TLID1007C
Operateaforklift
Armstrong’sDriverEducation
LearnerGuide
TLID1007C Operate a forklift
Page 2
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Contents What this Learner’s Guide is about........ about ................ ................. ................. ............... ....... 2 Planning Planning your learning learning ................ ........................ ................. ................. ................ ................ .......... .. 3 How you will be assessed assessed........ ................. ................. ................ ................ ................. ............. .... 6 Section 1.......................... 1... ....................... ...................... ..................... ....................... . 8 Before Before you drive the forklift ................ ........................ ................. ................. ................ ........... ... 8 Section 2......................... 2... ...................... ...................... ...................... ...................... 16 Types Types of forklifts forklifts and attachments attachments ................ ........................ ................. ............... ...... 16 Section 3............................. 3...... ....................... ...................... ..................... ................... 52 Forklift Forklift safety safety ................ ......................... ................. ................ ................ ................. ................. .............. ...... 52 Section 4............................ 4...... ...................... ...................... ...................... ................... 66 Driving Driving the forklift forklift ................ ......................... ................. ................ ................ ................. ................ ....... 66 Additional resources....................... resources ....................... ..................... ...................... ..... 94 Feedback Feedback on activities activities ................. ......................... ................ ................. ................. ................ ................ .......... .. 96
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 3 ADELG1011
TLID1007C Operate a forklift
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 1 ADELG1011
TLID1007C Operate a forklift
What this Learner’s Guide is about ThisLearner’sGuideisabouttheskillsandknowledgerequiredto operateaforklift,includingcheckingforkliftcondition,drivingthe forklifttofulfiloperationalrequirements,monitoringsiteconditions andmonitoringandmaintainingforkliftperformance.Assessmentof thisunitwillusuallybeundertakenwithinalicensingexamination conductedby,orundertheauthorityof,therelevantstate/territory OHSAuthority. Personsachievingcompetenceinthisunitwillneedtofulfilallofthe relevantstate/territoryOHSregulatoryrequirementsconcerningthe safeoperationofforklifts. TheElementsofCompetencyfromtheunitTLID1007COperatea forkliftcoveredinthisLearner’sGuidearelistedbelow. Checkforkliftcondition Drivetheforklift Operateaforklifttohandleloads Monitorsiteconditions Monitorandmaintainforkliftperformance ThisunitofcompetencyisfromtheTransportandLogisticsTraining Package(TLI07).
Page 2
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Planning your learning Itisimportanttoplanyourlearningbeforeyoustartbecauseyoumay alreadyhavesomeoftheknowledgeandskillsthatarecoveredinthis Learner’sGuide.Thismightbebecause: •
•
youhavebeenworkingintheindustryforsometime, and/or youhavealreadycompletedtraininginthisarea.
Togetherwithyoursupervisorortrainerusethechecklistsonthe followingpagestohelpyouplanyourstudyprogram.Youranswersto thequestionsinthechecklistwillhelpyouworkoutwhichsectionsof thisLearner’sGuideyouneedtocomplete. ThisLearner’sGuideiswrittenwiththeideathatlearningismademore relevantwhenyou,thelearner,areactuallyworkingintheindustry. Thismeansthatyouwillhavepeoplewithintheenterprisewhocan showyouthings,discusshowthingsaredoneandanswerany questionsyouhave.Alsoyoucanpractisewhatyoulearnandseehow whatyoulearnisappliedintheenterprise. IfyouareworkingthroughthisLearner’sGuideandhavenotyetfound ajobintheindustry,youwillneedtotalktoyourtraineraboutdoing workexperienceorworkingandlearninginsomesortofsimulated workplace.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 3 ADELG1011
TLID1007C Operate a forklift
Section 1: Before you drive the forklift Areyouableto:
Yes
No
1. explainthecurrentlegalrequirementsfor youtobeabletodriveaforkliftinyour workplace? 2. listyourresponsibilitiesand‘dutyofcare’ as a forklift driver? 3. listyouremployer’sresponsibilities concerning forklift operations?
Section 2: Types of forklifts and attachments Areyouableto:
Yes
No
1. explainthedifferencebetweenthe counterbalance,straddle,orderpicker and side-loading forklifts? 2. listtheadvantagesanddisadvantagesof internal combustion and electric forklifts? 3. identify the major forklift components? 4. interprettheforkliftmanufacturer’sdata plate? 5. defineloadcenterdistanceandexplain how it affects forklift stability? 6. identify forklift attachments and their uses? 7. demonstratesafeuseofattachments including jibs and associated equipment?
Page 4
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Section 3: forklift safety Areyouableto:
Yes
No
Yes
No
1. identifypersonalsafetyequipmentused while inspecting and operating a forklift? 2. explainthesafetystepsthataforklift driverneedstocompletebeforetheydrive the forklift? 3. stateforkliftsafetyrequirementswith regardstodrivingtheforklift,forkliftand forkliftequipment,loads,workplace environment,personalandworkplace safety?
Section 4: Driving the forklift Areyouableto: 1. conductapre-operationalforkliftsafety check? 2. conductapre-operationalworkareasafety check? 3. report the results of safety checks? 4. drive a loaded and an unloaded forklift? 5. stack and de-stack a load? 6. load and unload a truck? 7. refuel or recharge a forklift?
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 5 ADELG1011
TLID1007C Operate a forklift
How you will be assessed AssessmentofthisUnitofCompetencywillincludeobservationofreal orsimulatedworkprocessesusingworkplaceproceduresand questioningonunderpinningknowledgeandskills.Itmustbe demonstratedinanactualorsimulatedworksituationunder supervision. Youwillberequiredto: •
Page 6
completeanoralorwrittentheoryassessmentofforklift operation
•
driveaforkliftsafelyandcompetently
•
maintainalogbookofpracticeundertakenonaforklift
© Australian National Training Authority 2003
TLID1007C Operate a forklift
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 7 ADELG1011
TLID1007C Operate a forklift
Section 1 Before you drive the forklift
Page 8
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Section outline Areascoveredinthissection
Legalrequirements Yourresponsibilities Youremployer’sresponsibilities
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 9 ADELG1011
TLID1007C Operate a forklift
What do you need to know about forklift legislation? Legislation refers to certain rules and conditions that you need to follow.
Thismaybe: •
beforeyouarelegallyqualifiedtodriveaforklift
•
whileyouaredrivingaforklift.
Althoughitisnotquitethesame,thinkofitassimilartothedriver’s licencesystem.Beforeyoucanlegallydriveacarontheroadyouhave tolearnwhattodoandthenbeexaminedondrivingthecar.Youneed tocompleteatheorytestandthenbeassessedonyourdrivingskills. Forkliftlegislationrequiresyoutodothesame. EachState/Territorymayhaveslightlydifferentlegislation.Insome States/Territoriesparticulartrainingneedstobeundertakenandin otherStates/Territoriesyouwillneedtoobtaina‘Certificateof Competency’beforeyoucandrivetheforklift.Howeveralltraining andlicenceswillreflecttheNationalGuidelinesforOccupationalHealth andlicenceswillreflectthe NationalGuidelinesforOccupationalHealth andSafetyCompetencyStandardsfortheOperationofLoadshifting EquipmentandOtherTypesofSpecifiedEquipment[NOHSC:7019 (1992)]. (1992)]. Therefore,itisessentialtoknowexactlywhatyourrequirementsare.
