BTS3900 Technical Description

BTS3900 GSM V300R009

Technical Description

Issue Date

06

2010-05-10

Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

Huawei Technologies Technologies Co., Ltd. provides customers with comprehensive comprehensive technical support and service. For any assistance, please contact our local office or company headquarters. headquarters.

Huawei Technologies Co., Ltd. Address:

Huawei Industrial Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China

Website: Email:

http://www.huawei.com [email protected]

Copyright © Huawei Technologies Co., Ltd. 2010. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions and other Huawei trademarks are the property of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned mentioned in this document are the property of of their respective respective holders. holders.

Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations recommendations in this document do not constitute the warranty of any kind, express or implied.


Huawei Technologies Technologies Co., Ltd. provides customers with comprehensive comprehensive technical support and service. For any assistance, please contact our local office or company headquarters. headquarters.

Huawei Technologies Co., Ltd. Address:

Huawei Industrial Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China

Website: Email:

http://www.huawei.com [email protected]

Copyright © Huawei Technologies Co., Ltd. 2010. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions and other Huawei trademarks are the property of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned mentioned in this document are the property of of their respective respective holders. holders.

Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations recommendations in this document do not constitute the warranty of any kind, express or implied.


BTS3900 GSM Technical Description

Contents

Contents About This Document...................... Document....................................................................... ...............................................................................................1 ..............................................1 1 Changes in BTS3900 GSM Technical Description..............................................................1-1 2 System Architecture of the BTS3900......................................................................................2-1 3 Logical Structure of the BTS3900............................................................................................3-1 BTS3900............................................................................................3-1 4 BTS3900 Monitoring System.............................. System............................................................................. ...................................................................... .......................4-1 4-1 5 Reference Clocks of the BTS3900/BTS39 BTS3900/BTS3900A........................................................................ 00A........................................................................5-1 5-1 6 Signal Flow of the BTS3900/BTS3900A.................................................................................6-1 7 Topologies of the BTS............................. BTS................................................................. ......................................................................... ..............................................7-1 .........7-1 8 Surge Protection Protecti on Specifications of the BTS3900..................................................................8-1 9 Configuration of Configuration of the BTS3900/BTS3900A.............................................................................9-1 BTS3900/BTS3900A.............................................................................9-1 9.1 BTS3900/BTS3900A BTS3900/BTS3900A Configuration Principles..............................................................................................9-2 9.2 RF Cable Connections of the DRFUs.............................................................................................................9-8 9.3 RF Cable RF Cable Connections of the GRFUs...........................................................................................................9-19 9.4 RF Cable RF Cable Connections for the Coexistence of the DRFUs and GRFUs.......................................................9-22 9.5 CPRI CPRI Cable Connections of the RFUs..........................................................................................................9-25

Issue 06 (2010-05-10)


i


Figures

Figures Figure 2-1 BTS3900 system.................................................................................................................................2-1 Figure 3-1 Logical structure of the BTS3900......................................................................................................3-1 Figure 4-1 Monitoring ports of the BBU..............................................................................................................4-1 Figure 4-2 Components of the monitoring system...............................................................................................4-2 Figure 6-1 DL traffic signal flow.........................................................................................................................6-1 Figure 6-2 UL traffic signal flow.........................................................................................................................6-2 Figure 6-3 Signaling flow.....................................................................................................................................6-3 Figure 6-4 DL traffic signal flow.........................................................................................................................6-4 Figure 6-5 UL traffic signal flow.........................................................................................................................6-5 Figure 6-6 Signaling flow of signaling processing..............................................................................................6-6 Figure 6-7 DL traffic signal flow.........................................................................................................................6-7 Figure 6-8 UL traffic signal flow.........................................................................................................................6-8 Figure 6-9 Signaling flow of signaling processing..............................................................................................6-9 Figure 7-1 Star topology.......................................................................................................................................7-1 Figure 7-2 Chain topology...................................................................................................................................7-1 Figure 7-3 Tr ee topology......................................................................................................................................7-2 Figure 7-4 Ring topology.....................................................................................................................................7-2 Figure 7-5 Regrouping for disconnection in the ring topology............................................................................7-4 Figure 7-6 Layer-2 networking topology.............................................................................................................7-4 Figure 7-7 Layer-3 networking topology.............................................................................................................7-4 Figure 7-8 Star topology.......................................................................................................................................7-5 Figure 7-9 Chain topology...................................................................................................................................7-5 Figure 7-10 R ing topology...................................................................................................................................7-5 Figure 9-1 BBU slots............................................................................................................................................9-7 Figure 9-2 Mapping between the RF cables and their colors...............................................................................9-8 Figure 9-3 R F cable connections of S1 (Transmit Independency or Combining/transmit diversity)/S2 (Transmit Independency or Combining)..............................................................................................................................9-10 Figure 9-4 R F cable connections of the DRFU with Transmit Independency or Combining............................9-11 Figure 9-5 R F cable connections of S2 (PBT)/S3 (Transmit Independency or Combining)/S4 (Transmit Independency or Combining)..............................................................................................................................9-13 Figure 9-6 RF cable connections of S3/3 configured with three DRFUs...........................................................9-14 Figure 9-7 RF cable connections of S2 with 4-way RX diversity......................................................................9-15 Figure 9-8 RF cable connections of S2 (transmit diversity)/S4 (transmit independency).................................9-16

Issue 06 (2010-05-10)


iii


Figures

Figure 9-9 RF cable connections of S5 (Transmit Independency or Combining)/S6 (Transmit Independency or Combining)..........................................................................................................................................................9-18 Figure 9-10 RF cable connections of S7 (Transmit Independency or Combining)/S8 (Transmit Independency or Combining)..........................................................................................................................................................9-19 Figure 9-11 Mapping between the RF signal cables and their colors................................................................9-19 Figure 9-12 RF cable connections (1)................................................................................................................9-20 Figure 9-13 RF cable connections (2)................................................................................................................9-21 Figure 9-14 RF cable connections (3)................................................................................................................9-22 Figure 9-15 Mapping between the RF cables and their colors...........................................................................9-22 Figure 9-16 RF cable connections (1)................................................................................................................9-23 Figure 9-17 RF cable connections (2)................................................................................................................9-24 Figure 9-18 RF cable connections (3)................................................................................................................9-25 Figure 9-19 Typical topology of the DRFUs.....................................................................................................9-26 Figure 9-20 Typical topology of the GRFUs.....................................................................................................9-26

iv


Issue 06 (2010-05-10)


