3-66
Chapter 3: Maintenance
11 Confirm that all three files as shown in Ta Tabl ble e 33-17 17 are are saved on the laptop in a distinct folder that has a name noting the OLED Graphics Version number. Table 3-17 Items that must be downloaded to Laptop and placed in the appropriate folder. Item
Purpose
File Name as Shown On Laptop
WMS OLED Graphics Installation Tool
Communicates with the OLED Button Panel
WMS_USBTestCommTool_Vx_xx_setup.exe
Button Panel Controller Board OLED Graphics
OLED Graphics for Button Panel Controller Board
btnpanelHT
Button OLED Graphics OLED Graphics Graphics for each individual button
OLEDBtn
12 Close the Supply Chain and Commercial Ops. Home Page.
Installing OLED Graphics from Laptop (if necessary)
The OLED Button Panel will probably ship with OLED Graphics installed. If necessary, however, this section describes the installation of the Button Panel Controller Board OLED Graphics and the Button Panel Module OLED Graphics from a laptop via a USB cable connection.
ESD: Observe ESD: Observe all appropriate safety and ESD precautions listed in Preventing ESD on page 1-5 i 1-5 i of Chapter 1.
Installing Controller Board OLED Graphics Complete the following steps to select, install, and verify the OLED Button Panel Controller Board OLED Graphics: 1 Ensure that the AC Line Cord is connected to the Power Entry Assembly to ensure proper grounding. 2 Connect the Button Panel to the Laptop using one of the following methods:
If you have an extra USB Cable, disconnect the existing USB connection to the Button Panel and connect the Button Panel to the laptop with the extra USB Cable. If you do not have an extra USB Cable, disconnect the OLED Button Panel USB Cable from the CPU, Figure 3-112 (A), 3-112 (A), remove it from the cable clamps, and connect it to the laptop.
Figure 3-112 USB Cable connected to CPU Enclosure (left) and version with USB Connector Cover Plate (right).
A
B
A
3 If you are installing the Button Panel onto a game with an Ethernet/USB Cover, Figur Fi gure e 3-1 3-112 12 (B), (B), reference the Technical Service Bulletin 16-020293-xx: CPU-NXT Enclosure Ethernet/USB Covers for the steps to access the USB Port. 4 Turn the game ON at the Power Switch in order to power the OLED Button Panel during the OLED Graphics installation. 5 On the laptop, open the WMS_USBTestCommToo WMS_USBTestCommTool_Vx_xx_setup.exe l_Vx_xx_setup.exe zip file that was downloaded earlier.
June 2010
Button Panel Maintenance
6 In the zip file window that displays, open WMS_USBTestCommTool_Vx_xx_setup.exe).
the
installation
file
3-67 (also
called
The Installation Wizard opens, Figure 3-113. Figure 3-113 Installation Wizard.
A
7 Complete the Installation Wizard sequence by hitting Next each time you are prompted, Figure 3-113 (A). 8 When the Installation Wizard sequence is completed, locate the file WMS USB Test Comm Tool on the Desktop folder of the laptop. The icon for this file is shown in Figure 3-114. Figure 3-114 WMS USB Test Comm Tool icon.
If you are unable to locate the WMS USB Test Comm Tool icon or file in the Desktop folder of the laptop, then the network settings of the laptop have caused the file to be saved in an alternate location. Search the hard drive of the laptop for the file name WMS USB Test Comm Tool to locate the file.
16-026146-00
3-68
Chapter 3: Maintenance
9 Start the WMS USB Test Comm Tool program and select Agree when prompted. The Main Test Program window displays, Figure 3-115. Figure 3-115 Main Test Program window.
June 2010
Button Panel Maintenance
3-69
10 Verify that the Product ID (hex) drop-down menu is set to 000b, Figure 3-115 (A), and select Connect, Figure 3-115 (B). Figure 3-116 Verify Product ID (hex) and select Connect.
A
16-026146-00
B
3-70
Chapter 3: Maintenance
11 View the Status field in the Main Test Program window and determine the following: If...
Then...
the two windows shown at Figure 3-117 display side by side, with "Connection index =3" shown as the last entry on the left window
the program connected successfully with the Button Panel. Proceed to step 12 on page 3-71.
"No devices detected" displays
the laptop is not communicating with the Button Panel and the USB or Power Cable is likely disconnected or damaged. Complete the following steps to find and address the error:
1 Check the connections of the 24V Power Cable and USB cable to the Button Panel PCB.
2 Check the connection of the USB cable to the CPU. 3 Check the entire length of the USB cable for damage. 4 Check the connection of the 24V Power Cable at J22 on the Bulkhead Board.
5 6 7 8 9
Check the entire length of the 24V Power Cable for damage. Replace the USB cable. Replace the 24V Power Cable. Replace the Button Panel, as the Button Panel PCB may be damaged. Try to connect to the Button Panel with another laptop.
Figure 3-117 Main Test Program window properly connected.
A
June 2010
Button Panel Maintenance
3-71
12 Select Firmware Download from the drop-down menu, even if that selection is already highlighted, Figure 3-117 (A). The Firmware Download window, Figure 3-118, displays. Figure 3-118 Firmware Download Window.
A
13 Select Download Controller Firmware, Figure 3-118 (A).
16-026146-00
3-72
Chapter 3: Maintenance
14 When prompted, select the file btnpanelHT that was downloaded earlier to the laptop and saved to an appropriate folder. The status is displayed in the yellow banner as the existing Button Panel Controller Board OLED Graphics are erased, Figure 3-119 (A), and the new OLED Graphics are installed. When the installation is complete, the banner turns green, Figure 3-119 (B). Figure 3-119 Firmware Download Window.
A
C
B
15 Once the Button Panel Control Board is installed, select Download Button Firmware (ALL Buttons), Figure 3-119 (C).
June 2010
Button Panel Maintenance
3-73
16 When prompted, select the file OLEDBtn that was downloaded earlier to the laptop and saved to an appropriate folder. The status is displayed in the yellow banner as the existing Button OLED Graphics are erased, Figure 3-120 (A), and the new OLED Graphics are installed. Figure 3-120 Firmware Download Window.
A
B
17 When the installation is complete, the banner turns green, Figure 3-120 (B), and the OLED Graphics versions are displayed for the controller and each button position. Verify that the version is correct for the controller and each button. 18 Close the WMS USB Test Comm Tool program. 19 Turn the game OFF at the Power Switch.
16-026146-00