Page 10
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 1: What is the forklift legislation in my state/territory? As the forklift legislation differs in each state/territory, you need to find out what you need to do before you can drive a forklift in your workplace. Research into what the legislation requires you to do before you can drive a forklift in your your State/Territory. Find out what what regulations cover the use of a forklift in your State/Territory and then what requirements you need to do or fulfil before you can operate the forklift in the workplace. You can do this by obtaining information information from the following resources: •
Department for Industrial Affairs
•
Worksafe or Workcover Authority
•
Occupational Health & Safety Authority
•
the people you work with who operate that machinery
•
your workplace supervisor or trainer.
When you have completed this task take your answers to your trainer for checking. Forklift legislation In your own words, write down what you need to do before you can drive a forklift in your workplace. ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 11 ADELG1011
TLID1007C Operate a forklift
What is ‘Duty of Care’? TheOccupationalHealth,SafetyandWelfareActapplicableinyour State/Territorynotonlyrequiresyoutofulfilcertainobligationsbefore youdriveaforklift,butalsowhileyouaredrivingaforklift. Theseobligationsarelegalobligationsandyouarerequiredtocomply withthembylaw.Failuretodosowoulddeemyouresponsibleand liableintheeventofanaccident. Workersarerequiredtoshowadutyofcareatalltimes.
Page 12
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 2: Define ‘Duty of Care’ Discuss the legal requirements and your Occupational Health, Safety and Welfare requirements with: •
your supervisor and trainer
•
your OHS committee
•
your workmates
•
Workcover Authority.
Then determine what the term ‘Duty of Care’ means to you, as a forklift driver. Think of it in terms of the following: Personal safety ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ Safety of workmates ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ Safe work practices ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 13 ADELG1011
TLID1007C Operate a forklift
What are my employer’s responsibilities? Youremployeralsohaslegalresponsibilitiestocomplywith.Asthese responsibilitiesdirectlyaffectyou,itwillbehelpfulifyouareawareof theseresponsibilities.
Page 14
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 3: Employer responsibilities Think about the type of responsibilities your employer may have towards you, the forklift driver. Write these responsibilities responsibilities in the spaces provided below. Facilities ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ Equipment ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ Information ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ Systems of work ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ ____________________________ __________________________________________ ________________________ __________ Refer to your OHSW Act to check your answers then discuss with your trainer.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 15 ADELG1011
TLID1007C Operate a forklift
Section 2 Types of forklifts and attachments
Page 16
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Section outline Areascoveredinthissection
Typesofforklifts Powersourcesormodesofpropulsion Componentsoftheforklift Attachmentsthatcanbefittedtotheforklift
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 17 ADELG1011
TLID1007C Operate a forklift
What are the types of forklifts? Theforkliftisamaterialshandlingvehiclethatiswidelyusedinthe transportindustry.Itisinvaluableforitsabilitytomovealargeamount ofmaterialinaveryshorttimeusingaminimumoflabour. Therearefourmaintypesofforkliftthatyouarelikelytoseeinthe industry.Theyare: •
•
counterbalancedforklift straddleforkliftorreachtruck-alsoknownasnoncounterbalanced
•
orderpickers
•
sideloadingforklift.
Eachoftheseforkliftsareusedfordifferentpurposesinthe workplace.Theycanhoweverbeusedforavarietyoftasks.
Page 18
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 4: Identification of the types of forklifts Investigate the difference between the four main types of forklifts. You can gain this information from a variety of sources such as: •
sales brochures from retail outlets
•
materials handling magazines
•
transport and warehouse magazines
•
the Internet
•
libraries
•
books
•
previous knowledge and experience.
A worksheet is provided for your use and is located on the following pages. Counterbalance forklift What does a counterbalanced forklift look like? (draw or find a picture and place in the space opposite)
Why is it called a ‘counter balanced’ forklift?
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 19 ADELG1011
TLID1007C Operate a forklift
Where is the balance point or fulcrum of a counterbalanced forklift found?
List the two main power source options that you could find on a counterbalanced forklift.
Straddle forklift or reach truck What does a straddle forklift look like? (draw or find a picture and place in the space opposite)
Page 20
© Australian National Training Authority 2003
TLID1007C Operate a forklift
How is the weight of the load distributed on a straddle forklift?
What is a straddle forklift primarily designed for?
What is the primary power source for straddle forklifts?
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 21 ADELG1011
TLID1007C Operate a forklift
Order pickers What does an order picking forklift look like? (draw or find a picture and place in the space opposite)
Why is it called an ‘order picker’?
What is the difference between an order picker and a straddle forklift?
Page 22
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Side loading forklift What does a side loading forklift look like? (draw or find a picture and place in the space opposite)
Why is it called a ‘side loading’ forklift?
What types of loads are handled by the side loading forklift?
Give two examples of workplaces that might use the side loading forklift.
There is feedback on this activity at the back of this Learner’s Guide.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 23 ADELG1011
TLID1007C Operate a forklift
What are the power sources for forklifts? Powersourcesormodesofpropulsionforforkliftscanbedividedinto twomaintypes.Theyare: •
internalcombustion(fuels)
•
electric(battery).
Theinternalcombustionmotorinforkliftsissimilartothatusedin motorvehiclesandisdesignedtooperateonavarietyoffuelssuchas: •
petrol
•
diesel
•
LPG(LiquidPetroleumGas)
•
naturalgas.
Electricforkliftsarebatterypoweredforklifts.Abankofbatteriesor oneverylargebatteryisusedtopowertheforkliftinsteadoffuel substances.Electricpoweredforkliftsarebecomingmoreandmore popularwithinindustrybutelectricpoweredforkliftsalsohavesome disadvantages.
Page 24
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 5: Advantages and disadvantages of electric powered forklifts Discuss the advantages and disadvantages of electric forklift with one or more of the following: •
your trainer
•
your workmates
•
someone who drives an electric powered forklift
•
forklift distributors.
Then complete the worksheet on the next page.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 25 ADELG1011
TLID1007C Operate a forklift
Advantages of electric powered forklifts
Disadvantages of electric powered forklifts
There is feedback on this activity at the back of this Learner’s Guide.
Page 26
© Australian National Training Authority 2003
TLID1007C Operate a forklift
What are the major components of a forklift? Just as a car has many features and components that you need to know before you drive it, so does a forklift. As you know, different cars have different features with components being in different places. places. For example, the handbrake in a Holden may be in a different place to the handbrake in a Ford. Forklifts are exactly the same, forklifts forklift s will have similar components but they may be located in different places.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 27 ADELG1011
TLID1007C Operate a forklift
Activity 6: forklift components Match the components listed on the right-hand side of the page to the number shown on the forklift diagram.
Component
Number
Overhead guard Steering wheels Load Backrest Forks Mast Drive wheels Counterbalance Hoist chains Manufacturer’s data plate Parking brake
There is feedback on this activity at the back of this Learner’s Guide.
Page 28
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Itisimportanttounderstandhowsomeofthesecomponentscan effectthesafeoperationoftheforklift.Forthisreasonyouwillneed toknowabout: •
typesanduseofdifferenttyres
•
typesofforks(tines)available
•
mastandliftingmechanism
•
forkliftcontrols.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 29 ADELG1011
TLID1007C Operate a forklift
Activity 7: Components that can effect safe operations Research into the topics listed below: •
forklift tyres
•
forks
•
mast
•
forklift controls.