Tables

Tables Table 4-1 Monitoring modules of the BTS3900..................................................................................................4-2 Table 4-2 Functions of the BTS3900 monitoring system.....................................................................................4-3 Table 7-1 Comparison of topologies....................................................................................................................7-3 Table 8-1 Surge protection specifications of the BTS3900..................................................................................8-1 Table 9-1 RF configuration principles of the BTS3900.......................................................................................9-3 Table 9-2 Board configuration principles of the BBU.........................................................................................9-8 Table 9-3 Configuration description (1)...............................................................................................................9-9 Table 9-4 Configuration description (2).............................................................................................................9-12 Table 9-5 Configuration description (3).............................................................................................................9-13 Table 9-6 Configuration description (4).............................................................................................................9-15 Table 9-7 Configuration description (5).............................................................................................................9-17 Table 9-8 Configuration description (6).............................................................................................................9-18 Table 9-9 Typical configurations of the sending receiving mode......................................................................9-20 Table 9-10 Two typical topologies.....................................................................................................................9-27

Issue 06 (2010-05-10)


v


About This Document

About This Document

Purpose This document provides an overview of the BTS3900 GSM. It also describes the system architecture, software and hardware structure, functional subsystems, configuration types, signal flow, clock synchronization modes, and topologies of the BTS3900 GSM.

Product Version The following table lists the product version related to this document.

Product Name

Product Version

BTS3900 GSM (hereinafter referred to as BTS3900)

V300R009

Intended Audience This document is intended for: l

Network planners

l

Field engineers

l

System engineers

Organization 1 Changes in BTS3900 GSM Technical Description

This provides the changes in the BTS3900 GSM Technical Description. 2 System Architecture of the BTS3900

The BTS3900 consists of the BBU3900, RFUs, and indoor macro cabinet. The BBU3900 and RFUs are installed in the indoor macro cabinet. Issue 06 (2010-05-10)


1


About This Document

3 Logical Structure of the BTS3900

The BTS3900 mainly consists of the BBU and RFUs. The logical structure of the BTS3900 consists of the RF subsystem, control subsystem, power subsystem, and antenna subsystem. 4 BTS3900 Monitoring System

The BTS3900 monitoring system enables the power monitoring, fan monitoring, and environment monitoring. 5 Reference Clocks of the BTS3900/BTS3900A

The BTS3900/BTS3900A supports four types of reference clocks: IP clock, line clock, free-run clock, and external clock. 6 Signal Flow of the BTS3900/BTS3900A

The signal flow of the BTS3900/BTS3900A consists of the traffic signal flow and the signaling flow of the BTS. The BTS3900/BTS3900A signal flow is classified into the DL traffic signal flow, UL traffic signal flow, and signaling flow. The BTS3900/BTS3900A supports three types of transmission mode: TDM, HDLC, and IP. The following sections describe the signal flow of the BTS3900/BTS3900A in three transmission modes respectively. 7 Topologies of the BTS

The topologies of the BTS include the TDM networking, IP networking, and HDLC networking. In practice, these topologies can be combined. Optimum utilization of the topologies can improve the quality of service and lower the investment on the transmission equipment. 8 Surge Protection Specifications of the BTS3900

The BTS3900 provides surge protection for its ports. The surge protection specifications of the BTS3900 ports consist of the DC or AC supply, antenna, transmission, and dry contact alarms. 9 Configuration of the BTS3900/BTS3900A

This describes the configuration principles of the BTS3900/BTS3900A, RF cable connections, and CPRI cable connections.

Conventions Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol

Description Indicates a hazard with a high level of risk, which if not avoided,will result in death or serious injury. Indicates a hazard with a medium or low level of risk, which if not avoided, could result in minor or moderate injury. Indicates a potentially hazardous situation, which if not avoided,could result in equipment damage, data loss, performance degradation, or unexpected results.

2


Issue 06 (2010-05-10)


About This Document

Symbol

Description Indicates a tip that may help you solve a problem or save time. Provides additional information to emphasize or supplement important points of the main text.

General Conventions

The general conventions that may be found in this document are defined as follows.

Convention

Description

Times New Roman

Normal paragraphs are in Times New Roman.

Boldface

Names of files, directories, folders, and users are in boldface. For example, log in as user root.

Italic

Book titles are in italics.

Courier New

Examples of information displayed on the screen are in Courier New.

Command Conventions

The command conventions that may be found in this document are defined as follows.

Convention

Description

Boldface

The keywords of a command line are in boldface.

Italic

Command arguments are in italics.

[]

Items (keywords or arguments) in brackets [ ] are optional.

{ x | y | ... }

Optional items are grouped in braces and separated by vertical bars. One item is selected.

[ x | y | ... ]

Optional items are grouped in brackets and separated by vertical bars. One item is selected or no i tem is selected.

{ x | y | ... } *

Optional items are grouped in braces and separated by vertical bars. A minimum of one item or a maximum of all items can be selected.

[ x | y | ... ] *

Optional items are grouped in brackets and separated by vertical bars. Several items or no item can be selected.

GUI Conventions

The GUI conventions that may be found in this document are defined as follows. Issue 06 (2010-05-10)


3


About This Document

Convention

Description

Boldface

Buttons, menus, parameters, tabs, window, and dialog titles are in boldface. For example, click OK .

>

Multi-level menus are in boldface and separated by the ">" signs. For example, choose File > Create > Folder.

Keyboard Operations

The keyboard operations that may be found in this document are defined as follows.

Format

Description

Key

Press the key. For example, press Enter and press Tab.

Key 1+Key 2

Press the keys concurrently. For example, pressing Ctrl+Alt +A means the three keys should be pressed concurrently.

Key 1, Key 2

Press the keys in turn. For example, pressing Alt, A means the two keys should be pressed in turn.

Mouse Operations

The mouse operations that may be found in this document are defined as follows.

4

Action

Description

Click

Select and release the primary mouse button without moving the pointer.

Double-click

Press the primary mouse button twice continuously and quickly without moving the pointer.

Drag

Press and hold the primary mouse button and move the pointer to a certain position.


Issue 06 (2010-05-10)


1 Changes in BTS3900 GSM Technical Description

1

Changes in BTS3900 GSM Technical Description

This provides the changes in the BTS3900 GSM Technical Description.

06 (2010-05-10) This is the fifth commercial release. Compared with issue 05 (2010-03-15), no part is added, modified or removed.

