ou

4

8

PIPE

33237424

10300970

431800

33237424

10300970

417449

4

1

2

in

31

8

FWN

33237424

10300970

417449

33237424

10300970

410210

31

2

1

in

15

8

GAT

33237424

10300970

410210

33237424

10300970

388620

15

2

1

in

14

8

STRT

33237424

10300970

388620

33237424

10300970

370078

14

2

0

in

0

8

STRT

33237424

10300970

370078

33220787

10300970

370078

14

0

3

b1

27

7

FBLD

33220787

10300970

370078

33219644

10300970

370078

27

1

0

in

0

7

STRT

33237424

10300970

370078

33237424

10300970

351536

14

0

1

ou

13

5

FWN

33237424

10300970

351536

33237424

10300970

344297

13

1

2

in

12

5

E90L

33237424

10300970

344297

33237424

10300970

326009

12

2

0

in

0

5

PSP2

33237424

10300970

326009

33237424

10300970

299847

3

1

2

in

0

5

E90L

33237424

10300970

326009

33237424

10282682

326009

12

0

1

ou

7

5

REDE

33237424

10282682

326009

33237424

10271506

328168

7

1

2

in

6

5

REDE

33237424

10277094

327089

33237424

10277094

321501

7

0

3

ta

8

6

NIP

33237424

10277094

321501

33237424

10277094

315405

8

1

2

in

9

6

GATR

33237424

10277094

315405

33237424

10277094

309817

9

1

2

in

10

6

NIP

33237424

10277094

309817

33237424

10277094

303721

10

1

2

in

11

6

CAPO

33237424

10277094

303721

33237424

10277094

303213

11

1

0

in

0

6

FWN

33237424

10271506

328168

33237424

10264521

328168

6

2

1

in

1

3

NOZ

33237424

10264394

328168

33237424

10258298

328168

1

2

1

in

0

3

End

End

End

Dash

End

End

End

Dash

6 - 12


6.2 Section 1: Basic Input Data and Raw Design File Data __________________________________________________________________________________________________________________________________________________ The first section of the HITS report consists of basic input data and raw design data. The basic input data consists of the date the report was executed, project name and a list of model names that were extracted. Each column of the raw design file data is described below. Name

If Intergraph option 61 is set to 1, the name will be the first four characters of the component item name. Otherwise, a generic item name will be output.

occ

The component database occurrence number (excluding the partition number). Note that some PIPE components have an occurrence number greater than 30000. This occurs whenever olet type components are attached to a pipe. The software breaks these pipes into multiple sections. The newly created pieces of pipe receive occurrence numbers in the 30000+ range to distinguish them from the original pipe.

cp #

The connect point number

x,y,z

The coordinate in the design file coordinate system and is not adjusted for the global origin

node

A node number assigned to all connect points other than the origin. A special node number, -1, is reserved for line endpoints. Two connect points that have the same node number are connected to each other in the model.

direct

A direction list number. The direction list number identifies all those connect points that lie together on a straight line.

sect

Section number [always 0]

flags

A bit mask used internally by the software

topo

Topos [always 0]

branch

Branch flag [always 0]

sg_occ

The segment occurrence number. All connect points belong to or are owned by a segment in the piping model. This is the occurrence number of that owner segment.


6.3 Section 2: Design File Data Sorted by Coordinate __________________________________________________________________________________________________________________________________________________ The second section of the HITS report consists of raw design file data for each connect point of the piping components that make up the network that is being extracted. The database search criteria (as defined in the options file LINE_ID_DEFINITION) from section 1 is used to find all of the appropriate segments. Once the segments are found, the software collects all of the components that are attached to the segments. Section 2 is the result of this activity. Section 2 contains several columns of data. Each column is described below: Name

If Intergraph option 61 is set to 1, the name will be the first four characters of the component item name. Otherwise, a generic item name will be output.

occ

The database occurrence number of the component (excluding the partition number). [Note that some PIPE components have an occurrence number greater than 30000. This occurs whenever olet type components are attached to a pipe. The software "breaks" these pipes into multiple sections. The newly created pieces of pipe receive occurrence numbers in the 30000+ range to distinguish them from the original pipe.]

cp #

The connect point number.

x,y,z

The coordinate in the design file coordinate system and is unadjusted for the global origin.

node

A node number assigned to all connect points other than the origin. A special node number , -1, is reserved for line endpoints. Note that two connect points that have the same node number are "connected" to each other in the model.

direct

A direction list number. The direction list number identifies all those connect points that lie together on a straight line.

sect

Always 0 here. Section number is discussed later in this section.

flags

A bit mask used internally by the software.

topo

Always 0 here. Topo’s are discussed later in this section.

branch-

Always 0 here. The branch flag is discussed later in this section.

sg_occ-

The segment occurrence number. All connect points "belong to" or "are owned" by a segment in the piping model. sg_occ is the occurrence number of that owner segment.

Section 2 is primarily used for examining the amount of data pulled in from the models through the database search criteria. Some of the data for a specific connect point is sometimes useful — particularly the occurrence number.

6 - 14


6.4 Section 3: Tracing Data __________________________________________________________________________________________________________________________________________________ Section 3 of the report, Tracing Data is a record of the actions the software is taking in building the internal data structure of the piping network. This section is primarily useful to Intergraph for investigating software problems. The last statement in section 3 states how many disconnected sections of piping exist in the network identified in the database search criteria. If the number of sections is greater than 1 then the line is not extracted and the intermediate data file is not generated. ISOGEN does not allow multiple, disconnected sections of piping to be extracted into a single iso. The following is a list of possible reasons why a network might be disconnected and some suggested solutions: 1.

The database search criteria identified more than one pipeline and the pipelines are not connected together. The solution here is to change the search criteria so that only the piping that you really want to extract is pulled in.

2.

The pipeline being extracted is incomplete and portions of it do not have components on it. The solution is to place all of the components on the line.

3.

Although the line is finished, there is a part of it that appears to be connected, but is not. For a line to be considered connected the connect points from two different components must be within 20 uors of each other. In this case you should examine section 2 of the HITS report to find a connect point whose node number is -1 (which indicates that it is a line endpoint) even though you know it should be connected to something. This is usually quite simple when the line is small. When you find the connect point, use the coordinate to view and repair the disconnected graphics. When the line is complicated, you can use section 4 of the HITS report (see the section Tracing Data) to make a sketch that identifies the disconnected point.


6.5 Section 4: Design File Data Sorted by Topo __________________________________________________________________________________________________________________________________________________ Section 4 of the HITS report is probably the most important one. This section is really a print—out of the internal data structure that represents the piping network. This data is organized on the basis of topos. A topo is a construction used to group the data representing the pipeline topology. By definition a topo is a string of piping that starts at a network endpoint or a branch point and ends at a network endpoint or another branch point. A pipeline network may consist of a single topo or dozens of topos depending upon its configuration.

Figure 6-1. Example line consisting of one topo. The line in Figure 6-1 consists of one topo because it does not contain any branch points. The beginning of the topo is a line endpoint as is the end of the topo.

Figure 6-2. Example line consisting of two topos

6 - 16


The line in Figure 6-2 contains two topos due to the branch component in it (the tee). The first topo consists of the line from endpoint 1 to endpoint 2 (the header of the pipeline). The second topo consists of the piping from the center of the tee to line endpoint 3.

Figure 6-3. Example line consisting of three topos The line in Figure 6-3 contains three topos because there are two branches in it. The first topo again consists of the line from endpoint 1 to endpoint 4. The second topo consists of the line from connect point 1 of weldolet 1 to endpoint 2. The third topo consists of the line from connect point 1 of weldolet 2 to endpoint 3.

Figure 6-4. Topo’s on a line that contains a loop The line in Figure 6-4 consists of two topos. One topo is comprised of the line header from endpoint 1 to endpoint 2. The other topo starts at the center of one tee and goes to the center of the other tee.


The data in section 4 of the HITS report is sorted primarily by topo number. At the very beginning there are several lines where the topo number is zero. These are component origins which do not receive topo numbers or node numbers — they should be ignored. Subsequent to the lines where the topo number is zero are lines for the first, second and subsequent topos. The secondary sort key for the data in section 4 of the report is node number. Thus, within a topo the data is sorted by node number. This results in connect points with the same node number being adjacent to each other in the report. The result is that section 4 of the HITS report contains a trace of each topo of the line. Example 1: The following is an excerpt from a HITS report section 4:

Name

cp#

node

E90L E90L PIPE PIPE E90L E90L PIPE PIPE GATR GATR PIPE PIPE

1 2 1 2 2 1 2 1 1 2 1 2

-1 1 1 2 2 3 3 4 4 5 5 -1

topo 1 1 1 1 1 1 1 1 1 1 1 1

This trace consists of a single topo. The first endpoint is connect point 1 of a 90 degree elbow. Connect point 2 of the elbow is connected to connect point 1 of a pipe. Following this logic, the sequence of components starting from the top is: elbow -> pipe -> elbow -> pipe -> valve -> pipe. This same procedure may be followed to sketch out each network topo. Topo sketches are useful if you are interested only in the sequence of components in a particular region of the line. If you are interested in the entire network, connect the topos together. The topos are connected together by the branch column in section 4 of the report. The branch column is used together with the last column. The last column in section 4 is a report line number. You can see by looking back at Figure 6-1 that the last column starts out at 1 and is incremented for each line in section 4. When the branch column contains a nonzero value then this indicates that the node is a branch point. The value of branch refers you to the line number of the report where the connecting topo begins. Example 2: The following is an excerpt from a HITS report section 4:

Name

occ#

cp#

node

topo

branch

PIPE PIPE PIPE

10 10 30001

1 2 1

-1 1 1

1 1 1

0 5 5

1 2 3

6 - 18


PIPE WOL WOL PIPE PIPE

30001 15 15 35 35

2 1 2 1 2

2 1 3 3 -1

1 2 2 2 2

0 -2 0 0 0

4 5 6 7 8

The network is composed of two topos. Topo 1 is simply two pipes. Topo 2 consists of a weldolet connected to a piece of pipe. Note that the occurrence number of the second pipe in topo 1 indicates the model contains a single pipe which the software split into two at the olet. Figure 6-5 shows the Network for Example 5.

Figure 6-5. Network for Example 2 The value for branch at node 1 is 5. Looking at line 5 in the report we see that it is the first line of topo 2. Thus topo 2 connects to topo 1 at node 1. This is confirmed by the fact that the node numbers where topo 2 connects to topo 1 match. That is, the WOL cp1, PIPE (occ 10) cp2, and PIPE (occ 30001) cp1 are all node number 1. The value of branch for cp1 of the WOL is -2. The negative sign indicates that this is a "back pointer". The back pointer is exactly the same as any other branch value except that it (usually) points back to a previous topo rather than forward to a subsequent topo. Note that where two or more topos are connected together the branch numbers must agree. In Example 5 they do. The back pointer on topo 2 points back to line 2 while the forward pointer on topo 1 points to line 5. In Example 2, the branch flag pointed to the start point of the connecting topo. It can also happen that the branch flag points to the endpoint of the connecting topo. In this case you traverse the topo in reverse order. Example 3:

Name

PIPE PIPE 90E 90E PIPE PIPE

occ#

10 10 35 35 46 46

cp#

node

topo

branch

1 2 2 1 1 2

. . . 20 21 21 22 22 23

3 3 3 3 3 3

0 0 0 0 0 53

20 21 22 23 24 25


PIPE PIPE

30003 30003

1 2

PLUG PLUG BLV BLV NIPL NIPL SOL SOL

76 76 82 82 103 103 110 110

2 1 1 2 2 1 2 1

23 24 . . . -1 10 10 11 11 12 12 23 . . .

3 3

53 0

26 27

7 7 7 7 7 7 7 7

0 0 0 0 0 0 0 -25

46 47 48 49 50 51 52 53

In Example 3, topo 3 consists of pipe, elbow, pipe, pipe. Topo 7 is a typical drain assembly— plug, block valve, nipple, sockolet. Topo 7 connects to topo 3 at line 53 in the report (the value of branch on line 25 is 53 and the value of branch of line 53 is -25). In this case, the value of branch on topo 3 points to the bottom of topo 7 and the network structure is obtained by moving up topo 3 rather than down (See Figure 6-6).

Figure 6-6. Network for Example 3 Example 4: The following data is from section 4 of a HITS report:

Name 90E 90E PIPE PIPE FLWN FLWN GAT GAT FLWN FLWN T

Occ 37 37 101 101 22 22 54 54 11 11 36

cp#

Node

Topo

1 2 1 2 2 1 1 2 1 2 1

-1 1 1 2 2 3 3 4 4 5 5

1 1 1 1 1 1 1 1 1 1 1

Branch 0 0 0 0 0 0 0 0 0 0 15

1 2 3 4 5 6 7 8 9 10 11

6 - 20


T PIPE PIPE T PIPE PIPE

36 11 11 36 12 12

2 1 2 3 1 2

6 6 -1 7 7 -1

1 1 1 2 2 2

15 0 0 -11 0 0

12 13 14 15 16 17

In Example 4, the tee is slightly different from the olet type components. Branch flags are set on both connect points 1 and 2 of the T and the node numbers do not match where topo 2 connects to topo 1. This is a consequence of the fact that node numbers are not assigned to component origins. See Figure 6-7 which shows the Network for Example 4.

Figure 6-7. Network for example 4 Example 5:

Name PIPE PIPE REDE REDE PIPE PIPE SOL SOL PIPE PIPE PIPE PIPE

Occ 23 23 24 24 13 13 56 56 42 42 26 26

cp# 1 2 1 2 1 2 1 2 1 2 1 2

Node

Topo

-1 1 1 2 2 -1 3 4 4 -1 5 -1

1 1 1 1 1 1 2 2 2 2 3 3

Branch 0 0 7 11 0 0 -3 0 0 0 -4 0

1 2 3 4 5 6 7 8 9 10 11 12

In Example 5, topo 1 consists of a pipe connected to an eccentric reducer which in turn is connected to another pipe. Notice, however, that the branch flag is set to two different numbers on the reducer. This indicates that the reducer is tapped twice. The branch flag on the first connect point points to the topo connected at the first tap while the branch flag on the second connect point points to the topo connected to the second tap. A tap is always a branch starting point and thus is always the start point of a new topo. Refer to Figure 6-8, which shows the network for Example 5.


Figure 6-8. Network for Example 5 If you generate some HITS reports and practice sketching out the pipeline networks, you will become familiar with the report contents and better understand the concepts presented in the examples above.

6 - 22


6.6 Section 5: Design File Data in IDF Order __________________________________________________________________________________________________________________________________________________ Section 5 of the HITS report contains a record of how the network is traversed as the intermediate data file is being generated. The software examines the network of piping and chooses the best (that is, the one least likely to result in problems from ISOGEN) topo to begin the network traversal on. ISOGEN prefers certain navigation sequences over others and the interface software tries to choose the optimal sequence. ISOGEN also requires that the traversal of the network be branch first order. This means that whenever a branch is encountered in the network, the traversal must head down the branch before continuing down the header. To traverse the network in branch first order manner you start on the header topo and travel connect point by connect point until the value of branch is greater than 0 at some node. When branch is positive then you jump down to the new topo and start traversing it until you come to another branch or to the end. If you encounter another branch then you must jump again to another topo. When the end of the topo is found then you return to the topo from which you jumped and continue tracing. Example 6: The following is an example of a network:

Name PIPE PIPE T T PIPE PIPE T PIPE PIPE

Occ 10 10 11 11 12 12 11 13 13

cp# 1 2 1 2 1 2 3 1 2

Node

Topo

-1 1 1 2 2 -1 3 3 -1

1 1 1 1 1 1 2 2 2

Branch 0 0 7 7 0 0 -3 0 0

1 2 3 4 5 6 7 8 9

In Example 6, topo 1 consists of a header, two pipes, and the run of a tee. Topo 2 consists of a branch, the branch leg of a tee and a branch pipe. Following the rules given above for traversal of the network would yield the following trace:

Name PIPE T T PIPE T PIPE

Occ 10 11 11 13 11 12

cp in 1 1 0 1 0 1

cp out

Leg

2 0 3 2 2 2

1 1 2 1 4 1


Step 1 travels from one end of the first pipe to the other. Following the first pipe we travel into the tee. Notice that although the origins do not have node numbers they appear in the traversal whenever a change in direction occurs. This means that, for the tee, the traversal occurs from connect point 1 to the origin in step 2. At this point the branch flag is positive and so a jump occurs to topo 2. On topo 2 we travel from the origin of the tee to connect point 3 (which is the branch connect point) in step 3. In step 4 we travel down a pipe which is the last component on the topo. We then jump back to topo 1 and in step 5 travel from the tee origin to connect point 2. Finally, in the last step we traverse the remaining pipe on topo 1. Refer to Figure 6-9 for an illustration of this traversal. The header topo number can be found by examining the first line in the traversal. In this case the first line consists of PIPE — occurrence 10. Looking at the network description, observe that PIPE — occurrence 10 is on topo number 1. This makes topo 1 the header topo.

Figure 6-9. Traversal in Example 6 In ISOGEN terminology one step in the above trace is termed a component leg. Straight through components like pipe, flanges, and valves consist of one leg. Change of direction components like elbows, angle valves and so on consist of two legs. Branch components like tee’s, olets, 3-way and 4-way valves and crosses consist of three or four legs. In Example 9, the last leg of the tee is given a leg number of 4. By definition only 4-way components have a leg 3 (which would correspond to the 2nd branch leg). Branches off from components formed by taps are termed branch legs and are not given a number. Branch legs are treated as other branches are though. When a tapped component is encountered in the network then all the tapped legs must be traced before continuing down the topo. Although olet type components have a different connect point skeleton than tee’s do they are treated similarly in the network trace. This is highlighted in the next example:

6 - 24


Example 7: The following is a network:

Name

Occ

90E 90E PIPE PIPE PIPE PIPE WOL WOL PIPE PIPE

8 8 10 10 30001 30001 6 6 9 9

cp# 1 2 1 2 1 2 1 2 2 1

Node

Topo

Branch

-1 1 1 2 2 -1 1 2 2 -1

1 1 1 1 1 1 2 2 2 2

0 0 0 7 7 0 -4 0 0 0

1 2 3 4 5 6 7 8 9 10

The network trace for this network is:

Name

Occ

90E 90E PIPE WOL WOL PIPE WOL

8 8 10 6 6 9 6

cp in

cp out

leg

1 0 1 1 1 2 1

0 2 2 1 2 1 1

1 2 1 1 2 1 4

In Example 7, the first leg of the olet goes from connect point 1 to connect point 1. It is analogous to the step with the tee where traversal goes from connect point to the origin. In this case the traversal does not go anywhere and therefore is called a zero length leg. The second leg traverses from cp1 to cp2 — analogous to the previous example’s traversal from the tee origin to cp3. After the branch topo has been traversed we return to the olet for leg 4 which again goes from cp1 to cp1 — another zero length leg. This step is analogous to going from the origin to cp3 in the previous example. Notice also the traversal through the elbow. Since the elbow causes a change of direction, it is traversed in two legs: 1) from cp1 to the origin and 2) from the origin to cp2. Sometimes the traversal of the network requires traveling into the branch leg of a branch component. When this happens the leg numbers are assigned somewhat differently on the branch component. Example 8: The following is a partial network:

Name

PIPE

Occ

cp#

10

1

Node

Topo

. . . 20

4

Branch

0

46


PIPE T

10 15

2 3

PIPE PIPE T T PIPE PIPE

12 12 15 15 17 17

1 2 1 2 2 1

21 21 . . . -1 52 52 53 53 -1

4 4

0 -61

47 48

7 7 7 7 7 7

0 0 48 48 0 0

59 60 61 62 63 64

In Example 8, a lower numbered topo (topo 4) contains a back pointer to a higher numbered topo (topo 7). Whenever this happens, the traversal will enter branch. The trace for this part of the network would be:

Name

Occ

PIPE T T PIPE T PIPE

10 15 15 12 15 17

cp in 1 3 0 2 0 2

cp out 2 0 1 1 2 1

leg 1 1 2 1 4 1

In this example, the branch leg of the tee is leg 1 since it is traversed first. Legs 2 and 4 are assigned arbitrarily in this situation and so tracing may go either way (ISOGEN has no preference). Refer to Figure 6-10 which shows this network traversal.

Figure 6-10. Network traversal in example 8

6 - 26


6.7 Using the HITS Report to Solve Problems __________________________________________________________________________________________________________________________________________________ When you have difficulty extracting a line, the first thing you should do in analyzing the problem is to sketch out the network. Often this is enough to identify the problem. If the structure in section 4 of the report is incorrect — that is, the topos are not correctly defined and connected or the pointers appear incorrect — then ISOGEN’s input will be wrong and the drawing will definitely be incorrect. When the data structure represented in section 4 of the report is incorrect then you can conclude that either the interface has a bug or there is a problem in the model. Typical model problems include such things as disconnected sections and overlapping components or pipes. When the modeler has inadvertently placed two pipes on top of each other you will get an error message at the top of the HITS report stating this. The message will also report a node number where the problem was detected. By getting the coordinate of the node you can pinpoint where in the model the problem occurs. This can also occur where the connect points of components overlap each other and are not properly connected. Notice that one of the columns in section 4 of the report is called section. In a correct network all of the topos should have a value of 1 in this column. When the network is composed of multiple disconnected sections, however, some topos will contain a value other than 1. In this case the network for each section should be sketched out. It should be apparent after doing this where the different sections should have been connected in the model and, therefore, where the trouble spot is. Another problem that might occur is that components that should all be colinear are not. This is detected by examining the direction list number. If the direction list changes for example from one pipe to another then a problem exists in the model and the line can not be extracted properly. Mismatches between the design file and database can also cause iso extraction failures but these types of problems should be trapped and reported adequately in other areas of the software. You should not need to rely on the HITS report to find these kinds of problems. When the data structure in section 4 of the report is correct then the traversal in section 5 should be examined. Even if the network is correct, some other bug can cause the network traversal to fail. Again, if the traversal is incorrect then ISOGEN will definitely fail. When both the network and the traversal are correct, there is most likely a problem with ISOGEN. When ISOGEN is at fault, then one of the following scenarios is true: 1.

The drawing appears correct for the most part but some aspect of it is incorrect. When this happens there is usually some option or combination of options that have been enabled that resulted in the problem. The best way to find the cause of the problem is to start with a basic drawing generation setup that contains few "special" options. Then add a few options at a time until the problem is reproduced. Finally, through a process of elimination identify the option that is causing the problem. All failures of this type should be reported to Intergraph.


2.

The drawing or one sheet of it is scrambled — a total failure. When this happens it is usually the case that disabling options will not result in the drawing working — though sometimes it does. The best thing to do when this happens is to try and reextract a smaller portion of the line if possible. The failure should also be reported to Intergraph. When any sheet of an ISOGEN drawing fails, ALL sheets from the same pipeline may contain errors and are suspect.

6 - 28


The Options File 7 - 1

7. The Options File

__________________________________________________________________________________________________________________________________________________

The options file consists of a set of options and tables that drive the interface to ISOGEN. You can modify the options file to customize the drawings that are produced by ISOGEN. See the appendices for an example of an options file. Information contained in the remainder of this manual assumes that you have knowledge of the following: The PDS database structure

PDS Reference Database The Label Description Library Utility The Standard Note Library Material Description Libraries

7-2


7.1 File Structure __________________________________________________________________________________________________________________________________________________ The options file is composed of two sets of options and several tables. Each option block and table is preceded in the options file by a keyword that identifies it. The keyword must begin in column 1 and should NOT be surrounded by single quotes. The keywords and data that follow them can appear in any order in the options file. You can put comments to the right of any table entry but not to the right of a keyword. You can also have comments preceding any keyword or following the last entry in a table. Comments either preceding a keyword or following the last table entry must have an exclamation point (!) in column 1 to identify it as a comment. Keywords are always followed by a number - starting in any column - that identifies the number of table entries. It is valid for the number to be zero, indicating that there are no table entries. If the number that precedes a table does not match the number of entries in the table, a warning message is generated at the time the table is read in. Entries in tables consist of a row of numbers and sometimes character strings that are separated by commas ( , ). Character strings that are part of a table entry MUST be surrounded by single quotes (’ ’). A typical table in the options file might appear as:

TABLE_KEYWORD nrows n1, n2, ’c1’, n3, ... . . . m1, m2, ’cm’, m3, ...

Where: TABLE_KEYWORD

is the table key word discussed above.

nrows

is the number of table entries.

n1, n2, ...

are numbers in the first table entry.

’c1’

is a character string in the first entry.

m1, m2, ...

are numbers in the last table entry.

’cm’

is a character string in the last entry.

The options file keywords consist of the following: ISOGEN_OPTIONS_BLOCK INTERGRAPH_OPTIONS_BLOCK FILES


USER_DEFINED_WELDS WELD_PREFIX DETAIL_SKETCH_FACILITY PIPELINE_HEADER ATEXT_SPECIFICATIONS INGR_ATEXT_SPECIFICATIONS LINE_ID_DEFINITION TYPE_1_LABELS TYPE_2_LABELS TYPE_3_LABELS START_POINT_NOTES SECONDARY_ORIENTATION_NOTE END_POINT_COMPONENT_LABELS NOZZLE_NOTE DOTTED_SYMBOLOGY_CODE_LIST_VALUES NOMTO_CODE_LIST_VALUES SHOP_FABCAT_CODE_LIST_VALUES OFFSHORE_FABCAT_CODE_LIST_VALUES MOVABLE_TEXT NEW_SYMBOL_KEYS GENITM_NOTE_FORMAT ALTERNATE_DESCRIPTION_INDEX USER_DEFINED_IMPLIED_ITEM_BOM USER_DEFINED_GENERATED_ITEM_BOM USER_DEFINED_COMPONENT_BOM NON_DIMENSIONED_SUPPORTS When an option in an option block is set to 1, it is enabled.

7-4


7.2 ISOGEN_OPTIONS_BLOCK __________________________________________________________________________________________________________________________________________________ The ISOGEN options block is a group of options that are input directly to ISOGEN. These options do not effect the ISOGEN interface but, control the different characteristics of drawing output. However, some options selected in the ISOGEN options block might require that entries be defined in certain of the options file tables in order to work properly. The ISOGEN options block consists of 140 numbers arranged in 10 rows of 14. Each number is referred to as a "word" in the options block. Row 1 contains words 1 through 14, row 2 contains 15 through 28 and so on. The positioning of a number within a word is important. Thus, in editing the options block be sure to keep the units digit of the entry in the same column. The following options should not be changed from their default settings. These options are not used in the Intergraph environment. Words ______

Function _________

1 7 31 32 33 43-51 55-57 58 131

Plot length control Drawing control Iso output file Plotter scale factor Pipe detailed Wastage factors Diagnostic printing Clear screen Test parameter Be careful when changing words 34 (picture scale) and 38 (split control). Values other than the default sometimes result in drawing failure.

Be careful modifying words 115 (angular tolerance) and 116 (linear tolerance). Large values of these options can cause sloped lines to be shown incorrectly.

The Drawing control option (word 7) must be left at 0. ISOGEN will sometimes fail if forced to put more information on a sheet than it determines it can fit. You can minimize the number of sheets produced by increasing the sheet size.

Option 8 (dimension line distance) does not work when it is set to give a dimension standout greater than 25 mm.

In general, ISOGEN is more successful with a large sheet size than a small one.


You can create virtually any size sheet - including one with a user-defined title block by using the drawing margin options (words 10-13) and the drawing size options (words 14-16). User-defined graphics in reference files must be positioned in drawing margins or in a reserved strip along the bottom of the drawing (option 35) in order for stacking of multisheet drawings to work properly.

ISOGEN drawing layout

7-6


7.3 INTERGRAPH_OPTIONS_BLOCK __________________________________________________________________________________________________________________________________________________ The Intergraph options block is a group of options, numbered in the same way as the ISOGEN options (Appendix B), that directly control the actions of the ISOGEN interface. The specific meaning of each option is outlined below: Word _____

Value ______

Meaning _ _______

1

0 1

Do not produce the ISOGEN MTO neutral file. Produce the ISOGEN mto neutral file. (isoname.bom)

2

0

THIS OPTION MUST BE SET TO ZERO

3

0 1

Do not produce the ISOGEN printed parts list. Produce the ISOGEN printed parts list. (isoname.prt)

4

0

Do not produce the ISOGEN component vrs sheet number file. This setting will not split the MTO neutral file. Produce the ISOGEN component vrs sheet number file, isoname.sed. If the MTO map file includes component occurrence numbers and record types, this setting splits the MTO neutral file by sheet. Neutral files created by the split are named: isoname(sheet#).b(extnum).

1

5

0 1

Do not produce the ISOGEN cut pipe report. Produce the ISOGEN cut pipe report. (isoname.cut)

When any of options 1-5 are set 0 (not generating a file), the files are in fact still created. However, the command procedures which run ISOGEN delete these files after the drawing is generated.

6

0

Disable the "CONNECTION NOT FOUND" message at line endpoints where no connecting component is found.


7

1

Enable "CONNECTION NOT FOUND" message at line end points where no connecting component is found. (Does not apply to plugs, caps, and blind flanges.) This option can be used to highlight the fact that no connecting component was found at a line endpoint. When no connecting component is found then implied materials cannot be generated at that endpoint. This option can make checking of the drawings easier.

0

Do not adjust connect point coordinates to the face-of-flange.

1

Adjust connect point coordinates to the face-of-flange. In the piping model, component connect points are placed midway through the gasket at flanged connections. When this option is disabled, dimensioning on the iso also goes to the center of the gasket. When the option is enabled, dimensioning is to the face-of-flange.

7-8


8

Position A

Bolt Length This Intergraph option has multiple switch settings (such as A, B, C, D). Intergraph switch settings are read from right to left (D-C-B-A). For example, if this option is set to 21, 1 represents switch position A and 2 represents switch position B. When setting an option with multiple switches, leading zeros may be omitted, but trailing zeros must be included.

0

Output bolt lengths in inches in the BOM printed on the iso.

1

Output bolt lengths in millimeters in the BOM printed on the iso.

Position B

Bolt Diameter

0 or blank

Output bolt diameter in the default units (as defined in ISOGEN option switch 41 and Intergraph option 43) in the BOM printed on the iso. When using this setting, AText -359 must be left blank.


1

Output bolt diameter in inches in the BOM printed on the iso. This setting overrides the setting defined with ISOGEN switch 41 (position A). When using this setting, AText -359 should be set to NPD and ISOGEN switch 65 (position B) must be set to 1.

2

Output bolt diameter in millimeters in the BOM printed on the iso. This setting overrides the setting defined with ISOGEN switch 41 (position A). When using this setting, AText -359 should be set to NPD and ISOGEN switch 65 (position B) must be set to 2.

9

val

Tolerance for considering valve operators and eccentric reducers to be skewed. Val is the maximum direction cosine times 1000. The default value is 10 (or .01).

10

0

The commodity code description includes consideration of component schedule. Therefore, do not append the component schedule to the material description

1

Commodity code description does not include consideration of schedule. Therefore, the component schedule is appended to the material description.

Option 10 is not needed if label description library numbers, which output schedules, are embedded ([ ]) within material descriptions found in the Material Description Library. During extraction, the labels are expanded in the material description. For more information on the Label Description Library and the Material Description Library, refer to the Reference Data Manager document.

The material description for an elbow appears as follows in the material description library where label 403 is defined to Output Component Schedule:

"WELD ELL BE [403] CS ASTM A234-WPB"

7 - 10


At extraction time, the label description library number [403] is expanded so that the description placed in the drawing is:

"WELD ELL BE STD WT CS ASTM A234-WPB"

These embedded attributes can also be included in the material descriptions for implied items like bolts and gaskets. 11

val

Piping component connection tolerance in uor’s. The default value is 20 uor’s. If the space between connect points is greater than the value defined by this option, the pipes/components are not considered connected.

12

val

Number of characters after which a line feed should be inserted in instrument tag numbers for display in an instrument bubble. (See also ISOGEN option number 123.) The following example assumes that the instrument tag number is INST-001.

1

When set to 1, a line feed is inserted after the first character.

10

Replace an embedded dash within the tag number with a linefeed.


13

0 1

14

Display all valve operators on the isometric regardless of whether or not they are displayed in the piping model. Do not display valve operators on the isometric that are turned off within the model. NOTE: This option can also be used in conjunction with Intergraph options 59 and 48 that deal with valve operator display and orientation notes.

0

Generate implied materials. These include bolts, gaskets and field welds.

1

Do not generate implied materials.

7 - 12


This option allows you to do testing without incurring the overhead of generating implied materials. Execution of the ISOGEN interface takes a significantly longer time when bolts and gaskets must be generated. 15

16

0

Spool Numbering On (Uses consecutive numbering)

1 10

Spool Numbering Off Spool Numbering On (This option uses consecutive numbering with the exception that spool numbering is set back to 1 for each new sheet.)

0

Generate the HITS report and the intermediate data file.

1

Generate only the HITS report. When generating only a HITS report an iso cannot be generated since no input to ISOGEN is produced.

2

Generate only the intermediate data file for batch extraction. (DO NOT generate the HITS file) Setting two should only be used with batch extraction. If DEBUG is ON for batch extraction, position A is reset to 0. The HITS file is automatically generated when using interactive extraction.

17

0 1

18

0 1 3

Continue trying to extract the line if a component is encountered that is not in the PDS to ISOGEN symbol map. Stop extraction if a component is encountered that is not in the PDS to ISOGEN symbol map. Generate coordinates in the DESIGN VOLUME coordinate system. Generate coordinates in the PLANT coordinate system. Generate coordinates in the DESIGN VOLUME coordinate system using large coordinates.


4

Generate coordinates in the PLANT coordinate system using large coordinates. Option 3 or 4 should be used if any coordinate can be outside the range plus or minus 13.3 miles in an English project or plus or minus 21.4 kilometers in a metric project. NOTE: Coordinate System data is stored in the type 63 data of the piping model. For Interactive Extraction, the software reads the type 63 of the first model entered on the form. For Batch Extraction, the software reads the type 63 data from the first piping model in the area specified in each record of the batch input file.

19

1

THIS OPTION MUST BE SET TO 1.

20

0 1

Do not generate an Intergraph mto neutral file. Generate an Intergraph mto neutral file. The naming convention: isoname+sheet number.b# (where # is the extraction number) is used when an Intergraph mto neutral file is generated. MTO neutral file generation is discussed in detail in the section The MTO Neutral File Record Map. NOTE: Intergraph option 4 must be set to 1 in order to generate an mto neutral file.

21

22

0 1

Do not generate welds in the mto neutral file. Generate welds in the mto neutral file where the welds listed on the mto do not appear on the corresponding isometric sheet.

2

Generate welds in the mto neutral file where the welds listed on the mto appear on the corresponding isometric sheet. As a result, using this option setting slightly increases run time and generates a larger intermediate data file.

0 1

Extract by substring of the line name attribute. Extract by equality of the line ID attributes. The meaning of this option is discussed at length in the section Interactive Isometric Generation. NOTE: Option 22 must be set to 1 when running batch isometric extractions

23

0

Use the system-defined nozzle connection note. The system-defined nozzle connection note is formatted as follows: NOZ: xxx - where xxx is the nozzle tag ITEM: xxx - where xxx is the equipment tag size-rating-facing

7 - 14


1

Use the NOZZLE_NOTE table in the options file to form the nozzle connection note.

24

0 1

Generate pipe supports in the intermediate data file. Do not generate pipe supports in the intermediate data file.

25

0

Show bare branch weld as a length of pipe - with coordinate label pointing to CP2 of branch weld.


1

26

Position A

Show bare branch weld as a dot - with coordinate label pointing to CP1 of branch weld.

Inspection Number This Intergraph option has multiple switch settings (such as A, B, C, D). Intergraph switch settings are read from right to left (D-C-B-A). For example, if this option is set to 21, 1 represents switch position A and 2 represents switch position B. When setting an option with multiple switches, leading zeros may be omitted, but trailing zeros must be included.

0 1 2

27

Inspection Numbers Do not extract inspection numbers. Extract inspection numbers. Do not display blank inspection number. Extract inspection numbers. Display blank inspection numbers as defined by INGR_ATEXT_SPECIFICATION 16 (default as ****).

Position B

Inspection Number Enclosure Type

0 1 2 3 4 5

bubble (default) rectangle rectangle with arrowed ends rectangle with rounded ends triangle diamond

0 1

Generate component tags as -37 records in the intermediate data file. Generate component tags as -22 records in the intermediate data file. This option must be set to 1 in order to generate instrument bubbles properly on both in-line and off-line instruments.

7 - 16


28

0

Do not replace the ISOGEN instrument dial symbol (IDPL or IDFL) with the instrument balloon.

1

Replace the ISOGEN instrument dial symbol with an instrument balloon.

Regardless of which setting is used, the instrument tag number is displayed inside of a circle. 29

0

Do not make off-line instruments no-mto.


1

Make all off-line instruments no-mto.

Offline instruments are defined as any instrument mapped to the ISOGEN symbol IDPL or IDFL. 30

0

Do not show reinforcing pads in the ISOGEN BOM.

7 - 18


1

Show reinforcing pads in the ISOGEN BOM.

A reinforcing pad can only be shown in the ISOGEN BOM when the PDS branch component in the model is mapped to the ISOGEN component named TERF. The component in the model should have the commodity code and material description for the reinforcing pad. 31

0 1

Do not access the VALOPR table to map PDS symbol names and valve operator names to ISOGEN symbols. Access the VALOPR table to map PDS symbols and valve operators to ISOGEN symbols. This option is provided because there are two ways to map a PDS symbol and valve operator to an ISOGEN symbol. One way is through the VALOPR table described in the section The Valve/Operator Table. The other way is through the PDS-to-ISOGEN symbol map discussed in the section The PDS-to-ISOGEN Symbol Map. When this option is set to 1, the ISOGEN symbol name obtained from the symbol map is replaced by an entry in the VALOPR table if it exists.


32

0

Do not generate implied materials from the reference database using table 212.

1

Generate implied materials from the reference database using table 212.

This option must be enabled (set to 1) in order to generate implied materials in the mto neutral file and/or to generate a note on the drawing for the implied materials. Also, see Intergraph option 45. NOTE: The generation of implied items from the Implied Material Data Table is triggered by special definitions you make in the reference database. Refer to the Reference Data Manager document for details.

7 - 20


Refer to the Material Take-Off Options material in the Project Administrator’s Reference Guide for more information. Material Takeoff Options that could effect the implied material output on the iso are stored in the type 63 data of the piping model. For Interactive Extraction, the software reads the type 63 of the first model entered on the form. For Batch Extraction, the software reads the type 63 data from the first piping model in the area specified in each record of the batch input file. 33

0 1

Do not generate chain wheel operators, extension stems or floor stands. Generate chain wheel operators, extension stems and floor stands. Output information is based on the setting of INGR Word 45. This option must be set in order to generate chain wheel operators, extension stems and floor stands in the mtoneutral file or to generate a note on the drawing. The generation of chain-wheel operators, extension stems and floor stands is triggered by definitions you make in the model for specific valves. Refer to the Piping Design Graphics Reference Guide for details on making these definitions. For these items the material description library is accessed by adding the operator number to the following strings:

Item _____

Prefix ______

Example _ _______

Chain Operators Extension Stems Floor Stands

CHAIN_ XSTEM_ FSTAND_

CHAIN_1001 XSTEM_2001 FSTAND_3001

34

0 1

Do not generate the title block data files. Generate the title block data files. The title block data files are used by the batch extraction software to fill out drawing title blocks. If this option is enabled you must also specify a title block tables File under the FILES section of the options file (refer to The Files Table, page 7 - 42 for more information).

35

THIS OPTION MUST BE SET TO ONE.


36

0

Do not remove unexpanded attribute specifications from material descriptions.

1

Remove unexpanded material descriptions from material descriptions.

This option allows you to remove any embedded attribute specifications (labels) that are not expanded when the material description is generated. Thus, if a material description contains labels that refer to unrelated tables, the unused label can be removed from the description. However, labels that cannot be expanded because of error will also be removed - leaving the description incomplete although it may appear complete on the drawing.

7 - 22


37

0

Disable use of the alternate index into the material description libraries.

1

Enable use of the alternate index into the material description libraries.

This option allows you to access the material description libraries by using an attribute other than commodity code or specialty tag number. Library access is first attempted using the commodity code or tag number. If no material description is found, the attribute defined in the ALTERNATE_DESCRIPTION_INDEX table (discussed in the section ALTERNATE_DESCRIPTION_INDEX) is used to retrieve a description from the appropriate library. This option also allows you to establish a generic description for instruments, specialties and pipe supports. This can be used as an alternative to creating a material description library entry for each item.


38

val

Format of date strings output in the title block text files. Set val as follows: 0 - DD-MMM-YYYY 1 - DD-MMM-YY 2 - MM/DD/YY 3 - DD/MM/YY

4 - MMM DD, YYYY 5 - DD MMM YYYY 6 - MM/DD 7 - DD/MM

39

0 1

Disable flow arrows on pipe. Enable flow arrows on pipe.

40

0 1

Assign pipe flow arrows during traversal. Assign pipe flow arrows by segment. When assigned during traversal, the first pipe receives a flow arrow. Arrows are then generated on the first pipes downstream of branch components. When assigned by segment, the first pipe encountered on each segment receives a flow arrow.

41

0

Disable multi-endprep components.

1

Enable multi-endprep components.

This option controls the display of end-prep graphics on components that have more than one end-prep such as the flanged and welded valve shown above.

7 - 24


42

0

Disable boxed tag numbers on commodity items.

1

Enable boxed tag numbers on commodity items. This option allows you to show tag numbers on the isometric for commodity items (that is, items other than specialty items, instruments and pipe supports).

43

0 1 2

Output all bores in inches on the isometric. Reserved for future use Output all bores in millimeters on the isometric.


NOTE: The settings for Intergraph option 43 should correspond with the settings for ISOGEN Option 41, Position A (Dimensional Units). 44

0

THIS OPTION MUST BE SET TO ZERO.

45

val

These options determine how implied materials from the reference database (212) (other than bolts and gaskets) are handled.

0

Do not generate either a note in the drawing (based upon the GENITM_NOTE_FORMAT table) or an entry in the ISOGEN bill of material.

1

Generate an entry in the bill of material, but not a note in the drawing.

7 - 26


2

Generate a note in the drawing based upon the GENITM_NOTE_FORMAT table, but not an entry in the bill of material. (This option does not apply to implied items from the spec.)

3

Generate a note in the drawing and an entry in the bill of material. (This option will not result in a note for implied items from the spec.)


NOTE: Material Takeoff Options that could effect the implied material output on the iso are stored in the type 63 data of the piping model. For Interactive Extraction, the software reads the type 63 of the first model entered on the form. For Batch Extraction, the software reads the type 63 data from the first piping model in the area specified in each record of the batch input file. 46

0 1

Do not label the drawing with segment node numbers. Label the drawing with segment node numbers for those segments where data originated from the P&ID.

47

0

Do not generate weight information in the BOM on the face of the iso. Generate weight information in the BOM on the face of the iso using Imperial Units (raw weight). Generate weight information in the BOM on the face of the iso using Metric Units (raw weight).

1 2

NOTE: Raw weight implies that the insulation of the component is not included. Intergraph option 47 should be used in conjunction with ISOGEN option switch 41. 48

0

Disable secondary orientation notes for valve operators.

1

Enable secondary orientation notes. See also the section SECONDARY_ORIENTATION_NOTE.

7 - 28


49

0


50

0

Disable induction bend groups.

1

Enable induction bend groups. NOTE: For Intergraph option 50 to function properly, pipes and pipe bends must be grouped so that they are included in an induction bend group with the Data/Revise/Component Group command from within PD_DESIGN.


51

val

Nozzle connection tolerance scaling factor. The default nozzle connection tolerance is 4 mm. The default will be scaled according to the val entered divided by 100. Thus, to double the tolerance set val to 200.

52

0

Do not append the number of nuts per bolt to the material description of bolts. Append the number of nuts per bolt to the material description of bolts.

1

NOTE: INGR_ATEXT_SPECIFICATIONS ATEXT number 3 allows for a comment to be appended to the numeric value. For example, nuts per bolt. 53

0


54

0

Use the pipe support tag number as the index into the specialty material description library for pipe supports.

1

Use the pipe support commodity code, which must be upper cased, as the index into the specialty material description library for pipe supports.

7 - 30


55

0 1 2

Do not alter extraction criteria case Convert extraction criteria to Lower-case. Use upper-case extraction criteria. This option performs pipeline extractions where attribute data has been stored in a lower-case format in the database. All text generated in the resulting isometric drawings will still be upper-case. Note that when extracting by line ID, and code listed attributes are involved, that the code list set must be stored in lower-case.

56

0

Form the commodity code for chain operators using the operator type attribute.


57

1

Form the commodity code for chain operators using the chain operator number.

0

Do not generate labels consisting of segment node numbers.

1

Generate labels consisting of segment node numbers to assist flow sheet checking. However, if the node number is blank, labels will not be generated.

7 - 32


58

2

Always generate labels consisting of segment node numbers even when the node number is blank. An * is displayed if the node number is blank.

0

Append the bolt length to the material description for bolts.


59

1

Do not append the bolt length to the material description for bolts.

0 1

Display valve operator when it is not in a primary direction. Do not display valve operator when it is not in a primary direction. NOTE: This option is used in conjunction with ATEXT -213, spindle direction.

60

0

1

Search continuation areas defined in the Add Iso Area or Revise Iso Area forms for continuation items only. The database partitions of the models contained in the primary area (the area listed in the batch input file) are the only models scanned for the pipeline to be extracted as defined by the LINE_ID_DEFINITION section of the options file. The remaining models that are attached as references are scanned for continuation items, both pipeline and equipment nozzles. If the same pipeline, as defined by the LINE_ID_DEFINITION, continues into another area, a continuation note is displayed on the iso that points to the same line name as the iso being extracted. Search continuation areas for LINE_ID_DEFINITIONs and continuation items. Any items that match the line ID will be included in the output isometric. All of the models from all of the pipeline continuation areas defined in the Revise Iso Area form is scanned for the line to extract. Also, all of the reference models are scanned for continuation items (both pipeline and equipment nozzles). If the same pipeline, as defined by the LINE_ID_DEFINITION, continues into another area, and the area is listed in the Revise Iso Area form, the pipeline is included in the extraction. NOTE: When set to 1, option 60 increases iso extraction time. It is recommended that option 60 be set to 0 unless the line to be extracted extends across multiple areas.

2

Search all areas of the project for LINE_ID_DEFINITIONs and continuation items ignoring the continuation settings in the Revise Iso Area form. ISOGEN searches every piping model in the project for the pipeline to be extracted and also searches every equipment model for nozzle continuation items. NOTE:

7 - 34


Because there is no direct control over the number of models scanned by the software, setting 2 will take longer to process that setting 0 or 1. 61

0

Generic item names such as COMP, INST, and SUPP will be generated in the HITS file until the last section "Design file data in IDF order" is printed. This section will print four characters of the actual item name from the database.


Occ

PIPE

30

cp # 1

13.69

X

-28.50

Y

10.00

Z


0

0

Flags 5

Topo 0

Seq Branch Sg_occ 0

0

27

1

PIPE

30

2

15.69

-28.50

10.00

0

0

0

5

0

0

0

27

2

COMP

51

0

16.44

-28.50

10.00

0

0

0

3

0

0

0

27

3

COMP

51

1

15.69

-28.50

10.00

0

0

0

3

0

0

0

27

4

COMP

51

2

16.44

-29.25

10.00

0

0

0

3

0

0

0

27

5


Occ

PIPE

30

cp # 1

13.69

X

-28.50

Y

10.00

Z

Node Direct Section -1

1

0

Flags 5

Topo 0

Seq Branch Sg_occ 0

0

27

1

PIPE

30

2

15.69

-28.50

10.00

1

1

0

5

0

0

0

27

2

COMP

51

1

15.69

-28.50

10.00

1

1

0

3

0

0

0

27

3

COMP

51

2

16.44

-29.25

10.00

-1

2

0

3

0

0

0

27

4

COMP

51

0

16.44

-28.50

10.00

0

2

0

3

0

0

0

27

5


Cp

Name

Node

5 Next

Action

30

2

PIPE

1

2

1

1

1

5 Next

51

1

COMP

1

4

1

1

2

5 Next

51

2

COMP

-1

5

1

1

3

-1

1

Ref Design

0

# Sections =

1


Occ

COMP

51

cp # 0

16.44

X

-28.50

Y

10.00

Z


2

0

Flags 3

Topo 0

Seq Branch Sg_occ 0

0

27

1

PIPE

30

1

13.69

-28.50

10.00

-1

1

1

5

1

0

0

27

2

PIPE

30

2

15.69

-28.50

10.00

1

1

1

5

1

1

0

27

3

COMP

51

1

15.69

-28.50

10.00

1

1

1

3

1

2

0

27

4

COMP

51

2

16.44

-29.25

10.00

-1

2

1

3

1

3

0

27

5


X

Y

Z

X

Y

Z

Occ

PIPE

333756

-694944

243840

382524

-694944

243840

30

1

2

in

51

27

E90L

382524

-694944

243840

400812

-694944

243840

51

1

0

in

0

27

E90L

400812

-694944

243840

400812

-713232

243840

51

0

2

ou

0

27

61

1

in_cp Out_cp Leg Dn_occ Sg_occ

End

Item names from the database will be generated for all sections of the HITS file. Setting this option to a 1 will increase extraction time by approximately 25%. Intergraph recommends this option be used for debug purposes only.


Occ

PIPE

30

cp # 1

X 13.69

Y -28.50

Z 10.00


0

0

Flags 5

Topo 0

Seq Branch Sg_occ 0

0

27

1


PIPE

30

2

15.69

-28.50

10.00

0

0

0

5

0

0

0

27

2

E90L

51

0

16.44

-28.50

10.00

0

0

0

3

0

0

0

27

3

E90L

51

1

15.69

-28.50

10.00

0

0

0

3

0

0

0

27

4

E90L

51

2

16.44

-29.25

10.00

0

0

0

3

0

0

0

27

5


Occ

PIPE

30

cp # 1

13.69

X

-28.50

Y

10.00

Z

Node Direct Section -1

1

0

Flags 5

Topo 0

Seq Branch Sg_occ 0

0

27

1

PIPE

30

2

15.69

-28.50

10.00

1

1

0

5

0

0

0

27

2

E90L

51

1

15.69

-28.50

10.00

1

1

0

3

0

0

0

27

3

E90L

51

2

16.44

-29.25

10.00

-1

2

0

3

0

0

0

27

4

E90L

51

0

16.44

-28.50

10.00

0

2

0

3

0

0

0

27

5


Cp

Name

Node

5 Next

Action

30

2

PIPE

1

2

1

1

1

5 Next

51

1

E90L

1

4

1

1

2

5 Next

51

2

E90L

-1

5

1

1

3

-1

1

Ref Design

0

# Sections =

1


Occ

E90L

51

cp # 0

16.44

X

-28.50

Y

10.00

Z


2

0

Flags 3

Topo 0

Seq Branch Sg_occ 0

0

27

1

PIPE

30

1

13.69

-28.50

10.00

-1

1

1

5

1

0

0

27

2

PIPE

30

2

15.69

-28.50

10.00

1

1

1

5

1

1

0

27

3

E90L

51

1

15.69

-28.50

10.00

1

1

1

3

1

2

0

27

4

E90L

51

2

16.44

-29.25

10.00

-1

2

1

3

1

3

0

27

5


X

Y

Z

X

Y

Z

Occ

PIPE

333756

-694944

243840

382524

-694944

243840

30

1

2

in

51

27

E90L

382524

-694944

243840

400812

-694944

243840

51

1

0

in

0

27

E90L

400812

-694944

243840

400812

-713232

243840

51

0

2

ou

0

27

62

Position A

in_cp Out_cp Leg Dn_occ Sg_occ

End

Weld Number Display This Intergraph option has multiple switch settings (such as A, B, C, D). Intergraph switch settings are read from right to left (D-C-B-A). For example, if this option is set to 21, 1 represents switch position A and 2 represents switch position B. When setting an option with multiple switches, leading zeros may be omitted, but trailing zeros must be included.

0 1

Do not display PDS generated weld numbers. Display PDS generated weld numbers on Iso drawings.

Position B 0

Weld Number Display on the BOM Do not write weld numbers on isometric drawings. Instead, display the welds in the bill of material (BOM). Display weld numbers on isometric drawings and in the bill of material (BOM).

1

7 - 36


Position C 0

Weld Display at Sheet Breaks Place the weld at the sheet break on the sheet containing the component that has the higher east, north and elevation coordinate. Place the weld at the sheet break on both sheets. The weld is displayed as non-dashed on both isometrics.

1

NOTE: Intergraph option 62, position C, must be set to 1 for ISOGEN option 22 (Field Fit Length) to work properly. ISOGEN option 53, Weld Numbers, must be turned on in order to display the generated weld numbers on isometric. By default, this option generates a normal un-boxed arrowed message. If an enclosure is chosen using ISOGEN option 75,switch position A, only options 1, 2 and 5 should be used. Information on the Drawing and/or the parts list will be as follows: COMMODITY CODE (-20 record): ’SHOP’ or ’FIELD’ or ’OFFSHORE’ DESCRIPTION (-21 record): ’Weld Type, Material A, Material B’ For example: Part No. ____

Weld Description ___________

NPD (IN) ____

CMDTY Code _____

QTY _____

9

SHOP WELD, 5 IN OD, B166-600 (N06600) HOT FIN SHOP WELD, B166-600 (B0660) HOT FIN, 5 IN OD

4

SHOP

2

4

SHOP

2

10

63

0 1

Do not calculate the isometric center of gravity and the total isometric weight. Calculate the isometric center of gravity and total isometric weight. NOTE: A center of gravity weight library must be defined in the ninth entry under the FILES section of the Options file for option 63 to function properly. Refer to The Files Table, page 7 - 42 for more information.

64

0 1

Uses the standard MTO-Neutral file length of 256 bytes. Uses the expanded MTO-Neutral file length of 1024 bytes.


65

0

1 66

0 1

Dimensions on supports are determined by the ISOGEN option switches 8, 9 and 40 and the NON_DIMENSIONED_SUPPORTS section of the Intergraph options file. Disable dimensioning for all supports. Do not use the detail sketch facility. Use the detail sketch facility. When option 66 is set to 1, the section DETAIL_SKETCH_FACILITY must exist in the options file. The syntax of this section is similar to the TYPE_2_LABEL section. A note, referring you to the appropriate sketch, will be automatically generated and placed on the iso. NOTE: ISOGEN switch 71 must be set to 8000 for option 66 to function properly.

67

0 1 2

Do Not generate shop welds. Generate shop welds. Generate shop welds, but do not generate shop welds at pipeto-pipe connections.

68

0 1

Extract drawing even if original start point cannot be used. Stop extraction for a drawing if the original start point cannot be used. NOTE: This option is used in conjunction with ISOGEN’s repeatability function.

69

0 1

Do not produce the ISOGEN weld summary report. Produce the ISOGEN weld summary report.

70

0

Generate isometric limit points (sheet split record) in the intermediate data file (IDF) file as defined in PD_Design. Do not generate isometric limit points (sheet split record) in the intermediate data file (IDF).

1

71

Structural Column Reference

This option allows you to place reference dimensions from a structural column or grid line to one item on the isometric. WARNING: Before using option 71 you must have an up-to-date FrameWorks Reference Definition File that provides the location of all structural components and grid lines in the project. See Generate FrameWorks Reference Dimension File, page 5 - 86.

7 - 38


This option references structural elements according to their active cardinal point at the time of placement. It is highly recommended that structural columns be placed by CP5 (center-center) if it is anticipated that the Iso Structural Reference feature will be used. See Generate FrameWorks Reference Dimension File, page 5 - 86. NOTE: Since a single reference file is used for the entire project, no structural models can be excluded from being referenced. Hence, there is no selectivity as to what structural column or grid line will be referenced on the iso. The referenced structural element will always be the one nearest to the start of the pipeline being extracted. If a FAIL message appears on the isometric drawing and the .err file is reporting a (35:2012) DATA FAULT, DOUBLEBACK PIPE error, refer to ISOGEN message file errors section of this document for information on the nature of this error. This Intergraph option has multiple switch settings (such as A, B, C, D). Intergraph switch settings are read from right to left (D-C-B-A). For example, if this option is set to 21, 1 represents switch position A and 2 represents switch position B. When setting an option with multiple switches, leading zeros may be omitted, but trailing zeros must be included. Position A 0 1

Reference Dimension Control Do not place reference dimensions. Place structural reference dimension at the first component encountered from the start point.


2

Place structural reference dimension at the start point of the pipeline.

Position B 0 1

Reference Location Reference to the closest column. Reference to the closest horizontal and vertical grid lines ignoring elevation changes.

7 - 40


2

Reference to the closest horizontal and vertical grid lines and display elevation changes.

Position C 0

Skew Box Display References with skewed movements will not be displayed with a skewed box. References with skewed movements will be displayed with a skewed box.

1

Position D 0 1 2 3

Enclosure Type No enclosure for the reference. Use a rectangle for an enclosure. Use an arrow-ended rectangle for an enclosure. Use a round-ended rectangle for an enclosure.

Position E 0 1 2 3 4

Line Style Use the default line type. (short dash line) Use style 1 line type (long dash/short dash line) Use style 2 line type (dash/dot-dot line) Use style 3 line type (dotted line) Use style 4 line type (dash/dot-dot line)


72

Breaks on Flanged Pipe

This option controls whether flanged pipe will report as one peice or will break at pipe supports or olet branches.

0

Break flanged pipe into pieces when there is a pipe support or olet branch along the pipe. Report flanged pipe as one piece even when there is a pipe support or olet branch along the pipe.

1

NOTE: If this option is set to 1 and there are olet branches on the flanged pipe, the weldolets (WOL) are mapped to ISOGEN symbol key WTBW and represented with coupling record 126 in the Intermediate Data file (.idf file).

7 - 42


7.4 The Files Table __________________________________________________________________________________________________________________________________________________ The Files table contains the names of several external files which are used by the ISOGEN interface. The entries in this table are order dependent and must be in the order shown below. All files may be defined as: network address: /directory path/file name. For example: pdscert: /usr/isofiles/symbol.map 1.

The PDS to ISOGEN symbol map This table maps PDS component names to ISOGEN symbol names. The format and contents of the table are discussed in more detail in the section PDS-to-ISOGEN Symbol Map. This library is required and must be specified.

2.

The ISOGEN user-defined symbol library This is a library of ISOGEN symbols that has either been translated from the VAX (see the README file for translation information) or has been added to those delivered with the ISOGEN product. This library is optional and need not be specified.

3.

The label description library This is a library of user-defined labels which are based on database attributes. Creation of library entries is discussed in the PDS Reference Data Manager document. This file specification is redundant in that a label description library is already referenced by piping model files. However, if you specify it here, you can have a separate library that is used specifically for iso extraction and for no other purpose. If this entry is left blank then the library referenced by the piping model file is used instead.

4.

The valve / valve operator symbol map (VALOPR table) This file contains a table that can be used to map a PDS valve and valve operator combination to a different symbol than that mapped by valve alone. This table is discussed in the section The Valve/Operator Table.


In order to use this file, Intergraph options block option 31 must be set to 1.

This is an optional file name.

5.

The mto neutral file map This file contains the tables which govern the format of the Intergraph mto neutral file. Refer to The MTO Neutral File Record Map, page 12 - 1 for more information. In order to use this table, Intergraph options block option 20 must be set to 1.

6.

Reserved

7.

The Title Block Tables File This is an optional file containing tables that govern the generation of text that is to be inserted into a drawing title block by the batch extraction software. When you specify this table, you must also enable option 34 in the Intergraph options block.

8.

The Notes Table This file is optional and contains data that can be mapped to the title block by the batch extraction software. The table is accessed through the Title Block Tables File. The Notes Table allows you to map data to the title block which is not stored in the database.

9.

Center of Gravity Weight Library This is an optional library that generates center of gravity calculations for ISOGEN. For more information on center of gravity calculations, see Center of Gravity Calculation, page 19 - 2 . In order to use this library, Intergraph options block option 63 must be set to 1.

10.

Detail Sketch Facility Cell Library This is a cell library which contains the cells specified in the DETAIL_SKETCH_FACILITY section of the options file.

7 - 44

11.


Drawing Definition File This file allows you to customize line weight, size and output level of the data on the isometric drawing.

12.

Welds Definition / Format File This file specifies the format of the weld box that will be appear on the isometric drawing. It is also used to define the weld report.

13.

Material List Definition File This file allows you to define the format of a STYLE 2 or STYLE 3 Material Take Off.

14.

Basic Bending Parameters File This file can be used as a basic set of input to a bending machine. The 14th entry in the FILES section of the options file will contain the name of this file. If the first character of the entry is *, the generated file will be isoname.bnd; where isoname is the name used in creating the isometric design file name. If this entry contains a node, directory and filename, the bending information is appended to that filename for each extracted line. If this entry is left blank, a bending parameters file will not be generated.


7.5 USER_DEFINED_WELDS __________________________________________________________________________________________________________________________________________________ This table allows you to to assign a weld symbol to a particular weld type. ISOGEN, versions 5.0 or later, allow you to create a user-defined weld symbol by using the symbol definition software. Once created, the new weld symbol graphics should be proportionate to other user-defined symbols. The newly created symbol should be mapped to a specific weld type in the USER_DEFINED_WELDS section of the options file. Note that the weld symbol is not mapped in the isomap.tbl file. By using the following table format, you can define which SKEY is used with each weld type. For example, if a weld type codelist number is defined to use the SKEY FFWT, ISOGEN generates the appropriate text and adds extra material as defined in the ISOGEN section of the options file. The format of a table entry is: VTF, VAL1, VAL2, ...,VALn, WELDTYPE, SYM

Where: VTF

is a number indicating the number of values to follow (maximum of 20 values per line.

VAL1-VALn

are the weld type attribute values that will be mapped to the symbol defined (SYM).

WELDTYPE

is a number 1-3 where: 1: SHOP 2: FIELD 3: OFFSHORE

SYM

is the ISOGEN weld symbol name.

7 - 46


If the table is not defined or a weld type code list value is not included in the table, the following action is taken: For more information, see Weld Types and Mapping, page 16 - 3 .

codelist value (from codelist 1100, Weld Type) 1 = No weld 11-20 = ’WW’ (shop weld) else = ’WF’ (field fit weld)

Example 1: Generating a user-defined weld from codelist values Show the required entries to generate the following welds: a site weld symbol when codelist value 22 is used. This is a field weld, but does not require extra material to be added. an offshore field fit weld symbol for code list values 30-33 inclusive. a mitre offshore weld symbol for codelist value 40. The format of the table entry is:

USER_DEFINED_WELDS 3 1, 22, 2, ’WS’ 4, 30, 31, 32, 33, 3, ’WOF’ 1, 40, 3, ’WM’


7.6 WELD_PREFIX __________________________________________________________________________________________________________________________________________________ This table is used to add a prefix to an isometric weld number that is contained within an enclosure. The WELD_PREFIX table also allows the prefix to be positioned on the drawing frame as a form of general note about weld identification. The weld prefix may also be included as part of the output in the user-defined weld summary report. The format of a table entry is:

WELD_PREFIX 1 #, ’TEXT’

Where: #

is a number 0 through 3 where: 0 - is a general weld prefix to apply to all weld types 1 - is a shop weld prefix to apply only to fabrication welds 2 - is a site/field weld prefix to apply only to erection welds 3 - offshore weld prefix to apply only to offshore welds

’TEXT’

is the actual prefix to be used If all four prefixes are defined, the general weld prefix (setting 0) will be ignored.

Example 1: Defining a Weld Prefix Determine the table entry that would have all offshore welds have the prefix ’OFFSHORE-’ on the iso drawing. The table entry would be:

WELD_PREFIX 1 3, ’OFFSHORE-’

7 - 48


7.7 DETAIL_SKETCH_FACILITY __________________________________________________________________________________________________________________________________________________ This table is used to generate a detailed sketch or information note for specific item. Any component meeting the specified value defined in this table generates a defined detail sketch or note. The defined value must exactly match the attribute or label. You can generate general or specific notes for components and spools. The general information note places a note on each isometric sheet of the pipeline. The specific information note only places a note on the specific isometric sheet that contains the item generating the note. You can define up to 300 Detail Sketch Facility table entries.

The format of a table entry is:

TABLE, COL, LABEL, ’COL VAL’, ’DET NAME’

Where: TABLE, COL

is the table, column specification of the attribute that will be checked and compared with ’COL VAL’.

LABEL

is the label description library number that defines the format of the note that will be checked and compared with ’COL VAL’. When using LABEL, TABLE must be set and COL must be 0.

’COL VAL’

is the value that when equal to TABLE,COL or TABLE,LABEL will trigger the detail to be placed on the isometric.

’DET NAME’

is the name of the detail cell from the cell library (defined by the tenth entry under the files section of the options file) to place on the isometric.

Information Note Entries Two types of information notes are available: General Notes are indictaed by a _N at the end of the cell. Specific Notes are indictaed by a _S at the end of the cell.


All cell names that end with _N or _S are treated as Information Notes and placed accordingly. ATEXT numbers -541 and -542 also effect these criteria. -541 _N is used as the delimiter/identifier in the general note name. -542 _S is used at the delimiter/identifier in the specific note name. Example 1: Example of the DETAIL_SKETCH_FACILITY Table

DETAIL_SKETCH_FACILITY 5 34, 0, 900, ’6Q1C01 GAT’, ’det_4’ 34, 3, 0, ’6Q3C74’, ’det_1’ 34, 20, 0, ’90.0000’, ’det_2’ 34, 0, 924, ’H’, ’HOLD_N’ 12, 12, 0, ’SYS1’, ’I5_S’

!5 entries to follow !label 900: piping_comp_no, commodity_name !commodity_name, character(6) !bend_angle, double !Comp HOLD status note !Specific Note Package #

7 - 50


7.8 PIPELINE_HEADER __________________________________________________________________________________________________________________________________________________ The pipeline header table is used to generate records in the intermediate data file that cause attribute change graphics to be generated in the isometric drawing. Attribute change graphics can be used at changes in piping materials class, insulation type, and so on, along a pipeline. This table allows you to control the database attributes that are used to generate attribute breaks on the drawing.

Example attribute change graphics This table is also used to generate a note when some database attribute of a component overrides that of the pipeline. For example, a new pipeline might contain an existing valve. This table can be used to generate a note on the drawing that points to the valve and identifies it as existing. The format of a row (or a single entry) in this table is:

RECNO, ST, SC, SN, DFLT, PREFIX, CT, CC, CN, PT, PC, PN, IT, IC, IN

Where: RECNO

is the ISOGEN record number used for an attribute whose value can change along the length of a pipeline. Record numbers from the following table must be used for this item:


Table 7 - 1. ISOGEN record numbers for pipeline attributes ISOGEN No _Rec ______

Attribute _________

ATEXT No _____

-6 -7 -11 -14 -15 -16 -17 -41 -42 -43 -44 -45

Line name Spool number prefix Piping materials class (spec) Date Record Insulation type Heat tracing type Paint code User-defined 1 User-defined 2 User-defined 3 User-defined 4 User-defined 5

-288 n/a -289 -250 -290 -291 -292 -293 -294 -295 -296 -297

An entry in the PIPELINE_HEADER table with an ISOGEN record number of -7 is used to define a spool number prefix. If defined, the prefix is used by ISOGEN to form spool number labels in the drawing. When defining spool number prefixes, use a single ? symbol to generate spool numbers only. Use two ? symbols for the spool number prefix to generate spool numbers and sheet numbers. As shown in the previous figure, the actual attribute values at an attribute change are preceded by some clarifying text. That text is "MATL," which identifies that the attributes shown are piping materials classes. For information on modifying this text, refer to ATEXT_SPECIFICATIONS, page 7 - 56 . The Atext numbers you will need in the ATEXT_SPECIFICATIONS table to change the clarifying text are shown above in Table 7-1. In the case of the user-defined attribute changes the default Atexts are blank. In order to generate attribute change graphics in the drawing you MUST define nonblank Atexts that correspond to the ISOGEN record numbers you use. For example, if you want to use ISOGEN record number -41 for a user-defined attribute change then you must define ATEXT number -293 with a nonblank value if you want to see the attribute change on the drawing. The Atext numbers shown in Table 7-1 modify only the clarifying text shown with the attributes in the drawing. They do not modify the title block entries for these attributes. Different Atext numbers are used to modify this text. Refer to Appendix B for details.

7 - 52


ST, SC

is a table, column specification for the segment attribute whose value might change along the pipeline. This attribute specification can be any segment level attribute in the material database. The segment level table is table 12. The specification for piping materials class, for example, would be table 12, column 12.

SN

is an optional label description library number that you can use to specify the segment attribute(s) that might change. By using the label description library number rather than than ST, SC (above) you can define composite attributes that are combinations of 2 or more database attributes. The label description library holds a definition of each label description library number. The number and its description in the label library can be used to form a text string (a label) that is formed from database columns. You define which columns are used in the label as well as the label format when making a definition in the label library. Iso extraction treats a string based on a label library number as a pseudo attribute. A pseudo attribute can be used to generate attribute breaks just the same as regular database attribute can.

DFLT

is an optional string used to define a default value for an attribute or label. When the attribute defined by ST,SC or SN is undefined (blank) then DFLT will be used. This shows attribute breaks for attributes that you normally do not want to provide values for. If you do not provide a value for this field the string "UNDEFINED" is used for undefined attributes.

PREFIX

is an optional prefix used in forming a note from a database attribute when a component attribute overrides a segment attribute. The override note is formed by appending the database attribute to the prefix defined here. The note formed in this manner points to the appropriate component in the drawing. When the ISOGEN record number for the spool prefix is -7, PREFIX is used as a separator between the spool prefix and the spool number.

CT, CC

is the table, column specification for the component level attribute that can override the pipeline level attribute defined by ST, SC. These items are optional. Some pipeline level attributes cannot be overridden at the component level (pipeline name and piping materials class are examples). When there is no override attribute these items should be set to 0. Attribute specifications for CT, CC apply to the component table (34) in the design database.


CN

is the component level counterpart to SN. If the label generated by CN differs from that generated by SN then an override note will be generated. In order to avoid generating override notes on every component you must either define CN in exactly the same way as SN except for the table and attribute numbers or not use the component override feature.

PT, PC

is the same as CT, CC except that this attribute specification applies to pipe rather than components. Attribute specifications can only refer to table 50 in the design database.

PN IT, IC

is the same as CN except that it applies to pipe. is the same as CT, CC except that this attribute specification applies to instruments rather than components. Attribute specifications are from the instrument table (67).

IN

is the same as CN except that it applies to instruments.

Example 1: Breaking Supply Responsibility Along a Pipeline Since there is no predefined ISOGEN record number for supply responsibility, you must use one of the user-defined records. Record -41 is used in this example. Referring to the database table format, the following database attributes apply:

Segment Component Pipe Instrument

12, 39 - does not apply - does not apply - does not apply -

The table entry would appear as follows:

-41, 12, 39, 0, ’’, ’SUPPLIED BY’, 0, 0, 0, 0, 0, 0, 0, 0, 0

Example 2: Changing Construction Responsibility Along a Pipeline As in the previous example, there is no predefined ISOGEN record number for construction responsibility. So, you must use one of the user-defined record numbers. Record -42 is used in this example. The applicable database attributes are:

Segment Component Pipe Instrument

12, 38 - does not apply - does not apply 67, 29

The appropriate table entry would be:

7 - 54


-42, 12, 38, 0, ’’, ’CONSTR BY’, 0, 0, 0, 0, 0, 0, 67, 29, 0

Example 3: Breaking Composite Attributes by Combining Insulation Purpose and Thickness For this example, we can use ISOGEN record number -15. Since the change that will be shown is made up of multiple attribute changes, we must use the label description library to form a pseudo attribute. Using the label library utility we have defined the following library numbers: 956 - segment insulation purpose and thickness 957 - instrument insulation purpose and thickness The table entry for this case would be:

-15, 0, 0, 956, ’’, ’’, 0, 0, 0, 0, 0, 0, 0, 0, 957

The first entry in the PIPELINE_HEADER table MUST be for line name (using the -6 record). Otherwise, the ISOGEN interface will stop with an error. The attribute that is used for this entry is displayed in the pipeline ID box in the lower right hand corner of the drawing. You can use either the line name attribute (table 12, attribute 2) or the line ID (specified by using table 12, attribute -2) for ST, SC. Refer to LINE_ID_DEFINITION, page 7 - 59 for information on how a line ID differs from a line name.

The table entries should be in order of increasing absolute value of ISOGEN record number.

Attribute changes in the drawing can be inhibited by either removing the entry for the attribute from this table or by setting the Atext for the clarifying text to blank in the ATEXT_SPECIFICATIONS table.

When attributes are specified, the label library number should be 0. When the label library number is specified then the attribute specifications should be 0.

The line ID (COL = -2) can be used for the spool prefix.

ISOGEN word 39 must be set to 0 in order to display spool number labels formed using the spool prefix.


If ST is less than 0, the attribute is checked for component overrides but no segment level breaks will be shown in the drawing. When ST is made negative, set RECNO to an undefined record number (such as -99).

7 - 56


7.9 ATEXT_SPECIFICATIONS __________________________________________________________________________________________________________________________________________________ This table is used to modify the values of text strings that ISOGEN puts on drawings. A table entry can also "turn off" a text string so that it does not appear. The format of a table entry is:

ATEXT number, ’new text’

Where: ATEXT number

is one of the ATEXT numbers defined in Appendix B of the ISOGEN Facilities Guide (which is Appendix B of this document).

’new text’

is the new text string to be applied to the Atext number. The ’new text’ will be used instead of the text defined in Appendix B of the facilities guide.

A particular text string can be turned off by setting its Atext value to blank. Example 1: Modifying Text Modify the clarifying text that precedes a piping materials class that is generated at a spec change by changing "SPEC" to "MATL". The table entry would be:

-289, ’MATL’

Example 2: Modifying Text for an Eccentric Reducer Turn on the "FLAT SIDE DOWN" message that points to eccentric reducers (this message is off by default). Refer to Appendix B for further explanation. The table entry would be:

-243, ’FLAT SIDE DOWN’

The table entries must be in order of increasing absolute value of Atext number. That is, -206 should precede -207 and so on. If one specification is out of order then all of the following entries will be ignored.


In order to turn off all ISOGEN generated title block data the following Atext specifications can be used: -250, ’ ’ -253, ’ ’ -270, ’ ’ -271, ’ ’ -272, ’ ’ -317, ’ ’ -318, ’ ’ -400, ’ ’ -401, ’ ’ -402, ’ ’ -403, ’ ’ -404, ’ ’ -405, ’ ’ -406, ’ ’ -407, ’ ’ -410, ’ ’ -411, ’ ’

7 - 58


7.10 INGR_ATEXT_SPECIFICATIONS __________________________________________________________________________________________________________________________________________________ This table is used to modify the values of text strings that PD_ISO puts on drawings. The format of a table entry is:

ATEXT number, ’old text’, ’new text’

Where: ATEXT number is 1-15 1: ’NOT FOUND’ 2: ’BOLT LENGTH’ ’old text’

is the text string to be substituted.

’new text’

is the new text string to be applied to the Atext number. The ’old text’ value is used if the ’new text’ value is left blank or if the INGR_ATEXT_SPECIFICATIONS records are omitted from the Options file.