Research into the types available and their use in your industry. You can research into this by: •
discussing with your trainer
•
discussing with a forklift trainer
•
reading manuals and books.
A worksheet is provided to guide you in completing this activity.
Page 30
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Component
Types available
Uses and limitations
Tyres
(Example) Pneumatic tyres
Kind to floor surfaces, possibility of puncture, common on counterbalance forklifts
Forks
Masts
Forklift controls
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 31 ADELG1011
TLID1007C Operate a forklift
What information is included on the Manufacturer’s Data Plate? Bylaw,everyforkliftisrequiredtohaveamanufacturer’sdataplate. Thisdataplateshouldincludethefollowinginformation: •
maximumsafeworkingload
•
loadcentredistance
•
maximumliftheight
•
make,modelandserialnumber
•
masttilt(indegrees)
•
tyretypeandrecommendedpressure
•
grossvehicleweight
•
attachmentdetails(ifoneisfitted).
Itiscriticalthatyouknowtheinformationonthemanufacturer’sdata platesothattheforkliftisdrivenandusedwithinthesafeoperating capacity.
Page 32
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 8: Data plate information Using the activity work sheet, complete the definition and then select one of your workplace forklifts and give actual data plate readings.
Information
Definition
Load centre distance
(you can indicate with a drawing)
Data plate information
Maximum safe working load
Maximum lift height
Mast tilt degrees
There is feedback on this activity at the back of this Learner’s Guide.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 33 ADELG1011
TLID1007C Operate a forklift
What is load centre distance? Theloadcentredistanceisthemostimportantandmostdifficult concepttounderstandinforkliftdriving.Theloadcentredistance directlyaffectstheforklift’sstabilityandthereforeaffectssafetyas well. Tounderstandtheloadcentredistanceyouneedtoknowwhat ‘centreofgravity’isandhowtocalculatethecentreofgravityofan object. Yourtrainerwillhelpyouwiththisconcept,butingeneral,thecentre ofgravityofanobjectiswhereitwouldbalanceinalldirections(ifyou couldsuspendtheobjectfromthispoint).Forexample,fora basketballasitisperfectlysymmetrical,itwouldbeattheverycentre oftheball.Foraplate,itwouldbethecentreofitsbaseandhalfway throughthebase.Forabrick,itwouldbeatthepointwheretwo diagonallinesdrawnacrossthefaceofthebrickmeetandthenhalf waythroughthebrick.
Page 34
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 9: Centre of gravity Indicate where the centre of gravity is on the following shapes:
1200mm
2.2m 1800mm
1.8m
800mm diameter
1.5m
2.5m
There is feedback on this activity at the back of this Learner’s Guide.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 35 ADELG1011
TLID1007C Operate a forklift
Activity 10: Load centre distance The load centre distance, which is described on the manufacturer’s data plate is the distance between the centre of gravity of the load and the vertical face of the forks. Ask your trainer to explain this concept to you and to help you understand the concept, indicate on the diagram below t he load centre distance.
There is feedback on this activity at the back of this Learner’s Guide.
Page 36
© Australian National Training Authority 2003
TLID1007C Operate a forklift
How does load centre distance effect forklift stability? Astandardpalletissquareandhasthedimensions1200mmx1200mm asperthediagrambelow.
1200mm
1200mm
Asthemajorityofforkliftloadsarecontainedonpallets,forklift manufacturersdesignedtheforkliftwitha600mmloadcentre.This matcheswiththestandardstackedpalletcentreofgravity.For example,seediagram:
1200mm
600mm
Load centre
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 37 ADELG1011
TLID1007C Operate a forklift
Activity 11: How to calculate load centre and forklift capacity Discuss with either your trainer or a licensed forklift driver how to calculate the load centre of a forklift load and how the load centre affects the capacity of the forklift. Then answer the following questions: Question 1 What happens to the capacity of the forklift if the load has a load centre greater than 600mm? ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________
Page 38
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Question 2 Imagine that your forklift has the following specifications: •
Maximum safe working load or Capacity - 1000kg
•
Load Centre - 600mm
•
Max Height - 3500mm.
There are four different loads shown on the next page (drawings show side elevation). You are to determine and circle the loads which your forklift can safely lift. 900kg
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 39 ADELG1011
TLID1007C Operate a forklift
Question 3 If the load centre of the load is less l ess than 600mm, will you be able to carry more than the maximum safe working load? ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________
There is feedback on this activity at the back of this Learner’s Guide.
Page 40
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Forklift attachments Aforkliftattachmentisanextrapieceofequipmentthatisusedonthe forkliftinplaceoftheoriginalforks.Sometimestheforksareremoved andtheattachmentisboltedtotheforkcarriage,andsometimesthe attachmentisfittedtotheforks. Therearemanytypesofforkliftattachments.Somearestandardtype attachmentsandcanbepurchasedfromadealer,e.g.drumclamps. Othersarespeciallydesignedandmadetodoaspecifictask. Mostattachmentshavespecialsafetyconsiderationsthatyouneedto takeintoaccountwhenyoudrivetheforklift.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 41 ADELG1011
TLID1007C Operate a forklift
Activity 12: Forklift attachments Forklifts can be fitted with attachments that make them safer to handle certain loads. However, these forklift attachments change the way the forklift handles, therefore it is essential to know how the attachments are used and any safety considerations that you need to know. The worksheets on the following pages are designed to help you through this process. You can find out the answers to these questions by:
Page 42
•
discussing them with your trainer
•
discussing them with a work mate
•
discussing with a forklift sales person
•
studying books, magazines, brochures or posters.
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Drum clamp
What are drum clamps used for?
Drum clamps are used instead of transporting drums on pallets. Why?
Are they fixed to the forks or bolted on in place of the forks?
What are the safety considerations?
Roll clamps
What are roll clamps used for?
How do roll clamps work?
What are the safety considerations?
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 43 ADELG1011
TLID1007C Operate a forklift
Push-pull attachment
What are push-pull attachments used for?
How do push-pull attachments work?
What are the safety considerations?
Carpet spike
What are carpet spikes used for?
How do carpet spikes work?
What are the safety considerations?
Page 44
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Carton clamps
What are carton clamps used for?
How do carton clamps work?
What are the safety considerations?
Bale clamps
What are bale clamps used for?
How do bale clamps work?
What are the safety considerations?
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 45 ADELG1011
TLID1007C Operate a forklift
Rotators
What are rotators used for?
How do rotators work?
What are the safety considerations?
Pantograph
What are pantographs used for?
How do pantographs work?
What are the safety considerations?
Page 46
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Fork extensions
What are fork extensions used for?
How do fork extensions work?
What are the safety considerations?
Personnel lifts or work platforms
What are personnel lifts used for?
How do personnel lifts work?
What are the safety considerations?
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 47 ADELG1011
TLID1007C Operate a forklift
Jib
What is a jib attachment used for?
List other associated equipment that is commonly used with jib attachments.
What are safety considerations when using jibs?
Page 48
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 13: Jib equipment safety When using a jib, heavy items will be carried and suspended by slings. The slings and associated equipment equipment need to be thoroughly checked each time they are used to ensure it is safe to do so. There are also certain safety requirements r equirements and procedures that you need to know before using jibs and slings on a forklift. For instance, one of the main safety considerations for operators using jibs is the moving centre of gravity, therefore, extreme care needs to be taken when determining a safe working load for the forklift. Complete the worksheet on the next page, stating relevant safety requirements when using jibs on a forklift.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 49 ADELG1011
TLID1007C Operate a forklift
Equipment type
Safety considerations
Slings (draw an example of a sling in this space)
Hooks (draw an example of a hook in this space)
Rings (draw an example of a ring in this space)
Shackles (draw an example of a shackle in this space)
There is feedback on this activity at the back of this Learner’s Guide.