05 (2010-03-15) This is the fourth commercial release. Compared with issue 04 (2010-01-30), no part is added, modified or removed.

04 (2010-01-30) This is the third commercial release. Compared with issue 03 (2009-12-30), no part is added, modified or removed.

03 (2009-12-30) This is the second commercial release.

02 (2009-09-30) This is the first commercial release.

01 (2009-07-15) This is the draft release.

Issue 06 (2010-05-10)


1-1


2 System Architecture of the BTS3900

2

System Architecture of the BTS3900

The BTS3900 consists of the BBU3900, RFUs, and indoor macro cabinet. The BBU3900 and RFUs are installed in the indoor macro cabinet. Figure 2-1 shows the BTS3900 system. Figure 2-1 BTS3900 system

NOTE

The RFUs are of two types: DRFUs and GRFUs.

The BTS3900 mainly consists of the following components:

Issue 06 (2010-05-10)


2-1

2 System Architecture of the BTS3900 l

2-2


The BBU3900 is used for baseband processing and enables interaction between the BTS and the BSC.

l

The RFU is an RF filtering unit, which performs modulation, demodulation, data processing, and combining and dividing for baseband and RF signals.

l

The indoor macro cabinet houses the BBU3900 and RFUs. In addition, the indoor macro cabinet provides the functions such as power distribution, heat dissipation, and surge protection.


Issue 06 (2010-05-10)


3 Logical Structure of the BTS3900

3

Logical Structure of the BTS3900

The BTS3900 mainly consists of the BBU and RFUs. The logical structure of the BTS3900 consists of the RF subsystem, control subsystem, power subsystem, and antenna subsystem. Figure 3-1 shows the logical structure of the BTS3900. Figure 3-1 Logical structure of the BTS3900

NOTE l

In Figure 3-1, the power subrack (DC/DC) is configured in only the +24 V DC cabinet; the power subrack (AC/DC) is configured in only the 220 V AC cabinet.

l

If the TMA is configured, the GATM and the Bias-Tee must be configured.

The logical subsystems of the BTS3900 are as follows: Issue 06 (2010-05-10)


3-1


3 Logical Structure of the BTS3900 l

RF subsystem, implemented by the RFUs

l

Control subsystem whose functions are implemented by the BBU

l

Power subsystem whose functions are implemented by the following modules: – DCDU–01 in the BTS3900 cabinet (-48 V DC) – DCDU–01 and Power subrack (DC/DC) in the BTS3900 cabinet (+24 V DC) – DCDU–01 and Power subrack (AC/DC) in the BTS3900 cabinet (220 V AC)

l

Antenna subsystem whose functions are implemented by the following modules: – Antenna – Bais-Tee – GATM – TMA

3-2


Issue 06 (2010-05-10)


4 BTS3900 Monitoring System

4

BTS3900 Monitoring System

The BTS3900 monitoring system enables the power monitoring, fan monitoring, and environment monitoring.

BBU Monitoring Ports Figure 4-1 shows the monitoring ports of the BBU. Figure 4-1 Monitoring ports of the BBU

l

The BBU provides a maximum of two RS485 buses and 16 Boolean signals.

l

The modules on RS485 bus 0 cannot be interchanged with the modules on RS485 bus 1.

l

When two PMUs are configured, they cannot be connected to the same bus if the settings of the DIP switches on the two PMUs are the same.

Components of the Monitoring System Figure 4-2 shows the components of the BTS3900 monitoring system.

Issue 06 (2010-05-10)


4-1



Figure 4-2 Components of the monitoring system

NOTE

The RS485 bus 0 is indicated by bus0. The RS485 bus 1 is indicated by bus1.

Table 4-1 describes the monitoring modules of the BTS3900. Table 4-1 Monitoring modules of the BTS3900

Module

Address Bus

Pin

Description

PMU

bus0

-

Configured only in the BTS3900 cabinet (220 V AC)

FAN1

bus0

-

Mandatory

FAN2

bus0

-

Configured when two cabinets are stacked

GATM2

bus0

-

Optional

GATM1

bus1

-

Optional

EMU

bus1

-

Optional

Power subrack (DC/ DC)

Boolean

Pin 3 and pin 6

Configured only in the BTS3900 cabinet (+24 V DC)

Functions of the BTS3900 Monitoring System Table 4-2 describes the functions of the BTS3900 monitoring system. 4-2


Issue 06 (2010-05-10)



Table 4-2 Functions of the BTS3900 monitoring system

Module

Monitoring Function

FAN

l

Fan fault detection

l

Adjusting rotation speed of the fans

l

Detecting temperature and rotation speed of the fans

GATM

Reporting the RET control alarm signals

EMU

l

PMU

Power subrack (DC/DC)

Issue 06 (2010-05-10)

Communicating with the central processing unit through the two RS485 ports

l

Detecting the input voltage

l

Providing the independent sensor port for detecting humidity and temperature (12 V DC/24 V DC current type)

l

Providing the port for detecting the Boolean input signals in dry contact mode and in OC mode

l

Providing six external Boolean output control ports of the relay node type

l

Communicating with the central processing unit through the RS232/RS422 serial port

l

Managing the power system and the battery charging and discharging

l

Detecting power distribution and reporting alarms

l

Detecting module fault alarms (overvoltage output, no output, and fan fault)

l

Detecting module protection alarms (overtemperature protection, and overvoltage and undervoltage protection) and AC power failure alarms


4-3


5 Reference Clocks of the BTS3900/BTS3900A

5

Reference Clocks of the BTS3900/BTS3900A The BTS3900/BTS3900A supports four types of reference clocks: IP clock, line clock, free-run clock, and external clock.

IP Clock The IP clock acts as the clock source of t he BTS3900/BTS3900A, when the BTS uses the IP over FE transmission mode. The IP clock requires the configuration of the IP clock server in the network. The IP clock server carries the reference clock information in the UDP data packet, and then transmits the clock packets to the BTS. The BTS then resolves the clocks signals from the clock packet and uses these signals as reference clock source.

Line Clock The BBU3900 directly extracts the clock from the E1/T1 interface. Then, the BBU exports the precise 2 MHz and 8 kHz clocks after frequency dividing, phase locking, and phase adjusting. The 2 MHz and 8 kHz clocks are used for bit synchronization and frame synchronization in the BTS. The line clock consists of the trace BSC clock and trace transmission clock. The BTS extracts the clock signals from the BSC through the E1/T1 interface and uses them as the reference clock source. When the transmission mode of the BTS is upgraded from E1/T1 mode to IP mode, if there is no IP clock, the BTS extracts the clock signals from the transmission network through the E1/T1 interface and use them as the reference clock source.

