A laboratory report for a sand casting experimentDescripción completa
example of lab report for sand patch testFull description
document 1Full description
project report of sand muller for mechanical engineering studentsFull description
This is a lab report on Sand Replacement Method done in Geotechnical Engineering
Silt Excluder
an information paper
silt
chemistry experimentFull description
Descripción: For Diploma Sains only
For Diploma Sains onlyFull description
EMC Test Report for CE CertificationFull description
Full description
M sand
Full description
Pengujian Sand Cone
Full description
CONTENT
NO
TITLE
PAGE
1
OBJECTIVE
1
2
THEORY
1
3
APPARATUS
2
4
MATERIAL
2
5
PROCEDURES
3
6
RESULT
4
7
QUESTIONS
5
8
DISCUSSION
6
9
CONCLUSION
7
10
APPENDIX
8
11
REFERENCE
9
0|Page
EXPERIMENT
:4
TITLE
: SILT TEST FOR SAND
OBJECTIVE
: To determine amount and percent of silt in a nature sand
THEORY
Silt is granular material of a size somewhere between sand and clay whose mineral origin is quartz and feldspar. Silt may occur as a soil or as suspended sediment (also known as suspended load) in a surface water body. It may also exist as soil deposited at the bottom of a water body.
Clay, mud, fine, dust or silt will weaken the concrete because the dirt tends to coat the aggregate and weaken the bond between the aggregate and cement paste thus preventing the cement from setting. Coarse aggregates should be for cleanliness purposes are inspected by visual inspection.
1|Page
APPARATUS
1. Measuring cylinder 250 ml 2. Rubber hammer 3. Spatula 4. Stirring rod
MATERIAL
1. Water 2. Sand 3. Salt
2|Page
PROCEDURE
1. The cylinder was filled up to about 50 ml of salt water solution. (one tablespoon salt to 1 litre of water) 2. The sand was poured into the cylinder until the level of water reaches 100 ml. 3. More salt water was added until it reaches 150 ml. 4. The cylinders were shakes well. 5. The cylinders were placed on a levelled surface. 6. After 2 hours, the results were recorded. 7. The silt layer was measured on top of the sand. The thickness can be explained as a percentage of sand level below the layer. The sand considered as clean if the percentage is not more than 8% of the original volume of the sand.
3|Page
RESULT
Calculation on amount of silt using Volume method. Measurement (mm) No.
Description
1
2
Percentage of silt in sand
=
Sand inside the lab
Sand outside the lab
Height of sand layer (y)
83 mm
80 mm
Height of silt (x)
4 mm
5 mm
x / y X 100%
=
Standard form
:
percentage of silt less than ………………………………….%
4|Page
QUESTION 1.
Why we use salt water in this test?
We use the salt in this test is for separate the water with the sand to measure the silt layer on the top of the sand. If we don’t use the s alt, we could not measure it as the water did not float or separate with the sand. 2.
What happen to you concrete when we use the sand with silt more than 8%?
If we use sand with silt more than 8%, the concrete will weak and cannot use it for any project. This is because the silt will weaken the bond between aggregates and cement paste.
5|Page
DISSCUSSION
Silt is created by a variety of physical processes capable of splitting the generally sand-sized quartz crystals of primary rocks by exploiting deficiencies in their lattice. These involve chemical weathering of rock and regulate, and a number of physical weathering processes such as frost shattering and haloclasty. The main process is abrasion through transport, including fluvial combinations, Aeolian attrition and glacial grinding. It is in semi-arid environments that substantial quantities of silt are produced. Silt is sometimes known as "rock flour" or "stone dust", especially when produced by glacial action. Mineralogical, silt is composed mainly of quartz and feldspar. Sedimentary rock composed mainly of silt is known as siltstone.
6|Page
CONCLUSION
If the sand contains more than 6% silt, you would have to use more cement and the concrete would shrink more during the hardening process, causing cracks in the product. Silt and clay are not as strong as typical aggregates. They can absorb water and their properties can change because of it. In fresh concrete, I would think that silt and clay would interfere with the bonding of aggregates to cement. In hardened concrete, if the silt and clay come in contact with water in air voids, they can shrink or swell, either building internal pressure (swelling) or leaving larger voids and weakening the concrete (shrinking).
