Instructions manual
EN
Electronic module
PCI07 62 205 827 15 ed00
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
CONTENTS
Chapter 1 - General description
2
Display language selection 1.1 - General 1) General description 2) Emergency stop, time-delayed stop 3) Analog sensors 4) Battery replacement
2 2 2 2 2 2
1.2 - Functions 1) Control 2) Data 3) Regulation 4) Control of condensate drain-off 5) Signalling of maintenance operations 6) Management of operating defects 7) Programmin compressor startup and stopping
2 2 2 2 2 2 2 2
1.3 - PCI front panel 1) LED indicators 2) Keys 3) Display
3 3 3 3
1.4 - PCI rear panel 1) Description of inputs/outputs
4 4
Schematics of PCI front and rear panels
1.5 - Definitions
Chapter 2 - Menus 2.1 - Initialisation Menu 2.2 - Programming Menu 2.3 - Machine status information menu 2.4 - Machine configuration information menu
Chapter 3 - Description of messages
5
6
7 7 8 9 10
11
3.1 - Setting of machine operating parameters - Language selection - Setting of maintenance cycles - Setting startup and drain - Setting the clock - Setting the regulation pressure - Setting regulation mode - Selection and setting of timers
11 11 11 11 11 12 12 12
3.2 - Compressor data
13
3.3 - Warnings
15
3.4 - Maintenance
16
3.5 - Faults
16
Chapter 4 - Options
18
4.1 - Serial cable 4.2 - Serial interface
Chapter 5 - Temperature protection test
18 18
19
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Chapter 1 - General description Selecting the language: Open the menu by pressing on F1 (pushbutton • at the rear of the PCI) Select the required language using key F3 • Exit the menu using key F1 •
1.1 - General 1) General description descripti on The PCI07 is a micro-processor-equipped electronic module used to start and stop the ROLLAIR ® , to manage ROLLAIR ® faults and alarms, generate information on the operating status, and control condensate drain-off and remote transmissions and remote control. The PCI07 executes the following functions in particular : Management of 2 analog inputs: a temperature probe probe and • a pressure sensor Programming of compressor start-up and shutdown • Control, fault reporting and and remote display of compressor • operating status (option) Automation of alternating operation between several • compressors (option) Timed On/Off management of a dryer (according to • parameters)
2) Emergency stop, time-delayed stop WARNING: All compressors fi tted with an electronic management board PCI07 must be provided with an emergency knock off push button which stops the compressor and the dryer. WARNING: The compressor shutdown time can be delayed by pressing the PCI07 O key, although there is a minimum of 30 seconds noload operation prior to full machine shutdown. The shutdown phase is indicated by the "STOPPING" and the green LED associated with the key.
3) Analog sensors The PCI07 manages 2 analogue measurement channels to measure the service pressure (machine outlet) and the oil temperature (compression unit outlet).
On ( ) Stop (O) Stopped under pressure (F2) Reset (F3) Scrolling (F4) A connector situated behind PCI07 can be used for compressor remote control (option). • • • • •
2) Data The PCI07 display and the Leds provide: display of the operating status of the compressor at a • given instant, display of maintenance messages (alarms, defects, etc.) • display of compressor control parameters. •
3) Regulation The PCI07 executes compressor regulation. These functions include: control of no-load operation as soon as the pressure • measured by the pressure analog sensor reaches the regulation pressure control of load operation as soon as the pressure • measured by the analog pressure sensor reaches the minimum regulation pressure (regulation pressure – regulation deviation) • ordering of motor shutdown after the period of no-load operation inhibiting of motor restart if the pressure in the oil tank is • above 1.5 bars (RLR 75 at 220 or automatic restart option).
4) Control of condensate drain-off The frequency and the duration of drain solenoid valve opening can be programmed in order to adapt to the size of the machine and the volume of condensate to be evacuated.