Free-Run Clock In the absence of external clocks, the internal free-run clock ensures that the BTS keeps working properly for at least ninety days.

External Clock If the BBU3900 is configured with the USCU, the USCU can receive the external clock signals for the GTMU. The USCU supports clock signals including the GPS clock signal, RGPS clock signal, and BITS clock signal.

Issue 06 (2010-05-10)


5-1


6 Signal Flow of the BTS3900/BTS3900A

6

Signal Flow of the BTS3900/BTS3900A

The signal flow of the BTS3900/BTS3900A consists of the traffic signal flow and the signaling flow of the BTS. The BTS3900/BTS3900A signal flow is classified into the DL traffic signal flow, UL traffic signal flow, and signaling flow. The BTS3900/BTS3900A supports three types of transmission mode: TDM, HDLC, and IP. The following sections describe the signal flow of the BTS3900/BTS3900A in three transmission modes respectively.

TDM Transmission DL Traffic Signal Flow The DL traffic signal flow is transmitted from the BSC to the MS through the BTS3900/ BTS3900A. In the BTS3900/BTS3900A, the BBU and RFUs work together to process the DL traffic signals. Figure 6-1 shows the DL traffic signal flow. Figure 6-1 DL traffic signal flow Downlink traffic signal flow

1 E1

BBU

DBUS CBUS FHBUS 2

CPRI

RFU

3 RF signals

RFU

3 RF signals

RFU

3 RF signals

MS

…

BSC

The DL traffic signal flow is as follows: 1.

The E1 signals from the BSC are transmitted to the BBU through the E1 cable.

2.

After receiving the E1 signals, the BBU processes the E1 signals as follows: (1) Extracts clock signals from the E1 signals (2) Configures the BTS system based on the data configuration on the OML

Issue 06 (2010-05-10)


6-1



(3) Encapsulates the E1 data in the format of the CPRI frame, and then transmits the data to the RFU through the CPRI signal cable 3.

After receiving the signals, the RFU processes them as follows: (1) Decapsulates the high-speed CPRI frames to obtain the baseband signals (2) Transmits the baseband signals to the relevant operation units for encryption and interleaving (3) Converts the digital signals into the analog signals and modulates the analog signals into RF signals (4) Combines or divides the RF signals based on its own configuration (5) Transmits the combined or divided signals through the feeder and antenna

UL Traffic Signal Flow Compared to the DL traffic signal flow, the UL traffic signal flow is transmitted from the MS to the BSC through the BTS3900/BTS3900A. In the BTS3900/BTS3900A, the BBU and RFUs work together to process the UL traffic signals. Figure 6-2 shows the UL traffic signal flow. Figure 6-2 UL traffic signal flow Uplink traffic signal flow

RFU

1 E1

BBU

DBUS CBUS FHBUS 2

RFU

CPRI

3 RF signals

3 RF signals

MS

…

BSC

RFU

3 RF signals

The UL traffic signal flow is as follows: 1.

The antenna receives the signals sent from the MS. If the TMA is configured, the received signals are amplified by the TMA and then transmitted to the RFU through the feeder.

2.

After receiving the UL signals, the RFU processes the signals as follows: (1) Divides the UL signals from the antenna or diversity RX port (2) Converts the divided analog signals into the digital signals to obtain the baseband signals (3) Transmits the baseband signals to the relevant operation units for decryption and deinterleaving (4) Encapsulates the processed data in the format of the CPRI frame, and then transmits the data to the BBU through the CPRI signal cable

3.

After receiving the signals, the BBU processes the signals as follows: (1) Decapsulates the high-speed CPRI frames to obtain the baseband signals

6-2


Issue 06 (2010-05-10)



(2) Encapsulates the baseband signals in the format of the E1 frame, and then transmits the signals to the BSC through the E1 cable Signaling Flow The BTS3900/BTS3900A signaling flow refers to the signaling on the Abis interface. The BBU serves as the control unit and works with the RFUs to process the signaling. Figure 6-3 shows the signaling flow. Figure 6-3 Signaling flow Signaling flow

RFU

1

BBU

E1

DBUS CBUS FHBUS

RFU

2 CPRI …

BSC

RFU

The signaling flow is as follows: 1.

The signaling data received from the BSC is transmitted to the BBU through the Abis interface.

2.

The BBU encapsulates the signaling data in the format of the CPRI frame, and then transmits the signaling data to the RFU through the CPRI signal cable.

3.

The RFU decapsulates the CPRI signals into the baseband signals, and then transmits the baseband signals to the relevant operation units for processing.

4.

The RFU encapsulates the data of its own status in the format of the CPRI frame, and then transmits the data to the BBU through the CPRI signal cable.

5.

The BBU decapsulates the received CPRI signals to obtain the baseband signals.

6.

The BBU analyzes and processes the baseband signals to obtain the BTS status, and then sends the status data to the BSC on the Abis interface.

HDLC Transmission DL Traffic Signal Flow The DL traffic signal flow is transmitted from the BSC to the MS through the BTS3900/ BTS3900A. In the BTS3900/BTS3900A, the BBU and RFUs work together to process the DL traffic signals. Figure 6-4 shows the DL traffic signal flow.

Issue 06 (2010-05-10)


6-3



Figure 6-4 DL traffic signal flow Downlink traffic signal flow

HDLC Packet 1 E1

BBU

DBUS CBUS FHBUS 2

CPRI

RFU

3 RF signals

RFU

3 RF signals

RFU

3 RF signals

MS

…

BSC


The BSC encapsulates the service data in the format of the HDLC data packet, and then transmits the data to the BBU through the E1 cable.

2.

After receiving the E1 signals, the BBU processes the E1 signals as follows: (1) Extracts the clock signals from the E1 signal (2) Resolves the data packet in the HDLC format from the E1 timeslot signals bound to the HDLC channel, and then configures the BTS system based on the ESL and OML data resolved from the data packet (3) Encapsulates the HDLC service data in the format of the CPRI frame, and then transmits the data to the RFU through the CPRI signal cable

3.