Page 50
© Australian National Training Authority 2003
TLID1007C Operate a forklift
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 51 ADELG1011
TLID1007C Operate a forklift
Section 3 Forklift safety
Page 52
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Section outline Areascoveredinthissection
Whattodobeforeyoudrivetheforklift Personalprotectiveclothing Forkliftsafetytips
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 53 ADELG1011
TLID1007C Operate a forklift
What is required for forklift safety? Themostimportantaspectofforkliftdrivingissafety.Asaforklift driveryoumustbeawarethattherearealwayspeopleworkingaround youandiftherewasanaccidenttheymaybeinjured.Itwouldbea terribleburdentohaveonyourconsciencethatyourworkmatewas injuredbyanaccidentthatyoucouldhaveprevented. ForkliftsafetyhasaveryhighprofileinAustraliaasstatisticsshow‘one intenworkplaceaccidentsinAustraliainvolvesaforklift’(1993).These accidentscanbepreventedonlyifcompaniesandindividualsrealise theimplicationsoftheseaccidentsandtakestepstopreventthem fromhappening.
Page 54
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 14: Before you drive the forklift Before you even consider driving the forklift, forklift , you need to complete three tasks. They are: •
plan your work - inspect the work area
•
select the correct forklift
•
make your presence known.
Complete the worksheet on the next page by explaining what is involved in these three steps.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 55 ADELG1011
TLID1007C Operate a forklift
Steps
Questions
Plan your work
Why do you need to plan your work?
Why do you need to inspect the work area?
What do you look for?
What do you do when a hazard or a risk has been identified?
Page 56
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Select the correct forklift
What do you need to consider when selecting a forklift to do a job?
Make your presence known
When do you need to let people know that you are about to drive a forklift in the area?
How can you alert people to the fact that a forklift is operating in the area?
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 57 ADELG1011
TLID1007C Operate a forklift
Personal protective clothing Thewearingofpersonalprotectiveclothingisanimportantfactorfor yourprotectionandisalegalOHSrequirement. Thetypesofpersonalprotectiveequipmentarevariedandtheiruseis determinedbythenatureofthetasksyouperform.Sometypesof personalprotectiveequipmentinclude:
Page 58
•
safetyhelmets
•
safetyglasses
•
safetybootsandshoes
•
gloves
•
aprons
•
overalls.
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 15: Personal protective clothing Different organisations have different personal protective clothing requirements for their forklift operators depending upon many factors. What protective clothing do you need to wear in your workplace while driving or inspecting the forklift? ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________
What protective clothing do you need to wear in a workplace while driving the forklift according to national and state regulations? ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 59 ADELG1011
TLID1007C Operate a forklift
What are some causes of forklift accidents? Therearemanytypesofaccidentsthatcanhappentoaforklift operatororworkmate.Themorecommoncausesofaccidentsare: •
beinghitbyamovingforklift,includingfeetbeingrunover
•
operatorbeinghitbyafallingobject
•
otheremployeesbeinghitbyafallingobject
•
boardingorleavingtheforklift
•
forklifttippingover
•
collisionwithothervehiclesorobjects
•
partsoftheoperator’sbodyprotrudingoutsideofthecab andstrikinganobject.
Therearealsomanysafetyrulesthatneedtobeobservedwhile drivingaforklift.
Page 60
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 16: Safety considerations Discuss forklift safety with any two of the following people: •
your trainer
•
a forklift trainer
•
an experienced forklift operator.
Then look through the list of forklift safety tips provided to you on the following pages. Then categorise each of the tips into the given headings on the page following these tips.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 61 ADELG1011
TLID1007C Operate a forklift
1
Know your forklift and ancillary equipment
2
Inspect prior to use
3
Report damage or faulty equipment immediately
4
Do not operate the forklift until faults are corrected
5
Do not make repairs, alterations or adjustments to any forklift unless authorised to do so
6
For forklifts powered by an electric motor, know the location of the emergency isolator and know how to operate it
7
Use the attachments and ancillary equipment only for its intended use
8
Do not use the forklift for any purpose other than what it is designed to do
9
Do not allow internal combustion engines to idle unnecessarily in an enclosed or semi-enclosed area
10
Know your loads and how to carry them properly
11
Carry only those loads that are rated within the capacity of the forklift
12
Handle only stable loads
13
Centre the weight of the load between the forks
14
Be aware of rear end swing
15
Ensure that the forks are fully inserted and the load is up against the fork back rest
16
Always travel with the forks no more than axle height
17
Know the load centre distance of the load - be especially careful when using attachments
18
Do not use supplementary counterweights to increase the capacity of the forklift
19
Always lift and lower the loads with the forks tilted slightly back
20
Tilt the elevated load forward only when directly over the unloading position
21
Watch floor strength everywhere especially on loading ramps and bridge plates
22
Ensure that you travel in the correct direction when driving up and down inclines
23
Avoid bumps, dirt, wet spots, rough ground or anything that may cause the forklift to become unstable
24
Check all bridge plates for width, capacity and security before driving on
25
Ensure that truck wheels are chocked before attempting to load via a bridge plate
26
Do not obstruct emergency exits, aisles or thoroughfares when either using or parking the forklift
27
Cross railway lines diagonally - railway lines should be recessed or chocks put in place
28
Know critical clearance areas and locations of overhead pipes, wiring, doorways, etc.
Page 62
© Australian National Training Authority 2003
TLID1007C Operate a forklift
29
Never turn on an incline or a slope
30
Never take or carry a passenger - no riders
31
Keep yourself and others clear of the lifting mechanism
32
Always travel with the fork tips pointed slightly up - even when unloaded
33
Report all accidents immediately
34
Keep all hands, legs, head, etc. inside the operator’s compartment
35
Use only secured, approved safety platforms when lifting personnel
36
Never allow anyone to go under the load or forks
37
Make sure that nobody stands or walks between the forklift and a stationary object
38
When leaving the forklift, ensure that it is in a parked condition - forks lowered, park brake on, power shut off, etc.
39
Always follow proper refuelling procedures
40
Always give way to pedestrians, ambulances or police
41
Safeguard pedestrians at all times
42
Always sound horn at cross aisles and blind corners
43
If forward visibility is obstructed, travel in reverse
44
Always clean up any spilled fuel, oil or flammable liquids before starting engine
45
Travel slowly around corners
46
If you cant see, don’t go
47
Always concentrate on the job at hand - never be distracted
48
Avoid sudden stops and starts
49
Always carry the load with the centre of gravity directly in the middle of the forks
50
Know what the common handling symbols mean
51
Never elevate loads while on an incline
52
Ensure that all tyre pressures are correct and the same
53
Use only electric forklifts in enclosed areas
54
Make sure that you travel slowly when you have a load
55
Do not wear rings, wrist watches, jewellery or metal objects when battery charging as these may contact the electrical parts and cause arcing
56
Take extreme care when loading and unloading containers - they are an enclosed area
57
Take extreme care when driving over wet surfaces. The braking distance will be considerably more
58
Never alter the forks in any way, shape or form
59
USE COMMON SENSE
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 63 ADELG1011
TLID1007C Operate a forklift
Place the number of the forklift safety tip next to the appropriate category. Driving the forklift e.g. 40 ________________________________________________________ ________________________________________________________________
Forklift and forklift equipment e.g. 52 ________________________________________________________ ________________________________________________________________
Forklift loads e.g. 12 ________________________________________________________ ________________________________________________________________
Workplace environment e.g. 21 ________________________________________________________ ________________________________________________________________
Personal safety e.g. 34 ________________________________________________________ ________________________________________________________________
Other peoples’ safety e.g. 30 ________________________________________________________ ________________________________________________________________
There is feedback on this activity at the back of this Learner’s Guide.