5) Signalling Signallin g of maintenance operations As soon as a maintenance operation is required, either because the machine has reached a number of hours requiring work, or because a sensor has detected that a threshold has been reached, a yellow light flashes and a message indicating the operation to be executed is displayed. The machine does not stop.
4) Battery replacement replacement
6) Management Management of operating operating defects
The battery is used to keep date and time when the power supply is off. Its working life depends upon the length of time the machine is off. We recommend replacing the battery every 4 years. However, should the date and time disappear, change the battery as follows (no other parameter is lost): Turn the power off • Open the flap at the rear of the PCI07 • Replace the old battery with a new one ref. CR2032 • • Close the flap Reset the date and time •
As soon as a fault signal appears, the PCI07 stops the compressor, signals the fault through the red light of the reset key and displays a message allowing the cause of the incident to be quickly located. The 8 last faults occurring on the compressor are kept in the memory and can be displayed by a technician holding the electronic key (See 2.3).
1.2 - Functions
7) Programming Programming compressor startup startup and stopping After programming the timers, the real-time clock on the PCI07 allows automatic starting and stopping of the compressor. The clock which operates when the compressor is deenergized is supplied by a lithium battery with 8 years' service
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
1.3 - PCI front panel (Fig.1) 1) LED indicators
Reset key (F3)
Power supply indicator
Color: yellow Symbol: R
Color: green Symbol: lightning
This indicator remains on as long as the machine is energized.
Alarm indicator indicator Color: yellow Symbol: spanner
This indicator flashes as soon as a maintenance operation is needed, either because the machine has reached a number of hours requiring servicing, or because a sensor has detected a threshold. A message indicating the operation to be executed is displayed.
Under-pressure shutdown indicator (F2)
Pressing on the reset key: trips a lamp test and condensate drainage, in the presence of an alarm or a defect, displays the message for maintenance when the compressor is stopped, • when the machine is stopped, in defect or alarm mode, enables the defect or the alarm message to be cancelled after maintenance. If several defects or alarms are activated at the same time, it will be necessary to press on the reset key the same number of times necessary to eliminate them all, • enables the cancel of an under-pressure stop, • when the machine is stopped, enables the machine configuration information menu to be scrolled, • when the machine is operating, enables a return to the “onload” or “offload” display, • when in the programming or initialising menu, enables modification of settings. • •
Color: red
Machine start key
This indicator comes on as soon as the machine is stopped by the under-pressure stop key.
Color: green Symbol:
Fault indicator (F3)
Pressing on the key starts the machine.
Color: red
Machine stop key
This indicator comes on as soon as an operating fault is detected and has stopped the machine. A message indicates the nature of the fault.
Color: red Symbol: O
"On" indicator Color: green Symbol:
This indicator comes on as soon as a machine start has been requested. It goes out when a machine stop is requested through the machine stop key or when a fault trips machine stopping. During the compressor stop time-delay, the LED "on" indicator flashes.
2) Keys
Pressing on the O key: • stops the machine. Since the machine only stops after 30 seconds no-load operation minimum, stopping can be time lagged. During the period of time-lagged stopping of the compressor, this can be restarted by pressing on the key. • when the machine is stopped, enables the display of pressure, temperature and compressor status.
Data scroll key (F4) Color: yellow Symbol: • •
Under-pressure shutdown key (F2) Color: red Symbol: oil tank which empties
Pressing the "under-pressure shutdown" key: when the machine is operating, enables the machine to be stopped while maintaining the air pressure in the internal machine circuit during 2 or 3 minutes in order to: - drain the oil more easily, - carry out a check on the leaktightness of circuits under pressure, • when in the programming or initializing menu, enables validation of selected settings. •
briefly pressing this key allows successive displays of machine status data. pressing on the key for more than 3 seconds generates an input on the programming menu.