After receiving the signals, the RFU processes the signals as follows: (1) Decapsulates the high-speed CPRI frames and HDLC packets to obtain the baseband signals (2) Transmits the baseband signals to the relevant operation units for encryption and interleaving (3) Converts the digital signals into the analog signals and modulates the analog signals into RF signals (4) Combines or divides the RF signals based on its own configuration (5) Transmits the combined or divided signals through the feeder and antenna

UL Traffic Signal Flow Compared to the DL traffic signal flow, the UL traffic signal flow is transmitted from the MS to the BSC through the BTS3900/BTS3900A. In the BTS3900/BTS3900A, the BBU and RFUs work together to process the UL traffic signals. Figure 6-5 shows the UL traffic signal flow.

6-4


Issue 06 (2010-05-10)



Figure 6-5 UL traffic signal flow Uplink traffic signal flow

RFU

HDLC Packet 1 E1

BBU

DBUS CBUS FHBUS 2

RFU

CPRI

3 RF signals

3 RF signals

MS

…

BSC

RFU

3 RF signals



2.

After receiving the UL signals, the RFU processes the signals as follows: (1) Divides the UL signals from the antenna or diversity RX port (2) Converts the divided analog signals into the digital signals to obtain the baseband signals (3) Transmits the baseband signals to the relevant operation units for decryption and deinterleaving (4) Encapsulates the processed signal in the format of the CPRI frame, and then transmits the signal to the BBU through the CPRI signal cable

3.

After receiving the signals, the BBU processes the signals as follows: (1) Decapsulates the high-speed CPRI frames to obtain the data in the format of the HDLC frame (2) Finds the HDLC transmission channel corresponding to this HDLC data packet, and then transmits the data in the format of the E1 frame to the BSC through the E1 cable

Signaling Flow The BTS3900/BTS3900A signaling flow refers to the signaling on the Abis interface. The BBU serves as the control unit and works with the RFUs to process the signaling. Figure 6-6 shows the signal flow of signaling processing.

Issue 06 (2010-05-10)


6-5



Figure 6-6 Signaling flow of signaling processing Signaling flow

RFU

HDLC Packet 1

BBU

E1

DBUS CBUS FHBUS

RFU

2 CPRI …

BSC

RFU


The BBU receives the signaling data from the BSC through the E1 cable.

2.

The BBU receives the relevant signaling data and processes the signaling data as required.

3.

The BBU encapsulates the signaling data to be processed by the RFU in the format of the CPRI frame, and then transmits the signaling data to the RFU through the CPRI signal cable.

4.

The RFU decapsulates the received CPRI signals and processes the signals as required.

5.


6.

The BBU decapsulates the received CPRI signals to obtain the data of the RFU status.

7.

The BBU analyzes and processes the baseband signals to obtain the BTS status, and then sends the status data to the BSC on the Abis interface.

IP Transmission DL Traffic Signal Flow The DL traffic signal flow is transmitted from the BSC to the MS through the BTS3900/ BTS3900A. In the BTS3900/BTS3900A, the BBU and RFUs work together to process the DL traffic signals. Figure 6-7 shows the DL traffic signal flow.

6-6


Issue 06 (2010-05-10)



Figure 6-7 DL traffic signal flow Downlink traffic signal flow HDLC Packet

UDP/IP Packet 1 FE

BBU

DBUS CBUS FHBUS 2

CPRI

RFU

3 RF signals

RFU

3 RF signals

RFU

3 RF signals

MS

…

BSC


The BSC encapsulates the service data in the UDP payload, and then transmits the IP packet to the BBU through FE transmission.

2.

After receiving the IP packet, the BBU processes the packet as follows: (1) If the current clock mode is configured to the IP clock, the clock packet is identified from the IP packet. The clock information is resolved from the clock packet for clock synchronization. (2) Identifies the packet on the ESL and OML and configures the BTS system based on the resolved data. (3) Identifies the service packet and deletes the UDP/IP header of the service packet. Encapsulates the service data in HDLC format and transmits the data to the RFU in the format of the CPRI frame.

3.

After receiving the signals, the RFU processes the signals as follows: (1) Decapsulates the high-speed CPRI frames and HDLC packets to obtain the baseband signals (2) Transmits the baseband signals to the relevant operation units for encryption and interleaving (3) Converts the digital signals into the analog signals and modulates the analog signals into RF signals (4) Combines or divides the RF signals based on its own configuration (5) Transmits the combined or divided signals through the feeder and antenna

UL Traffic Signal Flow Compared to the DL traffic signal flow, the UL traffic signal flow is transmitted from the MS to the BSC through the BTS3900/BTS3900A. In the BTS3900/BTS3900A, the BBU and RFUs work together to process the UL traffic signals. Figure 6-8 shows the UL traffic signal flow.

Issue 06 (2010-05-10)


6-7



Figure 6-8 UL traffic signal flow Uplink traffic signal flow HDLC Packet

UDP/IP Packet 1 FE

BBU

RFU

DBUS CBUS FHBUS 2

RFU

CPRI

3 RF signals

3 RF signals

MS

…

BSC

RFU

3 RF signals



2.

After receiving the UL signals, the RFU processes the signals as follows: (1) Divides the UL signals from the antenna or diversity RX port (2) Converts the divided analog signals into the digital signals to obtain the baseband signals (3) Transmits the baseband signals to the relevant operation units for decryption and deinterleaving (4) Encapsulates the processed signal in the format of the HDLC frame and then in the format of the CPRI frame, and then transmits the signal to the BBU through the CPRI signal cable

3.

After receiving the signals, the BBU processes the signals as follows: (1) Decapsulates the high-speed CPRI frames to obtain the data in the format of the HDLC frame (2) Obtains the UDP/IP header information corresponding to the HDLC data packet in the configuration data, and then encapsulates the HDLC frame payload in the UDP/ IP format. Then, the BBU checks the ARP table, finds the destination MAC address, encapsulates the packets in the MAC format, and transmits the packets to the BSC through FE transmission.

Signaling Flow The BTS3900/BTS3900A signaling flow refers to the signaling on the Abis interface. The BBU serves as the control unit and works with the RFUs to process the signaling. Figure 6-9 shows the signal flow of signaling processing.

6-8


Issue 06 (2010-05-10)



Figure 6-9 Signaling flow of signaling processing Signaling flow HDLC Packet

UDP/IP Packet 1

BBU

FE

RFU

DBUS CBUS FHBUS

RFU

2 CPRI …

BSC

RFU


The BBU receives the signaling data encapsulated in the UDP/IP format from the BSC through FE transmission.

2.

After decapsulating the signaling data, the BBU receives the relevant signaling data and processes the data as required.

3.