INGR_ATEXT_SPECIFICATIONS include: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16,

’NOT FOUND’, ’BOLT LENGTH’, ’NUTS PER BOLT’, ’CHAIN_’, ’FSTAND_’, ’XSTEM_’, ’HOR’, ’VOR’, ’DEG’, ’E’, ’N’, ’U’, ’W’, ’S’, ’D’, ’****’

’’ ’’ ’’

!Used based on Intergraph option 6 and ATEXT -209 !Used based on Intergraph option 58 !Used based on Intergraph option 52

’’ ’’ ’’ ’’ ’’ ’’ ’’ ’’ ’’ ’’ ’’ ’’ ’’

!Used based on Intergraph option 33,56 !Used based on Intergraph option 33 !Used based on Intergraph option 33 !Horizontal - Used for an operator in a 2plane ske !Vertical - Used for an operator in a 2plane ske !Degree - Used for an operator in a 2plane ske !Used with skewed operator orientation notes !Used with skewed operator orientation notes !Used with skewed operator orientation notes !Used with skewed operator orientation notes !Used with skewed operator orientation notes !Used with skewed operator orientation notes !Default text used for unassigned inspection numbers


7.11 LINE_ID_DEFINITION __________________________________________________________________________________________________________________________________________________ This table is used to define the format of the line ID. The line ID is a composite attribute that should be formed from a subset of those attributes which are used to form the line name attribute. The line ID is intended to be a simpler way of referring to a pipeline. The format of a table entry is:

ST, SC, ’SUFFX’

Where: ST, SC

is the table, column specification for one of the attributes making up the line ID. Any attribute from the segment level (table 12) can be used.

’SUFFX’

is an optional, single character, suffix used to terminate the attribute in the line ID. A null entry (two successive single quotes) is valid.

The line ID itself is formed by linking all the attributes together with their suffixes if defined. The result is the line ID label. In order to use the Display Iso feature from an interactive piping session, this table and column must be set to 12, 3 Example 1: Defining a Line ID Define a line ID composed of fluid code, sequence number and unit code. The column numbers involved are: Fluid code Sequence no Unit no

12, 9 12, 10 12, 4

The table is defined as: 12, 9, ’-’ 12, 10, ’’ 12, 4, ’’ Using the previous line ID, what is the line ID for a line named 16IN-P12002-1C003? Assuming that a single digit unit number follows sequence number in this line number, the line ID would be P-12002. The suffix character defined in the table is used only in generating the text string for display purposes. When inputting line names for extraction every attribute forming the line ID MUST be separated by dashes. For instance, to input the line ID in Example 8 you must key in P-1200-2.

7 - 60


7.12 TYPE_1_LABELS __________________________________________________________________________________________________________________________________________________ This table is used to generate notes on drawings that point to specific components. This table causes a note to be generated when some database attribute which you define in the table has a value. When the attribute is undefined (that is, does NOT have a value) then no note is generated. When a line is extracted, each component is processed one at a time. This table allows you to generate a note, based on the value of a component’s attribute, at the time it is being processed. You can define up to 50 table entry lines for Type 1 Labels.


COMP TYPE, TABLE, COL, LDL NO, ENC TYPE (optional)

Where: COMP TYPE

is the component type to which the note should apply. Allowable values for component type are: 1 - Commodity item 2 - Specialty item 3 - Pipe 4 - Instrument 5 - Pipe support

TABLE, COL

is the table, column specification for the attribute that should be checked. If this attribute is defined, the note will be generated. An attribute is considered undefined based on its data type as follows: Integer - set to 0 Real - equal to -32768 ASCII - blank or null Coded - 0 or 1 Any attribute that is not undefined is defined and will cause a note to be generated. You can also specify that a Real attribute be considered undefined if it contains the value 0.0. To do this, make the value of TABLE negative in the table (such as use -34 instead of 34 to designate table 34).


LDL NO

is the label description library label number that defines the format of the note that is to appear on the drawing. You must define this note in the label description library as defined in the PDS Reference Data Manager document. If the label references attributes from the database, the attributes must be from the table defined by TABLE or its associated table.

ENC TYPE

is the enclosure type. There are five text-type records that trigger the different enclosures shown below. If an enclosure is not required, use 0 as the enclosure type. Type 1 Enclosure This enclosure type can handle an unlimited number of characters on a single line. Type 2 Enclosure This enclosure type can handle an unlimited number of characters on a single line. Type 3 Enclosure This enclosure type can handle an unlimited number of characters on a single line. Type 4 Enclosure This enclosure type can handle a maximum of three characters on a single line. Type 5 Enclosure This enclosure type can handle a maximum of three characters on a single line.

Example 1: Defining Type 1 Labels Define a table entry that would generate a note (without an enclosure) when the REMARKS field attribute for the component is defined. Using the label library utility, we have defined label 910 as shown below:

7 - 62


The attribute referred to is table 34, column 46. The table entry would be: 1, 34, 46, 910 Where: 910 is the label number which defines the exact format of the note to be generated. The note would point to the item (or items) in the drawing that corresponds to the component(s) in the model whose remarks attribute has been defined. The database table defined by TABLE must correspond to the component type identified by COMP TYP. Thus, the following restrictions exist: COMP TYP ___________

Allowable values of TABLE __________________________

1 2 3 4 5

12, 34 12, 34 12, 50 12, 67 12, 80

When LDL NO is set to 0 in the table, no note is generated. The note that is defined by LDL NO need not use the attribute that is defined in the table as TABLE, COL. TABLE, COL is only the trigger in the note generation process. A dollar sign ("$") embedded in a label is treated as a line feed by ISOGEN.


7.13 TYPE_2_LABELS __________________________________________________________________________________________________________________________________________________ This table is used to generate notes that point to specific components. Use this table to generate a note whenever a specific attribute (user-defined in the table) is defined with a specific value (also defined by you in the table). Notice the difference between this table and the TYPE_1_LABELS table. Note that generation from the TYPE_1_LABELS table is triggered by an attribute having ANY value. This table is more selective in that you specify the value of the attribute that is to trigger note generation. You can define up to 99 table entry lines for Type 2 Labels.


TABLE, COL, ’COL VAL’, LENGTH, LDL NO, ENC TYPE (optional)

Where: TABLE, COL

is the table, column specification of the attribute that will be checked and compared with ’COL VAL’.

’COL VAL’

is the value of TABLE, COL that will trigger note generation. If ’COL VAL’ is the same as the value of TABLE, COL then a note will be generated that points to the item.

LENGTH

is an optional specification of the number of characters from the database attribute that should be compared with ’COL VAL’. If set to 0, all characters of the attribute will be compared with ’COL VAL’.

LDL NO

is the label description library number that defines the format of the note that will be generated when the attribute identified by TABLE, COL has the value ’COL VAL’ or the first 1 through LENGTH characters of the attribute are the same as ’COL VAL’. If the label references attributes from the database, the attributes must be from the table defined by TABLE or its associated table.

ENC TYPE

is the enclosure type. There are five text-type records that trigger the different enclosures shown below. If an enclosure is not required, use 0 as the enclosure type.

7 - 64


Type 1 Enclosure This enclosure type can handle an unlimited number of characters on a single line. Type 2 Enclosure This enclosure type can handle an unlimited number of characters on a single line. Type 3 Enclosure This enclosure type can handle an unlimited number of characters on a single line. Type 4 Enclosure This enclosure type can handle a maximum of three characters on a single line. Type 5 Enclosure This enclosure type can handle a maximum of three characters on a single line. Example 1: Defining Type 2 Labels Define a table entry that would generate a note (with a type 3 enclosure) that points to all blind flanges. One way to accomplish this would be to check the value of the PDS commodity_name attribute for the string "6Q2C08", the PDS commodity name for a Blind Flange. The appropriate attribute is table 34, column 3. The table entry would be: 3, 3, ’6Q2C08’, 0, 911, 3 Where 911 is the label description library label number which defines the format of the note. Label 911 is defined as follows:


Refer to notes 2, 3, 4, and 5 under the description of the TYPE_1_LABELS table. These notes also apply to the TYPE_2_LABELS table. To test on code list number values rather than code list text, set LENGTH to 0 and set COLVAL to the code list number. For example, to generate a note when the fabrication category 50(table), 14(col) is 25 use: 50, 14, ’25’, 0, 986.

7 - 66


7.14 TYPE_3_LABELS __________________________________________________________________________________________________________________________________________________ This table is used to generate a note when the value of a code-listed attribute matches one of the values specified in the table entry. This table is similar to TYPE_2_LABELS except that, rather than being triggered by a single value, a note can be triggered by one of several values. You can define up to 50 table entry lines for Type 3 labels.

The format of a table entry is as follows:

TYPE, TABLE, COL, LDL NO, NVALS, VAL1, VAL2, ... VALN, ENC TYPE (optional)

Where: TYPE

is the component type that the note should apply to. Use the following values for TYPE: 1- Commodity item 2- Specialty item 3- Pipe 4- Instrument 5- Pipe Support

TABLE,COL

defines the attribute that triggers note generation.

TABLE

must correspond to TYPE as follows: TYPE ______

ALLOWABLE TABLES _ _____________________

1 2 3 4 5

12, 34 12, 34 12, 50 12, 67 12, 80

LDL NO

Defines the format of the note to be generated if triggered. If the label references attributes from the database, the attributes must be from the table defined by TABLE or its associated table. If LDL NO is set to 0, the value of TABLE,COL is generated as the note.

NVALS

Defines the number of code list numbers in the list to follow.

VAL1...VALN

Code list numbers that should trigger note generation.


Example 1: Defining Type 3 Labels Show the table entry needed to generate a note when the component fabrication category is set to code list values 5, 7, or 17. The table entry would be:

1, 34, 10, 994, 3, 5, 7, 17

Where: Label 994 would define the format of the note that would be generated.

When LDL NO is set to 0 so that the code listed text is generated as the drawing note, the short form of the code list text (that to the left of the "=" in the code list source) can be generated by making COL negative. Therefore, in the previous example, the following would be used to generate the short form of the code list text as the note. 1, 34, -10, 0, 3, 5, 7, 17

7 - 68


7.15 START_POINT_NOTES __________________________________________________________________________________________________________________________________________________ This table is used to generate notes at the beginning of a pipeline. The format of a table entry is as follows:

TYPE, TABLE, LDL NO, ENC TYPE (optional)

Where: TYPE TABLE

Currently, TYPE must be set to 0. TABLE defines the tables that will be referenced by LDL NO as follows:

TABLE _______

Valid tables in label LDL NO _ __________________________

12 34 50 67

SEGMENTS COMPONENTS PIPE INSTRUMENT

LDL NO

Label library number which defines the format of a note to be generated on the first component of the pipeline.

ENC TYPE

is the enclosure type. There are five text-type records that trigger the different enclosures shown below. If an enclosure is not required, use 0 as the enclosure type.


Type 1 Enclosure This enclosure type can handle an unlimited number of characters on a single line. Type 2 Enclosure This enclosure type can handle an unlimited number of characters on a single line. Type 3 Enclosure This enclosure type can handle an unlimited number of characters on a single line. Type 4 Enclosure This enclosure type can handle a maximum of three characters on a single line. Type 5 Enclosure This enclosure type can handle a maximum of three characters on a single line. Example 1: Defining Start Point Notes Define a table entry that would generate the line name attribute at the start of a pipeline. The table entry would be:

0, 12, 900, 0

Where: Label 900 returns the line name (T12C2) followed by a dash and the text, "Starts Here".

7 - 70


7.16 END_POINT_COMPONENT_LABELS __________________________________________________________________________________________________________________________________________________ This table is used to define the format of notes that are generated at line endpoints when the line endpoint connects on to another pipeline. The note defined by this table is NOT generated at line endpoints that are not connected to other pipelines. The note itself is formed from the attributes of the connecting component. Each entry in the table is used to form one line of the note. Multiline notes are shown as a block of text on the drawing. The format of a table entry is:

’PREFIX’, CT, CC, CN, PT, PC, PN, IT, IC, IN

The attribute that is used for this entry is displayed in the pipeline ID box in the lower right hand corner of the drawing. You can use either the line name attribute (table 12, column 2) or the line ID (specified by using table 12, attribute -2) for ST, SC. Refer to LINE_ID_DEFINITION, page 7 - 59 for information on how a line ID differs from a line name. Where: ’PREFIX’

is a short prefix for the attribute that will be displayed at the line endpoint.

CT, CC

is the table, column specification of the attribute that will be displayed when the connecting component is a commodity item or a specialty item.

CN

is a label description library number that defines the format of the note line when the connecting component is a commodity item or a specialty item. When CN is used then CT should be set to a value that defines the tables referred to in the note description, held in the label library. That is, if the note definition uses table 12 then CT should be set to 12. If the note definition uses table 34, then CT should be set to 34. In generating a line in the line endpoint note either column CT, CC is appended to PREFIX or the line is generated using the label description library note identified by CN. When CT, CC is defined then CN should be 0. When CN is not 0 then CC should be set to zero.

PT, PC

is the table, column specification of the attribute that will be displayed when the connecting item is a pipe. These entries are analogous to CT, CC for components.


PN

is the label description library number that defines the format of the note line when the connecting component is a pipe. PN is analogous to CN for components. When using PN you must set PT to a value that reflects the tables used in the note definition. For example, if the note uses table 12 then PT must be set to 12. If it uses table 50 then PT must be set to 50.

IT, IC

is the table, column specification of the attribute that will be displayed when the connecting item is an instrument. These entries are analogous to CT, CC for components.

IN

is the label description library number that defines the format of the note line when the connecting component is an instrument. IN is analogous to CN for components. When using IN you must set IT to a value that reflects the table used in the note definition. For example, if the note uses table 12 then IE must be set to 12. If it uses table 67 then IE must be set to 67.

Example 1: Defining Continuation Notes Define the table entries that would generate a continuation note that consists of one line for the connected line’s line name. For the note, the applicable database attribute is table 12, column 2. The table entry would be:

’LINE:’, 12, 2, 0, 12, 2, 0, 12, 2, 0

Example 2: Defining Continuation Notes Redo example 1 using label description library numbers rather than column numbers. The table entry for the line name would be:

’’, 12, 0, 951, 12, 0, 951, 12, 0, 951

The label description library number option is useful when you want to display more than one attribute on a single line in the note. CT, PT, and IE are restricted as follows: CT- 12 or 34 PT- 12 or 50 IT- 12 or 67

7 - 72


7.17 NOZZLE_NOTE __________________________________________________________________________________________________________________________________________________ This table is very similar to the END_POINT_COMPONENT_LABELS table except that it is used to form a note when the line endpoint is connected to an equipment nozzle. The primary difference is that with the NOZZLE_NOTE table some lines in the connection note can be generated based on the generic termination type of the nozzle. The format of a table entry is:

GEN TYP, TABLE, LDL NO

Where: GEN TYP

is a number that indicates those generic termination types for which this note line should be generated. The allowable values of GEN TYP are: -1- to indicate that the note line should be generated for ALL generic termination types. 1- to indicate that the note line should only be generated when the generic termination type of the nozzle is FLANGED. 2- to indicate that the note line should only be generated when the generic termination type of the nozzle is FEMALE. 3- to indicate that the note line should only be generated when the generic termination type of the nozzle is MALE.

TABLE

is the database table from which attributes are taken in defining the label description library entry that is identified by LDL NO. If the attributes defined in the note are from the equipment table then TABLE should be 21. If the attributes used in defining the note are from the nozzle table then TABLE should be 22.

LDL NO

is the label description library number that defines the format of the note.

Example 1: Defining a Nozzle Connection Note Define a table that generates a nozzle connection consisting of the following lines: Line 1 Line 2 Line 3

Equipment item name Nozzle tag number A line that depends on end prep as follows: A) Flanged - size-rating-facing B) Socket weld - size-rating-facing C) Welded - size-schedule-end prep


The appropriate database attributes are:

Equipment name - table 21, column 2 Nozzle tag table 22, column 2 size table 22, column 4 rating table 22, column 5 end prep table 22, column 6 schedule table 22, column 17

The table would be:

-1, -1, 1, 2, 3,

21, 22, 22, 22, 22,

952 953 954 954 950

A note formed by this table for a flanged nozzle might be: ITEM: 2103-C NOZ: N11 6"-CL150-RFFE

If TABLE < 0 (such as -21 or -22) then the line will be appended to the previous line in the table without a linefeed. This allows you to combine attributes from tables 21 and 22 onto a single line in the note block. The Intergraph Options_Block word 23 controls whether the software uses the ISOGEN default nozzle note or the note defined by this keyword.

7 - 74


7.18 SECONDARY_ORIENTATION_NOTE __________________________________________________________________________________________________________________________________________________ This table is used to define valve operators that require a secondary orientation in order to install them. For each operator it also defines the prefix for the secondary orientation label. A table entry is as follows:

’OPER_NAME’, ’NOTE_PRFX’

Where: OPTR_NAME

is the symbol name of the valve operator which requires a second orientation.

NOTE_PRFX

is the prefix that should be used for second orientation.

Example 1: Defining Secondary Orientation Notes Define the table entry that would result in a secondary orientation note for the valve operator OP_9. The table entry would be: ’OP_9’, ’ORIENT WRENCH’ The above table entry creates the following note in a drawing:

The Intergraph Options_Block word 48 controls whether the software uses the ISOGEN default secondary orientation note or the note defined by this keyword.


7.19 DOTTED_SYMBOLOGY_CODE_LIST_VALUES __________________________________________________________________________________________________________________________________________________ This table is used to allow the values of certain database attributes to determine whether or not the piping in the isometric should be shown in dotted symbology or not. By using this table you can, for example, make all "existing" piping show up in the iso in dotted symbology rather than with solid lines. Only code-listed attributes can be used to determine whether or not a section of piping or a component is to be dotted. Code-listed attributes are displayed as text strings when the Piping Review Attributes command is used. Attributes are displayed as having an integer data type in the database table format. The format of an entry in this table is:

ST, SC, CT, CC, PT, PC, IT, IC, VTF, VAL1, VAL2, ... VALn

Where: ST, SC

defines a segment level column (from table 12) whose value might cause the piping to be dotted.

CT, CC

defines a component level column (from table 34) whose value might cause a commodity item or specialty item to be dotted.

PT, PC

defines a pipe column (from table 50) whose value might cause a piece of pipe to be dotted.

IT, IC

defines an instrument column (from table 67) whose value might cause an instrument to be dotted.

VTF

is the number of values to follow in the list VAL1 through VALn.

VAL1-VALn

are the values of the code-listed column which will force the symbology to be dotted.

Example 1: Defining Dotted Symbology Determine the table entry that will result in dotted symbology on the isometric when the construction status is "existing". The relevant database attributes are:

segment: component: pipe: instrument:

table table table table

12, 34, 50, 67,

column column column column

20 32 27 29

7 - 76


Looking at the code-list number 130 (the construction status code-list) we can find that the code-list number for "existing" is 3. Thus, the table entry would be:

12, 20, 34, 32, 50, 27, 67, 29, 1, 3

Whenever the value of the segment level attribute matches one of those in the list VAL1 through VALn, all of the components attached to the segment will be drawn with dotted symbology in the isometric. When the value of a component level attribute (defined by CT,CC, PT,PC, or IT,IC) matches a value in the list, only that item will be drawn with dotted symbology. Example 2: Defining Dotted Symbology Determine the table entry that will result in the dotted symbology on the isometric when the construction status is EXISTING, REVAMPED, RELOCATED, TEMPORARY, DISMANTLE or FUTURE.


7.20 NOMTO_CODE_LIST_VALUES __________________________________________________________________________________________________________________________________________________ This table is very much the same as the DOTTED_SYMBOLOGY_CODE_LIST table except that it is used to imply a status of no-mto based on the value of a code-listed attribute. When a component has a status of no-mto then it does not appear in the ISOGEN bill-of-material. This table can be used in addition to the no-mto attribute that explicitly defines a component to be no-mto. Again, only code-listed attributes can be used in this table. Refer to DOTTED_SYMBOLOGY_CODE_LIST_VALUES, page 7 - 75 for information on identifying a code-listed column. The format of an entry in this table is:

ST, SC, CT, CC, PT, PC, IT, IC, VTF, VAL1, VAL2, ... VALn

Where: ST, SC

defines a segment level column (from table 12) whose value might cause the piping to be no-mto.

CT, CC

defines a component level column (from table 34) whose value might cause a commodity item or specialty item to be no-mto.

PT, PC

defines a pipe column (from table 50) whose value might cause a piece of pipe to be no-mto.

IT, IC

defines an instrument column (from table 67) whose value might cause an instrument to be no-mto.

VTF

is the number of values to follow in the list VAL1 through VALn.

VAL1-VALn

are the values of the code-listed column which will imply that the item to be no-mto.

Example 1: Defining Components as No MTO Determine the table entry that would result in all components with the construction status of existing to be no-mto. This example is very similar to the example covered in the section DOTTED_SYMBOLOGY_CODE_LIST_VALUES and requires an identical table entry:

12, 20, 34, 32, 50, 27, 67, 29, 1, 3

7 - 78


7.21 SHOP_FABCAT_CODE_LIST_VALUES __________________________________________________________________________________________________________________________________________________ If the codelist number is not listed in the option file sections for SHOP_FABCAT_CODE_LIST_VALUES or OFFSHORE_FABCAT_CODE_LIST_VALUES, the item defaults to field. This table is used to identify those values of the fabrication category attribute that are to be interpreted as meaning shop. This is necessary because ISOGEN only allows the two options of either shop or field and does not distinguish (as PDS does) between supplier and fabricator of a component. If the codelist number is not listed in the option file sections for "SHOP_FABCAT_CODE_LIST_VALUES" or "OFFSHORE_FABCAT_CODE_LIST_VALUES" the item will default to field. ISOGEN lists shop materials separately from field materials. In erection-only isometrics ISOGEN does not list shop materials. Also, some end-prep graphics are changed to distinguish between connections made in the shop and those made in the field. Field connections are implied when the fabrication category changes from shop to field or viceversa. The format of the table entry is:

VTF, VAL1, VAL2, ... VALn

Where: VTF

is a number indicating the number of values to follow.

VAL1-VALn

are the values of the fabrication category attribute that are to be interpreted as meaning shop by ISOGEN.

Example 1: Segregating Fabrication Categories Define the table entry that would result in the fabrication categories Contractor supplied, shop fabricated (codelist value 5) and Shop supplied, shop fabricated (codelist value 15) being interpreted as meaning shop by ISOGEN.

SHOP_FABCAT_CODE_LIST_VALUES 1 2 5, 15

If needed, more than one row can be made in the table if the number of codelisted values per row exceeds 25.


Example 2:

7 - 80


7.22 OFFSHORE_FABCAT_CODE_LIST_VALUES __________________________________________________________________________________________________________________________________________________ If the codelist number is not listed in the option file sections for SHOP_FABCAT_CODE_LIST_VALUES or OFFSHORE_FABCAT_CODE_LIST_VALUES, the item defaults to field. The OFFSHORE section is optional and is not required in the options file. Also, refer to Offshore Material Category, page 8 - 9 and Offshore Fabrication Category, page 16 - 4 for related material. The format of the table entry is:

VTF, VAL1, VAL2, ... VALn

Where: VTF

is a number indicating the number of values to follow.

VAL1-Valn

are the values of the fabrication category attribute that are to be interpreted as meaning offshore by ISOGEN.

Example 1: Segregating fabrication categories Define the table entry that would result in the fabrication categories contractor supplied, offshore fabricated (code list value 39) and shop supplied, offshore fabricated (code list value 49) being interpreted as offshore by ISOGEN. The table entry is:

OFFSHORE_FABCAT_CODE_LIST_VALUES 1 2, 39, 49

If needed, more than one row can be made in the table if the number of codelisted values per row exceeds 25.


7.23 MOVABLE_TEXT __________________________________________________________________________________________________________________________________________________ This table allows you to relocate or turn off certain text strings and the north arrow generated by ISOGEN. If an item is not turned off, it can either be moved to its proper position in the drawing title block or moved into a drawing margin so this it is not a part of the plotted drawing. The maximum number of movable text entries is twenty five.

This table is also used to set-up/ define a table or matrix of spool numbers that you locate in your drawing. The format of a table entry is:

RECNO, X, Y, TXTHGT, XOFF, YOFF, DIR

Where: RECNO

is the record number of the item to be moved or turned off. When setting up a spool number table you set RECNO to -7. Other valid entries include any of the header record numbers defined for the PIPELINE_HEADER table (refer to PIPELINE_HEADER, page 7 - 50 ) or one of the following: Recno ______

Item _____

-25 -700 -701 -702 -703

System ID for multi-line isometrics drawing north arrow (reserved) sheet number on a drawing number of sheets on a drawing

X

is the x offset in 1/100ths mm from the bottom left corner of the sheet.

Y

is the y offset in 1/100ths mm from the bottom left corner of the sheet. Use x and y equal to 0 to turn off a text string.

TXTHGT

is the text height of the string being moved in 1/100’s mm (that is, text in mm X 100). 0 is the default setting as defined in the ISOGEN option switches.

7 - 82


XOFF

is the horizontal distance in 1/100ths mm between spool numbers in a spool number table. XOFF also defines the direction of travel for locating the next table entry in the row. If XOFF is negative the next table entry is to the left, otherwise it is to the right. Should be set to zero if RECNO is not -7.

YOFF

is the vertical distance in 1/100ths mm between spool numbers in a spool number table. YOFF also defines the direction of travel for locating the next table entry in the column. If YOFF is negative then the next entry is located below the current one, otherwise it is located above it. Should be set to zero if RECNO is not -7.

DIR

is a compound number that defines the size and filling order of a spool number table as follows:

ROWS defines the maximum number of rows in the spool number table. COLS defines the maximum number of columns in the table. TABLE DIRECTION defines the order in which the table is filled with values. If TABLE DIRECTION is set to 0 then rows of the table are filled in succession. If TABLE DIRECTION is set to 1 then columns are filled in succession. This parameter should be set to 0 if RECNO is not -7. Example 1: Defining Movable Text Define table entries that would turn off the system ID for multi-pipeline isometrics and any title block text generated by -41 through -45 records in the PIPELINE_HEADER table. The following table would accomplish this: -41, 0, 0, 0, 0, 0, 0 -42, 0, 0, 0, 0, 0, 0 -43, 0, 0, 0, 0, 0, 0 -44, 0, 0, 0, 0, 0, 0 -45, 0, 0, 0, 0, 0, 0 Example 2: Defining Movable Text The following spool table would result from the values XOFF=-700, YOFF=800, and DIR=1003004 (such as Table entry -7, 100, 100, 0, -700, 800, 1003004).


Certain ISOGEN text strings like the line name (-6 record) cannot be turned off. Do not set X and Y to 0. You can move these items outside the plotted area of the drawing to eliminate them.

Text is justified by the lower, left corner of the string.

If the number of spools on an iso sheet exceeds the number of table entries defined for a spool number table then the table is filled and an error message is written to the error file.

To position the default spool numbers (that is, where the spool number is surrounded by square brackets) in a spool number table you should not have a -7 entry in the PIPELINE_HEADER table. If you want to position only the number (without the square brackets) then insert an entry into the PIPELINE_HEADER table for the -7 record but set ST, SC, and SN to 0. Also set PREFIX to a blank. If you have defined a spool prefix in the PIPELINE_HEADER table then the entire spool number, including the prefix, will be positioned in the table.

7 - 84


7.24 NEW_SYMBOL_KEYS __________________________________________________________________________________________________________________________________________________ Certain ISOGEN interface logic depends on the ISOGEN symbol name. When ISOGEN symbols are redefined and renamed, this logic can not be properly executed. This table allows you to tell the interface software which user-defined symbol your new symbol is based upon so that the special logic can be properly executed. The format of a table entry is:

’SYMBOL KEY’, ’OLD SYMBOL KEY’

Where: SYMBOL KEY

is the name of your new ISOGEN symbol.

OLD SYMBOL KEY

is the name of the ISOGEN symbol upon which your symbol is based.

Example 1: >Defining ISOGEN Symbol Keys Define a table entry which indicates that the symbol RVXX has been redefined and named RRVV: ’RRVV’, ’RVXX’ An entry in this table is only required when the old symbol key (or the symbol upon which your symbol is based) is one of the following: CVXX, SVXX, MVXX, HVXX, XVXX, RVXX, IIXX, OPXX, PRXX, DRXX, CTXX or any symbol which you redefine and intend to map to a multi-endprep component in the model.


7.25 GENITM_NOTE_FORMAT __________________________________________________________________________________________________________________________________________________ This table is used to format notes for items that imply materials through the Implied Material Data Table and for valves with chain wheel operators, extension stems or floor stands. This table is enabled by Intergraph option 45.

The table can contain up to four entries that are used to format notes. The first entry is for valves with chain wheel operators. The second entry is for valves with floor stands. The third entry is for valves with extension stems. The fourth entry is for the note pointing to a component that generates implied items through the specification database. One note is formatted for each item implied through the specification database. A table entry is a text string as follows:

Label Definition

Where: The label definition is formed from text together with embedded specifications for attributes pertaining to the implied item. An embedded specification is formed by a number within square brackets (such as [n]). Valid numbers that can be used together with their meanings are: [1] [2] [3] [4]

The item code or commodity code of the implied item. The quantity of implied material. The material description of the implied material. The chain operator number, for chain wheel operators.

Example 1: Defining General Item Notes Show a note format that would display item code and quantity for an implied item: ’INCL. [2] - [1]’ When an implied item is generated through the reference database, the following example note might be generated in the drawing: INCL. 1 - WBAAACFHNB

7 - 86


Example 2: Defining General Item Notes Show an example note format for a chain wheel operator. ’INCL. CHAIN WHEEL OPTR. [1]$WITH [2] CHAIN’ The note generated on the iso might be: INCL. CHAIN WHEEL OPTR. CHAIN_3001 WITH 21’-0" CHAIN The note formats should be defined with upper case characters.

A dollar sign ($) embedded within the note will act as a line feed.


7.26 ALTERNATE_DESCRIPTION_INDEX __________________________________________________________________________________________________________________________________________________ This table is used to define which database attributes should be used as a secondary or alternate index into the material description libraries. Intergraph option 37 controls the use of this table.

The format of a table entry is: TYPE, TABLE, COL, LDL NO Where: TYPE

is a number that indicates the component type that is to have an alternate index into a material description library. Valid values for type are: 1 - Commodity item 2 - Specialty item 3 - Pipe 4 - Instrument 5 - Pipe support

TABLE, COL

LDL NO

is the table, column specification of the attribute that is to serve as the alternate index into a material description library. TABLE must correspond to TYPE as follows: TYPE ______

ALLOWABLE VALUES OF TABLE __________________________________

1 2 3 4 5

34 34 50 67 80

is a label description library number that defines a composite attribute that should be used in place of TABLE, COL for the alternate index.

Example 1: Defining Secondary or Alternate Indices for the Material Description Library Show the table entry that defines the secondary index for a pipe support to be the fixed string "PSUPPORT". The table entry would be:

5, 80, 0, 972

7 - 88


Where: Label 972 returns the string "PSUPPORT". It does not reference any attributes in the database record for the support. The attribute used as the primary index into the material description libraries is shown for each type below:

TYPE ______

Primary Index (TABLE, COL) ______________

1 2 3 4 5

34, 8 34, 2 50, 12 67, 2 80, 4

It is not possible to define a secondary index for implied materials (bolts and gaskets), for generated items (like the stub end for a lap joint flange) from the spec or for generated items from the Implied Material Data Table.


7.27 USER_DEFINED_IMPLIED_ITEM_BOM __________________________________________________________________________________________________________________________________________________ This table is used with the user-defined material take off feature. For more information, refer to User-Defined BOM / Material Control File, page 8 - 1 . Fields defined in this table will write information to the -80:-89 records for bolts and gaskets. The implied items table provides a means to map attributes that are: from the component that caused the item to be generated (e.g. flange pressure). from the spec entry for the implied item (e.g for the commodity code). from data calculated when the item is generated (e.g. bolt length). The format of an entry in this table is: TYPE, CT, CC, CLBL, PT, PC, PLBL, IT, IC, ILBL, ST, SC, CPF, ITEM, COLUMN, FLAG

Where: TYPE

defines the type of implied component that the table entry is to apply to. TYPE ______

TABLE ENTRY APPLIES TO ____________________________

1 2 3 4

Gaskets Only Bolts only Welds only All of the above items

Where: CT, CC

defines a table, column specification from a generating component that is to be mapped when the generating component is a COMPONENT or SPECIALTY ITEM. Valid values for CT are 0, 12 and 34.

CLBL

is the label description library number that defines the note format that will be retrieved and associated with the COLUMN field.

PT, PC

defines a table, column specification from a generating component that is to be mapped when the generating component is a PIPE. Valid values for PT are 0, 12 and 50.

PLBL

is the label description library number that defines the format of note which will be retrieved and associated with the COLUMN field.

7 - 90


IT, IC

defines a table, column specification from a generating component that is to be mapped when the generating component is an INSTRUMENT. Valid values for IT are 0, 12 and 67.

ILBL


ST, SC

defines a table, column specification that is to be mapped when the attribute is taken from the reference database entry for the implied item. Valid values for ST are 0 and 202.

CPF

is a connect point flag. When CPF is set to 1, it indicates that the attribute should be retrieved from the generating item’ s connect point (that is, the connect point from the item generating the implied material). NOTE: When this flag is set, CT, PT and IT should be set to 0. CC, PC, and IC should be set to a value selected from the Connect Point Attribute index in the USER_DEFINED_COMPONENT_BOM section.

ITEM

When this value is nonzero it indicates that either the attribute to be mapped is data that was generated along with the implied item, or the attribute to be obtained from the spec. Values for item are dependent on the implied item type as shown below. Item Type _____

Item _____

Description ___________

ALL

-1

BOLT

1 2

Use ST, SC to obtain the attribute from the reference database. Number of bolts Bolt Length in Project Units English for English Project Metric for Metric or Mixed Project Bolt diameter in Project Units English for English Project Metric for Metric or Mixed Project Number of nuts Bolt diameter - English Units Bolt length in English Units

3

GASKET WELD

4 5 6 0 1 2 3 4

Weld ID number Weld Type Material A Material B

COLUMN

is a number -80:-89 defined in the MATERIAL LISTING DEFINITION (MLD) file where the value will be displayed on the iso.

FLAG

is a special flag used to inhibit conversion of code-listed attributes to their ASCII string equivalents.


When information is generated for an item, the item type is determined and one of the previously listed table, column pairs is selected. The selected table, column pair is then used to retrieve an attribute from the database. All pairs need not be defined. If a component data table entry should apply to only one type of item, set the table, column pairs for other types to zero. If the label number is defined as anything other than 0, that value will be used in place of the table, column value or the value from connect point attributes.

Example 1:

1,

0,

1,

0,

0,

1,

0,

0,

1,

0,

0,

0,

1,

0, -80, 0

3,

0, -1, -81, 0

This table entry maps the gasket size to the -80 record.

2,

0,

0,

0,

0,

0,

0,

0,

0,

0, 202,

This table entry maps the item name from the reference database for the bolt to the -81 record.

2,

0,

0,

0,

0,

0,

0,

0,

0,

0,

0,

0,

0,

2, -82, 0

This table entry maps the bolt length to the -82 record.

4, 34,

0,

996,

0,

0,

0,

0,

0,

0,

0,

0,

1,

0, -83,

0

This table entry will generate a note to the -83 record when the current item is a bolt or gasket and the generating component is a COMPONENT or SPECIALTY ITEM. Label 996 defines the format of the note that would be generated and in this case the label will output the generating component fabrication category as the note.

7 - 92


7.28 USER_DEFINED_GENERATED_ITEM_BOM __________________________________________________________________________________________________________________________________________________ Fields defined in this table write information to the -80 - -89 records for items generated through the reference database (Table 212 Implied Items) and for chain wheel operators. The generated items table provides a means to map attributes that are: from the component that caused the item to be generated. from the reference database entry for the implied item (that is, for the commodity code). The format of an entry in this table is: CT,CC, CLBL, ET,EC, ELBL, PT,PC, PLBL, IT,IC, ILBL, ST,SC, SLBL, CPI, ITEM, COLUMN, FLAG

Where: CT, CC

defines a table, column specification from a generating component that is to be mapped when the generating component is a COMPONENT. Valid values for CT are 0, 12 and 34.

CLBL


ET, EC

defines a table, column specification from a generating component that is to be mapped when the generating component is a SPECIALTY ITEM. Valid values for ET are 0, 12 and 34.

ELBL


PT, PC


PLBL


IT, IC

defines a table, column specification from a generating component that is to be mapped when the generating component is an INSTRUMENT. Valid values for IT are 0, 12 and 67.

ILBL


ST, SC

defines a table, column specification from a generating component that is to be mapped when the generating component is a PIPE SUPPORT. Valid values for ST are 0, 12 and 80.


SLBL


CPI

is a connect point identifier that is used to access connect point attributes by connect point color (green or red) rather than by attribute number. When CPI is set (nonzero), CT, ET, PT, IT and ST should be set to zero and CC, EC, PC, and IC should be set to a value selected from the Connect Point Attributes index.

ITEM

CPI ____

Definition __________

1 2

retrieve a green connect point property retrieve a red connect point property

ATT _ ___

Connect Point Attributes _ ______________________

1 2 3 4 5 6 7 8 9 10 11 12

nominal piping diameter outside diameter end preparation schedule/thickness pressure rating stress analysis node number face to center distance bolt type override gasket separation stress intensification head loss factor signal line type (instruments only) where *C represents either CC, EC, PC, or IC

When the value is set to 1 it indicates that the attribute to be mapped is data from the reference database. The value for CC, EC, PC, IC and SC should be set according to the table shown below when ITEM is set to 1. ATTR ______


1 2

Generated item commodity code Generated item quantity

COLUMN

is a number -80 - -89 defined in the MATERIAL LISTING DEFINITION (MLD) file where the value will be displayed on the iso.

FLAG

is a special flag that is normally 0 but is set to 1 to inhibit conversion of code-listed attributes to their ASCII string equivalents. When FLAG is set to 1, the code-list number will be placed in the record. When information is generated for an item, the item type is determined and one of the previously listed table, column pairs is selected. The selected table, column pair is then used to retrieve an attribute from the database.

7 - 94


All pairs need not be defined. If a component data table entry should apply to only one type of item, set the table, column pairs for other types to zero. If the label number is defined as anything other than 0, that value will be used in place of the table, column value or the value from connect point attributes.

Example 1:

34,

3,

0, 34,

3,

0, 50,

3,

0, 67,

3,

0, 80,

4, 0, 0,

0, -80, 0

This entry maps the item name of the component that generates some implied material to the -80 record.

0,

2,

0,

0,

2,

0,

0,

2,

0,

0,

2,

0,

0,

0, 0, 0,

1, -81, 0

This entry maps the generated item quantity to the -81 record. In the case of a chain wheel operator, this entry corresponds to the length of chain.


7.29 USER_DEFINED_COMPONENT_BOM __________________________________________________________________________________________________________________________________________________ Fields defined by this table appear in component, specialty item, pipe, instrument and pipe support records. The format of an entry in this table is:

CT, CC, CLBL, ET, EC, ELBL, PT, PC, PLBL, IT, IC, ILBL, ST, SC, SLBL, CPI, COLUMN, FLAG

Where: CT, CC

defines a table, column specification for the case when the current item is a component. Valid values for CT are 0, 12 and 34.

CLBL


ET, EC

defines a table, column specification for the case when the current item is a specialty item. Valid values for ET are 0, 12 and 34.

ELBL


PT, PC

defines a table, column specification for the case when the current item is a pipe. Valid values for PT are 0, 12 and 50.

PLBL


IT, IC

defines a table, column specification for the case when the current item is an instrument. Valid values for IT are 0, 12 and 67.

ILBL


ST, SC

defines a table, column specification for the case when the current item is a pipe support. Valid values for ST are 0, 12 and 80.

SLBL


CPI

is a connect point identifier. It is used to access connect point attributes by connect point color (green or red) rather than by attribute number. When CPI is set (nonzero) then CT, ET, PT, IT and ST should be set to zero and CC, EC, PC, and IC should be set to one of the values shown in the following index.

7 - 96


CPI ____

Definition __________

1 2


ATT _ ___


1 2 3 4 5 6 7 8 9 10 11 12

nominal piping diameter outside diameter end preparation schedule/thickness pressure rating stress analysis node number face to center distance bolt type override gasket separation stress intensification head loss factor signal line type (instruments only) where *C represents either CC, EC, PC, or IC

COLUMN

is a number -80:-89 defined in the MATERIAL LISTING DEFINITION (MLD) file where the value will be displayed on the iso.

FLAG

is a special flag that is normally 0 but is set to 1 to inhibit conversion of code-listed attributes to their ASCII string equivalents. When FLAG is set to 1, the code-list number will be placed in the record. When information is generated for an item, the item type is determined and one of the previously listed table, column pairs is selected. The selected table, column pair is then used to retrieve an attribute from the database. All pairs need not be defined. If a component data table entry should apply to only one type of item, set the table, column pairs for other types to zero. If the label number is defined as anything other than 0, that value will be used in place of the table, column value or the value from connect point attributes.

Example 1:

34, 3, 0, 34, 3, 0, 50, 3, 0, 67, 3, 0, 84, 4, 0, 0, -80, 0 This table entry maps the item name attribute for all component types to the -80 record.

34, 4, 0,

0, 0, 0, 50, 4, 0,

0, 0, 0,

0, 0, 0, 0, -81, 0

This table entry maps the new item name attribute for component types of COMPONENT and PIPE to the -81 record. Nothing is generated in the record for SPECIALTY ITEMS, INSTRUMENTS or PIPE SUPPORTS by this table entry.


0, 1, 0,

0, 1, 0,

0, 1, 0,

0, 1, 0,

0, 0, 0, 1, -82, 0

This table entry maps the GREEN nominal pipe size (also referred to as size 1) to the -82 record. Since PIPE SUPPORTS do not have connect point properties, no number is specified for them in the table entry.

0, 1, 0,

0, 1, 0,

0, 1, 0,

0, 1, 0,

0, 0, 0, 2, -83, 0

This table entry maps the RED nominal pipe size (also referred to as size 2) to the -83 record.

0, 4, 0,

0, 4, 0,

0, 4, 0,

0, 4, 0,

0, 0, 0, 1, -84, 0

This table entry maps the GREEN schedule (schedule 1) to the -84 record.

12, 14, 0, 12, 14, 0, 12, 14, 0, 12, 14, 0,

0, 0, 0, 0, -85, 0

This table entry maps the insulation purpose attribute from the segment to the -85 record for all items except PIPE SUPPORTS.

12, 22, 0, 12, 22, 0, 12, 22, 0, 12, 22, 0,

0, 0, 0, 0, -86, 1

This table entry maps the paint code CODE_LIST VALUE from the segment to the -86 record. The code-list value is put in the record rather than the attribute itself because FLAG is set to 1 and the attribute being mapped is code-listed.

34,

0, 994,

0,

0,

0,

0,

0, 0,

0,

0, 0,

0, 0, 0, 0, -87, 0

This table entry will generate a note to the -87 record when the current item is a component. Label 994 defines the format of the note that would be generated, and in this case the label will output the component fabrication category as the note.

7 - 98


7.30 NON_DIMENSIONED_SUPPORTS __________________________________________________________________________________________________________________________________________________ This feature allows you to select all pipe supports and hangers without dimensioning that are displayed on an isometric. The format of a table entry is:

NON_DIMENSIONED_SUPPORTS 1 3, PS1, PS2, PSP1

Where: 1

is the number of lines to follow

3

is the number of values to follow

PS1, PS2, PSP1

are the pipe support model codes that will be displayed, but not dimensioned. For more information on other ISOGEN dimensioning features, refer to Dimensioning and Coordinate Output, page 17 - 1 .

User-Defined BOM / Material Control File 8 - 1

8. User-Defined BOM / Material Control File

__________________________________________________________________________________________________________________________________________________

The ISOGEN package allows you to define (within certain limits) the layout and content of the ISOGEN generated Material List and related Material Control File. By making modifications to the Material List Definition (MLD) file and options file you can: Revise the Material List Style. — The current basic style with new optional column for weight - Style 1. — Placing user-defined data in a column-type layout - Style 2. This style is defined and controlled by the new Material List Definition (MLD) file. MTO list header information is included in the material list definition file (MLD). — Placing data in a column-type format (no headings) on a user-defined drawing sheet - Style 3. This style will be defined and controlled by the new Material List Definition (MLD) file. The MTO list header information is displayed in the iso border file. Create a user-defined Material Control File. This file is defined and controlled by the new Material List Definition (MLD) file. The MLD file is the 13th entry in the FILES section of the ISOGEN options file. Create a new Offshore Material category. Define optional material accumulation parameters. Select part number ID box format on the plotted isometric Define the Optional output of the Length format of pipes, miscellaneous components and pipe length. Define a full range of Bolt Units (size X length). Revise the format of the cut list. Define welds to be included on the material list. Re-position the tile block. Reserve an area for a user-specified title block. When using the new user defined formats, it is recommended that several trial runs are done. This way, you can verify that the layout is practical and that the requested data is both valid and available, before committing to project use.

8-2


Validity checks will be performed on the contents of the MLD file and warning messages output when necessary. Typical checks validate all major headings and all data identifiers. A check is also done to confirm that all mandatory data is included in the file.

User-defined MTO - Related Information The following is a list of related elements within the ISOGEN software that may be manipulated when creating a user-defined BOM or Material Control file. Related ISOGEN Options (Appendix B) ISOGEN Options: 2, 23, 24, 25, 26, 27, 28, 29, 30, 35, 65, 73, 74 Related Intergraph Options (Section 7) Intergraph Option:

8, 10, 14, 22, 29, 30, 33, 36, 37, 45, 47, 50, 52, 54, 56, 62

Related Options File Material (Section 7) USER_DEFINED_COMPONENT_BOM USER_DEFINED_IMPLIED_ITEM_BOM USER_DEFINED_GENERATED_ITEM_BOM Also: The thirteenth entry in the FILES Section of the options file: MLD file (See Chapter 8) Related ISOGEN ATEXT Records (Appendix B) -322, -323, -339, -356 - -363, -365, -367, -368 - -378, -415 - -419, -421 - -423, -455

8.1 Types of Material List __________________________________________________________________________________________________________________________________________________ Three types of material lists are available Style 1, Style 2 and Style 3. ISOGEN option switch 23 controls which Style material list is used. The MLD file contains the definition of the content and format of Style 2 and Style 3 Material Lists. Style 1 - Standard Material List To produce a material list identical to those produced prior to the 5.0 ISOGEN software release, turn off the intermediate sub-headings (PIPE, FITTINGS, FLANGES, etc). This can be done by setting the appropriate Atexts to BLANK. This will continue to provide the capability of producing a continuous-type material list. A 4.3 version of the ISOGEN options file can be used without any modifications to produce an iso with the 5.0 software that looks as it did when it was produced with the 4.3 software. Style 2 - User-defined Variation of the Standard Material List


Style 3 - User-defined Text and User-positioned Text Only text is output. No headings are output. Style 3 works well for boxed or column type bills of material. The Cut List and Center Line Summary facilities are not available for Style 3.

Basic Contents of a Style 1 Material List Standard form Material List (as currently output and using all current sort criteria) New column for component weight (optional) New section for Offshore materials Revised Cut List (optional) New form of the Bolt size x length output An option for repositioning the title block when Material List on the right is used. Basic Contents of a Style 2 Material List User variation of the Style 1 material list User-definable column headings/data content for horizontal layout (done in the MLD file) Extra data attributes available for listing (This can be done by using the 80- 89 record identifiers in the MLD file.) Similar vertical layout to Style 1. (uses the same sort criteria) All options listed for Style 1 Facility for User to change sort group of components. (For example, move Blank Flange from Valve/In-Line Item group to Flange group) Basic Contents for a Style 3 Material List Fully user-defined drawing backing sheet (All column, boxes, headings, etc pre-defined in the seed isometric or border file) Three major categories of Materials to be identifiable (For example, FABRICATION, ERECTION, OFFSHORE) No intermediate Material Type headings to be output User-definable data content and data output positions for all material list information in the MLD file

8-4


Extra data attributes available for listing (This can be done by using the 80- 89 record identifiers in the MLD file Material Listing UP/DOWN facility For example:

listing listing listing listing

TOP to BOTTOM BOTTOM to TOP Fab Materials DOWN/ Erec Materials UP Erec Materials DOWN/ Fab Materials UP

If the Offshore category is used, you are restricted to using a continuous list (Top to Bottom/Bottom to Top) and should use the column for category identification (For example, FAB, EREC, OFF ). Automatic ISO overflow facility (used if there are too many parts for the given backing sheet)

8.1.1 Operating Requirements __________________________________________________________________________________________________________________________________________________ The following requirements must be met to successfully use the user-defined BOM / Material Control File functionality. Material List Definition (MLD) File This will be a required entry when using the user-defined bill of material (Style 2 or Style 3). The options file section titled FILES will require a new entry (the 13th entry) defining the location and name of the user-defined MLD file. Bill of Material Columns. You must define data to be output on the MTO for each component type in the MLD file. This done by using new or existing data identifiers. Existing BOM identifiers are Commodity Code (-20 record) or Commodity Description (-21 record). New BOM identifiers consist of user-defined identifiers: — -80 - -89 record types — PT-NO, QTY, N.S., WEIGHT, CATEGORY, GROUP The user-defined identifiers can contain anything from the database for a specific component. Three sections (see below) of the Intergraph options file define reported information and the identifier that is associated with that information (-80 - -89 record types) per item type. The -20 and -21 record types can not be redefined. You will not be required to output either of these record types on the user-defined BOM, but the .idf file will always contain these two records.


Type -80 identifiers, if any, will always follow the -21 record type in the .idf file.

User-defined information can be formatted by manipulating the following three sections in the options file. USER_DEFINED_COMPONENT_BOM - used with components, engineered items, pipe, instruments and supports. USER_DEFINED_IMPLIED_ITEM_BOM - used with bolts, gaskets and welds. USER_DEFINED_GENERATED_ITEM_BOM - used with cap screws and chain wheel operators. To generate an entry in the bill of material for generated items, Intergraph option 45 must be set to 1 or 3.

8-6


8.2 Material List Definition (MLD) File __________________________________________________________________________________________________________________________________________________ The options file section titled FILES will require a new entry (the 13th entry) defining the location and name of the user-defined MLD file. The new entry in the FILES section will be verified, mounted and included as a -122 record type in the .idf file. This entry is required when using the user-defined bill of material. The MLD file allows you to define (with certain limits) the style and content of the following: The Heading content and layout of a PRINTED Style 1 (Weight Heading only) or Style 2 Material List. The column headings, data content definitions and positional coordinates of the main body of a plotted and/or printed Style 2 Material List. The main body of a Style 1 (current style) plotted or printed material list can not be changed. For a Style 2 type Material List the BASIC FORMAT is the same as the current style. The number, position, and content of the various vertical data columns is the part of the list that is user definable. The data content and positional coordinates for all items on a plotted Style 3 Material List. When using a Style 3 Material List, the option of obtaining a printed list is not available. The layout/data content of a user-specified Material Control File. Because of the current methods used within the ISOGEN program, the quantities included in the Material Control File must be identical to the quantities generated for the Material List. This is because the same accumulation rules are used for both.


8.3 User-Defined Material Control File (.bom file) __________________________________________________________________________________________________________________________________________________ When Intergraph option 1 is set to 1, the MLD file allows you to define the layout and content of the printed Material Control File (M/C File). The Material Control File is intended to be used as a vehicle for data transfer between ’Systems’. There will be several differences in layout when compared with the file generated for a Printed Material List (.prt file). Basic Requirements for a Material Control File Allow any width (Not limited to 132 characters). Allow any length of file. No ’Paging’ functionality is required. Include any Title Headings/Column Headings (if user-defined) once at the start of the file. Output of lengths in any quantity (QTY) column should be in the format set in ISOGEN option switch 24. Bolts to be included in the file should follow the same rules as the bolts used for the associated material list. Size and length units are set by ISOGEN option switch 65. Use ATEXT -359 to reformat the size and length information. The ISOGEN software allows you to identify all UNITS used within the M/C file through the use of Unit Identification entries. There is no limit on the number of Unit Identification entries and the format is user-definable. Unit ID entries must be included in the MLD file and immediately follow the MATERIAL-CONTROL-FILE identifier. Any unit id entries will be the first items output in the M/C file. Unit identification entries will not impact the ISOGEN system. Their only purpose is to identify the UNITS used for size and lengths in the M/C interface file. Some typical unit ID entries:

UNITS-BORE data UNITS-LENGTH data UNITS-BOLT-DIA data UNITS-BOLT-LENGTH data

Where: data identifies the units used in the M/C file.

8-8


A user-defined Material Control file will be triggered by the identifier MATERIALCONTROL-FILE which is located in the MLD file. The definition of the required file (layout/content) will follow the MATERIAL-CONTROL-FILE identifier. The file can be generated either with or without Titles and/or Column Headings. The definition of Title Headings, Column Headings and Data Items will use the same basic rules as a Style 2 printed material list. The key identifiers to be used are:

PRINTED-M/C-TITLES PRINTED-M/C-COLUMN-HEADINGS PRINTED-M/C-DATA-ITEMS

In the case of Data Items, the -39 IDF RECORD IDENTIFIER can be included in the Material Control file, but not on the Material List. This can only be used when using the Material List Non-Accumulation facility (ISOGEN option 74). Available Data Items for the Material Control File Unique Name _____________

IDF Record Number ___________________

PIPELINE-REFERENCE DRG PIPING-SPEC PT-NO QTY N.S. ITEM-CODE DESCRIPTION WEIGHT CATEGORY GROUP

-6 -11 -20 -21 (uses ATEXT -376 - 378) uses ATEXT -307, -308, -309, -311 - -315, -339, -375 -80 - -89 (user-defined attributes) -39 Segment and Component Occurrence Numbers

UNIQUECOMPONENTIDENTIFIER

If Unique Name and associated IDF Record Number both exist, either may be used. UNIQUE NAMES with no IDF Record Numbers are shown with a - in the IDF RECORD NUMBER column. When this occurs, you must use UNIQUE NAME. IDF Record Numbers with no UNIQUE NAME are shown with a - in the Unique Name column. When this occurs, use IDF Record Number.


8.4 Offshore Material Category __________________________________________________________________________________________________________________________________________________ Any item designated as Offshore will be treated as an ERECTION type item in the drawing, but will be listed on the Material List under a new main heading as defined by ATEXT -371. All materials sorted are within the new heading category. The M/C file will contain a 3 in word 6 of existing component records when the item is designated as Offshore.

8.5 Transferring Components Between Sort Groups __________________________________________________________________________________________________________________________________________________ The MLD file has a TRANSFER feature that will allow you to move components from one sort group to another. The identifier TRANSFER must be followed by any relevant information that would identify the component to be transferred and the new group under which it will be listed. Component identification will be done by record ID numbers. Refer to the Record Identification Numbers listed in Appendix B of this document (35 =Elbow, 100 = pipe). Available sort Group identifiers include: PIPE VALV FITT INST FLAN SUPP GASK MISC BOLT WELD

pipe valves + inline items fittings instruments flanges supports gaskets miscellaneous components bolts welds

If you plan to list any of the above Group Identifiers on a Style 2 or Style 3 Material List, ATEXTs -307, -308, -309, -311, -312, -313, -314, -315, -339, and -375 must be set in the options file. A typical entry in the MLD file might be:

TRANSFER 107 FLAN

Where:

8 - 10

107


is the record ID for BLANK FLANGES and FLAN is the NEW sort group under which Blank Flanges should be listed. Any number of blank characters between record ID and Group identifiers are allowed.

8.6 Generating an Optional Format for Length Output __________________________________________________________________________________________________________________________________________________ By default, length output on the Material List for PIPE, MISCELLANEOUS COMPONENTS and CL LENGTH is set to the nearest 1/10 M or 1/10 FT and is formatted:

Metric 10.4 M English 10.4 ’

ISOGEN option 24 allows for an alternative format to output either in millimeters or feet and inches.

Metric 1040 mm English 10’-5"

(rounded to the nearest mm) (rounded up to the nearest inch)

8.7 Bolt Units (size x length) __________________________________________________________________________________________________________________________________________________ Option switch 65, Bolting Length in the M/C file, allows you to define bolt length/bolt diameters. Any value set in the last position of ISOGEN option switch 65 is output in the second digit (tens position) of word 2 in the 60 type record in the M/C file. Any value set in the second position of ISOGEN option switch 65 is output in the third digit (hundreds position) of word 2 of the 60 type record in the M/C file. Bolt diameters (in word 2) and bolt lengths (in word 7) of 500 (bolt) records in the M/C file will be generated in the units appropriate to the various ISOGEN switch settings. The Material List also allows an alternative output format for bolts. The alternative output will be used whenever ATEXT -359 is set to any value other than blank. The suggested setting is diameter x length.

ISOGEN will always output in a bolt-diameter-by-bolt-length order. Bolt Units will be placed just below the new heading using a program generated text string. The text string is created by using a combination of ATEXTs -330 and -331. Typical Bolt Unit Output: BOLTS _______ Bolt Descr.

DIA x LENGTH (INS x INS) 3/4 x 2.1/2

(ATEXT -359) (Generated)


8.8 Generating a Revised Format of the Cut List __________________________________________________________________________________________________________________________________________________ Modifications made to the current cut list format ATEXT -322 (Cut) is ignored. ATEXT -323 (Length) is moved up to the top line of the headings. Set ATEXT -361 so that the default text, Ft-Ins, will be positioned below LENGTH when imperial units are being used. Place ATEXT -331(mm) below LENGTH when mixed or metric units are being used. Set zero inches to output as 2’0" and not 2’. The revised layout still has two cut pieces on each line.

Typical layout:

PIECE NO.

LENGTH N.S. (FT-INS) (INS)

REMARKS

PIECE NO.

LENGTH (FT-INS)

N.S. (INS)

REMARKS

New cut list format The new cut list format has a revised layout with only one cut piece per line. To request the new cut list format, use ISOGEN option 2. Typical new layout:

PIECE NO.

LENGTH (FT-INS)

N.S. (INS)

END ONE

END TWO

ITEM CODE

— OR —

PIECE NO.

LENGTH (FT-INS)

N.S. (INS)

END ONE

END TWO

ITEM CODE

Gaps between new heading elements are handled by the ISOGEN software based on either the actual Atext heading or the length of the information items that are printed under each heading. This will be either the standard Atext or any user-modified Atext.

8 - 12


When using the new cut list format, you must verify that the total width of the cut list is less than the width of the requested material list. This will prevent the cut list from overflowing onto the drawing section of the isometric. Use ATEXTs -362, -363, -364, -365 when using the new cut list format. If PART NO. is required on the cut list instead of ITEM CODE, ATEXT -364 should be blank and ATEXT -365 set to PART$NO. The Cut List Remarks Column Current Atexts for cut list REMARKS (-326, -327, -328) are still used. If any of these Atexts are changed, sufficient space should be left between column headings to accommodate data. In the new cut list format layout, multiple remarks are allowed. Each remark is located on a separate line. For example:

REMARK LOOSE FLG FF WELD

Multiple occurrences of the same remark will be output in the form PLD BEND (2) where the last 2 characters are automatically generated. End One and End Two Columns Entries in these columns describe the operations performed in order to prepare the ends for fabrication. Five ATEXTs (-366 - -370) are available to identify the five basic operations that can be recognized by the ISOGEN system. For the new cut list format, certain items must be treated as BWs (Butt Welds), but do not have the BW end condition as part of the SKEY. These items include: Flanges (105/106) FLWN - Flange Weld Neck FOWN - Flange Orifice Weld Neck FLSE - LJSE Butt Weld Type All other 105’s and 106’s to use Square Cut The type of end preparation on pipe is determined by the SKEY of the fitting or by the weld type. For weld types: SKEYS WW, WS, WF, assume BW end preparation.


8.9 Welds in the Material List __________________________________________________________________________________________________________________________________________________ When using INTERGRAPH option 62 and ISOGEN option 64, welds can be added to the Material List. Welds can be displayed in any of the Fabrication/Erection/Offshore sections of the Material List. To list welds in the last position of each section of the Material List, use the heading defined by ATEXT -375. Welds added to the Material List will not be included in the standard M/C interface file. It is a user option in any user-defined M/C file. Accumulation of welds is controlled by ISOGEN option switch 74. Weld part numbers are not normally indicated on the plotted iso section of the isometric. If needed, ISOGEN option 73 with a Style 3 for weld part numbers can be used to place weld part numbers.

8.10 Style for Fabricated (Pulled) Bends Output __________________________________________________________________________________________________________________________________________________ By using ISOGEN option 23 (position B), the outputs Bend Angle and Bend Radius can be displayed for pulled bends. The following is a typical revised output using the Style 1 and Style 2 Material Lists. Description ___________

NS ___

QTY _____

U03 Fabricated (Pulled) Bend 3.0D Bend Radius Angle 85.0

1

1

Part numbers less than 10 have a zero included (For example, U03 and not U3). Bend radius messages will use ATEXT -337 for bends expressed in number of diameters. (For example, 3.0D Bend Radius). A bend radius expressed in mm or Ft/Ins uses ATEXT -338 with the actual radius listed. (For example, 450 mm Bend Radius or 1’-6" Bend Radius). ATEXT -374 is used to generate the ANGLE text element in a format such as 85.0 (for an 85 degree angle).

8.11 Style for Material List Output __________________________________________________________________________________________________________________________________________________ When using ISOGEN option switch 23, position A and B, with setting 10 or 11: The current form of output is sorted into the categories, Fab/Erec/Offshore, with sub-groups of Pipe, Flanges, Fittings, etc. within each category. Except for the addition of the new Weld sub-group, there is no change to the Material List that is currently generated. When Using ISOGEN option switch 23, position A and B, with setting 20 or 21:

8 - 14


An alternative form of output that has no separate Fab/Erec categories and no sub groups is generated. This creates a continuous Material List with component and welds listed in the order they were found in the intermediate data file (.idf file). This does not apply to Gaskets and Bolts that are accumulated; they are printed in the weld list as the first occurrence of each type.

8.12 Positioning the Title Block __________________________________________________________________________________________________________________________________________________ ISOGEN option 25 allows you to either turn off or reposition the Title Block to the bottom of the Material List. ISOGEN calculates the height of the Title Block and draws a horizontal line between the two vertical lines that form the Material List boundaries. Checks are then made on ATEXTs -317 and -318. If they are not set to blanks and have not been positioned, the CL summary is positioned above the Title Block. ISOGEN option switch 35 reserves an area at the bottom of the Material List.

8.13 MLD File Content __________________________________________________________________________________________________________________________________________________ Heading Definitions for a Style 2 printed material list (ISOGEN MTO neutral file) in the MLD file contain three types of information items: A Heading Title element An associated data item to be listed with the Title element A basic activity identifier. All data items may be identified by either ’NAME’ or their .idf file record ID Number. A typical MLD file layout for a Style 2 Printed Material List heading would be:

PRINTED-MATERIAL-LIST TITLES PAGE ’ ’ ’Blank’ ’Blank’ PIPELINE REF :- ’-6’ PROJECT NO. :- ’-9’ ’Blank’ AREA REF :- ’-10’ REVISION NO. :- ’-8’ ’Blank’ PIPING SPEC :- ’-11’ DATE OF RUN :- ’-14’ ’Blank’ ’Blank’

The normal Material List would then be printed. This would be either the normal Style 1 list or any Style 2 list that you have defined. In the previous example:


’’

is used with the page attribute and indicates a program generated page number.

’Blank’

indicates a blank line. Titles will be output at the top of each new page. Number of lines per page will be taken from the existing option switch 63.

Items Available for Output as Part of a Printed Material List Heading Unique Name _____________

IDF Record Number ___________________

Pipeline-Reference Drawing Piping-Spec Nominal-Class Nominal-Rating Date-DMY Pipeline-Temp System-Reference Page

-6 -11 -12 -12 -14 -19 -25

Column Headings and Data Content Guidelines for Style 2 Material List Maximum heading width should not exceed 130 characters. There should always be the same number of data items as column headings unless space is left for future data additions. Column headings in the MLD file, must use the exact format of the required listing followed by the relevant data items to be printed. Each name (identifier) must be enclosed in single quotation marks.

8.14 MLD File Format Guidelines __________________________________________________________________________________________________________________________________________________ As a general rule, all heading and title formatting must be positioned in the MLD file exactly as it is to be positioned on the printed output. Title elements, other than unique identifiers, can be used with any format. Data item identifiers will be enclosed in single quotation marks. Unique identifiers are used to determine what is defined and must match exactly. These identifiers include: — STYLE2-COLUMN-HEADINGS — STYLE2-DATA-ITEMS The format must be headings followed by data items. — Blank characters can be used as required.

8 - 16


— Blank columns are allowed. — Use a | character to indicate vertical column positions. Column headings can be any ascii string. Data items must carry the following: — A data item identifier — A start position along the horizontal line — A justification marker. Data Item Identifiers can be defined by using a Unique Name or, where applicable, the IDF Record Number (For example, ’Item-Code’ -30 L or ’-20’ 30 L). If a separation line is required on the generated Material List to separate the PART NO. column from the rest of the List, a | character should be inserted in the required position on the last line of the column headings. If an indicator is not found, the Material List will be generated without a separation line. If the PT-NO (part number identifier) column is located at the extreme left or right side of the Material List, ISOGEN will generate the vertical dividing line to separate the part numbers from the remaining items. A | character should be inserted end the end of the last line of the column headings to indicate where the right border line of the Material List is required (For example, two spaces beyond the maximum width of the last data item). Justification Markers R L N

Right Justified Left Justified A true number field. If N is used as a decimal number (Real) the decimal point will be positioned in the selected column. If N is not used as a decimal number (Integer), the units digit is positioned in the selected column.

Style 2 and Style 3 Data Item Identifiers The following values are available for use as Data Identifiers in the MLD file for Style 2 and Style 3 MTO’s. The allowable justification for each record is also listed. Unique Name ______

IDF Record Number _______________

Allowable Justification ____________

PT-NO QTY N.S. ITEM-CODE DESCRIPTION WEIGHT CATEGORY

-20 -21 uses ATEXT -376 - 378

L or R N (fixed) L (fixed) L or R L (fixed) N (fixed) L or R


GROUP -

uses ATEXT -307 - -309, -311 - -315, -339, -375 -80 - -89 (user-defined attributes) -39 Only used on Material Control listings, Segment and Component Occurrence Numbers

L or R L (fixed) L or R

When Unique Name and associated IDF Record Number both exist, either may be used. Unique Names with no IDF Record Numbers are shown with a - in the IDF Record Number column (PT-NO, QTY,N.S., WEIGHT). When this occurs, use the Unique Name. IDF Record Numbers with no Unique Name are shown with a - in the Unique Name column. When this occurs, use IDF Record Number.

8.14.1 Style 3 Material List __________________________________________________________________________________________________________________________________________________ A Style 3 Material List requires a backing sheet (drawing frame) that contains a reserved area for Material List information. The precise format is user-definable, but no column headings are defined in the MLD file. All column headings must already exist in the seed or border design files. This style of output requires two types of information. — STYLE3-CONTROLS — STYLE3-DATA-ITEMS Basic Control Information for a Style 3 Material List Unless otherwise stated, where a number is required it will be integer or in real mm’s with only one decimal place allowed. Unless otherwise stated, all of the following inputs are mandatory. Define the type of list that will be generated (sectionalized, continuous, etc.). Valid types include:

Continuous-Down Continuous-Up Fabrication-Down Fabrication-Up Erection-Down Erection-Up Offshore-Down Offshore-Up Erection/Offshore-Down Erection/Offshore-Up

8 - 18


These will be used as either single entries or multiple entries depending on the form of list required. Identify start positions for information using the format: Start-Position XPOS YPOS

Where: XPOS and YPOS is the x and y location in the design file Define vertical spacing between each line of horizontal text using the format: VERTICAL-SPACING value

Define the maximum number of lines that can be printed before automatic overflow onto another sheet occurs. This number can be defined for the complete list or on a section-by-section basis if the section function is being used. Use the format: MAXIMUM-ENTRIES value

Where: value is an integer Define the character height to be used for material list information using the format: TEXT-HEIGHT value

Define the level where material list information should be placed (optional). Using the format: DRAWING-LAYER value

Where: value is a level 1 - 63 Define character weight (optional). Using the format: TEXT-THICKNESS value Where: value is a weight 0 - 10 Style 3 Data Item Information Data items must specify a data item identifier and start position information. Identifiers -80 - -89 must carry the maximum number of characters allowed on each print line. Start position is the x position in mm’s that identifies the bottom left hand point of the text string to be plotted. All text will be LEFT justified. Example Input: Data Item Identifier ITEM-CODE -80

Xpos 225.0 280

Max char 47


See the previous table under the heading Style 2 and Style 3 Data Identifiers for a list of Style 3 Data Identifiers.

8.15 Example User-defined Material List - Style 2 __________________________________________________________________________________________________________________________________________________ STYLE2-COLUMN-HEADINGS

PART SIZE NO. (INS)

ITEM CODE

COMPONENT DESC.

QTY

BLT DIA

BOLT LNGTH

NUTS/ BLT

MODEL CODE

SCH/ RAT

END PREP

MATL GEOM GRADE STD

’blank’

STYLE2-DATA-ITEMS

’PT-NO’ 2 ’N.S.’ 6 ’ITEM-CODE’ 13 ’DESCRIPTION’ 26 ’QTY’ 58 ’-80’ 79 ’-81’ 85 ’-82’ 92 ’-83’ 97 ’-84’ 107 ’-85’ 68 ’-86’ 73 ’-87’ 62

R L L L N L L L L L L L L

11 28 5 5 5 10 15 10

!Model Code !GCP Sch/Rat !End Prep !Matl Grade !Geo Std !Bolt Length !Nuts/Bolt !Bolt Diameter

8.16 Example User-defined Material List - Style 3 __________________________________________________________________________________________________________________________________________________ Continuous Down Type :

STYLE3-CONTROLS START-POSITION VERTICAL-SPACING TEXT-HEIGHT 2.5 DRAWING-LAYER CONTINUOUS-DOWN MAXIMUM-ENTRIES TEXT-THICKNESS STYLE3-DATA-ITEMS | Typical Data

225.0 4.5 15 55 2

190.5

8 - 20


Fabrication-Down, Erection-Up Type:

STYLE3-CONTROLS VERTICAL-SPACING TEXT-HEIGHT 2.5 TEXT-THICKNESS DRAWING-LAYER MAXIMUM-ENTRIES FABRICATION-DOWN START-POSITION ERECTION_UP START-POSITION

4.0 3 15 37 225.0

190.5

225.0

42.0

STYLE3-DATA-ITEMS | Typical Data

Split Type:

STYLE3-CONTROLS VERTICAL-SPACING TEXT-HEIGHT 2.5 TEXT-THICKNESS DRAWING-LAYER FABRICATION-DOWN START-POSITION MAXIMUM-ENTRIES ERECTION_DOWN START-POSITION MAXIMUM-ENTRIES Offshore_DOWN START-POSITION MAXIMUM-ENTRIES

4.0 2 15 225.0 14

190.5

225.0 14

130

225.0 7

70

STYLE 3-DATA-ITEMS Typical Data

Creating Seed Files for Extraction 9 - 1

9. Creating Seed Files for Extraction

__________________________________________________________________________________________________________________________________________________

To extract and plot isometrics, create a seed design file and a seed plot request file. The seed file names are keyed in at the Interactive Isometric Extraction form and the Define Default Set form (see Interactive Isometric Extraction, page 3 - 1 and Define Default Sets, page 5 - 13 for more information).

9.1 Creating an Isometric Seed File __________________________________________________________________________________________________________________________________________________ The isometric seed file is an empty MicroStation design file that the system copies before creating a new isometric. The seed file usually contains a single reference file consisting of the drawing border and title block. To create an isometric seed file: 1.

Copy one of the product option files (defaults.dat, mxdefaults.dat, etc.) and set ISOGEN options block word 14 for one of the standard drawing sheet sizes, or words 15 and 16 for a nonstandard sheet size. Setting these option block words defines a box within which your drawing border, title block and the ISOGEN drawing will reside.

2.

Set ISOGEN option 3 to 1 so that you can see the corners of the drawing border box when an isometric is created. Also, set the ISOGEN options block word 35 to define the reserved area for the title block.

9-2


3.

Set ISOGEN options 10 - 13 to create margins from the edge of the box created in Step 1. All of your user-defined border and title block graphics must be drawn within these margins; one or more of them will probably be quite large. You cannot reserve irregularly shaped areas within the drawing box for your border and title block. You must fit them into the rectangular margin areas.

4.

Generate an isometric using the interactive software (see Interactive Isometric Extraction, page 3 - 1 section Interactive Isometric Generation). The iso should be small enough so that only one sheet is generated.

5.

Call up the iso in graphics and plot it with the appropriate drawing size. Plot the area that will contain both your user-defined graphics and the ISOGEN drawing. Do not plot a small strip along the bottom of the drawing (appx. 1/8") since you will probably want to move into that area some ISOGEN-generated text strings that cannot be turned off. You do not have to plot an ISOGEN D size drawing with D size dimensions. You can use ISOGEN switches to make any size drawing you wish. You can then scale the drawing to have any plotted size you like. For this reason, experimentation is usually needed to arrive at a suitable combination of ISOGEN and plotting parameters.

6.

Examine the plot. There must be sufficient space for your user-defined border and title block graphics. Also, the drawing graphics and text size must be suitable for the plot size. Adjust ISOGEN option 14 or options 15 and 16 to adjust the scale of the drawing. Adjust options 4 and 27 to change the text size.

7.

Cycle through Steps 2 through 5 until you are satisfied with the resulting plot. In general, ISOGEN seems to perform better with a larger drawing area than a smaller one (the drawing area is increased with option 14 or options 15 and 16). Try to find a median between providing ISOGEN a large drawing area and scaling down the drawing for plotting purposes. At some point, scaling down a large drawing results in text that is too small. If the text size cannot be increased, then you will either have to plot with a bigger scale (resulting in a larger drawing) or reduce the ISOGEN drawing area (to reduce the amount of scaling needed at plot time).

8.

After completing Steps 1 through 6, create a drawing border in a separate design file. Create a 2D design file for your border and attach the drawing file created above as a reference file. Use the drawing to locate your border and title block.

9.

Use the reference file attachment from the border file and attach the new border to the new seed.

10.

Place the required text nodes in the new seed file for use with the Title Block Tables file.

11.

Turn off the ISOGEN border with ISOGEN word 18.

Creating Seed Files for Extraction 9 - 3

9.2 Creating a Plot Request File __________________________________________________________________________________________________________________________________________________ The plot request file is a special file used by the plotting software when processing a plot job. It contains values for plotting options and, sometimes, a definition of the plot itself. The format of the plot request is standard IPLOT format.

9.2.1 IPLOT Plot Request Files __________________________________________________________________________________________________________________________________________________ An IPLOT plot request file is necessary if you want to plot isometrics using the IPLOT software.

Use the following steps to create an IPLOT plot request file: 1.

Copy your isometric seed file and get into the copy in graphics. Set up view 1 to have all of the parameters that you wish to be active for the plotted drawings (that is, turn off text node display, turn on/off levels to be plotted, etc.). Save this set-up with FILE DESIGN. Determine the coordinates, in working units, of the area to be plotted. These should be the lower left and upper right corners of the fence that would have been used for plotting. Write the coordinates down.

2.

From the command line prompt, key in the following command to create the IPLOT plot request file:

$iplot create "plot parameter filename" -design=design name -queue=queue name -region=[x1, y1, x2, y2] -scale=design units:plotter units -view=#

where: plot parameter filename

plot parameter filename to be generated

design name

is the name of the design file created by copying the seed file in step 1 above.

queue

identifies the plot queue on the plot node.

region

identifies the area to plot. Use the coordinates determined from step 1.

9-4


design units: plotter units

is an option scaling ratio for the plotted area. If you prefer, you may use -XSIZE=x size or -YSIZE=y size instead of the -SCALE= parameter to define the scaling. You may also leave this parameter off if no scaling is needed.

#-

view number

Example 1: iplot create test.i -design=test.dgn -queue=muxque -region=[0,0,17:0,11:8] -view=1 The system creates the file test.i.