3) Display The 2-line, 16 character back-lit liquid crystal display panel can be used to display status, alarm, fault messages together with operating parameters (pressure, temperature, etc.). On energizing the compressor, an initialising message gives the version of the software displayed (e.g.: EPROM P01PCI21). After initialising, the display of the data and the time is used to detect an eventual disturbance in the memory.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
1.4 - PCI rear panel (Fig.2) 1) Description of inputs/outputs inputs/outputs
•
8-pole withdrawable connector for the option or the connection of the electronic key (X6).
•
10-pole withdrawable connector for the 5 control outputs (dry contacts) (X2): Controlled load: 250V, 6A nominal – Cos ϕ=1
5 connectors on the rear of the PCI can be used to connect the inputs/outputs and the PCI power supply. •
7-pole withdrawable connector for the 6 on/off i nputs (X3):
11.
Common
12.
KM2
Common from all on/off sensors.
1 and 2. KM3 Delta contactor
Star contactor
13.
Controls the delta contactor. 3 and 4. KM2
Controls the star phase on main motor startup. PSH1
Star contactor
High pressure switch
14.
Controls the star contactor. 5 and 6. KM1
Provides high pressure protection. DPSH1
Line contactor
Clogging
15.
Control of the line contactor. 7 and 8. SOV2
Detected by deoiler filter head losses. F1/Q1/F11
Regulation solenoid valve
Internal combustion engine, dryer or fan fault
16.
Controls the regulation vacuuming valve. 9 and 10. SOV1
Engine protection systems, main, dryer or fan. FS1 Water circulation
17.
solenoid
and
the
Dryer or condensate bleed solenoid valve.
Indicates the presence of water in cooling circuit. PSL1
Dryer operation or bleed control.
Pressure above 1.5 bar
Low pressure protection (restart). • •
5-pole withdrawable connector for 2 analog inputs (X5):
•
3-pole withdrawable connector to supply 12Vac (X4) (18, 19 and PE). Required power: 6VA / 12Vac
20 and 21. TS Temperature probe
Analog sensor for measuring the temperature at element output. 22 to 24. PT Pressure sensor
Analog sensor for measuring the pressure at the machine output (user).
In addition to these 5 connectors, a double Faston lug on rear plate of the PCI allows connection of the PE conductor and cable screening. Push button F1 in the middle of the rear panel of the PCI allows access to the initializing menu.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Fig.1 : Front panel of the PCI07
Fig.2 : Rear panel of the PCI07
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
1.5 - Definitions •
•
•
•
Alarm An alarm informs the user that a maintenance operation is necessary either because the machine has reached a certain number of hours' operation, or because a sensor has detected a threshold. An alarm does not lead to compressor shutdown. It is indicated visually by the yellow alarm indicator light LED flashing and by a message informing the operator of the nature of the alarm or the operation to be executed.
•
Remote control
•
Remote control option
•
Serial port option
•
Automatic restart restart
Fault A fault leads to compressor shutdown and is linked to a machine malfunction. It is signalled by the red LED associated with the F3 reset key and by a message informing the operator of the nature of the defect (e.g.: overpressure, temperature fault, etc.).
Analog sensor
An analog sensor is a sensor which has a continuous measuring range. The PCI07 manages two analogue inputs: one for the pressure sensor (0 to 17 bar), and one for the oil temperature probe (-20 to +151°C).
Timer A timer is used to program automatic startup and shutdown of the compressor. Starting and stopping can be programmed for one day of the week, work days (Monday to Friday), week-end or every day of the week. 8 timers can be programmed. Examples: •
•
Timer 1 active for Monday, Start timer 1 = 8 a.m. and stop timer 1 = 4 p.m. the compressor will operate on Mondays from 8 a.m. until 4 p.m.. Timer 5 active for Thursday, Start timer 1 = 6.30 a.m. and stop timer 1 = 8.15 p.m. the compressor will operate on Thursdays Thursdays from 6.30 a.m. until 8.15 8.15 p.m..