The BBU encapsulates the signaling data to be processed by the RFU in the format of the CPRI frame, and then transmits the signaling data to the RFU through the CPRI signal cable.

4.

The RFU decapsulates the received CPRI signals and processes the signals as required.

5.


6.

The BBU decapsulates the received CPRI signals to obtain the data of the RFU status.

7.

The BBU analyzes and processes the baseband signals to obtain the BTS status, and then sends the status data encapsulated in the UDP/IP format to the BSC through FE transmission.

Issue 06 (2010-05-10)


6-9


7 Topologies of the BTS

7

Topologies of the BTS

The topologies of the BTS include the TDM networking, IP networking, and HDLC networking. In practice, these topologies can be combined. Optimum utilization of the topologies can improve the quality of service and lower the investment on the transmission equipment.

TDM Networking The E1/T1 transmission is used between the BSC and the BTS, and the TDM transmission is used on the Abis interface. The TDM networking can be classified into the star topology, chain topology, tree topology, and ring topology. Figure 7-1 shows the star topology. Figure 7-1 Star topology

Figure 7-2 shows the chain topology. Figure 7-2 Chain topology

BSC

Issue 06 (2010-05-10)

BTS

BTS


BTS

7-1



Figure 7-3 shows the tree topology. Figure 7-3 Tree topology

BTS

BTS

BTS

BSC

BTS

Figure 7-4 shows the ring topology. Figure 7-4 Ring topology

Table 7-1 compares the topologies.

7-2


Issue 06 (2010-05-10)



Table 7-1 Comparison of topologies

Issue 06 (2010-05-10)

Topology

Application Scenario

Advantage

Star topology

Applies to common areas, especially densely populated areas, such as cities.

l

Simple networking

l

Easy engineering construction

l

Convenient maintenance

l

Flexible capacity expansion

l

High network reliability

Chain topology

Applies to sparsely populated areas in strip-like terrain, such as areas along highways and railway tracks.

Reduces costs in transmission equipment, construction, and transmission link lease.

Tree topology

Applies to areas where network structures, site distribution, and subscriber distribution are complicated, for example, an area where large-scale coverage overlaps hot spot or small-scale coverage.

Requires fewer transmission cables compared with the star topology.

Ring topology

Applies to common scenarios. If there is a breaking point in the ring, Due to its strong self-healing the ring breaks into two chains at the capability, the ring topology breaking point automatically. In this is preferred, if permitted by way, the BTSs preceding and following the routing. the breaking point can work normally despite the breaking point, thus improving the robustness of the system. For example, BTS0, BTS1, and BTS2 are sequentially connected to form a ring (clockwise). When a failure occurs at B, BTS0, the BTS topology preceding B, remains unchanged, and BTS2 and BTS1, the BTSs following B form a chain (anticlockwise), as shown in Figure 7-5.


7-3



Figure 7-5 Regrouping for disconnection in the ring topology

IP Networking The FE transmission is used between the BSC and the BTS, and the IP transmission is used on the Abis inter face. The IP networking consists of the layer-2 networking topology and layer-3 networking topology. Figure 7-6 shows the layer-2 networking topology. Figure 7-6 Layer-2 networking topology

Switch

BTS

Layer2 Network BSC

Switch

Switch

BTS

Figure 7-7 shows the layer-3 networking topology. Figure 7-7 Layer-3 networking topology

Router

BTS

IP Network BSC

Router

Router

7-4


BTS

Issue 06 (2010-05-10)



HDLC Networking The E1/T1 transmission is used between the BSC and the BTS, and the HDLC transmission is used on the Abis interface. The HDLC networking can be classified into the star topology, chain topology, and ring topology. Figure 7-8 shows the star topology. Figure 7-8 Star topology

Figure 7-9 shows the chain topology. The upper-level BTS transparently transmits the signals of the lower-level BTS. Figure 7-9 Chain topology

BTS

BSC

BTS

BTS

Figure 7-10 shows the ring topology. Figure 7-10 Ring topology

Issue 06 (2010-05-10)


7-5



7-6


Issue 06 (2010-05-10)


8 Surge Protection Specifications of the BTS3900

8

Surge Protection Specifications of the BTS3900

The BTS3900 provides surge protection for its ports. The surge protection specifications of the BTS3900 ports consist of the DC or AC supply, antenna, transmission, and dry contact alarms. NOTE

The unspecified surge current with maximum discharge current is called nominal discharge current.

Table 8-1 Surge protection specifications of the BTS3900

Port

Surge Protection Mode

Surge Current

DC power port

Differential mode

10 kA (8/20 us surge current)

Common mode


Differential mode


Common mode


Differential mode


Common mode


Dry contact port, RS485 port

Differential mode

250 A (8/20 us surge current)

Common mode

250 A (8/20 us surge current)

E1/T1 port

Differential mode


Common mode


Differential mode


Common mode


AC power port

Antenna port

RET antenna

Issue 06 (2010-05-10)


8-1


9 Configuration of the BTS3900/BTS3900A

9

Configuration of the BTS3900/BTS3900A

About This Chapter This describes the configuration principles of the BTS3900/BTS3900A, RF cable connections, and CPRI cable connections. 9.1 BTS3900/BTS3900A Configuration Principles The BTS3900/BTS3900A is configured with the antenna system, RFUs, and BBU. 9.2 RF Cable Connections of the DRFUs One end of the RF jumper is connected to the RF port on the DRFU, and the other end is connected to the feeder. You can determine the appropriate RF ports based on the actual networking modes. 9.3 RF Cable Connections of the GRFUs One end of the RF jumper is connected to the RF port on the GRFU, and the other end is connected to the feeder. You can determine the appropriate RF ports based on the actual networking modes. 9.4 RF Cable Connections for the Coexistence of the DRFUs and GRFUs One end of the RF jumper is connected to the RF port on the RFU, and the other end is connected to the feeder. You can determine the appropriate RF ports based on the actual networking modes. 9.5 CPRI Cable Connections of the RFUs The RFUs support two types of topology: star and chain.

Issue 06 (2010-05-10)


9-1



9.1 BTS3900/BTS3900A Configuration Principles The BTS3900/BTS3900A is configured with the antenna system, RFUs, and BBU.

Basic Configuration Principles l

If multiple hardware configurations meet the requirements for the RNP parameter settings, the configuration mode that supports smooth upgrades is preferred.

l

The DRFU is applicable to small- and middle-capacity scenarios; the GRFU is applicable to large-capacity scenarios. The DRFU and GRFU can be configured in the same cabinet or cell to support flexible capacity expansion.

l

Wide coverage is preferred. The DRFU supports the PBT, TX diversity, and 4-way RX diversity mode. Therefore, the DRFU can be applied to wide-coverage scenarios.