Page 64
© Australian National Training Authority 2003
TLID1007C Operate a forklift
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 65 ADELG1011
TLID1007C Operate a forklift
Section 4 Driving the forklift
Page 66
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Section outline Areascoveredinthissection
Pre-operationalsafetycheckofforklift Pre-operationalsafetycheckofworkarea Reportingofchecks Drivingtheforklift Drivingaloadedforklift Stackingandde-stacking Loadingandunloading Refuellingandrechargingaforklift
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 67 ADELG1011
TLID1007C Operate a forklift
Why are pre-operation safety checks completed? Beforeusinganyforkliftitisessentialthatyouconductapre-operation safetycheckonboththeforkliftandtheworksite. Thischeckistoensurethattheequipmentissafetouseandtheactual worksiteissafetoworkin. Notethatinrelationtothesafetycheckontheforklift: •
•
•
theextentofthesafetycheckwillbedeterminedby companyrequirementsandanyOHSregulations theremaybetheneedtocompleteachecklisttofulfil workplacepoliciesandregulationsbeforeusingthe equipment thecheckistoensurethattherearenofaultsordamage totheforkliftwhichmakeitunsafetooperate.
Notethatinrelationtothesafetycheckontheworksite: •
•
•
Page 68
thischeckistoensurethattheworksite(thepaththatyou willactuallybetakingwhenmovingtheload)isfreefrom obstaclesorsafetyhazards youshouldinformpeoplewhomaybeworkinginornear yourpath youshoulderectbarriersandsignstoinformotherpeople ofanypossibledanger(wherenecessary).
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 17: Pre-operational safety check equipment Watch your trainer or an experienced person demonstrate a preoperational safety check on the forklift. The pre-operational check will include a pre-start check and an operational check. The pre-start check is to check for safety features that can be checked before using the equipment; for example, flat tyres, worn slings, etc. The operational check is to determine if all forklift parts are working properly before using it on a job; for example, brakes, controls, etc. Whilst the person is performing the pre-operational safety check, ask them to tell you what they are checking so you can write it down to form a list. An activity worksheet is provided to help you and is located on the following pages. Decide if it is a pre-start check or an operational check and mark accordingly. Example: forklift (this example example is not complete)
Name of equipment
Forklift
Parts Checked - Pre start
Pre-start
Tyres for damage, pressure
✔
Wheel nut - not missing, tight
✔
Safety cage - damage, not loose
✔
Operational
Horn
✔
Park Brake
✔
Steering
✔
Etc. Etc.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 69 ADELG1011
TLID1007C Operate a forklift
Forklift Parts checked
Page 70
Pre-start
Operational
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Forklift Parts checked
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Pre-start
Operational
Page 71 ADELG1011
TLID1007C Operate a forklift
Activity 18: Check of work area Ask you trainer to give you an imaginary forklift task. Check out the work area where you would be using the forklift and identify any potential hazards or risk areas that might affect the safety of the operation. Write down areas that have potential hazards and any hazards or risks that you actually actually found. Then identify the actions that you would take (or actually took) to eliminate the hazard.
Hazard or risk
Action taken
Check out your answers with your trainer and then add any that you may have missed for future reference.
Page 72
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Reporting of pre-operation check results Onceaninspectioniscomplete,theresultsofthatinspectionneedto bereported.Manyworkplaceshaveastandardchecklistand procedureforthereportingofforkliftpre-operationalchecks.All employeeswhousetheforkliftusethisstandardprocedure. However,someworkplacesexpectyou,theemployee,tobe responsibleforthisprocess. OccupationalHealthandSafetyregulationsinsomeStates/Territories requirethatyoudoapre-operationalcheckbeforeyouusetheforklift andequipment.Theresultsthenneedtoberecordedandreported. Therefore,itmaybeyourresponsibilitytodothis.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 73 ADELG1011
TLID1007C Operate a forklift
Activity 19: Pre-operational checklist First, find out if your workplace has a standard procedure for conducting the pre-operational check and for recording and reporting the results. If so, obtain a copy of the relevant documentation for your reference and use. If not, study the pre-operational checklist on the next page. Once completed, show the checklist to your trainer tr ainer and discuss what items need to be checked and if your organisation has any other requirements that you need to complete.
Page 74
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Pre-operational checklist for counterbalanced forklift
Pre-start check - outside visual
Pre-start check - inside engine compartment
No leaks or obstructions under forklift
Liquid levels correct - engine oil, hydraulic oil, brake fluid, cooling water, transmission oil
Tyres - not flat, not damaged, wheel nuts not loose, tyre pressure
Fan belt - correct tension
Mast assembly - damage, obstructions, lubrication, chain tension
Battery - water level, connections and security
Forks/attachments - condition, secure, locking pins secure
Battery (electric forklifts) - sufficient charge, water levels
Load backrest -secure, not damaged
Condition - any leaks, damage or obstructions
Hydraulic hoses and couplings excessive leaking, not damaged Body damage
Operational Check
Safety cage secure
Gauges and warning lights - working
Check steering wheels and cylinders
Lights - check if working
Check for any loose wiring
Warning signals - revolving light, reverse beeper, indicators
Towing pin secure
Horn
Check manufacturers data plate
Mast controls
Driver compartment - free from obstacles, adjust seat, adjust mirrors
Park brake
Gas - turn on, check fittings secure, check for leaks, check level of gas
Foot brake
Steering
Name ________________________ ________________________
Signature _______________ ________________ _ Date _____________ _____________
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 75 ADELG1011
TLID1007C Operate a forklift
Activity 20: Using the checklist Using your workplace checklist or the checklist shown on the previous page, practise using the list by checking the forklift and recording and reporting the results. Then report the results of the pre-operational check according to your workplace procedures. NOTE: Your state/territory legislation legislation may require you to be licensed before you you can use a forklift. If this applies in your your state/territory you will need to be supervised when conducting the operational check as this involves operating the forklift.
Page 76
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Forklift start-up procedure Thispartoftheunitdealswiththeoperationoftheforklift.It isessentialthatyouoperatetheforkliftundersupervision whilstyouareintraining. Failuretodosowillhavebothyouandyouremployerliablein theeventofanaccident.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 77 ADELG1011
TLID1007C Operate a forklift
Activity 21: forklift start-up procedure The forklift start-up procedure is similar to the start-up procedure of a car. There is a definite definite procedure to follow to ensure that everybody is safe and the equipment is safe to operate. Think about the procedure you are supposed to follow when you first get into a car and start the engine. Now relate this to the forklift. List the first five steps you would take when you get into a forklift. a. b. c. d. e.