Mapping Attributes to the Title Block 10 - 1

10. Mapping Attributes to the Title Block

__________________________________________________________________________________________________________________________________________________

The Title Block Tables Files are used to associate database attribute data and other data with text nodes in an isometric design file. You make this association between attribute data and design file text nodes so the batch iso extraction software can automatically fill out the drawing title block. Intergraph option 34 must be set to 1 before the software will generate the title block data files. You can obtain title block information from several sources using the Title Block Tables File. These sources include database attributes from the line being extracted (for example, piping materials class), data stored within the project control database information (for example, revision block data), from the Notes Table and internally generated information (for example, sheet number). The format of the tables and the table entries in the Title Block Table Files are identical to that of tables and table entries in the iso extraction Defaults file. The format is as follows: The body of the table is preceded by a keyword. Each keyword is followed by a number that defines the number of table entries. The elements of each table entry are separated by commas. The following three tables are used to map attributes to the drawing title block: The text node number can not be greater than 999. Also, the number of text nodes in a seed file can not exceed 250. 1.

Notes Table (Table keyword is SEGMENT_DATA_TABLE) You can use this table to identify the attributes that should be summarized in tabular form on each sheet of a multisheet isometric. Usually, data summarized in this form will be from piping segments, but it may also originate from the Notes Table. When the title block for a particular sheet is filled in, only data from segments extracted to that sheet is placed in the title block.

2.

Drawing Data Table (Table keyword DRAWING_DATA_TABLE) You can use this table to identify attributes from the first piping segment, the largest piping segment, from the Notes Table or from the project control database. Attributes mapped through this table will appear on every sheet of a multisheet isometric.

10 - 2

3.


Sheet Data Table (Table keyword SHEET_DATA_TABLE) You use this table to place the sheet number and number of sheets in each drawing. You can also use this table to append the sheet number onto the drawing number for each sheet, making the drawing number unique for each sheet.


10.1 SEGMENT_DATA_TABLE __________________________________________________________________________________________________________________________________________________ Each sheet of a multisheet iso consists of the piping from one or more segments in the piping model. You can use the SEGMENT_DATA_TABLE to define a summary block of segment information in a drawing title block. The ISOGEN interface uses this table to create an output file containing data for all of the segments that make up the pipeline. Next, ISOGEN creates an output file that identifies which segments appear on each sheet of a multisheet iso. These two files are then used to determine the information that must be summarized on each individual sheet. Example 1: Suppose that for each sheet of an isometric, you want to summarize, in a table, data from all of the piping segments that appear. Here is an example table for a specific sheet: Piping Spec Design Pressure Design Temperature Insulation Type Insulation Thickness

1C0031 150 300 C 6"

1C0031 150 300 D 8"

1C0080 150 600 C 6"

In this example, there are three segments where the data being summarized is different. This does not mean that the sheet contains only three segments, but that there are only three different segments (where the difference is defined only by the attributes in the table). The segment attributes shown in the table above are: Piping Spec Design Pressure Design Temperature Insulation Type Insulation Thickness

Table 12, Table 12, Table 12, Table 12, Table 12,

Column 12 Column 28 Column 29 Column 14 Column 15

The purpose of the SEGMENT_DATA_TABLE is to allow you to define all of the attributes that make up a single column in the title block summary table. Once you have defined these attributes, the batch extraction software determines how many columns of actual data are needed based upon the specific segments that appear on each sheet. You must have one table entry in the SEGMENT_DATA_TABLE for each attribute you want to summarize in the Segment Summary Table. An entry in the table has the following form: TBLNO, ST, SC, SN, OFF, LEN, FLAG, NODE, INC where:

10 - 4


TBLNO

is a table number that ranges from 1 to 9. You can define up to 9 different tables in your title block. For each different table number you should define the attributes and other information that comprise the table definition. For each table number defined, one output file record is generated for each segment in the pipeline. Therefore, if you use two table numbers and a pipeline contains 10 segments, 20 records are generated in the output file. To eliminate trailing zeros from isometric attributes, create an isometric label for the appropriate attributes (temperature, pressure, etc.) then call the isometric label (instead of the table/column) from the title block mapping file.

ST, SC

defines a segment column that will appear in the table. Valid values for ST are 12 and 1.

SN

is a label description library number used to define an attribute or a composite attribute that should appear in the title block table. When SN is specified (as non-zero), ST and SC should be set to 1. If SN is a negative value, the Notes Table is accessed. Text is then extracted from the Notes Table based on the value defined by the absolute value of SN.

OFF

is a byte offset (relative to 0) to the start of the field in the output file record. Set OFF as follows: The minimum offset must be 11. The first 11 bytes of each output record are reserved for the table number and segment occurrence number. Fields from different table numbers must not overlap. For example, data in table number 1 might be mapped to fields 12 through 100, while data in table number 2 might be mapped to fields 101 through 200. If you do overlap fields, the data might not be sorted properly in the title block. Do not map any field to an offset greater than 255.

LEN

is the length of the field in the output record. The offset plus length of any field must not exceed 255.

FLAG

is a special sort flag that indicates that the field is to be considered a sort field for purposes of sorting the data prior to placing it in the title block. Set FLAG to:

1

to specify that the field should be sorted in descending order.

-1

to specify that the field should be sorted in ascending order.

When multiple fields are used for sorting the data, the most important sort field should appear in the notes table prior to the least important.


NODE

is the initial text node number in the summary table for the attribute. The summary information is mapped to a matrix of text nodes in the seed isometric design file. The size of the matrix needed is not known until after the isometric is extracted. Specify here the lowest text node number for an attribute in the table.

INC

is the increment for the text node number. Text node numbers for each item in the attribute summary are determined by taking the base node number and adding a multiple of the increment whenever a new column (or row) of data is added.

Example 2: Define the notes table for the data summarized in Example 11.1. Assume that the seed isometric design file has been created with the following set up: Piping Spec Design Pressure Design Temperature Insulation Type Insulation Thickness

+10 +11 +12

+20 +21 +22

+30 +31 +32

+40 +41 +42

+50 +51 +52

+60 +61 +62

+70 +71 +72

+80 +81 +82

+13 +14

+23 +24

+33 +34

+43 +44

+53 +54

+63 +64

+73 +74

+83 +84

The numbers represent the text nodes that have been placed in the seed design file. Since there are only eight columns of node numbers, at most only eight segments can be summarized in the title block. If there are more than eight different segments on a sheet, some are ignored and not summarized in the title block. The table needed to summarize this information would be: 1, 1, 1, 1, 1,

12, 12, 12, 12, 12,

12, 28, 29, 14, 15,

0, 0, 0, 0, 0,

11, 17, 21, 25, 27,

6, 4, 4, 2, 4,

1, 0, 0, 0, 0,

10, 11, 12, 13, 14,

10 10 10 10 10

!piping spec !design pressure !design temperature !insulation type !insulation thickness

The first entry in the table maps the piping spec to column 12 for a length of 6 bytes. The piping spec field is a sort key that alphabetizes the columns of data in the table so that they appear in alphabetical order by spec name. The beginning node number for spec is 10 and each new column of data has an increment of 10. In this example, the first spec is placed at node 10, the second at 20, the third at 30 and so on. If you put an attribute like segment npd in a table such as the one in Example 2, a typical line could generate a large number of columns or rows in the summary table. A better solution might be to use a different TBLNO for this type of attribute and summarize in a separate table on the drawing. Example 3: Summarize the data shown in Example 2 in one table. Summarize all of the npd’s and line names shown on a sheet in separate tables.

10 - 6


The following notes table would accomplish this: 1, 1, 1, 1, 1, 2, 3,

12, 12, 12, 12, 12, 12, 12,

12, 28, 29, 14, 15, 11, -2,

0, 0, 0, 0, 0, 0, 0,

11, 17, 21, 25, 27, 31, 37,

6, 4, 4, 2, 4, 6, 8,

1, 0, 0, 0, 0, 1, -1,

10, 11, 12, 13, 14, 100, 150,

10 10 10 10 10 1 1

!piping spec !design pressure !design temperature !insulation type !insulation thickness !npd !line id

In this example, the fields defined in tables 2 and 3 do not overlap the fields defined in table 1. If the seed isometric design file contains only text nodes 100, 101, and 102 for npd’s, only the three largest sizes on the sheet are displayed. This happens because FLAG is set to 1 indicating that the npd field is a sort field.


10.2 DRAWING_DATA_TABLE __________________________________________________________________________________________________________________________________________________ You can use the Drawing Data Table to define attributes that should be placed in every drawing sheet title block. Data that you can place in every title block can originate from the first segment of the pipeline processed by the ISOGEN interface, from the largest npd segment of the pipeline, from the Notes Table, from the project control database, or it can be an internally generated attribute. An entry in the drawing data table consists of the following: SOURCE, TBL, COL, NUM, FLAG, NODE where: SOURCE

is the source of the attribute that is to be mapped to the title block. Set the value of SOURCE to one of the following:

TBL, COL

1

if the attribute is from the first segment of the pipeline.

2

if the attribute is from the largest npd segment of the pipeline.

3

if the attribute is from the Project Database.

4

if the attribute is one of the special items as defined in the description of TBL, COL that follows.

5

if the attribute is from the Notes Table accessed with attributes from the first piping segment.

6

if the attribute is from the Notes Table accessed with attributes from the largest piping segment. defines the specific attribute that you want to map to the title block. The exact interpretation of TBL, COL depends upon SOURCE as follows: SOURCE is 1 or 2 TBL, COL is the database table, column pair of the attribute to map. For a listing of the database structure, see Piping Design Database Table Format, page D - 4 . SOURCE is 3 TBL, COL identifies the attribute to retrieve from the Project Control Database. The following index must be used for TBL, COL. Set TBL to 1 for data from the area level of the file (that is, any data which appears in the Revise Iso Area form while in the batch iso environment). Set the value of COL as follows:

10 - 8


COL 1 2-21 22 23 24 25 26 27 90-99

Data Item for TBL = 1 Piping area Model design files Options file Seed isometric file Plot request form Output file directory Iso design file name option Drawing number option User data 1 through 10

Set TBL to 2 for data from the drawing level of the file (that is, any data from the Revise Drawing form while in the batch iso environment). Set the value of COL as follows: COL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 65 90-99

Data Item for TBL = 2 Piping area Primary line id Secondary line id 1 Secondary line id 2 Drawing number Batch reference Iso file name Model status code Model revised date Current extraction date Current extraction number Number of sheets from previous extraction Date MTO neutral file was generated Date MTO was sent for Material Control Current revision number Revision block Revision number Revision block By initials Revision block Chk initials Revision block appv initials Revision block issue date Revision block extraction number Revision block number of sheets Revision block Description Number of Sections User data item 1 through 10

Set TBL to 101 for project description data (as in the project.ddl file). Set the value of COL as follows: COL

Data Item for TBL = 101

2 3 4 5 6

project number project name job number company name plant name


SOURCE is 4 Set the value of COL as follows for special items: COL 1 2 3

Data item for SOURCE=4 Project Database name Mto neutral file name Options file name

SOURCE is 5 or 6 TBL should be 1. COL defines which value to return from an entry in the Notes Table. For more information, refer to Creating a Notes Table, page 11 - 1 . NUM

NUM functions differently depending upon SOURCE as follows: SOURCE is 1 or 2 NUM is a label library number used to define composite database attributes as an alternative to TBL, COL. When NUM is defined COL should be 0. TBL should be set to 1. The label must refer only to segment table 12. SOURCE is 3 NUM defines which revision level to return data from. Flag

Revision level for TBL=2, COL=16-23

0 1 2 3 4 5 6

Current revision Revision prior to the current revision Revision prior to that for FLAG = 1 Revision prior to that for FLAG = 2 Revision prior to that for FLAG = 3 Revision prior to that for FLAG = 4 Revision prior to that for FLAG = 5

If the value of flag is such that the revision that it identifies is less than 0, no output is generated. When the batch run option INCREMENT REVISION NUMBER is in effect, the current revision number is one plus the latest revision number stored in the project database Table 185 Column 17. If the option is not in effect, the current revision number is the latest revision number stored in the project database Table 185 Column 17. SOURCE is 4 NUM must be 0 SOURCE is 5 or 6

10 - 10


NUM is a label library label that, when expanded, becomes the input into the Notes Table. TBL must be 1. Refer to Creating a Notes Table, page 11 - 1 for more information. FLAG

When SOURCE is 1 or 2, you should set FLAG to 1 if you want to inhibit the conversion of code-listed attributes to their text-string equivalents. For other values of SOURCE, FLAG should be set to 0.

NODE

is the text node number to which the attribute should be mapped.

Example 1: 1, 12, 0, 951, 0, 5 Maps the string defined by label number 951 to text node number 5. Label 951 is expanded using attributes from the first piping segment of the pipeline. 3, 2, 91, 0, 0, 97 Maps the first user data field for a drawing to text node 97. 3, 1, 22, 0, 0, 96 Maps the defaults file stored at the area level in the Batch Data File to text node number 96. 4, 0, 3, 0, 0, 95 Maps the options file used for the current extraction to text node number 95. 6, 1, 3, 979, 0, 11 Maps the 3rd output field from a Notes Table record to text node number 11. The Notes Table record key is defined by label library label number 979, which is expanded using attributes from the largest piping segment in the pipeline. Example 2: Mapping Values to Title Blocks

It is possible to map a value that is not stored in the database to the title block of an iso using the Title Block Table, isoc.blk, in conjunction with the Notes Table, isoc.note. When entries contain a source of 5 or 6 in the DRAWING_DATA_TABLE section of the Title Block Table, isoc.blk, as shown below, the system references the Notes Table, isoc.note, for the data to use on the text node of the iso title block. Examples of a Title Block Table isoc.blk and the Notes Table, isoc.note, are shown below. Title Block Table entry: isoc.blk

DRAWING_DATA_TABLE 2 5, 1, 1, 992, 0, 12 5, 1, 1, 982, 0, 15


Notes Table entries: isoc.note

1C0031 2C0032 SS CS

>150# CS >300# CS >Stainless Steel >Carbon Steel

In the example above, the line containing 5, 1, 1, 992, 0, 12 uses label 992. Label 992 is defined as Table 12, Column 12 (piping_materials_class). The system reads Table 12, Column 12 and extracts the data. For instance, the extracted data might be piping_materials_class 1C0031. The system then compares 1C0031 with the Notes Table and prints the corresponding value of 150# CS on text node 12. If the piping materials class value is 2C0032, 300# CS is placed on text node 12. Likewise, the line containing 5, 1, 1, 982, 0, 15 uses label 982. Label 982 is the attribute value defined for the Materials of Construction Class. The system reads the attribute value and extracts it. For instance, the extracted data might be CS. The system then compares CS with the Notes Table and prints the corresponding value, Carbon Steel, on text node 15. If the extracted data is SS, Stainless Steel is placed on text node 15. When there is no match in the Notes Table for a specific piping materials class entry, the error message ’Notes table look-up failed’ is displayed in the .err file.

10 - 12


10.3 SHEET_DATA_TABLE __________________________________________________________________________________________________________________________________________________ You can use the Sheet Data Table to map the sheet number and number of sheets into the drawing title block and to append the sheet number to the drawing number prior to its placement in the title block. A table entry is defined as follows: SOURCE, TBL, COL, FLAG, NODE where: SOURCE

is the data item source. Set the value of SOURCE as follows: SOURCE 0 3

TBL, COL

Attribute source Internally generated attribute Attribute from the Project Database

identifies a data item only when SOURCE is set to 3. (Use TBL=2, COL=5 to specify the drawing number.) For each sheet in the isometric, the sheet number is appended to the data item before it is placed in the title block. If SOURCE is set to 0, TBL and COL must also be set to 0.

FLAG

identifies internally generated attributes. FLAG is also used to append the sheet number to the attribute defined by TBL, COL. Set the value of FLAG as follows: FLAG

Data item

1 2 -1 -2

Sheet number when SOURCE = 0 Number of sheets when SOURCE = 0 Append sheet num to attribute defined by TBL, COL Append sheet num prefixed by a "-"

Sheet number and number of sheets can also be located in a title block using the MOVABLE_TEXT table in the options file. However, that method will not result in correct sheet numbers when a multi-section isometric is extracted. NODE

is the text node number to which the attribute should be attached.

Example 1: Develop the table to map sheet number and number of sheets to the title block. Show the entry needed to append the sheet number to the drawing number for each sheet.


The table needed to accomplish this would be: 0, 0, 3,

0, 0, 2,

0, 0, 5,

1, 2, -1,

160 161 200

!sheet number !number of sheets !drawing number

10 - 14


Creating a Notes Table 11 - 1

11. Creating a Notes Table

__________________________________________________________________________________________________________________________________________________

This section describes how to create a Notes Table. A Notes Table is a user-defined table that you can use to map nondatabase attributes into an iso drawing border during batch iso extraction. The table consists of one input together with a variable number of outputs. The input to the table is either a fixed string, such as "PROJECT DATA", or is derived from segment level database attributes. During a batch run, a table input is determined by expanding a label library number that you define in the Title Block Map (refer to DRAWING_DATA_TABLE, page 10 - 7 and SEGMENT_DATA_TABLE, page 10 - 3 for more information). The label is used as the key or index into the notes table. The table is searched until a match is found with the key. When a match is found, one of the table outputs is mapped to a text node. You define which output is mapped to which text node in the Title Block Map. Table Format The Notes Table is an ascii data file you create with the text editor. In the file one record or line is an entry. The number of table entries is unlimited. A single entry is limited, however, to 256 bytes or characters. The key and table outputs are separated from each other with the greater than (>) character. For more information, refer to DRAWING_DATA_TABLE, page 10 - 7 . The format of a table entry is: TBL INPUT > OUTPUT1> OUTPUT2> ... >OUTPUTn Example 1: PROJECT DATA > PROJECT ABC> ANYWHERE, USA> REFINERY EXPANSION> 6368-20 The key for this table entry is the fixed string "PROJECT DATA". The outputs are the strings "PROJECT ABC", "ANYWHERE, USA", "REFINERY EXPANSION", and "6368-10". U50-A10> RED The input for this table entry is U50-A10 (unit 50 - area 10). The only output is the string "RED".

11 - 2


11.1 Using the isoc.note File __________________________________________________________________________________________________________________________________________________ The notes file, isoc.note, in conjunction with the title block tables file, isoc.blk allows you to map a value, not stored in the database, to the title block. The files isoc.note and isoc.blk are delivered examples of a Notes file and a Title Block Tables file. Example Title Block Table entry:

Example DRAWING_DATA_TABLE entry: 2 5, 1, 1, 992, 0, 12 5, 1, 1, 982, 0, 15

Example Notes Table entry:

1C0031 2C0032 SS CS

>150# CS >300# CS >Stainless Steel >Carbon Steel

Entries in the DRAWING_DATA_TABLE section of the Title Block Tables file that have a source of 5 or 6 cause the software to search the Notes Table for information to output onto a text node in the iso title block. For more information, see DRAWING_DATA_TABLE, page 10 - 7 . In the previous example, line 5, 1, 1, 992, 0, 12 uses label 992 (table 12, column 12; piping material class) to define search/access criteria that will be used to search line segments in the piping model. The output of the piping model segment search is used as input to the Notes Table (see previous example). If the value returned from the search was piping material class 1C0031, it would be used as input into the Notes Table. The resulting output of piping material class 1C0031 would be 150# CS. The software would then place the output value, 150# CS, on text node 12. If the piping material class had been 2C0032, the resulting text on text node 12 would be 300# CS. Any other piping material class found as a result of the search would output an error Notes table look-up failed. This is because the input value is not in the Notes Table. The second line in the Title Block Table entry (5, 1, 1, 982, 0, 15) will write a note to text node 15 on the iso if the Materials of Construction Class attribute value stored with the line segment is SS or CS. If SS is returned from the search of the previously mentioned Title Block Table Entry, "Stainless Steel" would be placed on text node 15. If CS was returned, "Carbon Steel" would be placed on text node 15.

The MTO Neutral File Record Map 12 - 1

12. The MTO Neutral File Record Map

__________________________________________________________________________________________________________________________________________________

The MTO neutral file record map consists of a set of tables that is used to format records in the MTO neutral file. A record is generated in the MTO neutral file for each component that is MTO-able in the extracted pipeline. The neutral file record length can be either the standard 255 byte or the expanded 1024 byte depending on the setting of Intergraph option 64. The format of a record in the neutral file varies depending on the type of component that generates the record. The following record types may exist in a neutral file: Commodity item record Pipe record Engineered item record Instrument item record Pipe support record Implied bolts record Implied gasket record Implied weld record Generated item record While each of these record types can have several fields that contain the same data, each can also contain additional data that is unique to its type (for example, number of bolts in the bolt record). The neutral file map tables tell the iso extraction software which design database attributes to place in each record and where to place them. The map is composed of four tables: 1.

Common data table (Table keyword is COMMON_RECORD_DATA) The common data table defines attributes that are to be placed into each record regardless of the type of the record.

2.

Component data table (Keyword is COMPONENT_ATTRIBUTES) The component data table defines the attributes that are to be placed into commodity item, pipe, specialty item, instrument and support record types.

12 - 2

3.


Implied item table (Keyword is IMPLIED_ITEMS) The implied item table defines the attributes that are to be placed into bolt, gasket and weld type records.

4.

Generated item table (keyword is GENERATED_ITEMS) The generated item table defines the attributes that are to be placed into the records of items that generated through the reference database.

The tables themselves are similar to options file tables in that the body of a table is preceded by a keyword that identifies the table. The keyword is followed by a number that indicates the number of table entries. One row or line constitutes a table entry. One table entry defines a neutral file record field. Each table is discussed in detail in this section.

12.1 COMMON_RECORD_DATA __________________________________________________________________________________________________________________________________________________ Fields defined in this table appear in every neutral file record. An entry in this table has the following form: TABLE, COL, OFFSET, LENGTH, FLAG Where: TABLE, COL

is the table, column specification for a segment level attribute that is to be mapped into the record or is set as shown in the index below for a special data item. TABLE _______

COL _____

Special data item mapped to the record _____________________________________

-1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1

1 2 3 4 5 6 7 8 9 10 11 12

-1

13

-1

14

-1

15

component occurrence number segment occurrence number commodity code commodity item material description record type (required)- see note below RESERVED FOR LATER USE file units - see note below specialty item material description instrument item material description pipe support item material description generated item material description dry component center of gravity X coordinate reported in sub-units dry component center of gravity Y coordinate reported in sub-units dry component center of gravity Z coordinate reported in sub-units wet component center of gravity X coordinate reported in sub-units


-1

16

-1

17

-1 -1 -1

18 19 20

wet component center of gravity Y coordinate reported in sub-units wet component center of gravity Z coordinate reported in sub-units model name area name partition number

The commodity code can be mapped through this table or through the component level tables. It should be mapped here when commodity codes are size dependent.

The record type is a simple character string as follows: COMP - for commodity items PIPE - for pipe ENGR - for specialty items INST - for instruments SUPP - for pipe supports GASK - for gaskets BOLT - for bolts WELD - for welds GENR - for generated items File units is a simple character string as follows: ENGL - for English units MIX - for mixed units METR - for all Metric units can also use COL=-2 to obtain the line ID rather than the line name.

Generated items consist of chain wheel operators and items implied through the reference database. OFFSET

Is the offset (relative to 0) in the record for the start of the field.

LENGTH

Is the length of the data item’s field. The sum of offset + length must not exceed the length of the output record (255 characters).

FLAG

Is a special flag that is normally 0 but is set to 1 to inhibit conversion of code-listed attributes to their ASCII string equivalents. When FLAG is set to 1, the code-list number will be placed in the record.

Example: 12, 12, 14, 6, 0

maps the piping materials class into EVERY MTO neutral file record starting at output field 15 (offset 14) for 6 bytes.

12 - 4


12, -2, 4, 10, 0

maps the line id (defined in the defaults file) into EVERY MTO record starting at output field 5 for 10 bytes.

-1, 1, 20, 8, 0

maps the component database occurrence number into EVERY record starting at output field 21 for 8 bytes. Note that for implied materials this is the occurrence number of the GENERATING component.

-1, 5, 0, 4, 0

maps the record type of each record into output field 1 for 4 bytes.

12.2 COMPONENT_ATTRIBUTES __________________________________________________________________________________________________________________________________________________ Fields defined by this table appear in component, specialty item, pipe, instrument and pipe support records. An entry in the table has the following form: CT, CC, ET, EC, PT, PC, IT, IC, ST, SC, CPI, OFFSET, LENGTH, FLAG Where: CT, CC

defines a table, column specification for the case when the current item that is generating a neutral file record is a component. Valid values for CT are 0, 12 and 34.

ET, EC

defines a table, column specification for the case when the current item is a specialty item. Valid values for ET are 0, 12 and 34.

PT, PC

defines a table, column specification for the case when the current item is a pipe. Valid values for PT are 0, 12, and 50.

IT, IC

defines a table, column specification for the case when the current item is an instrument. Valid values for IT are 0, 12, 67.

ST, SC

defines a table, column specification for the case when the current item is a pipe support. Valid values for ST are 0, 12, and 80. When the MTO neutral file record is being generated for an item then its type is determined and one of the entity, attribute pairs above is chosen for purposes of fetching an attribute from the database. Not all pairs in the above set need to be defined. If a component data table entry should apply only to one type of item, set the entity, attribute pairs for other types to zeroes.

CPI

is a connect point identifier. It is used to access connect point attributes by connect point color (green or red) rather than by attribute number for the COMPONENT_ATTRIBUTES table. CPI is also used by the IMPLIED_ITEMS table when set to 1 to indicate that the attribute will be retrieved from the connect point of the item generating the implied material.


When set to 1, CPI is used by the IMPLIED_ITEMS table to indicate that the attribute will be retrieved from the connect point of the item generating the implied material. When CPI is set (nonzero), CT, ET, PT, IT, and ST should be set to zero and CC, EC, PC, and IC should be set to one of the values shown in the following index. CPI ____

Means _ _____

1 2


Index ______


1 2 3 4 5 6 7 8 9 10 11 12 13

nominal piping diameter outside diameter end preparation schedule thickness pressure rating stress analysis node number face-to-center distance/pipe length weld number weld type gasket gap stress intensification factor head loss factor inspection number

OFFSET

is the offset into the neutral file record to the start of the field.

LENGTH

is the length, in bytes, of the field.

FLAG

Is a special flag that is normally 0 but is set to 1 to inhibit conversion of code-listed attributes to their ASCII string equivalents. When FLAG is set to 1, the code-list number will be placed in the record. If lap joint flanges are mapped to ISOGEN record number 106 to generate both the stub and flange in the ISOGEN material list, a separate record generated is in the MTO neutral file for the stub as well (refer to the section The PDS-toISOGEN Symbol Map, page 13 - 1 .) The MTO record for the stub is generated by overlaying attributes from the reference database entry for the stub onto the database record for the flange and then applying the COMPONENT_ATTRIBUTES table to this temporary occurrence.

Example 1: 34, 3, 34, 3, 50, 3, 67, 3, 80, 4, 0, 53, 6, 0 This table entry maps the item name attribute for all component types into the neutral file record starting at column 53 for 6 bytes.

12 - 6


34, 4, 0, 0, 50, 4, 0, 0, 0, 0, 0, 60, 6, 0 This table entry maps the new item name attribute for component types of COMPONENT and PIPE. Nothing is generated in the record for SPECIALTY ITEMS, INSTRUMENTS or PIPE SUPPORTS by this table entry. 0, 1, 0, 1, 0, 1, 0, 1, 0, 0, 1, 66, 8, 0 This table entry maps the GREEN nominal pipe size (also referred to as size 1) into the neutral file record. Since pipe supports do not have connect point properties, no number is specified for them in the entry. 0, 1, 0, 1, 0, 1, 0, 1, 0, 0, 2, 74, 8, 0 This table entry maps the RED nominal pipe size (also referred to as size 2) into the neutral file record. 0, 4, 0, 4, 0, 4, 0, 4, 0, 0, 1, 94, 6, 0 This table entry maps the GREEN schedule (schedule 1) into the neutral file record. 12, 14, 12, 14, 12, 14, 12, 14, 0, 0, 0, 118, 2, 0 This table entry maps the insulation purpose attribute from the segment into the neutral file record for all items except pipe supports. 12, 27, 12, 27, 12, 27, 12, 27, 0, 0, 0, 126, 2, 1 This entry maps the paint code CODE-LIST VALUE from the segment into the MTO neutral file record. The code-list value is put in the record rather than the attribute itself because FLAG is set to 1 and the attribute being mapped is code-listed. Example 2: The following is an example of how to set the COMPONENT_ATTRIBUTES to extract item inspection number and inspection numbers for item connect point one. 34, 121, 34, 121, 50, 59, 67, 128, 80, 38, 0, 96, 4, 0 !item insp key 34, 122, 34, 122, 50, 60, 67, 129, 0, 0, 0, 100, 4, 0 !cp1 insp key

12.3 IMPLIED_ITEMS __________________________________________________________________________________________________________________________________________________ Fields defined in this table appear in neutral file records for bolts, gaskets and welds. The implied items table provides a means to map attributes that are: from the component that caused the item to be generated (for example: flange pressure rating)

from the spec entry for the implied item (for example: for the commodity code)


from data calculated when the item is generated (for example: bolt length) An entry in this table has the following form: TYPE, CT, CC, PT, PC, IT, IC, ST, SC, CPF, ITEM, OFFSET, LENGTH,

FLAG

Where: TYPE

defines the type of implied component that the table entry is to apply to.

TYPE ______

TABLE ENTRY APPLIES TO ____________________________

1 2 3 4

Gaskets only Bolts only Welds only All of the above items

CT, CC

defines a table, column specification from a generating component that is to be mapped when the generating component is a COMPONENT or SPECIALTY ITEM. Valid values for CT are 0, 12 and 34.

PT, PC


IT, IC

defines a table, column specification from a generating component that is to be mapped when the generating component is an instrument. Valid values for IT are 0, 12 and 67.

ST, SC

defines a table, column specification that is to be mapped when the attribute is taken from the reference database entry for the implied item. The only valid values for ST are 202 and 0.

CPF

is a connect point flag. When this item is set to 1 it indicates that the attribute will be retrieved from the connect point of the item generating the implied material. When set other than zero, CT, PT and IT should be set to 0. CC, PC and IC should be set to one of the values shown in the following Connect Point Attributes index.

Index ______


1 2 3 4 5 6 7 8 9

nominal piping diameter outside diameter end preparation schedule thickness pressure rating stress analysis node number face-to-center distance/pipe length weld number weld type

12 - 8


10 11 12 13

ITEM

gasket gap stress intensification factor head loss factor inspection number

When this value is other than zero, it indicates that either the attribute to be mapped is data that was generated along with the implied item, or the attribute is to be obtained from the spec. Values for item are dependent on the implied item type as shown below. Item type _________

ITEM ______


ALL

-1

Use ST,SC to obtain the attribute from the spec database

BOLT

1 2

Number of bolts Bolt length in Project Units English for English Project Metric for Metric or Mixed Project Bolt diameter English for English Project Metric for Metric or Mixed Project Number of nuts Bolt diameter in English Units Bolt length in English Units Bolt weight in English Units (pounds) Bolt weight in English Units (kilograms)

3

4 5 6 7 8 GASKET WELD

0 1 2 3 4

Weld ID number Weld Type Material A Material B

OFFSET


LENGTH


FLAG

is a special flag used to inhibit the conversion of code-listed attributes to the ASCII string equivalents. You cannot map attributes for a weld from the reference database into the neutral file record. However, you can use a component TYPE of 4 (for ALL implied items) when mapping attributes from the spec for bolts and gaskets. In the case of a weld the field will be left blank.

Two welds may be generated on olet-like components. The first weld, which corresponds to the weld that attaches the olet to the header, is given the size from the header pipe as a safe estimate of the weld size.


The second weld, which corresponds to the point where the branch pipe attaches to the olet, is given the branch pipe size.

No welds are generated at branch welds. Branch welds are defined as those components that are mapped to the ISOGEN symbol TESO. The reason for this is that the component itself represents a weld and it is generated in the neutral file.

One weld is generated at a reinforcing pad. The weld represents the attachment of the pad to the header pipe. The reinforcing pad component represents the attachment of the branch pipe to the header.

Example: This table entry maps the gasket size into the neutral file record starting at output field 67 for 8 bytes. 1, 0, 1, 0, 1, 0, 1, 0, 0, 1, 0, 66, 8, 0 This table entry maps the item name from the reference database for a bolt into the neutral file record. 2, 0, 0, 0, 0, 0, 0, 202, 3, 0, -1, 53, 6, 0 This table entry maps the bolt length into the neutral file record. 2, 0, 0, 0, 0, 0, 0, 0, 0, 0, 2, 127, 8, 0 This table entry maps the inspection number for welds, bolts and gaskets into the MTO neutral file record. 4, 0, 13, 0, 13, 0, 13, 0, 0, 1, 0, 51, 4, 0

12.4 GENERATED_ITEMS __________________________________________________________________________________________________________________________________________________ Fields defined in this table appear in neutral file records for items generated through the reference database and for chain wheel operators. The generated items table provides a means to map attributes that are: from the component that caused the item to be generated

from the reference database entry for the implied item (for example: for the commodity code)

12 - 10


An entry in this table has the following form: CT, CC, ET, EC, PT, PC, IT, IC, ST, SC, CPI, ITEM, OFFSET, LENGTH, FLAG Where: CT, CC

defines a table, column specification from a generating component that is to be mapped when the generating component is a COMPONENT. Valid values for CT are 0, 12 and 34.

ET, EC

defines a table, column specification from a generating component that is to be mapped when the generating component is a SPECIALTY ITEM. Valid values for ET are 0, 12 and 34.

PT, PC


IT, IC

defines a table, column specification from a generating component that is to be mapped when the generating component is an instrument. Valid values for IT are 0, 12 and 67.

ST, SC

defines a table, column specification from a generating component that is to be mapped when the generating component is a pipe support. Valid values for ST are 0, 12 and 80.

CPI

is a connect point identifier. It is used to access connect point attributes by connect point color (green or red) rather than by attribute number for the COMPONENT_ATTRIBUTES table. When set to 1, CPI is used by the IMPLIED_ITEMS table to indicate that the attribute will be retrieved from the connect point of the item generating the implied material. When CPI is set (nonzero), CT, ET, PT, IT, and ST should be set to zero and CC, EC, PC, and IC should be set to one of the values shown in the following index. CPI ____

Means _ _____

1 2


Index ______


1 2 3 4 5 6 7 8 9 10

nominal piping diameter outside diameter end preparation schedule thickness pressure rating stress analysis node number face-to-center distance/pipe length weld number weld type gasket gap


11 12 13

ITEM

stress intensification factor head loss factor inspection number

When this value is set to 1 it indicates that the attribute to be mapped is data from the reference database. The value for CC, EC, PC, IC, and SC should be set according to the table shown below when ITEM is set to 1.

Attr. _____


1 2

Generated item commodity code Generated item quantity

OFFSET


LENGTH


FLAG

is a special flag used to inhibit the conversion of code-listed attributes to the ASCII string equivalents.

Example: 34, 3, 34, 3, 50, 3, 67, 3, 80, 4, 0, 0, 53, 6, 0 This entry maps the item name of the component that generates some implied material into the MTO neutral file record at offset 53 for 6 bytes. 0, 2, 0, 2, 0, 2, 0, 2, 0, 2, 0, 2, 75, 8, 0 This entry maps the generated item quantity into the MTO neutral file record at offset 75 for 8 bytes. In the case of a chain wheel operator, this entry corresponds to the length of chain.

12 - 12


The PDS-to-ISOGEN Symbol Map

13 - 1

13. The PDS-to-ISOGEN Symbol Map

__________________________________________________________________________________________________________________________________________________

You can use the PDS-to-ISOGEN symbol map table to tell the ISOGEN interface software which ISOGEN graphics symbol to use for a specific PDS component when it generates the Isometric drawing. The table is composed of 9 columns of data that are position-dependent (that is, the data must appear in specific columns in the table). You can add comments to the table by placing an an exclamation point (!) in column 1. A table entry consists of one row of data. The format for a table entry is as follows: PDS Item name:

Columns 2-7, left justified

ISOGEN symbol name:


ISOGEN record number:

Columns 14-16, right justified

Number of connect points:


Tap name:


Tap record number:


PDS operator name:


end prep low:


end prep high:


13.1 The PDS Item Name __________________________________________________________________________________________________________________________________________________ The PDS item name is the primary index into the table. Each PDS item that exists in a pipeline must have an entry for it in this table. As each component is processed, the table is searched for a corresponding table entry or entries.

13.2 The ISOGEN Symbol Name __________________________________________________________________________________________________________________________________________________ The ISOGEN symbol name is the primary output from the symbol map table. All of the ISOGEN symbols available with ISOGEN are shown in Appendix B. Look especially at the notes at the end of the appendix. The symbol names are generally four characters in length. The first two characters identify the type of symbol and the last two identify the end preparation. For many symbols, the end prep characters are double asterisks (**). The ** indicate that the symbol may end in one of the following sets of characters:

13 - 2


BW - indicating buttweld ends FL - indicating flanged ends SC - indicating threaded ends SW - indicating socket weld ends CP - indicating compression ends PL - indicating plain ends You can carry the variable end prep notation into the symbol map by substituting the characters XX for the characters **. For example, the ISOGEN symbol name for a ball valve is BV** and the table entry would be BVXX. When a line is extracted, the XX is converted to one of the end prep codes shown above based on the end prep of the component in the model. When you map a PDS component to an ISOGEN component, you must be sure that the connect point skeletons (that is, configuration or geometrical arrangement of the connect points) are the same. You cannot, for example, map a gate valve (whose connect points lie on a straight line) to an elbow (whose connect points define a 90-degree change-of-direction). The basic connect point skeletons handled by ISOGEN are: end point component (plug, blind flange)

straight-through component (gate valve, flange)

offset component (eccentric reducer)

return component (u bend)

change-of-direction component (elbow, angle valve)

single branch component (tee, olet, 3-way valve)

double branch component (cross, 4-way valve) The change-of-direction components for elbows are not restricted to 90-degree changes of direction. Other change-of-direction components, such as 2-way valves, are restricted. The tee components TESO and TEXX can have variable angle changes of direction. Other branch components, such as 3-way valves, must have 90degree changes in direction.

13.3 The ISOGEN Record Number __________________________________________________________________________________________________________________________________________________ Another primary output from the symbol map table is the ISOGEN record number. It is critical that the ISOGEN record match the component type identified by the symbol name. ISOGEN record numbers are defined in Appendix B.


13 - 3

The symbols in Appendix B are grouped by component type. The component type is identified at the top of the first page of each group of symbols. For example, a CV** is an instrument while a VG** is a valve. Appendix B, Record Identification Numbers, shows that the record number for an instrument In Leg is 90. The record number for a valve is 130. The PDS symbol for a lap joint flange represents two components: the flange ring and the stub. You can generate either one or two components in the isometric when you extract the line. If the ISOGEN record number for the lap joint is set to 105, only one component (one entry in the BOM) is generated. If the ISOGEN record number is set to 106, the ISOGEN interface automatically generates a component representing the stub. In this case, you must have an entry in the reference database for the stub. The spec access data for the stub is identical to that for the flange except that the option code is that of the flange plus 5000.

13.4 Number of Connect Points __________________________________________________________________________________________________________________________________________________ Another table output is the number of connect points for the component. This number does not include taps that the symbol may have. It is used both for identifying closure components (plugs, caps, blinds) and for processing tapped components. It is most important that this number be correct for components that may be tapped. The number of connect points is also used to distinguish tee type components (which have three connect points) from branch weld type components (which have two connect points). The number of connect points must be correct for these types of components. Incorrect values will cause incorrect entries in the bill-of-material and/or cut pipe report.

13.5 Tapped Component Name __________________________________________________________________________________________________________________________________________________ The tapped component name is used in special situations. When it is used, the ISOGEN symbol key is taken from this field, rather than the ISOGEN symbol key field.

13.5.1 Tapped elbows __________________________________________________________________________________________________________________________________________________ An elbow is one of the components that ISOGEN considers special. Because it is special, you may not redefine it to add tap points as you can with most other symbols. This results in the need for special handling of tapped elbows. Symbol keys exist for elbows that have a single tap (see Appendix B). For an elbow that is tapped in the model, the symbol key that is passed to ISOGEN is taken from the tapped component name field of the table. Since there are no symbol keys for elbows with more than one tap, you will not be able to extract a doubly tapped elbow.

13 - 4


13.5.2 Olets attached to fittings __________________________________________________________________________________________________________________________________________________ Normally, olet type components are used as branch or tee-type components. However, sometimes an olet is attached to a fitting such as a reducer. ISOGEN does not allow the normal olet type fittings to be used in this case and so you must match an olet attached to a component to a different symbol (you must use one of the coupling components). In this situation, connect point 1 of the olet will be attached to a tap. Whenever an olet is found to be connected to a tap, then the symbol key that is passed to ISOGEN is taken from the tapped component name field (rather than the ISOGEN symbol name field).

13.6 Tapped component record number __________________________________________________________________________________________________________________________________________________ The tapped component record number corresponds to the tapped component name just as the ISOGEN record number corresponds to the ISOGEN symbol name. For a tapped elbow, the record number changes from 35 to 70. For the olet attached to a component, the record number changes from 40 to 126. Example 1: Show the required ISOGEN table entries needed to map socket weld GAT valves to the ISOGEN symbol VTSW, flanged GAT valves with the operator OP_100 to the symbol VTFL and all other GAT valves to the symbol VV**. PDS NAME _______

ISG NAME _______

ISG _REC ____

NO CP ___

GAT GAT GAT

VTFL VTSW VVXX

130 130 130

2 2 2

TAP _NAME ______

TAP _REC ____

PDS OPER ______

END LOW _____

END HIGH ______

OP_100

1 400

199 429

The table entries must be defined in the same order as shown above.

13.7 PDS Valve Operator Name __________________________________________________________________________________________________________________________________________________ The PDS valve operator name is an optional table input. This input is used when it is defined in the model and when it is defined in this table. When a component has a valve operator, the valve operator name from the model is compared to the valve operator name in the table (if it is defined). If they are the same, the table entry is checked further. If they are not the same, the table entry is rejected. If the valve operator is not defined in the table, then it is not considered in the table lookup.


13 - 5

13.8 End Prep Low and End Prep High __________________________________________________________________________________________________________________________________________________ The end prep low and end prep high table entries define an end prep range, a range of end preparation values, which makes component end prep an optional table input. If the end prep range is defined, the component’s end prep is checked to see whether or not it falls within the range defined by end prep low and high. If it does fall within the range, a match has occurred and the table entry is accepted. If it does not, the table entry is rejected. If no range is defined, the components end prep is not considered in the table lookup.

13.9 Order of Table Entries __________________________________________________________________________________________________________________________________________________ Due to the manner in which the table lookup is performed, it is necessary to put the most restrictive table entries prior to the least restrictive. Entries should be in the following order in the table: 1.

Entries with PDS name, operator name and end prep range.

2.

Entries with PDS name and either valve operator name or end prep range.

3.

Entries with only PDS name and neither valve operator or end prep range.

When table entries are placed in the above order, the software can choose the proper table entry, for each case.

13 - 6


The Valve / Operator Table 14 - 1

14. The Valve / Operator Table

__________________________________________________________________________________________________________________________________________________

The valve / operator table is used to map a PDS valve and valve operator to an ISOGEN symbol different from the one mapped by the valve item name alone. This enables you to take better advantage of the variety of valve symbols that are defined within ISOGEN. It also gives you more flexibility in how you map PDS symbols to user-defined ISOGEN symbols. A valve / operator table is an ASCII file created with the editor. The format of the table is as follows:

m,n ’OPER1’, ’OPER2’, . . . ’OPERm’,

’VALV1’, ’SYM11’, ’SYM12’, . . . ’SYMm1’,

’VALV2’, ’SYM12’, ’SYM22’, . . . ’SYMm2’,

... ... ...

’VALVn’, ’SYM1n’, ’SYM2n’, . . . ’SYMmn’

Where: m-

is the number of rows in the table or the number of operators.

n-

is the number of columns in the table or the number of valves.

’VALVp’-

is the pth column heading in the table where p is less than or equal to n.

’OPERq’-

is the qth row heading in the table where q is less than or equal to m.

’SYMpq’-

is the table entry corresponding to VALVp and OPERq.

Example 1: Develop an example valve / operator table.

4, 2 ’OP_3’, ’OP_5’, ’OP_9’, ’OP_11’,

’GATR’, ’VTXX’, ’VKXX’, ’VSXX’, ’VGXX’,

’GAT’, ’VVXX’, ’VDXX’, ’VNXX’, ’VPXX’

You do not need to define every table entry with a value for SYMpq. If VALVp and OPERq should not map to a new symbol, make the table entry a blank (’’).

14 - 2


Every entry in the table, except for m and n, must be surrounded by single quotes and separated by commas. Otherwise, an error will occur when the table is read in.

Each valve defined in the VALOPR table must still be defined in the PDS to ISOGEN symbol map. When a valve and operator map to a new symbol in the VALOPR table, the new symbol must have the same ISOGEN record number as the one defined for the valve in the PDS-to-ISOGEN symbol map. For example, you can map a PDS symbol named GLOR to an ISOGEN symbol named VVXX with an ISOGEN record number of 130. However, you can not map the GLOR with an operator symbol of OP_3 to the ISOGEN symbol CVXX, because CVXX is an instrument with an ISOGEN record number of 90.

Intergraph option 31 must be enabled in order for the VALOPR table to be accessed.

The capability provided by this table is similar to that provided through the PDS to ISOGEN symbol map. If you are mapping valves and valve operators to ISOGEN symbols, then using the VALOPR table is much more efficient than having multiple records in the PDS to ISOGEN symbol map. If, however, you are utilizing the end prep range in the symbol map, you should also use the PDS operator name which is input in the symbol map to map valves and valve operators. The reason for this is that references to the VALOPR table overlay references to the PDS to ISOGEN symbol map. That is, VALOPR table access occurs subsequent to the lookup in the PDS to ISOGEN symbol map.

Repeatability 15 - 1

15. Repeatability

__________________________________________________________________________________________________________________________________________________

ISOGEN’s Repeatability facility allows isometric drawings to be re-extracted. When a drawing is re-extracted, its repeating data is recalled for purposes of extracting the isometric after modifications have been made in the piping model. Repeating data includes: The Iso’s Traversal Start point - (saved to the project database) The Extracted Item’s Iso Sheet Number - (saved to the design database) The extracted Item’s Piecemark Number Repeatability can be enabled and disabled via the Schedule Batch Job form.

Repeatability - Related Information The following is a list of related elements within the ISOGEN software that may be manipulated when using the repeatability feature. Related ISOGEN Options (Appendix B) 38, 108, 109 Related Intergraph Options (Section 7) 4, 68 Related Options File Material (Section 7) NONE Related ISOGEN ATEXT Records (Appendix B) NONE

15 - 2


15.1 Repeatability Restrictions and Limitations __________________________________________________________________________________________________________________________________________________ The following is a list of restrictions, limitations and rules that must be followed to ensure success when using the repeatability facility. Since there is only one place in the piping design file for sheet and spool numbers, repeatability will only be supported for one type of isometric. Split points placed in piping will be ignored during re-extraction. Implied items are not saved in the database and have no record kept that identifies the sheet to which they apply. Therefore, implied items will always be re-extracted on the same sheet as the item which implied them. The ISOGEN software will decide if a sheet will break at a flange. All bolts and gaskets for the flange will be on the same sheet as the flange.

The repeatability facility should not be used if the design is not stable or if extensive changes are being made to a pipeline. If extensive revisions are made to a line and repeatability is used, the result may be a sheet that contains too much information to decipher. If this situation occurs, it may be necessary to disable repeatability and extract the drawing normally so that it can be repaginated. Commands that maintain the old database record are preferred during piping design after the option to use repeating isometrics has been used. Delete Component deletes the database record, and there is no way of knowing the sheet to which it belongs. This is especially true if the item prior to it is on sheet 1, and the item after it is on sheet 2. If you plan on re-extracting an isometric drawing, it must first be extracted with ISOGEN option 108 set to 1 or 2. Once set, this option will not allow pipe splits. When a line is re-extracted, items with a sheet number of 0 will be placed on the same sheet as the item just prior to it. When a line is re-extracted, items that were added before the previous traversal start point will be placed on sheet one. It will not be possible for a multi-sheet iso to contain only disconnected pipelines. For example, if sheet 1 has two notes CONT ON DRG 2, drawing 2 will connect these ends. If an entire sheet is deleted, the sheet numbering will be incorrect when re-extracting a drawing. For example, the initial extraction generates three sheets. A redesign is done and the second sheet is deleted. When this line is re-extracted, it will produce two sheets since blank sheets can not be output.


New spool numbers will not be generated when additional piping is added to the drawing. Since new spool numbers are not identified by ISOGEN, the spool number in the design database will not be updated when extracting with existing sheets.

15.2 Extraction Information in the Database __________________________________________________________________________________________________________________________________________________ Extraction information, depending on its classification, is written to either the project or design database.

Extraction Information in the Project Database Re-extraction information saved to the project database includes the original start traversal point, section number, entity, component occurrence and segment occurrence numbers. The project database table pdtable_189 contains re-extraction information. The following is the format for the table, pdtable_189.

# Isometric Drawing Re-Extraction Data table number = 189 , number of columns = 8 1 2 3 4 5 6 7 8

, , , , , , , ,

drawing_indx_no , integer section_no , short start_traversal_X , integer start_traversal_Y , integer start_traversal_Z , integer start_entity , short start_comp_occ, integer start_seg_occ , integer

Extraction Information in the Design Database When the repeatability is used and the option Save Sheet Extraction Data has been set, existing columns in the design database will be updated in tables 34, 50, 67, and 80. These columns include:

iso_dwg_index_no , integer isometric_sheet_no , character(2) piece_mark_no , character(10)

Where: iso_drawing_index_no isometric_sheet_number

will be the number in table 185 column 1 of the project database. will be the number of the sheet on which the item appears.

15 - 4


piece_mark_no

will be the number of the spool on which the item appears.

When a component belongs to a spool that starts on a different sheet, the piece_mark_no value is reported as a three digit number in the format: xyy. Where x is the iso sheet number on which the spool starts and yy is the component’s spool number (on the x sheet). Only shop items can receive piece mark numbers. All field items are assigned a piece_mark_no of 0.

15.3 Determining the Traversal Start Point __________________________________________________________________________________________________________________________________________________ When using the repeatability function, the ISOGEN software will determine the traversal start point for the extraction. In order of highest priority, the following is a list of rules for determining a traversal point. 1.

Compare the start_entity and start_comp_occ with each item that has been determined to be an end point. If a match occurs, use this as the start point. — End point marked as -1, or -2 for a cap, is a valid start point. — End points marked as -3 for pipe support are not considered as a valid start point. Refer to Section 4: Design File Data Sorted by Topo, page 6 - 15 for more information.

2.

The original start component is not an endpoint. Compare the start_seg_occ with each item that has been determined to be an end point. — If one end matches, use this end point as start point. — If two ends match, pick the end that is the closest to the last traversal start point.

3.

The original start component and segment occurrence are not considered endpoints. The last start point component exists, but it is no longer an end point. Choose the end point that is closest to the original start component. Intergraph option switch 68 can be used to stop the extraction process if the original start item can not be used. The ISOGEN software will generate informational-type messages that show the decision process that lead to selecting a traversal start point.

15.4 Determining Sheet Split Points __________________________________________________________________________________________________________________________________________________ A sheet split location is determined by comparing the current isometric_sheet_no (sheet number) with the previous item sheet number (excluding sheet 0). Split point location is saved and output after the .idf file has completed and all split locations have been determined.


Sheet split locations will be determined using the following rules: Sheet numbers that are 0 will not be considered for sheet split records. Unless otherwise stated, they will not be considered as a sheet change. When a component is processed and that component has a sheet number different from previously processed components, a sheet split record is created. Until a new sheet number is read, all processed components will be output to that sheet. An informational-type message will be output if the previous item’s sheet number was set to 0 and the current sheet number is a new sheet. This reminds you to verify that all items were put on the correct sheet. The message will include the occurrence number of the item with sheet set to 0. A message to be used by the piping software is output in the MTO format. Error and Warning messages concerning sheet splits are output to the end of idf generation.

Correcting Incorrect Splits If an item has a 0 in the isometric_sheet_no column of the database, it is treated as either an additional item or the previous item was deleted and replaced with a new item. In this situation, a general rule has been established: Items whose sheet number is set to 0 will be output on the previous item’s sheet. Such that, when a starting item has its sheet number set to zero, the item would appear on sheet number 1. If necessary, this situation can be corrected by setting the isometric_sheet_no of the appropriate item to the correct sheet number in the design database. If more than one item in a series of items have sheet numbers set to 0, find the item that should start the new sheet and change the isometric_sheet_no to the correct number.

15.5 Determining Spool Split Points __________________________________________________________________________________________________________________________________________________ Like sheet split points, a spool split location is identified by comparing current piece_mark_no (spool number) with previous item’s spool number (excluding spool number 0). Location of the split between spools will be saved and output after the .idf file has been generated and all split locations have been determined. Items with spool number 0 will be placed on the current spool being processed. The spool split locations are determined using the following rules: Sheet numbers that are 0 are not considered for sheet split records. Unless otherwise stated, they are not considered as a sheet change. When a component is processed and has a sheet number different from previously processed components, a sheet split record is created. Until a new sheet number is read, all components processed will be output to that sheet.

15 - 6


An informational-type message will be output if the previous item’s spool number was set to Blank and the current spool number is a new spool. This reminds you to verify that all items were put on the correct spool. The message will include the occurrence number of the item with spool set to 0. A message to be used by the piping software is output in the MTO format.

Welds 16 - 1

16. Welds

__________________________________________________________________________________________________________________________________________________

The following is a list of weld features available in the ISOGEN software: Delivered weld symbols Dotted weld symbols User-defined weld symbols Codelist values for standard notes 180 and 1100 Weld type and mapping Offshore fabrication category Unique weld numbering User-defined weld prefix User-defined weld summary report Welds listed in the bill of materials A weld type defined as codelist value 2 will be interpreted as a no weld connection. This can be used when a weld is not wanted on match lines or pipe and pipe bends. All PDS applications recognize codelist value of 2 (from codelist 1100: weld type) as a no weld connection. For pipe bends, change skey PB to PBBW designates to the ISOGEN software that the connection is a butt weld. ISOGEN will automatically place a shop weld symbol at the connection and include the correct data in the cut list. The delivered map file will not change (set to PB by default).

Weld Enhancements - Related Information The following is a list of related elements within the ISOGEN software that may be manipulated when creating a Weld Enhancement. Related ISOGEN Options (Appendix B) 22, 53, 54, 74, 75

16 - 2


Related Intergraph Options (Section 7) 62, 69 Also: The twelfth entry in the FILES Section of the Options File: Weld Definition Report Format File (WDF) (See Chapter 8) Related Options File Material (Section 7) USER_DEFINED_WELDS OFFSHORE_FABCAT_CODE_LIST_VALUES WELD_PREFIX Related ISOGEN ATEXT Records (Appendix B) -414, -415, -416, -417, -418, -419, -421, -422, -423, -457

Delivered weld symbols

__________________________________________________________________________________________________________________________________________________

SKEYs for Existing Weld Types Description ___________

SKEY ______

Field Fit Weld Mitre Weld Mitre field fit Offshore Weld Offshore Weld Field Fit Workshop Site Erection Weld Connection

WF (Can add extra length to pipe) WM WMF WO WOF WW WS XX (Where XX would be for fittings with SW, SC, CP)

16.1 Dotted Weld Symbols __________________________________________________________________________________________________________________________________________________ Dotted weld symbols can not be redefined, and are intended for internal program use only. They are automatically selected when the need for a dotted weld is detected by the ISOGEN software. Dotted welds should be used when: a dotted pipeline continuation situations occurs dealing with a pipeline that has a special status of dotted open ends of a pipeline terminate with a welded end

Welds 16 - 3

New Dotted SKEYs for Weld Symbols Description ___________

SKEY ______

Workshop Site Field Fit Weld Mitre Weld Mitre Offshore Weld Offshore Weld Field Fit Erection Weld Connection on fittings with SW, SC, CP

WWD WSD WFD WMD WMFD WOD WOFD XXD

16.2 User-defined Weld Symbols __________________________________________________________________________________________________________________________________________________ The following is a list of guidelines that must be followed when creating a new weld symbol. Mitre welds can not be redefined. All other weld symbols can be user-created. New weld symbols can be generated just as any other user-defined symbol with the Isometric Symbol Editor, located under the Utilities option. Refer to Entering the Iso Symbol Editor Environment, page 5 - 72 for more information.

16.3 Codelist Values for Standard Note 180 and 1100 __________________________________________________________________________________________________________________________________________________ When the ISOGEN software is used to segregate offshore welds and identify mitre welds, standard note tables 180 and 1100 should be revised to accommodate this functionality. Changes to these tables will allow you to define which items will be in the offshore category of the bill of materials. Making revisions to standard notes 180 and 1100 will also allow different graphics symbologies of weld connections (offshore, mitre.). For more information, see Weld Types and Mapping, page 16 - 3 .

16.4 Weld Types and Mapping __________________________________________________________________________________________________________________________________________________ To define a weld type (shop, field, offshore) and weld symbology, revise the options file table USER_DEFINED_WELDS. This allows you to create a weld symbol and identify those weld-type codelist numbers (CL 1000) that will have a different weld symbol on the isometric drawing. It is also possible to map the weld symbol (existing or user-defined) to the appropriate weld-type codelist number by revising the USER_DEFINED_WELDS section. For more information, see USER_DEFINED_WELDS, page 7 - 45 . When the USER_DEFINED_WELDS section is not added to the options file: Shop welds (WW SKEY) and field fit welds (WF SKEY) are the only available types of welds.

16 - 4


Shop welds are given fabrication codelist value numbers 11 through 20 inclusive. No Weld is given fabrication codelist value 1. Field fit welds are given all other fabrication codelist value numbers with the exception of 1, and 11 through 20.

16.5 Offshore Fabrication Category __________________________________________________________________________________________________________________________________________________ The ISOGEN software offers and optional feature for segregating offshore fabrication category in the bill of materials. The OFFSHORE_FABCAT_CODE_LIST_VALUES section in the options file is used in the same way as the Shop FABCAT section. For more information, see OFFSHORE_FABCAT_CODE_LIST_VALUES, page 7 - 80 . If the codelist number is not listed in the option file sections for SHOP_FABCAT_CODE_LIST_VALUES or OFFSHORE_FABCAT_CODE_LIST_VALUES the item will default to field.

16.6 Unique Weld Numbering __________________________________________________________________________________________________________________________________________________ The ISOGEN software has the ability to display unique weld numbers from the piping database and display them on the isometric drawing. Since a PDS-generated weld number is eight characters long, the weld number is an arrowed message. If an enclosure is chosen for weld numbering (see ISOGEN option 75), it must be one of the following: diamond ended box round ended box rectangular box If an enclosure is not chosen, the default will generate a normal arrowed message with no box that points to the weld.

16.7 User-defined Weld Prefix __________________________________________________________________________________________________________________________________________________ The ISOGEN software allows the addition of weld prefix when using weld numbering. A weld prefix may be used: As a prefix to the actual weld number on the isometric in a box. The box shape to be set in Isogen option 75. As a form of general note about weld identification when positioned on the drawing frame.

Welds 16 - 5

As part of the output in the user-defined weld summary report to identify each weld. For more information, see WELD_PREFIX, page 7 - 47.

16.8 The Weld Summary Report __________________________________________________________________________________________________________________________________________________ A printed weld summary report is generated by setting Intergraph option 69. A new file name in the FILES Table (refer to The Files Table, page 7 - 42 ) of the options file is required if a user-defined format of the weld summary report is to be used. The designated file can be used for both the weld summary on the isometric drawing and the printed weld summary file. This optional file is referred to as the Weld Definition File (WDF) and is the twelfth entry in the FILES Table of the options file. The WDF file allows you to specify, within certain limits, the style and content of: The headings and data content of an alternative weld box to the normal weld box that is generated using ISOGEN option switch 53. Any alternative box’s output on the isometric in the same position as the normal weld box will be located in the bottom right corner of the isometric drawing area. The headings and data content of the weld summary report. If the Intergraph option to generate a weld summary report is set to 1 and the WDF file name is undefined, a Warning Error will be issued and the weld summary report will not be created. The report file name will be isoname.wXX where XX is the revision number.

16.8.1 Weld Definition File Format __________________________________________________________________________________________________________________________________________________ The Weld Definition File (WDF) allows the user to: Define the format of an alternative weld box displayed on the isometric drawing Define a backing sheet on the drawing frame Define the format of the Weld Summary Report As a general rule, all heading and title formatting must be positioned in the file exactly as it is positioned on the printed output. Title elements, other than unique identifiers, can be used with any format. Data item identifiers will be enclosed in single quotation marks. Unique identifiers will be used to determine what is defined and must match exactly. These identifiers include:

WELD-BOX-HEADINGS WELD-BOX-DATA-ITEMS WELD-INFO-CONTROLS WELD-INFO-DATA-ITEMS WELD-SUMMARY-TITLES

16 - 6


WELD-SUMMARY-COLUMN-HEADINGS WELD-SUMMARY-DATA-ITEMS

Weld Boxes - Alternative Style Available formats for Weld boxes include headings, box data items, controls and information data items. There is no imposed limit on the width of the user-defined weld box. Although, keep in mind that the weld box takes up space in the isometric drawing area. Therefore, the width should be kept to an absolute minimum. Blank characters can be used as required. Blank columns are allowed. Use the | character to indicate vertical column positions. Weld box headings can be any ascii string. Weld box data items must carry: — a data item identifier — a start position along the horizontal line — a justification marker Weld Box Data Item Identifiers: Identifier _________

ATEXT Used _____________

WELD-NO WELD-CAT N.S. WELD-TYPE

-414, -415, -416 -414, -415, -416 -417, -418, -419,-421, -422, -423

Weld Box Justification Markers R L C

Right Justified Left Justified Center Justified

Weld Boxes - Using a Backing Sheet When this form of weld information output is used, a design file (drawing frame) must be provided. The design file must contain an area that can receive weld information. The format is user definable, but no column headings are defined. All column headings must already exist in the design file.

Welds 16 - 7

This style of output requires two types of information: Basic Weld Control Information Weld Data Item Information Basic Weld Control Information Unless otherwise stated, where a number is required it will be integer or in real mm’s with only one decimal place allowed. Unless otherwise stated, all of the following inputs are mandatory. Define the form of list to be output by entering one of the following.

CONTINUOUS-DOWN CONTINUOUS-UP

Define start positions for information using the format: START-POSITION XPOS YPOS

Where: XPOS and YPOS is the x and y location in the design file. Define the vertical spacing between each line of horizontal text on the welding list using the format: VERTICAL-SPACING value

Define the maximum number of lines that can be printed before automatic overflow onto another sheet occurs using the format: MAXIMUM-ENTRIES value

Where: value is an integer Define the character height used for weld information using the format: TEXT-HEIGHT value

Define the level where weld information should be placed. (Optional) Use the format: DRAWING-LAYER value

Where: value is a level 1 - 63 Define the weight of characters output. (Optional) TEXT-THICKNESS

Where: value is a weight 0 - 10

16 - 8


Weld Data Item Information Data items must carry a data item identifier and start position information ( The x position in mm’s locates the bottom left hand point of the text string to be plotted. All text will be LEFT justified). Weld Box Data Item Identifiers Identifier _________

Used _ATEXT ____________

WELD-NO WELD-CAT N.S. WELD-TYPE

-414, -415, -416 -414, -415, -416 -417, -418, -419,-421, -422, -423

Weld Summary Report The weld summary report page length is controlled by ISOGEN option switch 63. When generating this report three sections of data are required in the WDF file. These include: The printed weld summary title definitions (WELD-SUMMARY-TITLES) This section can contain two types of information — Heading titles — Data items to be listed with the title Unique identifiers available for title information:

PIPELINE-REFERENCE PIPING-SPEC DATE-DMY PAGE

The column heading definitions (WELD-SUMMARY-COLUMN-HEADINGS) — This section can be any ascii string. The data definitions to be listed in each column (WELD-SUMMARY-DATA-ITEMS) Refer to the previous definition of Weld Box Data Item for the format of this section. ’ ’ used with PAGE attribute indicates program generated page number. ’Blank’ indicates a blank line. The overall width of the weld summary report should not exceed 130 characters.

Welds 16 - 9

16.8.2 Example WDF File __________________________________________________________________________________________________________________________________________________ An example for an alternative weld list in the WDF file:

WELD-BOX-HEADINGS | Weld | Weld | N.S. | Weld | Welder | | No | Cat | mm | Type | ID | WELD-BOX-DATA-ITEMS ’WELD-NO’4 R ’WELD-CAT’ 10 L ’N.S.’ 17 L ’WELD-TYPE’ 25 L

An example for user defined backing weld list in the WDF file:

WELD-INFO-CONTROLS CONTINUOUS-DOWN START-POSITION 225.0 VERTICAL-SPACING 4.5 MAXIMUM-ENTRIES 20 TEXT-HEIGHT 2.5 DRAWING-LAYER 16 TEXT-THICKNESS 2

80.5

WELD-INFO-DATA-ITEMS ’WELD-NO’ 225.0 ’WELD-CAT’ 235.0 ’N.S.’ 245.0 ’WELD-TYPE’ 260.0

An example for a user defined weld summary report in the WDF file:

WELD-SUMMARY-TITLES WELD SUMMARY PAGE ’ ’ ’Blank’ PIPELINE REF: ’PIPELINE_REFERENCE’ ’Blank’ PIPING SPEC : ’PIPING-SPEC’

16 - 10


WELD-SUMMARY-HEADINGS Weld Weld N.S. No Cat mm ____ ____ ____

Weld Type ____

Welder ID ______

WELD-SUMMARY-DATA-ITEMS ’WELD-NO’8 R ’WELD-CAT’ 17 L ’N.S.’ 26 L ’WELD-TYPE’ 37 L

16.9 Welds Listed in the Bill of Materials __________________________________________________________________________________________________________________________________________________ For welds listed in the BOM: Intergraph option 62 controls material pointers for welds. The commodity code will be SHOP, FIELD or OFFSHORE. The description will be weld type, material grade A and material grade B.

Dimensioning and Coordinate Output 17 - 1

17. Dimensioning and Coordinate Output

__________________________________________________________________________________________________________________________________________________

Coordinate and Dimensioning Features - Related Information The following is a list of related elements within the ISOGEN software that may be manipulated to change dimensioning/coordinate output. Related ISOGEN Options (Appendix B) 9, 41, 66, 80, 81, 119 Related Intergraph Options (Section 7) NONE Related Options File Material (Section 7) NONE Related ISOGEN ATEXT Records (Appendix B) -455

17.1 Dimensioning Features __________________________________________________________________________________________________________________________________________________ ISOGEN’s dimensioning features allows you to: Dimension Valve Centerlines Suppress Branch Dimensioning String Dimensioning Gaskets Included In Flanged Component Dimensions USA Style Dimensioning Non-Dimensioned Supports ISOGEN option 119 controls vertical dimensions/elevations. See Appendix B, Alias ISOGEN Tables, for more information.

17 - 2


Dimensioning Valve Centerlines This feature dimensions valves with certain bores and/or end conditions dimensioned to their centerline only, using string or composite dimension types. This is controlled by ISOGEN option 80 and 81. Centerline dimensioning on valves will only work with valves that have a spindle point define. Refer to Entering the Iso Symbol Editor Environment, page 5 - 72 for information on defining a spindle point. ISOGEN option 80 defines the end type that will be dimensioned to the item’s centerline. ISOGEN option 81 determines the upper size limit of valves that will be dimensioned to their centerline. All diameters that exceed the value specified by switch 81 are dimensioned normally. ISOGEN options 80 and 81 provide the complete definition of valves which will be dimensioned to their centerline. Units of input for the size limit are defined with ISOGEN 41. See Appendix B, Alias ISOGEN Tables, for more information. Suppressing Branch Dimensioning This feature suppresses branches and tee bends/elbows with certain bores and/or number of components. Units of input for the size limit are defined by ISOGEN option 41. ISOGEN option 81 determines the upper size limit of branches whose dimensioning will be suppressed. All branch sizes that exceed the value specified by switch 81 are dimensioned normally. ISOGEN option 81 also determines the upper limit of components in a branch run that will have dimensioning suppressed. A branch run that exceeds the number of defined components is dimensioned normally. See Appendix B, Alias ISOGEN Tables, for more information. String Dimensioning This feature allows pipeline components to be dimensioned individually. ISOGEN option 9 flags individual dimensions to be output for every component in the pipeline. See Appendix B, Alias ISOGEN Tables, for more information. Gaskets Included in Flanged Component Dimensions This feature allows dimensioned flanged components to include gaskets (if present) in the dimension. Leader lines from adjoining flanges are displayed, while dimension leader lines from valve ends are not displayed.

Dimensioning and Coordinate Output 17 - 3

ISOGEN option 9 flags dimensioning to include gasket thickness. See Appendix B, Alias ISOGEN Tables, for more information. USA Style Dimensioning This feature displays the dimension on top of the dimension line. ISOGEN option 9, causes dimensions to be displayed on top of the witness line (USA style).

17.2 Coordinate Features __________________________________________________________________________________________________________________________________________________ ISOGEN’s coordinate features allow you to: Extend Witness Lines Display Elevations at Bend/Elbow Intersections Display Elevations at Branch Intersections Display Split Point Coordinates ISOGEN option 119 controls vertical dimensions/elevations. See Appendix B, Alias ISOGEN Tables, for more information. Extend Witness Line This feature allows elevations/coordinates to be output along an extended witness line at bends/elbows. ISOGEN option 66, displays elevations/coordinates along extended witness lines. See Appendix B, Alias ISOGEN Tables, for more information. Display Elevation at Bend/Elbow Intersections This feature allows you to: Suppress Elevations at bend/elbow intersections Partial set of coordinates at bend/elbow intersections Only the coordinates that have changed A full set of coordinates at bend/elbow intersections. ISOGEN option 66 is used to define the Display Elevation at Bend/Elbow Intersections feature.

17 - 4


See Appendix B, Alias ISOGEN Tables, for more information. Display Elevations at Branch Intersections This feature allows you to: Suppress elevations at branch intersections Display a partial set of coordinates at a branch intersection Display only the coordinates that have changed Display a full set of coordinates at branch intersections ISOGEN option 66 is used to define the Display Elevation at Branch Intersections feature. See Appendix B, Alias ISOGEN Tables, for more information. Split Point Coordinate Display This feature allows a full set of coordinates at iso split points to be grouped with a continuation note. ISOGEN option 66 is used to define the Display Elevation at Branch Intersections feature. See Appendix B, Alias ISOGEN Tables, for more information.

Detail Sketch and Information Note Facility 18 - 1

18. Detail Sketch and Information Note Facility

__________________________________________________________________________________________________________________________________________________

The Detail Sketch Facility allows pre-defined detail sketches (MicroStation cells) to be automatically selected and positioned on the isometric drawing. In addition, a cross reference is added to the referenced item on the plotted pipeline. The Information Note Facility automatically selects general or specific notes (MicroStation cells) and positions them on the isometric drawing in the same manner as detail sketches. The initial information note is placed in the lower left corner of the drawing with additional notes being placed to the right along the bottom of the drawing. Information notes and detail sketch cells can be placed on the same drawing.

18 - 2


Detail Sketch/Information Note Facility - Related Information The following is a list of related elements within the ISOGEN software that may be manipulated when using the Detail Sketch Facility. Related ISOGEN Options (Appendix B) 71, 92 Related Intergraph Options (Section 7) 66 Related Options File Material (Section 7) DETAIL_SKETCH_FACILITY Also: The tenth entry in the FILES section of the options file: cell library. This entry defines the microstation cell library that contains the detail/note cells. The eleventh entry in the FILES section of the options file: DDF file. This entry in the options file defines the DDF (Data Definition File) that will be used to determine graphic parameters for the detail sketch/note. Related ISOGEN ATEXT Records (Appendix B) -456, -541, -542

18.1 Detail Sketch Entries in the DDF __________________________________________________________________________________________________________________________________________________ This is an example of the portion of the Data Definition File (DDF) that pertains to the Detail Sketch facility.

DETAIL-SKETCH FILE-FORMAT SKETCH-SIZE CROSS-REFERENCE TEXT-HEIGHT TEXT-THICKNESS DRAWING-LAYER

DXF 50 50 35 5 ALPHA 3 2 1

Where: DETAIL-SKETCH

is the section header in the DDF.

FILE_FORMAT DXF

determines the format of the detail. This line is ignored by PD_ISO.

Detail Sketch and Information Note Facility 18 - 3

SKETCH-SIZE 50 50

determines the X-Y size of the detail on the iso. The value is in either millimeters or inches (determined by ISOGEN switch 92).

CROSS-REFERENCE 35 5 ALPHA

determines the X-Y cross reference position on the detail in either millimeters or inches (determined by ISOGEN switch 92), and the character type of the cross reference text.

TEXT-HEIGHT 3

determines the text height for the cross reference identifier.

TEXT-THICKNESS 2

determines the weight of the text for the cross reference identifier.

DRAWING-LAYER 1

determines the level for the cross reference identifier text.

For more information about the DDF, refer to Isometric Presentation, page 20 1.

18.2 Information Note Entries in the DDF __________________________________________________________________________________________________________________________________________________ This is an example of the portion of the DDF that pertains to the Information-Note facility. INFORMATION-NOTE FILE-FORMAT DXF NOTE-SIZE 50

20

Where: INFORMATION-NOTE

is the section header in the DDF.

FILE-FORMAT DXF

determines the format of the note cell. This line is ignored by PD_ISO.

NOTE-SIZE 50 20

determines the X-Y size of the detail on the iso. The value is in either millimeters or inches (determined by ISOGEN switch 92).

18 - 4


Weight Display 19 - 1

19. Weight Display

__________________________________________________________________________________________________________________________________________________

The Weight Display Facility allows the weight stored in the Design database for each component to be extracted from the 3D model and listed on the isometric material list. Total weight can be generated for the pipeline, for the Fabrication (Shop) components, for the Erection (Field) components, and for Offshore components. Spool weight can be generated for Spool isometrics.

Weight Display - Related Information The following is a list of related elements within the ISOGEN software that may be manipulated when using the Weight Display Facility. Related ISOGEN Options (Appendix B) 41 Related Intergraph Options (Section 7) 47, 63 Related Options File Material (Section 7) NONE Related ISOGEN ATEXT Records (Appendix B) -352, -353, -354, -355, -379, -380, -381 Weight will be interpreted as: Unit weight of a component Weight per length of a pipe/tube Where: length is a foot in Imperial Units, and a Meter in Metric units A Warning Message will be output to the error file when weight has not been recorded in the design database for a pipe/component:

(35:1111) Warning - Component(s) with no Weight found

19 - 2


19.1 Center of Gravity Calculation __________________________________________________________________________________________________________________________________________________ Before Calculating the Iso Center of Gravity 1.

Generate an ISAM center of gravity weight library. From Windows File Manager or the DOS prompt, run the ˜\pdiso\bin\bldwtlib.exe executable to generate or update an ISAM weight library. Once initialized, bldwtlib prompts you to input an ASCII weight library neutral file. The default, weight_lib.neu, is located in the ˜\pdiso\examples directory and contains entry definitions and example data that can be referenced to make a custom weight library neutral file. After a weight library neutral file is defined, you are prompted to enter a name or use the default name, cog_weight.l, for the resulting ISAM weight library. By default, the file is written to the examples directory.

2.

Set Intergraph option 63 to 1.

3.

