File to File (Xslt Mapping)

FILE TO FILE XSLT MAPPING.

Author:  Srinath Ravi Design Steps in Integration builer

Create source and target Data Type for your scenario. Follow these screen shots.

Source Data type

Target data Type

Creation of Message type for both the Data Types

Creation of Message Interface

" Step ow go to! Message obects and using I#ported $rchives! i#port your %slt Mapping. It should be in .&ip ' .ar file.

Author:  Srinath Ravi((((((((((((((((((((((((((((((((((((File to file)%slt* scenario page+ , -  XSLT Mapping !"#$l %ersion&'(.)' "* !#sl:trans+or$ %ersion&,(.), #$lns:#sl&,http:--./.org-(000-XSL-Trans+or$, #$lns:sap&,http:--.sap.1o$-sap#sl, #$lns:aash&,urn:Aash:#sltMapping, #$lns:ns)&,urn:Aash:#sltMapping,* !#sl:te$plate $at1h&,-,* !aash:MT2Stuent23esult* !Data* !Na$e* !#sl:%alue4o+ sele1t&,1on1at5ns):MT2Stuent-Data-FNa$e6ns):MT2Stuent-Data-LNa$e7,-* !-Na$e* !Mar8s* !Total2Mar8s* !#sl:%alue4o+ sele1t&,5ns):MT2Stuent-Data-Mar8s-Maths79 5ns):MT2Stuent-Data-Mar8s-S1ien1e7 ,-* !-Total2Mar8s* !-Mar8s* !-Data* !-aash:MT2Stuent23esult* !-#sl:te$plate* !-#sl:trans+or$*

 ow! create Interface #apping

 ow activate the Change /ist and you are done with design part. To test your 0S/T #apping! go to Test tab in Display Interface #apping and provide data to see the desired result. See below+

Clic1 on e%ecute to run this! inside baloon! chec1 the result shown.

on+iguration steps

 ow create a co##unication channel for your 2usiness syste# for receiver and sender. Sender channel

Receiver channel

Create sender agree#ent.

Create receiver agree#ent.

Create receiver deter#ination and also with the help of this step you will create Interface deter#ination.

Interface Deter#ination

 ow we are done with configuration part. $nd activate these to run your scenario. Input XML !"#$l %ersion&,(.), en1oing&,;TF4<,"* !ns):MT2Stuent #$lns:ns)&,urn:Aash:#sltMapping,* !Data* !FNa$e*Tho$as!-FNa$e* !LNa$e*=arghese!-LNa$e*

!Mar8s* !Maths*0>!-Maths* !S1ien1e*0/!-S1ien1e* !-Mar8s* !-Data* !-ns):MT2Stuent*

3ut your input file at target location that you have provided in Co##unication channel.  ow go to s%#b(#oni and loo1 for your #essage.

Output XML !"#$l %ersion&,(.), en1oing&,ut+4<, "* !aash:MT2Stuent23esult #$lns:aash&, urn+$ash+%sltMapping,* !Data* !Na$e* Tho#as 4arghese!-Na$e* !Mar8s* !Total2Mar8s* ,56!-Total2Mar8s* !-Mar8s* !-Data* !-aash:MT2Stuent23esult*