Antenna Configuration Principles l

One dual-polarized antenna can serve a maximum of two RFUs.

l

By default, RX diversity is adopted on the GSM network. That is, two feeders connected to two single-polarized antennas or one dual-polarized antenna must be configured in a cell.

l

Each sector of the BTS must be configured with the minimum number of antennas.

l

For the 2-way RX diversity, each sector has two antenna channels; for the 4-way RX diversity, each sector has four antenna channels.

RF Configuration Principles Table 9-1 describes the RF configuration principles of the BTS3900.

9-2


Issue 06 (2010-05-10)



Table 9-1 RF configuration principles of the BTS3900

Principle

Description

Configuration principles of the DRFU ports

l

In S3/3 configuration, three DRFUs need to be configured. The carriers provided by the middle DRFU belong to different l Rx1 in, Rx1 out, Rx2 in, cells. That is, the Rx1 in port and Rx2 out are the ports on the middle DRFU is the for signals between input port for RX diversity of interconnected DRFUs. carrier 1, which belongs to When two carriers the first cell. The input port provided by a DRFU for RX main of carrier 1 is belong to the same cell, both Rx1 in and Rx2 in can ANT1. The Rx2 in port is the input port for RX diversity of be the input ports for RX carrier 2, which belongs to diversity of the two the second cell. The input carriers. When two port for RX main of carrier 2 carriers provided by a DRFU belong to different is ANT2. cells, Rx1 in is the input port for RX diversity of carrier 1; Rx2 in is the input port for RX diversity of carrier 2. l

Issue 06 (2010-05-10)

Example

ANT1 and ANT2 are the TX ports of the duplexer. They are connected to jumpers.

CPRI_0 and CPRI_1 are the ports for high-speed electrical cables. The CPRI_1 port is connected to the CPRI port on the BBU or to the upper-level RFU in the case of cascaded RFUs. The CPRI_0 port is connected to the lower-level RFU in the case of cascaded RFUs.


9-3



Principle

Description

Configuration principles of the GRFU ports

l

The ANT_TX/RXA port supports signal reception and transmission, and the ANT_RXB port supports signal reception. They are connected to jumpers.

l

RX_INB and RX_OUTA are the ports for signals between interconnected GRFUs.

l

Configuration principles of a single cabinet

l

l

Configuration principles of multiple cabinets

9-4

Example -

CPRI_0 and CPRI_1 are the ports for high-speed electrical cables. The CPRI_0 port is connected to the CPRI port on the BBU or to the upper-level RFU in the case of cascaded RFUs. The CPRI_1 port is connected to the lower-level RFU in the case of cascaded RFUs. Star topology is adopted between the BBU and RFUs. The RFUs and the high-speed CPRI ports on the BBU have a one-toone relationship. That is, if slot 1 on the RFU is idle, CPRI port 1 on the BBU is also idle. When the DRFU is configured, the maximum cell configuration of a single cabinet is S4/4/4. When the GRFU is configured, the maximum cell configuration of a single cabinet is S12/12/12.

When star and chain topology is adopted between the BBU and RFUs, the RFU supports 3 levels of cascading in a chain and thus the BBU supports a maximum of 18 (6 x 3) RFUs.


-

Issue 06 (2010-05-10)



Principle

Description

Two TRXs of one DRFU configured in one sector

l

l

Number of DRFUs

l

l

Example

A single DRFU does not support the S1/1 application; however, three DRFUs support the S3/3 application.

For example, for a site in S5/4/7 cell configuration, nine DRFUs are installed to meet the requirements of S6/4/8 cell configuration, but When the DRFU works in data configuration is still TX PBT, TX diversity, or performed on the basis of the 4-way RX diversity mode, S5/4/7 cell configuration. a DRFU provides only one TRX. Therefore, you can configure the DRFU as required. When the number of TRXs of the site is less than 12, an odd number of TRXs can be configured for a cell. Number of DRFUs = round up [(number of TRXs + number of S1 cells) / 2]

l

S3/3/3: Number of DRFUs = round up (9 / 2) = 5; S1/2/3: Number of DRFUs = round up [(6 + 1) / 2] = 4.

l

After two TRXs are configured in one sector, the S5/5/5 configuration is S6/6/6. Number of DRFUs = (6 + 6 + 6) / 2 = 9.

When the number of TRXs of the site is greater than 12, an even number of TRXs should be configured for a cell. Number of DRFUs = round up (number of TRXs after two TRXs are configured in one sector / 2)

Number of GRFUs

One GRFU does not serve two cells. Each cell with a single antenna can be configured with a maximum of two GRFUs.

-

DRFU TRX allocation in double-antenna-system mode

After TRX allocation, the cells with an odd number of TRXs become neighboring cells of each other.

l

In S3/5/4 configuration, S5 can be divided into S3 + S2. Then, the cell configuration becomes S3/(3/2)/4.

l

In S2/5/5 configuration, the first S5 is divided into S2 + S3; the second S5 is divided into S3 + S2. Then, the cell configuration becomes S2/(2/3)/(3/2).

l

Issue 06 (2010-05-10)

S5 = S3 + S2 or S5 = S2 + S3

l

S6 = S4 + S2 or S6 = S3 + S3

l

S7 = S4 + S3 or S7 = S3 + S4

l

S8 = S4 + S4


9-5



9-6

Principle

Description

DRFUs at two bands configured in a site

l

If the number of DRFUs is not more than six in a double-band site, the DRFUs at two bands are configured in the same cabinet. If the RF cabinet is configured with less than three 900 MHz DRFUs and three 1800 MHz DRFUs, the 900 MHz DRFUs are installed in of the three slots on the left of the RF cabinet, and the 1800 MHz DRFUs are installed in the three slots on the right of the RF cabinet.

l

When two RF cabinets are configured and the number of DRFUs at each band is not more than six, the 900 MHz DRFUs are installed in the first RF cabinet and the 1800 MHz DRFUs are installed in the second RF cabinet. The DRFUs are installed in the slots according to the typical S4/4/4 configuration. When two RF cabinets are configured and the number of DRFUs at one band (for example, 900 MHz) is greater than six, other DRFUs at this band share the other RF cabinet with the DRFUs at the other band (for example, 1800 MHz). The mixed configuration of DRFUs at two bands is not allowed.