Edit the ISOGEN options file. — Define the name of the ISAM center of gravity library under the ninth entry of the FILES category. This is the library that will be used to make center of gravity calculations. For example, ’˜\pdiso\examples\cog_weight.l’

!COG WEIGHT LIBRARY

— Define the center of gravity entry in the MTO record map, which is the fifth entry of the FILES category. For example, ’˜\pdiso\examples\cogmto.tbl’

!MTO RECORD MAP

If the Debug switch on the Submit Batch Job form is set to on, a center of gravity report file, .cog, is written to the output directory. If the Verify on the Submit Batch Job form is set to on, additional Intergraph information about each component is added to the center of gravity report file. In the STIB data file (used to place drawing title block text), center of gravity x, y and z coordinates are assigned as node numbers 908, 909 and 910 respectively.

Isometric Presentation 20 - 1

20. Isometric Presentation

__________________________________________________________________________________________________________________________________________________

ISOGEN’s Presentations feature allows you to customize the presentation of a generated isometric drawing. ISOMETRIC-DEFINITION is the identifier used when defining information for Isometric Presentations. When using the user-defined formats, it is your responsibility to ensure (by doing trial runs) that the specified options are practical and produce the required isometric presentation before committing to project use.

The drawing definition file (DDF) contains user-defined requirements that determine the final plotted isometric presentation. The DDF file is the eleventh entry in the FILES section of the options file. In addition to containing isometric presentation information, the DDF also contains Detail Sketch definition data (DETAIL-SKETCH). Subsection identifiers for user-defined presentation features include: PIPELINE-ATTRIBUTES PIPELINE-ATTRIBUTES-SPECIAL PIPELINE-ATTRIBUTES-DOTTED BEND/ELBOW-REPRESENTATION FITTINGS-GENERAL FITTINGS-SPECIAL FITTINGS-UNDIMENSIONED-BRANCHES MISC-ITEMS LAYER-NAMES An example data definition file is located at the end of this section.

20 - 2


The DDF uses the following conventions: Must be an ascii character file. All identifiers (Main and Sub-section) plus all data attributes must start in position one on a new line. No spaces are allowed in any identifier or attribute name. Use of any of the subsection identifiers is optional. Program defaults will be used as required.

Isometric Presentation - Related Information The following is a list of related elements within the ISOGEN software that may be manipulated when defining a isometric presentation. Related ISOGEN Options (Appendix B) NONE Related Intergraph Options (Section 7) NONE Related Options File Material (Section 7) NONE The eleventh entry in the FILES Section of the Options File: Data Definition File (DDF) (See Chapter 8) Related ISOGEN ATEXT Records (Appendix B) NONE


20.1 PIPELINE-ATTRIBUTES __________________________________________________________________________________________________________________________________________________ The PIPELINE-ATTRIBUTES section of the DDF allows you to define the following characteristics for a plotted pipeline (Pipe, Elbows, Bends, Tees, Crosses, etc.): N.S. (Bore Units) N.S. Range Plotted Pipe Thickness Layer (Level) number Attribute/Data Identifiers Bore Units

N.S. Data

Data = inches or mm

N.S. Range

N.S.RANGE min and max bore

min/max bores may be stated in either Integer or Real (such as, 1 1.0 1.5 10 10.0)

Thickness

THICKNESS data 1 data 2

data 1 = Integer number representing required thickness. data 2 = Actual Thickness (width) of plotted line in mm (Real Number).

Layer

LAYER data

data is an Integer identifying the required Layer (Level) to which the Pipeline is to be assigned.

Example PIPELINE-ATTRIBUTES Input: PIPELINE-ATTRIBUTES N.S. INCH N.S.RANGE 0 2 THICKNESS N.S.RANGE 2.5 6 THICKNESS N.S.RANGE 8 * THICKNESS

2 4 6

1.0 2.0 2.5

LAYER LAYER LAYER

10 10 10

Guidelines for Defining PIPELINE-ATTRIBUTES Input: Any number of Spaces are allowed between the attribute identifier and data items. All lines must start in position one. Allow space for a maximum of five N.S. RANGE records. Use of LAYER is optional. If LAYER is not set, the ISOGEN default LAYER set will be used. An * is allowed in last maximum bore position to signal that there is no maximum bore limit.

20 - 4


THICKNESS data 1 attribute is used to define required line weight in plotfile output. THICKNESS data 2 is used by the ISOPLOT module of ISOGEN when positioning Messages along the pipeline.

20.2 PIPELINE-ATTRIBUTES-SPECIAL __________________________________________________________________________________________________________________________________________________ The PIPELINE-ATTRIBUTES-SPECIAL section of the DDF is used in the same way as the PIPELINE-ATTRIBUTES feature except that the attributes set only apply to pipeline sections designated Special Status. Special Status is recognized when attribute status is set to DOTTED or NOMTO.

20.3 PIPELINE-ATTRIBUTES-DOTTED __________________________________________________________________________________________________________________________________________________ The PIPELINE-ATTRIBUTES-DOTTED section of the DDF allows you to define thickness and layer attributes for the following three categories of dotted representation. Dotted Special Status (SPECIAL-STATUS; such as Dotted, NO-MTO Items) Dotted Pipeline Continuations (PIPELINE-CONTINUATION) Dotted items at isometric Split Points (DRAWING-SPLIT-POINTS) Example PIPELINE-ATTRIBUTES-DOTTED Input: PIPELINE-ATTRIBUTES-DOTTED SPECIAL-STATUS THICKNESS PIPELINE-CONTINUATION THICKNESS DRAWING-SPLIT-POINTS THICKNESS

3 3 3

1.75 1.75 1.75

LAYER LAYER LAYER

15 16 17

Guidelines for Defining PIPELINE-ATTRIBUTES-DOTTED Input: The SPECIAL-STATUS, PIPELINE-CONTINUATION or DRAWING-SPLIT-POINT identifiers may be included in any order following the main section identifier. Use the THICKNESS and LAYER data as described for PIPELINE-ATTRIBUTES. N.S.RANGE or Bore Units are not allowed in this section. Dotted representation is the same for all bores. If a PIPELINE-ATTRIBUTES-SPECIAL section is included in the file, any setting for SPECIAL-STATUS found in this section will be ignored. Use of LAYER is optional. If LAYER is not set, the ISOGEN default LAYER setting will be used.


Care should be taken when specifying the THICKNESS data for any of these Dotted categories. All three categories can involve the plotting of Dotted Fittings that may look unacceptable if thickness for Dotted representation is too thick.

20.4 BEND/ELBOW-REPRESENTATION __________________________________________________________________________________________________________________________________________________ The BEND/ELBOW-REPRESENTATION section of the DDF allows you to define Elbows and Bends to be either Round or Square when displayed on the isometric drawing. Example BEND/ELBOW-REPRESENTATION Input: BEND/ELBOW-REPRESENTATION BEND data ELBOW data

Where: data

can be set to either SQUARE or ROUND If no setting is defined, ROUND is used as the default.

20.5 FITTINGS-GENERAL __________________________________________________________________________________________________________________________________________________ The FITTINGS-GENERAL section of the DDF allows you to define attributes for all Fittings. These attributes include: N.S. (Bore Units) N.S. Range Plotted Fitting (Component) Thickness Layer (Level) number Fitting Scale (Plotted size of fittings) (to be applied to standard ISOGEN symbols) Attribute/Data Identifiers Include: Bore Units

N.S. data

N.S. Range

N.S. RANGE min bore max bore

Thickness

THICKNESS data 1 data 2

Layer

LAYER data

Scale

SCALE data

Where:

20 - 6


data

is a two- or three-digit Integer that represents an increase or decrease to the basic 100% standard symbol size for all types of fittings.

Example FITTINGS-GENERAL Input: FITTINGS-GENERAL N.S. INCH N.S.RANGE 0 2 THICKNESS N.S.RANGE 2.5 6 THICKNESS N.S.RANGE 8 * THICKNESS

2 3 4

1.5 LAYER 1.75 LAYER 2.0 LAYER

20 20 20

SCALE SCALE SCALE

100 150 200

20.6 FITTINGS-SPECIAL __________________________________________________________________________________________________________________________________________________ This FITTINGS-SPECIAL section of the DDF allows you to define Thickness, Layer or Scale attributes for specific types of components. The settings presented in this section will override the Fittings-General settings for the selected types of components. Definable Attributes Include: THICKNESS LAYER SCALE

Data requirements for the previous attributes are the same as the data requirements for FITTINGS-GENERAL. Any of the previous attributes can be set for a specific type of component. But, if FITTINGSSPECIAL attributes are not defined, ISOGEN defaults to the FITTINGS-GENERAL. For example: If LAYER 40 was the only special attribute set for INSTRUMENTS, it would be used for all INSTRUMENTS (all bores), but any Thickness and / or Scale attributes would be used from the FITTINGS-GENERAL section. Whenever a Scale attribute is set in this section, the Scale factor will not be used as a direct scale to the standard symbol. It will instead be used as a Multiplier to any Scale set in the FITTINGS-GENERAL section. For example: Scale 150 set in Fittings-General Scale 75 set in Fittings-Special Scale to be used on nominal Fitting type is 150 x 0.75 = 113 (to nearest whole number).


Example FITTINGS-SPECIAL Input: FITTINGS-SPECIAL INSTRUMENTS LAYER 30 OLETS SCALE 75 SUPPORTS THICKNESS

4

2.0

(Put all Instruments on Layer 30) (Olets to be scaled down) (All Supports to be plotted)

Fitting type identifiers OLETS INSTRUMENTS SUPPORTS WELDS COUPLINGS CAPS UNIONS FLANGES FILTERS PIPE-BLOCKS SAFETY-DISC TRAPS REDUCERS VALVES VALVES-ANGLE VALVES-3WAY VALVES-4WAY NOZZLE END-CONNECTORS HYGENIC-CONNECTORS MISC-COMPONENTS MISC-COMPONENT-PLUG MISC-COMPONENT-RESTRICTOR MISC-COMPONENT-SLIPPLATE MISC-COMPONENT-SLIPRING MISC-COMPONENT-SPECBLIND

20.7 FITTINGS-UNDIMENSIONED-BRANCHES __________________________________________________________________________________________________________________________________________________ The FITTINGS-UNDIMENSIONED-BRANCHES of the DDF section allows you to vary the Thickness, Layer and Scale of any component that is included in any Undimensioned Branch. Attributes/Data identifiers are the same as the attributes/data identifiers for FITTINGSGENERAL. Example FITTINGS-UNDIMENSIONED-BRANCHES Input: FITTINGS-UNDIMENSIONED-BRANCHES N.S. INCH N.S.RANGE 0 1 THICKNESS 1 1.0 N.S.RANGE 1.5 2 THICKNESS 2 1.5

LAYER LAYER

10 10

SCALE SCALE

60 75

These parameters should only be used when the Branch Dimension Suppression facility is being used (ISOGEN option switch 81). It will be up to you to verify that any N.S.RANGE set in the FITTINGS-UNDIMENSIONED-BRANCHES section matches the Bore range set in Option Switch 81.

20 - 8


All Pipe fittings (Elbows, Tees, etc.) are plotted the same thickness as a tube.

20.8 MISC-ITEMS __________________________________________________________________________________________________________________________________________________ The MISC-ITEMS section in the DDF allows you to set the Thickness and Layer data for the following types of miscellaneous items that appear on an isometric drawing: DIMENSION-TEXT DIMENSION-LINES ISO-TEXT FRAME-TEXT SKEWS HATCHING LAGGING TRACING FRAME WELD-BOX SPEC-BREAKS MATERIAL-LIST (Styles 1 nd 2 only)

Example MISC-ITEMS Input: MISC-ITEMS DIMENSION-TEXT DIMENSION-LINES SKEWS HATCHING

THICKNESS THICKNESS THICKNESS THICKNESS

2 1 2 1

0.8 0.6 0.8 0.6

LAYER LAYER LAYER LAYER

22 23 25 25

Any undefined attribute uses the ISOGEN defaults.

20.9 LAYER-NAMES __________________________________________________________________________________________________________________________________________________ The LAYER-NAMES section in the DDF allows you to issue standard Names to any layer number used in any of the other sections. Example LAYER NAMES Input: LAYER-NAMES 10 ’10’ 12 ’12’ 22 ’22’

Where 10 is the Layer Number and the text within the ’’ is the Layer Name.

10

is the layer number

’10’

is the layer name. Because Microstation LAYERS are numbers, NAMES must be the same as the LAYER. Up to 50 names can be defined.


20.10 Program Defaults __________________________________________________________________________________________________________________________________________________ The table below shows the program default settings for THICKNESS and LAYER for the various elements that are used in the generation of a plotted isometric drawing. Element ________

Default Thickness __________

Default Layer ______

Pipeline (including Elbows, Tees, etc.)

3 (0.6 mm)

1

All Fittings

2 (0.25 mm)

2

All drawing Text and other miscellaneous items

1 (0.1 mm)

3

Drawing Frame, Frame text, Weld Box, etc.

1 (0.1 mm)

4

Dotted items

1 (0.1 mm)

5

Material List

1 (0.1 mm)

6

20 - 10


20.11 Example Drawing Definition File __________________________________________________________________________________________________________________________________________________ ISOMETRIC-DEFINITION PIPELINE-ATTRIBUTES N.S. INCH N.S.RANGE 0 2 THICKNESS 2 0.65 LAYER 7 N.S.RANGE 2.5 6 THICKNESS 2 0.95 LAYER 29 N.S.RANGE 8 * THICKNESS 4 1.25 LAYER 30 PIPELINE-ATTRIBUTES-DOTTED DRAWING-SPLIT-POINTS THICKNESS 2 0.35 LAYER 19 SPECIAL-STATUS THICKNESS 2 0.65 LAYER 8 PIPELINE-CONTINUATION THICKNESS 2 0.35 LAYER 9 FITTINGS-GENERAL N.S. INCH N.S.RANGE 0 2 THICKNESS 2 0.30 LAYER 7 SCALE 105 N.S.RANGE 2.5 * THICKNESS 2 0.35 LAYER 7 SCALE 110 FITTINGS-SPECIAL INSTRUMENTS THICKNESS 2 0.30 LAYER 10 SCALE 115 NOZZLE THICKNESS 2 0.30 LAYER 11 CAPS THICKNESS 3 0.85 LAYER 38 COUPLINGS THICKNESS 3 0.65 LAYER 37 VALVES THICKNESS 2 0.30 LAYER 12 SCALE 180 FLANGES THICKNESS 2 0.30 LAYER 31 SCALE 120 UNIONS THICKNESS 2 0.30 LAYER 35 SCALE 110 OLETS THICKNESS 4 0.70 LAYER 34 SCALE 110 WELDS THICKNESS 2 0.30 LAYER 32 SCALE 130 REDUCERS THICKNESS 3 0.60 LAYER 33 SCALE 120 VALVES-ANGLE THICKNESS 2 0.30 LAYER 13 SCALE 180 VALVES-3WAY THICKNESS 2 0.30 LAYER 14 SCALE 150 VALVES-4WAY THICKNESS 2 0.30 LAYER 15 SCALE 150 SUPPORTS THICKNESS 4 0.90 LAYER 36 SCALE 130 PIPE-BLOCKS THICKNESS 2 0.30 LAYER 39 SAFETY-DISC THICKNESS 2 0.30 LAYER 40 FILTERS THICKNESS 2 0.60 LAYER 41 SCALE 280 TRAPS THICKNESS 2 0.60 LAYER 42 SCALE 180 END-CONNECTORS THICKNESS 2 0.30 LAYER 50 SCALE 120 HYGENIC-CONNECTORS THICKNESS 4 0.70 LAYER 50 SCALE 300 MISC-COMPONENTS THICKNESS 2 0.30 LAYER 49 SCALE 180 MISC-COMPONENT-RESTRICTOR THICKNESS 2 0.30 LAYER 44 MISC-COMPONENT-SLIPPLATE THICKNESS 2 0.30 LAYER 45 MISC-COMPONENT-SLIPRING THICKNESS 2 0.30 LAYER 46 SCALE 250 MISC-COMPONENT-SPECBLIND THICKNESS 2 0.30 LAYER 47 MISC-COMPONENT-PLUG THICKNESS 2 0.30 LAYER 48 FITTINGS-UNDIMENSIONED-BRANCHES N.S. INCH N.S.RANGE 0 2 THICKNESS 2 0.65 LAYER 43 SCALE 300 BEND/ELBOW-REPRESENTATION BEND ROUND ELBOW ROUND MISC-ITEMS DIMENSION-TEXT DIMENSION-LINES ISO-TEXT

LAYER 16 LAYER 17 LAYER 20


FRAME-TEXT SKEWS HATCHING LAGGING TRACING FRAME WELD-BOX SPEC-BREAKS MATERIAL-LIST LAYER-NAMES 1 ’1’ 2 ’2’ 3 ’3’ 4 ’4’ 5 ’5’ 6 ’6’ 7 ’7’ 8 ’8’ 9 ’9’ 10 ’10’ 11 ’11’ 12 ’12’ 13 ’13’ 14 ’14’ 15 ’15’ 16 ’16’ 17 ’17’ 18 ’18’ 19 ’19’ 20 ’20’ 21 ’21’ 22 ’22’ 23 ’23’ 24 ’24’ 25 ’25’ 26 ’26’ 27 ’27’ 28 ’28’ 29 ’29’ 30 ’30’ 31 ’31’ 32 ’32’ 33 ’33’ 34 ’34’ 35 ’35’ 36 ’36’ 37 ’37’ 38 ’38’ 39 ’39’ 40 ’40’ 41 ’41’ 42 ’42’ 43 ’43’ 44 ’44’ 45 ’45’ 46 ’46’ 47 ’47’ 48 ’48’ 49 ’49’ 50 ’50’

LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER

21 22 23 24 25 26 27 28 18

20 - 12


Isometric Types 21 - 1

21. Isometric Types

__________________________________________________________________________________________________________________________________________________

Isometric Type definitions allow more flexibility with the line name definition. By using Types feature, you can track drawing records more accurately and efficiently. Isometric Types also allow you to store the same line name multiple times in the database, each time as a different Type. For example, line ABC can be stored twice, once as Fabrication Type and once as Spool Type. The Type attribute creates a unique database entry. Isometric Types and Code List 1900 Isometric Types are supported by Code List 1900. Code List 1900, as delivered, contains 3 types. These types include: Fabrication Spool Stress The following is an example of Code List 1900. C1900 ; 1900, Iso Type ; NOTE: In editing this codelist set, do not change the meaning ; of existing codelist values. Some data displays require that only ; values to the left of the "=" sign be shown; other reports require ; that only values to the right of the "=" sign be displayed. 1 = ’Fabrication’ (Default Setting) 2 = ’Spool’ 3 = ’Stress’

You can add more options, if needed, to Code List 1900. For an example of setting isometric types, refer to Bulk Load Lines, page 5 - 57 . The Isometric Type is a new column in pdtable_185 of the Project Database. All records MUST have an Isometric Type, or they will not extract. Batch Input files contain Type information when they are created on ISOGEN software version 5.0 or later. Batch Input files created prior to 5.0 will extract, but a error message will be output that states that the batch input file is out of date, and needs to be replaced.

21 - 2


Appendix A: Warning and Error Messages A - 1

Appendix A

__________________________________________________________________________________________________________________________________________________

Warning and Error Messages

A-2



Appendix A

__________________________________________________________________________________________________________________________________________________

Warning and Error Messages This section lists the warning and error messages that are issued by the various components of the iso extraction software and suggested corrective action when that is possible. Please refer to the section entitled Software Organization for a discussion of the each of the components and how they are related.

A-4


A.1 Intergraph Interface to ISOGEN __________________________________________________________________________________________________________________________________________________ The messages that are issued by the Intergraph interface to ISOGEN are, for the most part, recorded in an error message file that is created along with the intermediate data file (the input file to ISOGEN) when errors occur. If no errors occur, then an error file is not created. Some messages generated in the file are not written to the screen as they only contain additional data on a reported error. There are three categories of messages issued by the software: Information - An error occurred that can result in other errors later on. Warning - An error occurred that can result in a problem on the drawing. The drawing should be checked. Error - An error occurred that is serious enough to cause extraction to abort. The drawing is not produced.


A.1.1 Information Messages __________________________________________________________________________________________________________________________________________________ I1 - The Graphic Commodity Library does not exist or an error occurred when it was opened. This message indicates a problem with the graphic commodity library. Make sure that it is properly attached to the primary (the first) model design file. If there is doubt then you should enter the file in graphics and try to place any component. Iso extraction requires read access to the file. I3 - Error opening Material Descriptions Library. This message indicates a problem with the material description library. The proper file should be attached to the primary (first) model file via the RDB software. Iso extraction requires read access to the file. I4 - Error opening Specialty Material Descriptions Library. This message is the same as I3 except that it pertains to the piping specialty and instrument material descriptions library. Note that if this library is not successfully opened then specialty items will NOT receive material descriptions in the iso bill-ofmaterial. If the file exists and is properly attached make sure that your process has read access to it. I5 - Error accessing the Label Descriptions Library. The label description library should be properly attached to the primary (first) model file via the RDB software. If this has been done, then a quick test using the drawing annotation commands might uncover the problem. Make sure that your process has read access to the file. I6 -Note file not defined I8 - Unrecognized key read from MTO Neutral File record map. This message occurs when the software encounters an unexpected record in the neutral file map. Usually, this indicated that the number of table entries to follow (the number following each keyword) is incorrect. I9 - Unrecognized key read from options file. This message occurs when the software encounters an unexpected record in the options file. All keywords are followed by a number that indicates the number of records to follow until the next keyword. If this number is incorrect then this message will result.

A-6


I10 - An error occurred while reading the PDS to ISOGEN symbol map. Some difficulty occurred while the PDS-to-ISOGEN symbol map file was being read in. Check the symbol map file that is defined in the options file for mistakes. I11 - Error reading in complete PDS to ISOGEN symbol map. The internal buffer used for holding the PDS to ISOGEN map has been filled by entries from the map file and some have thus been ignored. Contact Intergraph with this problem. I13 - Physical data library not read. This message indicates that the physical data library for the current component could not be read by the mto software for generating bolts and gaskets. If bolt/gasket generation has failed on the current component then this message indicates that the most likely reason is that an error occurred while trying to read the physical data library. If no bolts/ gasket generation failure occurred then the message might be ignored. I14 - Unrecognized key read from title block tables file This message indicates that an unexpected record was encountered in the title block tables file. It will usually indicate that the number of entries to follow value (on a record following a keyword) is incorrect. I16 - Intergraph option 34 reset to zero Intergraph option 34 applies only to batch extraction. When interactive extraction is run, this option is ignored. I17 - Intergraph option 16 reset to 0 I18 - Check number of lines entry in the options file. I19 - Error accessing specialty material descriptions library I20 - Error accessing the specified material description library I21 - Error accessing the specified label description library I22 - Error opening the label description library


I23 - The last start point is chosen to be the traversal start point Table: 3 Component Occ: 4195082 Segment Occ: 4194661 I24 - Alternate index is used to read material description library. The material description is not found with the default primary key, item code. The alternate index, defined in the ALTERNATE_DESCRIPTION_INDEX table in the option file, is used to find the material description. I25 - No existing sheet and no last start point for section 1 Iso extraction will continue as the first time

A-8


A.1.2 Warning Messages __________________________________________________________________________________________________________________________________________________ W1 - Error computing valve oper or reducer orientation. An error occurred in the calculations to orient a valve operator or an eccentric reducer. In both cases the connect point orientations should be checked in graphics to confirm that they are correct. W2 - Segment column is undefined. In checking for an attribute change at a segment endpoint the attribute being checked has gone from being defined with a value to being undefined (blank). The attributes defined in the PIPELINE_HEADER table in the options file should be checked and defined with a value as needed. W3 - Error forming label from label library. An error has occurred in creating a note or label using the label description library. The label (whose label number is also printed in the message) should be checked using the label description library software. W4 - Invalid LINE ID format - LINE ID ignored. A line ID that is either incorrect in format or contains invalid data has been input. Check the format of the line ID against the definition in the options file. Remember that each attribute that is part of the line ID must be separated from the others by a dash ( - ). An example of invalid data in the line ID might be a fluid code that does not exist in the fluid code codelist. W5 - Error reading in extraction criteria. An error has occurred reading in the line identification inputs from the input file. This might indicate a problem in the software that creates the input file. W6 - Model design file not found. This message indicates that the model design file read in from the input file either does not exist or that your process does not have read access to it. W7 - Error reading the Label Description Library. This message probably indicates that the label definition for a specific label does not exist in the label description library opened by the software. Make sure that the primary (first) model design file has the proper library attached or that the proper library is defined in the options file.


W8 - ISOGEN key is undefined in PDS - ISOGEN map. This message indicates that an entry in the PDS to ISOGEN symbol map exists for the PDS component but that the ISOGEN symbol name in the table does not. Make sure that the table contains the ISOGEN symbol name for the component in question. W9 - Could not locate item in PDS to ISOGEN symbol map. This message indicates that the PDS symbol in question could not be located in the PDS to ISOGEN symbol map. W10 - No-mto attribute has illegal value. The no-mto attribute on a component, pipe, or instrument has a value other than 0 or 1. Set the attribute to a legal value. W11 - Error forming nozzle note. An error has occurred forming the nozzle connection note generated at equipment nozzles. Check the label description library labels in the library if you are using the NOZZLE_NOTE table in the options file. Also review the nozzle entity to make sure that everything looks fine. If the failure occurs with the default nozzle note then report the problem to Intergraph. W12 - The coordinate system option is invalid. Coordinate system is set to PLANT. The coordinate system defined in the options file is incorrect so it was set to a default value. Check the option specified in the options file. W13 - Material description has been truncated. The material description generated from the material description library and the label description library has exceeded the maximum size allowed for in the software and was truncated. Contact Intergraph. W14 - Error reading Specialty Material Description Library. An error occurred retrieving the material description for a piping specialty, instrument or support from the specialty description library. An error message is generated in the iso bill-of-material. W15 - Error reading the Material Description Library. An error occurred retrieving the material description for a commodity item. An error message is generated in the iso bill-ofmaterial.

A - 10


W16 - Error attaching the design file . W17 - Error accessing A/N Commodity Library. An error has occurred searching the alphanumeric commodity library either for an implied material item or for a size dependent commodity code. Check the library to see whether or not the item that is being searched on exists. W20 - Header record attribute is undefined. Each entry in the PIPELINE_HEADER table in the options file defines a "Header record" for ISOGEN. These header records simply define the initial value for certain attributes at the start of the line (that is, spec name, insulation type, and so on). This message is warning you that for some header record defined in the PIPELINE_HEADER table the value for it from the database is undefined. You must either define the attribute in the database or remove the header record entry from the table. W23 - An error occurred while generating implied materials. Bolts, a gasket, or a weld will NOT be generated in the drawing and/or the mto neutral file. Some error resulted in no implied materials. Check the error message file for details of the problem. W25 - Error loading spec attributes for implied component. An error has occurred while attempting to overlay attributes from the spec for a stub onto the database record for a lap-joint flange. This overlaying must be performed just prior to generation of the material description so that attributes embedded in the material description for the stub can be generated properly. Make sure that the spec contains a valid entry for the stub. The spec search is performed by using the same data as for the lap joint flange except that the option code is set to the flange option code plus 5000. W26 - Maximum number of implied items exceeded. A component generates too many implied items from the Material Description Library and an internal buffer has overflowed. Contact Intergraph to have the buffer size increased. W27 - The Material Description Library is required in order to generate implied materials. Some materials might be missing from the MTO neutral file. A component indicates that implied material should be generated from the Material Description Library but the library is either not attached to the model or the library that is attached does not exist.


W28 - Error accessing the Material Description Library for implied materials. A component indicates that implied material should be generated from the Material Description Library but none was found. Check to make sure that the library contents are correct. W29 - Title block tables file not found. The title block tables file identified in the FILES section of the options file does not exist. This file identifies those attributes that are to be placed in the drawing title block. When this file does not exist no text can be placed in the title block. W30 - Error opening title block tables file. This message indicates that the title block tables file exists, but that for some reason it could not be opened. Check that your process has proper VMS access to the file. W31 - Error opening segment data file. File will not be created. The file holding title block attributes generated from the SEGMENT_DATA_TABLE (in the title block tables file) could not be opened. No title block data will be generated. W32 - Error opening STIB input file. File will not be created. The file holding title block attributes generated from the DRAWING_DATA_TABLE (in the title block tables file) could not be opened. No attributes generated by this table will appear in the title block. W33 - Error opening sheet specific title block data file. The file holding title block attributes generated from the SHEET_DATA_TABLE (in the title block tables file) could not be opened. No attributes generated by this table will appear in the title block. W34 - Error opening MTO Neutral File - file will not be created. A UNIX error occurred when creating a new mto neutral file. Make sure that your process has write access to the default directory. W35 - MTO record map not found. The mto record map, specified in the options file, cannot be located. Check the file spec in the options file and make sure that your process has read access to the file.

A - 12


W36 - Valve/Operator file does not exist. A valve/ operator table has been specified in the options file, but it could not be found while attempting to open it. W37 - Notes File not found. A Notes File has been specified in the options file, but it could not be located when an attempting to open it. W38 - Error opening the Notes Table. An error occurred while attempting to open the Notes Table. Make sure that your process has read access to the file. W39 - Notes Table lookup failed. A Notes Table record whose input matches the current one could not be located. The current key is printed out. Check the Notes Table to ensure that the input has a corresponding record. W40 - The number of components exceeds the limit of the maximum allowed number of components in a multiple bolt-through. W41 - Error retriving component from linkage. Cannot determine second orientation for operator. An error has occurred while scanning the design file for a valve operator that requires a second orientation. This is probably an Intergraph software problem. W42 - User Symbol Library not found. The user symbol library, specified in the options file, cannot be found or the current extraction process does not have privilege to access it. W43 - Bolt-thru component encountered at a loop closure W44 - The last start point is chosen to be the traversal start point The segment occurrence is different with that of the last start point Old - Table: 3 Component Occ: 4195082 Segment Occ: 4194661 New - Table: 3 Component Occ: 4195082 Segment Occ: 4194662


W45 - Error locating segment for logical pipe support W46 - Error computing pipe support orientation. An error occurred in the calculation to pipe support. The connect point orientations should be checked in graphics to confirm that they are correct. W47 - Detail sketch directory not found W48 - Detail Drawing definition file not found W49 - Weld Definition Format file not found W50 - Error retrieving weld numbers W51 - Very short pipe encountered W52 - Enclosure type is invalid W53 - Label: $1 in triangle box exceeds maximum length of two W54 - Label: $1 in diamond box exceeds maximum length of three W55 - Overlapping components were detected. Refer to the HITS report for details. W56 - Two end points match the last start point segment occurrence The end closest to the last start point is the chosen start point Old - Table: 3 Component Occ: 4195082 Segment Occ: 4194661 New - Table: 3 Component Occ: 4195334 Segment Occ: 4194661 W57 - Only one end point matches the last start point segment occurrence This end point is chosen to be the traversal start point Old - Table: 3 Component Occ: 4195082 Segment Occ: 4194661 New - Table: 3 Component Occ: 4195334 Segment Occ: 4194661

A - 14


W58 - No end point matches the last start point segment occurrence The end closest to the last start point is the chosen start point Old - Table: 3 Component Occ: 4195082 Segment Occ: 4194661 New - Table: 3 Component Occ: 4195334 Segment Occ: 4194661 W59 - Components from spool 1 on sheet 2 were deleted Refer to sheet 4 for the updated spool 3 W60 - Cannot access material listing definition file W61 - Intergraph option 15 is 0 Spool number generation will be based on ISOGEN switch 39 W62 - The last component on sheet 1 was added prior to this extraction Partition: 8 Table: 3 Occ: 32 120 W63 - Cannot access Bending Parameters file W64 - Error in rotation matrix for pipe support. Pipe support in Model attachment number . W65 - Error opening PDME neutral file. File will not be created. . W66 - No component was encountered. The start point will be referenced for Structural Dimension. W67 - FrameWork Ascii file not found in the project directory.


A.1.3 Error Messages __________________________________________________________________________________________________________________________________________________ E2 - Error reading type 63 element from design file. The primary model file (the first model file input) does not contain the proper type 63 elements. Check the file with EDG and/or attempt to work in it in graphics. E3 - Error opening input data file - pdsidf.dat. An error occurred when attempting to open the input file to the ISOGEN interface. Check to make sure that file pdsidf.dat exists in the default VMS directory. E4 - Error retrieving project information E5 -Invalid primary model file - file does not exist E6 - No valid model design file specified. Of the list of design files input to the ISOGEN interface none were considered valid. Refer to error messages generated previous to this one for more detail. E7 - Invalid extraction criteria is defined in Intergraph options block word 22. Valid values are 0 or 1. The extraction criteria defined in the options file INTERGRAPH_OPTIONS_BLOCK is invalid. Correct the options file. E8 - No extraction criteria defined. No extraction criteria specified in the input file to the ISOGEN interface was found to be valid. Correct the inputs for identification of the lines to extract. E9 - First header record must be a line name id (-6) record. Modify the PIPELINE_HEADER table in the extraction options file. The first entry in the PIPELINE_HEADER table in the options file must always be a -6 record for the line name or line id. Correct the table in the options file. E10 - Error opening intermediate data file. An error has occurred in creating an output file in the default directory. Make sure you have write access to it.

A - 16


E11 - Broken pipes exceed the maximum allowed 100 occurrences. There are more than 100 pipes broken with the branch weld or pipe support for the extracted pipeline. Reduce the number of pipes broken and contact Intergraph to get the maximum allowed broken pipes increased. E12 - Error retrieving type 63 elements. An error has occurred in retrieving the primary (first) model file type 63 elements. Check the file with EDG and make sure that you can work in the file in graphics. E13 - Error opening Standard Notes Library. An error has occurred in opening the standard notes library that is specified in the primary model file type 63 data. Check that the library is properly attached with the RDB software. E14 - Error opening spec database. An error has occurred initializing the spec database. Make sure that it is properly attached to the primary (first) model file using the RDB software. E15 - Number of connect points exceeded internal limit of 2000 connect points. The maximum number of connect points per extraction is 2000. Break the line into two separate line names and re-extract the line as two separate isometrics. E17 - Attempted to pop nonexistent tap stack entry. This message indicates an internal software problem that should be reported to Intergraph. When it does occur it should only be in connection with lines that contain tapped components. E18 - Internal stack limit exceeded. This message indicates an internal software problem that should be reported to Intergraph. When it does occur it should only be in connection with lines that contain tapped components. E19 - Error opening mto tables file. An error has occurred while trying to open the mto neutral file map that is specified in the options file. Check the file specification in the options file and make sure you have read access to the file.


E20 - Error reading mto tables file. An error has occurred while trying to read an entry in the mto neutral file map. Check that the table entries have the correct format. E21 - Error reading database occurrence. An error has occurred in trying to read a record from the database base on a design file linkage. This error indicates potentially serious problems in the model. It is strongly recommended that the model be analyzed to determine the extent of the problem and to correct the situation. E22 - Internal table lookup error for IDF record numbers. The record number taken from the PDS to ISOGEN symbol map for a component does not exist in an internal table. Check the PDS to ISOGEN symbol map to make sure that it contains only those record numbers allowed by ISOGEN. E23 - Environment variable ISOOPTION not defined or file does not exist E24 - Error opening ISOGEN options file. The options file exists but it could not be opened. Make sure that proper access to the file exists. E25 - Error reading iso extraction options file. An error has occurred while reading an entry in the options file. Make sure that options file entries have the proper format. If the return code is -998 then this error indicates that a options file table has exceeded the maximum allowable size. In this case you should reduce the number of table entries and contact Intergraph to get the table size increased. E26 - Error opening PDS to ISOGEN symbol map. An error has occurred while opening the PDS to ISOGEN symbol map. Check the options file entry to make sure that the file is properly specified. E27 - Error reading the PDS to ISOGEN symbol map - No valid entries defined in the table. The PDS to ISOGEN symbol was successfully read but no valid entries were found in the table. E28 - Error opening valve/operator file. An error has occurred while opening the valve / valve operator symbol map. Check the options file to make sure that the file is properly specified.

A - 18


E29 - Error reading size of valve/operator table. The first entry in the valve / valve operator table is a record that contains the number of rows and columns in the table. An error has occurred while attempting to read these values. Check that the format of the table is correct. E30 - Valve/operator table is too large. The valve / valve operator table is larger than the maximum currently allowed by the software. Reduce the table size and contact Intergraph to get the maximum size increased. E31 - Error reading valve/operator table values. An error has occurred while reading the body of the valve / valve operator table. This usually indicates that the table sizes defined in the first record of the file are incorrect. E32 - Error initializing the piping design database E33 - No components were found that match the database search criteria. Either the line name substrings or line ID’s that were specified in the input do not identify any lines that exist in the input model files. Check the inputs to make sure that they are correct and agree with the line name or attributes that make up the line id. E34 - Invalid node or path for iso design file E35 - Internal error generating material pointer. An internal software error has occurred in generating a material pointer for an olet type component. If the software were allowed to continue the bill-of-material would be generated incorrectly. Contact Intergraph if you receive this error. E36 - Internal error generating material pointer for downstream component. This error is the same as error number E35. E37 - Transformed coordinate exceeds the maximum. This error is caused from a coordinate that is too large to pass to ISOGEN. All coordinates are transformed to the output coordinate system (as controlled by the Intergraph options block) and then converted to 1/100’s of millimeters for ISOGEN. This value must fit within a 4 byte integer. This limitation results in a maximum coordinate value of 21,474 meters, or 70,450 feet or approximately 13.3 miles.


E38 - Internal error generating component item code. An error occurred while generating the item code for a stub (from a lap joint flange). Contact Intergraph if you get this error message. E39 - Error accessing spec for implied item. An occurred while attempting to read the spec database entry for a stub. Check that the entry exists in the database. The stub spec entry should have the same lookup parameters as the flange except that the option code should be the flange option code plus 5000. E41 - Error title block tables file E42 - Error opening project database E43 - Error reading database record E44 - Error reading database record E45 - Line is composed of multiple disconnected sections. This error results from trying to extract a pipeline that is either incomplete or incorrect and exists in the model in multiple unconnected pieces. It is not enough for all the segments to be connected. There must be components on top of the segments that are connected. E46 - Line does not contain a valid traversal start-point. This error occurs when the ISOGEN interface finds it impossible to obey ISOGEN rules for traversal of the pipeline network. The only work-around is to split the pipeline into two smaller sections and then extract the sections individually. E47 - Number of sections does not match specified value. For pipelines that are intentionally disconnected (for example, the line leaves the piping area, goes into the rack and then re-enters the area somewhere else) then you must specify the number of disconnected sections for the line in the Batch Data File. When the number of sections you specify does not match the number encountered in the model, this error occurs. Check the model to determine whether the Batch Data File or the model is incorrect. E48 - Invalid section number. Invalid inputs have been passed to the ISOGEN interface for multi-section pipelines in pdsidf.dat. Report this error to Intergraph.

A - 20


E49 - Component does not have an entry in the PDS to iso symbol map. (This error does not apply to ISOGEN.) E51 - Induction bend stack limit exceeded. An internal data structure overflowed while processing a line containing induction bends. Report this error to Intergraph. E52 - Error initializing DFPI Model number: $1 E53 - Error retrieving component from linkage: cannot determine cog for mto neutral file E54 - Error retrieving component from linkage: cannot process offset geometry component E55 - Error retrieving component from linkage: cannot process offset geometry component E56 - Error retrieving component from linkage: cannot process 180 degree turn E57 - Total number of segments exceeds the maximum number of segments E58 - Check the number of table entries specified against the actual number of table entries. Also, check the format of each table entry E59 - Error retrieving the graphic commodity library name E60 - Error initializing the piping project database E61 - Error accessing the standard note library name E62 - Error accessing the piping specification database name E63 - An internal table size limit has been exceeded E64 - No model was found with the specified discipline E65 - No components were found that match the database search criteria


E66 - Unable to locate component’s user data E67 - Error initializing the project database E68 - Error reading model $1 from the database E69 - Error mounting design file $1$2 E70 - Error reading the last traversal start point Section Number: 1 Drawing Index Number: 150 E71 - Line extends over the maximum limit of 256 design file. E72 - The chosen starting point is not the last traversal start point Stop extraction because Intergraph option 68 is set to 1 Old - Table: 3 Component Occ: 4195082 Segment Occ: 4194661 New - Table: 3 Component Occ: 4195334 Segment Occ: 4194661 E73 - Error opening piping job specification table library . E75 - Error updating symbol library. E76 - Error stroking elements to ascii file. E77 - Error locating drawing file. E78 - Error locating index file. E79 - Error locating library path. E80 - Error - $1 not found. E81 - Error - Drawing and Index file must be specified. E82 - Error - Drawing, Index and Library files must be specified. E83 - Extraction Failed: Possibly caused by Olet owned by branch.

A - 22


A.2 ISOGEN __________________________________________________________________________________________________________________________________________________ The error messages issued by ISOGEN (through IZOD2) are directed to two places. Errors issued by ISOGEN proper are directed to the ISOGEN message file. This file is either named in the options file or has the same name as the output iso file name with an extension of .msg. Errors generated by the Intergraph design file interface are directed to a file named IZOD2.ERR. When IZOD2 is run through the delivered command procedures then IZOD2.ERR is appended to any error message file created by the ISOGEN interface - pdsidf.

A.2.1 ISOGEN message file errors __________________________________________________________________________________________________________________________________________________ (35:2003) - WELD NUMBERS HAVE CAUSED DATA OVERFLOW An internal buffer for weld data has overflowed. Try a manual split of the pipeline into more sections. (35:2004) - INPUT DATA OVERFLOW The pipeline is too big. It must be extracted in smaller sections. (35:2005) - TEE OFF TEE GREATER THAN 20 DEEP This message indicates that the piping network being extracted contains branches which are too deeply nested for ISOGEN to handle. A branch off from the pipeline header is level 1. A branch off from the level 1 branch is level 2. A branch off from a level 2 branch is a level 3 branch. The maximum level branch that ISOGEN can handle is a level 20 branch. (35:2007) - TEE IN SKEW ISOGEN has detected an internal inconsistency. Check the resulting drawing. (35:2008) - DATA FAULT SKEW Same as 35:2007 (35:2009) - SKEW WITH NO CONTENTS Same as 35:2007


(35:2010) - FITTING WITH OFFSET NOT IN LINE WITH PIPE The offset of a fitting is not in line with an adjacent item. This is possibly a program or input data error. Check the resulting drawing. (35:2011) - ANGLE FAIL Unacceptable pipeline direction detected. This is possibly a program or input data error. Check the resulting drawing. (35:2012) - DATA FAULT ISOGEN detected a problem in some internal data. This is possibly a program or input data error. Check the resulting drawing. (35:2012) - DATA FAULT, DOUBLEBACK PIPE Occasionally, doubleback pipe errors can be erroneously generated. This occurs when the extracted pipeline and the grid line or structural column are located in the same place. In this case, there will be one dimension to the structural element and the FAIL message will appear on the face of the iso. This can occur regardless if the isometric extracts with no other errors. In the following graphic, pipeline and Grid Line 3 are coincident with one another. This is interpreted by the ISOGEN software as a pipeline that doubles back on itself which results in the FAIL message on the isometric drawing.

If the reference point on the pipe resides in the same plane as the structural component or grid line, a FAIL message will appear on the isometric and the .err file will report a doubleback pipe error. This error is a result of the manner in which the ISOGEN software interprets the .idf file and should be ignored.

A - 24


(35:2013) - DATA FAULT UP DOWN Same as 35:2012 (35:2014) - DATA FAULT EAST WEST Same as 35:2012 (35:2015) - DATA FAULT NORTH SOUTH Same as 35:2012 (35:2016) - DATA OVERFLOW, DRAWING REJECTED, TOO MUCH DATA, TRY SMALLER SPLIT Too much data is being put onto too small a sheet. Either insert some manual pipeline splits or use a larger paper size. (35:2017) - MESSAGE FAIL An error has occurred positioning messages on the drawing. This is caused by too many messages. Manually splitting the drawing might get around the problem. (35:2018) - SHAPE FAIL Drawing generation has failed. It might succeed if viewed from another direction. (35:2019) - DRAWING HEIGHT EXCEEDS ALLOWED 999 MM The maximum drawing height is 999 mm. (35:2020) - TOO MANY COORDINATES IN FITTINGS Too many user-defined fittings have caused an internal array to overflow. Reduce the size of the user symbol library. (35:2021) - TOO MANY FITTINGS Same as 35:2020. (35:2023) - WARNING, PAPER SIZE > A1 OR AD - THIS MAY PRODUCE UNACCEPTABLE RESULTS. Too large a paper size might result in unacceptable drawings.


(35:2025) - CHECK ISOGEN considers that the drawing layout requires checking to make sure that it is satisfactory. (35:2026) - FAIL ISOGEN considers that the drawing has failed in one of the stages of setting it up for plotting. (35:1001) - OVER 200 ALTERNATIVE TEXT RECS. FOLLOWING DATA IGNORED. MORE THAN 200 TEXT RECORDS - DEFAULT TABLE USED. ISOGEN allows a maximum of 200 ATEXT’s. Anything more will be ignored. (35:1002) Same as 35:1001. (35:1003) Same as 35:1001. (35:1004) - FITTING NOT FOUND - DEFAULT SHAPE USED A fitting shape key cannot be located. The non-category component is place of the one specified. (35:1009) - OVERFLOW IN DATA - PIPELINE REJECTED The pipeline is too big, causing an internal buffer to overflow. Manual splitting of the drawing or a larger sheet size might solve the problem. (35:1015) - INVALID ITEM/ DESCRIPTION POINTER An mto pointer in the intermediate data file points to an item that doesn’t exist. This is an Intergraph interface error. (35:1016) - ITEM CODE WIDTH ERROR - APPENDED TEXT LOST An item code is larger the value specified in the ISOGEN options block. (35:1018) - NO FITTING DETAILS EXIST FOR FITTING CODE An internal table lookup failed. This is an ISOGEN bug.

A - 26


(35:1019) - FITTINGS OVERLAP WHICH CANNOT BE CUT BACK Coordinates of adjacent components overlap and the fittings can be trimmed (that is, a flanged valve). (35:1020) - INSUFFICIENT LENGTH ON OVERLAPPING FITTINGS TO ALLOW CUTBACK Adjacent fittings which can be trimmed overlap, but not enough for the required cutback. (35:1021) - RUN ABORTED. THE WIDTH OR HEIGHT (EXCLUDING BORDERS, MATERIAL LIST, ETC) IS LESS THAN 50 MM. THIS IS NOT ENOUGH ROOM FOR THE ISOMETRIC. The drawing size is too small or the margins are too large. (35:1022) - THE MATERIAL CODE IS TOO WIDE AND HAS BEEN CHANGED FROM — TO — The material code has been trimmed to the maximum allowable length. (35:1026) - ERROR - UNABLE TO OPEN INTERMEDIATE DATA FILE Usually this indicates that you have forgotten to execute the ASCII to binary conversion program. The ASCII output generated by the ISOGEN interface must be converted to binary (using DATCON.COM) before executing IZOD2. (35:1027) - WARNING - ILLEGAL SCALE FACTOR FOUND FOR LINE FLOW ARROW - DEFAULT SCALE 8 USED The scale factor used for the pipeline flow arrow was set to an invalid value. (35:1029) - WARNING - NO POSITION GIVEN FOR RECORD ID. This message indicates an error in the ISOGEN interface. (35:1030) - ERROR - OVERFLOW IN TEXT POSITIONING ARRAY The maximum number of text positioning records has been exceeded in the intermediate data file. Reduce the number of drawing annotations. (35:1031) - ERROR - OVERFLOW IN PIPELINE HEADER ARRAY The maximum number of pipeline header attributes has been exceeded. Reduce the numbers of entries in the options file PIPELINE_HEADER_TABLE.


(35:1032) - WARNING - ONLY NEW FORMAT SPEC BREAK ALLOWED ON SYSTEM ISOMETRICS. SET SPEC BREAK SWITCH TO NEW FORMAT. The ISOGEN option controlling the spec break format must be set to 1. (35:1033) - ERROR - OVERFLOW IN PIPELINE HEADER DATA (PIPELINE REJECTED) An internal array holding pipeline header data has overflowed. (35:1034) - ERROR - OVERFLOW IN USER DEFINED SPOOL NAME ARRAY Too many spools have been defined in the isometric. (35:1035) - WARNING - USER DEFINED SPOOL NAME EXCEEDS MAX OF 30 ONLY FIRST 30 WILL BE OUTPUT AT FRAME POSITION. A user defined spool name is too large. (35:1036) - WARNING - USER PREFIXED SPOOL NAME EXCEEDS MAX OF 30 ONLY FIRST 30 WILL BE OUTPUT AT FRAME POSITION. A user prefixed spool name is too large. (35:1037) - ERROR - OVERFLOW IN PIPELINE HEADER DATA ON SYSTEM ISO A system isometric is composed of too many pipelines. (35:1038) - WARNING - USER DEFINED FITTING NEW KEY ALREADY EXISTS OLD SHAPE USED. The new shape key (skey) for a user defined symbol already exists within ISOGEN. Another symbol name must be chosen. (35:1039) - ERROR - USER DEFINED FITTING OLD KEY NOT FOUND The old shape key (skey) for a user defined symbol does not exist. An existing symbol key must be used for the old skey. (35:1040) - ERROR - USER DEFINED FITTING OLD KEY NOT SET A user defined symbol does not have an old shape key (skey) defined for it. User defined symbols must have an old or existing shape key as part of the definition of the new symbol.

A - 28


(35:1041) - WARNING - USER DEFINED FITTING SPINDLE KEY NOT FOUND The spindle key specified for a user defined ISOGEN fitting cannot be found. (35:1042) - ERROR - OVERFLOW IN USER DEFINED FITTING ARRAY An internal buffer has overflowed due to too many user defined components. (35:1043) - ERROR - OVERFLOW IN FITTING SHAPE ARRAY An internal buffer has overflowed due to too many user defined symbols. (35:1044) - WARNING - OVERFLOW IN USER POSITIONED TABLE FOR RECORD ID An internal buffer has overflowed due to too many user positioned title block records. (35:1045) - ERROR - USER TEXT POSITIONED OUTSIDE DRAWING FOR RECORD ID - TEXT OUTPUT AT DRAWING ORIGIN. Bad user defined text coordinates have been specified. (35:1048) - WARNING - ONLY 30 CHARACTERS ALLOWED IN PIPELINE NAME ON CUT PIPE SUMMARY. The pipeline name in the cut pipe summary report can not exceed 30 characters. (35:1052) - WARNING - OVERFLOW IN CUT PIPE REPORT ARRAY, ONLY 2000 ENTRIES ALLOWED. The maximum cut pipe report size has been exceeded. (35:1053) - WARNING - OVERFLOW IN USER DEFINED OFFSET FITTINGS, ONLY 100 ENTRIES ALLOWED. The maximum of 100 user defined offset fittings has been exceeded. (35:1054) - WARNING - INSTRUMENT NAME RESTRICTED TO TWO LINES. Instrument tag numbers are restricted to two lines. (35:1055) - WARNING - INSTRUMENT NAME EXCEEDS BALLOON SIZE. An instrument tag number is larger than the balloon size specified in the ISOGEN options block.


(35:1056) - ERROR - UNABLE TO OPEN USER FITTING FILE ISOGEN is unable to open the user defined symbol library. Check that the file exists and that ISOGEN has read access to it. (35:1057) - ERROR - UNABLE TO POSITION SUPPORT/COMMENTS FROM COORDINATES GIVEN - ATTA HAS NOT BEEN DIMENSIONED, CHECK POSITION ON DRAWING. ISOGEN was unable to position a pipe support and its comment. (35:1058) - WARNING - SPLIT POINT POSITIONED AT LINE/BRANCH END SPLIT POINT IGNORED. A user defined split point was placed at an endpoint of the pipeline. (35:1059) - WARNING - SPLIT POINT HAS BEEN POSITIONED INCORRECTLY SPLIT POINT HAS BEEN REPOSITIONED. ISOGEN has rejected a user defined split point and repositioned it. (35:1060) - WARNING - TAP OFF POINT CONNECTED TO STANDARD FITTING TAP OFF SHOWN FROM FITTING CENTER. A tap is called for on a fitting that is not user defined. The tap point is taken to be the center of the fitting. (35:1061) - WARNING - NO DIRECTION GIVEN FOR UNDEVELOPED FITTING TAP - DIRECTION ASSUMED FROM FITTING COORDINATES. ISOGEN cannot determine a direction of a fitting tap. A default direction is assumed. Cut lengths have been suppressed for pipe not in the material list, check isometric drawing. (35:1062) - WARNING - PIPE CONFLICT (PIPE ON/OFF MATERIAL LIST) - CHECK CUT LIST. ISOGEN is unable to position comments using the given coordinates. () (NEW) - WARNING - BATCH INPUT FILE CREATED WITH EARLIER VERSION OF PD_ISO BATCH INPUT FILE VERSION: BATCH DATA VER 4.0 Iso types are not represented in a batch input file created prior to PD_ISO version 5.00.00.05. You should recreate all batch input files using a PD_ISO version greater than 5.00.00.05.

A - 30


(35:1099) (New) - ERROR - UNABLE TO POSITION COMMENT USING COORDINATES GIVEN COMMENT RECORD CO-ORDS ARE ***** ***** ***** CHECK LOCATION OF COMMENT ON DRAWING ISOGEN is unable to position ’skey’ using the given coordinates. (35:1101) (New) - ERROR - UNABLE TO POSITION ’skey’ USING CO-ORDINATES GIVEN ’skey’ RECORD CO-ORDS ARE ***** ***** ***** CHECK POSITION ON DRAWING ISOGEN has received an unacceptable position for ’skey’ symbol. (35:1104) (New) - ERROR - UNACCEPTABLE POSITION FOR ’skey’ SYMBOL ’skey’ RECORD CO-ORDS ARE ***** ***** ***** SYMBOL NOT ON DRAWING


A.2.2 Design File Interface Error Messages __________________________________________________________________________________________________________________________________________________ E1 - Error opening IZOD2 error file For some reason the error file created by the design file interface could not be opened. Check to make sure that you have write access to the current default directory. E2 - Logical name ISOSEED is not defined or the iso seed file does not exist This error message can only be generated when a wildcard character is used in the output design file name. When this is the case then IZOD2 copies the seed file itself for each sheet that is generated. If the logical name is not defined or the file does not exist then the file cannot be copied. E3 - Iso design file not found This error message is issued when the output design file cannot be found. It can only be issued when the output design file name does not contain a wildcard character. In this case the output file must be created prior to executing IZOD2. E5 - Error opening the isometric design file An error has occurred in opening the output iso design file for block i/o. Verify that the file is not already open, that you have write access to the file and that the file is a design file. E6 - Error creating new iso design file An error has occurred in copying the seed iso file to a new iso design file. This error can only be issued when the output iso file name contains a wild card character. E8 - Error opening the isometric design file This message is the same as E5, except that it is only issued when the iso design file name contains a wild card character. E9 - Error writing graphics to design file This message indicates that a write operation to the design file could not be completed successfully.

A - 32


A.3 Batch Extraction Software Error Messages __________________________________________________________________________________________________________________________________________________ The following error codes may be reported in the batch extraction log file: 1 - Cannot Mount Batch Input File When this error is encountered, verify the following: 1.

Check if the Node/path/file exists.

2.

Find out if the remote node is up.

3.

Check if the /etc/exports file of the remote node contains the path to be mounted.

2 - Error Initializing Project DBS Verify that you have access the Database Server. 3 - Error Initializing Piping DBS Verify that you have access the Database Server. 4 - Error Initializing Job Spec DBS Verify that you have access the Database Server. 5 - Error Reading Project Options (Default Set) System was trying to read the Project Options from the database server. 6 - Error Mounting Working Directory Probable Reason: 1.


2.


3.

Check if the /etc/exports file of the remote node contain the path to be mounted.


7 - Error Changing To Working Directory Check Your directory privileges. 8 - Error Creating Temp Sub-Directory in Check Your directory privileges. 9 - Error Opening Batch Input file An error occurred when the batch command procedure attempted to open the batch job input file. Make sure that the file protections on the file are such that the command procedure can open the file. 10 - Record Too Long In Batch Input File See the log files for the specific record (line) is causing the problem. 11 - Batch Input File Version Invalid: The batch input file was created with a previous software version and the format is no longer valid. 12 - Error Reading Batch Input File An error has occurred reading a record from the batch job input file. Look in the batch log file to determine the cause of the problem. 13 - Error Writing To Batch Input File The command procedure does not have write access to the output file directory that was specified by the selected default set. The process under which batch iso’s are executing must have write access to the output file directory. The line may have been successfully processed. See the log files to verify successful processing. 14 - Invalid Default Set Line In Batch Input file Refer to the logs file to determine cause of this problem. 15 - Error Changing To Master Work Directory Check Batch Login privileges for write access to the /usr/tmp directory.

A - 34


16 - Work Directory: Check Batch Login privileges for write access to the /usr/tmp directory. 17 - Error Changing To Working Sub-directory Check Batch Login privileges for write access to the /usr/tmp directory. 18 - Cannot Mount Output Iso Directory (ISOPATH) Most common reasons for this error: 1.


2.


3.


Also,for interactive extraction, verify that the Environment variable ISOPATH, in control.sh is set to a valid directory. 19 - Error Moving To Output ISO Directory Check Batch Login privileges for write access to the output path specified by the selected default set. 20 - Error Changing To Directory Check Batch Login privileges for write access to the /usr/tmp directory. 21 - Error Deleting Temp Sub-Directory Check Batch Login privileges for write access to the /usr/tmp directory. 22 - Error Renaming pdsidf.dat Or pdsidf.err One or both of these files could not be renamed to isoname.dat or isoname.err. 23 - Error Starting ’Iso Interface’ Process When this error is encountered, check the following: 1.

Verify that the ISO software has been downloaded by keying in dates PD_ISO at the UNIX prompt.

2.

Verify that there are not too many process running on the workstation.

3.

Verify that the system has enough memory.


24 - Error Returned From batch.sh See the log files for more information. 25 - Error Copying/Adding To pdsidf.dat The command procedure does not have write access to the output file directory specified in the selected default set. The process under which batch iso’s is executing must have write access to the output file directory. 26 - Error Opening/Reading/Closing sheets.tmp An error has occurred reading a record from the batch job input file. Look in the batch log file to determine the cause of the problem. 27 - Invalid Options String Check the default set through ’Revise Default Set’. There might have been an error setting up the Default Set when it was first defined. 28 - Error Writing To Batch Log The command procedure does not have write access to the output file directory specified in the selected default set. The process under which batch iso’s is executing must have write access to the output file directory. 29 - Error Opening/Closing Batch Log An error has occurred reading a record from the batch job input file. Look in the batch log file to determine the cause of the problem. 30 - MTO File Name > 14 characters Filename in Unix are limited to 14 characters 31 - Fatal Error In batch.sh When this error is encountered, check the following: 1.

Verify that the ISO software has been downloaded.

2.


3.


A - 36


32 - Unable To Obtain Local Node Name Check to see if the workstation’s node name has been correctly set up. Consult your system administrator. 33 - Error Creating Directory In Check Batch Login privileges for write access to the /usr/tmp directory. 34 - Unable To Save Previous Files In Check Batch Login privileges for write access to the /usr/tmp directory. 35 - Unable To Create Error Directory Check Batch Login privileges for write access to the /usr/tmp directory. 36 - Unable To Save In Error Directory Check Batch Login privileges for write access to the /usr/tmp directory. 37 - Serious Interface Error Refer to the log files to determine the cause of the problem. The Problem Line should be run with Debug & Verify turned on. Contact Intergraph system support and send them all of the generated files. 38 - Error Returning From ’Iso Interface’ See the log files for more information. 39 - Iso Interface - Abnormal Exit (Unix Error): Due To Signal This is a UNIX internal error. Check the Unix Signal returned error code to determine the problem. 40 - Batch.sh - Abnormal Exit (Unix Error): Due To Signal This is a UNIX internal error. Check the Unix Signal returned error code to determine the problem. 41 - Batch.sh - returned invalid error code The ksh has detected a possible UNIX error.


42 - Error Starting batch.sh This error is usually caused by either a memory or input/output problem. When this error is encountered, check the following: 1.


2.


3.


43 - Error in starting (exec call) batch.sh The batch.sh cannot be found. Verify that the PD_ISO environment variable in the control.sh has beed defined properly. This file should be located in /usr#/ip32/pdiso/bin. 45 - Project Name Format Invalid In Batch Input file Check if the Project Name in Batch Input File is present or a valid one. 46 - Error In Executing Ksh Command An error occurred when starting another process. When this error is encountered, check the following: 1.


2.


3.


48 - Run Aborted - Job Log May Have More Info See the log files for more information. 49 - Problem Line Not Processed After Restart of Iso Interface There was a problem with a line. The Iso Interface was re-executed to avoid a crash, the problem line was not processed after restarting the Iso Interface 50 - Error in calling system An error occurred when starting another process. When this error is encountered, check the following: 1.


A - 38


2.


3.


51 - Could Not Open pdsidf.dat An error has occurred reading a record from the batch job input file. First, verify that the file exists. If the file exists, look in the batch log file to determine the cause of the problem. 52 - Could Not Open seed.dat An error has occurred reading a record from the batch job input file. First, verify that the file exists. If the file exists, look in the batch log file to determine the cause of the problem. 53 - Area Not Found In Project When this error is encountered, verify that: 1.

the database server is running.

2.

the area name has been altered in the batch input file.

3.

the project area was not deleted before the batch job was submitted.

54 - Area/Line Not Found In ISO Database When this error is encountered, verify that: 1.


2.

the line ID has not been altered in the Batch Input file.

3.

the line was not deleted before the batch job was submitted.

55 - No Model Found for Area When this error is encountered, verify that: 1.


2.

the model name has not been altered in the Batch Input file.

3.

the model was not deleted before the batch job was submitted.


56 - Project Defaults Not Set When this error is encountered, verify that: 1.


2.

the default set name has not been altered in the Batch Input file.

3.

the default set was not deleted before the batch job was submitted.

57 - Error Reading Project Option File Names When this error is encountered, verify that: 1.


2.


3.


58 - Cannot Close File An error, possibly a UNIX error, was encountered in closing a file. 59 - Unable To Process Area/Line Refer to the log files for more detailed information. 60 - Error Reading Drawing Revision Records When this error is encountered, verify that: 1.


2.

the line ID has not been altered in the Batch Input file.

3.

the line ID name was not deleted before the batch job was submitted.

61 - Error Updating Drawing Record Verify that the database server is running. 62 - Defaults Set Not Found When this error is encountered, verify that: 1.


2.


A - 40


3.


64 - Error Updating Drawing Revision Record Verify that the database server is running. 65 - Error Writing to file The command procedure does not have write access to the output file directory specified in the selected default set. The process under which batch iso’s is executing must have write access to the output file directory. 66 - Error Mounting Iso Seed Design File (ISOSEED) When this error is encountered, verify the following: 1.


2.


3.


68 - Error Initializing Microstation message The First Design File in the Current Area being processed could not be initialized by Microstation. 69 - Error Mounting Iso Plot File (ISOPLOT) When this error is encountered, verify the following: 1.


2.


3.


70 - Error Exporting Environment Variable Unix Error: check the amount of available workstation memory. 71 - Error Mounting Output Directory When this error is encountered, verify the following: 1.


2.



3.


72 - Error Mounting Border File (ISOBORDER) When this error is encountered, verify the following: 1.


2.


3.


73 - Unexpected Error From JOBCTL An error has occurred in creating input for the ISOGEN interface using data from the batch job input file. This error should only occur if the batch job input file is out of sync with the Batch Data File. The two files can get out of sync if lines are deleted after they have been added to a batch job input file. 75 - Abnormal Database Error (See System Log) See the Log files for more information. 99 - Fatal Error while running the Batch Job: batch.sh See the Log files for more information. 101 - Intermediate File Does Not Exist A fatal error has occurred in the generating the intermediate file from the ISOGEN interface. Look in the error log produced by the interface to determine the cause of the problem. 102 - Error Generating Binary IDF File An error has occurred in converting the intermediate data file produced by the ISOGEN interface to binary. This usually indicates an earlier problem in the ISOGEN interface. Look at the error log produced by the interface to determine the cause of the problem. 103 - Isometric Seed File Does Not Exist The isometric seed file specified in the Batch Data File does not exist. Either create the seed file or change the file specification in the Batch Data File.

A - 42


104 - Error Running ISOGEN Interface (ISOGEN) A fatal error running ISOGEN has occurred. Look at the error log produced by the ISOGEN interface and also at the ISOGEN message file. Error messages generated by the Intergraph design file interface will be written to the error log. Error messages generated by ISOGEN will be written to the message file. 110 - Error Splitting The MTO Neutral File When the ISOGEN interface produces an mto neutral file, the batch software automatically splits it into several files, each containing the mto data for a single sheet. This error is generated when splitting up the neutral file fails. Make sure that your MTO record map maps component occurrence numbers into the neutral file. 115 - Error Generating Title Block Text An error has occurred while attempting to determine which segment attributes should be placed in the title block of each isometric sheet. Make sure that you have properly set your Title Block Table File. Contact Intergraph for help if you cannot solve the problem. 120 - Iso Sheets File Not Found or Unreadable An error occurred when the batch command procedure tried to open the file that contains the number of isometric sheets generated by ISOGEN. This error indicates an Intergraph software problem. 121 - Error Reading Iso Sheets File An error occurred while trying to read the number of iso sheets from a file produced by ISOGEN. This error indicates an Intergraph software problem. 122 - Error Updating Number Of Sheets Error updating number of sheets An error occurred while updating the number of drawing sheets for a multi-section pipeline. Refer to the batch (DCL) log file to determine the cause of the problem. 123 - Error Opening STIB Input File An error occurred while trying to create an input file for STIB. This error probably indicates an Intergraph software error. 124 - Error Filling Out Title Block By STIB An error has occurred while STIB was attempting to fill out the drawing title block. Make sure that your seed iso design file has plenty of space for both the drawing graphics and the text that is inserted by STIB. Also make sure that the disk holding the batch run directory has plenty of contiguous space. STIB creates a 500 block temporary work file that must be contiguous.


125 - Error Getting Previous Manual Details An error occurred while attempting to move manual details from a previous version of a drawing to the latest. Refer to the batch (DCL) log file to determine the cause of the problem. 130 - Plot Software Does Not Exist Could not find the Plot Software (IP_IPLOT). If the plotting software is not loaded, set the plot option to No and rerun the iso. If attempting to perform a batch process, this error could also indicate that you do not have access to the requested queue. Verify that the requested queue name is available to the processing node’s batch login. 131 - Plot Seed File Does Not Exist The isometric seed file specified in the Batch Data File does not exist. Either create the seed file or change the file specification in the Batch Data File. 132 - Error Opening Or Writing Plot Job File An error has occurred creating a command procedure to launch an IPLOT plot job. This error is probably due to an Intergraph software problem. Refer to the batch (DCL) log file to determine the cause. Error occurred while creating the Plot Meta File: Check if there is enough memory space. 133 - Error Generating Plot Meta File Error occurred while creating the Plot Meta File. Verify that the system has enough memory. 134 - Error Submitting A Job To ISO_PLOT An error occurred submitting a job to launch an IPLOT plot. Make sure that the plot queue ISO_PLOT is properly set up. 135 - Batch Submitting Error Code: 0x10000XXX An error has occurred in submitting a batch job where XXX is an error return code listed in the ˜0batch0batchapi0batchapi.h file. For example, the return code 0x10000025 is defined as BATCH_ERROR_NO_ACCOUNT_MAPPING (025) IN THE ntbatchapi.h file. In this case, you would verify that your account is mapped correctly in the Intergraph Batch Manager. If the account password has been changed and the password in Account Mapping has not been updated since the account was mapped to the valid user, the batch job will still be reported as, Batch Job Submitted Successfully. The invalid password is not be detected by NTBATCH until the batch job is started.

A - 44


Appendix B: Alias ISOGEN Tables B-1

Appendix B Alias ISOGEN Tables

B-2 - PDS ISOGEN Reference Guide - August 1999


Tables of Intermediate File Records Record ID. No.

Purpose

-1

Overflow text record (Used with all types of text records)

-3 -4

Text for Isometric Title Block Special key input (That is, in-line items given a -4 key is treated in the special way that Alias instruments are.) Spare Pipeline Reference Spare Revision Identifier Project Identification (Code Number) Batch Reference (Zone Name) Piping Specification Name Nominal Pressure Rating (Class) Line Type Identifier Date of Data Transfer Insulation Specification Tracing Specification Painting Specification Spare Spare Item Code Item Description Tag Number and Hanger Name Hanger Tail Reference (ATTA CREF) Spare New Pipeline Reference (Used to indicate start of new pipeline on multi-pipeline plot.) Specification Change Identifier

-5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 -23 -24 -25 -26

Remarks

Pipeline Header Information


Tables of Intermediate File Records Record ID. No. -27 -28 -29 -30 -31 -32 -33 -34 -35 -36

-37 -38 -39 -40

Purpose Spare Spare Spare Connection Comment - Continued ON Connection Comment - Connected TO HCON/TCON = OPEN (Not used by PDS) HCON/TCON = CLOS End Connection Type (such as a cap, blind plug, etc.) HCON = VENT (Not used by PDS) HCON = DRAN (Not used by PDS) Unset HREF or IREF Indicator (But only when HCON or TCON is not set to OPEN, CLOS, VENT, DRAN or SCRD) -36 is used to disable “No Connection ...” notes from being displayed. (See also Intergraph Option 6) Comment on spool, fitting, or hanger Drawing Split Point Indicator ( + + + + ) Spare Skewed spindle directions or skewed ecc reducer flat directions

-51 -52 -53 -54 -55 -56 -57 -58 -59 -60

-67 -80 to -90 -100 -101 -102 -103 -104 -105 -106 -107 -108

Remarks

This block (-51 to -60) is reserved for internal Isodat processing.

Intergraph Weld Number Record Key User-defined Bill of Material Records Intermediate data transfer file name Schema plot file name (For drug frame) Isometric plot file prefix New/alternative symbol file names Material Control file name Message file name (Error and plot confirmation messages) PDMS error system file name (This is not user-definable) PDMS > ISOGEN (This is not user-definable) Printed Parts List file name


Tables of Intermediate File Records Record ID. No. -109 to -200 -201 -500 -501 -502

Purpose Spare

Reserved for ATEX - foreign language or other alternative text on isometric (Title Information, End Conditions, etc.) (Full details are available on a separate list) Reserved for new or alternative to fitting shape definitions. (Full details to be provided later.)

Remarks


Record Identification Numbers Spool and In-Line Fitting Records Please refer to Appendix E, ISOGEN SKEY Dimensions, for further details. Spool / Fitting Type

Record ID Numbers

Remarks

In Leg

First Branch Leg

Second Branch Leg

Out Leg

Bend Elbow O’let Tee Cross Reducer (Con/Ecc) Tee Reducer (Con/Ecc) Reducing Flange Tee Bend/Elbow Angle Valve 3 Way Valve 4 Way Valve Instrument

30 35 40 45 50 55 60 65 70 75 80 85 90

41 46 51 61 71 81 86 91

52 87 92

31 36 42 47 53 62 72 76 82 88 93

Pcom (Misc. Pipe Component) Pipe (Tube) Fixed Length Pipe Pipe Block (Fixed Length) Pipe Block (Variable Length) Flange Lap Joint Stub End Blank Flange (Blind) Gasket Bolt Weld Cap Coupling Union Valve Trap Vent

95

-

-

96

100 101 102

-

-

-

103

-

-

-

105 106 107 110 115 120 125 126 127 130 132 134

-

-

-

Plus a 0 record Plus a 0 record Plus a 0 record Plus a 0 record Plus a 0 record Plus a 0 record Plus a 0 record Plus a 0 record Plus a 0 record A straight through type instrument only has 90 & 93 record ID Numbers. Instrument Dials only have a 90 record.


Spool and In-Line Fitting Records (continued) Spool / Fitting Type

Filter User Positioned Comment Pipe Hanger/Support

Bore Record End of File Marker

Record ID Numbers

Remarks

In Leg

First Branch Leg

Second Branch Leg

Out Leg

136 149

-

-

-

150 180 to 199 inc. 0 999

-

-

-

-

-

-

Used to define position

Reserved for internal ISODAT processing


Option Switches This is a brief summary of the option switches operated by the 140-word options block. Recommended default values for each option are shown, together with either a list of alternatives or an indication of appropriate data values. Full details (where appropriate) can be found in Chapters 3 or 4. Any standard settings (Std. is =) indicated on the following pages are default settings from Alias; these settings are required to produce a ’STANDARD’ isometric drawing. You can make various alternative settings to meet specific project requirements. For any switch with multiple switch settings−such as A, B, C, D, E−the switches read from right to left, as shown below. Leading 0s (zeros) can be omitted, but trailing 0s must be included.


Option Switches Isometric Facility

Word Number

Switch Position

File Marker or Data

Cutting List

2

A

0

Suppress cut pipe list and cut pipe numbers. (default)

1

Generate cut piece numbers and a cut pipe list.

2

Cut piece numbers start at 1 on each sheet.

0

Use old style (limited information) cut piece list. (default)

1

Use new style (full information) cut piece list.

0

Generate numeric cut piece identifiers. (default)

B

C

Parameter Value Options

Generate alphabetic cut piece identifiers. 1 Generate standard cut lengths only. (default) D

0 1

Cut Marks

Character Size (Only controls text on isometric drawing)

3

4

0

Generate supplementary output of cut lengths in decimal inches format in the REMARKS column of the new style cut piece list. This setting only applies when using Imperial Units. Std. is = 0 for no cut marks. or set:

1

For plotted cut marks. (Position relative to drawing frame to be based upon margin dimension.)

0

For characters 2.5 mm high (default setting).

1

For characters 2.1 mm high.

2


3


4


5



Option Switches (continued) Isometric Facility Suppress Output Of End Coordinates

Date in Title Block

Word Number

Switch Position

5

6

A

File Marker or Data


0

Std. = 0 for normal end coordinates to be output for -30 to -36 type records.

data

Optionally set each of the 7 digits in the word to 1 or 0 for selective output or suppression of the end coordinates. 1101101 = suppress all end coordinates except for the -31 and –34 types records.

0

Std. is = 0 for date plotted in the form 14 APR 88.

1

EUR for date plotted in the format: 14/04/88

2

USA for date plotted in the format: 04/14/88

3

For no plotted date.

B

0 1

Use the date from the IDF file record (-14). Use the computer system date (taken at run time).

C

0 1

Output 2-digit year. Output 4-digit year.


Option Switches (continued) Isometric Facility

Word Number

Dimension Line Standout Distance

8

Switch Position

File Marker or Data


Data < 11

Default to use Standard Dimension Line Standouts (see below). Only used if options 40 and 118 are not set

Data ≥ 11

Where a value is set to the required basic standout distance in whole mm’s. Standard Dimension Line Standouts: For SMALL drawing text, set ISOGEN Word 4 to 1. A) String/Composite Dimension Standout = 12mm. B) Messages/Support & Reference Dimension Standout = 6mm C) Overall Dimension Standout = 18mm For MEDIUM text, set Word 4 to 0. A) String/Composite Dimen. Standout = 14mm. B) Messages/Support & Reference Dimension Standout = 7mm C) Overall Dimension Standout = 21mm For LARGE text, set ISOGEN Word 4 to 2. A) String/Composite Dimen. Standout = 16mm. B) Messages/Support & Reference Dimension Standout = 8mm C) Overall Dimension Standout = 24mm For EXTRA LARGE text, set Word 4 to 3. A) String/Composite Dimen. Standout = 18mm. B) Messages/Support & Reference Dimension Standout = 9mm C) Overall Dimension Standout = 27mm For EXTRA LARGE text, set Word 4 to 4. A) String/Composite Dimen. Standout = 20mm. B) Messages/Support & Reference Dimen. Standout = 10mm C) Overall Dimen. Standout = 30mm For EXTRA LARGE text, set Word 4 to 5. A) String/Composite Dimen. Standout = 22mm. B) Messages/Support & Reference Dimension Standout = 11mm C) Overall Dimension Standout = 33mm



Word Number

Switch Position

File Marker or Data

Dimension Line Standout Distance (continued)

Parameter Value Options For EXTRA LARGE text, set Word 4 to 3. A) String/Composite Dimen. Standout = 18mm. B) Messages/Support & Reference Dimension Standout = 9mm C) Overall Dimension Standout = 27mm For EXTRA LARGE text, set Word 4 to 4. A) String/Composite Dimen. Standout = 20mm. B) Messages/Support & Reference Dimen. Standout = 10mm C) Overall Dimen. Standout = 30mm

Dimensions On Drawing

9

A

B

C

0

For EXTRA LARGE text, set Word 4 to 5. A) String/Composite Dimen. Standout = 22mm. B) Messages/Support & Reference Dimension Standout = 11mm C) Overall Dimension Standout = 33mm Std. is = 0 for isometric with dimensions.