Page 78
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Travelling and parking the forklift Theforkliftcontrolsaredifferentfromthoseofacarormotorbikein thattheyonlyhaveoneforwardandonereversegear.Theyhaveno clutchbuttheydohaveabrakeandanaccelerator. Tooperatetheforklift,followthegivensequence: •
releasetheparkbrake
•
movethedirectionleverinthedirectionyouwishtotravel
•
takeyourfootoffthefootbrake
•
presstheacceleratorslowlyuntilmovementoccurs
•
adjusttheacceleratortothedesiredspeed.
Steering Theforkliftisdifferentfrommostothervehiclesinthatitissteeredby thebackwheelsandpoweredbythefrontwheels.Insteadofthe vehiclefollowingthefrontwheelsaroundacorner(asacardoes),the backoftheforkliftwillswingout,therebyturningthevehicle.Thisis commonlycalled‘TailSwing’.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 79 ADELG1011
TLID1007C Operate a forklift
Activity 22: Tail swing The tail swing of the forklift occurs whenever the forklift is turned around a corner and is one of the main skills that you, as a forklift driver, need to master if you wish to become a competent forklift driver. Why do you think the forklift is designed and built with rear wheel steering? ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________
Page 80
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Whenyoufirststartdrivingtheforkliftyouwillbeshownwherethe pivotpointisontheforklift.Thepivotpointisanimaginarypoint wheretheforkliftpivotswhilstturningacorner.Theforkliftisnotlike acarwhereaturningcircleisrequiredasaforkliftcanvirtuallyturnon apoint. Itisessentialtoknowwherethepivotpointoftheforkliftissothat youareabletomanoeuvreinverysmallspaces.Itdiffersslightly betweenforklifts. Youwilllearnmuchmoreaboutdrivingtheforkliftwhenyoubegin yourpracticaldrivingpartoftheunit. Whendrivingaforkliftyoumustalwaysbeconsciousofthesafety factor.Therearemanyrulesandsafetyprecautionsthatyoumust followwhenyouareinchargeoftheforklift.
Stopping and parking the forklift Manyaccidentscanoccurwhentheforkliftisbeingbroughttoahalt. Forkliftsshouldbebroughttoahaltgraduallyaswheelslidingand hardbrakingisdangerous,unnecessaryandharmfultotheforklift truck. Ifhardbrakingoccursthereisaveryhighpossibilityoftheloadtipping over,therebydamagingstock,wastingtimeandpossiblycausinginjury tosomebody. Afteryouhavebroughttheforklifttoahalt,itneedstobeparked correctly.Thecorrectparkingprocedureis: •
•
ensurethattheforkliftparkingpositionissuitable-e.g. not infrontofexits,levelground,notinwalkways makesurethatthetipsoftheforksaretouchingthe groundby: − tiltingthemastslightlyforward − loweringtheforksuntilthetipsaretouchingtheground
•
puttheforkliftinNEUTRAL
•
applytheparkingbrake
•
turnofftheforkliftandremovethekey(accordingtoyour companypolicy)
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 81 ADELG1011
TLID1007C Operate a forklift
•
Page 82
turnoffgas(ifgaspowered).
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 23: Shut down Answer the following questions. Why is it important to have the fork tips touching the ground? ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________
Why do you think this is necessary to conduct a post-operational check on the forklift? ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________
List the items that you think you would need to look at in the postoperational check. ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 83 ADELG1011
TLID1007C Operate a forklift
If you found a fault in conducting the post-operational check what do you need to do? ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________
Page 84
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Refuelling/recharging Refuelling/rechargin g the forklift Aspartofyourdrivingskillsyouwillobviouslyneedtoknowhowto refueltheforklift. Itisimportanttofollowspecificinstructionswhenrefuellingthe forklift.Althoughtherearedifferentfuelsforforkliftsandtherefore differentrefuellingmethodsthefollowingrulesapplytoallforklifts whenrefuelling. Rules •
•
•
•
Beforerefuellingshutofftheengineandthelightsanddo notrestartengineuntilrefuellinghasfinished. Smokingisprohibitedinanyareawherethetruckisbeing refuelled. Refuellingshouldbedonewellawayfromwelding,open flamesandsparks. Ifyoudetectafuelleak,don’tstarttheforklift,pullit outsideandaskforhelp(fromyourtrainer,supervisoror maintenance).
WithLPGtherefuellingprocessinvolveschangingoveragasbottle, notsimplyfillingupthetankaswedowithmotorvehicles. ThefollowingprocedureshouldbefollowedwhenreplacingtheLPG gascylinderontheforklift. Beforechangeover •
•
•
•
Smokingisprohibitedinanyareawherethetruckisbeing refuelled. Keeptheenginerunning. Closethecylindershutoffvalveandlettheenginerun untilitstops. Whilechangingovercylinderalwayswearglovesanduse eyeprotection.
Conductingchangeover •
•
•
Unscrewthebottlefittingmakingsurethatyouare wearinggloves Removethecylinderandstoreemptycylinderuprightin thedesignatedarea(mustbeundercover). Connectupthenewcylinder.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 85 ADELG1011
TLID1007C Operate a forklift
Afterchangeover •
•
Startforkliftandcontinuework. Ifaleakisdetectedinthefuelsystem,stopimmediately, turnoffisolatorvalve,putanappropriatesignonforklift andreportleaktosupervisor.
Batterycharging
Ifyouhaveanelectricforkliftyouwillobviouslyhavetorechargethe batteryratherthanrefueltheforklift. Whentheforkliftneedsit'sbatterychanged,theforkliftmustbe stationaryandmovedsothatitisintheproperparkedposition. Batteriesshouldbechargedinadesignatedareathatisfreefrom obstacles,weldingequipment,sparksandopenflames.Itshouldalso haveproperventilationasbatteriesduringcharginggiveoffhydrogen gasthatisextremelyflammable.Theareashouldalsobeanonsmokingasacigarettecouldcauseanexplosion. Tipsonbatterycharging •
•
•
•
•
•
•
Page 86
Parktheforkliftinthedesignatedareaandensurethe handbrakeison. Smokingisprohibitedinanyareawherethebatteryis beingrecharged. Openthebatterycompartmentandleavethisopenduring chargingoperation. Ensureventcapsarefunctioningproperlyandleavevent capsinplacetoavoidelectrolytespray. Donotwearrings,wristwatches,jewellery,orothermetal objectsastheymaycontactelectricalpartswhichwill causearcingandelectrocution. Keepallmetallicobjectsawayfromthetopofthebattery asthesemayalsocausearcing. Ifanyleakageofthebatteryelectrolyteoccursthenflushit away;reportanymajorspillage.
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 24: Battery charging Thefollowingdiagramshowsaforkliftdriverinvolvedinmanyunsafe practises.Listtheunsafepractisesthatyoucanidentify.
________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 87 ADELG1011
TLID1007C Operate a forklift
Loading and stacking Loadingandstackingisagainaverypracticalskillandwillneedtobe learntatyourpracticalsessions.Howeverthereissometheorythat youcanlearnbeforeyoudrivetheforklift. Asaforkliftdriver,youwilllift,stack,de-stackandmoveloadsevery dayandsotheseskillswillbecomesecondnaturetoyouintimeand withpractice.