When a compressor is pending restart by a timer, the message « WARNING AUTO RESTART BY TIMER » moves through the display. If the compressor is pending restart by a timer, the compressor can be forced to start manually by dual pressing on the start key ( I ). This forced operation will not alter the timer settings. Examples :
In the examples above, if the key is double pressed before Monday 8.00 a.m. or Thursday 6.30 a.m., the compressor will start and stop automatically on Monday at 4 p. m. or on Thursday at 8.15 p.m..
•
Regulation pressure / differential pressure
•
Possibility of starting and stopping the compressor remotely. In all cases, local mode shutdown has priority. If the compressor is stopped remotely, it will be possible to restart it remotely and the ‘stopping’ message will be displayed. If the compressor has been stopped locally, its remote restart will be impossible. The remote start/stop mode has priority over timer operation: - When a compressor i s stopped remotely, the « WARNING: REMOTE RESTART » message moves through the display. - If a compressor is started remotely when outside the operating times programmed on the active timers, the « WARNING AUTO RESTART BY TIMER » message moves through the display.
This option allows the compressor to be started or stopped remotely and a general fault reported (light, siren, etc.). - Operation as main compressor and back-up for 2 compressors (serial cable). - To control and display display the status of a remote compressor (serial interface).
Using an interface, this option allows alternating operation of 2 compressors or all the operating parameters from the compressor to be displayed on the PC.
This option enables automatic restart of the compressor after a power outage.
Max. number of starts authorized per hour This function is for defining the minimum operating time of the motor between its last startup and automatic shutdown as a result of prolonged no-load operation. If, on a prolonged no-load operation, the motor no-load operating time is exceeded, compressor shutdown will only be authorized if the number of maximum restarts per hour is complied with. Example: -
-
The maximum number of restarts authorized per hour is set at 3, the motor operating time is 10 minutes.
In these conditions, the motor must be capable of operating for 20 minutes minimum before its shutdown is
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Chapter 2 - Menus 2.1 - Initialisation menu
For selecting the display language, maintenance maintenance cycles, startups, condensate drain and real-time clock. Menu access condition: Access to menu: Exit the menu: Modify selection: Validate selection:
machine shutdown press on F1 (PCI rear panel) press on F1 (PCI rear panel) press on F3 press on F2
LANGUAGE FRANÇAIS ENGLISH ESPANOL ITALIANO DEUTSCH PORTUGUESA NEDERLANDS
Language
AIR FILTER OIL FILTER SEPARATOR
Maintenance cycles
OIL CHANGE BEARINGS OFFLOAD MINIMUM TIME UNIT NUMBER CONDENSATE DRAIN FREQ. CONDENSATE DRAIN DURATION MOTOR STARTUPS STAR TIME MOTOR STARTUPS No/HOUR
Startups and drains
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
2.2 - Programming menu
For setting the regulation and the timers Menu access condition: Menu access: Exit the menu: Modify the selection: Validate the selection:
machine stopped press on F4 for more than 3 seconds press on F4 press on F3 press on F2
REGULATION PRESSURE DIFFERENTIAL PRESSURE INTERNAL REGULATION EXTERNAL REGULATION
Régulation
STAND-BY PRESSURE DIFFERENTIAL STAND-BY OPERATION WITH TIMERS WITHOUT TIMER TIMER 1 ACTIF ON TIMER 1 OFF TIMER 1 ON TIME HOUR TIMER 1 ON TIME MINUTES TIMER 1 OFF TIME HOUR TIMER 1 OFF TIME MINUTES
Timers
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
2.3 - Machine status information menu For displaying hours' operation, maintenance cycles, date and hour
Menu access condition: Access to the menu: Scrolling: Exit the menu:
compressor stopped, load or no-load configuration press on F4 press on F4 press on F3 (compressor operating) or key O (compressor stopped)
TOTAL HOURS ONLOAD HOURS
Hours operation
LOAD RATIO AIR FILTER OIL FILTER SEPARATOR
Maintenance
OIL CHANGE BEARINGS Tuesday 01/01/98 12 : 00
Date and time
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
2.5 - Machine configuration information menu
For displaying the startup mode, the pressure and temperature protection limits and the option.