1

For isometric without any dimensions.

2

For Support dimensions only.

3

For COMPOSITE dimensions.

4

FULL STRING dimensioning, ALL components dimensioned

0

Do not include gasket thickness in flanged component dimension

1

Include gasket thickness in flanged component dimension.

0

Dimension displayed in a broken dimension line.

1

USA-style dimensioning, dimension displayed above dimension line.


Option Switches (continued) Isometric Facility Drawing Margin

Word Number 10

Switch Position

File Marker or Data


5

Std. is = 5 mm for left hand margin dimension. or set:

data 11

5

data 12

5

data 13

5

data Drawing Size

14

Alternative value for left margin. Std. is = 5 mm for right hand margin dimension. or set: Alternative value for right margin. Std. is = 5 mm for top margin dimension. or set: Alternative value for top margin. Std. is = 5 mm for bottom margin dimension. or set: Alternative value for bottom margin.

2

Std. is = A2 paper size (420 x 594 mm) Or set:

1

For A1 paper size (594 x 841 mm)

3

For A3 paper size (297 x 420 mm)

4

For A4 paper size (210 x 297 mm) Or set:

5

For AD paper size (22” x 34”)

6

For AC paper size (17” x 22”)

7

For AB paper size (11”x17”)

8

For AA paper size (8.5” x 11”)

9

For AE size drawings (33” x 44”)

10

For AO size drawings (841 mm x 1189 mm) Or set:

15

data

New value for drawing height in mms

16

data

New value for drawing width in mms



Word Number

Flow Arrows

17

Frame Control

Falling Lines (Slope)

Sloping Pipeline Indication Limit

18

Switch Position

File Marker or Data


0

Std. is = 0 for fluid flow arrows on selected in-line components. or set:

1

To suppress fluid flow arrows.

0

Std. is = 0 for standard Isoplot drawing frame. or set:

1

To suppress standard Isoplot drawing frame.

19

20

Used to control how falling sections of pipeline are actually to be defined on the iso. 0

Std. is = 0 to define falling sections of pipeline in terms of an angle (i.e., FALL 1.5°. or set:

1

To define falling sections in terms of a falls ration (i.e., FALL 1:60).

2

To define falling sections in terms of a falls percentage (i.e., FALL 1.7%).

3

To define falling sections in terms of grads (i.e., FALL 1 GRAD).

4

To define falling sections in terms of an incline (i.e., FALL 3/16’ PER FT).

5

To define falling sections in terms of an incline (i.e., FALL 16 MM PER M).

6

To suppress falling line indication.

5

Used to define the falls definition cut off point (i.e., to control what degree of steepness should be treated as a fall and what should not). In this case, the section concerned is surrounded by the normal box enclosure.

data

Std. is = 5 degrees or ratio of 1:11 or 9 percent or 5 gradients or 1" per ft (Imperial) or 88 mm per meter depending upon which key word is set as the first parameter. (All these are approx. = to 5 degrees.) or set:


Option Switches (continued) Isometric Facility Sloping Pipeline Indication Limit (continued)

Word Number

Switch Position

20

File Marker or Data


data

To the required value for the desired cut-off value of the previous switch (19). If the correct parameter for Switch 19 is set then:For 9 degree. cut-off, enter 9. For 1:6 cut-off, enter 6. For 16% cut-off, enter 16. For 10 grad. cut-off, enter 10. For 2" per foot cut-off, enter 2. For 166 mm per cut-off, enter 166. NOTE: The default cut-off value is 5 degree or its equivalent as indicated above.

Isometric Type

Loose Flange And Field Fit Weld Allowance

21

0

Std. is = 0 for combined isometrics (Fab and Erec information.). or set:

1

For Erection isometrics only.

2

For Fabrication isometrics only.

6

For individual Spool isometrics.

7

For no isometrics from an ISOGEN run.

22

Used to control the amount of extra pipe that is added to both the Cut Length dimensions and the Material List at Loose Flange and Field Fit Weld (FFW) positions. NOTE: Intergraph Option Switch 62 (Weld Number Display), position C, must be set to 1 for ISOGEN 22 to work properly. A/B/C

data

Value used for field welds Standard is 150 mm. Values are in mm.

D/E.F

data

Value used for offshore welds Standard is 0 mm. Values are in mm.



Word Number

Plotted Material List Control

23

Switch Position

File Marker or Data

Parameter Value Options This option allows control of the material list on the iso and the style of the material control file. (Material control file generation controlled by Intergraph Option 1.)

A

B

C

D

0

Material list plotted

1

Material list not plotted

Blank or 0 1

This is a sorted STYLE 1 list. Individual part numbers and Pulled Bends are given a ‘U’ number . (See ATEXT -356) Gaskets and Bolts are accumulated. Welds are given W or B numbers. (See ATEXT -357 & 358)

2

This is a sorted STYLE 2 list . Individual part numbers and Pulled Bends are given a ‘U’ number. (See ATEXT -356) Gaskets and Bolts are accumulated. Welds are given W or B numbers. (See ATEXT -357 & -358)

Blank or 1

STYLE 1 Material list (default)

2

STYLE 2 Material list

3

STYLE 3 Material list

Blank or 0 1

E

No action

Old Style of Material Control File (default) New Style of Material Control File.

Blank or 0

Sectionalized form of Material List with title for each group of components (default).

1

Continuous form of Material List. No headings other than those set in the Material Definition file by the user.



Word Number

E

Plotted Material List Control (continued)

Material List Type/Length Units

Switch Position

1

24

B

25

Parameter Value Options (No separate FAB / EREC sections. No component subgroup headings.) Components are continued to be sorted into Groups. Horizontal list is drawn across the Material List after each group of components. Category identifiers (ATEXT -376, -377, -378) and Group identifiers (ATEXT -307, -308, 309, -311 through -315) are both available for use in any user-specified column position. Metric or Imperial Units used with this option are goverened by ISOGEN option 41, Dimensional Units.

A

Material List Position & Title Block Position

File Marker or Data

A

B

0

Produce a material list on a per drawing basis with length units to the nearest 1/10 meter or 1/10 foot (default).

1

Produce a material list on a per pipeline basis with length units to the nearest 1/10 meter or 1/10 foot

0

Output pipe length in a x.xM or x.x’ format. (for example, 10.4M or 10.4’) (default)

1

Output pipe length in a x MM or x’ x" format. (for example, 1040 MM or 10’ 5")

2

Output pipe length in a x.xxx M or x.xxx’ format. (for example, 1.040 M or 10.510’)

0

Material List on left side of isometric drawing. The title block is located in the bottom right corner of the drawing area.

1

Material List on right side of isometric drawing. The title block is located in the bottom right corner of the drawing area.

0

Place title block in the bottom right corner of the drawing area. (default)

1

Place Title block at the bottom of the material list.



Word Number

Material List Position & Title Block Position (continued)

25

Material List Descriptions

26

Material List Text Size

Switch Position

File Marker or Data 2

Parameter Value Options Do not place a title block. Note: Check ATEXTs -317 and -318. If they are not blank and have not been positioned by the user, the Cut List SUMMARY is positioned above the title block.

27

0

Std. is = 0 to have item descriptions listed or set:

1

To suppress item descriptions.

0

For characters 2.5 mm high (default setting).

1


2

For characters 2.8 mm high. (Only controls text on isometric picture.)

3


4


5

For characters 4.9 mm high. NOTE: Setting 5 is not recommended.



Word Number

Material List Item Code Length

28

Material List Line Spacing

29

Switch Position

File Marker or Data

Controls number of characters in item code. data

The minimum item code length is 1 character.

100

Controls line spacing on material list. Std. is = 100. or set:

data

Material List Output

Picture Scale


30

Alternative value to increase/decrease in the ratio data/100/ (i.e., 105 to obtain 105/100 increase). Controls how overflow material list are split.

0

For automatic overflow onto a second material list width plotted alongside the normal one. (default)

1

Creates an isometric that contains only the material list extension.

2

Creates an overflow iso for the material list. The second iso is given the same number as the first sheet, but appends a suffix (A, B, C, etc.).

10

Same as 0 except that DRG 1 of 1 is added to single sheet isometrics.

11


12


34

100

data

Used to enlarge or diminish the isometric picture image size while keeping the frame size constant. Size alters in proportion to the number entered and 100. Std. is = 100. or set: Alternative value to increase/ decrease picture scale in the ratio to data/100.


Option Switches (continued) Isometric Facility Drawing and Material List Reserved Area

Word Number

Switch Position

File Marker or Data

35

Parameter Value Options Used to define a section along the bottom of the isometric sheet that is to be reserved for user use in both the Drawing Area and Material List Area.

A/B/C

Data

Enter a value in mms equal to the depth of reserved area that is required along the bottom of the iso above the lower frame line in the drawing area. When specified, this area always is left blank.

D/E/F

Data

Enter a value in mms equal to the depth of reserved area that is required along the bottom of the iso above the lower frame line in the Material List area. When specified, this area is always left blank. (Measured from the same place as Drawing Reserve Area) Checks to make on ATEXT -317 and -318. If they are not blank and have not been positioned by the user, the CL SUMMARY is positioned above the Material List Reserve Area.

Drawing Stacking Arrangement

36

data

37

Drawing Split Control

1

Std. is = 1 for 1 frame high stacking. Alternative value for variations on this (i.e., 2 for 2 frame high stacking, or 3 for 3 frame high stacking , etc.).

0

Std. is = 0 for plotting along the paper.

1

For plotting across the paper.

38

100 data

Controls drawing. splitting (i.e., the average amount of information to be shown on one drawing). Std. is = 100 for 100%. A number >100 to increase content or <100 to decrease.


Option Switches (continued) Isometric Facility Spool Numbers

Word Number

Switch Position

File Marker or Data

39

A

0

Spool numbering On. (use consecutive numbering - 1, 2, 3...)

1

Spool numbering Off.

2

Spool numbering On, (use consecutive lettering - A, B, C...)

0

Spool numbering is consecutive and does not reset to 1 for new sheets.

1

Spool numbering is consecutive, but resets to 1 for new sheets.

B

C

0 or blank


Spool numbers are enclosed in a double box. (default)

1

Spool numbers are enclosed in a diamond-ended box.

2

Spool numbers are enclosed in a round-ended box.

3

Spool numbers are enclosed in a triangle.

4

Spool numbers are enclosed in a diamond.

5 Spool numbers are enclosed in a square. Pipe Supports

40

Controls pipe support dispaly and dimensioning. STRING type support dimensioning. (default) A

0 OVERALL type support dimensioning 1 2

Support pipe supports on the isometric and on the material list.

3

Use undimensioned pipe supports on the isometric.



Word Number

Switch Position

File Marker or Data


Pipe Supports

40

B

0

Support dimensions are on the same side of the pipeline as normal pipe dimensions.

1

Support dimensions are opposite of the pipeline from normal pipeline dimensions. Standout distance set in positions C/D of this switch are ignored

Dimensional Units

No support dimension standout set. Program default is used.

C

0 or Blank

C/D

data

E

0 or Blank 1 2 3 4

A

0

Inch bores with metric (mm) linear dimensions.

1

Inch bores with imperial (ft/in) dimensions.

2

Metric (mm) bores with metric (mm) dimensions.

0

Metric co-ordinates are output as mm.

1

Metric co-ordinates are output as M.mm.

0

Standard output in feet and inches. (6’ 10.1/4”)

1

Same as value 0, but with an added dash. (6’10.1/4”)

2

Same as value 1, but a blank space replaces the dot. (6’-10 1/4”)

0

Do not output weight info. to the isometric (includes material lists, drawing frame, etc.). (default)

1

Output weight in kilograms.

2

Output weight in pounds.

41

B

C

D

Support dimension standout in whole mm units. Dimension all supports. Dimension Fabrication-type supports only. Dimension Erection-type supports only. Dimension Offshore-type supports only. Dimension Erection & Offshore-type supports only. Controls the output units for bore dimensions, coordinate, weight and what weight information is output , if any, for an isometric.


Option Switches (continued) Isometric Facility Dimensional Units (continued)

Word Number

Switch Position

File Marker or Data


41

E

0

Suppress weight output. Individual component weights do not appear in the materials list. Only weight sub-totals and totals appear.

1

Component Weight is output as total component weight. (quantity x unit weight).

2

Output component weight as individual weight of each component type. (not multiplied by quantity).

0 or blank

Change output format from inches to feet/inches at 24.

value

A number (in whole inches) where the output format changes from inches to feet/inches. The minimum valid value is 12.

blank

Output NPD at branches and reducers as normal.

F/G

H

View Point Control

42

1

Suppress NPD at branches and reducers.

3

N arrow points top left. (default)

1

N arrow points bottom right.

2

N arrow points top right.

4

N arrow points bottom left.

7

N arrow points top left (boxed in).

5

N arrow points bottom right (boxed in).

6

N arrow points top right (boxed in).

8

N arrow points bottom left (boxed in).



Word Number

Spare

52

Weld Numbers

53

Switch Position

File Marker or Data


A

0

Weld Numbers OFF

1

Weld Numbers ON (small characters)

2

Weld Numbers ON (medium characters)

3

Weld Numbers ON (large characters)

4

Weld Numbers ON (small characters) Only number fabrication welds

5

Weld Numbers ON (medium characters) Only number fabrication welds

6

Weld Numbers ON (large characters) Only number fabrication welds

7

Weld Numbers ON (small characters) Only number erection welds

8

Weld Numbers ON (medium characters) Only number erection welds

9

Weld Numbers ON (large characters) Only number erection welds Values 1-9 number welds consecutively, starting at 1, for the entire pipeline.

B

Blank or 0 1

C

Blank or 0

1

Do not generate a weld box. Generate a weld box. Welds numbers run consecutively, starting at 1, for the entire pipeline. Weld numbers start at 1 on each new sheet generated for a pipeline.



Word Number

Weld Numbers (continued)

Switch Position

File Marker or Data

D

0

Generate weld numbers for offshore welds

1

Generate weld numbers for offshore welds ONLY

E

Weld Control

Spare Instrument Identification

Tag Numbers

Insulation Control

54

0 or blank


Single sequence for all welds.

1

Individual sequence for each weld type

0

Std. is = 0 to have all welds plotted. or set:

1

To have all welds suppressed.

2

To have only Site welds plotted.

3

To have only Fabrication welds plotted.

4

To change Site welds to Fabrication welds. This setting will not change User Inserted Site Welds.

56-57 59

60

61

Controls which 3D system parameter is used on the isometric for the identification of instruments. 0

Std. is = 0 for instrument NAME output. or set:

1

To output the specification reference (Item Code/Tag Number) .

0

Std. is = 0 for no tag numbers on in-line items. or set:

1

To plot tag numbers

0

Std. is = 0 to have the insulation line plotted alongside the pipe. Or set:

1

To suppress insulation lines.

2

To have insulation on for tube and all insulated components

B-26 PDS ISOGEN Reference Guide - August 1999


Word Number

Tracing Control

62

Printed Material List Length Control

63

Pipe Support Information On Isometric Drawing

64

Bolting Lengths and Bolting Diameters in the Alias Material Control File Only

Switch Position

File Marker or Data


0

Std. is = 0 to have the Tracing lines plotted alongside the pipe, or set:

1

To suppress the Tracing lines.

2

To have Tracing on for tube and all traced components.

55

Std. is = 55 (for 55 lines per page), or set:

data

Alternative value (for example, 62)

0

Std. is = 0 for no Support Names on drawing [Use standard specification reference (Item Code) on parts list.],or set:

1

Support Names are output on Iso and are used in the parts list.

2

Boxed support Names are output on Iso and specification references are used on the parts list. This option allows bolt diameters and bolt lengths to be reported in different units in the printed material control file. (See ATEXT -359, -330, and -331.) Always output in Bolt Diameter X Bolt Length order.

65

0

When set to 0, bolt diameters and lengths should be treated as per the setting of option switch 41. This position controls the bolt length indicator.

A 0

Imperial diameters -- Metric Lengths

1

Imperial diameters -- Imperial Lengths

2

Metric Diameters -- Metric Lengths

3

No bolts to be included in this file.



Word Number

Switch Position

Bolting Lengths and Bolting Diameters in the Alias Material Control File Only (continued)

65

B

Coordinate Output Control

66

File Marker or Data

Parameter Value Options This position controls the bolt diameter indicator.

0 or Blank

Defaults units as set in option switch 41

1

Imperial bolt diameters

2

Metric bolt diameters

A

Control of elevations/ coordinate output on extended witness line at bend/elbow and branch intersection positions. 0

Arrowed message type

1

New style of output using extended witness line.

B

Control of coordinate output at bend/elbow positions. 0

Default setting. Only output elevations when changed.

1

No elevations/coordinates output at any bend/elbow positions

2

Only elevations/ coordinates that have changed to be output at bend/elbow positions

3

Full set of coordinates to be output at any bend/ elbow positions.

C

Control of coordinate output at branch intersection positions. 0

Default setting. Only output elevations when changed.

1

No elevations/coordinates at all branch intersection positions.

2

Only elevations/ coordinates that have changed to be output at branch intersection positions.

3

Full set of coordinates to be output at all branch intersection positions.



Word Number

Coordinate Output Control (continued)

Switch Position

File Marker or Data

D

3D Skews Drawn As 2D Skews With Fall Indication

67

Zero Length Bends

68

Control of output of coordinates at isometric split point positions. 0

No coordinate output.

1

Full set of coordinates to be output at all isometric split point positions.

0

Std. is = 0 for boxes to be put on 3D Skewed falling pipelines, or set:

1

Spare

69

Suppress Skew Boxes/Triangles on Branch Legs

70

Detail Sketch

71

Spare

72


For 3D Skews to be drawn as 2D Skews with fall indication. Where Zero Length bends are positioned between vertical branches and connection points on Falling pipelines.

0

Std. is = 0 for skewed branch connection presentation on Falling pipelines, or set:

1

For vertical branch connection presentation on Falling pipelines.

This switch is only available for use on straight through Branches. Any change in direction along the Branch automatically causes this option to default to 0. 0

Default setting. All branches are drawn with normal Skew Box/Triangle depiction.

data

Suppress Skew Box/Triangle depiction on Branch Legs whose number of components is less than or equal to the data value set. An orientation message is output as a result.

8000

This option must be set to 8000 for the Detail Sketch facility (Intergraph option 66) to operate.


Option Switches (continued) Isometric Facility Control of Part Number Box Enclosure

Word Number

Switch Position

File Marker or Data

Parameter Value Options This option offers three styles of Part Number boxes.

73

Note: When style 1 or 2 boxes are being used, ALL pipe part numbers will be converted to arrowed-out message style.

Note on Style 3: The first box identifies the weld type (Site/Shop). This is controlled from ATEXT -357, -358. The second box is the generated part number. A/B

0 data

C/D

0 data

E

0 1 2

F/G

blank data

Use standard part number enclosure. Use a Style 1 enclosure with X number of blank characters. Do not use a Style 2 enclosure. Use a Style 2 enclosure with X number of blank characters. Style 1 enclosure with square ends. Style 1 enclosure with diamond ends. Style 1 enclosure with round ends. Do not use a Style 3 enclosure box. Use a Style 3 enclosure with X number of blank characters.



Word Number

Material List Category Accumulation

74

Switch Position

File Marker or Data

Parameter Value Options Allows limited control or variations of accumulation of materials. This switch does NOT apply to a STYLE 3 Material List. In all situations, PIPE accumulates as it always has. This switch does NOT apply when using option switch 23 position B1 or B2. Accumulation ON is the default setting.

A 0

Fabrication Materials: Accumulation ON

1

Accumulation OFF (excludes pipe)

2

Eliminate the Fabrication category from the Material List.

3

Accumulation OFF (includes pipe)

0

Erection Materials: Accumulation ON

1

Accumulation OFF

2

Do not list in the Material List. The category is eliminated completely.

B

0

Offshore Materials: Accumulation ON

1

Accumulation OFF

2


C

0

Gaskets: Accumulation ON

1

Accumulation OFF

2


D



Word Number

Switch Position E

Material List Category Accumulation (continued)

F

Weld Number Box Enclosure

File Marker or Data


0

Bolts: Accumulation ON

1

Accumulation OFF

2

Do not list in the Material List. The category is eliminated completely

0

Welds: Accumulation ON

1

Accumulation OFF

2

Do not list in the Material List. The category is eliminated completely This option gives control over the style of Box enclosure for individual Weld Numbers.

75

A

For Shop Welds ONLY: Determines the enclosure style for weld numbers. All values, except for 0 weld numbers, are arrowed messages. 0

Normal weld numbers in small circles local to the weld.

1

Weld number in a diamond-ended box.

2

Weld number in a round-ended box.

3

Weld number in a triangle.

4

Weld number in a diamond.

5

Weld number in a square-ended box. Dynamically-sized circle.

6 No weld number enclosure. 7



Weld Number Box Enclosure (continued)

No. of Words and Record Format

Word Number

Switch Position

File Marker or Data

B 0

1

C


For Shop Welds ONLY: Weld prefix NOT added to the weld number. Weld prefix added to the weld number. For Site/Field Welds ONLY: Determines the enclosure style for weld numbers. All values, except for 0 weld numbers, are arrowed messages.

0

Normal weld numbers in small circles local to weld.

1

Weld number in a diamond ended box.

2

Weld number in a roundended box.

3


4


5

Weld number in a squareended box.

6

Dynamically-sized circle.

7

No weld number enclosure.

Appendix B: Alias ISOGEN Tables

B-33


Word Number

Weld Number Box Enclosure (continued)

Switch Position

File Marker or Data

D 0

For Site/Field Welds ONLY: Weld prefix NOT added to the weld number.

1

Weld prefix added to the weld number For Offshore Welds ONLY: Determines the enclosure style for weld numbers. All values, except for 0 weld numbers, will be arrowed messages.

E

F

Material Part Number Enclosure Shape

76


0

Normal weld numbers in small circles local to the weld.

1

Weld number in a diamond-ended box.

2

Weld number in a round-ended box.

3


4


5

Weld number in a square-ended box.

6

Dynamically-sized circle.

7

No weld number encosure.

0

For Offshore Welds ONLY: Weld prefix NOT added to the weld number.

1

Weld prefix added to the weld number. Note: ISOGEN option 73 controls the material part number enclosure style. Settings 1, 2, and 7 are also applied to style 2 material list part number enclosure as controlled by ISOGEN option 73.

B-34 PDS ISOGEN Reference Guide - August 1999 Isometric Facility

Word Number

Material Part Number Enclosure Shape (continued)

Weld Number Allocation at Slip-on Flanges & Reinforcement Pads Spare Valve Centerline Dimensioning Control

Switch Position

File Marker or Data


A

0

Rectangular-ended enclosure box shape (default)

1

Diamond-ended enclosure box shape

2

Round-ended enclosure box shape

7

Plot material part number only without an enclosure box.

8

Do not plot a material part number or enclosure box. This setting overrides ISOGEN option switch 73.

77

This option MUST Be Set 1 (Meaning One Weld Number Only) For Intergraph.

78 to 79 80

Dimensioning on valves with butt-welded ends.

A 0 1

Off On Dimensioning on valves with compression ends.

B 0 1

Off On Dimensioning on valves with screwed ends

C 0 1

Off On Dimensioning on valves with socket-welded ends

D 0 1

Off On Dimensioning on valves with flanged ends.

E 0 1

Off On


B-35


Word Number

Switch Position

File Marker or Data

Dimensioning on valves with flanged ends.

E

Valve Centerline Dimensioning Control (continued)

0 1

Off On Dimensioning on valves with plain ends.

F 0 1

Off On Dimensioning on valves with All Hygenic ends

G 0 1 Dimensioning Control


81

Off On Note: Branch dimensioning can not be suppressed on any branch that contains pipe, fixed length pipe or a pipe block

A/C

data

Defines upper size limit for centerline dimensioning If option switch 41 set to 0 or 1, sets the upper nominal size limit in 1/16” If option switch 41 is set to 2, sets the upper nominal size limit in whole Mms.

D/F

data

Defines upper size limit for branch dimensioning suppression. If option switch 41 set to 0 or 1, sets the upper nominal size limit in 1/16” If option switch 41 is set to 2, sets the upper nominal size limit in whole mms.

G/H

Defines the upper limit for the number of components that are required before a branch line is dimensioned.



Word Number

Switch Position

File Marker or Data

Center of Gravity Weight Output

82

A

0

None of the outputs controlled by this options switch are required. (default)

1

All selected outputs are required per drawing or per spool drawing.

2

All selected outputsare required per complete pipeline.

0

Wet wieght is not required.

1

Wet weight is required.

0

Insulation weight not required.

1

Insuulation weight required.

0

Dry (empty) center of gravity position is not required.

1

Dry (empty) center of gravity position is required.

2

Dry (empty) plus insulation center of gravity is required.

3

Dry (empty) center of gravity and dry (empty) plus insulation center of gravity are both required.

0

Wet (full) center of gravity position is not required.

1

Wet (full) center of gravity position is required.

2

Wet (full) plus insulation center of gravity is required.

3

Wet (full) center of gravity and wet (full) plus insulation center of gravity are both required.

B

C

D

E

Spare Units for Detail Sketches

Spare Plotted Leg Lengths for Elbows and Tees

83 to 91 92

93 & 94 95


Sets the type of units for detail sketches that have been used. 0 1

Metric units Imperial Units

0

Default plotted leg length of 9 mm

data

User-specified plotted leg length in whole mm units (12 = 12 mm leg lengths) Do not set below 6 mm.


B-37

Option Switches (continued) Isometric Facility Spare Skew Box/Triangle Type

Word Number

Switch Position

96 97

Spare

98

Skew Box Style And Dimensioning

99

File Marker or Data


0

Default for a Single Overall Box/Triangle enclosure around the complete skew section.

1

For individual Box/Triangle skew enclosure to each branch.

0

Std. is = 0 for Skews enclosed in full boxes with standard dimensioning. When value is set to 0, hatching is not performed.

1

For Skew Triangles with standard dimensioning.

2

For Skew Triangles with standard dimensioning but with standout distance as specified by Switch 100.

3

Skewed Box Dimension Standout (Triangles)

100

0

data

Skew Triangle Hatching

101

A

For Skew Triangles with non-standard dimensioning (i.e., no leader or dimension lines). Standout distance for positioning dimension characters as specified by Switch 100. Std. is = 0 for normal standout of 4 or 11 mm dependent on Switch 99. or set: For setting dimension standout (i.e., a setting of 120 = 12 mm or a setting of 55 = 5.5 mm). Option Switch 100 is only obeyed if Switch 99 is set to 2 or 3.

0

Hatching Off

1

Hatching On (default; 1 mm) NOTE: If set to 1, ISOGEN option 99 must not be set to 0. Reasonable value from 10 (1 mm) upwards.

A/B

data

C

0 or Blank

NO cut-off value. Full hatching is performed.

C/D

data

Hatch line cut-off length. Set in WHOLE mm.


Option Switches (continued) Isometric Facility Gapping Hatching Patterns

Word Number

Switch Position

File Marker or Data


102

A/B

0

Default gap of 25 (2.5 mm) local to skewed sections of pipeline.

data

C/D

0

data

E/F

0

Gap value set in tenths of mm (20 = 2 mm) Default gap of 25 (2.5 mm) local to pipeline items in skewed sections of pipeline Gap value set in tenths of mm (20 = 2 mm) Default gap of 15 (1.5 mm) local to text elements positioned within hatched triangles. All default settings can be selected by setting switch A to 0.

Spare Automatic Split Points in Pipe

103 to 107 108

0

No change to current operation (i.e., split points in tube are acceptable). All isometrics are generated normally. If requested, the split point information is written to new Repeatability Data Return file.

1

If split points are detected, pipeline is rejected (i.e., split points in tube are not acceptable). No isometrics are generated, and repeatability fails.

2

If split points are detected, continue to generate the required number of isometrics. The message UNACCEPTABLE SPLIT is output in the top left corner of each affected drawing. Isometrics are generated, and repeatability fails. NOTE: For Option 1 and 2, before re-running the process, you must change the pipeline data to eliminate split points. Two solutions are available: • Insert user-positioned split point(s) that avoids splitting in tube. • Insert erection-type weld at a suitable position that is local to the previously selected, reported position. As a result, a position can be dimensioned without generating a Carry Over type of dimension.


B-39


Word Number

Switch Position

Contents of Data Return File

109

A/E

Spare Dotted Nozzles

110 111

Flow Arrow Size

File Marker or Data

Determines the data output to the return file. The return file is used for repeatability. Switches must be set to 111111.

0

Std. is = 0 to have Dotted Nozzles suppressed. or set:

1

For all Nozzles to be shown Dotted. This option is used with 149 record types whose skey is set to FLOW.

112

0

Std. is = 0 set at default scale factor size of 8.

1

Supress pipeline flow arrows.

data Pipeline Reference Format In Material Control File

113

Specification Breaks

114

Offset Angle Tolerance

115

116

For scale factor size between 5 and 15.

0

Std. is = 0 for standard Pipeline Reference to output in the Material Control file. or set:

1

Reformat Pipeline Reference for output in Material Control file (change format such that 6-LNG6412A-CT15 becomes LNG6412A).

0

Std. is = 0 for standard format Specification Break identifiers. or set:

1

For new format Specification Break identifiers.

0

Std. is = 0 for no offset tolerance. or set:

data

Offset Dimension Tolerance


0

data

Any angle value expressed in 1/100ths of a degree. Thus, any skew below the angle value input is suppressed. Std. is = 0 for no offset tolerance. or set: Any value expressed in 1/100ths of a millimeter. Thus, any skew below the given value is suppressed.


Option Switches (continued) Isometric Facility Dimension Round Off Carry Over

Overall Dimensions

Vertical Dimensions/ Elevations

Scale of Tapped Branch

Tapped Branch Dimensions

Word Number

Switch Position

File Marker or Data


0

Std. is = 0 for the carry over of any remaining dimension after rounding up or down to the nearest whole unit (i.e., nearest 1 mm or 1/16 inch). or set:

1 0

For no carry over after rounding up or down to the nearest 1 mm or 1/16 inch. Overall dimensions OFF

1

Overall dimensions ON, going across all branches

2

Overall dimensions ON, stopping at all branches

3

Overall dimensions to center line of valves, going across all Branches

4

Overall dimensions to center line of valves stopping at all branches.

B

0 or Blank

NO overall dimension standout set. Program default will be used for all overall dimensions.

B/C

data

User-specified overall dimension standout in whole mm units (9 for 9 mms)

117

118

119

120

121

A

0

Std. is = 0 for normal dimensions. or set:

1

Elevations only output on vertical pipes at points where dimension lines would normally be.

2

Elevations and Dimensions output on vertical pipelines.

0

Std. is = 0 for 100% pipeline scale. or set:

data

Value >100 to increase the branch scale. Value <100 to decrease the branch scale. Values of less than 50% are not recommended.

0

Std. is = 0 for dimensions on as set for the main pipeline. or set:

1

For dimensions off.


B-41


Word Number

Coordinates at Tapping Points

122

Instrument Balloons

Switch Position

123

B

File Marker or Data


0

Std. is = 0 for no coordinates output at user-defined fitting tap points. or set:

1

For coordinates output at developed fitting tap points.

0

Std. is = 0 for no ballooning of instrument text. or set: A number equal to the number of characters allow on each of the two available lines within an instrument balloon; i.e.:

1

For 1 character on each line.

2

For 2 characters on each line.

3


4


5


0

This switch position is not used. Set this switch position to 0 as a place holder when using switch position C. NOTE: When using any of the enclosure options for switch C, switch A must be set to 0. NOTE: Refer to Intergraph Option 12 if a two line message is required or if the instrument ID is defined using a $ character. Otherwise, a line feed will occur at the $ character.


Option Switches (continued) Isometric Facility Instrument Balloons (continued)

Word Number

Switch Position

File Marker or Data

123

C

0 or blank

Spare

124 to 126

Test Parameter Block

127 to 140

Parameter Value Options No enclosure box around the instrument name (default setting).

1

Diamond-ended box

2

Round-ended box

3

Diamond-ended box (2 character maximum)

4

Diamond-shaped box (3 character maximum)

5

Square-ended box

Used for Isodat/Isoplot development testing by Alias ISOGEN Support Team.


Symbol Keys General Information: End Prep Connections: The ** characters in the symbol key may be replaced with one of the following end prep types:

End Type

End Prep Codelist Value Range

End Prep Type (**)

Flanged

2 - 199

FL (Flanged)

Male

321 - 329 331 - 339 341 - 349 351 - 359 361 - 369 371 - 379 381 - 389 401 - 409

LC (Liner - clamped) SC (Screwed) LC (Liner - clamped) LC (Liner - clamped) CP (Compression) SC (Screwed) SC (Screwed) CP (Compression)

Female

420 - 429 440 - 449 501 - 509

SW (Socket Weld) SC (Screwed) CP (Compression)

All Other Codelist Values

BW (Butt Weld)

Number of Segments: The @ character in the symbol key may be replaced with an integer value in the range 1 to 9, inclusive, to denote the number of segments. Currently, regardless of the value assigned to @, the symbol is drawn per the Skey Plotted Isometric Shape displayed in this section. However, in a future release of the software, the numeric value assigned to @ will be used in conjunction with a costing package so that the number of segments in the bend can be passed to the costing system.

Bend Radius: The + character in the symbol key may be replaced with an integer value in the range 1 to 9, inclusive, to denote the bend radius.

Skey Connect Points: Please refer to Appendix E, ISOGEN Skey Dimensions, for the position of Skey connection points.


Symbol Keys for Flanges Description

Key

Plotted Isometric Shape

User-Definable (Yes/No)

Flange - Blind (Blank)

FLBL

Y

Flange - Flared/Loose Backing

FLFL

Y

Flange - Loose Backing

FLLB

Y

Flange - Reducing Concentric

FLRC

Y

Flange - Reducing Eccentric

FLRE

Y

Flange - Slip On

FLSO

Y

Flange - Slip On With ’J’ Type Weld

FLSJ

Y

Flange - Orifice Slip On

FOSO

Y

Flange - Socket Weld

FLSW

Y

Flange - Weld Neck

FLWN

Y

Flange - Orifice Weld Neck

FOWN

Y

Symbol Keys for LJSE Type Flanges Description

Key



Lap Joint Ring (Loose Backing Flange)

FLRG

Y

Lap Joint Stub End (Loose Backing Flange)

FLSE

Y


Symbol Keys for Miscellaneous Pipe Components Description

Key



Block - Angle

BA**

N

Expansion Bellows

EX**

Y

Flame Trap

FT**

Y

Flexible Hose

FX**

Y

Hose Coupling

CH**

Y

Non-Category Item

NC**

Y

Block Offset

BO**

N

Plug

PL

Y

Restrictor Plate

RP

Y

Block - Return

BR**

N

Sight Glass

SG**

Y

Slip Plate

SP

Y

Slip Ring

SR

Y


Symbol Keys for Miscellaneous Pipe Components (continued) Description Spectacle Blind

Tundish (Funnel)

Key



SB

Y

TU**

Y

Symbol Keys for Miscellaneous Items Description

Key



Flow Indicator

FLOW

Y

Hanger/Support

01HG

Y

Symbol Keys for Instruments Description

Key



Instrument

II**

Y

Instrument - Angle

IA**

N

Instrument - Offset

IO**

N

Instrument - Return

IR**

N

Instrument - Dial

IDPL

N


Symbol Keys for Instruments (continued) Description Instrument - Dial Flanged

Key



IDFL

N

Orifice Plate

OP

Y

Restrictor Plate

PR

Y

Symbol Keys for In-Line Filters Description

Key



Filter/Strainer Straight Through

FI**

Y

Filter/Strainer Angle

FA**

N

Filter/Strainer Offset

FO**

N

Filter/Strainer Return

FR**

N

Symbol Keys for Instruments Description

Key



Rupture Disk

DR

Y

Valve - Angle Relief/Vent

RA**

Y

Valve - Angle Pressure Reducing

XA**

Y


Symbol Keys for Instruments (continued) Description

Key



Valve - Control

CV**

Y

Valve - Angle Control

CA**

Y

Valve - 3-Way Control

C3**

N

Valve - 4-Way Control

C4**

N

Valve - Control Square Indicator

SV**

Y

Valve - Angle Control Square Indicator

SA**

Y

Valve - 3-Way Control Square Indicator

S3**

N

Valve - 4-Way Control Square Indicator

S4**

N

Valve - Control Motorized Indicator

MV**

Y

Valve - Angle Control Motorized Indicator

MA**

Y

Valve - 3-Way Control Motorized Indicator

M3**

N

Valve - 4-Way Control Motorized Indicator

M4**

N

Valve - Control Hand Indicator

HV**

Y


Symbol Keys for Instruments (continued) Description

Key



Valve - Angle Control Hand Indicator

HA**

Y

Valve - 3-Way Control Hand Indicator

H3**

N

Valve - 4-Way Hand Indicator

H4**

N

Valve - Pressure Reducing

XV**

Y

Valve - Relief/Vent

RV**

Y

Symbol Keys for Vent Description Rupture Disk

Key


RD

User-Definable (Yes/No) Y

Symbol Keys for Traps Description

Key



Trap - In-Line (Straight Through)

TI**

Y

Trap - Angle

TA**

N

Trap - Offset

TO**

N

Trap - Return

TR**

N


Symbol Keys for Welds Description

Key



Weld - Site

WS

Y

Weld - Field Fitted

WF

Y

Weld - Workshop

WW

Y

Weld Mitre (Shop) 14=1

WM

N

Weld Mitre (Site) 14=2

WM

N

Weld Mitre (Offshore) 14=3 Weld Mitre (Field Fit) 14=2 Weld Mitre (Field Fit) 14=3 Offshore Weld

WM

N

WMF

N

WMF

N

WO

Y

WOF

Y

Offshore Weld-Field Fit

Symbol Keys for Other End Connections Description Erection Weld / Connection on fittings with an SW end Erection Weld / Connection on fittings with an SC end Erection Weld / Connection on fittings with a CP end

Key



SW

Y

SC

Y

CP

Y

NOTE: For SW, SC, or CP type end connections, the plotted shape is filled in for erection and left open for fabrication type items. If the connecting pipe fabrication category is erection, then it will override whatever is defined in the fitting.


Symbol Keys for Elbows and Bends Description

Key



Elbow - Butt Weld (90° and 45°)

ELBW

N

Elbow - Butt Weld (90° and 45°) With A Connection

ETBW

N

Elbow - Butt Weld 180° Return (U Elbow)

EUBW

N

Elbow - Compression (90° and 45°)

ELCP

N

Elbow - Compression (90° and 45°) With A Connection

ETCP

N

Elbow - Screwed (90° and 45°) With Male Ends

EBSC

N

Elbow - Screwed (90° and 45°) With Female Ends

ELSC

N

Elbow - Screwed - Female (90° and 45°) With A Connection

ETSC

N

Elbow - Socket Weld

ELSW

N

Elbow - Socket Weld With A Connection

ETSW

N

Bend - Flanged (All Angles)

BEFL

N

Bend - Flanged (All Angles) With A Connection

BTFL

N

Bend - Flanged 180 Return (U Bend)

BUFL

N

Bend - Miter Flanged

MIFL

N


Symbol Keys for Elbows and Bends (continued) Description

Key



Bend - Miter Flanged With A Connection

MTFL

N

Bend - Miter Butt Weld

MIBW

N

Bend - Miter Butt Weld With A Connection

MTBW

Y

Bend - Lobster Back Flanged

L@FL

N

Bend - Lobster Back Flanged With A Connection

T@FL

N

Bend - Lobster Back Butt Weld

L@BW

N

Bend - Lobster Back Butt Weld With A Connection

T@BW

N

Bend - Pulled (All Angles)

PB+D

N

Bend - Pulled 180 Return (U Bend)

BU+D

N

Bend - Pulled (All Angles) With A Connection

TB+D

N


Symbol Keys for Couplings Description

Key



Nipple - Screwed (Running)

NRSC

Y

Nipple - Screwed (Barrel)

NBSC

Y

Coupling - Compression

COCP

Y

Coupling - Screwed

COSC

Y

Coupling - Socket Weld

COSW

Y

Elbolet Coupling Butt Weld

CEBW

Y

Elbolet Coupling Screwed

CESC

Y

Elbolet Coupling Socket Weld

CESW

Y

Symbol Keys for Caps Description

Key



Cap - Butt Weld

KABW

Y

Cap - Compression

KACP

Y

Cap - Screwed

KASC

Y

Cap - Socket Weld

KASW

Y


Symbol Keys for Crosses Description

Key



Cross - Butt Weld

CRBW

N

Cross - Compression

CRCP

N

Cross - Flanged

CRFL

N

Cross - Screwed

CRSC

N

Cross - Set On

CRSO

N

Cross - Set On Reinforced

CRRF

N

Cross - Socket Weld

CRSW

N

Symbol Keys for Fixed Length Pipes Description

Key



Fixed Length Pipe With Flanged Ends

FPFL

N

Fixed Length Pipe Without Flanged Ends

FPPL

Y


Symbol Keys for O’lets Description

Key



O’let - Half Coupling Screwed

HCSC

Y

O’let - Half Coupling Socket Weld

HCSW

Y

O’let - Latrolet Butt Weld

LABW

Y

O’let - Latrolet Screwed

LASC

Y

O’let - Latrolet Socket Weld

LASW

Y

O’let - Nipolet Screwed

NISC

Y

O’let - Nipolet Plain End

NIPL

Y

O’let - Sockolet

SKSW

Y

O’let - Sweepolet

SWBW

Y

O’let - Thredolet

THSC

Y

O’let - Weldolet

WTBW

Y

Instrument Tee Flanged

ITFL

N


Symbol Keys for Tees Description

Key



Tee - Butt Weld

TEBW

N

Tee - Compression

TECP

N

Tee - Flanged

TEFL

N

Tee - Screwed

TEFL

N

Tee - Set On

TESO

N

Tee - Set On Reinforced

TERF

N

Tee - Socket Weld

TESW

N

Tee - Swept Branch Butt Weld

TSBW

N

Tee - Swept Branch Flanged

TSFL

N

Tee - Swept Branch Compression

TSCP

N

Tee - Swept Branch Socket Weld

TSSW

N


Symbol Keys for Reducers Description

Key



Reducer - Concentric Butt Weld

RCBW

Y

Reducer - Concentric Fabricated From Plate

CPBW

Y

Reducer - Concentric Swaged From Pipe

CSBW

Y

Reducer - Concentric Butt Weld With A Connection

CTBW

Y

Reducer - Concentric Fabricated From Plate With A Connection

CZBW

Y

Reducer - Concentric Swaged From Pipe With A Connection

CXBW

Y

Reducer - Concentric Compression

RCCP

Y

Reducer - Concentric Flanged

RCFL

Y

Reducer - concentric Fabricated From Plate Flanged

CPFL

Y

Reducer - Concentric Swaged From Pipe Flanged

CSFL

Y

Reducer - Concentric Fabricated From Plate Flanged w/ Connection

CZFL

Y

Reducer - Concentric Swaged From Pipe Flanged w/ Connection Reducer - Concentric Nipple

CXFL

Y

RNSC

Y

RCSC

Y

Reducer - Concentric Screwed


Symbol Keys for Reducers (continued) Description

Key



Reducer - Concentric Screwed w/ Connection

CTSC

Y

Reducer - Concentric Screwed Bush

RBSC

Y

Reducer - Concentric Socket Weld Bush

RBSW

Y

Reducer - Eccentric Butt Weld

REBW

Y

Reducer - Eccentric Fabricated From Plate

EPBW

Y

Reducer - Eccentric Swaged From Pipe

ESBW

Y

Reducer - Eccentric Butt Weld With A Connection Reducer - Eccentric Fabricated From Plate With A Connection

OTBW

Y

EZBW

Y

Reducer - Eccentric Swaged From Pipe With A Connection Reducer - Eccentric Screwed

EXBW

Y

RESC

Y

Reducer - Eccentric Screwed With A Connection Reducer - Eccentric Flanged

OTSC

Y

REFL

Y

Reducer - Eccentric Fabricated From Pipe Flanged

EPFL

Y

Reducer - Eccentric Swaged From Pipe Flanged

ESFL

Y


Symbol Keys for Reducers (continued) Description Reducer - Eccentric Flanged With A Connection Reducer - Eccentric Fabricated From Plate Flanged With A Connection Reducer - Eccentric Swaged From Pipe Flanged With A Connection Reducing Block

Key



OTFL

Y

EZFL

Y

EXFL

Y

RFPL

Y

Symbol Keys for Unions Description

Key



Union - Screwed

UNSC

Y

Union - Socket Weld

UNSW

Y

Symbol Keys for Valves Description

Key



Valve - Angle

AV**

Y

Valve - Angle Pressure Reducing

AX**

Y


Symbol Keys for Valves (continued) Description

Key



Valve - Angle Relief/Vent

AR**

Y

Valve - Ball

VB**

Y

Valve -Basic

VV**

Y

Valve - Butterfly

VY**

Y

Valve - Check

VC**

Y

Valve - Check

CK**

Y

Valve - Cock

VK**

Y

Valve - Diaphragm

VD**

Y

Valve - Gate

VT**

Y

Valve - Globe

VG**

Y

Valve - Needle

VN**

Y

Valve - Plug

VP**

Y

Valve Pressure Reducing

VX**

Y


Symbol Keys for Valves (continued) Description

Key



Valve - Relief/Vent

VR**

Y

Valve - Slide

VS**

Y

Symbol Keys for Three-Way Valves Description Valve - 3-Way

Key



V3**

N

Symbol Keys for Four-Way Valves Description Valve - 4-Way

Key V4**


User-Definable (Yes/No) N


Symbol Keys for Operators Description

Key



Fitting used on valves with AV, V3, V4, VD, VG, VV, as first two characters of the SKey Fitting used on valves with AR, RA, VR as 1st 2 chars of the SKey

01SP

Y

02SP

Y

Fitting used on valves with VB, VK, VY as first two characters of the SKey

03SP

Y

Fitting used on valves with VT as first two characters of the SKey

05SP

Y

Fittings used on valves with VT as first two characters of the SKey

06SP

Y

Fittings used on valves with VP as first two characters of the SKey

07SP

Y

Fittings used on valves with VS as first two characters of the SKey

08SP

Y

Fittings used on control valves with AX, VX and XA as first two characters of the SKey

09SP

Y

Fittings used on control valves with SA, SV, S3 and S4 as first two characters of the SKey

10SP

Y

11SP

Y

Fittings used on control valves with MA, MV, M3 and M4 as first two characters of the SKey


Symbol Keys for Operators (continued) Description

Key



Fittings used on control valves with HA, HV, H3, and H4 as first two characters of the SKey

12SP

Y

Fittings used on control valves with CA, CV, C3 and C4 as first two characters of the SKey

13SP

Y


Alternative Texts Available (The AText Facility) All text on the isometric drawing can be changed or removed. This Appendix lists the default values of the text with their reference numbers. These alternative texts have been broken down under the following headings: •

Numerical Listing of Alternative Texts (AText)

•

The Isometric Drawing Area

•

The Title Block Area

•

The Plotted Material List

•

The Line Summary Area

•

The Printed Material List

•

The Weld Box Summary

If an AText Number is set to blank, both the default text and any associated attribute that has been extracted from the database is suppressed on the drawing.

Appendix B: AText Facility - by Number

B-65

Numerical Listing of Alternative Texts (AText) -208 CONN. TO

denotes CONNected TO where a pipe end is connected to a Nozzle.

-209 CONT. ON

denotes CONTinued ON where a pipe end is continued on another Pipeline or the drawing when a pipeline is split onto two or more drawings (in conjunction AText -255).

-201 E

denotes East at coordinates.

-202 N

denotes North at coordinates.

-203 W

denotes West at coordinates.

-204 S

denotes South at coordinates.

-205 EL +

denotes a positive Elevation at coordinates.

-206 EL -

denotes a negative Elevation at coordinates.

-207 NS

denotes the pipe Nominal Size.

-210 F

denotes Flange. The letter is used in the material list pointer for flanges.

-211 G

denotes Gaskets. The letter is used in the material list pointer for gaskets.

-212 B

denotes Bolts. The letter is used in the material list pointer for bolts

-213 SPINDLE

is used to give a spindle direction of a valve when it is not in a primary direction.

-214 MM

denotes Millimeters, used for arrowed dimensions on Angle and Multiway Valves.

-215 REDUCING FLANGE

Message is pointed at each Reducing Flange.

-216 OFFSET

This message is used where an offset occurs. Examples of locations are Eccentric Reducers, Offset Reducing Flanges, and Offset Blocks

-217 MITER

This message is used where a Mitered Bend occurs.

-218 LOBSTER

This message is used where a Lobster Back Bend occurs.

-219 REINFORCED

Message is pointed at each reinforced Tee or Cross where the symbol key is TERF or CREF.

-220 LEFT LOOSE

Message is pointed at any Flange where LOOSE indicator is set.

-221 FFW

Message is pointed at any Field Fit Weld (i.e., Welds with key WF).

-222 FALL

denotes FALLing line.

-223

When left blank, this AText automatically produces the degree symbol for falling lines specified with angle Fall indication.

B-66 PDS ISOGEN Reference Guide - August 1999 -224

This symbol is used for Falling lines specified with a ratio, such as 1:10.

-225

When left blank, this AText automatically produces the % symbol for Falling lines specified with a percentage.

-226 GRAD

is shown where a Falling line is specified in GRADS.

-227 PER M

is used where a falling line is specified as an incline in Metric units, (such as Millimeters per Meter).

-228 PER FT

is used where a falling line is specified as an incline in Imperial units, (such as, Inches per Foot).

-229 SCREWED END

Message is pointed at any pipe (tube) end that has been set to screwed in the intermediate file.

-241 (default blank)

This AText is blank by default and can be used to produce a message at any open end item that is identified by a -32 record.


This AText is blank by default and can be used to produce a message at any open end item that is identified by a -36 record.


This AText is blank by default, but if set to any word, such as FLAT, then eccentric reducers in orthogonal piping have an indication of the orientation of their flat side. Note: By setting the -243 AText, the Attests -244, -245, -246, -247, -248, and -249 are also used.

-244 UP

used with AText -243.

-245 DOWN


-246 NORTH


-247 SOUTH


-248 EAST


-249 WEST


-250 DATE

This is used in the title block and the actual date is automatically appended in the required format (whether UK, EUR or USA). This AText also uses the Attests 258, -259, -269, -261, -262, -263, -264, -265, -266, -267, -268, -269 if the date format is set to UK.

-251 PROJECT NO.

This is used in the title block if the Project Number has been set in a -9 record.

-252 BATCH REF

This is used in the title block area if some form of reference has been set in a 10 record.

-253 PIPING SPEC

This is used in the title block area and the content of a -11 record is appended.


B-67

-254 ISS


-255 DRG

This is only used when a pipeline is split to more than one sheet. Used with AText -256 to indicate DRG n OF n (for example, drawing 1 of 1). Also used by AText -276.

-256 OF


-257 SPL

denotes a SPOOL drawing. A sequential number starting at one end of each pipe is automatically appended.

-258 JAN


-259 FEB


-260 MARCH


-261 APR


-262 MAY


-263 JUN


-264 JUL


-265 AUG


-266 SEP


-267 OCT


-268 NOV


-269 DEC


-270 THERMAL INSULATION SPEC

is used in the title block and the content of a -15 record is automatically appended.

-271 TRACING SPEC


-272 PAINTING SPEC


-275 SWEPT TEE

Message is plotted and pointed to any tee whose symbol key starts with TS.

-276 CONT. FROM

denotes CONTinued FROM. This message is plotted wherever a pipeline is split onto two or more drawings (for example, CONT. FROM DRG 1). Note: The -276 AText also uses AText -255 for the DRG text.

-277 ORIFICE FLANGE

Message is plotted and pointed to Orifice Flanges.

-278 DIAL FACE

Message is plotted next to Instruments Dials (symbol keys IDPL and IDFL) followed by relevant direction. See note below.

-280 TAPPING

Message is plotted at Orifice Plates followed by relevant direction.

B-68 PDS ISOGEN Reference Guide - August 1999 -281 TAIL -282 WINDOW

Message is plotted at Spectacle Blinds and Slip Plates followed by relevant direction. Message is plotted at Site Glass followed by relevant direction. Note: AText Numbers -278, -280, -281 and -282 are only output if a primary direction is set in Word 14 of the component record. The appropriate direction, as defined by ATexts -244 to -249, is appended to the specific fitting text (such as DIAL FACE WEST).

-283 FLAT

This AText is used to indicate the orientation of the flat side of an eccentric reducer, when the reducer is in a skew. The contents of this AText is output in front of the contents of the -40 record containing the Flat direction. Note: The following six ATexts are used to output directions (with other ATexts) on items that carry a direction setting in Word 14 of the component record in the intermediate file.

-284 TEE BEND

used to denote a Tee Bend.

-285 RATING FLANGE

Message is a facility to provide an extra message at a Flange to show different rating. This is done by giving the mating Gasket a symbol key of the required rating, such as 300#. Only used for fixed-length piping.


This AText is blank by default, but, if set, outputs a message on screwed erection fittings.

-287

Message on offset o’lets, followed by the direction of the off-line leg.

ORIENTATION DIRECTION

-288 PIPE

used on System Isometrics to denote position(s) of change in Pipeline Reference.

-289 MATL

used to indicate PIPING MATERIAL Spec. change. Content of -26 record appended.

-290 INSUL

used to indicate INSULATION Spec. change. Content of -15 record appended.

-291 TRACE

used to indicate TRACING Spec. change. Content of -16 record appended.

-292 PAINT

used to indicate PAINTING Spec. change. Content of -17 record appended.


To be user-defined. Contents of -41 record appended. The contents of a MISC-SPEC1 type record in the Pipeline Input Data File is appended to the AText to form a composite message.






B-69





-298 TEE ELBOW

used to denote a Tee Elbow.

-300 FABRICATION MATERIALS

is the heading under which components required for ’SHOP’ fabrication are listed. Word 14 of component record set to 1.

-301 PT

is the part number pointer used with AText -302.

-302 NO


-303 COMPONENT

is the heading in the material listing under which components are described according to their catalogue component description.

-304 N.S.

denotes Nominal Size

-305 ITEM CODE

is the heading under which component identification codes are listed.

-306 QTY

denotes Quantity required.

-307 PIPE

is the subheading under which Pipe is listed. This AText should be used whenever the ’GROUP’ facility is used as a data item on STYLE 2 or STYLE 3 material lists. This AText allows you to set an abbreviation -text that is used in the designated column for each component listed.

-308 FITTINGS

is the subheading under which Pipe Fittings, such as elbows, tees, etc., are listed. This AText should be used whenever the ’GROUP’ facility is used as a data item on STYLE 2 or STYLE 3 material lists. This AText allows you to set an abbreviation text that is used in the designated column for each component listed.

-309 FLANGES

is the subheading under which all Flanges are listed. This AText should be used whenever the ’GROUP’ facility is used as a data item on STYLE 2 or STYLE 3 material lists. This AText allows you to set an abbreviation text that is used in the designated column for each component listed.

-310 ERECTION of MATERIALS

is the heading under which components required for ’SITE’ erection are listed. Word 14 component record set to 2.

-311 GASKETS

is the subheading under which all Gaskets are listed. This AText should be used whenever the ’GROUP’ facility is used as a data item on STYLE 2 or STYLE 3 material lists. This AText allows you to set an abbreviation text that is used in the designated column for each component listed.

-312 BOLTS

is the subheading under which all Bolts are listed. This AText should be used whenever the ’GROUP’ facility is used as a data item on STYLE 2 or STYLE 3 material lists. This AText allows you to set an abbreviation text that is used in the designated column for each component listed.


-313 VALVES / IN-LINE ITEMS

is the subheading under which all Valves and In-line Items are listed. This should be used whenever the ’GROUP’ facility is used as an data item on STYLE 2 or STYLE 3 material lists. This AText allows you to set an abbreviation text that is used in the designated column for each component listed.

-314 INSTRUMENTS

is the subheading under which all Instruments are listed. This AText should be used whenever the ’GROUP’ facility is used as a data item on STYLE 2 or STYLE 3 material lists. This AText allows you to set an abbreviation text that is used in the designated column for each component listed.

-315 SUPPORTS

is the subheading under which all Supports are listed. This AText should be used whenever the ’GROUP’ facility is used as a data item on STYLE 2 or STYLE 3 material lists. This AText allows you to set an abbreviation text that is used in the designated column for each component listed.

-316 PIPE SPOOLS

is the subheading under which all Spool Numbers are listed.

-317 PIPE NS

is used with AText -318 to which the total Center Line Length per bore is automatically computed and listed.

-318 CL LENGTH

is used with AText -317.

-319 CUT PIPE LENGTHS

is the heading under which all the Cut Pipe Lengths are listed.

-320 PIECE

is the subheading to AText -319 under which the Cut Pipe piece numbers are listed. This AText is used with AText -321.

-321 NO


-322 CUT

is the subheading to AText -319 under which the actual Cut Pipe Lengths are lis This AText is used with AText -323.

-323 LENGTH

is the subheading to AText -319 under which the actual Cut Pipe piece numbers are listed. AText -361 is positioned below LENGTH when Imperial Units are used. AText-331 is positioned below LENGTH when Mixed or Metric Units are used. To be moved up to the top line of the cut list heading.

-323 LENGTH


-324 REMARKS

is the subheading to AText -319 under which one of the ATexts -326, -327, or -32 if applicable, is listed.

-326 PLD BEND

denotes Pulled BEND remark that is listed under AText -324 if a Cut Pipe Length contains a pulled bend.

-327 LOOSE FLG

is a remark that is listed under AText -324 if a Cut Pipe Length has a loose flang attached.

-328 FF WELD

denotes the Fitted Field Weld remark that is listed under AText -324 if a Cut Pipe Length contains a Fitted Field Weld.

-329 M

denotes lengths of Pipe are in METERS.

-330 INS

denotes Nominal Sizes are in INCHES.

-331 MM

denotes the Nominal Sizes are in MILLIMETERS.


B-71

-332 PAGE

has a Page Number automatically appended.

-333 PIPELINE REF

has the Pipeline Reference automatically appended.

-334 S

is used with Fixed Length Piping and the contents of this AText (default S) is appended to the Item code when one end of the Fixed Length spool has a special flange.

-335 WITH SPECIAL RATING

is used with Fixed Length Piping and the contents of the AText are appended to the FLANGE(S) (SEE ISO)description. Used with AText -334.

-336 SYSTEM REF

is used as an alternative to AText -333 when producing Material List for System Isometric. Content of a -25 record is automatically appended.

-338 BEND RADIUS

used to denote a bend radius for a pipe bend.

-339 MISCELLANEOUS COMPONENTS

is the subheading under which miscellaneous components are listed. This AText should be used whenever the ’CATEGORY’ facility is used as a data item on STYLE 2 or STYLE 3 Material Lists. This AText allows you to set an abbreviation text that is used in the miscellaneous column for each component listed.

-340 INDUCTION BEND ID

used to identify pipe required in the fabrication of induction bends. The induction bend tag is appended to the AText to form a complete string.


This AText is available as an alternative to the AText used when generating a Material List over flow at the bottom of the master drawing Material List (combination of ATexts -206 and -255). Any AText set by the user will have a program generated cross reference drawing number appended to it.


This AText is available as an alternative to the AText used when generating a Material List over flow at the top of the overflow Material List drawings (combination of ATexts -276 and -255). Any AText set by the user will have a program generated cross reference drawing number appended to it.

-349 PP

Is used to indicate Personal Protection type insulation on Insulation Indication symbols having the symbol key 'INPP’.

-350 REDUCING ELBOW

Is used to indicate a REDUCING ELBOW on fittings having the symbol key ER**.

-351 DRG$

generates DRG nl 1 of 2. This is done by replacing DRG$ with SHT$. With this configuration, SHT (or sheet) nl 1 of 2 is available.

-352 WEIGHT

column heading on Material List.

-353 KGS

unit indication at all positions where weight is output (used with ISOGEN switch 41 position D).

-354 LBS

unit indication at all positions where weight is output (used with ISOGEN switch 41 position D).

-355 TOTAL

weight subtotal identifiers. This AText must be set to BLANK if this type of output PIPELINE is not required.


-356 U

used to identify all Pulled Bends. Used on the ISO and the material list as ’U3’.

-357 B

used to identify all ERECTION type Welds (on ISO and Material List) when positions F/G for option 73 are defined.

-358 W

used to identify all FABRICATION type Welds (on ISO and Material List) when positions F/G for option 73 are defined.


Bolt size x Length headings. Used with option switch 65 (Material Control File Only). A suggested setting is "DIA x LENGTH". If this AText is not blank, ISOGEN outputs in Bolt Diameter x Bolt Length order. Bolt Units are indicated immediately below this heading using a program-generated text string using a combination of ATexts -330 (INS) and -331 (MM), depending on the settings for option switch 65. For example: DIA x LENGTH (INS x INS)

-360 FT

used with the old style Material List in conjunction with AText -318 (See ISOGEN option 24).

-361 FT-INS

used with the new style Material List in conjunction with AText -318 (See ISOGEN option 24).

-362 END$ONE

is the subheading to AText -319. Describes the operations necessary to prepare the end for fabrication. End connections are listed for pipe. (See ISOGEN option 2 setting 11 or 12.) (See AText -366 through -370.)

-363 END$TWO

is the subheading to AText -319. Describes the operations necessary to prepare the end for fabrication. (See ISOGEN option 2 setting 11 or 12.) (See AText -366 through -370.)


is the alternative last column subheading to AText -319 under which cut pipe item code are listed for pipe. When used for Part Number, a suggested setting is:"PART$NO"(See ISOGEN option 2 setting 11 or 12). If Part No. is required on the Cut List instead of ITEM CODE, then AText -364 should be set to ’blank’ and AText -365 set to required heading (for example, PART$NO.)

-366

SQ.CUT

-367

BEVEL

used for Square Cut in End Condition columns on the Cut Pipe List. (See ISOGEN option 2 setting 11 or 12). used for all Butt Welds (BW) Items that are treated as BW’s, but do not have the BW end condition as part of their SKEY. (See ISOGEN option 2 setting 11 or 12) Flanges: FLWN - Flange Weld Neck FOWN - Flange Orifice Weld Neck FLSE - LJSE Butt Weld Type All other flange type items use Square Cut (AText -366)

-368

SCREWED

used for all Screwed Ends (SC). (See ISOGEN option 2 setting 11 or 12.)

-369

SHAPED

used for all Fabricated Branch connections. (See ISOGEN option 2 setting 11 or 12.)

-370

MITRED

used for all mitred ends at mitre weld positions. (See ISOGEN option 2


B-73

setting 11 or 12.) -371

OFFSHORE MATERIALS

Material List main heading for offshore items. All materials sorted within this new category as for other two categories (where appropriate).

-372

REMARKS

heading for Remarks box.

-373

REM

column heading for Remarks column on material list.

-374

ANGLE

used with description of Pulled Bends in the material list. Bend angle is output when using ISOGEN option 23 set to 20 or 21.

-375 WELDS

is the subheading under which welds are listed. This AText should be used whenever the ’CATEGORY’ facility is used as a data item on STYLE 2 or STYLE 3 Material Lists. This AText allows you to set an abbreviation text that is used in the weld column for each component listed.

-376 FAB

identification of FABRICATION material. To be used whenever the ’CATEGORY’ facility is used as a data item on STYLE 2 or STYLE 3 Material Lists. This AText allows the user to set an abbreviation text that is used in the fabrication column for each component listed.

-377 EREC

identification of ERECTION material. To be used whenever the ’CATEGORY’ facility is used as a data item on STYLE 2 or STYLE 3 Material Lists. This AText allows the user to set an abbreviation text that is used in the erection column for each component listed.

-378 OFF

identification of OFFSHORE material. To be used whenever the ’CATEGORY’ facility is used as a data item on STYLE 2 or STYLE 3 Material Lists. This AText allows the user to set an abbreviation text that is used in the offshore column for each component listed.

-379

TOTAL FABRICATION WEIGHT

weight subtotal identifiers. This AText must be set to BLANK if this type of output is not required.

-380

TOTAL ERECTION WEIGHT


-381 TOTAL OFFSHORE WEIGHT


-400 TRACED$PIPE -401 LAGGED$PIPE -402 PIPE$SUPPORT -403 COMPN$JOINT -404 SCREWED$JOINT -405 SOCKET$WELD -406 FIELD$WELD -407 SHOP$WELD

B-74 PDS ISOGEN Reference Guide - August 1999 -410 [1] DENOTES PIPE SPOOL NO$ -1 DENOTES PARTS LIST NO

If only the bottom line is required, the records in the intermediate file should be: -410 $ 1 DENOTES -1 PARTS LIST NO

-411 SITE$CONNECTION -412

WELD|SHOP|WELD |WELDER|VISUAL |NOT|HARD|S.R|FAB.QA

weld header box details (line 1).

-413 NO |/FLD|PROC| ID |ACCEPT| NO| NO | |ACCEPT

continuation of weld box header details. (line 2)

-414 S

Fabrication/Shop Weld. Used in the Weld Category identification on the Old Style Weld Box. When using all three weld types, AText -412 and -413 column 2 is probably changed to give a heading that covered all types. For example: WELD CAT

-415 F

Erection/Field/Site Weld. Used in the Weld Category identification on the Old Style Weld Box.

-416 O

Offshore Weld. Used in the Weld Category identification on the Old Style Weld Box.

-417 - -423

used for Weld Type in the Weld Box and/or Weld Summary Report.

-417 BW

for All Butt Welds. All fittings with BW end type in addition to: FLWN and FOWN flanges FLSE and LJSE type flanges.

-418 SW

for all Socket Welds. All fittings with SW end types.

-419 MW

for all Miter Welds (SKEY WM or WMF).

-421 SOF, FLRC, FLRE

Slip on flange. All welds associated with flanges with SKEY FLSO, FLSJ, FOSO.

-422 SOB

set-on (fabricated) branch. Set-on Tees. Set-on Cross. Teed Bends/ Elbows where Branch is made from pipe. Teed reducer where branch is made from pipe.

-423 LET

at all positions where "LET" type fittings are used to form a branch, and half coupling type fittings (o’let, latrolet, elbolet, half couplings).


-451 TAPPING CONNECTION

B-75

Output along with coordinate values at the tapping point on a user defined fitting. Requires option switch 122 to be set to 1 for tapping coordinates output on the isometric drawing.

-452 UNACCEPTABLE SPLIT Indicates that an unacceptable drawing split point has been found in the Tube. When used, the message is output in the top left-hand corner of each affected drawing. -454 CONNECTION Used at undeveloped Set-On Tees and Olets (which have no branch leg and ORIENTATION are indicated in dotted form on the pipeline) where the intended branch connection is in a skewed direction. A program generated direction word will be appended to this text to form a composite message. -455 Blank

associated with the elevations output at the face of flanges when ISOGEN option switch 119 is set to 1 or 2. For example: ?$FLANGE FACE (where: ? = position for coordinate output $ = line feed.

-456 SEE DETAIL ?

Used to provide a cross-reference message for Detail Sketches. This AText appears on the drawing part of the isometric. The ? will be replaced by the identifying number or letter.

-457 MITRE ?

Used to identify Miter Welds. The ? is replaced by the MITRE angle.

-461 COLUMN$?

Identifies vertical steel work element. (SKEY VST*)

-467 GRID LINE$?

Identifies project gridline. (SKEY GRD*)

-468 ?

Used for miscellaneous user defined elements (SKEY XXX*). The default ? character causes any identification name associated with the miscellaneous reference to be used when no other AText setting is made.


Used to point to a Site Weld. Setting a value for this AText is optional.

-499 SHOP TEST WELD

Points to either a site weld or a field fit weld that requires a shop test weld to be performed at the same location. (That is, Welds with the key WSST or WFST).


Used to point to an Offshore Weld. Setting a value for this AText is optional.

-502 SUPPORT

Used to indicate the orientation of a pipe support.

-541 _N

Used as a delimeter/identifier in General Note names.

-542 _S

Used as a delimeter/identifier in Specific Note names.


Alternative Texts Listed by Category The Isometric Drawing Area -201 E

denotes East at coordinates.

-202 N

denotes North at coordinates.

-203 W

denotes West at coordinates.

-204 S

denotes South at coordinates.

-205 EL +

denotes a positive Elevation at coordinates.

-206 EL -

denotes a negative Elevation at coordinates.

-207 NS

denotes the pipe Nominal Size

-208 CONN. TO

denotes CONNected TO where a pipe end is connected to a Nozzle.

-209 CONT. ON

denotes CONTinued ON where a pipe end is continued on another Pipeline or another drawing when a pipeline is split onto two or more drawings.

-210 F

denotes Flange. The letter used in the material list pointer for flanges.

-211 G

denotes Gaskets. The letter used in the material list pointer for gaskets.

-212 B

denotes Bolts. The letter used in the material list pointer for bolts.

-213 SPINDLE

used to give a spindle direction of a valve when it is not in a primary direction.

-214 MM

denotes Millimeters, used for arrowed dimensions on Angle and Multi-way Valves.

-215 REDUCING FLANGE

Message is pointed at each Reducing Flange.

-216 OFFSET

This message is used where an offset occurs (i.e., at Eccentric Reducers, Offset Reducing Flanges, Offset Blocks).

-217 MITER

This message is used where a Mitered Bend occurs.

-218 LOBSTER

This message is used where a Lobster Back Bend occurs.

-219 REINFORCED

Message is pointed at each reinforced Tee or Cross where the symbol key is TERF or CREF.

-220 LEFT LOOSE

Message is pointed at any Flange where LOOSE indicator is set.

-221 FFW

Message is pointed at any Field Fit Weld (i.e., Welds with key WF).

-222 FALL

denotes FALLing line.


If left blank, this AText automatically produces the degree symbol for falling lines specified with angle Fall indication. This symbol is used for Falling lines specified with a ratio (i.e., 1:10).


Appendix B: AText Facility - by Category

B-77


If left blank, this AText automatically produces the % symbol for Falling lines specified with a percentage.

-226 GRAD

is shown where a Falling line is specified in GRADS.

-227 PER M

is used where a falling line is specified as an incline in Metric units (i.e., Millimeters per Meter).

-228 PER FT

is used where a falling line is specified as an incline in Imperial units (i.e., Inches per Foot).

-229 SCREWED

Message is pointed at any pipe (tube) end that has been set to screwed in the END intermediate file.

-232 SPEC

Message is pointed at any place in the pipe where the Specification changes. The name of the new Specification is automatically included.

-236 S

is used to denote that a Support exists as a component (i.e., S22 enclosed in a box).

-237 "

is the Inch indicator.

-238 ’

is the Feet indicator.


This AText is by default blank and can be used to produce a message at any open-ended pipe that is identified by a -33 record.


This AText is by default blank and can be used to produce a message at any open-ended pipe that is identified by a -36 record.


This AText is by default blank but is set to any word (i.e., FLAT). Then, eccentric reducers in orthogonal piping have an indication of the orientation of their flat side. Note: By setting the -243 AText, the ATexts -244, -245, -246, -247, -248, and -249 are also used.

-244 UP


-245 DOWN


-246 NORTH


-247 SOUTH


-248 EAST


-249 WEST


-275 SWEPT TEE

Message is plotted and pointed to any tee whose symbol key starts with TS.

-276 CONT. FROM

denotes CONTinued FROM. This message is plotted wherever a pipeline is splitonto two or more drawings (i.e., CONT. FROM DRG1).

-277 ORIFICE FLANGE

Note: The -276 AText also uses AText -255 for the DRG text). Message is plotted and pointed to Orifice Flanges.

-278 DIAL FACE

Message is plotted next to Instruments Dials (symbol keys IDPL and IDFL)

B-78 PDS ISOGEN Reference Guide - August 1999 followed by relevant direction. See Note below. -279 L

denotes Lap joint stub end. The letter used in the material list pointer for LJSEs.

-280 TAPPING

Message is plotted at Orifice Plates followed by relevant direction. See Note below.

-281 TAIL

Message is plotted at Spectacle Blinds and Slip Plates followed by relevant direction. See Note below.

-282 WINDOW

Message is plotted at Site Glass followed by relevant direction. See Note below. Note: AText Numbers -278, -280, -281 and -282 are only output if a primary direction is set in Word 14 of the component record. The appropriate direction (as defined by ATexts -244 to -249) is appended to the specific fitting text (i.e., DIAL FACE WEST).

-283 FLAT

This AText is used to indicate the orientation of the flat side of an eccentric reducer, when the reducer is in a skew. The contents of this AText is output in front of the contents of the -40 record containing the Flat direction. Note: The following six ATexts are used to output directions (in conjunction with other ATexts) on items that carry a direction setting in Word 14 of the component record in the intermediate file.

-284 TEE BEND

used to denote a Tee Bend.

-285 RATING FLANGE

Message is a facility to provide an extra message at a Flange to show different rating. This is done by giving the mating Gasket a symbol key of the required rating (i.e., 300#). Only used for fixed-length piping.


This AText is set to blank by default; however, if set, outputs message on screwed erection fittings.

-287 ORIENTATION DIRECTION

Message on offset o’lets is followed by the direction of the off-line leg.

-288 PIPE

used on System Isometrics to denote position(s) of change in Pipeline Reference.

-298 TEE ELBOW

used to denote a Tee Elbow.

-338 BEND RADIUS

used to denote a bend radius for a pipe bend.

-349 PP

Is used to indicate Personal Protection type insulation on Insulation Indication symbols having the symbol key 'INPP".

-350 REDUCING ELBOW

Is used to indicate a REDUCING ELBOW on fittings having the symbol key ER**.

-450 B.O.P.

If used with the correct record type (i.e., -27), this message, along with B.O.P. elevation from record -27, is printed on the isometric.


B-79

-451 TAPPING CONNECTION

Output along with coordinate values at the tapping point on a user defined fitting. Requires option switch 122 to be set to 1 for tapping coordinates output on the isometric drawing.

-452 UNACCEPTABLE SPLIT

Indicates that an unacceptable drawing split point has been found in the Tube. When used, the message is output in the top left-hand corner of each affected drawing.

-454 CONNECTION ORIENTATION

Used at undeveloped Set-On Tees and Olets (which have no branch leg and are indicated in dotted form on the pipeline) where the intended branch connection is in a skewed direction. A program generated direction word will be appended to this text to form a composite message.

-455 BLANK ISOGEN

associated with the elevations output at the face of flanges when ISOGEN option switch 119 is set to 1 or 2. For example: ?$FLANGE FACE (where ? = position for coordinate output $ = line feed)

-456 SEE DETAIL ?

Used to provide a cross-reference message for Detail Sketches. This AText appears on the drawing part of the isometric. The ? will be replaced by the identifying number or letter.

-457 MITRE ?

Used to identify Mitre Welds. The ? is replaced by the mitre angle.