Page 88
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 25: Lifting and carrying The following exercise lists the correct procedures for lifting and carrying a load. Fill in the missing words 1. Approach the load load ................ making sure that the forklift is square to the load and the forks are ...................... and at the correct height for sliding under the load. 2. Move forward slowly until the forks are entirely under the load and the load is ................... .............. ..... against the fork backrest. Ensure that the load is .................... ............. ....... and take care to ensure that the forks do not ..................... past the back of the load.
3. Raise the load until all .......................... are cleared. ............ the load backwards to ensure safe handling of the load. 4. To transport the load, the mast needs to be tilted slightly ..................... ....... to ensure ensure that the load is stable. Do not travel with the load raised higher than .......................... for adequate clearance. clearance. This is generally generally no higher higher than ...............
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 89 ADELG1011
TLID1007C Operate a forklift
5. To unload, first the load needs to be .................. slightly ..................... .... then lowered to the ground. It may then be necessary to tilt the mast further ....................... to ensure that the forks are smoothly withdrawn from the load.
6. ................. .... back away from the load ensuring that the forks do not catch on the load.
There is feedback on this activity at the back of this Learner’s Guide.
Page 90
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Stacking a load Thefollowingisthecorrectproceduretousewhenstackingand unstackingaloadofpallets.Youshouldfollowthisprocedureatall times: •
Approachthestackwiththeloaddownandtilted backwards.
•
Haltatthebaseofthestackbyapplyingbrakes.
•
Raisetheloadtothedesiredstackingheight.
•
Driveforwarduntiltheloadisoverthestack.
•
Tiltmasttoaverticalposition.
•
Lowertheloadontothestack.
•
•
•
Whentheloadisstackedsecurely,lowertheforkarms untilfreeofthepallets. Movethetruckbackwardsmakingsurethattheforksare clearofthepallets.(Note:Itmaybebeneficialtotiltthe forksforwardasthetruckismovedbackwards). Whentheforksareclearofthestack,lowertheforksand tiltslightlybackwards.
De-stackingaload •
•
Haltatthebaseofthestack-remembertoensurethatthe loadiswithincapacityoftheforklift. Raisetheforkstothedesiredheight.Asyoudosotilt mastuntilitisvertical.
•
Insertforkstotheirfullextentbydrivingforward.
•
Liftloadclearofstackandcarefullyapplybackwardstilt.
•
•
Whentheloadisclearofthestack,movebackslowlyuntil itisclear-(remembertolook). Lowertheloadcarefullyandsmoothlytotravellingheight, applyfurtherbackwardtiltbeforemoving.
Reachtruckstacking
Thestackingandde-stackingwithareachtruckisthesameasa counterbalancetruckexceptthatthereachtruckhastheoptionto movetheforksforwardtopickandplacetheload.Thisensuresthat thereachtruckismorecompactandabletomoveinsmallerspaces.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 91 ADELG1011
TLID1007C Operate a forklift
Remembertoalwaysbringtheloadwithinthewheelconfinesbefore movingtheload.
Loading and unloading vehicles Whenloadingvehiclesthefirstprioritywithanyloadistokeepthe loadwithinthelegalaxleloadrequirementsandwithinthepermissible loaddimensions. Tobeabletodothisyouneedtobeabletounderstandsome‘truckie’ terms. The‘truckie’termsthatyouwillneedtounderstandare: •
•
•
TARE-themass(weight)ofthevehiclewithoutitsload AGGREGATEMASS-themaximumallowableloadedmass ofaparticularvehicle GROSSCOMBINATIONMASS-theloadedmassofthe vehicleplustheaxleloadsofanytrailerbeingtowed (includessemitrailers).
Whenloadingvehiclesitisessentialtodistributetheloadtokeepthe centreofgravityaslowaspossibleandthevehicleevenlybalanced.If possible,itemsshouldbeplacedagainsttheheadboardofthevehicle sothattheycanbesecuredproperlyandtheyareinnodangerof movingduringbraking. Larger,heavieritemsshouldbeplacedatthebottomoftheload.The vehicleshouldbeloadedtogiveanevenweightdistributionoverits floorarea.Thismayrequirepackingsuchastimberplanksorblock wedges. Trytoalwaysdistributetheloadsothatlightcrushableobjectsarenot loadedinfrontoftheheavierlargeobjectsotherwisetheymightbe squashedduringbraking.Heavysoliditemsshouldalsobeloadedso thatpartoftheitemisovertheregionoftheaxles.Thiswillhelp distributetheloadevenly. Ifhighloadsneedtobetransportedalwaystrytouselowplatform vehiclesashighloadswillseriouslyaffectthecentreofgravityofthe loadandputitinseriousdangerofoverturningwhencornering.
Page 92
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 26: Loading trucks In the following exercise exercise an empty truck is drawn. There are also some loads on the ground next to the truck. Using these loads loads draw them onto the truck as it should be loaded according to the appropriate safety rules.
There is feed Learner’s Gui
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 93 ADELG1011
TLID1007C Operate a forklift
Activity 27: Driving the forklift During this activity you will be required to practise using the forklift within a variety of workplace situations. This activity must be done so under supervision according to any regulations or workplace and equipment policies. This activity only allows you to practise using the equipment. There will be separate assessment exercises that you need to complete. Your trainer will give you you different workplace tasks to do. They must include: •
using the forklift unloaded
•
using the forklift with a variety of loads l oads
•
using the forklift with long, wide loads
•
loading and unloading a truck
•
stack and de-stack a load (low and high stacks) in both narrow and wide aisles.
Each time you use the equipment, fill in the logbook contained in the Assessment Tasks section of this Learner’s Guide. Once you feel that you are competent in the use of this equipment in all of the above tasks, approach your trainer and request an assessment.
Page 94
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Additional resources
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 95 ADELG1011
TLID1007C Operate a forklift
Websites:
• Workcover Authority of NSW http://www.workcover.nsw.gov.au/
• WorkSafe Victor http://www.workcover.vic.gov.au/wps/wcm/connect/WorkSafe
• WorkCoverQueensland http://www.workcover.qld.gov.au/
• WorkCover WA http://www.workcover.wa.gov.au/
• WorkCover SA http://www.workcover.com/home.aspx
• ACT WorkCover http://www.workcover.act.gov.au/
• WorkplaceStandardsTasmania http://www.wst.tas.gov.au/node/WST.htm
• NTWorkSafe http://www.worksafe.nt.gov.au/
Page 96
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Feedback on activities The responses provided in this section are suggested responses. Because every workplace is different, your responses may vary according to your specific workplace procedures, the equipment available and the nature of the business.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 97 ADELG1011
TLID1007C Operate a forklift
Activity 4: Identification of the different types of forklifts There are four main types of forklifts that you are likely to see within the road transport industry. These are discussed below:
Counterbalance forklift What does a counterbalance forklift look like? (draw or find a picture and place in the space opposite)
Page 98
Why is it called a ‘counter balance’ forklift?
Because the load being picked up is counter balanced by the weight of the vehicle chassis, engine, counterweight and body
Where is the balance point or fulcrum of a counterbalance forklift found?
A point on the ground vertically below the front axle
List the two main power source options that you find on counterbalanced forklifts.
internal combustion engine electric powered - battery
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Straddle forklift or reach truck What does a straddle forklift look like? (draw or find a picture and place in the space opposite)
How is the weight of the load distributed on a straddle forklift?
The weight of the load is distributed between the four wheels of the forklift while moving. This dismisses the need for the forklift to counterbalance any load.
What is a straddle forklift primarily designed for?