Condition of access to menu: Access to menu: Scrolling: Exit the menu:
machine stopped press once on F3 press on F3 press once on the O key
MANUAL AUTOMATIC RESTART AIR WATER COOLING
Machine configuration
MAXIMUM PRESSURE TEMPERATURE MAX TEMPERATURE MIN OPTION SERIAL PORT OFF SERIAL PORT ON SERIAL INTERFACE SERIAL CABLE
P and T protections
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Chapter 3 - Description of messages 3.1 - Setting of machine operating parameters ** LANGUAGE selection ** (Initializing menu)
LANGUAGE
Select the language for displaying the information on the PCI (Eight language options).
** Setting the MAINTENANCE CYCLES ** (Initializing menu)
AIR FILTER OIL FILTER SEPARATOR
Input the air filter life (hours).
OIL CHANGE
Input the oil life (hours).
BEARINGS
Input the service life of the main motor bearings (hours). 100 to 9900h / 100h. --- : counter inhibited
Input the oil filter life (hours). Input the separator filter life (hours).
** Setting STARTUP and DRAIN ** (Initializing menu)
OFFLOAD MINIMUM TIME UNIT NUMBER CONDENSATE DRAIN FREQ. CONDENSATE DRAIN
Input the compressor no-load operating time before motor stops (minutes). Input the machine number. Input the frequency of condensate drain valve opening (minutes). Input condensate drain valve opening time (seconds).
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
** Setting the REGULATION pressure ** (Programming menu)
REGULATION PRESSURE DIFFERENTIAL PRESSURE STAND-BY PRESSURE DIFFERENTIAL STAND-BY
Input the regulation pressure leading to c ompressor no-load operation (bars). Input the deviation between the regulation pressure and the pressurizing pressure corresponding to the no-load operation range (bars). OPTION
When two compressors are operating alternately, inputting the regulation pressure leads to no-load operation of the back-up compressor (bars). OPTION
When two compressors are working alternately, input the deviation between the regulation pressure and the pressurizing pressure for the backup compressor corresponding to the no-load operation range (bars).
** Setting the REGULATION mode ** (Programming menu)
INTERNAL REGULATION EXTERNAL REGULATION
OPTION
Operation with a serial interface. The regulation instructions set on PCI07 and the the analog pressure sensor are used for load and no-load operation of the compressor. Regulation is dependent on on the internal compressor settings. OPTION
Operation with a serial interface. The load and no-load start orders are external external to the compressor (load/no-load start inputs from the serial interface). The compressor internal pressure sensors remain active for the protection functions.
** Selection and setting of TIMERS ** (Programming menu)
OPERATION WITH TIMERS OPERATION WITHOUT TIMERS TIMER X
Compressor operation through timers (8 timers can be programmed to stop and start the machine automatically). Compressor operation without timers.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
3.2 - Compressor data ** RESTART and COOLING modes ** (Machine configuration menu)
MANUAL RESTART AUTOMATIC RESTART AIR COOLING WATER COOLING DRAIN DURING STOP
Manual restart of the compressor after a current outage lasting more than 250 ms. OPTION Automatic restart of the compressor after a current outage. outage. Air-cooled compressor. Water-cooled compressor. NO: condensate drainage operations operations only carried out during compressor load operation (default) (default) YES: condensate drainage operations carried out out whatever the compressor operating configuration (load operation, no-load operation, energized, etc.)
** PRESSURE AND TEMPERATURE PROTECTIONS ** (Machine configuration menu)
MAXIMUM PRESSURE
Maximum value authorized for regulation pressure setting (bar) = maximum service pressure protection).
TEMPERATURE MAX
Maximum compressor operating temperature (C°) leading to compressor fault trip (temperature protection).
TEMPERATURE MIN
Minimum compressor operating temperature (°C) It is impossible to stop the compressor below the minimum operating temperature (temperature protection). --- : the low temperature safety mechanism is inhibited.