-461 COLUMN$?

Identifies vertical steel work element. (SKEY VST*)

-467 GRID LINE$?

Identifies project gridline. (SKEY GRD*)

-468 ?

Used for miscellaneous user defined elements (SKEY XXX*). The default ? character causes any identification name associated with the miscellaneous reference to be used when no other AText setting is made.


Used to point to a Site Weld. Setting a value for this AText is optional.

-499 SHOP TEST WELD

Points to either a site weld or a field fit weld that requires a shop test weld to be performed at the same location. (That is, Welds with the key WSST or WFST.)

-501

(default blank)

Used to point to an Offshore Weld. Setting a value for this AText is optional.

-502

SUPPORT

Used to indicate the orientation of a pipe support.

-541 _N

Used as a delimeter/identifier in General Note names.

-542 _S

Used as a delimeter/identifier in Specific Note names.


Specification Change Indication The following ATexts are used for indication of Specification Changes on the isometric drawing: -290 INSUL

used to indicate INSULATION Spec. change. Content of -15 record appended.

-291 TRACE

used to indicate TRACING Spec. change. Content of -16 record appended.

-292 PAINT

used to indicate PAINTING Spec. change. Content of -17 record appended.

-289 MATL

used to indicate PIPING MATERIAL Spec. change. Content of -26 record appended.











The Title Block Area -250 DATE

This is used in the title block and the actual date is automatically appended in the required format (whether UK, EUR or USA). This AText also uses ATexts -258, -259, -269, -261, -262, -263, -264, -265, -266, -267, -268, -269 if the date format is set to UK.

-251 PROJECT NO.

This is used in the title block if the Project Number has been set in a -9 record.

-252 BATCH REF

This is used in the title block area if some form of reference has been set in a -10 record.

-253 PIPING SPEC

This is used in the title block area and the content of a -11 record is appended

-254 ISS


-255 DRG

This is only used when a pipe is split and this AText is used with AText -256 to indicate DRG n OF n (for example, drawing 1 of 1). Also used by AText 276.

-256 OF



B-81

-257 SPL

denotes a SPOOL drawing. A sequential number starting at one end of each pipe is automatically appended.

-258 JAN


-259 FEB


-260 MARCH


-261 APR


-262 MAY


-263 JUN


-264 JUL


-265 AUG


-266 SEP


-267 OCT


-268 NOV


-269 DEC


-270 THERMAL INSULATION SPEC


-271 TRACING SPEC


-272 PAINTING SPEC


-351 DRG$

generates DRG nl 1 of 2. This is done by replacing DRG$ with SHT$. With this configuration, SHT (or sheet) nl 1 of 2 is available.

The Plotted Material and Pipe Cut Lists Heading Texts -300 FABRICATION MATERIALS

is the heading under which components required for ’SHOP’ fabrication are listed. Word 14 of component record set to 1.

-301 PT

is the part number pointer used with AText -302.

-302 NO


-303 COMPONENT

is the heading in the material listing under which components are described according to their catalogue component description.

-304 N.S.

denotes Nominal Size.

-305 ITEM CODE

is the heading under which component identification codes are listed.

B-82 PDS ISOGEN Reference Guide - August 1999 -306 QTY

denotes Quantity required.

-307 PIPE

is the subheading under which Pipe is listed.

-308 FITTINGS

is the subheading under which Pipe Fittings (i.e., elbows, tees, etc., are listed.

-309 FLANGES

is the subheading under which all Flanges are listed.

-310 ERECTION MATERIALS

is the heading under which components required for ’SITE’ erection are listed. Word 14 of component record set to 2.

-311 GASKETS

is the subheading under which all Gaskets are listed

-312 BOLTS

is the subheading under which all Bolts are listed

-313 VALVES / IN-LINE ITEMS

is the subheading under which all Valves and In-line Items are listed.

-314 INSTRUMENTS

is the subheading under which all Instruments are listed. This AText should be used whenever the ’GROUP’ facility is used as a data item on STYLE 2 or STYLE 3 material lists. This AText allows you to set an abbreviation text that is used in the designated column for each component listed

-315 SUPPORTS

is the subheading under which all Supports are listed. This AText should be used whenever the ’GROUP’ facility is used as a data item on STYLE 2 or STYLE 3 material lists. This AText allows you to set an abbreviation text that is used in the designated column for each component listed.

-316 PIPE SPOOLS

is the subheading under which all Spool Numbers are listed.

-319 CUT PIPE LENGTHS

is the heading under which all the Cut Pipe Lengths are listed.

-320 PIECE

is the subheading to AText -319 under which the Cut Pipe piece numbers are listed. This AText is used with AText -321.

-321 NO

used with AText -320 to form a composite heading.

-322 CUT

is the subheading to AText -319 under which the actual Cut Pipe Lengths are listed. This AText is used with AText -323.

-323 LENGTH

used with AText -322 to form a composite heading.

-324 REMAR KS

is the subheading to AText -319 under which one of the ATexts -326, -327, or -32, if applicable, is listed.

-326 PLD BEND

denotes Pulled BEND remark that is listed under AText -324 if a Cut Pipe Length contains a pulled bend.

-327 LOOSE FLG

is a remark that is listed under AText -324 if a Cut Pipe Length has a loose flange attached.

-328 FF WELD

denotes the Fitted Field Weld remark that is listed under AText -324 if a Cut Pipe Length contains a Fitted Field Weld.


B-83

-329 M

denotes lengths of Pipe are in METERS.

-330 INS

denotes Nominal Sizes are in INCHES.

-331 MM

denotes the Nominal Sizes are in MILLIMETERS.

-334 S

is used with Fixed Length Piping and the contents of this AText (default S) is appended to the item code when one end of the Fixed Length spool has a special flange.

-335 WITH SPECIAL RATING FLANGE(S) (SEE ISO)

is used with Fixed Length Piping and the contents of the AText are appended to the description. Used with AText -334.

-339 MISCELLANEOUS COMPONENTS

is the subheading under which miscellaneous components are listed. This AText should be used whenever the ’CATEGORY’ facility is used COMPONENTS as a data item on STYLE 2 or STYLE 3 Material Lists. This AText also allows you to set an abbreviation text that is used in the miscellaneous column for each component listed.

-340 INDUCTION BEND ID

used to identify pipe required in the fabrication of induction bends. The induction bend tag is appended to the AText to form a complete string.


This AText is available as an alternative to the AText used when generating a Material List over flow at the bottom of the master drawing Material List (combination of ATexts -206 and -255). Any AText set by the user will have a program generated cross reference drawing number appended to it.


This AText is available as an alternative to the AText used when generating a Material List over flow at the top of the overflow Material List drawings(combination of ATexts -276 and -255). Any AText set by the user will have a program generated cross reference drawing number appended to it.

-352 WEIGHT

column heading on Material List.

-353 KGS

unit indication at all positions where weight is output. (used with ISOGEN switch 41 position D).

-354 LBS

unit indication at all positions where weight is output.(used with ISOGEN switch 41 position D).

-355 TOTAL

weight subtotal identifiers. This AText must be set to BLANK if this type of output PIPELINE is not required.

-356 U

used to identify all Pulled Bends. Used on the ISO and the material list as ’U3’.

-357 B

used to identify all ERECTION type Welds (on ISO and Material List) when positions F/G for option 73 are defined.


-358 W

used to identify all FABRICATION type Welds (on ISO and Material List) when positions F/G for option 73 are defined.

-359 Blank by Default

Bolt size x Length headings. Used with option switch 65 (Material Control File Only). A suggested setting is "DIA x LENGTH". If this AText is not blank, ISOGEN outputs in Bolt Diameter x Bolt Length order. Bolt Units are indicated immediately below this heading using a program-generated text string using a combination of ATexts -330 (INS) and -331 (MM) depending on the settings for option switch 65. For example: DIA x LENGTH (INS x INS).

-371 OFFSHORE MATERIALS

Material List main heading for offshore items. All materials sorted this new category as for other two categories (where appropriate).

-373 REM

Remarks Column heading in Material List.

-374 ANGLE

used with description of Pulled Bends in the material list. Bend angle is output when using ISOGEN option 23 set to 20 or 21. is the subheading under which welds are listed. This AText should be used whenever the ’CATEGORY’ facility is used as a data item on STYLE 2 or STYLE 3 Material Lists. This AText allows you to set an abbreviation text that is used in the weld column for each component listed.

-375 WELDS

-376 FAB

identification of FABRICATION material. To be used whenever the ’CATEGORY’ facility is used as a data item on STYLE 2 or STYLE 3 Material Lists. This AText allows the user to set an abbreviation text that is used in the fabrication column for each component listed.

-377 EREC

identification of ERECTION material. To be used whenever the ’CATEGORY’ facility is used as a data item on STYLE 2 or STYLE 3 Material Lists. This AText allows the user to set an abbreviation text that is used in the erection column for each component listed.

-378 OFF

identification of OFFSHORE material. To be used whenever the ’CATEGORY’ facility is used as a data item on STYLE 2 or STYLE 3 Material Lists. This AText allows the user to set an abbreviation text that is used in the offshore column for each component listed.

-379 TOTAL FABRICATION WEIGHT


-380 TOTAL ERECTION WEIGHT


-381 TOTAL OFFSHORE WEIGHT



B-85

The Line Summary Area The ATexts in the line summary area along the bottom of the isometric drawing can have their ATexts changed or made blank. If changed, the appropriate symbol for the AText is drawn. If made blank, the symbol is not drawn in the line summary area. -400 -401 -402 -403 -404 -405 -406 -407 -411

TRACED$PIPE LAGGED$PIPE PIPE$SUPPORT COMPN$JOINT SCREWED$JOINT SOCKET$WELD FIELD$WELD SHOP$WELD SITE$CONNECTION

The following ATexts appear in the line summary area along the bottom of both the plotted and printed Material Lists. -317 PIPE NS

is used with AText -318 to which the total Center Line Length per bore is automatically computed and listed.

-318 CL LENGTH -360 FT

is used with AText -317. used with the old style Material List in conjunction with AText -318 (See ISOGEN option 24).

-361 FT-INS

used with the new style Material List in conjunction with AText -318 (See ISOGEN option 24). is the subheading to AText -319. Describes the operations necessary to prepare the end for fabrication. End connections are listed for pipe (See ISOGEN option 2 setting 11 or 12, and see AText -366 through -370).

-362 END$ONE

-363 END$TWO

is the subheading to AText -319. Describes the operations necessary to prepare the end for fabrication (See ISOGEN option 2 setting 11 or 12, and see AText -366 through -370).

-365 Blank by Default

is the alternative last column subheading to AText -319 under which cut pipe item code is listed for pipe. When used for Part Number, a suggested setting is:"PART$NO" (see ISOGEN option 2 setting 11 or 12). If Part No. is required on the Cut List instead of ITEM CODE, then AText -364 should be set to ’blank’ and AText -365 set to required heading (i.e., PART$NO).

-366 SQ.CUT

used when not one of the four other end types (see ISOGEN option 2 setting 11 or 12).

-367 BEVEL

used for all Butt Welds (BW) Items that are treated as BWs, but do not have the BW end condition as part of their SKEY (see ISOGEN option 2 setting 11 or 12). Flanges: FLWN - Flange Weld Neck FOWN - Flange Orifice Weld Neck FLSE - LJSE Butt Weld Type All other flange type items use Square Cut (AText -366)

-368 SCREWED

used for all Screwed Ends (SC) (see ISOGEN option 2 setting 11 or 12).

-369 SHAPED

used for all Fabricated Branch connections (see ISOGEN option 2 setting 11 or 12).


-370 MITRED

used for all mitered ends at miter weld positions (see ISOGEN option 2 setting 11 or 12).

-410 [1] DENOTES PIPE SPOOL NO$ -1 DENOTES PARTS LIST NO

This is a general note that determines how Spool Numbers and Material List Part Numbers are shown on the isometric. For example: If only the bottom line is required the records in the intermediate file should be: -410 $ 1 DE‘NOTES -1 PARTS LIST NO

The Printed Material List The ATexts listed below are used in addition to all the ATexts listed for the Plotted Material and Pipe Cut Lists. -332 PAGE

has a Page Number automatically appended.

-333 PIPELINE REF

has the Pipeline Reference automatically appended.

-336 SYSTEM REF

is used as an alternative to AText -333 when producing Material List for System Isometric. Content of a -25 record is automatically appended.

The Weld Box Summary: Standard Weld Summary Box -372 REMARKS

Heading for "Remarks" box.

-410 [1] DENOTES PIPE SPOOL NO$ -1 DENOTES PARTS LIST NO

If only the bottom line is required, the records in the intermediate file should be: -410 $ 1 DENOTES -1 PARTS LIST NO

-411 SITE$CONNECTION -412 WELD|SHOP|WELD |WELDER|VISUAL|NOT |HARD|S.R|FAB.QA

weld header box details (line 1).

-413 NO |/FLD|PROC| ID |ACCEPT| NO| NO | |ACCEPT

continuation of weld box header details. (line 2)

-414 S

Fabrication/Shop Weld used in the Weld Category identification on the Old Style Weld Box. When using all three weld types AText -412 and -413, column 2 probably is changed to give a heading that covered all types. For example: WELD CAT

-415 F

Erection/Field/Site Weld used in the Weld Category identification on the Old Style Weld Box.

-416 O

Offshore Weld used in the Weld Category identification on the Old Style Weld Box.


B-87

The Weld Box Summary: User-Defined Weld Summary Box -417 BW

for All Butt Welds. All fittings with BW end type in addition to: LWN and FOWN flanges LSE and LJSE type flanges.

-418 SW

or all Socket Welds. All fittings with SW end types.

-419 MW

or all Miter Welds (SKEY WM or WMF).

-421 SOF

slip on flange. All welds associated with flanges with SKEY FLSO, FLSJ, FOSO, FLRC, FLRE.

-422 SOB

set-on (fabricated) branch. Set-on Tees. Set-on Cross. Teed Bends/Elbows where Branch is made from pipe. Teed reducer where branch is made from pipe.

-423 LET

at all positions where "LET" type fittings are used to form a branch, and half coupling type fittings (o’let, latrolet, elbolet, half couplings).


Appendix C: Example Documents C - 1

Appendix C

__________________________________________________________________________________________________________________________________________________

Example Documents

C-2



Appendix C

__________________________________________________________________________________________________________________________________________________

Example Documents This section contains sample iso extraction documents including: Options File (#/dat/isoc.def) Label Library Label Definitions (as user-defined in the Options File) HITS Report (.h file) Intermediate Data File (.idf file) Interface Error Log (.err file) MTO Neutral File (.b# file) ISOGEN Message File (.msg file) ISOGEN Printed Parts File (.prt file) ISOGEN Component vs Sheet Number File (.sed file) ISOGEN Cut Pipe Report (.cut file) Title Block Table (.bit, .seg and .dwg files)

C-4


C.1 The Options File (#/dat/isoc.def) __________________________________________________________________________________________________________________________________________________ ! DEFINE ZX_ISOC.DEF ! Description= Definition of the ISOGEN defaults file for size C batch isos ! Rev=

By=

Ckd By=

Date=22-May-1991

! ISOGEN_OPTIONS_BLOCK 10

!10 lines follow

3275

0

1

1

1000

3

0

10

0

28

10

15

15

6

457

610

1

1

4

1

0

0

0

0

1

0

1

10

! 1-14 ! 15-28

105

0

0

100

0

100 46046

1

0

100

0

0

1

3

! 29-42

1

1

1

1

1

1

1

1

1

0

0

0

0

0

! 43-56

0

0

1

1

1

2

62

1

0

0

0

0

0

0

! 57-70

8000

0

0

0

0

0

1

0

0

0

0

0

0

0

! 71-84

0

0

0

0

0

0

0

0

0

0

0

0

0

0

! 85-98

0

0

0

0

0

0

0

0

0

0 100000

0

1

0

! 99-112

0

1

0

250

0

0

0

70

1

0

5

0

0

0

! 113-126

0

0

0

0

0

0

0

0

0

0

0

0

0

0

! 127-140

INTERGRAPH_OPTIONS_BLOCK 6

!6 lines follow 0

0

0

1

0

1

1

0

10

0

20

10

1

0

! 1-14

0

2

1

0

1

1

0

1

1

0

0

0

1

0

! 15-28

0

1

0

1

1

1

0

0

1

0

1

0

1

0

! 29-42

0

0

3

0

0

0

0

0

0

0

0

0

0

0

! 43-56

0

0

0

0

0

0

0

0

0

0

0

0

0

0

! 57-70

0

0

0

0

0

0

0

0

0

0

0

0

0

999

! 71-84

FILES 14

!14 LINES TO FOLLOW

’c:\win32app\ingr\pdiso\dat\isomap.tbl’

!PDS TO ISOGEN MAP

’c:\win32app\ingr\pdiso\dat\symbol.lib’

!USER DEFINED SYMBOL LIB

’ ’

!LABEL DESCRIPTION LIBRARY

’ ’

!VALVE / OPERATOR TABLE

’c:\win32app\ingr\pdiso\dat\isomto.tbl’

!MTO RECORD MAP

’ ’

!RESERVED

’c:\win32app\ingr\pdiso\dat\isoc.blk’

!TITLE BLK TABLES FILE

’ ’

!SEGMENT DATA TABLE

’ ’

!RESERVED

’ ’

!DETAIL SKETCH CELL LIBRARY

’ ’

!DRAWING DEFINITION FILE (DDF)

’ ’

!WELD DEFINITION FORMAT FILE (WDF)

’ ’

!MATERIAL LIST DEFINITION FILE (MLD)

’ ’

!BENDING PARAMETERS OUTPUT FILE

PIPELINE_HEADER 13 -6, -7, -11,

!13 lines follow 12, -2, 0,

0,

’’,

’’,

0,

0,

0,

0,

0,

0,

0,

0,

0 !Line ID label record/break

0, 955,

12, 12,

’’,

’-’,

0,

0,

0,

0,

0,

0,

0,

0,

0 !Piece mark prefix record

0,

’’,

’’,

0,

0,

0,

0,

0,

0,

0,

0,

0 !Piping materials class record/break

0,

’’,

’’,

0,

0,

0,

0,

0,

0,

0,

0,

0 !Date record

-14,

0,

0,

-15,

0,

0, 956,

’’, ’INSUL’,

0,

0,

0,

0,

0,

0,

0,

0, 957 !Insulation record/break

0,

0, 958,

-16,

’’, ’TRACE’,

0,

0, 959,

0,

0, 984,

0,

0, 960 !Heat tracing reqmts record/break

-17,

12, 40,

0,

’’,

’’,

0,

0,

0,

0,

0,

0,

0,

0,

-41,

12,

0,

’’, ’PKGNO’,

0,

0,

0,

0,

0,

0, 67, 42,

0 !Packaged system no break

-42,

12, 23,

0, ’PER SPEC’,

’’,

0,

0,

0,

0,

0,

0,

0 !Sch/thk override break

-43,

12, 41,

0,

’’, ’CLEAN’,

0,

0,

0,

0,

0,

0, 67, 39,

0 !Cleaning reqmts break

’’,

0,

0,

0,

0,

0,

0,

0 !Testing reqmts break

-44, -45,

0,

7,

0, 961,

’’,

0,

0,

0,

0,

0 !Coating reqmts record/break

12, 21,

0,

’’,

’’, 34, 33,

0, 50, 28,

0, 67, 30,

0 !Hold status break

-99, -12, 20,

0,

’’,

’’, 34, 32,

0, 50, 27,

0, 67, 29,

0 !Construction status label

ATEXT_SPECIFICATIONS 70 -207, ’NPD’

!70 lines follow !Nominal pipe diameter callout


-208, ’CONN TO’

!Nozzle connection callout

-209, ’SEE ISO’

!Iso/Sheet continued on callout

-213, ’STEM’

!Spindle callout

-215, ’ ’

!Remove reducing flange callout

-217, ’ ’

!Remove miter callout

-218, ’ ’

!Remove lobster callout

-219, ’ ’

!Remove reinforcing pad callout

-220, ’ ’

!Remove loose component callout

-221, ’FFW’

!Field Fit Weld callout

-222, ’SLOPE’

!Slope callout

-243, ’FLAT SIDE’

!Eccentric reducer flat side callout

-244, ’U’

!Up orientation callout

-245, ’D’

!Down orientation callout

-246, ’N’

!North orientation callout

-247, ’S’

!South orientation callout

-248, ’E’

!East orientation callout

-249, ’W’

!West orientation callout

-250, ’ ’

!Remove date from ISOGEN title block

-253, ’ ’

!Remove piping materials class from ISOGEN title block

-255, ’SHT’

!Iso continuation prefix

-270, ’ ’

!Remove insulation from ISOGEN title block

-271, ’ ’

!Remove heat tracing from ISOGEN title block

-272, ’ ’

!Remove coating from ISOGEN title block

-276, ’SEE SHT’

!Sheet continued from callout

-277, ’ ’

!Remove orifice flange callout

-278, ’ ’

!Remove dial face orientation callout

-282, ’ ’

!Remove sight glass window orientation callout

-284, ’ ’

!Remove tee bend callout

-287, ’ORIENT’

!Skewed olet orientation callout

-288, ’LINE :’

!Line ID break (-6) callout

-289, ’CLASS:’

!PMC break (-11) callout

-290, ’INSUL:’

!Insulation reqmts break (-15) callout

-291, ’TRACE:’

!Heat tracing reqmts break (-16) callout

-292, ’COAT :’

!Coating reqmts break (-17) callout

-293, ’PKGNO:’

!Packaged system no break (-41) callout

-294, ’SCH

!Sch/thk override break (-42) callout

:’

-295, ’CLEAN:’

!Cleaning reqmts break (-43) callout

-296, ’TEST :’

!Testing reqmts break (-44) callout

-297, ’STAT :’

!Hold status break (-45) callout

-298, ’ ’

!Remove tee elbow callout

-300, ’SHOP MATERIALS’

!Shop materials callout in BOM

-303, ’DESCRIPTION’

!Description callout in BOM

-304, ’NPD’

!Nominal pipe diameter callout in BOM

-305, ’CMDTY CODE’

!Commodity code callout in BOM

-307, ’ ’

!Remove pipe callout in BOM

-308, ’ ’

!Remove fittings callout in BOM

-309, ’ ’

!Remove flanges callout in BOM

-310, ’OTHER THAN SHOP MATERIALS’

!Other than shop materials callout in BOM

-311, ’ ’

!Remove gaskets callout in BOM

-312, ’ ’

!Remove bolts callout in BOM

-313, ’ ’

!Remove valves callout in BOM

-314, ’INSTRUMENTS’

!Instruments callout in BOM

-315, ’PIPE SUPPORTS’

!Pipe supports callout in BOM

-316, ’PIECE MARKS’

!Pipe marks callout in BOM

-317, ’ ’

!Remove pipe NPD callout from title block

-318, ’ ’

!Remove centerline length callout from title block

-330, ’IN’

!NPD units callout in BOM

-400, ’ ’

!Remove tracing legend from title block

-401, ’ ’

!Remove insulation legend from title block

-402, ’ ’

!Remove pipe support legend from title block

-403, ’ ’

!Remove compression joint legend from title block

-404, ’ ’

!Remove screwed joint legend from title block

-405, ’ ’

!Remove socketweld joint legend from title block

-406, ’ ’

!Remove field welded joint legend from title block

-407, ’ ’

!Remove shopwelded legend from title block

C-6


-410, ’ ’

!Remove pipe spool nos from title block

-411, ’ ’

!Remove site connection legend from title block

-451, ’ ’

!Tapping Connection Note

-498, ’FW’

!Field weld (no added material)

START_POINT_NOTES 1

!1 line follows

0, 12, 310,

0

!Line ID label at start of line

TYPE_1_LABELS 5

!5 lines follow

1, 34, 46, 962

!Piping commodity component remark label

2, 34, 46, 962

!Piping specialty component remark label

4, 67, 52, 963

!Instrument remark label

3,-50, 26, 966

!Cold spring label

3, 50, 38, 986

!Pipe remark label

TYPE_2_LABELS 22

!22 lines follow

34,

3, ’6Q3C82’, 0, 967

!RWELD size

34,

3, ’6Q2C11’, 0, 968

!Operate 6Q2C11 in closed position

34,

3, ’6Q2C12’, 0, 968


34,

3, ’6Q2C13’, 0, 968


34,

3, ’6Q2C10’, 0, 969

!Operate 6Q2C10 in open position

34,

3, ’6Q2C15’, 0, 969

!Operate 6Q2C15 in open position

34,

3, ’6Q3C81’, 0, 997

!Non-radial offset label

34,

3, ’6Q3C83’, 0, 997


34,

3, ’6Q3C85’, 0, 997


34,

3,

’6Q1C’, 4, 964

!Piping commodity valves opening action label

34,

3,

’6P6C’, 4, 964

!Piping specialty components opening action label

34,

3,

’6Q6C’, 4, 964

!Piping specialty components opening action label

67,

3,

’7P1E’, 4, 965

!Instrument opening action label

67,

3, ’7P2C01’, 0, 987

!7P2C01 press set pt label

67,

3, ’7P2C06’, 0, 987


67,

3, ’7P2C09’, 0, 988

!7P2C09 vac set pt label

67,

3, ’7P2C12’, 0, 989

!7P2C12 press/vac set pt label

67,

3, ’7P2C14’, 0, 989

!7P2C14 press/vac set pt label

67,

3, ’7P2C16’, 0, 987


67,

3, ’7P2C18’, 0, 988

!7P2C18 vac set pt label

67,

3,

’7P3C’, 4, 965

!Instrument opening action label

80, 16,

’3’, 0, 978

!Pipe support existing construction status label

TYPE_3_LABELS 0

!0 lines follow

NOZZLE_NOTE 5

!5 lines follow

-1, -21, 952

!Equip no (concatenated with label 953)

-1, -22, 953

!Nozzle no

1,

22, 954

!NPD-prep-rating for bolted nozzles

2,

22, 954

!NPD-prep-rating for FEM nozzles

3,

22, 950

!NPD-prep for MAL nozzles

SECONDARY_ORIENTATION_NOTE 24

!To define operators requiring secondary orientation !24 lines follow

’OP9’,

’’

!SN=OP9

’OP_271’,

’’

!SN=OP_271

’OP_291’,

’’

!SN=OP_291

’OP_311’,

’’

!SN=OP_311

’OP_331’,

’’

!SN=OP_331

’OP_332’,

’’

!SN=OP_332

’OP_333’,

’’

!SN=OP_333

’OP_334’,

’’

!SN=OP_334

’OP_351’,

’’

!SN=OP_351

’OP_391’,

’’

!SN=OP_391

’OP_413’,

’’

!SN=OP_413

’OP_452’,

’’

!SN=OP_452

’OP_491’,

’’

!SN=OP_491

’OP_493’,

’’

!SN=OP_493

’OP_494’,

’’

!SN=OP_493

’OP_571’,

’’

!SN=OP_571


’OP_572’,

’’

!SN=OP_572

’OP_573’,

’’

!SN=OP_573

’OP_574’,

’’

!SN=OP_574

’OP_711’,

’’

!SN=OP_711

’OP_811’,

’’

!SN=OP_811

’OP_853’,

’’

!SN=OP_853

’OP_854’,

’’

!SN=OP_854

’OP_931’,

’’

!SN=OP_931

DOTTED_SYMBOLOGY_CODE_LIST_VALUES 1

!1 line follows

12, 20, 34, 32, 50, 27, 67, 29, 6, 3, 4, 5, 6, 7, 8

!Construction status (CL130)

NOMTO_CODE_LIST_VALUES 1

!1 line follows

12, 20, 34, 32, 50, 27, 67, 29, 6, 3, 4, 5, 6, 7, 8

!Construction status (CL130)

SHOP_FABCAT_CODE_LIST_VALUES 1 6,

!1 line follows 5,

15, 25, 35, 45, 95

!Shop fabricated codelist values from CL180

END_POINT_COMPONENT_LABELS 1

!1 line follows

’’, 12,

0, 951,

12, 0, 951,

12, 0, 951

!Line ID + dgn area

LINE_ID_DEFINITION 1 12,

!1 lines follow 3, ’’

!Line ID

MOVABLE_TEXT 10

!10 lines follow:

-6,

25,

5,

1,

0,

0,

0

!Relocate -6 record to lower left corner of iso

-25,

0,

0,

0,

0,

0,

0

!Relocate -25 record to outside of iso border

-41,

0,

0,

0,

0,

0,

0


-42,

0,

0,

0,

0,

0,

0


-43,

0,

0,

0,

0,

0,

0


-44,

0,

0,

0,

0,

0,

0


-45,

0,

0,

0,

0,

0,

0


-700, 42790, 43390,

0,

0,

0,

0

!Relocate N arrow to upper right quadrant of iso

-702,

0,

0,

0,

0,

0,

0

!Relocate ISOGEN sheet no callout

-703,

0,

0,

0,

0,

0,

0

!Relocate ISOGEN sheet no callout

NEW_SYMBOL_KEYS 0

!0 lines follow

GENITM_NOTE_FORMAT 4

!4 lines follow

’CHAINWHEEL$WITH [2] CHAIN’

!Length of chain note

’PROVIDE FLOOR STAND$WITH Y1=[2]’

!Floorstand note

’PROVIDE EXTENSION STEM$WITH Y1=[2]’

!Extension stem note

’ ’

!Turn off note for implied materials

ALTERNATE_DESCRIPTION_INDEX 3

!3 lines follow

2, 34,

0,

971

!To access ZX_SPCLTYDESCR.LIB specialties

5, 80,

0,

972

!To access ZX_SPCLTYDESCR.LIB for pipe supports

4, 67,

0,

973

!To access ZX_SPCLTYDESCR.LIB for instruments

INGR_ATEXT_SPECIFICATIONS 15

!15 LINES TO FOLLOW

1, ’NOT FOUND’, ’’

!Used based on Intergraph option 6 and ATEXT -209

2, ’BOLT LENGTH’, ’’

!Used based on Intergraph option 58

3, ’NUTS PER BOLT’, ’’


4, ’CHAIN_’, ’’

!Used based on Intergraph option 33,56

5, ’FSTAND_’, ’’


6, ’XSTEM_’, ’’


7, ’HOR’, ’’

!Horizontal - Used for an operator in a 2plane ske

8, ’VOR’, ’’

!Vertical - Used for an operator in a 2plane ske

9, ’DEG’, ’’

!Degree - Used for an operator in a 2plane ske

10, ’E’, ’’

!Used with skewed operator orientation notes

11, ’N’, ’’


12, ’U’, ’’


13, ’W’, ’’


14, ’S’, ’’


15, ’D’, ’’


C-8


USER_DEFINED_WELDS 3 10, 11,12,13,14,15,16,17,18,19,20,1,"WW"

!Weld types 11-20 are shop welds

2, 21,22, 2, "WS"

!Weld types 21, 22 are field welds

1, 24, 2, "WF"

!Weld type 24 is a field fit weld


C.2 Label Library Label Definitions __________________________________________________________________________________________________________________________________________________ **************** Label Type = 400 ****************

Label Name = Comp cmdty code

[1]

Piping Component Data

[1]

commodity_code

- Character (16)

***************************************

**************** Label Type = 401 ****************

Label Name = Pipe sch/thk 1

[1]

Piping/Tubing Data

[1]

schedule_thickness - Character (8)

***************************************

**************** Label Type = 402 ****************

Label Name = Tag no

[1]

Instrument Component Data

[1]

instrument_comp_no - Character (20)

***************************************

**************** Label Type = 403 ****************

Label Name = Comp sch/thk 1

[1]


[1]

cp_1_sch_thk

- Character (8)

***************************************

**************** Label Type = 404 ****************

Label Name = Reserved

Dummy

Attribute Data

C - 10

1


- ’Dummy’

***************************************

**************** Label Type = 405 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 406 ****************

Label Name = Comp sch/thk 1 b

[1] bore


[1] 2

cp_1_sch_thk

- Character (8)

- ’ bore’

***************************************

**************** Label Type = 407 ****************

Label Name = Comp sch/thk 2

[1]


[1]

cp_2_sch_thk

- Character (8)

***************************************

**************** Label Type = 408 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 409 ****************

Label Name = Comp sch/thk 2 b

[1] bore


[1] 2

cp_2_sch_thk - ’ bore’

- Character (8)


***************************************

**************** Label Type = 410 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 411 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 412 ****************

Label Name = Comp sch/thk 1x2

[1] x [3]


[1] 2

cp_1_sch_thk

- Character (8)

- ’ x ’

[3]

cp_2_sch_thk

- Character (8)

***************************************

**************** Label Type = 413 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 414 ****************

Label Name = Comp sch/thk 1x2 b

[1] x [3] bore


[1] 2 [3] 4

cp_1_sch_thk

- Character (8)

- ’ x ’ cp_2_sch_thk - ’ bore’

- Character (8)

C - 12


***************************************

**************** Label Type = 415 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 416 ****************

Label Name = Comp sch/thk 1x3

[1] x [3]


[1] 2

cp_1_sch_thk

- Character (8)

- ’ x ’

[3]

cp_3_sch_thk

- Character (8)

***************************************

**************** Label Type = 417 ****************

Label Name = Comp sch/thk 1x3 b

[1] x [3] bore


[1] 2

cp_1_sch_thk

[3] 4

- Character (8)

- ’ x ’ cp_3_sch_thk

- Character (8)

- ’ bore’

***************************************

**************** Label Type = 418 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 419 ****************


Dummy

Attribute Data


1

- ’Dummy’

***************************************

**************** Label Type = 420 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 421 ****************

Label Name = Bonnet length

[1]


[1]

dimension_a

- Real (6.4) with sub units (ex. ",IN,MM,etc.)

***************************************

**************** Label Type = 422 ****************

Label Name = Piping chain length

[1]


[1]

bend_angle


***************************************

**************** Label Type = 423 ****************

Label Name = RWELD size

[1]


[1]

bend_radius


***************************************

**************** Label Type = 424 ****************

Label Name = Instr chain length

[1]


[1]

chain_length


***************************************

C - 14


**************** Label Type = 425 ****************

Label Name = RPAD width x thick

[1] x [3]


[1] 2

operator_weight


- ’ x ’

[3]

bend_radius


***************************************

**************** Label Type = 426 ****************

Label Name = Comp NPD 1

[1]


[1]

cp_1_nom_pipe_diam - Character (9)

***************************************

**************** Label Type = 427 ****************

Label Name = Monitor elev length

[1] nominal height


[1] 2

dimension_a


- ’ nominal height’

***************************************

**************** Label Type = 428 ****************

Label Name = Hydrant cover

[1] cover


[1] 2

dimension_a


- ’ cover’

***************************************

**************** Label Type = 429 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************


**************** Label Type = 430 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 431 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 432 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 433 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 434 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 435 ****************


C - 16


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 436 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 437 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 438 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 439 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 440 ****************


Dummy

Attribute Data


1

- ’Dummy’

***************************************

**************** Label Type = 441 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 442 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 443 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 444 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 445 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

C - 18


**************** Label Type = 446 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 447 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 448 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 449 ****************


Dummy

Attribute Data

1

- ’Dummy’

***************************************

**************** Label Type = 950 ****************

Label Name = MAL nozzle descr

[1] [3]

Nozzle Data

[1] 2 [3]

Entity 22 Attribute 3 - Character (9) - 1 space(s) Entity 22 Attribute 5 - Character (8)

***************************************

**************** Label Type = 951 ****************


Label Name = Iso continuation

[1][2]-[4][5]

Piping Segment Data

[1]

unit_code

- Character (2)

[2]

line_sequence_no

- Character (6)

3

- ’-’

[4]

fluid_code

[5]

design_area_number - Character (12)

- Character (5)

***************************************

**************** Label Type = 952 ****************

Label Name = Equip no

[1]/

Equipment Data

[1] 2

Entity 21 Attribute 1 - Character (30) - ’/’

***************************************

**************** Label Type = 953 ****************

Label Name = Equip nozzle

[1]

Nozzle Data

[1]

Entity 22 Attribute 1 - Character (10)

***************************************

**************** Label Type = 954 ****************

Label Name = BLT/FEM nozzle descr

[1] [3] [5]

Nozzle Data

[1] 2 [3] 4 [5]

Entity 22 Attribute 3 - Character (9) - 1 space(s) Entity 22 Attribute 5 - Character (8) - 1 space(s) Entity 22 Attribute 4 - Character (8)

***************************************

**************** Label Type = 955 ****************

Label Name = Pc mark prefix

[1][2]-[4][5]

Piping Segment Data

C - 20


[1]

unit_code

- Character (2)

[2]

line_sequence_no

- Character (6)

3

- ’-’

[4]

fluid_code

[5]

design_area_number - Character (12)

- Character (5)

***************************************

**************** Label Type = 956 ****************

Label Name = Segment insulation

[1] [3]

Piping Segment Data

[1] 2 [3]

insulation_purpose - Character (10) - 1 space(s) insulation_thick


***************************************

**************** Label Type = 957 ****************

Label Name = Instr insulation

[1] [3]


[1] 2 [3]

insulation_purpose - Character (10) - 1 space(s) insulation_thick


***************************************

**************** Label Type = 958 ****************

Label Name = Segment ht tracing

[1] [3] [5]

Piping Segment Data

[1] 2 [3] 4 [5]

heat_tracing_reqmt - Character (5) - 1 space(s) heat_tracing_media - Character (5) - 1 space(s) heat_tracing_temp

- Real (6.0)

***************************************

**************** Label Type = 959 ****************

Label Name = Comp ht tracing

[1] [3] [5]


[1] 2 [3] 4 [5]


- Real (6.0)


***************************************

**************** Label Type = 960 ****************

Label Name = Instr ht tracing

[1] [3] [5]


[1] 2 [3] 4 [5]


- Real (6.0)

***************************************

**************** Label Type = 961 ****************

Label Name = Segment testing

[1] [3] [5][6]

Piping Segment Data

[1] 2 [3] 4

test_system_no

- Character (6)

- 1 space(s) test_fluid

- Character (5)

- 1 space(s)

[5]

test_pressure

- Real (8.2)

[6]

nor_op_pres_units

- Character (10)

***************************************

**************** Label Type = 962 ****************

Label Name = Comp remarks

[1]


[1]

remarks

- Character (25)

***************************************

**************** Label Type = 963 ****************

Label Name = Instr remarks

[1]


[1]

remarks

- Character (25)

***************************************

**************** Label Type = 964 ****************

Label Name = Comp opening action

C - 22


[1]


[1]

opening_action

- Character (10)

***************************************

**************** Label Type = 965 ****************

Label Name = Instr opening action

[1]


[1]

opening_action

- Character (10)

***************************************

**************** Label Type = 966 ****************

Label Name = Pipe cold spring

Adjust length by [2] for$cold spring (-)/cut long (+)

Piping/Tubing Data

1 [2] 3

- ’Adjust length by ’ cold_spring_length - Real (7.4) with sub units (ex. ",IN,MM,etc.) - ’ for$cold spring (-)/cut long (+)’

***************************************

**************** Label Type = 967 ****************

Label Name = RWELD size

[1] RWELD


[1] 2

bend_radius


- ’ RWELD’

***************************************

**************** Label Type = 968 ****************

Label Name = Operate closed

Operate closed

Attribute Data

1

- ’Operate closed’

***************************************

**************** Label Type = 969 ****************

Label Name = Operate open


Operate open

Attribute Data

1

- ’Operate open’

***************************************

**************** Label Type = 970 ****************

Label Name = Pipe spt detail no

Per detail(s) [2]

Pipe Support Data

1

- ’Per detail(s) ’

[2]

Entity 80 Attribute -1 - Character (30)

***************************************

**************** Label Type = 971 ****************

Label Name = Spclty descr access

PSPECIALTY

Attribute Data

1

- ’PSPECIALTY’

***************************************

**************** Label Type = 972 ****************

Label Name = Pip spt descr access

PSUPPORT

Attribute Data

1

- ’PSUPPORT’

***************************************

**************** Label Type = 973 ****************

Label Name = Instr descr access

INSTR

Attribute Data

1

- ’INSTR’

***************************************

**************** Label Type = 977 ****************

Label Name = Segment P&ID nodes

[1]-[3]

C - 24


Piping Segment Data

[1] 2 [3]

PID_id_part_a

- Character (4)

- ’-’ PID_id_part_b

- Character (4)

***************************************

**************** Label Type = 978 ****************

Label Name = Pipe spt constr stat

[1]

Pipe Support Data

[1]

construction_stat

- Character (15)

***************************************

**************** Label Type = 979 ****************

Label Name = Unit no/Dgn area no

[1]/[3]

Piping Segment Data

[1] 2 [3]

unit_number

- Character (12)

- ’/’ design_area_number - Character (12)

***************************************

**************** Label Type = 980 ****************

Label Name = Segment module no

[1]

Piping Segment Data

[1]

module_no

- Character (16)

***************************************

**************** Label Type = 981 ****************

Label Name = Seg package sys no

[1]

Piping Segment Data

[1]

package_system_no

- Character (12)

***************************************

**************** Label Type = 982 ****************

Label Name = Seg matls of constr

[1]


Piping Segment Data

[1]

mater_of_construct - Character (6)

***************************************

**************** Label Type = 983 ****************

Label Name = Segment test fluid

[1]

Piping Segment Data

[1]

test_fluid

- Character (5)

***************************************

**************** Label Type = 984 ****************

Label Name = Pipe ht tracing

[1] [3] [5]

Piping/Tubing Data

[1] 2 [3] 4 [5]


- Real (6.0)

***************************************

**************** Label Type = 985 ****************

Label Name = Nozzle service

[1]

Nozzle Data

[1]

Entity 22 Attribute 16 - Character (20)

***************************************

**************** Label Type = 986 ****************

Label Name = Pipe remarks

[1]

Piping/Tubing Data

[1]

remarks

- Character (25)

***************************************

**************** Label Type = 987 ****************

Label Name = Press set pt

Press set pt: [2][3]

C - 26



1

- ’Press set pt: ’

[2]

chain_length

[3]


- Real (8.2)

***************************************

**************** Label Type = 988 ****************

Label Name = Vacuum set pt

Vac set pt: [2][3]


1

- ’Vac set pt: ’

[2]

Entity 67 Attribute -1 - Real (8.2)

[3]


***************************************

**************** Label Type = 989 ****************

Label Name = Press/vac set pt

Press set pt: [2][3] Vac set pt: [5][6]


1

- ’Press set pt: ’

[2]

chain_length

[3]


4

- Real (8.2)

- ’Vac set pt: ’

[5]

Entity 67 Attribute -1 - Real (8.2)

[6]


***************************************

**************** Label Type = 990 ****************

Label Name = Instr end prep

with end prep: [2] [4] [6]


1 [2] 3 [4] 5 [6]

- ’with end prep: ’ cp_1_end_prep

- Character (15)

- 1 space(s) cp_2_end_prep

- Character (16)


- Character (15)

***************************************

**************** Label Type = 991 ****************

Label Name = Spclty end prep

with end prep: [2] [4] [6]



1 [2] 3 [4] 5 [6]

- ’with end prep: ’ cp_1_end_prep

- Character (15)


- Character (15)


- Character (15)

***************************************

C - 28


C.3 HITS Report (.h file) __________________________________________________________________________________________________________________________________________________ Date: 30-MAR-1994 02:03:53 Project Database: pd_stdeng_o43 Model Files: skiso3 skiso1 38eqp01 40eqp01


Occ

COMP

16

cp # 0

1369.58

X

421.10

Y

13.46

Z


0

0

Flags 3

Topo 0

Seq Branch Sg_occ 0

0

9

1

COMP

16

1

1369.58

420.95

13.46

0

0

0

3

0

0

0

9

2

COMP

16

2

1369.58

421.24

13.46

0

0

0

3

0

0

0

9

3

COMP

14

0

1363.08

422.45

15.18

0

0

0

3

0

0

0

5

4

COMP

14

1

1363.08

422.45

14.42

0

0

0

3

0

0

0

5

5

COMP

14

2

1363.08

422.45

15.94

0

0

0

3

0

0

0

8

6

COMP

14

3

1362.40

422.45

15.18

0

0

0

3

0

0

0

7

7

COMP

27

0

1362.35

422.45

15.18

0

0

0

3

0

0

0

7

8

COMP

27

1

1362.40

422.45

15.18

0

0

0

3

0

0

0

7

9

COMP

29

0

1369.58

422.45

18.46

0

0

0

3

0

0

0

16

10

COMP

29

1

1370.05

422.45

18.46

0

0

0

3

0

0

0

16

11

COMP

29

2

1369.11

422.45

18.46

0

0

0

3

0

0

0

17

12

COMP

29

3

1369.58

422.45

17.99

0

0

0

3

0

0

0

14

13

COMP

32

0

1373.58

422.45

18.46

0

0

0

3

0

0

0

16

14

COMP

32

1

1373.58

423.20

18.46

0

0

0

3

0

0

0

16

15

COMP

32

2

1372.83

422.45

18.46

0

0

0

3

0

0

0

16

16

COMP

33

0

1373.58

429.80

18.46

0

0

0

3

0

0

0

16

17

COMP

33

1

1372.83

429.80

18.46

0

0

0

3

0

0

0

16

18

COMP

33

2

1373.58

429.05

18.46

0

0

0

3

0

0

0

16

19

COMP

34

0

1364.58

429.80

18.46

0

0

0

3

0

0

0

16

20

COMP

34

1

1364.58

429.80

19.21

0

0

0

3

0

0

0

16

21

COMP

34

2

1365.33

429.80

18.46

0

0

0

3

0

0

0

16

22

COMP

35

0

1364.58

429.80

19.35

0

0

0

3

0

0

0

16

23

COMP

35

1

1364.58

429.80

19.51

0

0

0

3

0

0

0

16

24

COMP

35

2

1364.58

429.80

19.21

0

0

0

3

0

0

0

16

25

PIPE

5

1

1370.05

422.45

18.46

0

0

0

5

0

0

0

16

26

PIPE

5

2

1372.83

422.45

18.46

0

0

0

5

0

0

0

16

27

PIPE

6

1

1373.58

423.20

18.46

0

0

0

5

0

0

0

16

28

PIPE

6

2

1373.58

429.05

18.46

0

0

0

5

0

0

0

16

29

PIPE

7

1

1372.83

429.80

18.46

0

0

0

5

0

0

0

16

30

PIPE

7

2

1365.33

429.80

18.46

0

0

0

5

0

0

0

16

31

COMP

30

0

1363.08

422.45

18.46

0

0

0

3

0

0

0

8

32

COMP

30

1

1363.08

422.45

17.71

0

0

0

3

0

0

0

8

33

COMP

30

2

1363.83

422.45

18.46

0

0

0

3

0

0

0

17

34

PIPE

3

1

1369.11

422.45

18.46

0

0

0

5

0

0

0

17

35

PIPE

3

2

1363.83

422.45

18.46

0

0

0

5

0

0

0

17

36

COMP

17

0

1369.58

421.47

13.41

0

0

0

3

0

0

0

11

37

COMP

17

1

1369.58

421.70

13.37

0

0

0

3

0

0

0

11

38

COMP

17

2

1369.58

421.24

13.46

0

0

0

3

0

0

0

10

39

COMP

17

3T

1369.58

421.47

13.18

0

0

0

3

0

0

0

12

40

COMP

6

0

1363.08

421.10

13.46

0

0

0

3

0

0

0

3

41

COMP

6

1

1363.08

420.95

13.46

0

0

0

3

0

0

0

3

42

COMP

6

2

1363.08

421.24

13.46

0

0

0

3

0

0

0

3

43

COMP

15

0

1363.08

422.45

16.38

0

0

0

3

0

0

0

8

44

COMP

15

1

1363.08

422.45

15.94

0

0

0

3

0

0

0

8

45

COMP

15

2

1363.08

422.45

16.82

0

0

0

3

0

0

0

8

46

COMP

31

0

1363.08

422.45

16.97

0

0

0

3

0

0

0

8

47

COMP

31

1

1363.08

422.45

16.82

0

0

0

3

0

0

0

8

48


COMP

31

2

1363.08

422.45

17.12

0

0

0

3

0

0

0

8

49

PIPE

4

1

1363.08

422.45

17.71

0

0

0

5

0

0

0

8

50

PIPE

4

2

1363.08

422.45

17.12

0

0

0

5

0

0

0

8

51

COMP

7

0

1363.08

421.47

13.41

0

0

0

3

0

0

0

5

52

COMP

7

1

1363.08

421.70

13.37

0

0

0

3

0

0

0

5

53

COMP

7

2

1363.08

421.24

13.46

0

0

0

3

0

0

0

4

54

COMP

7

3T

1363.08

421.47

13.18

0

0

0

3

0

0

0

6

55

COMP

8

0

1363.08

421.47

13.06

0

0

0

3

0

0

0

6

56

COMP

8

1

1363.08

421.47

13.18

0

0

0

3

0

0

0

6

57

COMP

8

2

1363.08

421.47

12.93

0

0

0

3

0

0

0

6

58

COMP

9

0

1363.08

421.47

12.82

0

0

0

3

0

0

0

6

59

COMP

9

1

1363.08

421.47

12.93

0

0

0

3

0

0

0

6

60

COMP

9

2

1363.08

421.47

12.71

0

0

0

3

0

0

0

6

61

COMP

10

0

1363.08

421.47

12.58

0

0

0

3

0

0

0

6

62

COMP

10

1

1363.08

421.47

12.71

0

0

0

3

0

0

0

6

63

COMP

10

2

1363.08

421.47

12.46

0

0

0

3

0

0

0

6

64

COMP

11

0

1363.08

421.47

12.43

0

0

0

3

0

0

0

6

65

COMP

11

1

1363.08

421.47

12.46

0

0

0

3

0

0

0

6

66

COMP

26

0

1364.58

429.80

19.54

0

0

0

3

0

0

0

15

67

COMP

26

1

1364.58

429.80

19.58

0

0

0

3

0

0

0

15

68

COMP

26

2

1364.58

429.80

19.51

0

0

0

3

0

0

0

15

69

COMP

22

0

1369.58

422.45

13.37

0

0

0

3

0

0

0

11

70

COMP

22

1

1369.58

421.70

13.37

0

0

0

3

0

0

0

11

71

COMP

22

2

1369.58

422.45

14.12

0

0

0

3

0

0

0

11

72

COMP

23

0

1369.58

422.45

14.27

0

0

0

3

0

0

0

11

73

COMP

23

1

1369.58

422.45

14.42

0

0

0

3

0

0

0

11

74

COMP

23

2

1369.58

422.45

14.12

0

0

0

3

0

0

0

11

75

COMP

24

0

1369.58

422.45

15.18

0

0

0

3

0

0

0

11

76

COMP

24

1

1369.58

422.45

14.42

0

0

0

3

0

0

0

11

77

COMP

24

2

1369.58

422.45

15.94

0

0

0

3

0

0

0

14

78

COMP

24

3

1368.90

422.45

15.18

0

0

0

3

0

0

0

13

79

SUPP

4

1

1369.58

422.45

13.37

0

0

0

8

0

0

0

11

80

SUPP

4

2

1369.58

422.45

12.30

0

0

0

8

0

0

0

11

81

COMP

12

0

1363.08

422.45

13.37

0

0

0

3

0

0

0

5

82

COMP

12

1

1363.08

421.70

13.37

0

0

0

3

0

0

0

5

83

COMP

12

2

1363.08

422.45

14.12

0

0

0

3

0

0

0

5

84

COMP

13

0

1363.08

422.45

14.27

0

0

0

3

0

0

0

5

85

COMP

13

1

1363.08

422.45

14.42

0

0

0

3

0

0

0

5

86

COMP

13

2

1363.08

422.45

14.12

0

0

0

3

0

0

0

5

87

SUPP

3

1

1363.08

422.45

13.37

0

0

0

8

0

0

0

5

88

SUPP

3

2

1363.08

422.45

12.30

0

0

0

8

0

0

0

5

89

COMP

25

0

1369.58

422.45

16.38

0

0

0

3

0

0

0

14

90

COMP

25

1

1369.58

422.45

15.94

0

0

0

3

0

0

0

14

91

COMP

25

2

1369.58

422.45

16.82

0

0

0

3

0

0

0

14

92

COMP

305

0

1369.58

422.45

16.97

0

0

0

3

0

0

0

14

93

COMP

305

1

1369.58

422.45

16.82

0

0

0

3

0

0

0

14

94

COMP

305

2

1369.58

422.45

17.12

0

0

0

3

0

0

0

14

95

PIPE

103

1

1369.58

422.45

17.12

0

0

0

5

0

0

0

14

96

PIPE

103

2

1369.58

422.45

17.99

0

0

0

5

0

0

0

14

97

COMP

18

0

1369.58

421.47

13.06

0

0

0

3

0

0

0

12

98

COMP

18

1

1369.58

421.47

13.18

0

0

0

3

0

0

0

12

99

COMP

18

2

1369.58

421.47

12.93

0

0

0

3

0

0

0

12

100

COMP

19

0

1369.58

421.47

12.82

0

0

0

3

0

0

0

12

101

COMP

19

1

1369.58

421.47

12.93

0

0

0

3

0

0

0

12

102

COMP

19

2

1369.58

421.47

12.71

0

0

0

3

0

0

0

12

103

COMP

20

0

1369.58

421.47

12.58

0

0

0

3

0

0

0

12

104

COMP

20

1

1369.58

421.47

12.71

0

0

0

3

0

0

0

12

105

COMP

20

2

1369.58

421.47

12.46

0

0

0

3

0

0

0

12

106

COMP

21

0

1369.58

421.47

12.43

0

0

0

3

0

0

0

12

107

COMP

21

1

1369.58

421.47

12.46

0

0

0

3

0

0

0

12

108

COMP

28

0

1368.85

422.45

15.18

0

0

0

3

0

0

0

13

109

COMP

28

1

1368.90

422.45

15.18

0

0

0

3

0

0

0

13

110

C - 30



Occ

COMP

27

0

1362.35

422.45

15.18

-2

3

0

3

0

0

0

7

1

COMP

27

1

1362.40

422.45

15.18

1

3

0

3

0

0

0

7

2

COMP

14

3

1362.40

422.45

15.18

1

3

0

3

0

0

0

7

3

1

1

1363.08

420.70

13.46

-1

11

0

22

0

0

0

3

4

NOZ

cp #

X

Y

Z

Node Direct Section

Flags

Topo

Seq Branch Sg_occ

NOZ

1

2

1363.08

420.95

13.46

40

11

0

22

0

0

0

3

5

COMP

6

1

1363.08

420.95

13.46

40

11

0

3

0

0

0

3

6

COMP

6

0

1363.08

421.10

13.46

0

11

0

3

0

0

0

3

7

COMP

6

2

1363.08

421.24

13.46

2

11

0

3

0

0

0

3

8

COMP

7

2

1363.08

421.24

13.46

2

12

0

3

0

0

0

4

9

COMP

11

0

1363.08

421.47

12.43

-2

13

0

3

0

0

0

6

10

COMP

11

1

1363.08

421.47

12.46

3

13

0

3

0

0

0

6

11

COMP

10

2

1363.08

421.47

12.46

3

13

0

3

0

0

0

6

12

COMP

10

0

1363.08

421.47

12.58

0

13

0

3

0

0

0

6

13

COMP

9

2

1363.08

421.47

12.71

4

13

0

3

0

0

0

6

14

COMP

10

1

1363.08

421.47

12.71

4

13

0

3

0

0

0

6

15

COMP

9

0

1363.08

421.47

12.82

0

13

0

3

0

0

0

6

16

COMP

9

1

1363.08

421.47

12.93

5

13

0

3

0

0

0

6

17

COMP

8

2

1363.08

421.47

12.93

5

13

0

3

0

0

0

6

18

COMP

8

0

1363.08

421.47

13.06

0

13

0

3

0

0

0

6

19

COMP

7

3T

1363.08

421.47

13.18

6

13

0

3

0

0

0

6

20

COMP

8

1

1363.08

421.47

13.18

6

13

0

3

0

0

0

6

21

COMP

7

0

1363.08

421.47

13.41

0

13

0

3

0

0

0

5

22

COMP

12

1

1363.08

421.70

13.37

7

15

0

3

0

0

0

5

23

COMP

7

1

1363.08

421.70

13.37

7

12

0

3

0

0

0

5

24

SUPP

3

2

1363.08

422.45

12.30

-3

2

0

8

0

0

0

5

25

COMP

12

0

1363.08

422.45

13.37

0

15

0

3

0

0

0

5

26

SUPP

3

1

1363.08

422.45

13.37

0

2

0

8

0

0

0

5

27

COMP

13

2

1363.08

422.45

14.12

9

2

0

3

0

0

0

5

28

COMP

12

2

1363.08

422.45

14.12

9

2

0

3

0

0

0

5

29

COMP

13

0

1363.08

422.45

14.27

0

2

0

3

0

0

0

5

30

COMP

13

1

1363.08

422.45

14.42

10

2

0

3

0

0

0

5

31

COMP

14

1

1363.08

422.45

14.42

10

2

0

3

0

0

0

5

32

COMP

14

0

1363.08

422.45

15.18

0

3

0

3

0

0

0

5

33

COMP

15

1

1363.08

422.45

15.94

11

2

0

3

0

0

0

8

34

COMP

14

2

1363.08

422.45

15.94

11

2

0

3

0

0

0

8

35

COMP

15

0

1363.08

422.45

16.38

0

2

0

3

0

0

0

8

36

COMP

31

1

1363.08

422.45

16.82

12

2

0

3

0

0

0

8

37

COMP

15

2

1363.08

422.45

16.82

12

2

0

3

0

0

0

8

38

COMP

31

0

1363.08

422.45

16.97

0

2

0

3

0

0

0

8

39

COMP

31

2

1363.08

422.45

17.12

13

2

0

3

0

0

0

8

40

PIPE

4

2

1363.08

422.45

17.12

13

2

0

5

0

0

0

8

41

COMP

30

1

1363.08

422.45

17.71

14

2

0

3

0

0

0

8

42

PIPE

4

1

1363.08

422.45

17.71

14

2

0

5

0

0

0

8

43

COMP

30

0

1363.08

422.45

18.46

0

4

0

3

0

0

0

8

44

PIPE

3

2

1363.83

422.45

18.46

15

4

0

5

0

0

0

17

45

COMP

30

2

1363.83

422.45

18.46

15

4

0

3

0

0

0

17

46

COMP

34

0

1364.58

429.80

18.46

0

8

0

3

0

0

0

16

47

COMP

35

2

1364.58

429.80

19.21

16

8

0

3

0

0

0

16

48

COMP

34

1

1364.58

429.80

19.21

16

8

0

3

0

0

0

16

49

COMP

35

0

1364.58

429.80

19.35

0

8

0

3

0

0

0

16

50

COMP

35

1

1364.58

429.80

19.51

17

8

0

3

0

0

0

16

51

COMP

26

2

1364.58

429.80

19.51

17

8

0

3

0

0

0

15

52

COMP

26

0

1364.58

429.80

19.54

0

8

0

3

0

0

0

15

53

COMP

26

1

1364.58

429.80

19.58

41

8

0

3

0

0

0

15

54

NOZ

7

2

1364.58

429.80

19.58

41

8

0

22

0

0

0

15

55

NOZ

7

1

1364.58

429.80

20.58

-1

8

0

22

0

0

0

15

56

COMP

34

2

1365.33

429.80

18.46

18

7

0

3

0

0

0

16

57

PIPE

7

2

1365.33

429.80

18.46

18

7

0

5

0

0

0

16

58

COMP

28

0

1368.85

422.45

15.18

-2

3

0

3

0

0

0

13

59

COMP

24

3

1368.90

422.45

15.18

19

3

0

3

0

0

0

13

60

COMP

28

1

1368.90

422.45

15.18

19

3

0

3

0

0

0

13

61

PIPE

3

1

1369.11

422.45

18.46

20

4

0

5

0

0

0

17

62


COMP

29

2

1369.11

422.45

18.46

20

4

0

3

0

0

0

17

63

NOZ

3

1

1369.58

420.70

13.46

-1

1

0

22

0

0

0

9

64

NOZ

3

2

1369.58

420.95

13.46

39

1

0

22

0

0

0

9

65

COMP

16

1

1369.58

420.95

13.46

39

1

0

3

0

0

0

9

66

COMP

16

0

1369.58

421.10

13.46

0

1

0

3

0

0

0

9

67

COMP

16

2

1369.58

421.24

13.46

21

1

0

3

0

0

0

9

68

COMP

17

2

1369.58

421.24

13.46

21

9

0

3

0

0

0

10

69

COMP

21

0

1369.58

421.47

12.43

-2

10

0

3

0

0

0

12

70

COMP

21

1

1369.58

421.47

12.46

22

10

0

3

0

0

0

12

71

COMP

20

2

1369.58

421.47

12.46

22

10

0

3

0

0

0

12

72

COMP

20

0

1369.58

421.47

12.58

0

10

0

3

0

0

0

12

73

COMP

20

1

1369.58

421.47

12.71

23

10

0

3

0

0

0

12

74

COMP

19

2

1369.58

421.47

12.71

23

10

0

3

0

0

0

12

75

COMP

19

0

1369.58

421.47

12.82

0

10

0

3

0

0

0

12

76

COMP

18

2

1369.58

421.47

12.93

24

10

0

3

0

0

0

12

77

COMP

19

1

1369.58

421.47

12.93

24

10

0

3

0

0

0

12

78

COMP

18

0

1369.58

421.47

13.06

0

10

0

3

0

0

0

12

79

COMP

17

3T

1369.58

421.47

13.18

25

10

0

3

0

0

0

12

80

COMP

18

1

1369.58

421.47

13.18

25

10

0

3

0

0

0

12

81

COMP

17

0

1369.58

421.47

13.41

0

10

0

3

0

0

0

11

82

COMP

22

1

1369.58

421.70

13.37

26

14

0

3

0

0

0

11

83

COMP

17

1

1369.58

421.70

13.37

26

9

0

3

0

0

0

11

84

SUPP

4

2

1369.58

422.45

12.30

-3

5

0

8

0

0

0

11

85

COMP

22

0

1369.58

422.45

13.37

0

14

0

3

0

0

0

11

86

SUPP

4

1

1369.58

422.45

13.37

0

5

0

8

0

0

0

11

87

COMP

22

2

1369.58

422.45

14.12

28

5

0

3

0

0

0

11

88

COMP

23

2

1369.58

422.45

14.12

28

5

0

3

0

0

0

11

89

COMP

23

0

1369.58

422.45

14.27

0

5

0

3

0

0

0

11

90

COMP

23

1

1369.58

422.45

14.42

29

5

0

3

0

0

0

11

91

COMP

24

1

1369.58

422.45

14.42

29

5

0

3

0

0

0

11

92

COMP

24

0

1369.58

422.45

15.18

0

5

0

3

0

0

0

11

93

COMP

24

2

1369.58

422.45

15.94

30

5

0

3

0

0

0

14

94

COMP

25

1

1369.58

422.45

15.94

30

5

0

3

0

0

0

14

95

COMP

25

0

1369.58

422.45

16.38

0

5

0

3

0

0

0

14

96

COMP

25

2

1369.58

422.45

16.82

31

5

0

3

0

0

0

14

97

COMP

305

1

1369.58

422.45

16.82

31

5

0

3

0

0

0

14

98

COMP

305

0

1369.58

422.45

16.97

0

5

0

3

0

0

0

14

99

PIPE

103

1

1369.58

422.45

17.12

32

5

0

5

0

0

0

14

100

COMP

305

2

1369.58

422.45

17.12

32

5

0

3

0

0

0

14

101

PIPE

103

2

1369.58

422.45

17.99

33

5

0

5

0

0

0

14

102

COMP

29

3

1369.58

422.45

17.99

33

5

0

3

0

0

0

14

103

COMP

29

0

1369.58

422.45

18.46

0

5

0

3

0

0

0

16

104

COMP

29

1

1370.05

422.45

18.46

34

4

0

3

0

0

0

16

105

PIPE

5

1

1370.05

422.45

18.46

34

4

0

5

0

0

0

16

106

PIPE

5

2

1372.83

422.45

18.46

35

4

0

5

0

0

0

16

107

COMP

32

2

1372.83

422.45

18.46

35

4

0

3

0

0

0

16

108

PIPE

7

1

1372.83

429.80

18.46

36

7

0

5

0

0

0

16

109

COMP

33

1

1372.83

429.80

18.46

36

7

0

3

0

0

0

16

110

COMP

32

0

1373.58

422.45

18.46

0

6

0

3

0

0

0

16

111

COMP

32

1

1373.58

423.20

18.46

37

6

0

3

0

0

0

16

112

PIPE

6

1

1373.58

423.20

18.46

37

6

0

5

0

0

0

16

113

COMP

33

2

1373.58

429.05

18.46

38

6

0

3

0

0

0

16

114

PIPE

6

2

1373.58

429.05

18.46

38

6

0

5

0

0

0

16

115

COMP

33

0

1373.58

429.80

18.46

0

7

0

3

0

0

0

16

116


Cp

5 Next

Action

3

2

Name NOZ

Node 39

Ref Design 112

1

1

1

5 Next

16

1

COMP

39

2

1

1

2

5 Next

16

2

COMP

21

3

1

1

3

5 Next

17

2

COMP

21

39

1

1

4

6 Push

17

3

COMP

25

40

1

0

0

5 Next

17

1

COMP

26

38

1

1

5

5 Next

22

1

COMP

26

71

1

1

6

++++

C - 32


5 Next

22

2

COMP

28

72

1

1

7

5 Next

23

2

COMP

28

75

1

1

8

5 Next

23

1

COMP

29

74

1

1

9

5 Next

24

1

COMP

29

77

1

1

10

6 Push

24

3

COMP

19

79

1

0

0

5 Next

24

2

COMP

30

78

1

1

11

5 Next

25

1

COMP

30

91

1

1

12

5 Next

25

2

COMP

31

92

1

1

13

5 Next

305

1

COMP

31

94

1

1

14

5 Next

305

2

COMP

32

95

1

1

15

5 Next

103

1

PIPE

32

96

1

1

16

5 Next

103

2

PIPE

33

97

1

1

17

5 Next

29

3

COMP

33

13

1

1

18

6 Push

29

2

COMP

20

12

1

0

0

5 Next

29

1

COMP

34

11

1

2

1

5 Next

5

1

PIPE

34

26

1

2

2

5 Next

5

2

PIPE

35

27

1

2

3

5 Next

32

2

COMP

35

16

1

2

4

5 Next

32

1

COMP

37

15

1

2

5

5 Next

6

1

PIPE

37

28

1

2

6

5 Next

6

2

PIPE

38

29

1

2

7

5 Next

33

2

COMP

38

19

1

2

8

5 Next

33

1

COMP

36

18

1

2

9

5 Next

7

1

PIPE

36

30

1

2

10

++++

++++

5 Next

7

2

PIPE

18

31

1

2

11

5 Next

34

2

COMP

18

22

1

2

12

5 Next

34

1

COMP

16

21

1

2

13

5 Next

35

2

COMP

16

25

1

2

14

5 Next

35

1

COMP

17

24

1

2

15

5 Next

26

2

COMP

17

69

1

2

16

5 Next

26

1

COMP

41

68

1

2

17

5 Next

7

2

NOZ

41

116

1

2

18

5 Next

7

1

NOZ

-1

115

1

2

7 Pull

29

2

COMP

20

12

1

5 Next

29

2

COMP

20

12

1

2

-1

5 Next

3

1

PIPE

20

35

1

2

-2

5 Next

3

2

PIPE

15

36

1

2

-3

5 Next

30

2

COMP

15

34

1

2

-4

5 Next

30

1

COMP

14

33

1

2

-5

5 Next

4

1

PIPE

14

50

1

2

-6

5 Next

4

2

PIPE

13

51

1

2

-7

5 Next

31

2

COMP

13

49

1

2

-8

5 Next

31

1

COMP

12

48

1

2

-9

5 Next

15

2

COMP

12

46

1

2

-10

5 Next

15

1

COMP

11

45

1

2

-11

5 Next

14

2

COMP

11

6

1

2

-12

6 Push

14

3

COMP

1

7

1

5 Next

14

1

COMP

10

5

5 Next

13

1

COMP

10

5 Next

13

2

COMP

9

5 Next

12

2

COMP

5 Next

12

1

5 Next

7

6 Push

—-

2

++++

19 0

0

0

1

2

-13

86

1

2

-14

87

1

2

-15

9

84

1

2

-16

COMP

7

83

1

2

-17

1

COMP

7

53

1

2

-18

7

3

COMP

6

55

1

5 Next

7

2

COMP

2

54

5 Next

6

2

COMP

2

5 Next

6

1

COMP

40

5 Next

1

2

NOZ

5 Next

1

1

7 Pull

7

5 Next

++++

0

0

1

2

-19

43

1

2

-20

42

1

2

-21

40

114

1

2

-22

NOZ

-1

113

1

2

-23

3

COMP

6

55

1

7

3

COMP

6

55

1

3

1

5 Next

8

1

COMP

6

57

1

3

2

5 Next

8

2

COMP

5

58

1

3

3

5 Next

9

1

COMP

5

60

1

3

4

5 Next

9

2

COMP

4

61

1

3

5

—-

0

0


5 Next

10

1

COMP

4

63

1

3

6

5 Next

10

2

COMP

3

64

1

3

7

5 Next

11

1

COMP

3

66

1

3

8

5 Next

11

0

COMP

-2

65

1

3

7 Pull

14

3

COMP

1

7

1

5 Next

14

3

COMP

1

7

1

4

1

5 Next

27

1

COMP

1

9

1

4

2

5 Next

27

0

COMP

-2

8

1

4

7 Pull

24

3

COMP

19

79

1

5 Next

24

3

COMP

19

79

1

5

1

5 Next

28

1

COMP

19

110

1

5

2

5 Next

28

0

COMP

-2

109

1

5

7 Pull

17

3

COMP

25

40

1

5 Next

17

3

COMP

25

40

1

6

1

5 Next

18

1

COMP

25

99

1

6

2

5 Next

18

2

COMP

24

100

1

6

3

5 Next

19

1

COMP

24

102

1

6

4

5 Next

19

2

COMP

23

103

1

6

5

5 Next

20

1

COMP

23

105

1

6

6

5 Next

20

2

COMP

22

106

1

6

7

5 Next

21

1

COMP

22

108

1

6

8

5 Next

21

0

COMP

-2

107

1

6

-1

39

21

26

28

29

30

31

32

33

34

35

37

38

36

18

16

17

41

20

15

14

13

12

11

10

9

7

2

40

6

5

4

3

1

19

25

24

23

22

—-

—-

—-

0

9 0

0

3 0

0

3 0

9

0 # Sections: 1


Occ

COMP

16

cp # 0

1369.58

X

421.10

Y

13.46

Z


1

0

Flags 3

Topo 0

Seq Branch Sg_occ 0

0

9

1

COMP

9

0

1363.08

421.47

12.82

0

13

0

3

0

0

0

6

2

COMP

30

0

1363.08

422.45

18.46

0

4

0

3

0

0

0

8

3

COMP

14

0

1363.08

422.45

15.18

0

3

0

3

0

0

0

5

4

COMP

10

0

1363.08

421.47

12.58

0

13

0

3

0

0

0

6

5

COMP

305

0

1369.58

422.45

16.97

0

5

0

3

0

0

0

14

6

COMP

32

0

1373.58

422.45

18.46

0

6

0

3

0

0

0

16

7

COMP

17

0

1369.58

421.47

13.41

0

10

0

3

0

0

0

11

8

COMP

26

0

1364.58

429.80

19.54

0

8

0

3

0

0

0

15

9

COMP

29

0

1369.58

422.45

18.46

0

5

0

3

0

0

0

16

10

COMP

18

0

1369.58

421.47

13.06

0

10

0

3

0

0

0

12

11

COMP

22

0

1369.58

422.45

13.37

0

14

0

3

0

0

0

11

12

COMP

13

0

1363.08

422.45

14.27

0

2

0

3

0

0

0

5

13

COMP

8

0

1363.08

421.47

13.06

0

13

0

3

0

0

0

6

14

COMP

23

0

1369.58

422.45

14.27

0

5

0

3

0

0

0

11

15

COMP

15

0

1363.08

422.45

16.38

0

2

0

3

0

0

0

8

16

COMP

33

0

1373.58

429.80

18.46

0

7

0

3

0

0

0

16

17

COMP

24

0

1369.58

422.45

15.18

0

5

0

3

0

0

0

11

18

COMP

31

0

1363.08

422.45

16.97

0

2

0

3

0

0

0

8

19

COMP

34

0

1364.58

429.80

18.46

0

8

0

3

0

0

0

16

20

COMP

12

0

1363.08

422.45

13.37

0

15

0

3

0

0

0

5

21

COMP

19

0

1369.58

421.47

12.82

0

10

0

3

0

0

0

12

22

COMP

35

0

1364.58

429.80

19.35

0

8

0

3

0

0

0

16

23

COMP

6

0

1363.08

421.10

13.46

0

11

0

3

0

0

0

3

24

COMP

25

0

1369.58

422.45

16.38

0

5

0

3

0

0

0

14

25

COMP

20

0

1369.58

421.47

12.58

0

10

0

3

0

0

0

12

26

COMP

7

0

1363.08

421.47

13.41

0

13

0

3

0

0

0

5

27

SUPP

4

1

1369.58

422.45

13.37

0

5

0

8

0

0

0

11

28

SUPP

3

1

1363.08

422.45

13.37

0

2

0

8

0

0

0

5

29

SUPP

3

2

1363.08

422.45

12.30

-3

2

0

8

0

0

0

5

30

SUPP

4

2

1369.58

422.45

12.30

-3

5

0

8

0

0

0

11

31

C - 34


NOZ

3

1

1369.58

420.70

13.46

-1

1

1

22

1

0

0

9

32

NOZ

3

2

1369.58

420.95

13.46

39

1

1

22

1

1

0

9

33

COMP

16

1

1369.58

420.95

13.46

39

1

1

3

1

2

0

9

34

COMP

16

2

1369.58

421.24

13.46

21

1

1

3

1

3

0

9

35

COMP

17

2

1369.58

421.24

13.46

21

9

1

3

1

4

108

10

36

COMP

17

1

1369.58

421.70

13.37

26

9

1

3

1

5

108

11

37

COMP

22

1

1369.58

421.70

13.37

26

14

1

3

1

6

0

11

38

COMP

22

2

1369.58

422.45

14.12

28

5

1

3

1

7

0

11

39

COMP

23

2

1369.58

422.45

14.12

28

5

1

3

1

8

0

11

40

COMP

23

1

1369.58

422.45

14.42

29

5

1

3

1

9

0

11

41

COMP

24

1

1369.58

422.45

14.42

29

5

1

3

1

10

105

11

42

COMP

24

2

1369.58

422.45

15.94

30

5

1

3

1

11

105

14

43

COMP

25

1

1369.58

422.45

15.94

30

5

1

3

1

12

0

14

44

COMP

25

2

1369.58

422.45

16.82

31

5

1

3

1

13

0

14

45

COMP

305

1

1369.58

422.45

16.82

31

5

1

3

1

14

0

14

46

COMP

305

2

1369.58

422.45

17.12

32

5

1

3

1

15

0

14

47

PIPE

103

1

1369.58

422.45

17.12

32

5

1

5

1

16

0

14

48

PIPE

103

2

1369.58

422.45

17.99

33

5

1

5

1

17

0

14

49

COMP

29

3

1369.58

422.45

17.99

33

5

1

3

1

18

-73

14

50

NOZ

1

1

1363.08

420.70

13.46

-1

11

1

22

2

-23

0

3

51

NOZ

1

2

1363.08

420.95

13.46

40

11

1

22

2

-22

0

3

52

COMP

6

1

1363.08

420.95

13.46

40

11

1

3

2

-21

0

3

53

COMP

6

2

1363.08

421.24

13.46

2

11

1

3

2

-20

0

3

54

COMP

7

2

1363.08

421.24

13.46

2

12

1

3

2

-19

93

4

55

COMP

7

1

1363.08

421.70

13.37

7

12

1

3

2

-18

93

5

56

COMP

12

1

1363.08

421.70

13.37

7

15

1

3

2

-17

0

5

57

COMP

12

2

1363.08

422.45

14.12

9

2

1

3

2

-16

0

5

58

COMP

13

2

1363.08

422.45

14.12

9

2

1

3

2

-15

0

5

59

COMP

13

1

1363.08

422.45

14.42

10

2

1

3

2

-14

0

5

60

COMP

14

1

1363.08

422.45

14.42

10

2

1

3

2

-13

102

5

61

COMP

14

2

1363.08

422.45

15.94

11

2

1

3

2

-12

102

8

62

COMP

15

1

1363.08

422.45

15.94

11

2

1

3

2

-11

0

8

63

COMP

15

2

1363.08

422.45

16.82

12

2

1

3

2

-10

0

8

64

COMP

31

1

1363.08

422.45

16.82

12

2

1

3

2

-9

0

8

65

COMP

31

2

1363.08

422.45

17.12

13

2

1

3

2

-8

0

8

66

PIPE

4

2

1363.08

422.45

17.12

13

2

1

5

2

-7

0

8

67

PIPE

4

1

1363.08

422.45

17.71

14

2

1

5

2

-6

0

8

68

COMP

30

1

1363.08

422.45

17.71

14

2

1

3

2

-5

0

8

69

COMP

30

2

1363.83

422.45

18.46

15

4

1

3

2

-4

0

17

70

PIPE

3

2

1363.83

422.45

18.46

15

4

1

5

2

-3

0

17

71

PIPE

3

1

1369.11

422.45

18.46

20

4

1

5

2

-2

0

17

72

COMP

29

2

1369.11

422.45

18.46

20

4

1

3

2

-1

50

17

73

COMP

29

1

1370.05

422.45

18.46

34

4

1

3

2

1

50

16

74

PIPE

5

1

1370.05

422.45

18.46

34

4

1

5

2

2

0

16

75

PIPE

5

2

1372.83

422.45

18.46

35

4

1

5

2

3

0

16

76

COMP

32

2

1372.83

422.45

18.46

35

4

1

3

2

4

0

16

77

COMP

32

1

1373.58

423.20

18.46

37

6

1

3

2

5

0

16

78

PIPE

6

1

1373.58

423.20

18.46

37

6

1

5

2

6

0

16

79

PIPE

6

2

1373.58

429.05

18.46

38

6

1

5

2

7

0

16

80

COMP

33

2

1373.58

429.05

18.46

38

6

1

3

2

8

0

16

81

COMP

33

1

1372.83

429.80

18.46

36

7

1

3

2

9

0

16

82

PIPE

7

1

1372.83

429.80

18.46

36

7

1

5

2

10

0

16

83

PIPE

7

2

1365.33

429.80

18.46

18

7

1

5

2

11

0

16

84

COMP

34

2

1365.33

429.80

18.46

18

7

1

3

2

12

0

16

85

COMP

34

1

1364.58

429.80

19.21

16

8

1

3

2

13

0

16

86

COMP

35

2

1364.58

429.80

19.21

16

8

1

3

2

14

0

16

87

COMP

35

1

1364.58

429.80

19.51

17

8

1

3

2

15

0

16

88

COMP

26

2

1364.58

429.80

19.51

17

8

1

3

2

16

0

15

89

COMP

26

1

1364.58

429.80

19.58

41

8

1

3

2

17

0

15

90

NOZ

7

2

1364.58

429.80

19.58

41

8

1

22

2

18

0

15

91

NOZ

7

1

1364.58

429.80

20.58

-1

8

1

22

2

19

0

15

92


COMP

7

3T

1363.08

421.47

13.18

6

13

1

3

3

1

-55

6

93

COMP

8

1

1363.08

421.47

13.18

6

13

1

3

3

2

0

6

94

COMP

8

2

1363.08

421.47

12.93

5

13

1

3

3

3

0

6

95

COMP

9

1

1363.08

421.47

12.93

5

13

1

3

3

4

0

6

96

COMP

9

2

1363.08

421.47

12.71

4

13

1

3

3

5

0

6

97

COMP

10

1

1363.08

421.47

12.71

4

13

1

3

3

6

0

6

98

COMP

10

2

1363.08

421.47

12.46

3

13

1

3

3

7

0

6

99

COMP

11

1

1363.08

421.47

12.46

3

13

1

3

3

8

0

6

100

COMP

11

0

1363.08

421.47

12.43

-2

13

1

3

3

9

0

6

101

COMP

14

3

1362.40

422.45

15.18

1

3

1

3

4

1

-61

7

102

COMP

27

1

1362.40

422.45

15.18

1

3

1

3

4

2

0

7

103

COMP

27

0

1362.35

422.45

15.18

-2

3

1

3

4

3

0

7

104

COMP

24

3

1368.90

422.45

15.18

19

3

1

3

5

1

-42

13

105

COMP

28

1

1368.90

422.45

15.18

19

3

1

3

5

2

0

13

106

COMP

28

0

1368.85

422.45

15.18

-2

3

1

3

5

3

0

13

107

COMP

17

3T

1369.58

421.47

13.18

25

10

1

3

6

1

-36

12

108

COMP

18

1

1369.58

421.47

13.18

25

10

1

3

6

2

0

12

109

COMP

18

2

1369.58

421.47

12.93

24

10

1

3

6

3

0

12

110

COMP

19

1

1369.58

421.47

12.93

24

10

1

3

6

4

0

12

111

COMP

19

2

1369.58

421.47

12.71

23

10

1

3

6

5

0

12

112

COMP

20

1

1369.58

421.47

12.71

23

10

1

3

6

6

0

12

113

COMP

20

2

1369.58

421.47

12.46

22

10

1

3

6

7

0

12

114

COMP

21

1

1369.58

421.47

12.46

22

10

1

3

6

8

0

12

115

COMP

21

0

1369.58

421.47

12.43

-2

10

1

3

6

9

0

12

116


X

Y

Z

X

Y

Z

Occ

NOZ

33274000

10480294

501904

33274000

10480294

477520

7

in_cp Out_cp Leg Dn_occ Sg_occ 1

2

in

26

15

BLSP

33274000

10480294

477393

33274000

10480294

475615

26

1

2

in

35

15

FWN

33274000

10480294

475615

33274000

10480294

468376

35

1

2

in

34

16

E90L

33274000

10480294

468376

33274000

10480294

450088

34

1

0

in

0

16

E90L

33274000

10480294

450088

33292288

10480294

450088

34

0

2

ou

7

16

PIPE

33292288

10480294

450088

33475168

10480294

450088

7

2

1

in

33

16

E90L

33475168

10480294

450088

33493456

10480294

450088

33

1

0

in

0

16

E90L

33493456

10480294

450088

33493456

10462006

450088

33

0

2

ou

6

16

PIPE

33493456

10462006

450088

33493456

10319258

450088

6

2

1

in

32

16

E90L

33493456

10319258

450088

33493456

10300970

450088

32

1

0

in

0

16

E90L

33493456

10300970

450088

33475168

10300970

450088

32

0

2

ou

5

16

PIPE

33475168

10300970

450088

33407350

10300970

450088

5

2

1

in

29

16

T

33407350

10300970

450088

33395920

10300970

450088

29

1

0

in

0

16

T

33395920

10300970

450088

33395920

10300970

438658

29

0

3

b1

103

14

PIPE

33395920

10300970

438658

33395920

10300970

417449

103

2

1

in

305

14

FWN

33395920

10300970

417449

33395920

10300970

410210

305

2

1

in

25

14

GAT

33395920

10300970

410210

33395920

10300970

388620

25

2

1

in

24

14

STRT

33395920

10300970

388620

33395920

10300970

370078

24

2

0

in

0

14

STRT

33395920

10300970

370078

33379283

10300970

370078

24

0

3

b1

28

13

FBLD

33379283

10300970

370078

33378140

10300970

370078

28

1

0

in

0

13

STRT

33395920

10300970

370078

33395920

10300970

351536

24

0

1

ou

23

11

FWN

33395920

10300970

351536

33395920

10300970

344297

23

1

2

in

22

11

E90L

33395920

10300970

344297

33395920

10300970

326009

22

2

0

in

0

11

PSP2

33395920

10300970

326009

33395920

10300970

299847

4

1

2

in

0

11

E90L

33395920

10300970

326009

33395920

10282682

326009

22

0

1

ou

17

11

REDE

33395920

10282682

326009

33395920

10271506

328168

17

1

2

in

16

11

REDE

33395920

10277094

327089

33395920

10277094

321501

17

0

3

ta

18

12

NIP

33395920

10277094

321501

33395920

10277094

315405

18

1

2

in

19

12

GATR

33395920

10277094

315405

33395920

10277094

309817

19

1

2

in

20

12

NIP

33395920

10277094

309817

33395920

10277094

303721

20

1

2

in

21

12

CAPO

33395920

10277094

303721

33395920

10277094

303213

21

1

0

in

0

12

FWN

33395920

10271506

328168

33395920

10264521

328168

16

2

1

in

3

9

NOZ

33395920

10264394

328168

33395920

10258298

328168

3

2

1

in

0

9

T

33395920

10300970

450088

33384490

10300970

450088

29

0

2

ou

3

17

Dash

End

End

End

Dash

C - 36


PIPE

33384490

10300970

450088

33255712

10300970

450088

3

1

2

in

30

17

E90L

33255712

10300970

450088

33237424

10300970

450088

30

2

0

in

0

17

E90L

33237424

10300970

450088

33237424

10300970

431800

30

0

1

ou

4

8

PIPE

33237424

10300970

431800

33237424

10300970

417449

4

1

2

in

31

8

FWN

33237424

10300970

417449

33237424

10300970

410210

31

2

1

in

15

8

GAT

33237424

10300970

410210

33237424

10300970

388620

15

2

1

in

14

8

STRT

33237424

10300970

388620

33237424

10300970

370078

14

2

0

in

0

8

STRT

33237424

10300970

370078

33220787

10300970

370078

14

0

3

b1

27

7

FBLD

33220787

10300970

370078

33219644

10300970

370078

27

1

0

in

0

7

STRT

33237424

10300970

370078

33237424

10300970

351536

14

0

1

ou

13

5

FWN

33237424

10300970

351536

33237424

10300970

344297

13

1

2

in

12

5

E90L

33237424

10300970

344297

33237424

10300970

326009

12

2

0

in

0

5

PSP2

33237424

10300970

326009

33237424

10300970

299847

3

1

2

in

0

5

E90L

33237424

10300970

326009

33237424

10282682

326009

12

0

1

ou

7

5

REDE

33237424

10282682

326009

33237424

10271506

328168

7

1

2

in

6

5

REDE

33237424

10277094

327089

33237424

10277094

321501

7

0

3

ta

8

6

NIP

33237424

10277094

321501

33237424

10277094

315405

8

1

2

in

9

6

GATR

33237424

10277094

315405

33237424

10277094

309817

9

1

2

in

10

6

NIP

33237424

10277094

309817

33237424

10277094

303721

10

1

2

in

11

6

CAPO

33237424

10277094

303721

33237424

10277094

303213

11

1

0

in

0

6

FWN

33237424

10271506

328168

33237424

10264521

328168

6

2

1

in

1

3

NOZ

33237424

10264394

328168

33237424

10258298

328168

1

2

1

in

0

3

End

End

End

Dash


C.4 Intermediate Data File (.idf file) __________________________________________________________________________________________________________________________________________________ 3275