The straddle forklift is primarily designed for use in the warehouse. They are designed to be manoeuvrable and to lift pallet loads to great heights.
What is the primary power source for straddle forklifts?
Most straddle forklifts are electric powered.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 99 ADELG1011
TLID1007C Operate a forklift
Order pickers What does an order picking forklift look like? (draw or find a picture and place in the space opposite)
Why is it called an ‘order picker’?
It is called an order picker because that is its primary use. To lift the operator to high levels where he/she can select stock for picking a customers order.
What is the difference between an order picker and a straddle forklift?
The order picker and the straddle are quite similar in their looks but with an order picker the operator and the forklift controls are actually lifted to the desired height. With a straddle forklift it is only the load which is lifted to the desired height.
Page 100
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Side loading forklift What does a side loading forklift look like? (draw or find a picture and place in the space opposite)
Why is it called a ‘side loading’ forklift?
Because unlike other forklifts the load is picked up from the side of the forklift rather than the front. This allows the forklift to be manoeuvrable with long awkward loads.
What types of loads are handled by the side loading forklift?
Usually long loads such as timber, pipes, metal bars, containers.
Give two examples of Timber yards, timber merchants. workplaces that Steel and pipe retailers. might use the side loading forklift? Anyone who moves long loads of timber, steel, plastic. Container storage areas.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 101 ADELG1011
TLID1007C Operate a forklift
Activity 5: Advantages and disadvantages of electric powered forklifts
Advantages of electric powered forklifts
Disadvantages of electric powered forklifts
No exhaust fumes emitted, therefore suitable for enclosed spaces, cool rooms, warehouses, etc.
Batteries are bulky, very heavy and very expensive.
Very little engine noise. Virtually no vibration. Ongoing maintenance costs seem to be less than internal combustion.
The actual forklift is usually more expensive than an internal combustion forklift. Battery takes quite a few hours to recharge therefore there is either the need for an extra battery or a long wait between forklift use. Extra cost of battery recharging equipment.
Cost saving on fuel.
Less power than internal combustion. Relatively short operating time between recharges.
Activity 6: forklift components Component Overhead guard Steering wheels Load Backrest Forks Mast Drive wheels Counter weight Hoist chains Manufacturer’s data plate Parking brake
Page 102
No. 3 6 10 9 2 8 4 1 7 5
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 8: Data plate information Complete the chart by completing the definition and then selecting one of your workplace forklifts and give actual data plate readings.
Information
Definition
Load centre distance
The distance between the centre of gravity of the load and the vertical face of the forks on the forklift. This is usually 600mm but may be 500mm on some forklifts.
Maximum safe working load
The maximum weight the forklift can safely carry.
Maximum lift height
The maximum height that the forklift can lift the maximum safe working load.
Mast tilt - degrees
The amount of forward and reverse tilt in the mast. The figure is in degrees. For example, 6 degrees.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Data plate information
Page 103 ADELG1011
TLID1007C Operate a forklift
Activity 9: Centre of gravity Indicate where the centre of gravity is on the following shapes:
Centre of Gravity 1200mm 2.1m 600mm 700mm 900mm 1800mm 600mm
1.8m 800mm diameter
Dead centre
1.5m
1.25m
0.75m
2.5m
Page 104
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 10: Load centre distance The load centre distance, which is described on the manufacturer’s data plate is the distance between the centre of gravity of the load and the vertical face of the forks. Centre of Gravity of the load
Load backrest
Load centre distance
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 105 ADELG1011
TLID1007C Operate a forklift
Activity 11: How to calculate load centre and forklift capacity Question 1 What happens to the capacity of the forklift if the load has a l oad centre greater than 600mm? If the load centre distance is greater than 600mm, the capacity of the forklift (the weight that it can carry) carry) will decrease. When the load centre is more than 600mm this will cause an effect where the load will appear heavier than what it actually is. Question 2 Imagine that your forklift has the following specifications Capacity - 1000kg Load centre - 600mm Max height - 3500mm There are four different different loads shown below. below. You are to determine determine which of the loads loads can be safely safely lifted with your forklift. Circle the loads that can be safely lifted.
900kg
Question 3 If the load centre of the load is less l ess than 600mm, will you be able to carry more than the maximum safe working load? No - The maximum weight at any time is the maximum safe working load.
Page 106
© Australian National Training Authority 2003
TLID1007C Operate a forklift
Activity 13: Jib equipment safety
Equipment type
Safety considerations
Slings
There are many different types of slings - wire rope, chain, webbing, natural fibre & synthetic. Check slings every time you use it - check for excessive wear, broken fibres or wires, weathering, mould, rot or sun damage, rust or cracks, cuts or gouges and stretching or bending of links. Ensure that the SWL (Safe working load) of the sling is never exceeded. All slings must have a label indicating either the SWL or the WLL (working load limit) - if the label is missing do not use the sling.
Hooks
Many different types. Ensure that it is an approved type of hook - never homemade. Ensure correct SWL - ensure that it is the same or less than the sling. Hooks used with jib attachments must always be the swivelling type - never the fixed type. Discard if more than 10% wear is evident.
Rings
Many different types. Ensure that it is an approved type of shackle - never homemade. Ensure correct SWL - ensure that it is the same or less than the sling. Discard if more than 10% wear is evident.
Shackles
Many different types. Ensure that it is an approved type of ring - never homemade. Ensure correct SWL - ensure that it is the same or less than the sling. Discard if more than 10% wear is evident.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 107 ADELG1011
TLID1007C Operate a forklift
Activity 16: Safety considerations Driving the forklift
14,16,19,20,22,29,32,40,43,45,46,4 14,16,19,20,22,29,32,40,43,45,46,4 8, 51,54,59
Forklift and forklift equipment
1,5,6,7,18,52,58
Forklift loads
10,11,12,13,15,17,49,50,
Workplace environment
21,23,24,25,27,28,56,57
Personal Safety
2,3,4,8,31,33,34,39,44, 47,55,
Other peoples safety
9,26,30,35,36,37,38,41,42,53,
Note: many of these safety tips could be be grouped into a different category. The answers shown shown above are one option only. only.
Activity 25: Lifting and carrying 1. Approach the load slowly making sure that the forklift is square to the load and the forks are level and at the correct height for sliding under the load. 2. Move forward slowly until the forks are entirely under the load and the load is resting against the the fork backrest. Ensure that the load is centred and take care to ensure that the forks do not protrude past the back of the load. 3. Raise the load until all obstacles are cleared. Tilt the load backwards to ensure safe handling of the load. 4. To transport transport the load, load, the mast needs needs to be tilted slightly backwards to ensure that that the load is stable. Do not travel travel with the load raised higher than necessary for adequate clearance. This is generally no higher than 150mm (axle height). height). 5. To unload, first the load needs to be tilted slightly forward then lowered to the ground. ground. It may then be necessary to tilt the mast further forward further forward to ensure that the forks are smoothly withdrawn from the load.
Page 108
© Australian National Training Authority 2003
TLID1007C Operate a forklift
6. Slowly back away from the load ensuring that the forks do not catch on the load.
Activity 26: Loading trucks
Note: There are numerous numerous ways in which which the truck may may be loaded using these these loads. loads. This is one example. example. If your answer differs from the one shown above, consult your trainer to ensure that your answer is correct.
© Australian National Training Authority 2003 Customised and Developed by Armstrong’s Driver Education July 2009
Page 109 ADELG1011