** OPTION **
(Machine configuration menu)
SERIAL CONNECTION OPTION OFF
No option has been selected. The compressor operates in self-contained mode and makes adjustments based on its own settings and sensors. sensors. Default adjustment.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
** DRYER ** (machine configuration menu)
DRYER ON
Actives the On/Off control of the dryer via the digital output output SOV1.
(initialization menu)
Timeout for compressor startup after the dryer: The cooling dryer temperature drops before the compressor starts. This timeout is also taken into account for the remote On/Off control. The timeout is not taken into account with automatic restart.
DRYER DURATION
** STATUS / PRESSURE ** 00.0 BAR
000 °C
POWER ON ONLOAD OFFLOAD
DUTY ONLOAD DUTY OFFLOAD ST-BY ONLOAD ST-BY OFFLOAD
Displays the use pressure measured at the machine output (bars) and the temperature at the discharge of the compressor part (C°). The compressor is energized and stopped. The compressor is operating at full load or at part load. The pressure measured by the analog sensor at the machine output is less than the regulation pressure. The compressor operates at nil flow and with the oil tank empty. The pressure measured by the analog sensor at the use is within the regulation deviation. No-load operation start: • The use pressure (analog pressure sensor) reaches the regulation pressure. End of no-load operation: • The compressor output pressure falls and reaches the pressurizing restart pressure (regulation pressure – regulation deviation). The offload operation time exceeds the offload minimum time and the compressor stops (if allowed by the maximum number of starts per hour data). In the event of alternating operation of 2 machines (optional), message displayed on the compressor used as main compressor when this operates at full load or part load. In the event of alternating operation of 2 machines (optional), message displayed on the compressor used as the main one when this operates at nil flow and with the oil tank empty. In the event of alternating operation of 2 machines (optional), message displayed on the regulating compressor as the backup when operating at full load or part load. In the event of alternating operation of 2 machines (optional), message displayed on the regulating compressor as backup when operating at nil flow and with empty oil tank. Flashing display during compressor time-lagged stop.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
** TEMPERATURE PROTECTION TEST ** (From programming menu)
TEMPERATURE SYSTEM TEST SENSOR OK
Test of the temperature protection trip has been selected. The maximum temperature setting is lowered to 60 °C. The compressor is on operating standby ready to begin the test. The temperature protection trip test has been executed and the compressor fault has been activated. The test is valid. Reset by pressing on the reset key F3. The maximum temperature setting is brought to its initial value for normal operation.
** OTHER information ** STAR STARTING
Displayed during all the motor start star phase (based on the star duration setting).
DELTA TRANSITION
Displayed while the microprocessor checks that transfer to delta mode has indeed been executed (around 3 seconds). At the end of the passage onto delta, the compressor transfers to load and condensate drainage takes place.
PRESSURE ABOVE 1.5 BAR
OPTION for belt drive compressor The compressor is on restart standby. The pressure in the tank is greater than 1.5b. Restart as soon as the pressure in the tank falls below 1.5 bar.
STOP UNDER PRESSURE, DOT NOT RESTART
The compressor has been stopped using the under pressure stop key F2. Restart is only possible after resetting (key F3) and for a pressure in the tank less than 1.5 b (OPTION for belt drive compressor).
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
3.4 - Maintenance CHANGE AIR FILTER CHANGE AIR/OIL SEPARATOR CHANGE OIL CHANGE OIL FILTER MOTOR BEARINGS LUBRICATION
1st display of the message when the remaining air filter life is 5 hours. 2nd display of the message when the air filter life counter has reached 0. After changing the filter and resetting the life counter, cancellation cancellation after pressing on reset key F3. 2 case: • displayed after deoiler clogging detected by differential pressure gauge. 1st display of the message when the separator filter life is 5 hours. 2nd display of the message when the separator filter life counter has reached 0. After changing the filter and resetting the life counter, cancellation cancellation after pressing on reset key F3. 1st display of message when the remaining oil life is 5 hours. 2nd display of the message when the oil life counter reaches 0. After drainage and resetting the life counter, counter, cancellation after pressing on reset key F3. 1st display of message when the remaining oil filter life is 5 hours. 2nd display of the message when the oil filter life counter reaches 0. After changing the filter and resetting the life counter, cancellation cancellation after pressing on reset key F3. 1st display of the message 5 hours before main motor bearing lubrication. 2nd display of the message when the bearing lubrication counter has reached 0. After bearing lubrication and reinitializing the counter, cancellation after pressing on the reset button F3.