0

1

1

1000

3

0

10

100

28

15

15

457

610

1

1

4

1

0

0

300

0

1

0

1

10

105

0

0

100

0

100

46

1

0

100

0

0

1

3

!

0

1

1

1

1

1

1

1

1

0

0

0

0

0

!

0

0

1

1

1

2

62

1

11

0

0

0

0

0

!

0

0

0

0

0

0

0

0

0

0

0

0

0

0

!

0

0

0

0

0

0

0

0

0

0

0

0

0

0

!

0

0

0

0

0

0

0

0

0

0

0

0

1

0

!

0

1

0

250

0

0

0

70

1

0

5

0

0

0

!

0

0

0

0

0

0

0

0

0

0

0

0

0

0

!

-102

/380311w.i*

-103

//usr/ip32/pd

-1

iso/dat/symbo

-1

275

6 !

l.lib

-104

/380311w.bom

-105

/pdsidf.err

-108

/380311w.prt

-115

/380311w.sht

-122

//usr/ip32/pd

-1

iso/examples/

-1

user.mld

3

-6

25

5

1

0

0

0

0

0

0

0

0

0

3

-25

0

0

0

0

0

0

0

0

0

0

0

0

3

-41

0

0

0

0

0

0

0

0

0

0

0

0

3

-42

0

0

0

0

0

0

0

0

0

0

0

0

3

-43

0

0

0

0

0

0

0

0

0

0

0

0

3

-44

0

0

0

0

0

0

0

0

0

0

0

0

3

-45

0

0

0

0

0

0

0

0

0

0

0

0

3

-700

38000

43390

0

0

0

0

0

0

0

0

0

0

3

-702

0

0

0

0

0

0

0

0

0

0

0

0

-703

0

0

0

0

0

0

0

0

0

0

0

0

3 -207

NPD

-208

CONN TO

-209

SEE ISO

-213

STEM

-215 -217 -218 -219 -220 -221

FW

-222

SLOPE

-243

FLAT SIDE

-244

U

-245

D

-246

N

-247

S

-248

E

-249

W

-250 -253 -255

SHT

-270 -271 -272 -276 -277 -278

SEE SHT

C - 38


-282 -284 -287

ORIENT

-288

LINE :

-289

CLASS:

-290

INSUL:

-291

TRACE:

-292

COAT :

-293

PKGNO:

-294

SCH

-295

CLEAN:

-296

TEST :

-297

STAT :

:

-298 -300 -1

SHOP MATERIAL S

-303

DESCRIPTION

-304

NPD

-305

CMDTY CODE

-307

PIPE

-308

FITTINGS

-309

FLANGES

-310

OTHER THAN SH

-1

OP MATERIALS

-311

GASKET

-312

BOLTS

-313

VALVES/IN-LIN

-1

E ITEMS

-314

INSTRUMENTS

-315

PIPE SUPPORTS

-316

PIECE MARKS

-317 -318 -330

INS

-339

MISCELLANEOUS

-359

DIA X LENGTH

-375

WELDS

-376

FABRICATION M

-1

ATL

-377

ERECTION MATL

-378

OFFSHORE MATL

-330

IN

-400 -401 -402 -403 -404 -405 -406 -407 -410 -411 -6 -7

380311-W380311-W-

-11

2C0032

-14

01/08/94

-15

HF 2 "

-16

HT

-17

NONE

-41

UNDEFINED

-42

PER SPEC

-43

UNDEFINED

0

-44

0 PSIG

-45

UNDEFINED

-131

SHOP-


-132

FLD-

-133

OFFSHR-

-31 -1

38E-104/ N2$4 IN RFFE 300

110

39911971

11626849

835818

39911971

11626849

836135

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

105

39911971

11626849

836135

39911971

11626849

844708

64

3,

0,

10000,FLWN,

0

3001

-39

3

11626849

844708

39911971

11626849

859948

64

4,

0,

10000,ELBW,

9000

3011

11626849

859948

39896731

11626849

859948

64

0,

0,

10000,ELBW,

9000

3011

0,FLOW,

0

0

0

3001

-1

115

-1 -1 -37 -1 -67

8 55

8 W380311-4IN-2 C0032-HF *UNDEFINED*

35

39911971

-39 -1

3 157

-1 -1

8

36 -67

8 56

39911971 *UNDEFINED*

149

39886651

11626849

859948

0

0

0

64

0,

0,

100

39896731

11626849

859948

39876570

11626849

859948

64

5,

0,

10000,

10000,TEBW,

-39

5

-1

35

-1 -1 -67

8 56

8 *UNDEFINED*

45

39876570

11626849

859948

39866093

11626849

859948

64

6,

0,

0

0

0

0

0

0

0

64

0,

0,

39866093

11626849

859948

39866093

11626849

870426

64

0,

0,

-39 -1

155

3011

0

0

10000,TEBW,

0

3011

0,FLOW,

8 56

8

46 -67

0

,

0,

3

-1 -1

,

*UNDEFINED*

149

39866093

11626849

895270

0

0

0

64

0,

0,

0

0

100

39866093

11626849

870426

39866093

11626849

920114

64

5,

0,

10000,

,

0

3001

11626849

920114

39866093

11626849

935354

64

4,

0,

10000,ELBW,

9000

3011

11626849

935354

39866093

11642089

935354

64

0,

0,

10000,ELBW,

9000

3011

11642089

935354

39866093

11759247

935354

64

5,

0,

10000,

,

0

3001

11759247

935354

39866093

11774487

935354

64

4,

0,

10000,ELBW,

9000

3001

11774487

935354

39866093

11774487

920114

64

0,

0,

10000,ELBW,

9000

3001

11774487

920114

39866093

11774487

496569

64

5,

0,

10000,

0

3001

-39

5

-1

33

-1 -1 -67

8 57

8 *UNDEFINED*

35

39866093

-39

3

-1

154

-1 -1

8

36 -67

8 57


100

39866093

-39

5

-1

32

-1 -1 -67

8 57

8 *UNDEFINED*

35

39866093

-39

3

-1

153

-1 -1 36 -67

8 57

8 39866093 *UNDEFINED*

100

39866093

-39

5

,

C - 40

-1


31

-1 -1 -67

8 57

8 *UNDEFINED*

105

39866093

-39

3

-1

152

-1 -1

11774487

496569

39866093

11774487

487996

64

3,

0,

10000,FLWN,

0

3001

8 57

8

110

39866093

11774487

487996

39866093

11774487

487679

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

130

39866093

11774487

487679

39866093

11774487

457199

64

7,

0,

10000,VVFL,

0

3102

-39

3

-1

116

-1 -1

8 57

8

110

39866093

11774487

457199

39866093

11774487

456882

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

105

39866093

11774487

456882

39866093

11774487

448309

64

3,

0,

10000,FLWN,

0

3001

-39

3

11774487

448309

39866093

11774487

391477

64

5,

0,

10000,

0

3001

10000,TEBW,

-1

151

-1 -1 -67

8 57

8 *UNDEFINED*

100

39866093

-39

5

-1

30

-1 -1 -67

8 57

8 *UNDEFINED*

45

39866093

11774487

391477

39866093

11774487

380999

64

6,

0,

0

0

0

0

0

0

0

64

0,

0,

39866093

11774487

380999

39876570

11774487

380999

64

0,

0,

-39 -1

150

3001

0

0

10000,TEBW,

0

3001

0,FLOW,

0

0

0

3001

8 57

8

46 -67

0

,

0,

3

-1 -1

,

*UNDEFINED*

149

39881332

11774487

380999

0

0

0

64

0,

0,

100

39876570

11774487

380999

39886095

11774487

380999

64

5,

0,

10000,

10000,TEBW,

-39

5

-1

29

-1 -1 -67

,

8 59

8 *UNDEFINED*

45

39886095

11774487

380999

39896573

11774487

380999

64

6,

0,

0

3001

0

0

0

0

0

0

0

64

0,

0,

0,

,

0

0

11774487

380999

0

0

0

64

8,

0,

10000,

,

0

602

11774487

380999

39896573

11774487

391477

64

0,

0,

10000,TEBW,

0

3001

11774487

391477

39896573

11774487

400049

64

3,

0,

10000,FLWN,

0

3001

11774487

400049

39896573

11774487

400366

64

1,

0,

10000,

0

2

-39 -1

3 119

-1 -1

8

150 -22

8 59

39896573 PS-0311-1

-39

8

-1

7

-1 -1

8

46 -67

8 59


105

39896573

-39

3

-1

124

-1 -1 110

8 60

8 39896573

,


115

0

0

0

0

0

0

12

2,

0,

,

0

2

130

39896573

11774487

400366

39896573

11774487

430847

64

7,

0,

10000,VVFL,

0

3102

-39 -1

3 125

-1 -1

8,

8 60

8

110

39896573

11774487

430847

39896573

11774487

431164

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

105

39896573

11774487

431164

39896573

11774487

439737

64

3,

0,

10000,FLWN,

0

3001

-39

3

0,FLOW,

-1

149

-1 -1 -67

8 60

8 *UNDEFINED*

149

39896573

11774487

519905

0

0

0

64

0,

0,

0

0

100

39896573

11774487

439737

39896573

11774487

600074

64

5,

0,

10000,

,

0

3001

11774487

600074

39896573

11774487

615314

64

4,

0,

10000,ELBW,

9000

3011

11774487

615314

39896573

11789727

615314

64

0,

0,

10000,ELBW,

9000

3011

11789727

615314

39896574

12194858

615314

64

5,

0,

10000,

,

0

3001

12194858

615314

39896573

12201207

615314

64

9,

0,

10000,ELBW,

4500

3011

12201207

615314

39892083

12205697

615314

64

0,

0,

10000,ELBW,

4500

3011

12205697

615314

39876869

12220909

615314

64

5,

0,

10000,

,

0

3001

12220909

615314

39866093

12231687

615314

64

4,

0,

10000,ELBW,

9000

3011

12231687

615314

39866093

12231687

600074

64

0,

0,

10000,ELBW,

9000

3011

12231687

600074

39866093

12231687

518159

64

5,

0,

10000,

0

3001

-39

5

-1

28

-1 -1 -67

8 60

8 *UNDEFINED*

35

39896573

-39

3

-1

148

-1 -1

8

36 -67

8 60


100

39896573

-39

5

-1

27

-1 -1 -67

8 60

8 *UNDEFINED*

35

39896574

-39

3

-1

147

-1 -1

8

36 -67

8 60


100

39892083

-39

5

-1

26

-1 -1 -67

8 60

8 *UNDEFINED*

35

39876869

-39

3

-1

146

-1 -1

8

36 -67

8 60


100

39866093

-39

5

-1

25

-1 -1 -67

,

8 60

8 *UNDEFINED*

40

39866093

12231687

518159

39866093

12231687

518159

64

5,

0,

10000,

,

0

3001

0

0

0

0

0

0

0

64

0,

0,

0,

,

0

0

-39 -1 -1

3 126

8 60

C - 42

-1

8

41 -67


39866093

12231687

518159

39876250

12231687

518159

48

10,

0,

10000,WTBW,

0

0,FLOW,

3001

*UNDEFINED*

149

39893239

12231687

518159

0

0

0

48

0,

0,

0

0

100

39876250

12231687

518159

39910228

12231687

518159

48

5,

0,

10000,

,

0

3001

12231687

518159

39918165

12231687

518159

48

3,

0,

10000,FLWN,

0

3001

-39

5

-1

36

-1 -1 -67

8 71

8 *UNDEFINED*

105

39910228

-39

3

-1

158

-1 -1

8 71

8

110

39918165

12231687

518159

39918482

12231687

518159

48

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

11,

0,

8,

,

0

2

130

39918482

12231687

518159

39946740

12231687

518159

48

7,

0,

10000,VVFL,

0

3202

-39

3

-1

142

-1 -1

8 71

8

110

39946740

12231687

518159

39947057

12231687

518159

48

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

11,

0,

8,

,

0

2

105

39947057

12231687

518159

39954995

12231687

518159

48

3,

0,

10000,FLWN,

0

3001

-39

3

10000,

,

0

3001

0,FLOW,

0

0

-1

141

-1 -1

8 71

8

42

39866093

12231687

518159

39866093

12231687

518159

64

5,

0,

149

39866093

12231687

481329

0

0

0

64

0,

0,

100

39866093

12231687

518159

39866093

12231687

444499

64

5,

0,

10000,

,

0

3001

12231687

444499

39866093

12231687

435926

64

3,

0,

10000,FLWN,

0

3001

-39

5

-1

25

-1 -1 -67

8 65

8 *UNDEFINED*

105

39866093

-39

3

-1

145

-1 -1

8 65

8

110

39866093

12231687

435926

39866093

12231687

435609

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

130

39866093

12231687

435609

39866093

12231687

405129

64

7,

0,

10000,VVFL,

0

3202

-39

3

-1

140

-1 -1

8 65

8

110

39866093

12231687

405129

39866093

12231687

404812

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

105

39866093

12231687

404812

39866093

12231687

396239

64

3,

0,

10000,FLWN,

0

3001

-39

3

12231687

396239

39866093

12231687

380999

64

4,

0,

10000,ELBW,

9000

3011

12231687

380999

0

0

0

64

12,

0,

10000,

0

602

-1

139

-1 -1 -67

8 65

8 *UNDEFINED*

35

39866093

-39

3

-1

127

-1 -1 150 -22 -39

8 65

8 39866093 PS-0311-2 8

,


-1

8

-1 -1

8

36 -67

8 65

39866093

12231687

380999

39881333

12231687

380999

64

0,

0,

10000,ELBW,

10000,REBW,

55

39881333

12231687

380999

39891493

12231687

379729

64

13,

0,

0

0

0

0

0

0

0

48

0,

0,

105

39891493

12231687

379729

39899430

12231687

379729

48

3,

-39

3

-39 -1

-1

-1

128

0

3601

,

0

0

0,

10000,FLWN,

0

3001

0,

8 65

8 *UNDEFINED*

129

-1 -1

3011

3

-1

-67

9000

*UNDEFINED*

8 66

8

110

39899430

12231687

379729

39899747

12231687

379729

48

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

11,

0,

8,

,

0

2

39899747

12231687

379729

39915623

12231687

379729

48

14,

0,

10000,CVFL,

0

3502

3502

90 -22

38LV$559

-39

6

-1

4

-1 -1

8 66

8

93

39915623

12231687

379729

39931497

12231687

379729

48

0,

0,

10000,CVFL,

0

110

39931497

12231687

379729

39931814

12231687

379729

48

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

11,

0,

8,

,

0

2

105

39931814

12231687

379729

39939753

12231687

379729

48

3,

0,

10000,FLWN,

0

3001

-39

3

10000,REBW,

-1

130

-1 -1 -67

8 66

8 *UNDEFINED*

55

39939753

12231687

379729

39949913

12231687

380999

48

13,

0,

0

0

0

0

0

0

0

64

0,

0,

35

39949913

12231687

380999

39965153

12231687

380999

64

4,

-39

3

12231687

380999

0

0

0

64

12231687

380999

39965153

12231687

396239

12231687

396239

39965153

12231687

404812

-39 -1

-1

-1

131

132

15,

0,

10000,

,

0

602

64

0,

0,

10000,ELBW,

9000

3011

64

3,

0,

10000,FLWN,

0

3001

8

39965153 PS-0311-3 8 9

8 67

8

36


105

39965153

-39

3 133

-1 -1

3011

8

-1

-1

9000

67

-1

-67

10000,ELBW,

*UNDEFINED*

-39

-1

0,

8

8

150 -22

0

66

-1 -1

3601

0

3

-1

-67

0

,

0,

8 67

8

110

39965153

12231687

404812

39965153

12231687

405129

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

130

39965153

12231687

405129

39965153

12231687

435609

64

7,

0,

10000,VVFL,

0

3202

-39

3

-1 -1

134

8 67

C - 44

-1


8

110

39965153

12231687

435609

39965153

12231687

435926

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

105

39965153

12231687

435926

39965153

12231687

444499

64

3,

0,

10000,FLWN,

0

3001

-39

3

12231687

444499

39965153

12231687

518159

64

5,

0,

10000,

0

3001

-1

144

-1 -1 -67

8 67

8 *UNDEFINED*

100

39965153

-39

5

-1

24

-1 -1 -67

,

8 67

8 *UNDEFINED*

40

39965153

12231687

518159

39965153

12231687

518159

64

5,

0,

10000,

,

0

3001

0

0

0

0

0

0

0

64

0,

0,

0,

,

0

0

39965153

12231687

518159

39954995

12231687

518159

48

10,

0,

10000,WTBW,

0

3001

10000,

,

0

3001

0,FLOW,

0

0

-39 -1

3 135

-1 -1

8

41 -67

8 67

*UNDEFINED*

42

39965153

12231687

518159

39965153

12231687

518159

64

5,

0,

149

39965153

12231687

543876

0

0

0

64

0,

0,

100

39965153

12231687

518159

39965153

12231687

569594

64

5,

0,

10000,

,

0

3001

12231687

569594

39965153

12231687

584834

64

4,

0,

10000,ELBW,

9000

3011

12231687

584834

39980393

12231687

584834

64

0,

0,

10000,ELBW,

9000

3011

12231687

584834

40030399

12231687

584834

64

5,

0,

10000,

,

0

3001

12231687

584834

40045639

12231687

584834

64

4,

0,

10000,ELBW,

9000

3011

12231687

584834

40045639

12231687

600074

64

0,

0,

10000,ELBW,

9000

3011

12231687

600074

40045639

12231687

615314

64

4,

0,

10000,ELBW,

9000

3011

12231687

615314

40045639

12246927

615314

64

0,

0,

10000,ELBW,

9000

3011

10000,REBW,

0

3601

0

0

-39

5

-1

24

-1 -1 -67

8 69

8 *UNDEFINED*

35

39965153

-39

3

-1

143

-1 -1

8

36 -67

8 69


100

39980393

-39

5

-1

23

-1 -1 -67

8 69

8 *UNDEFINED*

35

40030399

-39

3

-1

136

-1 -1

8

36 -67

8 69


35

40045639

-39

3

-1

137

-1 -1

8

36 -67

8 69


55

40045639

12246927

615314

40045639

12260897

618013

64

13,

0,

0

0

0

0

0

0

0

96

0,

0,

-39 -1

3 138

-1 -1 -67

8 69

8 *UNDEFINED*

0,

,


100

40045639

-39

5

-1

22

-1 -1 -67

40045639

12314396

618013

96

5,

12314396

618013

40045639

12324397

618013

96

16,

11774487

380999

39907050

11774487

380999

64

0,

0,

,

0

3001

0, 1110000,FLWN,

0

11

0,

10000,TEBW,

0

3001

10000,TEBW,

8

*UNDEFINED* 40045639 390311-W 39896573 *UNDEFINED*

45

39907050

11774487

380999

39917528

11774487

380999

64

6,

0,

0

0

0

0

0

0

0

64

0,

0,

39917528

11774487

380999

39917528

11764009

380999

64

0,

11764009

380999

39917528

11755436

380999

64

-39 -1

120

0,

10000,TEBW,

0

3011

3,

0,

10000,FLWN,

0

3001

8

*UNDEFINED* 39917528

-39

3 122

-1 -1

0

8

105

-1

3011

0

61

46 -67

0

,

0,

3

-1 -1

10000,

8

47 -67

618013

70

105 -30

12260897

8 62

8

110

39917528

11755436

380999

39917528

11755119

380999

64

1,

0,

10000,

,

0

2

95

39917528

11755119

380999

39917528

11754167

380999

64

17,

0,

10000,SB

,

0

3002

11754167

380999

39917528

11753214

380999

64

0,

0,

10000,SB

,

0

3002

11774487

380999

39928005

11774487

380999

64

0,

0,

10000,TEBW,

0

3011

11774487

380999

39936577

11774487

380999

64

3,

0,

10000,FLWN,

0

3001

-39 -1

3 123

-1 -1 -37 -1

8 OPERATE CLOSE D

96 -30

39917528 NOT FOUND

47 -67

8 62


105

39928005

-39

3

-1

121

-1 -1

8 63

8

110

39936577

11774487

380999

39936894

11774487

380999

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

130

39936894

11774487

380999

39972455

11774487

380999

64

18,

0,

10000,VGFL,

0

3502

-39

3

-1

209

-1 -1

8 63

8

110

39972455

11774487

380999

39972772

11774487

380999

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

105

39972772

11774487

380999

39981345

11774487

380999

64

3,

0,

10000,FLWN,

0

3001

-39

3

10000,TEBW,

-1

210

-1 -1 -67

8 63

8 *UNDEFINED*

45

39981345

11774487

380999

39991823

11774487

380999

64

6,

0,

0

0

0

0

0

0

0

64

0,

0,

39991823

11774487

380999

39991823

11764009

380999

64

0,

11764009

380999

39991823

11755436

380999

64

3,

-39 -1

46 -67

3011

0

0

0,

10000,TEBW,

0

3011

0,

10000,FLWN,

0

3011

3 211

-1 -1

0

,

0,

8 63

8

*UNDEFINED*

105

39991823

-39

3

C - 46

-1


215

8

-1 -1

107 8

110

39991823

11755436

380999

39991823

11755119

380999

64

1,

0,

10000,

,

0

2

95

39991823

11755119

380999

39991823

11754167

380999

64

17,

0,

10000,SB

,

0

3012

11754167

380999

39991823

11753214

380999

64

0,

0,

10000,SB

,

0

3012

11774487

380999

40002300

11774487

380999

64

0,

0,

10000,TEBW,

0

3011

10000,TEBW,

-39 -1

3 216

8

-1 -1 -37 -1

107 8 OPERATE CLOSE D

96 -30

39991823 NOT FOUND

47 -67


45

40002300

11774487

380999

40012778

11774487

380999

64

6,

0,

0

3001

0

0

0

0

0

0

0

64

0,

0,

0,

,

0

0

40012778

11774487

380999

0

0

0

64

19,

0,

10000,

,

0

602

11774487

380999

40012778

11774487

391477

64

0,

0,

10000,TEBW,

0

3001

0,FLOW,

-39 -1

3 237

-1 -1

8 108

8

150 -22

PS-0404-1

-39

8

-1

14

-1 -1

8 108

8

46 -67


149

40012778

11774487

419893

0

0

0

64

0,

0,

0

10

100

40012778

11774487

391477

40012778

11774487

448309

64

5,

0,

10000,

,

0

3011

11774487

448309

40012778

11774487

456882

64

3,

0,

10000,FLWN,

0

3011

-39

5

-1

64

-1 -1 -67

8 109

8 *UNDEFINED*

105

40012778

-39

3

-1

238

-1 -1

8 109

8

110

40012778

11774487

456882

40012778

11774487

457199

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

130

40012778

11774487

457199

40012778

11774487

487679

64

7,

0,

10000,VVFL,

0

3112

-39

3

-1

212

-1 -1

8 109

8

110

40012778

11774487

487679

40012778

11774487

487996

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

105

40012778

11774487

487996

40012778

11774487

496569

64

3,

0,

10000,FLWN,

0

3011

-39

3

11774487

496569

40012778

11774487

539114

64

5,

0,

10000,

,

0

3011

11774487

539114

40012778

11774487

554354

64

4,

0,

10000,ELBW,

9000

3011

-1

239

-1 -1 -67

8 109

8 *UNDEFINED*

100

40012778

-39

5

-1

65

-1 -1 -67

8 109

8 *UNDEFINED*

35

40012778

-39

3

-1

240

8


-1 -1

109 8

36 -67

40012778

35

40012778

-39

3

-1

241

-1 -1

40012778

5

-1

66

-1

242

-1

39619713

3 243

-1

40012778

11744007

554354

64

4,

0,

10000,ELBW,

9000

3011

11744007

554354

39997538

11744007

554354

64

0,

0,

10000,ELBW,

9000

3011

11744007

554354

39634953

11744007

554354

64

5,

0,

10000,

,

0

3011

11744007

554354

39619713

11744007

554354

64

4,

0,

10000,ELBW,

9000

3011

11744007

554354

39619713

11759247

554354

64

0,

0,

10000,ELBW,

9000

3011

11759247

554354

39619713

11774487

554354

64

4,

0,

10000,ELBW,

9000

3011

11774487

554354

39619713

11774487

539114

64

0,

0,

10000,ELBW,

9000

3011

11774487

539114

39619713

11774487

439737

64

5,

0,

10000,

,

0

3011

11774487

439737

39619713

11774487

431164

64

3,

0, 1110000,FLWN,

0

11

11774487

380999

40023255

11774487

380999

64

0,

0,

10000,TEBW,

0

3001

0,FLOW,

0

10

0

3011

8 109

8

36


100

39619713

-39

5

-1

67

-1

8 109

8 *UNDEFINED*

105

39619713 380407-W

47 -67

554354


-30

11759247

8

35

-1

3011

8

-39

-67

9000

109

36

-67

10000,ELBW,

*UNDEFINED*

3

-1

0,

8

39634953

-1

0,

8

-39

-67

64

109

35

-1

554354


-1

11759247

8

-39

-1

40012778

8

100

-67

554354

109

36 -67

11774487

*UNDEFINED*


149

40028017

11774487

380999

0

0

0

64

0,

0,

100

40023255

11774487

380999

40032780

11774487

380999

64

5,

0,

10000,

10000,TEBW,

-39

5

-1

63

8

-1 -1 -67

110 8 *UNDEFINED*

45

40032780

11774487

380999

40043258

11774487

380999

64

6,

0,

0

0

0

0

0

0

0

64

0,

0,

11774487

380999

40043258

11774487

391477

64

0,

11774487

391477

40043258

11774487

400049

64

3,

-39 -1

236

0,

10000,TEBW,

0

3001

0,

10000,FLWN,

0

3011

8 40043258 *UNDEFINED* 40043258

-39

3 246

-1 -1

0

8

105

-1

3001

0

110

46 -67

0

,

0,

3

-1 -1

,

8 111

8

110

40043258

11774487

400049

40043258

11774487

400366

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

130

40043258

11774487

400366

40043258

11774487

430847

64

7,

0,

10000,VVFL,

0

3112

-39

3

C - 48

-1

213

-1 -1


8 111

8

110

40043258

11774487

430847

40043258

11774487

431164

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

105

40043258

11774487

431164

40043258

11774487

439737

64

3,

0,

10000,FLWN,

0

3011

-39

3

0,FLOW,

-1

247

-1 -1 -67

8 111

8 *UNDEFINED*

149

40043258

11774487

519905

0

0

0

64

0,

0,

0

10

100

40043258

11774487

439737

40043258

11774487

600074

64

5,

0,

10000,

,

0

3011

11774487

600074

40043258

11774487

615314

64

4,

0,

10000,ELBW,

9000

3011

11774487

615314

40031549

11764729

615314

64

0,

0,

10000,ELBW,

9000

3011

11764729

615314

39877800

11636606

615314

64

5,

0,

10000,

,

0

3011

1

-39

5

-1

68

-1 -1 -67

8 111

8 *UNDEFINED*

35

40043258

-39

3

-1

248

-1 -1

8 111

8

36 -67


100

40031549

-39

5

-1

69

-1 -1 -67

8 111

8 *UNDEFINED*

35

39877800

11636606

615314

39866093

11626849

615314

64

4,

0, 1110000,ELBW,

9000

36

39866093

11626849

615314

39866093

11626849

630554

64

0,

0, 1110000,ELBW,

9000

1

100

39866093

11626849

630554

39866093

11626849

726281

64

5,

0, 1110000,

,

0

11

11774487

380999

40053735

11774487

380999

64

0,

0,

10000,TEBW,

0

3001

11774487

380999

40068975

11774487

380999

64

4,

0,

10000,ELBW,

9000

3001

11774487

380999

0

0

0

64

20,

0,

10000,

,

0

602

11774487

380999

40068975

11774487

396239

64

0,

0,

10000,ELBW,

9000

3001

0,FLOW,

-30

380404-W

47 -67


35

40053735

-39

3

-1

235

-1 -1

8 112

8

150 -22

40068975 PS-0404-2

-39

8

-1

15

-1 -1

8 112

8

36 -67


149

40068975

11774487

422274

0

0

0

64

0,

0,

0

10

100

40068975

11774487

396239

40068975

11774487

448309

64

5,

0,

10000,

,

0

3011

11774487

448309

40068975

11774487

456882

64

3,

0,

10000,FLWN,

0

3011

-39

5

-1

62

-1 -1 -67

8 113

8 *UNDEFINED*

105

40068975

-39

3

-1

234

-1 -1

8 113

8

110

40068975

11774487

456882

40068975

11774487

457199

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

130

40068975

11774487

457199

40068975

11774487

487679

64

7,

0,

10000,VVFL,

0

3112


-39 -1

3 214

-1 -1

8 113

8

110

40068975

11774487

487679

40068975

11774487

487996

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

105

40068975

11774487

487996

40068975

11774487

496569

64

3,

0,

10000,FLWN,

0

3011

-39

3

11774487

496569

40068975

11774487

539114

64

5,

0,

10000,

,

0

3011

11774487

539114

40068975

11774487

554354

64

4,

0,

10000,ELBW,

9000

3011

11774487

554354

40068975

11789727

554354

64

0,

0,

10000,ELBW,

9000

3011

11789727

554354

40068975

11804967

554354

64

4,

0,

10000,ELBW,

9000

3011

11804967

554354

40053735

11804967

554354

64

0,

0,

10000,ELBW,

9000

3011

11804967

554354

39609235

11804967

554354

64

5,

0,

10000,

,

0

3011

-1

233

-1 -1 -67

8 113

8 *UNDEFINED*

100

40068975

-39

5

-1

61

-1 -1 -67

8 113

8 *UNDEFINED*

35

40068975

-39

3

-1

232

-1 -1

8 113

8

36 -67


35

40068975

-39

3

-1

231

-1 -1

8 113

8

36 -67


100

40053735

-39

5

-1

60

-1 -1 -67

8 113

8 *UNDEFINED*

35

39609235

11804967

554354

39593995

11804967

554354

64

4,

0, 1110000,ELBW,

9000

11

36

39593995

11804967

554354

39593995

11789727

554354

64

0,

0, 1110000,ELBW,

9000

11

11774487

380999

39855615

11774487

380999

64

0,

0,

10000,TEBW,

0

3001

11774487

380999

39847042

11774487

380999

64

3,

0,

10000,FLWN,

0

3001

-30

380407-W

47 -67


105

39855615

-39

3

-1

117

-1 -1

8 58

8

110

39847042

11774487

380999

39846725

11774487

380999

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

130

39846725

11774487

380999

39816244

11774487

380999

64

7,

0,

10000,VVFL,

0

3502

-39

3

-1

118

-1 -1

8 58

8

110

39816244

11774487

380999

39815927

11774487

380999

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

39815927

11774487

380999

39807355

11774487

380999

64

3,

0, 1110000,FLWN,

0

1

11626849

859948

39855615

11626849

859948

64

0,

0,

10000,TEBW,

0

3011

0,FLOW,

0

10

0

3011

105 -30

380408-W

47 -67


149

39845535

11626849

859948

0

0

0

64

0,

0,

100

39855615

11626849

859948

39835454

11626849

859948

64

5,

0,

-39 -1

5 34

8

10000,

,

C - 50

-1 -1 -67


72 8 *UNDEFINED*

35

39835454

-39

3

-1

156

-1 -1

11626849

859948

64

4,

0,

10000,ELBW,

9000

3001

11626849

859948

39820214

11626849

844708

64

0,

0,

10000,ELBW,

9000

3001

11626849

844708

39820214

11626849

836135

64

3,

0,

10000,FLWN,

0

3011

8 39820214 *UNDEFINED* 39820214

-39

3 114

-1 -1

39820214

8

105

-1

859948

72

36 -67

11626849

8 53

8

110

39820214

11626849

836135

39820214

11626849

835818

64

1,

0,

10000,

,

0

2

115

0

0

0

0

0

0

12

2,

0,

8,

,

0

2

-31

38E-104/ N1$4

-1

IN RFFE 300

-20

XDABBZZQSG

-21

GASKET, CL300

-1

, G653, 0.125

-1

" THK, 304 SP

-1

IRAL WND, GRA

-1

PH FILLED, CS

-1

CENTER RING,

-1

API-601

-88

7

-20

YZZZHZZFFF

-21

B31, ASTM-A19

-1

3-B7 STUDS W/

-1

ASTM-A194-2H

-1

HVY HEX NUTS,

-1

4.5"

-1

ENGTH

BOLT L

-85

4.5

-88

7

-20

FAABBAWAAA

-21

FLANGE, CL300

-1

, RFFE/BE, AS

-1

TM-A105, ANSI

-1

-B16.5, WN, S

-1

-STD BORE

-80

FWN

-81

CL300

-82

RFFE

-83

A105

-84

ANSI-B16.5

-20

WAAAAAWAAA

-21

ELBOW, S-STD,

-1

<— TEST

-80

E90LR

-81

S-STD

-82

BE

-83

A234-WPB

-84

ANSI-B16.9

-20

PAAAAAWAAA

-21

PIPE, S-STD,

-1

BE, ASTM-A53-

-1

B TYPE S

-80

PIPE

-81

S-STD

-82

BE

-83

A53-B

-84

ANSI-B36.10M


-20

WTAAAAWAAA

-21

TEE, S-STD, B

-1

E, ASTM-A234-

-1

WPB, ANSI-B16

-1

.9

-80

T

-81

S-STD

-82

BE

-83

A234-WPB

-84

ANSI-B16.9

-20

VABBAHCAAA

-21

GATE VALVE, C

-1

L300, RFFE, B

-1

B, OS&Y, ASTM

-1

-A216-WCB, TR

-1

IM 8, CRANE 3

-1

3

-80

GAT

-81

CL300

-82

RFFE

-83

A216-WCB

-84

ANSI-B16.10

-20

PS-0311-1

-21

PIPE SUPPORT.

-1

GENERIC DESC

-1

RIPTION FOR L

-1

EVEL 3 TESTIN

-1

G.

-80

PSP2

-20

WADAAAWAAA

-21

45 DEG LR ELB

-1

OW, S-STD, BE

-1

, ASTM-A234-W

-1

PB, ANSI-B16.

-1

9

-80

E45LR

-81

S-STD

-82

BE

-83

A234-WPB

-84

ANSI-B16.9

-20

WOAAAAWAFA

-21

WELDOLET, S-S

-1

TD X S-STD, B

-1

E, ASTM-A105

-80

WOL

-81

S-STD

-82

BE

-83

A105

-84

BONNEY FORGE

-1

1

-20

YZZZHZZFFF

-21

B31, ASTM-A19

-1

3-B7 STUDS W/

-1

ASTM-A194-2H

-1

HVY HEX NUTS,

-1

4.25"

-1

LENGTH

BOLT

-85

4.25

-88

7

-20

PS-0311-2

-21

PIPE SUPPORT.

-1

GENERIC DESC

-1

RIPTION FOR L

-1

EVEL 3 TESTIN

-1

G.

C - 52


-80

PSP2

-20

WRBAAAWAAA

-21

ECCENTRIC RED

-1

UCER, S-STD X

-1

S-STD BORE,

-1

BE, ASTM-A234

-1

-WPB, ANSI-B1

-1

6.9

-80

REDE

-81

S-STD

-82

BE

-83

A234-WPB

-84

ANSI-B16.9

-20

38LV-559

-21

INSTRUMENT 38

-1

LV-559. GENER

-1

IC DESCRIPTIO

-1

N FOR LEVEL 3

-1

TESTING.

-80

1GL1

-81

300QD

-82

RFFE

-84

ANSI-B16.5

-20

PS-0311-3

-21

PIPE SUPPORT.

-1

GENERIC DESC

-1

RIPTION FOR L

-1

EVEL 3 TESTIN

-1

G.

-80

PSP2

-20

FGPBBAWAAA

-21

ORIFICE FLANG

-1

E, CL300, RFF

-1

E/BE, ASTM-A1

-1

05, ANSI-B16.

-1

36, WN, ONE 0

-1

.5" SWE TAP,

-1

S-STD BORE

-80

FOWNAW

-81

CL300

-82

RFFE

-83

A105

-84

ANSI-B16.36

-20

GJGBBZZADA

-21

SPECTACLE BLA

-1

NK, CL300, RF

-1

TBE, ASTM-A51

-1

6-70, API-590

-1

Z1, 0.75 THK

-80

BLSPC

-81

CL300

-82

RFTBE

-83

A516-70

-84

API-590Z1

-20

VBBBAHCGAA

-21

GLOBE VALVE,

-1

CL300, RFFE,

-1

BB, OS&Y, AST

-1

M-A216-WCB, T

-1

RIM 8, CRANE

-1

151

-80

GLO

-81

CL300

-82

RFFE

-83

A216-WCB


-84

ANSI-B16.10

-20

PS-0404-1

-21

PIPE SUPPORT.

-1

GENERIC DESC

-1

RIPTION FOR L

-1

EVEL 3 TESTIN

-1

G.

-80

PSP2

-20

PS-0404-2

-21

PIPE SUPPORT

-1

PS-0404-2. GE

-1

NERIC DESCRIP

-1

TION FOR LEVE

-1

L 3 TESTING.

-80 999

PSP2

C - 54


C.5 Interface Error Log (.err file) __________________________________________________________________________________________________________________________________________________ PDSIDF version 4.03.01.00 - 6.0.8

Begin Input ———————————————-

Options file pdssdr:/usr/cert/iso/isoref/john.def

Model design file(s) 40pipe01 - type 63 information extracted from this model 39pipe01

(CONT. ONLY)

39pipe02

(CONT. ONLY)

40eqp01 40foot01

Iso design file pdssdr:/usr/cert/john/400104wc.i*

Line id(s) 400104-WC

Piping area PArea40

Project database pd_oxs_l3

Batch options N Y Y N * * Y * * 22-Feb-1993 check plots

Extraction number 6

End input ————————————————

*** WARNING - W20 *** Header record attribute is undefined Header record number:

-41

*** WARNING - W39 *** Segment data table look-up failed File name: /usr/ip32/pdiso/dat/isoc.note Table Key: 40/40





*** WARNING - W39 *** Segment data table look-up failed File name: /usr/ip32/pdiso/dat/isoc.note Table Key: 1C0031



1 - ERROR -

key ’S19’ was not found in SPECIALTY material description library.

2 - ERROR -

key ’PSUPPORT PSL’ was not found in SPECIALTY material description library.

*** WARNING - W14 *** Error reading specialty material description library Item code

: S19

Alt. index

: PSUPPORT

Return code :

-1

3 - ERROR -

key ’SP-0104-1’ was not found in SPECIALTY material description library.

4 - ERROR -

key ’PSPECIALTY NREQD STRT1 TEFLTEXX’ was not found in SPECIALTY material description library.


: SP-0104-1

Alt. index

: PSPECIALTY

Return code :

-1




5 - ERROR -

key ’SP-0104-2’ was not found in SPECIALTY material description library.

6 - ERROR -

key ’PSPECIALTY NREQD STRT1 TEFLTEXX’ was not found in SPECIALTY material description library.


: SP-0104-2

Alt. index

: PSPECIALTY

Return code :

-1


C - 56



7 - ERROR -

key ’S15’ was not found in SPECIALTY material description library.

8 - ERROR -

key ’PSUPPORT PSL’ was not found in SPECIALTY material description library.


: S15

Alt. index

: PSUPPORT

Return code :

-1




*** WARNING - W39 *** Segment data table look-up failed File name: /usr/ip32/pdiso/dat/isoc.note Table Key: 1C0031 ISOGEN INTERGRAPH VERSION 6.0.8

DRG.

1

/400104-WCPLOTTED

DRG.

2

/400104-WCPLOTTED


C.6 MTO Neutral File (.b# file) __________________________________________________________________________________________________________________________________________________ GASK400104-WC- 401572887

1572914

7

XDABBZZQSG

4.0"

BOLT400104-WC- 401572887

1572914

7

YZZZHZZFFF

19.05

COMP400104-WC- 401572887

1572914

15 N

FAABBAWAAA

4.0" 4.0" NREQDS-STD0.0000.00090.00

COMP400104-WC- 401572887

1572915

15 N

WRBAAAWAAA

6.0" 4.0" S-STDS-STD0.0000.00090.00

COMP400104-WC- 401572888

1572916

7

N

POCAAAOAAE

1.0" 1.0" S-160S-1603.0003.00090.00

COMP400104-WC- 401572888

1572917

7

N

VAUSAHGAAA

1.0" 1.0" NREQDNREQD3.0000.00090.00

COMP400104-WC- 401572888

1572918

7

N

POCAAAOAAE

1.0" 1.0" S-160S-1603.0003.00090.00

COMP400104-WC- 401572888

1572919

7

N

SCAQZZZAAA

1.0"

COMP400104-WC- 401572889

1572920

15 N

WAAAAAWAAA

6.0" 6.0" S-STDS-STD228.50.00090.00

SUPP400104-WC- 401572889

1572868

COMP400104-WC- 401572889

1572921

15 N

FAAABAWAAA

6.0" 6.0" NREQDS-STD0.0000.00090.00

GASK400104-WC- 401572889

1572922

7

XDAABZZQSG

6.0"

BOLT400104-WC- 401572889

1572922

7

YZZZHZZFFF

19.05

ENGR400104-WC- 401572889

1572922

SP-0104-1

6.0" 6.0" NREQDNREQD

GASK400104-WC- 401572893

1572923

7

XDAABZZQSG

6.0"

BOLT400104-WC- 401572893

1572923

7

YZZZHZZFFF

19.05

COMP400104-WC- 401572893

1572923

7

VAABAHCCAA

6.0" 6.0" NREQDNREQD3.0000.00090.00

GASK400104-WC- 401572893

1572924

7

XDAABZZQSG

6.0"

BOLT400104-WC- 401572893

1572924

7

YZZZHZZFFF

19.05

COMP400104-WC- 401572893

1572924

15 N

FAAABAWAAA

6.0" 6.0" NREQDS-STD0.0000.00090.00

PIPE400104-WC- 401572893

1572878

15 1

PAAAAAWAAA

6.0" 6.0" S-STDS-STD

COMP400104-WC- 401572893

1572926

15 N

WAAAAAWAAA

6.0" 6.0" S-STDS-STD228.50.00090.00

PIPE400104-WC- 401572893

1572927

15 1

PAAAAAWAAA


COMP400104-WC- 401572893

1572925

15 N

WTAAAAWAAA

6.0" 6.0" S-STDS-STD0.0000.00090.00

PIPE400104-WC- 401572886

1572876

15 2

PAAAAAWAAA


COMP400104-WC- 401572886

1572913

15 N

FAAABAWAAA

6.0" 6.0" NREQDS-STD0.0000.00090.00

GASK400104-WC- 401572886

1572912

7

XDAABZZQSG

6.0"

BOLT400104-WC- 401572886

1572912

7

YZZZHZZFFF

19.05

114.3

NREQD

8

0.0000.00090.00

S19

N

N

101.6

8

101.6

8

101.6

8

-9999

-9999

-9999

101.6

***********

***********

***********

8

C - 58


PIPE400104-WC- 401572884

1572926

15 8

PAAAAAWAAA


COMP400104-WC- 401572884

1573096

15 N

WAAAAAWAAA

6.0" 6.0" S-STDS-STD228.50.00090.00

PIPE400104-WC- 401572884

1572925

15 1

PAAAAAWAAA


COMP400104-WC- 401572884

1572908

15 N

WAAAAAWAAA

6.0" 6.0" S-STDS-STD228.50.00090.00

PIPE400104-WC- 401572884

1572870

15 2

PAAAAAWAAA


COMP400104-WC- 401572884

1572874

15 N

WAAAAAWAAA

6.0" 6.0" S-STDS-STD228.50.00090.00

COMP400104-WC- 401572884

1572873

15 N

FAAABAWAAA

6.0" 6.0" NREQDS-STD0.0000.00090.00

GASK400104-WC- 401572884

1572872

7

XDAABZZQSG

6.0"

COMP400104-WC- 401572884

1572872

7

GJGABZZADA

6.0" 6.0" NREQDNREQD0.0000.00090.00

GASK400104-WC- 401572884

1572872

7

XDAABZZQSG

6.0"

BOLT400104-WC- 401572884

1572872

7

YZZZHZZFFF

19.05

N

-9999

-9999

-9999

127.0

***********

***********

***********

8


C.7 ISOGEN Message File (.msg file) __________________________________________________________________________________________________________________________________________________ ISOGEN WORKSTATION VERSION 5.4.1

ERROR DETECTED IN PIPE /W010 (35:1062) WARNING - PIPE CONFLICT (PIPE ON/OFF MATERIAL LIST - CHECK CUT LENGTHS

DRG.

1

/W0101 PLOTTED

C - 60


C.8 ISOGEN Printed Parts File (.prt file) __________________________________________________________________________________________________________________________________________________ 1

PAGE 1

PIPELINE REF 400104-WC- SHT 1 OF 2

—————— | SHOP MATERIALS | —————— PT

NPD

NO

DESCRIPTION

–

(IN)

———–

–

CMDTY CODE —– —-

QTY

—

1

PIPE, S-STD, BE, ASTM-A53-B TYPE S

6

PAAAAAWAAA

22.9’

2

TEE, S-STD, BE, ASTM-A234-WPB,

6X6

WTAAAAWAAA

1

6X4

WRBAAAWAAA

1

6

WAAAAAWAAA

5

6

FAAABAWAAA

4

4

FAABBAWAAA

1

ANSI-B16.9 3

ECCENTRIC REDUCER, S-STD X S-STD BORE, BE, ASTM-A234-WPB, ANSI-B16.9

4

90 DEG LR ELBOW, S-STD, BE, ASTM-A234-WPB, ANSI-B16.9

5

FLANGE, CL150, RFFE/BE, ASTM-A105, ANSI-B16.5, WN, S-STD BORE

6


—————————– | OTHER THAN SHOP MATERIALS | —————————– PT

NPD

NO

DESCRIPTION

–

(IN)

———– 7

–

ERROR READING SPECIALTY MATERIAL


QTY

—

6X6

SP-0104-1

1

6

GJGABZZADA

1

NIPPLE, PE, S-160, 3" LONG, ASTM-A106-B

1

POCAAAOAAE

2

10

CAP, CL3000, SWE, ASTM-A105

1

SCAQZZZAAA

1

11

GASKET, CL150, G653, 0.125" THK, 304

6

XDAABZZQSG

6

4

XDABBZZQSG

1

3/4

YZZZHZZFFF

8

3/4

YZZZHZZFFF

32

3/4

YZZZHZZFFF

8

6

VAABAHCCAA

1

1

VAUSAHGAAA

1

6

S19

1

DESCRIPTION LIBRARY 8

SPECTACLE BLANK, CL150, RFTBE, ASTM-A516-70, API-590Z1, ****** THK

9

SPIRAL WND, GRAPH FILLED, CS CENTER RING, API-601 12

GASKET, CL300, G653, 0.125" THK, 304 SPIRAL WND, GRAPH FILLED, CS CENTER RING, API-601

13

B31, ASTM-A193-B7 STUDS W/ASTM-A194-2H HVY HEX NUTS, 4.5"

14


15

BOLT LENGTH


16

BOLT LENGTH

BOLT LENGTH

GATE VALVE, CL150, RFFE, BB, OS&Y, ASTM-A216-WCB, TRIM 8, CRANE 47

17

GATE VALVE, CL800, SWE, BB, OS&Y, ASTM-A105, TRIM 8, SMITH 800

PIPE SUPPORTS ————18

ERROR READING SPECIALTY MATERIAL DESCRIPTION LIBRARY


PIECE MARKS ———– 400104-WC40-1 400104-WC40-2 1

PAGE 2


1

PAGE 1


—————— | SHOP MATERIALS | —————— PT

NPD

NO

DESCRIPTION

–

(IN)

———– 1

–

ECCENTRIC REDUCER, S-STD X S-STD BORE,


QTY

—

6X4

WRBAAAWAAA

1

6

WAAAAAWAAA

1

6

FAAABAWAAA

1

4

FAABBAWAAA

1

BE, ASTM-A234-WPB, ANSI-B16.9 2

90 DEG LR ELBOW, S-STD, BE, ASTM-A234-WPB, ANSI-B16.9

3


4


—————————– | OTHER THAN SHOP MATERIALS | —————————– PT

NPD

NO

DESCRIPTION

–

(IN)

———– 5

–

ERROR READING SPECIALTY MATERIAL


QTY

—

6X6

SP-0104-2

1

DESCRIPTION LIBRARY 6

NIPPLE, PE, S-160, 3" LONG, ASTM-A106-B

1

POCAAAOAAE

2

7

CAP, CL3000, SWE, ASTM-A105

1

SCAQZZZAAA

1

8

GASKET, CL150, G653, 0.125" THK, 304

6

XDAABZZQSG

2

4

XDABBZZQSG

1

3/4

YZZZHZZFFF

16

3/4

YZZZHZZFFF

8

6

VAABAHCCAA

1

1

VAUSAHGAAA

1

6

S15

1

SPIRAL WND, GRAPH FILLED, CS CENTER RING, API-601 9

GASKET, CL300, G653, 0.125" THK, 304 SPIRAL WND, GRAPH FILLED, CS CENTER RING, API-601

10


11


12

BOLT LENGTH

BOLT LENGTH

GATE VALVE, CL150, RFFE, BB, OS&Y, ASTM-A216-WCB, TRIM 8, CRANE 47

13

GATE VALVE, CL800, SWE, BB, OS&Y, ASTM-A105, TRIM 8, SMITH 800

PIPE SUPPORTS ————14

ERROR READING SPECIALTY MATERIAL DESCRIPTION LIBRARY

PIECE MARKS ———– 400104-WC40-3

C - 62


C.9 ISOGEN Component versus Sheet Number File (.sed file) __________________________________________________________________________________________________________________________________________________ 1

5

282

0

297

0

1

U1001-P-SHT-1 SPL-1-

1

3

590

0

297

0

1


1

5

283

0

297

0

1


1

3

591

0

297

0

1


1

3

580

0

297

0

1


1

3

579

0

297

0

1


1

5

284

0

297

0

1


1

3

578

0

297

0

1


1

3

577

0

297

0

1


1

6

61

0

297

0

0

0


C.10 ISOGEN Cut Pipe Report (.cut file) __________________________________________________________________________________________________________________________________________________ 1 SUMMARY OF CUT PIPE LENGTHS FOR PROJECT NUMBER FOR PIPELINE REFERENCES

PAGE

1

DATE

28/02/93

400104-WC-

ITEM

ITEM DESCRIPTION AND SPECIFICATION

CODE

PAAAAAWAAA

PIPE, S-STD, BE, ASTM-A53-B TYPE S

SIZE

CUT LENGTH

SPECIAL

PIECE

PIPELINE

BATCH

(INS)

(FT & INS)

REQ.

NO.

REFERENCE

REFERENCE

6

7.1/16

<1>

400104-WC-

6

5’3.3/8

<2>

400104-WC-

6

10.7/16

<3>

400104-WC-

6

2’9.3/8

<4>

400104-WC-

6

5’10.1/8

<5>

400104-WC-

6

7’6.1/16

<6>

400104-WC-

SUB TOTAL

22’10.7/16

C - 64


C.11 Title Block Table (.bit, .seg and .dwg files) __________________________________________________________________________________________________________________________________________________ ! Description= Definition of the ISOGEN title block for size C batch isos. ! Rev=2

By=

Ckd By=

Date=

! SHEET_DATA_TABLE 2

!2 lines to follow

0, 0,

0, 1,

6

!Sheet no

0, 0,

0, 2,

7

!of sheet no

DRAWING_DATA_TABLE 49

!49 lines to follow

5, 1,

1, 979, 0,

11

!Company name

5, 1,

2, 979, 0,

12

!Plant name

5, 1,

3, 979, 0,

1

5, 1,

4, 979, 0,

10

1, 1,

0, 951, 0,

5

!Project no !Unit name !Iso no

3, 2, 10,

0, 0,

15

!Extraction date

3, 2, 11,

0, 0,

96

!Extraction no

3, 1,

2,

0, 0,

90

!Dgn file 1

3, 1,

3,

0, 0,

91

!Dgn file 2

3, 1,

4,

0, 0,

92

!Dgn file 3

3, 1,

5,

0, 0,

93

!Dgn file 4

3, 1,

6,

0, 0,

94

!Dgn file 5

3, 1, 22,

0, 0,

95

!Defaults file

3, 2, 15,

0, 0,

8

3, 2, 16,

0, 0,

20

!REV no

3, 2, 20,

0, 0,

21

!Date

3, 2, 17,

0, 0,

22

!BY initials

3, 2, 18,

0, 0,

23

!CHK initials

3, 2, 23,

0, 0,

24

!Description

3, 2, 16,

1, 0,

30

!REV no

3, 2, 20,

1, 0,

31

!Date

3, 2, 17,

1, 0,

32

!BY initials

3, 2, 18,

1, 0,

33

!CHK initials

3, 2, 23,

1, 0,

34

!Description

3, 2, 16,

2, 0,

40

!REV no

3, 2, 20,

2, 0,

41

!Date

3, 2, 17,

2, 0,

42

!BY initials

3, 2, 18,

2, 0,

43

!CHK initials

3, 2, 23,

2, 0,

44

!Description

3, 2, 16,

3, 0,

50

!REV no

3, 2, 20,

3, 0,

51

!Date

3, 2, 17,

3, 0,

52

!BY initials

3, 2, 18,

3, 0,

53

!CHK initials

3, 2, 23,

3, 0,

54

!Description

3, 2, 16,

4, 0,

60

!REV no

3, 2, 20,

4, 0,

61

!Date

3, 2, 17,

4, 0,

62

!BY initials

3, 2, 18,

4, 0,

63

!CHK initials

3, 2, 23,

4, 0,

64

!Description

3, 2, 16,

5, 0,

70

!REV no

3, 2, 20,

5, 0,

71

!Date

3, 2, 17,

5, 0,

72

!BY initials

3, 2, 18,

5, 0,

73

!CHK initials

3, 2, 23,

5, 0,

74

!Description

3, 2, 90,

0, 0,

2

3, 2, 91,

0, 0,

97

!User attribute 2

3, 2, 92,

0, 0,

98

!User attribute 3

3, 2, 93,

0, 0,

99

!User attribute 4

3, 2, 94,

0, 0, 100

!User attribute 5

!Current rev no

!Color code (User attribute 1)


SEGMENT_DATA_TABLE 20 1, 12,

!20 lines to follow 2,

0,

11, 25, 1, 200, 25

!Line no

1, 12, 35,

0,

36, 12, 0, 201, 25

!Dgn std

1, 12, 24,

0,

48,

5, 0, 202, 25

!Nor oper press

1, 12, 25,

0,

53,

4, 0, 203, 25

!Nor oper temp

1, 12, 28,

0,

57,

5, 0, 204, 25

!Nor dgn press

1, 12, 29,

0,

62,

4, 0, 205, 25

!Nor dgn temp

1, 12, 26,

0,

66,

5, 0, 206, 25

!Alt oper press

1, 12, 27,

0,

71,

4, 0, 207, 25

!Alt oper temp

1, 12, 30,

0,

75,

5, 0, 208, 25

!Alt dgn press

1, 12, 31,

0,

80,

4, 0, 209, 25

!Alt dgn temp

1, 12, 64,

0,

84,

5, 0, 210, 25

!Test system no

1, 12, 65,

0,

89,

3, 0, 211, 25

!Test fluid

1, 12, 66,

0,

92,

5, 0, 212, 25

!Test press

1, 12, 17,

0,

97,

3, 0, 213, 25

!Heat tracing reqmts

1, 12, 18,

0, 100,

3, 0, 214, 25

!Heat media

1, 12, 19,

0, 103,

4, 0, 215, 25

!Heat media temp

1, 12, 14,

0, 107,

6, 0, 216, 25

!Insulation purpose

1, 12, 15,

0, 113,

5, 0, 217, 25

!Insulation thickness

1, 12, 40,

0, 118,

8, 0, 218, 25

!Coating reqmts

1, 12,

0, -992, 126, 25, 1, 219, 25

!PWHT reqmts

C - 66


Appendix D: PDS Database Table Formats D - 1

Appendix D

__________________________________________________________________________________________________________________________________________________

PDS Database Table Formats

D-2



Appendix D

__________________________________________________________________________________________________________________________________________________

PDS Database Table Formats This section contains PDS database formats, including: Design table format

Spec table format (Imperial & Metric)

D-4


D.1 Piping Design Database Table Format __________________________________________________________________________________________________________________________________________________ # Piping Design Database

# Default Relational Database Definition

# Piping Segment Data

table number = 12 , number of columns = 73

1

, system_unique_no

, integer

2

, line_number_label

, character(40)

3

, line_id

, character(16)

4

, unit_number

, character(12)

5

, unit_code

, character(3)

6

, module_no

, character(16)

7

, package_system_no

, character(12)

8

, train_number

, character(2)

9

, fluid_code

10 , line_sequence_no

, short

, index 1

, standard note 125

, character(16)

11 , nominal_piping_dia , short 12 , piping_mater_class , character(16) 13 , gasket_separation

, character(8)

14 , insulation_purpose , short 15 , insulation_thick

, standard note 220

, double

16 , insulation_density , double

, standard note 1074 (units)

17 , heat_tracing_reqmt , short

, standard note 200

18 , heat_tracing_media , short

, standard note 210

19 , heat_tracing_temp

, double

20 , construction_stat

, short

21 , hold_status

, short

, standard note 50

22 , approval_status

, short

, standard note 35

23 , schedule_override

, character(8)

24 , nor_oper_pres

, double

25 , nor_oper_temp

, double

26 , alt_oper_pres

, double

27 , alt_oper_temp

, double

28 , nor_dgn_pres

, double

29 , nor_dgn_temp

, double

30 , alt_dgn_pres

, double

31 , alt_dgn_temp

, double

32 , steam_outlet_temp

, double

, standard note 130

33 , mater_of_construct , character(6) 34 , safety_class

, short

, standard note 340

35 , design_standard

, short

, standard note 570

36 , design_area_number , character(12) 37 , design_resp

, short

, standard note 160

38 , construction_resp

, short

, standard note 160

39 , supply_resp

, short

, standard note 160

40 , coating_reqmts

, short

, standard note 190

41 , cleaning_reqmts

, short

, standard note 230

42 , fluid_category

, character(4)

43 , nor_op_pres_units

, short

, standard note 1064

44 , nor_op_temp_units

, short


45 , alt_op_pres_units

, short


46 , alt_op_temp_units

, short


47 , nor_dgn_pres_units , short


48 , nor_dgn_temp_units , short


49 , alt_dgn_pres_units , short


50 , alt_dgn_temp_units , short



51 , steam_temp_units

, short

52 , stress_system_no

, character(12)

53 , stress_reqmts

, short

54 , hyd_system_no

, character(12)

55 , hyd_reqmts

, short


, standard note 360

, standard note 360

56 , specific_gravity_a , double 57 , specific_gravity_b , double 58 , specific_gravity_c , double 59 , viscosity

, double

60 , density

, double

61 , spec_heat_ratio

, double

62 , sonic_velocity

, double

63 , surface_roughness

, double

64 , test_system_no

, character(6)

65 , test_fluid

, short

66 , test_pressure

, double

67 , PID_id_part_a

, character(4)

68 , PID_id_part_b

, character(4)

69 , end_1_nozzle_id

, integer

70 , end_2_nozzle_id

, integer

71 , alpha_descript_id

, character(12)

72 , standard_note_no

, short

73 , pid_index_no

, integer

, standard note 125

, standard note 499

# Piping Component Data


1

, system_unique_no

, integer

2

, piping_comp_no

, character(20)

3

, commodity_name

, character(6)

4

, model_code

, character(6)

5

, option_code

, short

6

, maximum_temp

, double

7

, sched_thick_basis

, character(8)

8

, commodity_code

, character(16)

9

, MTO_requirements

, short

, standard note 365

10 , fabrication_cat

, short

, standard note 180

11 , source_of_data

, short

, standard note 420

12 , PDS_sort_code

, character(6)

13 , physical_data_id

, character(8)

14 , geometric_standard , short 15 , weight_code

, index 1

, standard note 400

, standard note 575

, short

, standard note 578

16 , table_suffix_green , short

, standard note 576

17 , table_suffix_red

, short

, standard note 577

18 , materials_grade

, short

, standard note 145

19 , bend_radius

, double

20 , bend_angle

, double

21 , face_to_face_dim

, double

22 , dimension_a

, double

23 , dimension_b

, double

24 , dimension_c

, double

25 , surface_area

, double


26 , empty_weight

, double


27 , water_weight

, double


28 , operator_weight

, double

29 , operator_sym_name

, character(6)

30 , chain_operator_no

, short

31 , opening_action

, short

, standard note 390


, short

, standard note 130

33 , hold_status

, short

, standard note 50


, standard note 200


, standard note 210


, double

37 , iso_dwg_index_no

, integer

D-6


38 , isometric_sheet_no , character(2) 39 , piece_mark_no

, character(10)

40 , color_code

, character(8)

41 , stress_node_no

, short

42 , stress_intens_fact , double 43 , head_loss_factor

, double

44 , piping_assembly

, character(12)

45 , component_group_no , short 46 , remarks

, character(16)

47 , standard_note_no_a , short

, standard note 499

48 , standard_note_no_b , short

, standard note 499

49 , cp_1_nom_pipe_diam , short 50 , cp_1_outside_diam

, double

51 , cp_1_end_prep

, short

52 , cp_1_sch_thk

, character(8)

53 , cp_1_rating

, character(8)

54 , cp_1_face_to_ctr

, double

55 , cp_1_weld_no

, character(8)

56 , cp_1_weld_type

, short

57 , cp_1_gasket_gap

, double

58 , cp_1_gasket_option , short 59 , cp_1_stress_node

, standard note 330

, standard note 1100 / 400 (bolt option)

, standard note 400

, short

60 , cp_1_stress_factor , double 61 , cp_1_head_loss

, double


, double

64 , cp_2_end_prep

, short

65 , cp_2_sch_thk

, character(8)

66 , cp_2_rating

, character(8)


, double

68 , cp_2_weld_no

, character(8)

69 , cp_2_weld_type

, short


, double


, standard note 330


, standard note 400

, short


, double


, double

77 , cp_3_end_prep

, short

78 , cp_3_sch_thk

, character(8)

79 , cp_3_rating

, character(8)


, double

81 , cp_3_weld_no

, character(8)

82 , cp_3_weld_type

, short


, double


, standard note 330


, standard note 400

, short


, double


, double

90 , cp_4_end_prep

, short

91 , cp_4_sch_thk

, character(8)

92 , cp_4_rating

, character(8)


, double

94 , cp_4_weld_no

, character(8)

95 , cp_4_weld_type

, short


, double


, short

99 , cp_4_stress_factor , double 100, cp_4_head_loss

, double

, standard note 330


, standard note 400


101, cp_5_nom_pipe_diam , short 102, cp_5_outside_diam

, double

103, cp_5_end_prep

, short

104, cp_5_sch_thk

, character(8)

105, cp_5_rating

, character(8)

106, cp_5_face_to_ctr

, double

107, cp_5_weld_no

, character(8)

108, cp_5_weld_type

, short

109, cp_5_gasket_gap

, double

110, cp_5_gasket_option , short 111, cp_5_stress_node

, standard note 330


, standard note 400

, short

112, cp_5_stress_factor , double 113, cp_5_head_loss

, double

# Piping/Tubing Data


1

, system_unique_no

, integer

2

, piping_comp_no

, character(20)

3

, commodity_name

, character(6)

4

, model_code

, character(6)

5

, option_code

, short

6

, maximum_temp

, double

7

, nominal_piping_dia , short

8

, outside_diameter

9

, schedule_thickness , character(8)

10 , sched_thick_basis

, index 1

, standard note 400

, double

, character(8)

11 , rating

, character(8)

12 , commodity_code

, character(16)

13 , MTO_requirements

, short

, standard note 365


, short

, standard note 180

15 , source_of_data

, short

, standard note 425

16 , PDS_sort_code

, character(6)


, standard note 575

, short

, standard note 578


, standard note 576


, short

, standard note 577


, short

, standard note 145

22 , pipe_length

, double

23 , surface_area

, double


24 , empty_weight

, double


25 , water_weight

, double


26 , cold_spring_length , double 27 , construction_stat

, short

28 , hold_status

, short

, standard note 130 , standard note 50


, standard note 200


, standard note 210


, double


, integer


, character(10)

35 , color_code

, character(8)


, character(12)


, character(16)


, standard note 499


, standard note 499

41 , end_1_end_prep

, short

, standard note 330

42 , end_1_weld_no

, character(8)