3.5 - Faults SHORT CIRCUIT IN TEMPERATURE
Compressor stopped. Possible causes:
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
HIGH PRESSURE FAULT
HIGH TEMPERATURE FAULT
WATER FLOW FAULT
The HP is tripped after detecting overpressure in tank or the analog pressure sensor at the machine output has reached the safe HP level (max. pressure+1bar) . Compressor stops. Possible cause: intake chamber valve does not close • Analog pressure sensor fault • Restart possible if pressure falls below HP trip value after resetting by pressing on reset key F3. The analog temperature probe measures a temperature at the element outlet which is above the compressor maximum operating temperature (temperature protection). The compressor is stopped. Possible causes: low oil • ambient temperature too high • • obstruction of cooling air passage through oil radiators clogging of oil/water exchanger • obstructed oil circuit • stopped fan • defective temperature probe • Restart possible if the temperature has fallen below the maximum safe temperature and after resetting by pressing on reset key F3. This fault is detected when the compressor is onload or offload (water cooling). The fault is displayed after a 6 second confirmation time laps. The compressor stops. Possible causes: general inlet closed • solenoid valve has not opened • clogging of exchangers •
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Chapter 4 - Options The 8-pole connector situated behind the PCI07 is used to connect up the 2 following options: - Serial cable - Serial connection interface In order to connect one of the options, PCI07 has to be set to 'SERIAL CONNECTION OPTION ON' (machine configuration menu).
Alternancy: The operation described previously is reversed every 24 hours or every week based on the selected operating mode. During a permutation, compressor A is regulated according to the main set point and compressor B according to the backup set point. On the next permutation, compressor A regulates according to the backup set point and compressor B according to the main set point.
Timer management:
This option can be used to operate 2 compressors alternately after connecting their PCI07 using the connection cable.
Each compressor operates through its own timers. As soon as one compressor is outside its programmed operating times, the « CAUTION: AUTOMATIC RESTART BY TIMER » message is displayed. The second compressor then operates independently and based on its own settings and its own sensor. The « MAIN » and « BACKUP » display disappears. When both compressors are in their programmed operating times, the main/backup mode is automatically reactivated.
Configuration of the PCI07:
Protection management
To allow alternating operation of 2 compressors, configure the PCI07 of both compressors using the explanatory notice ref. 62 139 391 11.
On a malfunction of one of the two compressors or shutdown under pressure, this transfers to autonomous operation and each one regulates according to its own measured pressure and its own regulation set point. Thus, if a fault appears on one set or if it is stopped by a user, the other set is not blocked and transfers onto autonomous operation.
4.1 - Serial cable Alternating operation of 2 compressors (Kit ref.: 62 590 810 00, cable ref.. 62 363 691 00)
Cabling:
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Inputs / outputs:
(See diagram ref. 62 139 444 00)
Inputs: • input 1: remote start / stop This input controls starting and stopping of the compressor. • input 2: load / no-load operation This input can be used to force load or no-load operation of the compressor. The input is activated if the external regulation mode is selected in the programming menu. Outputs: • output 1: unused • output 2: compressor internal regulation status Pressure switch type output reflecting the compressor theoretical operating mode (load or no load) relative to the regulation instructions set on PCI07. Active output when operating with load. • output 3: local / remote regulation This output reflects the regulation m ode configured on PCI07 (internal or external regulation). With internal regulation, the compressor uses its own settings and internal pressure sensor to regulate operation. In external regulation, input 2 is used for the load or no-load start order. Active output in external regulation. • output 4: load operation Active output when the compressor motor is rotating • output 5: availability Active output when the compressor is ready to operate (no fault, machine energized and start pressed)
Chapter 5 - Temperature protection test The temperature protection trip of a compressor can be tested. This test has to be carried out once every year in order to check that this protection operates properly.