43 , end_1_weld_type

, short

44 , end_1_gasket_gap

, double

45 , end_1_gasket_opt

, short

46 , end_1_stress_node

, short

47 , end_1_stres_int

, double

48 , end_1_head_loss

, double


, standard note 400

D-8


49 , end_2_end_prep

, short

50 , end_2_weld_no

, character(8)

51 , end_2_weld_type

, short

52 , end_2_gasket_gap

, double

53 , end_2_gasket_opt

, short

54 , end_2_stress_node

, short

55 , end_2_stres_int

, double

56 , end_2_head_loss

, double

, standard note 330


, standard note 400

# Instrument Component Data


1

, system_unique_no

2

, instrument_comp_no , character(20)

, integer

3

, model_code

4

, option_code

, short

5

, sched_thick_basis

, character(8)

6

, MTO_requirements

, short

, standard note 365

7

, fabrication_cat

, short

, standard note 180

8

, source_of_data

, short

, standard note 430

9

, PDS_sort_code

, character(6)

10 , physical_data_id

, character(8)

, character(6)


, index 1

, standard note 400

, standard note 575

, short

, standard note 578


, standard note 576


, short

, standard note 577


, short

, standard note 145

16 , face_to_face_dim

, double

17 , dimension_a

, double

18 , dimension_b

, double

19 , dimension_c

, double

20 , surface_area

, double


21 , empty_weight

, double


22 , water_weight

, double


23 , operator_weight

, double


24 , operator_type

, double

25 , operator_sym_name

, character(6)

26 , chain_operator_no

, short

27 , chain_length

, double

28 , opening_action

, short

, standard note 390


, short

, standard note 130

30 , hold_status

, short

, standard note 50

31 , design_resp

, short

, standard note 160

32 , construction_resp

, short

, standard note 160


, standard note 200


, standard note 210


, double

36 , insulation_purpose , short 37 , insulation_thick

, standard note 220

, double

38 , insulation_density , double


39 , cleaning_reqmts

, short

, standard note 230

40 , safety_class

, short

, standard note 340

41 , module_no

, character(16)

42 , package_system_no

, character(12)


, integer


, character(10)

46 , color_code

, character(8)

47 , stress_node_no

, short

48 , stress_intens_fact , double 49 , head_loss_factor

, double


, character(12)


, character(16)


, standard note 499


, standard note 499



, double

57 , cp_1_end_prep

, short

58 , cp_1_sch_thk

, character(8)

59 , cp_1_rating

, character(8)


, double

61 , cp_1_weld_no

, character(8)

62 , cp_1_weld_type

, short


, double


, standard note 330


, standard note 400

, short


, double


, double

70 , cp_2_end_prep

, short

71 , cp_2_sch_thk

, character(8)

72 , cp_2_rating

, character(8)


, double

74 , cp_2_weld_no

, character(8)

75 , cp_2_weld_type

, short


, double


, standard note 330


, standard note 400

, short


, double


, double

83 , cp_3_end_prep

, short

84 , cp_3_sch_thk

, character(8)

85 , cp_3_rating

, character(8)


, double

87 , cp_3_weld_no

, character(8)

88 , cp_3_weld_type

, short


, double


, standard note 330


, standard note 400

, short


, double


, double

96 , cp_4_end_prep

, short

97 , cp_4_sch_thk

, character(8)

98 , cp_4_rating

, character(8)


, double

100, cp_4_weld_no

, character(8)

101, cp_4_weld_type

, short


, double


, standard note 330


, standard note 400

, short


, double

107, cp_5_nom_pipe_diam , short 108, cp_5_outside_diam

, double

109, cp_5_end_prep

, short

110, cp_5_sch_thk

, character(8)

111, cp_5_rating

, character(8)

112, cp_5_face_to_ctr

, double

113, cp_5_weld_no

, character(8)

114, cp_5_weld_type

, short


, double

, standard note 330


D - 10



, standard note 400

, short


, double

# Pipe Support Data


1

, system_unique_no

, integer

2

, pipe_support_no

, character(20)

3

, model_code_phy

, character(6)

4

, model_code_log

, character(6)

5

, iso_support_type_a , short

, standard note 380

6

, iso_support_type_b , short

, standard note 380

7

, iso_support_type_c , short

, standard note 380

8

, iso_support_type_d , short

, standard note 380

9

, details_for_shop

10 , details_for_field

, index 1

, character(50) , character(50)

11 , fabrication_orient , character(20) 12 , commodity_code

, character(16)

13 , MTO_requirements

, short

, standard note 365


, short

, standard note 180

15 , weight

, double



, short

, standard note 130

17 , hold_status

, short

, standard note 50

18 , standard_note_no

, short

, standard note 499


, integer


, character(10)

22 , color_code

, character(8)

23 , isometric_dim_a

, double

24 , isometric_dim_b

, double

25 , isometric_dim_c

, double

26 , isometric_dim_d

, double

27 , isometric_dim_e

, double

28 , trans_rigidity_x

, double

29 , trans_rigidity_y

, double

30 , trans_rigidity_z

, double

31 , rot_rigidity_x

, double

32 , rot_rigidity_y

, double

33 , rot_rigidity_z

, double

34 , spring_gap_length

, double

35 , sping_gap_direct

, short

36 , number_of_springs

, short


D.2 Specification/Material Reference Database Table Format __________________________________________________________________________________________________________________________________________________ # Specification/Material Reference Database

# Default Relational Database Definition

# Piping Materials Class Data

table number = 201, number of columns = 21

1 , system_unique_no

, integer

2 , piping_mater_class , character(16) 3 , revision_no

, character(2)

4 , version_no

, character(2)

5 , revision_date

, character(10)

6 , fluid_code

, character(6)

, standard note 125

7 , mater_of_construct , character(6) 8 , corrosion_allow

, double

9 , mat_description

, short

10, service_lim_table

, character(6)

11, diameter_table

, character(6)

12, thickness_table

, character(6)

13, materials_table

, character(6)

, standard note 148

14, thickness_equation , character(6) 15, branch_table

, character(6)

16, tap_data_table

, character(6)

17, vent_drain_macro

, character(6)

18, gasket_separation

, character(8)

19, standard_note_no_a , short

, standard note 499

20, standard_note_no_b , short

, standard note 499

21, revision_mngt_date , integer

# Piping Commodity Specification Data



, integer

2 , piping_mater_class , character(16) 3 , commodity_name

, character(6)

4 , option_code

, short

5 , maximum_temp

, double

6 , gcp_from_nom_diam

, short

7 , gcp_to_nom_diam

, short

8 , gcp_end_prep

, short

9 , gcp_rating

, character(8)

10, gcp_sch_thk

, character(8)

11, gcp_table_suffix

, short

12, rcp_from_nom_diam

, short

13, rcp_to_nom_diam

, short

14, rcp_end_prep

, short

15, rcp_rating

, character(8)

16, rcp_sch_thk

, character(8)

17, rcp_table_suffix

, short

18, commodity_code

, character(16)

19, model_code

, character(6)

20, PDS_sort_code

, character(6)

21, modifier

, double

, index 1

, standard note 400

, standard note 330

, standard note 576

, standard note 330

, standard note 577

22, geometric_standard , short

, standard note 575

23, weight_code

, standard note 578

, short

D - 12


24, fabrication_cat

, short

, standard note 180

25, materials_grade

, short

, standard note 145


, standard note 499


, standard note 499

# Piping Specialty Specification Data



, integer

2 , piping_comp_no

, character(20)

3 , model_code

, character(6)

4 , option_code

, short


, short

6 , gcp_to_nom_diam

, short

7 , gcp_end_prep

, short

8 , gcp_rating

, character(8)

9 , gcp_sch_thk

, character(8)


, short


, short

12, rcp_to_nom_diam

, short

13, rcp_end_prep

, short

14, rcp_rating

, character(8)

15, rcp_sch_thk

, character(8)


, short

17, physical_data_id

, character(8)

18, PDS_sort_code

, character(6)

19, modifier

, double


, standard note 400

, standard note 330

, standard note 576

, standard note 330

, standard note 577

, standard note 575

21, weight_code

, short

, standard note 578

22, fabrication_cat

, short

, standard note 180

23, materials_grade

, short

, standard note 145


, standard note 499


, standard note 499

# Instrument Component Specification Data



, integer

2 , instrument_comp_no , character(20) 3 , model_code

, character(6)

4 , option_code

, short


, short

6 , gcp_to_nom_diam

, short

7 , gcp_end_prep

, short

8 , gcp_rating

, character(8)

9 , gcp_sch_thk

, character(8)


, short


, short

12, rcp_to_nom_diam

, short

13, rcp_end_prep

, short

14, rcp_rating

, character(8)

15, rcp_sch_thk

, character(8)


, short

17, physical_data_id

, character(8)

18, PDS_sort_code

, character(6)

19, modifier

, double


, standard note 400

, standard note 330

, standard note 576

, standard note 330

, standard note 577

, standard note 575

21, weight_code

, short

, standard note 578

22, fabrication_cat

, short

, standard note 180

23, materials_grade

, short

, standard note 145


, standard note 499


, standard note 499


# Tap Properties Data



, integer

2 , tap_table_name

, character(6)

3 , nominal_piping_dia , short 4 , option_code

, short

, standard note 400

5 , end_preparation

, short

, standard note 330

6 , rating

, character(8)

7 , sched_thick

, character(8)

8 , tap_material_code

, character(10)

# Piping Commodity Size-Dependent Material Data



, integer

2 , sys_commodity_code , character(16) 3 , gcp_nom_diam

, short

4 , rcp_nom_diam

, short

5 , gcp_sch_thk

, character(8)

6 , rcp_sch_thk

, character(8)

7 , commodity_code

, character(16)

8 , weld_weight

, double

9 , unit_price

, double

10, manhours

, double

, index 1

# Piping Commodity Implied Material Data



, integer

2 , sys_commodity_code , character(16) 3 , gcp_from_nom_diam

, short

4 , gcp_to_nom_diam

, short

5 , rcp_from_nom_diam

, short

6 , rcp_to_nom_diam

, short

7 , commodity_code

, character(16)

8 , quantity

, double

9 , fabrication_cat

, short

10, standard_note_no

, short

, index 1

# Reference Database Revision Management Data


1 , specialty_rev_date , integer 2 , instr_rev_date

, integer

3 , tap_data_rev_date

, integer

4 , size_data_rev_date , integer 5 , implied_rev_date

, integer

D - 14


Appendix E: ISOGEN SKEY Dimensions

Appendix E

E-1

__________________________________________________________________________________________________________________________________________________

ISOGEN SKEY Dimensions

E-2



Appendix E

E-3

__________________________________________________________________________________________________________________________________________________

ISOGEN SKEY Dimensions

E-4


ARFL: Valve - Angle Relief/Vent

AVFL: Valve - Angle

AXFL: Valve - Angle Pressure Reducing


BAFL: Block - Angle

BOFL: Block - Offset

BRFL: Block

E-5

E-6


C3FL: Valve - Three-Way Control

C4FL: Valve - Four-Way Control

CAFL: Valve - Angle Control


CEBW: Coupling - Elbolet (Butt Weld)

CESC: Coupling - Elbolet (Screwed)

CESW: Coupling - Elbolet (Socket Weld)

E-7

E-8


CHFL: Hose Coupling

CKFL: Valve - Check

COCP: Coupling - Compression


COSC: Coupling - Screwed

COSW: Coupling - Socket Weld

CPBW: Reducer - Concentric Fabricated from Plate

E-9

E - 10


CPFL: Reducer - Concentric Fabricated from Plate (Flanged)

CSBW: Reducer - Concentric Swaged From Plate

CSFL: Reducer - Concentric Swaged From Plate (Flanged)


CTBW: Reducer - Concentric with a Connection (Butt Weld)

CTFL: Reducer - Concentric with a Connection (Flanged)

CTSC: Reducer - Concentric with a Connection (Screwed)

E - 11

E - 12


CTSW: Concentric with a Connection (Socket Weld)

CVFL: Valve - Control

CXBW: Reducer - Concentric with a Connection Swaged from Pipe


E - 13

CXFL: Reducer - Concentric with a Connection Swaged from Pipe (Flanged)

CZBW: Reducer - Concentric with a Connection Fabricated from Plate

CZFL: Reducer - Concentric with a Connection Fabricated from Plate (Flanged)

E - 14


DR: Rupture Disk

EPBW: Reducer - Eccentric Fabricated from Plate

EPFL: Reducer - Eccentric Fabricated from Plate (Flanged)


EPSW: Reducer - Eccentric Fabricated from Plate (Socket Weld)

ESBW: Reducer - Eccentric Swaged from Pipe

ESFL: Reducer - Eccentric Swaged from Pipe (Flanged)

E - 15

E - 16


EXBW: Reducer - Eccentric with a Connection Swaged from Pipe

EXFL: Reducer - Eccentric with a Connection Swaged from Pipe (Flanged)

EXFL: Expansion Bellows


E - 17

EZBW: Reducer - Eccentric with a Connection Fabricated from Plate

EZFL: Reducer - Eccentric with a Connection Fabricated from Plate (Flanged)

FAFL: Filter/Strainer - Angle

E - 18


FIFL: Filter/Strainer - Straight Through

FLBL: Flange - Blind

FLFL: Flange - Flared/Loose Backing


FLLB: Flange - Backing

FLOW: Flow Arrow

FLRC: Flange - Reducing Concentric

E - 19

E - 20


FLRE: Flange - Reducing Eccentric

FLRG: Lap Joint - Ring Loose

FLSC: Flange - Screwed


FLSE: Lap Joint - Stub End Loose

FLSJ: Flange - Slip On with J-type Weld

FLSO: Flange - Slip On

E - 21

E - 22


FLSW: Flange - Socket Weld

FLWN: Flange - Weld Neck

FOFL: Filter/Strainer - Offset


FOSO: Flange - Orifice (Slip On)

FOWN: Flange - Orifice (Weld Neck)

FPPL: Fixed Length Pipe - Without Flanged Ends

E - 23

E - 24


FRFL: Filter/Strainer - Return

FTFL: Flame Trap

FXFL: Filter/Strainer - Return


H3FL: Valve - Three-Way Control (Hand Indicator)

H4FL: Valve - Four-Way Control (Hand Indicator)

HAFL: Valve - Angle Control (Hand Indicator)

E - 25

E - 26


HCSC: Olet - Half Coupling (Screwed)

HCSW: Olet - Half Coupling (Socket Weld)

HVFL: Valve - Control Hand Indicator


IAFL: Instrument - Angle

IDFL: Instrument - Dial (Flanged)

IDPL: Instrument - Dial

E - 27

E - 28


IIFL: Instrument

IOFL: Instrument - Offset

IRFL: Instrument - Return


ITFL: Instrument - Tee

KABW: Cap - Butt Weld

KACP: Cap - Compression

E - 29

E - 30


KASC: Cap - Screwed

KASW: Cap - Socket Weld

LABW: Olet - Latrolet (Buttweld)


M3FL: Valve - Three-Way Control (Motorized Indicator)

M4FL: Valve - Four-Way Control (Motorized Indicator)

MAFL: Valve - Angle Control (Motorized Indicator)

E - 31

E - 32


MVFL: Valve - Control (Motorized Indicator)

NBSC: Nipple - Screwed

NCFL: Non-Category Item


NIPL: Olet - Nipolet (Plain End)

NISC: Olet - Nipolet (Screwed)

NRSC: Nipple - Screwed

E - 33

E - 34


OP: Orifice Plate

OTBW: Reducer - Eccentric with a Connection (Butt Weld)

OTFL: Reducer - Eccentric with a Connection (Flanged)


OTSC: Reducer - Eccentric with a Connection (Screwed)

PF: Pipe Block - Fixed Length

PL: Plug

E - 35

E - 36


PR: Restrictor Plate

PV: Pipe Block - Variable Length

RAFL: Valve - Angle (Relief/Vent)


RBSC: Reducer - Concentric (Screwed Bush)

RBSW: Reducer - Concentric (Socket Weld)

RCBW: Reducer - Concentric (Butt Weld)

E - 37

E - 38


RCCP: Reducer - Concentric (Compression)

RCFL: Reducer - Concentric (Flanged)

RCSC: Reducer - Concentric (Screwed)


RCSW: Reducer - Concentric (Socket Weld)

RD: Rupture Disk

REBW: Reducer - Eccentric (Butt Weld)

E - 39

E - 40


REFL: Reducer - Eccentric (Flanged)

RESC: Reducer - Eccentric (Screwed)

RF: Reducer - Special Reducing Flange


RFPL: Reducer - Connection Block

RNSC: Reducer - Concentric (Nipple)

RP: Restrictor Plate

E - 41

E - 42


RVFL: Valve - Relief/Vent

S3FL: Valve - Three-Way Control (Square Indicator)

S4FL: Valve - Four-Way Control (Square Indicator)


SAFL: Valve - Angle Control (Square Indicator)

SB: Specticle - Blind

SGFL: Sight Glass

E - 43

E - 44


SKSW: Olet - Sockolet

SP: Slip Plate

SR: Slip Ring


SVFL: Valve - Control (Square Indicator)

SWBw: Olet Sweepolet

TAFL: Trap - Angle

E - 45

E - 46


THSC: Olet - Thredolet

TIFL: Trap - Inline Straight Through

TOFL: Trap - Offset


TRFL: Trap - Return

TUFL: Tundish (Funnel)

E - 47

E - 48


UNSC: Union - Screwed

UNSW: Union - Socket Weld

V3FL: Valve - Three-Way


V4FL: Valve - Four-Way

VBFL: Valve - Ball

VCFL: Valve - Check

E - 49

E - 50


VDFL: Valve - Diaphragm

VGFL: Valve - Globe

VKFL: Valve - Cock


VNFL: Valve - Needle

VPFL: Valve - Plug

VRFL: Valve - Relief/Vent

E - 51

E - 52


VSFL: Valve - Slide

VTFL: Valve - Gate

VVFL: Valve - Basic


VXFL: Valve - Pressure Reducing

VYFL: Valve - Butterfly

WTBW: Olet - Weldolet

E - 53

E - 54


XAFL: Valve - Angle (Pressure Reducing)

XVFL: Valve - Pressure Reducing

01HG: Support/Hanger


E - 55

01SP: Used on valves with AV, V3, V4, VD, VG or VV as the first two characters of their skeys

02SP: Used on valves with AR, RA, VR as the first two characters of their skeys.

03SP: Used on valves with VB, VK, VY as the first two characters of their skeys.

E - 56


04SP: Not Used

05SP: Used on valves with VT as the first two characters of their skeys.

06SP: Used on valves with VN as the first two characters of their skeys.


E - 57

07SP: Used on valves with VP as the first two characters of their skeys.

08SP: Used on valves with VS as the first two characters of their skeys.

09SP: Used on valves with AX, VX or XA as the first two characters of their skeys.

E - 58


10SP: Used on valves with SA, SV, S3 or S4 as the first two characters of their skeys.

11SP: Used on valves with MA, MV, M3 or M4 as the first two characters of their skeys.

Glossary GL - 1

Glossary

__________________________________________________________________________________________________________________________________________________

GL - 2


Glossary GL - 3

Glossary

__________________________________________________________________________________________________________________________________________________

absolute path name

The sequence of directories, beginning with the root directory (/) that locates a file. See also path name and relative path name.

active depth

The plane in a 3-D design upon which you can place elements and perform manipulations.

active process

The process which is displayed in the Process ID field; it controls the message fields, the menus, and the keyboard. The active process has a highlighted window icon strip.

application software

Software designed to meet specific needs, unlike system software which runs other software.

batch processing

A method of processing data which collects a series of operations into a group (or ‘‘batch’’) and executes the group in a continuous stream without user intervention.

batch queue

A queue, or channel for moving requests, created through NQS. A batch queue handles scheduling for processes submitted through the Batch options screen menu.

branch point

A point on a pipeline which separates piping segments so that they can be assigned different segment parameters. A branch point allows for placement of branch components.

cancel button

The button located in the upper right corner of a form containing a red X or the word cancel. Select the cancel button to exit the form or option.

cell

A permanent association of elements that can be stored and placed as a group, and then manipulated as individual elements.

character

A column data type that stores alphanumeric character data.

client

In network operations, a node which accesses data or performs a function on the remote resource (usually a server). All network operations (database, NFS, NQS) between two or more nodes establish a client/server relationship.

column

An attribute of a database table. A group of columns defines a table in a database.

command

Instructions from the user to perform a function on specified data.

GL - 4


confirm button

A button that appears in the upper right corner of a form and contains a green check mark or the word confirm. Select the confirm button to initiate a specified option.

coordinate

The location of a point along the X, Y, or Z axis.

coordinate system

A geometric relation used to denote the location of points in the design cube. The most common coordinate system is the rectangular coordinate system, whereby points are located by traversing the X, Y, and Z axes of the design cube. Normally, coordinate systems have their origin defined as 0,0,0, though this is not required. Other coordinate systems are used to more easily express the coordinates of specific geometric entities. For example, you can use a spherical coordinate system to help define points on a sphere, and you can use a cylindrical coordinate system to help define points on a cylinder.

coordinates

An ordered set of absolute or relative data values that specify a location in a coordinate system.

core files

The image files written by System V for a number of reasons, the most common of which are memory violations, illegal instructions, bus errors, and user-generated quit signals.

cursor

The pointer that the user moves on the screen to indicate an item or area.

data button

The mouse button used to place data points and tentative points, to accept previously selected elements, and to select commands from forms and menus.

data entry field

The field on a screen used to accept user-supplied data. Also known as key-in field.

data point

A point placed by pressing the data button on the mouse. Data points select commands from the panel menus and Menu Bar, place elements, identify and accept elements, and activate windows and perform window manipulations.

database

A collection of comprehensive informational files having predetermined structure and organization that can then be communicated, interpreted, or processed by a specific program.

database table

The part of the database that is made of rows and columns and contains information about the project and design elements.

default

The predetermined value of a parameter that is automatically supplied by the system or program whenever a value is not specified by the user.

Glossary GL - 5

delete

To remove, destroy, eliminate, or erase.

delimiter

A separating mark or space; a character or sequence of contiguous characters that mark the end of a string of characters.

device

A nonaddressable component of a network, that is, a component onto which a user cannot log, for example, tape drive, disk drive, and floppy disk.

directory

A file that contains the names of other files.

display-list box

A small box with horizontal dashes located at the end of a form key-in field. When selected, a list of the data available for that field is displayed. Input can then be selected from the list with a data point instead of keying in the information.

domain

The set of acceptable values for a value within a component.

dragging

Another term for the dynamic function that attaches the cursor to an element so you can see it move.

easting

A term used in plane surveying that describes an east, or positive, difference in longitude.

entity

An object (project, drawing, element, and so forth.) of interest about which information is stored; a relational database table.

envelope file

See interference envelope.

filename

A user-defined name given to an interactively created file. The name should be relevant to the contents of the file.

form

An interface or screen menu designed with the I/FORMS product. Because many of the screen menus in the application software are built with I/FORMS, you must have the FORMS_S product on your workstation.

full path name

The name of the entire path or directory hierarchy to a file, including the file name. See also relative path name.

gadget

A portion of a form, such as a button, a field, or a checklist, that responds to information. Gadgets can display default values or act as data entry areas.

header

The first items of information in a file which precede any actual data. The header contains information on the structure and contents of the file.

hierarchy

A classified structure with superiors (roots) and subordinates (dependents) for grouping files or commands.

icon

A pictorial representation or image; a symbol that graphically identifies a command.

GL - 6


Informix

A relational database management system supported by RIS.

Ingres


interference envelope

An equipment modeling primitive or parametric component that is used in conjunction with or instead of model graphics for interference checking. Interference envelopes are given different levels and display symbology to distinguish them from primitives.

invert elevation

The lowest point on the internal diameter of the pipe.

isometric

Relating to or being a drafting system characterized by three equal axes at right angles; a view in which the horizontal lines of an element are drawn at an angle to the horizontal and all verticals are projected at an angle from the base.

key

An attribute (column) in a table which is chosen as the access vehicle to individual rows of the table.

key-in field

The field on a screen used to accept user-supplied data. Also known as a data entry field.

keypoint

A point on an element, including vertices, to which you can snap.

keyword

A word recognized by the software that provides access to a certain function.

menubar

The strip at the top of the screen that contains icons for selecting commands.

message area

The area that appears in the MicroStation Command Window when you are working in a design file. It is divided into the Command Status field, the Current Command field, the Prompt field, and the Key-in field.

model

A graphic representation or schema.

network

An interconnection of host computers and workstations that enables them to share data and control. The term network can mean the devices that connect the system, or it can mean the connected system.

NFS

Network File System, the system that provides access to data that is distributed among machines through an interconnection of host computers and workstations. NFS allows you to mount a remote resource to your local workstation so you can access the data as though it were local. NFS is usually used to access centralized data on a server.

node

Any addressable device (such as a workstation or a server) that is connected to a network. The network enables the connected nodes to share data and system control.

Glossary GL - 7

node address

The hard-wired Ethernet address assigned to each node when it is manufactured. It is necessary for each node to identify and communicate with another node in the network.

node name

A name, or alias, that can be assigned to the node address of a device on a network.

northing

A term used to describe a north coordinate location in the plant coordinate system.

nozzle

A special equipment modeling primitive that contains the connection point to piping. This point does NOT include a gasket allowance, but rather represents the face-of-flange coordinate.

NQS

Network Queuing System, the software package that allows you to define network-wide batch and device queues. Use of NQS involves setting up local resource queues on the system(s) where the resources reside and setting up ‘‘pipe queues’’ on the systems that are to have access to the resources.

Oracle


origin

In coordinate geometry, the point where the x, y, and z-axes intersect.

origin point

The point at which the coordinate system is placed.

orthogonal view

A view which is a projection of the model onto a plane along lines which are orthogonal to the plane.

parameter

A property whose value determines the characteristics or behavior of something.

path

A sequence of directories leading to a file or a sequence of menus leading to a command.

path name

The sequence of directories leading to a file. See also absolute path name and relative path name.

PDS

Plant Design System

pipe queue

A controlled channel for moving requests to batch or device queues on remote systems and for receiving status and/or data in response.

place data point

To identify a specific element, or indicate a specific point in the design file.

plane

A spatial element in geometry that may or may not have a boundary, but is level, having no elevations or depressions, and is three-dimensional.

GL - 8


RDB

Reference Database.

reference database

A collection of reference data containing information relative to industry design codes, vendor’s catalog data, job specifications, commodity libraries, graphics symbology, label descriptions, report formats and other information of a similar manner.

relative path name

The sequence of directories leading from the current directory to a particular file. See also path name and absolute path name.

rotate

To turn; to change the angular orientation; to transform by revolution about a specific axis.

row

A unit of related information in a table. One collection of column values for a table.

rubberbanding

The animation dynamic that enables you to specify the position of a data point while the element changes as you move the cursor.

schema

A description of the overall structure of the rulebase or database.

schema file

A file that outlines the overall logical structure of a rule base or a database.

server

In network operations, the node which maintains common data or performs a common task needed by clients. All network operations (database, NFS, NQS) between two or more nodes establish a client/server relationship.

Structured Query Language SQL

Language developed by IBM for creating, modifying, and querying relational databases.

style

The symbology of an element such as continuous dashes, dash-dot, solid, and so forth.

surface

The skin of a three-dimensional geometric element.

symbology

The display style of an element, including color, style, and weight.

table

A collection of data for quick reference, either stored in sequential locations in memory or printed as an array of rows and columns of data items of the same type.

toggle

To switch; to change between two alternatives.

user name

A name that provides access to an account on the system.

values

Data, either entered by the user or determined by the software, that are stored in an attribute.

Glossary GL - 9

variable

A quantity that may assume any one of a set of values.

vector

A quantity possessing both magnitude and direction, generally represented as a line. Vectors can be manipulated geometrically and are represented as a coordinate triple (x,y,z).

view

The defined area of vision on a screen. A view allows you to see a prescribed volume of the design cube. Views are created with their own x, y, and z axes. The x,y plane of the view is parallel to the screen, while the z-axis can be thought of as coming straight out of the view towards you. The view axes maintain this relationship regardless of the rotation with respect to the design cube. See also active depth.

virtual memory

External memory for a computer that can be used as if it were an extension of the computer’s internal memory. The software uses virtual memory to store data. This means that unneeded files and data, stay on the disk until they are called for. Because the internal processing memory stores a minimal amount of data, the software can perform processing more quickly.

working directory

The directory from which you are accessing files.

GL - 10


Index IN - 1

Index

__________________________________________________________________________________________________________________________________________________

IN - 2


Index IN - 3

Index

__________________________________________________________________________________________________________________________________________________

01HG symbol key B-46 01SP symbol key B-62 02SP symbol key B-62 03SP symbol key B-62 04SP symbol key B-62 05SP symbol key B-62 06SP symbol key B-62 07SP symbol key B-62 08SP symbol key B-62 09SP symbol key B-62 10SP symbol key B-62 11SP symbol key B-62 12SP symbol key B-63 13SP symbol key B-63 A accept 5-81 add default set 5-15 Alias ISOGEN tables B-3 allocation weld number reinforcement pads 77 B-34 slip-on flanges 77 B-34 alphanumeric commodity library 7-19 alternate indices for the MDL defining 7-87 alternate_description_index 7-87 example defining secondary or alternate indices for the MDL 7-87 alternative text B-64 AR** symbol key B-60 area drawing option switch 35 B-20 arrow flow option switch 17 B-14 size of flow option switch 112 B-39 ASCII to binary conversion 1-4 assemble isometric symbol 5-76 assembling a symbol accept 5-81 clear 5-82

assembling a symbol (continued) define end point 5-80 lagging 5-81 solid line 5-81 spindle point 5-81 start point 5-80 tap points 5-81 tracing 5-81 delete 5-82 exit 5-82 fit symbol 5-80 atext 7-51 specifications ingr 7-58 AText by category B-75 cut lists B-80 isometric drawing area B-75 line summary B-84 plotted material B-80 printed material list B-85 specification changes B-79 title block B-79 weld box summary standard B-85 user-defined B-86 AText facility by number B-65 atext_specifications 7-56 ATEXT_SPECIFICATIONS example modify text for eccentric reducers 7-56 modifying text 7-56 automatic split points in pipe option switch 108 B-38 AV** symbol key B-59 AX** symbol key B-59 B b# file example of C-57 BA** symbol key B-45 balloon instrument

IN - 4


balloon (continued) instrument (continued) option switch 123 B-41 basic input data 6-12 batch data file 5-1, 9-1, 10-9 table 10-1, 10-7 extraction problems 4-7 extraction software error messages A-32 generation 5-9 isometric extraction 5-1 create batch job input 5-89 drawing 5-28 delete drawing 5-46 listing drawings 5-54 revise drawing 5-33 iso area 5-25 utilities 5-56 generation 5-9 job input creating 5-89 file 4-3 export variable 5-4 scheduling 5-100 submitting 5-100 job log file 5-101 options file 5-3 processes 2-8 reference 5-36, 5-50, 5-94, 5-107 number 5-30, 5-39, 5-43 software organization 4-1 batch job input file 4-3 filling in the title block (stib) 4-6 generating title block input (tblock) 4-6 interface job creation (jobctl.exe) 4-4 investigating batch extraction problems 4-7 ISOGEN 4-5 interface (pdsidf.exe) 4-5 making a run log entry (pdsidf) 4-7 plotting 4-7 updating the project database 4-7 BEFL symbol key B-51 bend radius symbol keys B-43

bend/elbow representation 20-5 bending parameters file 7-44 bends symbol keys B-51 zero length option switch 68 B-28 binary conversion 1-4 bit file example of C-64 block test parameter option switch 127-140 B-42 BO** symbol key B-45 bolt diameters material control file option switch 65 B-26 lengths 7-8 material control file option switch 65 B-26 bolt diameters 7-8 bolt units 8-10 bom welds listed in 16-10 border file 5-3 export variable 5-4 bore output 7-24 box box dimension standout triangles, skew option switch 100 B-37 part number option switch 73 B-29 skew type option switch 96 B-37 style and dimensioning, skew option switch 99 B-37 weld number option switch 75 B-31 BR** symbol key B-45 branch dimension of tapped option switch 121 B-40 first order 6-22 nesting extraction limitations 3-20 scale of tapped option switch 120 B-40 supports 7-14 welds 12-9 branch dimensioning suppressing 17-2

Index IN - 5

break flanged pipe 7-41 breaking composite attributes by combining insulation purpose and thickness 7-54 supply responsibility along a pipeline 7-53 breaks specification option switch 114 B-39 BTFL symbol key B-51 BU+D symbol key B-52 BUFL symbol key B-51 bulk load lines 5-57 from ASCII file 5-67 bulk load lines from ASCII export variable 5-4 C C3** symbol key B-48 C4** symbol key B-48 CA** symbol key B-48 caps symbol keys B-53 carry-over dimension option switch 117 B-40 cc 7-70 CEBW symbol key B-53 cell library detail sketch facility 7-43 center of gravity and the STIB data file 19-2 appearing in the MTO 19-2 report file 19-2 weight display 19-2 weight library 7-43 calculating 19-2 centerline dimensioning valves option switch 80 B-34 centerline dimensions for valves 17-2 CESC symbol key B-53 CESW symbol key B-53 CH** symbol key B-45 chain wheel operators 7-20 changing construction responsibility along a pipeline 7-53 character size option switch 4 B-9 CK** symbol key B-60 clear 5-82

cn 7-70 COCP symbol key B-53 codelist values standard note 180 & 1100 16-3 cogmto.tbl 19-2 column reference structural 7-37 commodity library alphanumeric 7-19 common data table 12-1 common_record_data 12-1 − 12-2 component data table 12-1 name tapped 13-3 tags 7-15 vrs sheet number file 7-6 component vs sheet number file example of C-62 component_attributes 12-1, 12-4 extracting inspection numbers 12-6 components transferring between sort groups 8-9 configure.dat file 5-6 connect points 13-3 items 5-77 connect points skey B-43 connections, other end symbol keys B-50 control coordinate output option switch 66 B-27 dimensioning option switch 81 B-35 file, materials bolt lengths and diameters option switch 65 B-26 frame option switch 18 B-14 insulation option switch 61 B-25 printed material list length option switch 63 B-26 tracing option switch 62 B-26 weld option switch 54 B-25 conventions forms 2-5 limitations 3-19 extraction conventions 3-19 limitations 3-20

IN - 6


coordinate features 17-3 output 17-1 system 7-12 tap point option switch 122 B-41 coordinate features related information 17-1 coordinates display elevation at bend/elbow intersections 17-3 at branch intersections 17-4 split point coordinates 17-4 extend witness line 17-3 copy default set 5-21 correcting incorrect sheet splits 15-5 COSC symbol key B-53 COSW symbol key B-53 couplings symbol keys B-53 CP symbol key B-50 CPBW symbol key B-57 CPFL symbol key B-57 CRBW symbol key B-54 CRCP symbol key B-54 create batch job input 5-12, 5-89 delete existing files 5-91 incrementing revision number 5-92 plotting 5-92 save previous details 5-92 drawing 5-11, 5-28 notes table 11-1 creating isometric seed file 9-1 plot request files 9-3 seed files for extraction 9-1 user-defined symbol library 5-83 CRFL symbol key B-54 crosses symbol keys B-54 CRRF symbol key B-54 CRSC symbol key B-54 CRSO symbol key B-54 CRSW symbol key B-54 CSBW symbol key B-57 CSFL symbol key B-57 ct 7-70 CTBW symbol key B-57

CTSC symbol key B-58 cut file example of C-63 cut lists AText B-80 cut marks option switch 3 B-9 cut pipe report 7-6 example of C-63 cutting list option switch 2 B-9 CV** symbol key B-48 CXBW symbol key B-57 CXFL symbol key B-57 CZBW symbol key B-57 CZFL symbol key B-57 D data file batch 10-9 return file option switch 109 B-39 table batch 10-1, 10-7 common 12-1 component 12-1 sheet 10-2, 10-12 data definition file (ddf) 20-1 data item identifiers mld file format 8-16 date format 7-23 date in title block option switch 6 B-10 ddf 20-1 example of 20-10 ddf file detail sketch entries 18-2 information note entries 18-3 default set add 5-15 copy 5-21 delete 5-20 revise 5-18 define default sets 5-11, 5-13 end point 5-80 lagging 5-81 project options 5-11, 5-21 delete existing files 5-23 solid line 5-81 spindle point 5-81 start point 5-80 tap points 5-81

Index IN - 7

define (continued) tracing 5-81 weld prefix 7-47 defining components as no MTO 7-77 continuation notes 7-71 dotted symbology 7-75 fabrication categories 7-78 isogen symbol keys 7-84 line ID 7-59 movable text 7-82 secondary orientation notes 7-74 start point notes 7-69 type 1 labels 7-61 type 2 labels 7-64 type 3 labels 7-67 defining general item notes 7-85 − 7-86 defining secondary or alternate indices for the MDL 7-87 definition file material list 7-44 delete 5-82 default set 5-20 drawing 5-11, 5-46 drawing records with undefined iso type 5-85 existing files 5-23, 5-91 descriptions material list option switch B-18 design file data in idf order 6-22 raw 6-12 sorted by coordinate 6-13 sorted by topo 6-15 interface error messages A-31 detail sketch option switch 71 B-28 detail sketch entries in the ddf 18-2 related information 18-2 detail sketch facility 18-1 cell library 7-43 details save 5-92 detail_sketch_facility 7-48 detail_sketch_facility table example of 7-49 determining sheet split points 15-4 determining the traversal start point 15-4 dimension overall

dimension (continued) overall (continued) option switch 118 B-40 round-off carry-over option switch 117 B-40 tapped branch option switch 121 B-40 units option switch 41 B-22 dimension standout character size option switch 4 B-9 line distance option switch 8 B-11 dimension/elevation vertical option switch 119 B-40 dimensioning control option switch 81 B-35 features 17-1 including gaskets 17-2 non-dimensioned supports 7-98 output 17-1 string 17-2 suppressing branch 17-2 usa style 17-3 valve centerline 17-2 dimensioning features related information 17-1 dimensions 5-75 on drawing option switch 9 B-12 disconnected sections 6-14 display elevation at bend/elbow intersections 17-3 at branch intersections 17-4 elsplit point coordinates 17-4 document purpose xiii dotted nozzle option switch 111 B-39 dotted symbology defining 7-75 dotted weld symbols 16-2 dotted_symbology_code_list_values 7-75 example assigning dotted symbology 7-75 DR symbol key B-47 drawing area option switch 35 B-20 dimensions on

IN - 8


drawing (continued) dimensions on (continued) option switch 9 B-12 margin option switch 10-13 B-13 multiple revise 5-42 number 5-30, 5-40 high 5-37, 5-50, 5-94, 5-107 low 5-37, 5-50, 5-94, 5-107 pipe support information option switch 64 B-26 plot 3-14 records delete 5-85 revise 5-38 size option switch 14-16 B-13 split control option switch 38 B-20 stacking arrangement option switch 36-37 B-20 symbology 5-71 drawing definition file 7-44 example of 20-10 drawing_data_table 10-7 dwg file example of C-64 E EBSC symbol key B-51 EDG 5-92 edit iso symbol 5-71 elbow tapped 13-3 elbows plotted leg lengths option switch 95 B-36 symbol keys B-51 ELBW symbol key B-51 ELCP symbol key B-51 elevation at bend/elbow intersections display 17-3 at branch intersections display 17-4 ELSC symbol key B-51 ELSW symbol key B-51 embedded attributes 7-10, 7-20 enclosure shape material part number 76 B-33 end point 5-76

end (continued) prep high 13-1, 13-5 low 13-1, 13-5 end connections, other symbol keys B-50 end coordinates suppress output option switch 5 B-10 end point define 5-80 end prep connections symbol keys B-43 end-point components extraction conventions 3-19 end_point_component_labels 7-70 END_POINT_COMPONENT_LABELS example defining continuation notes 7-71 EPBW symbol key B-58 EPFL symbol key B-58 err file example of C-54 error messages A-3, A-15 error log file example of C-54 error messages batch extraction software A-32 design file interface A-31 message file A-22 ESBW symbol key B-58 ESFL symbol key B-58 ETBW symbol key B-51 ETCP symbol key B-51 ETSC symbol key B-51 ETSW symbol key B-51 EUBW symbol key B-51 EX** symbol key B-45 example ddf 20-10 drawing definition file 20-10 examples HITS report 6-2 iso extraction documents C-3 EXBW symbol key B-58 EXFL symbol key B-59 exit iso symbol editor 5-82 export variables 5-3 ISO_ASCII_LOAD 5-4 ISOBATCH 5-4 ISOBATCHQUE 5-4

Index IN - 9

export variables (continued) ISOBORDER 5-4 ISOOPTION 5-3 ISOPATH 5-3 ISOPLOT 5-4 ISOREPORT 5-4 ISOSEED 5-4 PDISOFONT 5-5 SYMLIB 5-5 SYMNDX 5-5 extend witness line 17-3 extension stems 7-20 extraction by line ID 3-11 name substring 3-10 conventions 3-19 end-point components 3-19 implied materials at line name changes 3-20 olet type branches 3-19 pipe supports 3-20 type 63 data 3-20 creating seed files 9-1 criteria 3-9 date 5-31, 5-41 limitations 3-20 branch nesting 3-20 flanged pipe 3-21 system isometric 3-21 tapped piping components 3-21 number 5-31, 5-40 seed files 5-3 extraction information in the project database 15-3 extraction information in the database 15-3 EZBW symbol key B-58 EZFL symbol key B-59 F FA** symbol key B-47 fabricated bends (pulled) style for output 8-13 fabrication categories defining 7-78 fabrication category 7-78 falling lines option switch 19 B-14 FI** symbol key B-47 field fit weld allowance option switch 22 B-15

file data return option switch 109 B-39 material control pipeline reference format option switch 113 B-39 tables of intermediate records B-3 filenames long 5-23 files batch data 5-1 structure 7-2 files table 7-42 bending parameters file 7-44 center of gravity weight library 7-43 detail sketch facility cell library 7-43 drawing definition file 7-44 format file 7-44 ISOGEN user-defined symbol library 7-42 label description library 7-42 material list definition file 7-44 mto neutral file map 7-43 notes table 7-43 title block 7-43 valve operator symbol map 7-42 welds definition 7-44 filling in the title block (stib.exe) 4-6 filters in-line symbol keys B-47 fit symbol 5-80 fitting records spool and in-line B-6 fittings special 20-6 undimensioned branches 20-7 fittings with attached olets 13-4 flange loose allowance option switch 22 B-15 flanged pipe breaks in 7-41 extraction limitation 3-21 flanges symbol keys B-44 flanges LJSE symbol keys B-44 FLBL symbol key B-44 FLFL symbol key B-44 FLLB symbol key B-44

IN - 10


floor stands 7-20 flow arrow option switch 17 B-14 arrow size option switch 112 B-39 flow arrows 5-75 FLOW symbol key B-46 FLRC symbol key B-44 FLRE symbol key B-44 FLRG symbol key B-44 FLSE symbol key B-44 FLSJ symbol key B-44 FLSO symbol key B-44 FLSW symbol key B-44 FLWN symbol key B-44 FO** symbol key B-47 fonts on the isometric export variable 5-5 format file 7-44 forms conventions 2-5 FOSO symbol key B-44 FOWN symbol key B-44 FPFL symbol key B-54 FPPL symbol key B-54 FR** symbol key B-47 frame control option switch 18 B-14 frameworks isousrrefdim variable 5-5 frameworks reference file generate 5-86 FT** symbol key B-45 FX** symbol key B-45 G gadgets conventions 2-5 gapping hatching patterns option switch 102 B-38 general note 7-48 general note items defining 7-85 − 7-86 generate frameworks reference file 5-86 optional format for length output 8-10 pdme data 5-102 revised format for cut list 8-11 sheet numbers

generate (continued) sheet numbers (continued) using spool number prefix 7-51 spool numbers using spool number prefix 7-51 user-defined weld from code list 7-46 generated item table 12-2 generated_items 12-2, 12-9 generating title block input (tblock) 4-6 genitm_note_format 7-85 example defining general item notes 7-85 GENITM_NOTE_FORMAT example defining general item notes 7-86 gravity weight output center 82 B-36 H h file example of C-28 H3** symbol key B-49 H4** symbol key B-49 HA** symbol key B-49 hangar/support symbol key B-46 hatching gapping, patterns option switch 102 B-38 skew triangle option switch 101 B-37 HCSC symbol key B-55 HCSW symbol key B-55 header topo 6-23 HITS 1-4 report 6-1, 6-26 branch 6-12 cp # 6-12 direct 6-12 flags 6-12 name 6-12 node 6-12 occ 6-12 sect 6-12 section 1 basic input data and raw design file data 6-12 section 2 design file data sorted by coordinate 6-13 section 3 tracing data 6-14 section 4

Index IN - 11

HITS (continued) report (continued) section 4 (continued) design file data sorted by topo 6-15 section 5 design file data in idf order 6-22 sg_occ 6-12 topo 6-12 x 6-12 y 6-12 z 6-12 HITS report example of C-28 HV** symbol key B-48 I i file 9-4 IA** symbol key B-46 ic 7-70 identification instrument option switch 59 B-25 numbers record B-6 idf 1-4 idf file example of C-37 IDFL symbol key B-47 IDPL symbol key B-46 ie 7-70 II** symbol key B-46 implied item table 12-2 materials 7-11 implied materials at line name changes extraction conventions 3-20 implied_items 12-2, 12-6 extracting inspection numbers 12-9 in 7-70 increment revision number 5-92, 10-9 information messages A-5 information note 7-48 entries in the ddf 18-3 related information 18-2 information note facility 18-1 ingr_atext_specifications 7-58 initial setup considerations 5-3 in-line filters symbol keys B-47 input data 6-12 inspection number enclosure type 7-15

inspection isometric numbers 7-15 inspection number extracting 12-6, 12-9 inspection numbers unassigned default text 7-58 instrument balloon option switch 123 B-41 identification option switch 59 B-25 symbol keys B-46 instrument bubble 7-10 instruments symbol keys B-47 insulation control option switch 61 B-25 interactive isometric extraction 1-3, 3-1 ASCII to binary conversion 1-4 conventions and limitations 3-19 iso design file 3-12 ISOGEN 1-4 ISOGEN interface 1-3 isometric seed file 3-6 model files 3-9 options file 3-6 pipeline names 3-10 interface ISOGEN A-4, 1-3 job creation (jobctl.exe) 4-4 interface error log example of C-54 intergraph option switches 7-1 intergraph_options_block 7-6 intermediate data file 1-4 example of C-37 interpreting the HITS report 6-1 basic input data 6-12 design file data in idf order 6-22 sorted by coordinate 6-13 sorted by topo 6-15 example HITS report 6-2 raw design file data 6-12 to solve problems 6-26 tracing data 6-14 introduction 1-1 invalid lines 5-60, 5-63, 5-65 investigating batch extraction problems 4-7 IO** symbol key B-46

IN - 12


iplot 9-3 plot request files 9-3 IR** symbol key B-46 ISAM center of gravity weight library 19-2 iso area revise 5-25 design file 3-12 dgn name 5-30, 5-40 filenames 5-23 type drawing requirements 5-85 isoa_bgen 1-4 ISO_ASCII_LOAD 5-4 ISOBATCH 5-4 ISOBATCHQUE 5-4 ISOBORDER 5-4 isoc.def file example of C-4 isoc.note file 11-2 ISOGEN 1-4 Alias tables B-3 component versus sheet number file example of C-62 cut pipe report example of C-63 export variables 5-3 interface A-4, 1-3, 4-5 (izod2) splitting the mto neutral file (msplit) 4-6 (izod2.exe) 4-5 message file example of C-59 message file errors A-22 printed parts file C-60 record number 13-1 − 13-2 skey dimensions E-3 symbol name 13-1 user-defined symbol library 7-42 ISOGEN symbol keys defining 7-84 ISOGEN_options_block 7-4 isometric drawing plot 3-14 extraction 1-3, 3-1 presentation 20-1 seed file 3-6 creating 9-1 symbol editor 5-71 defining export variables 5-5 type option switch 21 B-15 types 20-12

isometric drawing area AText B-75 isometric weight and the STIB data file 19-1 spool 19-1 total 19-1 ISOOPTION 5-3 ISOPATH 5-3 ISOPLOT 5-4 ISOREPORT 5-4 ISOSEED 5-4 ISOUSRREFDIM 5-5 item name 13-1 ITFL symbol key B-55 izod2.exe 4-5 J job log file 4-7, 5-101 job creation 4-4 jobctl.exe 4-4 justification markers mld file format 8-16 K KABW symbol key B-53 KACP symbol key B-53 KASC symbol key B-53 KASW symbol key B-53 L label description library 3-9, 7-9 label description library 7-42 label library label definitions example of C-9 labels type 1 7-60 type 2 7-63 type 3 7-66 LABW symbol key B-55 lagging 5-76 define 5-81 lap joint 13-3 LASC symbol key B-55 last MTO date 5-31, 5-41 LASW symbol key B-55 layer names 20-8 L@BW symbol key B-52 lengths plotted leg elbows and tees option switch 95 B-36

Index IN - 13

limit indication sloping pipeline B-14 line 2 5-30, 5-39 3 5-30, 5-39 dimension standout distance option switch 8 B-11 falling option switch 19 B-14 feed 7-62 ID 7-13, 7-59 identification 3-10 selection by line ID 5-96 spacing material list option switch B-19 line ID defining 7-59 line name changes using implied materials 3-20 line names select 3-3 line summary AText B-84 line_id_definition 7-59 LINE_ID_DEFINITION example defining line ID 7-59 list cutting option switch 2 B-9 drawings 5-11, 5-54 material descriptions option switch 26 B-18 item code length option switch 28 B-19 line spacing option switch 29 B-19 output option switch 30 B-19 position option switch 25 B-17 reserved area option switch 35 B-20 text size option switch 27 B-18 type/length units option switch 24 B-17 material accumulation option switch 74 B-30 plotted material control option switch 23 B-16

load by area 5-59 − 5-60 by line 5-59, 5-64 by model 5-59, 5-62 log file job 4-7, 5-101 system 5-100 long iso filenames 5-23 loose flange allowance option switch 22 B-15 M M3** symbol key B-48 M4** symbol key B-48 MA** symbol key B-48 making a run log entry (pdsidf) 4-7 mapping attributes to the title block 10-1 drawing_data_table 10-7 segment_data_table 10-3 sheet_data_table 10-12 margin drawing option switch 10-13 B-13 mark cut option switch 3 B-9 material control file bolt diameter option switch 65 B-26 length option switch 65 B-26 pipeline reference format option switch 113 B-39 list accumulation drawing option switch 74 B-30 descriptions option switch 26 B-18 item code length option switch 28 B-19 line spacing option switch 29 B-19 output option switch 30 B-19 position option switch 25 B-17 printed length control option switch 63 B-26 reserved area option switch 35 B-20 text size option switch 27 B-18 type/length units option switch 24 B-17

IN - 14


material control file 8-1 list of available items 8-8 user-defined 8-7 material descriptions library 3-9 material Dlist definition file 8-6 material list control, plotted option switch B-16 definition file 7-44 output style 8-13 style 3 8-17 types of mld 8-2 welds in 8-13 material list definition contents of 8-14 material list, printed AText B-85 message file example of C-59 messages error A-3, A-15 file 7-6 information A-5 warning A-3, A-8 MIBW symbol key B-52 MIFL symbol key B-51 miscellaneous symbol keys B-46 miscellaneous items 20-8 mld file content 8-14 file format data item identifiers 8-16 justification markers 8-16 style 1 material list 8-3 style 2 material list 8-3 style 3 material list 8-3 mld file 8-6 format 8-15 style 2 8-2 style 3 8-3 style1 8-2 types of material list 8-2 mlt control 5-32, 5-40, 5-44 model files 3-9 number isometric 3-12 revised date 5-31, 5-40, 5-44 high 5-37, 5-51 low 5-37, 5-51

model (continued) status 5-31, 5-39, 5-43 code 5-37 status code 5-50, 5-94, 5-107 model numbers reset 3-3 select 3-2 modify text 7-56 for eccentric reducers 7-56 movable text defining 7-82 movable_text 7-81, 10-12 MOVABLE_TEXT example defining movable text 7-82 msg file example of C-59 msplit 4-6 MTBW symbol key B-52 MTFL symbol key B-52 MTO date 5-31, 5-41 neutral file 5-91 example of C-57 record map 12-1 neutral file record map center of gravity 19-2 common_record_data 12-2 component_attributes 12-4 generated_items 12-9 implied_items 12-6 user-defined 8-1 material list 8-2 material list definition file 8-6 offshore material category 8-9 operating requirements 8-4 mto neutral file map 7-43 multiple drawings revise 5-42 MV** symbol key B-48 N NBSC symbol key B-53 NC** symbol key B-45 network problems 6-14 traversal 1-4 neutral file map mto 7-43 new skey 5-74

Index IN - 15

new_symbol_keys 7-84 example defining isogen symbol keys 7-84 NIPL symbol key B-55 NISC symbol key B-55 node text 10-2 no-mto 7-16, 7-70 nomto_code_list_values 7-77 example defining components as no MTO 7-77 non-dimensioned supports 7-98 nongraphic outputs 1-4 note general 7-48 specific 7-48 notes table 7-43, 10-1, 10-7 creating 11-1 nozzle dotted option switch 111 B-39 nozzle connection note 7-13 nozzle_note 7-72 NRSC symbol key B-53 number connect points 13-1, 13-3 sections 5-30, 5-39, 5-43 spool option switch 39 B-21 tag option switch 60 B-25 weld option switch 53 B-24 number of segments symbol keys B-43 O occurrence numbers 6-12 off-line instruments 7-16 offset angle tolerance option switch 115 B-39 dimension tolerance option switch 116 B-39 offshore fabrication category 16-4 offshore material category 8-9 offshore_fabcat_code_list_values 7-80 old skey 5-73 olet type branches extraction conventions 3-19 o’lets symbol keys B-55

olets attached to fittings 13-4 OP symbol key B-47 operating requirements user-defined BOM 8-4 operators symbol keys B-62 option record 4-3 option switches B-8 automatic split points in pipe 108 B-38 bolting lengths in material control file 65 B-26 center of gravity weight output 82 B-36 character size 4 B-9 coordinate output control 66 B-27 coordinates at tapping points 122 B-41 cut marks 3 B-9 cutting list 2 B-9 data return file 109 B-39 date in title block 6 B-10 detail sketch 71 B-28 dimension line standout distance 8 B-11 dimension round-off carry-over 117 B-40 dimensional units 41 B-22 dimensioning control 81 B-35 dimensions on drawings 9 B-12 dotted nozzle 111 B-39 drawing area 35 B-20 drawing margin 10-13 B-13 drawing size 14-16 B-13 drawing split control 38 B-20 drawing stacking arrangement 36-37 B-20 falling lines 19 B-14 field fit weld allowance 22 B-15 flow arrow 17 B-14 flow arrow size 112 B-39 frame control 18 B-14 gapping hatching patterns 102 B-38 instrument balloon 123 B-41 instrument identification 59 B-25 insulation control 61 B-25 intergraph 7-1 isometric type 21 B-15 loose flange allowance 22 B-15 material list accumulation 74 B-30 material list descriptions 26 B-18 material list item code length 28 B-19 material list line spacing 29 B-19 material list output 30 B-19 material list position 25 B-17 material list reserved area 35 B-20 material list text size 27 B-18 material list type/length units 24 B-17

IN - 16


option switches (continued) material part number enclosure shape 76 B-33 offset angle tolerance 115 B-39 offset dimension tolerance 116 B-39 overall dimension 118 B-40 part number box 73 B-29 picture scale 34 B-19 pipe support information on drawing 64 B-26 pipe supports 40 B-21 pipeline reference format in material control file 113 B-39 plotted leg lengths elbows and tees 95 B-36 plotted material list control 23 B-16 printed material list length control 63 B-26 sketch detail units 92 B-36 skew box dimension standout, triangles 100 B-37 skew box style and dimensioning 99 B-37 skew box/triangle type 97 B-37 skew triangle hatching 101 B-37 skews, 3D drawn as 2D 67 B-28 sloping pipeline indication limit B-14 spare 103-107 B-38 spare 110 B-39 spare 124-126 B-42 spare 52 B-24 spare 56-57 B-25 spare 69 B-28 spare 72 B-28 spare 78-79 B-34 spare 83-91 B-36 spare 93-94 B-36 spare 96 B-37 spare 98 B-37 specification breaks 114 B-39 spool numbers 39 B-21 suppress output of end coordinates 5 B-10 suppress skew boxes/triangles on branch legs 70 B-28 tag number 60 B-25 tapped branch dimension 121 B-40 tapped branch scale 120 B-40 test parameter block 127-140 B-42 title block position 25 B-17 tracing control 62 B-26 valve centerline dimensioning 80 B-34 vertical dimension/elevation 119 B-40 view point 42 B-23

option switches (continued) weld control 54 B-25 weld number 53 B-24 weld number allocation at reinforcement pads 77 B-34 weld number allocation at slip-on flanges 77 B-34 zero length bends 68 B-28 optional format for length output 8-10 options file 1-4, 3-6, 7-1 alternate_description_index 7-87 atext_specifications 7-56 dotted_symbology_code_list_values 7-75 end_point_component_labels 7-70 example of C-4 export variable 5-3 file structure 7-2 files table 7-42 genitm_note_format 7-85 ingr_atext_specifications 7-58 intergraph_options_block 7-6 ISOGEN_options_block 7-4 line_id_definition 7-59 movable_text 7-81 new_symbol_keys 7-84 nomto_code_list_values 7-77 nozzle_note 7-72 pipeline_header 7-50 secondary_orientation_note 7-74 shop_fabcat_code_list_values 7-78 start_point_notes 7-68 type_1_labels 7-60 type_2_labels 7-63 type_3_labels 7-66 options_block 7-6 order of table entries 13-5 orientation 5-75 OTBW symbol key B-58 OTFL symbol key B-59 OTSC symbol key B-58 output center gravity weight 82 B-36 control, coordinate option switch 66 B-27 output file export variable 5-4 overall dimension option switch 118 B-40 overlap 6-26 P part number box control

Index IN - 17

part number (continued) box control (continued) option switch 73 B-29 material enclosure shape 76 B-33 parts file example of C-60 parts list 7-6 paterns gapping hatching option switch 102 B-38 PB+D symbol key B-52 pc 7-70 PDISOFONT 5-5 pdisoplot 4-7 pdme data generate 5-102 PDS item name 13-1 operator name 13-1 to-ISOGEN symbol map 7-12 valve operator name 13-4 PDS environment 2-1 PD_Shell 2-2 PD_Shell 2-2 form conventions 2-5 pdshell environment 2-1 PDSidf 4-7 pdsidf 4-7 PDS-to-ISOGEN symbol map 13-1 end prep low and end prep high 13-5 ISOGEN record number 13-2 symbol name 13-1 number of connect points 13-3 order of table entries 13-5 PDS item name 13-1 valve operator name 13-4 tapped component name 13-3 record number 13-4 picture scale option switch 34 B-19 pipe support information on drawing option switch 64 B-26 supports option switch 40 B-21 pipe components symbol keys B-45

pipe report cut C-63 pipe supports 5-79, 7-14 extraction conventions 3-20 pipeline attributes dotted 20-4 special 20-4 sloping indication limit B-14 pipeline names 3-10 extraction line ID 3-11 name substring 3-10 pipeline reference format material control file option switch 113 B-39 pipeline_header 7-50 PIPELINE_HEADER example breaking supply responsibility along a pipeline 7-53 − 7-54 changing construction responsibility along a pipeline 7-53 pipes, fixed length symbol keys B-54 PL symbol key B-45 plate orifice and restrictor symbol keys B-47 plot isometric drawing 3-14 plot copies 5-102 plot file export variable 5-4 plot request files creating 9-3 iplot 9-3 plotted leg lengths elbows and tees option switch 95 B-36 plotted material AText B-80 plotted material list control option switch 23 B-16 plotting 4-7, 5-92 pn 7-70 point control view option switch 42 B-23 points coordinates at tapping option switch 122 B-41

IN - 18


position title block 8-14 option switch 25 B-17 PR symbol key B-47 prefix 7-70 presentation 20-1 bend/elbow representation 20-5 example ddf 20-10 fittings special 20-6 undimensioned branches 20-7 isometric related information 20-2 layer names 20-8 miscellaneous items 20-8 pipeline attributes dotted 20-4 special 20-4 program defaults 20-9 previous details save 5-92 primary model number 3-9 printed material list length control option switch 63 B-26 printed parts file example of C-60 printed parts list 7-6 process queue export variable 5-4 program defaults 20-9 project database and extraction information 15-3 project options defining 5-21 delete existing files 5-23 prt file example of C-60 pseudo attribute 7-52 pt 7-70 Q queue export variable 5-4 queue_descript file 3-14, 5-102 R RA** symbol key B-47 raw design file data 6-12

RBSC symbol key B-58 RBSW symbol key B-58 RCBW symbol key B-57 RCCP symbol key B-57 RCFL symbol key B-57 RCSC symbol key B-57 RD symbol key B-49 RDB data 3-9 REBW symbol key B-58 record ID numbers B-3, B-6 spool and in-line fitting B-6 table of intermediate B-3 record number 13-2 tapped component 13-4 reducers symbol keys B-57 re-extract existing sheets 5-102 re-extraction and the project database 15-3 REFL symbol key B-58 reinforcing pads 7-17 repeatability 5-102, 15-1 and the project database 15-3 related information 15-1 rules for 15-2 report file export variable 5-4 reports 5-12, 5-104 center of gravity 19-2 cut pipe 7-6 RESC symbol key B-58 reset model numbers 3-3 revise default set 5-18 drawing 5-11, 5-33 iso area 5-11, 5-25 multiple drawings 5-42 single drawing 5-38 revision block 5-32, 5-41, 5-44 number 5-32, 5-40, 5-44 incrementing 5-92 RFPL symbol key B-59 RNSC symbol key B-57 round-off dimension option switch 117 B-40 RP symbol key B-45 RV** symbol key B-49 S S3** symbol key B-48

Index IN - 19

S4** symbol key B-48 SA** symbol key B-48 save previous details 5-92 SB symbol key B-46 SC symbol key B-50 scale picture option switch 34 B-19 tapped branch option switch 120 B-40 scale factor 5-75 schedule batch job 5-12, 5-100 secondary indices for the MDL defining 7-87 secondary_orientation_note 7-74 example defining secondary orientation notes 7-74 sed file example of C-62 seed file export variable 5-4 seed files creating for extraction 9-1 isometric 9-1 seg file example of C-64 segment data table 7-43 summary table 10-3 segment_data_table 10-3 select line names 3-3 lines for extraction by line ID 5-96 model numbers 3-2 setup considerations 5-3 SG** symbol key B-45 sheet data table 10-2, 10-12 generated 5-32, 5-41 number 10-12 sheet numbers:generating with spool number prefix 7-51 sheet splits correcting incorrect 15-5 determining 15-4 sheet_data_table 10-12 shop_fabcat_code_list_values 7-78 SHOP_FABCAT_CODE_LIST_VALUES example

SHOP_FABCAT_CODE_LIST_VALUES (continued) example (continued) defining fabrication categories 7-78 single drawing revise 5-38 size drawing option switch 14-16 B-13 flow arrow option switch 112 B-39 sketch detail option switch 71 B-28 sketch detail units option switch 92 B-36 skew 3D drawn as 2D with fall indication option switch 67 B-28 box dimension standout, triangles option switch 100 B-37 box style and dimensioning option switch 99 B-37 box/triangle type option switch 96 B-37 suppress boxes/triangles on branch legs option switch 70 B-28 triangle hatching option switch 101 B-37 skey new 5-74 old 5-73 skey dimensions E-3 SKEY, symbol keys B-43 SKSW symbol key B-55 solid line define 5-81 sort groups 8-9 SP symbol key B-45 spare option switch 69 B-28 option switch 72 B-28 spare option switch 56-57 B-25 spare option switch 103-107 B-38 spare option switch 110 B-39 spare option switch 124-126 B-42 spare option switch 52 B-24 spare option switch 78-79 B-34 spare option switch 83-91 B-36 spare option switch 93-94 B-36

IN - 20


spare option switch 96 B-37 spare option switch 98 B-37 specialty and descriptions library 3-9 specific note 7-48 specification breaks option switch 114 B-39 specification changes AText B-79 spindle key 5-75 point 5-76 spindle point define 5-81 split control drawing option switch 38 B-20 split point coordinates display 17-4 split points automatic in pipe option switch 108 B-38 splitting the mto neutral file (msplit) 4-6 spool number option switch 39 B-21 spool and in-line fitting records B-6 spool number prefix 7-51 generating sheet numbers 7-51 generating spool numbers 7-51 spool numbers generating with spool number prefix 7-51 SR symbol key B-45 stacking arrangement drawing option switch 36-37 B-20 standard material list 8-2 user-defined variation of 8-2 standard note 180 & 1100 codelist values for 16-3 start point 5-76 defining 5-80 start_point_notes 7-68 Start_Point_Notes example defining start point notes 7-69 stib.exe 4-6 string dimensioning 17-2 structural column reference 7-37 style fabricated (pulled) bends) output 8-13 material list output 8-13

style 1 material list contents and changes for 8-3 style 2 material list contents and changes for 8-3 mld file 8-2 user-defined material list example 8-19 style 3 data item info 8-18 material list 8-17 basic control info 8-17 contents and changes for 8-3 mld file 8-3 user-defined material list example 8-19 style1 mld file 8-2 submit batch job 5-100 for plotting 5-92 summary block 10-3 supports pipe option switch 40 B-21 suppress output of end coordinates option switch 5 B-10 suppress skew boxes/triangles on branch legs option switch 70 B-28 SV** symbol key B-48 SW symbol key B-50 SWBW symbol key B-55 switches option B-8 automatic split points in pipe 108 B-38 bolting diameters in material control file 65 B-26 center of gravity weight output 82 B-36 character size 4 B-9 coordinate output control 66 B-27 coordinates at tapping points 122 B-41 cut marks 3 B-9 cutting list 2 B-9 data return file 109 B-39 date in title block 6 B-10 dimension line standout distance 8 B-11 dimension round-off carry-over 117 B-40

Index IN - 21

switches (continued) option (continued) dimensional units 41 B-22 dimensioning control 81 B-35 dimensions on drawings 9 B-12 dotted nozzle 111 B-39 drawing area 35 B-20 drawing margin 10-13 B-13 drawing size 14-16 B-13 drawing split control 38 B-20 drawing stacking arrangement 36-37 B-20 falling lines 19 B-14 field fit weld allowance 22 B-15 flow arrow 17 B-14 flow arrow size 112 B-39 frame control 18 B-14 gapping hatching patterns 102 B-38 instrument balloon 123 B-41 instrument identification 59 B-25 insulation control 61 B-25 isometric type 21 B-15 loose flange allowance 22 B-15 material list accumulation 74 B-30 material list descriptions 26 B-18 material list item code length 28 B-19 material list line spacing 29 B-19 material list output 30 B-19 material list position 25 B-17 material list reserved area 35 B-20 material list text size 27 B-18 material list type/length units 24 B-17 material part number enclosure shape 76 B-33 offset angle tolerance 115 B-39 offset dimension tolerance 116 B-39 overall dimension 118 B-40 part number box 73 B-29 picture scale 34 B-19 pipe support information on drawing 64 B-26 pipe supports 40 B-21 pipeline reference format in material control file 113 B-39 plotted leg lengths elbows and tees 95 B-36 plotted material list control 23 B-16 printed material list length control 63 B-26 sketch detail units 92 B-36 skew box dimension standout, triangles 100 B-37

switches (continued) option (continued) skew box style and dimensioning 99 B-37 skew box/triangle type 97 B-37 skew triangle hatching 101 B-37 skews, 3D drawn as 2D 67 B-28 sloping pipeline indication limit B-14 spare 103-107 B-38 spare 110 B-39 spare 124-126 B-42 spare 52 B-24 spare 56-57 B-25 spare 78-79 B-34 spare 83-91 B-36 spare 93-94 B-36 spare 96 B-37 spare 98 B-37 specification breaks 114 B-39 spool number 39 B-21 suppress output of end coordinates 5 B-10 tag number 60 B-25 tapped branch dimension 121 B-40 tapped branch scale 120 B-40 test parameter block 127-140 B-42 title block position 25 B-17 tracing control 62 B-26 valve centerline dimensioning 80 B-34 vertical dimension/elevation 119 B-40 view point 42 B-23 weld control 54 B-25 weld number 53 B-24 weld number allocation at reinforcement pads 77 B-34 weld number allocation at slip-on flanges 77 B-34 weld number box 75 B-31 zero length bends 68 B-28 option 69 spare B-28 option 70 suppress skew boxes/triangles on branch legs B-28 option 71 detail sketch B-28 option 72 spare B-28 symbol 5-76 definition software 5-71 design export variable 5-5 index

IN - 22


symbol (continued) index (continued) export variable 5-5 library export variable 5-5 user-defined 7-42 map 13-1 name 13-1 origin 5-74, 5-76 symbol editor use of 5-71 symbol keys, SKEY B-43 bend radius B-43 bends B-51 caps B-53 couplings B-53 crosses B-54 elbows B-51 end connections, other B-50 end prep connections B-43 flanges B-44 flanges LJSE type B-44 in-line filters B-47 instruments B-46 − B-47 miscellaneous items B-46 number of segments B-43 o’lets B-55 operators B-62 pipe components miscellaneous B-45 pipes, fixed length B-54 reducers B-57 skey connect points B-43 tees B-56 traps B-49 unions B-59 valves B-59 four-way B-61 three-way B-61 vent B-49 welds B-50 SYMDGN 5-5 SYMLIB 5-5 SYMNDX 5-5 system isometrics extraction limitations 3-21 log file 5-100 − 5-101 T TA** symbol key B-49 table entries order 13-5 files title block 10-1 intermediate file records B-3

table (continued) notes 10-1 tag number option switch 60 B-25 tag numbers 7-10 tap name 13-1 points 5-76 record number 13-1 tap points coordinates at option switch 122 B-41 define 5-81 tapped component name 13-3 olets attached to fittings 13-4 tapped elbows 13-3 component record number 13-4 elbows 13-3 piping components 3-21 tapped branch dimension option switch 121 B-40 scale option switch 120 B-40 taps 5-77 TB+D symbol key B-52 tblock 4-6 T@BW symbol key B-52 TEBW symbol key B-56 TECP symbol key B-56 tee symbol keys B-56 tees plotted leg lengths option switch 95 B-36 TEFL symbol key B-56 TERF symbol key B-56 TESO symbol key B-56 test parameter block option switch 127-140 B-42 TESW symbol key B-56 text alternative B-64 dimension standout option switch 4 B-9 size material list option switch 27 B-18 text node number 10-2 restrictions on 10-2

Index IN - 23

text node number restrictions on 10-2 T@FLsymbol key B-52 THSC symbol key B-55 TI** symbol key B-49 title block AText B-79 data files 7-20 date in option switch 6 B-10 mapping attributes 10-1 mapping file 10-4 position option switch 25 B-17 positioning 8-14 summary table 10-3 table files 10-1 tables file 7-43 title block table example of C-64 TO** symbol key B-49 tolerance 7-9 offset angle option switch 115 B-39 offset dimension option switch 116 B-39 topo design file data sorted by 6-15 header 6-23 total isometric weight 19-1 TR** symbol key B-49 tracing 5-76 control option switch 62 B-26 data 6-14 define 5-81 trailing zeros eliminating from isometric 10-4 transfer components between sort groups 8-9 trap symbol keys B-49 traversal start point determining 15-4 traversing a network 6-22, 6-24 − 6-25 triangle hatching skew option switch 101 B-37 skew type option switch 96 B-37 triangles skewed box dimension standout

triangles (continued) skewed box dimension standout (continued) option switch 100 B-37 TSBW symbol key B-56 TSCP symbol key B-56 TSFL symbol key B-56 TSSW symbol key B-56 TU** symbol key B-46 type 5-38, 5-43 isometric 20-12 option switch 21 B-15 type 63 data extraction conventions 3-20 type_1_labels 7-60 example defining type 1 labels 7-61 type_2_labels 7-63 TYPE_2_LABELS example defining type 2 labels 7-64 type_3_labels 7-66 TYPE_3_LABELS example defining type 3 labels 7-67 typefaces xv U uconfigure.dat file 5-6 unassigned inspection numbers default text 7-58 unions symbol keys B-59 unique weld numbering 16-4 units dimensional option switch 41 B-22 sketch detail option switch 92 B-36 UNSC symbol key B-59 UNSW symbol key B-59 update project database 4-7 usa style dimensioning 17-3 user-defined MTO 8-1 text and user-positioned text 8-3 variation of the standard material list 8-2

IN - 24


user-defined BOM 8-1 operating requirements 8-4 user-defined drawing symbology 5-71 creating a user-defined symbol library 5-83 using the newly-created symbol library 5-84 user-defined material control file 8-7 user-defined material list example of style 2 8-19 example of style 3 8-19 user-defined MTO related information 8-2 user-defined symbol library 7-42 user-defined weld prefix 16-4 user_defined_component_bom 7-95 user_defined_generated_item_bom 7-92 user_defined_implied_item_bom 7-89 user_defined_welds 7-45 generating 7-46 using HITS report to solve problems 6-26 newly-created symbol library 5-84 the isoc.note file 11-2 utilities 5-11, 5-56 bulk load lines 5-57 from ASCII file 5-67 delete drawing records 5-85 frameworks reference file 5-86 iso symbol editor 5-71 assemble iso symbol 5-76 V V3** symbol key B-61 V4** symbol key B-61 VALOPR table 7-42 valpor 7-18 valve centerline dimensioning 17-2 option switch 80 B-34 operator table 14-1 operators 7-11 valve operator symbol map 7-42 valves four-way symbol keys B-61 symbol keys B-59 three-way symbol keys B-61 variables 5-3 VB** symbol key B-60 VC** symbol key B-60

VD** symbol key B-60 vent symbol keys B-49 vertical dimension/elevation option switch 119 B-40 VG** symbol key B-60 view point control option switch 42 B-23 VK** symbol key B-60 VN** symbol key B-60 VP** symbol key B-60 VR** symbol key B-61 vrs sheet number file 7-6 VS** symbol key B-61 VT** symbol key B-60 VV** symbol key B-60 VX** symbol key B-60 VY** symbol key B-60 W warning messages A-3 warning messages A-8 wdf file example of 16-9 weight display 19-1 center of gravity 19-2 related information 19-1 weight library center of gravity 7-43 weld control option switch 54 B-25 enhancements related information 16-1 field fit allowance option switch 22 B-15 number option switch 53 B-24 symbol keys B-50 user-defined 7-45 weld box summary standard AText B-85 user-defined AText B-86 weld boxes alternative style 16-6 weld definition report format file example of 16-9 weld number allocation reinforement pads 77 B-34

Index IN - 25

weld number (continued) allocation (continued) slip-on flanges 77 B-34 box control option switch 75 B-31 weld summary report 16-5 weld_prefix 7-47 example define weld prefix 7-47 welds 7-13, 16-1 branch 12-9 dotted 16-2 in material list 8-13 listed in the bom 16-10 offshore fabrication category 16-4 unique weld numbering 16-4 user-defined weld prefix 16-4 wdf file example of 16-9 weld data item information 16-8 weld definition file format 16-5 weld summary report 16-5, 16-8 welds boxes using a backing sheet 16-6 welds definition 7-44 WF symbol key B-50 witness line extend 17-3 WM symbol key B-50 WMF symbol key B-50 WO symbol key B-50 WOF symbol key B-50 WS symbol key B-50 WTBW symbol key B-55 WW symbol key B-50 X XA** symbol key B-47 XV** symbol key B-49 Z zero length bends option switch 68 B-28 zero length leg 6-24 zeros eliminating trailing 10-4

IN - 26


Isometric Drawing Extraction

Recommend Documents