Test procedure: • •
•
Set the compressor to shut down, and energize. When the temperature measured by the analog sensor exceeds 60 °C, place the cursor in the programming menu (press on key F4 longer than 3 seconds). In the programming menu, press on keys Ο and | simultaneously. The « TEMPERATURE SYSTEM TEST » message comes on.
When the « TEMPERATURE SYSTEM TEST » message is displayed, the compressor is ready to carry out a temperature protection trip test. For this test, the maximum operating temperature setting is less than 60 °C in order to cause tripping of a protection in the normal conditions of operation. • •
Set the compressor to On by pressing on key |. Wait for the temperature protection to trip. Check that this trip takes place at 60 °C.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Chapter 6 - Factory settings Data Data
Messa Message ge examp example le
Unit Unit
Possib Possible le choice choicess
Language selection
English
/
Air filter service life Oil filter service life
Air filter Oil filter
h h
Français English Espanol Italiano Deutsch Nederlands Portuguesa Svenska 500 to 9500 500 to 9500
Separator service life
Separator
h
500 to 9500
Factor Factoryy settin setting g
English
2000 2000 2000 – 3000, 15 - 40
4000 h
40 to 220 6000 h
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Chapter 7 - Alphabetic - Alphabetic list of messages
LISTE OF MESSAGES
TYPE OF MESSAGE
*** A *** Air cooling Air filter Automatic restart restart
info setting/info info/option
*** C *** Change air filter
maintenance
PAGE 10,13 7,9,11,14 10,13 16
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
LISTE OF MESSAGES
TYPE OF MESSAGE
*** O *** Offload Offload minimum time Oil change Oil filter Onload Onload hours Operation without timer Operation with timers
info setting setting/info setting/info info info setting setting
*** P ***
PAGE 14 7,11 7,9,11,14 7,9,11,14 14 9,14 8,12 8,12
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
LISTE OF MESSAGES *** W *** Warning : auto restart Warning auto restart by timer Warning, high temperature Warning : remote restart Water cooling Water flow fault
TYPE OF MESSAGE
PAGE
info info alarm info info fault
15 6,15,18 15 6,15 10,13 17
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
NOTA _____________________ ________________________________ ______________________ ______________________ ______________________ ______________________ ______________________ _______________________ _______________________ ______________________ ________________________ ________________________ _____________ __ _____________________ ________________________________ ______________________ ______________________ ______________________ ______________________ ______________________ _______________________ _______________________ ______________________ ________________________ ________________________ _____________ __ _____________________ ________________________________ ______________________ ______________________ ______________________ ______________________ ______________________ _______________________ _______________________ ______________________ ________________________ ________________________ _____________ __ _____________________ ________________________________ ______________________ ______________________ ______________________ ______________________ ______________________ _______________________ _______________________ ______________________ ________________________ ________________________ _____________ __ _____________________ ________________________________ ______________________ ______________________ ______________________ ______________________ ______________________ _______________________ _______________________ ______________________ ________________________ ________________________ _____________ __ _____________________ ________________________________ ______________________ ______________________ ______________________ ______________________ ______________________ _______________________ _______________________ ______________________ ________________________ ________________________ _____________ __ _____________________ ________________________________ ______________________ ______________________ ______________________ ______________________ ______________________ _______________________ _______________________ ______________________ ________________________ ________________________ _____________ __ _____________________ ________________________________ ______________________ ______________________ ______________________ ______________________ ______________________ _______________________ _______________________ ______________________ ________________________ ________________________ _____________ __
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
NOTA
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Titles you can't find anywhere else
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.