Example -

Issue 06 (2010-05-10)



Principle

Description

Example

Coexistence configuration Coexistence configuration principles of the DRFUs and principles of the DRFUs and GRFUs GRFUs are as follows: l

The primary BCCH is carried on a GRFU.

l

When the requirements of the output power and number of carriers are met and the cell configuration is greater than S4, a single DRFU is configured with one TRX; when two DRFUs are configured, one DRFU is preferably used.

l

The TX power of a DRFU and that of a GRFU within a cell are almost the same. The power difference should not exceed 0.5 dB.

l

When the DRFUs and GRFUs are configured in one cell, 4-way RX diversity and TX diversity are not supported.

l

The DRFUs and GRFUs are not recommended in the same new site.

-

NOTE

In the mode of configuring two TRXs in one sector, a DRFU belongs to only one sector.

BBU Configuration Principles l

A BBU has six CPRI ports and supports a maximum of 72 carriers.

l

Figure 9-1 shows the BBU slots. Figure 9-1 BBU slots

FAN

l

Issue 06 (2010-05-10)

0

4

1

5

2

6

3

7

UPEU/UEIU UPEU

Table 9-2 describes the board configuration principles of the BBU. Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

9-7



Table 9-2 Board configuration principles of the BBU

Module or Board

Description

UBFA

One UBFA must be configured.

UPEU

l

One UPEU must be configured.

l

A second UPEU can be configured when the backup power is required. The BBU, however, cannot be configured with the UPEU and the UEIU at the same time.

UEIU

The UEIU is optional and a maximum of one UEIU can be configured.

GTMU

l

One GTMU must be configured.

l

Can be installed only in the slot 6 (inhabited in Slot5 and Slot6).

UELP

l

USCU

Not required in the BTS3900

l

One UELP must be configured in the BTS3900A. The UELP is installed in slot 1.

l

The USCU is optional and a maximum of one USCU can be configured.

l

The USCU is installed in slot 0.

9.2 RF Cable Connections of the DRFUs One end of the RF jumper is connected to the RF port on the DRFU, and the other end is connected to the feeder. You can determine the appropriate RF ports based on the actual networking modes.

RF Cable Connections l

The TX/RX mode and Sending Receiving Mode described in the following list are set on the BSC side.

l

The RF cables differ from each other in colors. Figure 9-2 shows the mapping between the RF signal cables and their colors. Figure 9-2 Mapping between the RF cables and their colors RF jumper CPRI signal cable RF jumper between the cascaded RFUs

9-8


Issue 06 (2010-05-10)



S1 with Transmit Independency or Combining, S1 with Transmit Diversity, and S2 with Transmit Independency or Combining The S1 with Transmit Independency or Combining, S1 with transmit diversity, and S2 with Transmit Independency or Combining use the configuration of one DRFU and one dual polarized antenna. Table 9-3 describes the related configurations. Table 9-3 Configuration description (1)

Networking Configuration

Transmit mode

Sending Receiving Mode

Hardware Configuration

S1, Transmit Independency or Combining

Transmit Independency or Combining

Double Feeder (2TX + 2RX)

l

S1, Transmit Diversity

Transmit Diversity





l

One DRFU One dual polarized antenna

Figure 9-3 shows cable connections.

Issue 06 (2010-05-10)


9-9



Figure 9-3 RF cable connections of S1 (Transmit Independency or Combining/transmit diversity)/S2 (Transmit Independency or Combining)

ANT

RX1/IN

RX1/OUT

ANT1

RX2/IN

RX2/OUT

CPRI_0

CPRI_1

ANT2

RS T

R U N

ALM

AC T

VSWR

CPRI0

CPRI1

PWR

EX T-ALM1 EXT-ALM0

GTMU

TX0

RX0

CPRI0 TX1

RX1

TX2

RX2

TX

RX

CPRI1

ET H

CPRI2 TX3

RX3

TX 4

RX4

CPRI3

FE0

F 1 E

CPRI4 TX5

CPRI5

RX5

TST

E1 T1 /

MON0

LIU1 LIU3 RUN ALM ACT

USB

MON1

LIU0LIU2

UPEUE X T - LAM 1

EXT-A L M 0 MON1

MON 0

RS T PWR

RUN

The other available Sending Receiving Mode for the DRFU with Transmit Independency or Combining are Single Feeder (1TX + 1RX), Double Feeder (1TX + 1RX), and Double Feeder (1TX + 2RX). The transmit mode is Transmit Independency or Combining . Figure 9-4 shows cable connections.

9-10


Issue 06 (2010-05-10)



Figure 9-4 RF cable connections of the DRFU with Transmit Independency or Combining

ANT

ANT

TX/RX

ANT

TX

RX

RX1/IN

RX1/IN

RX1/OUT

ANT1

RX1/OUT

RX2/IN

RX2/IN

RX2/OUT

RX2/OUT

CPRI_0

CPRI_0

CPRI_1

CPRI_1

ANT2

RS T

R U N

RU N

ALM

AC T

VSWR

AC T

VSWR

CPRI0

CPRI1

CPRI0

CPRI1

PWR

PWR

EXT-ALM1 EXT-ALM0

RX0

ANT2

RS T

ALM

GTMU TX0

ANT1

CPRI0 TX1

RX1

TX2

RX2

CPRI1

RX3

T X4

RX4

FE0

CPRI4 T X5

RX5

CPRI5

CPRI3 TX

ET H

CPRI2 T X3

RUN ALM ACT U SB

TST

E1/ T 1

MON0

GTMU TX0

RX0

LIU1 LIU3

RX

F 1 E

MON1

LIU0 LIU2

CPRI0 TX1

RX1

TX2

RX2

TX

RX

CPRI1

UPEUE X T - AL M 1 E XT - AL M 0

MON1

ETH

RX3

T4 X

RX4

F E0

FE1

CPRI4 TX5 CPRI5

CPRI3

MON 0

RS T

CPRI2 TX3

RX5

TST

E1/ T 1

MON1

MON0

UPEUE X T - AL M 1 E X T - AL M 0

MON1

MON0

LIU1LIU3 RUN ALM ACT

USB

EX T-ALM1 EXT-ALM0

LIU0 LIU2

RS T

PWR

PWR

RUN

RUN

Single Feeder (1TX + 1RX)

ANT


ANT

TX/RX

RX RX1/IN

RX1/OUT

ANT1

RX2/IN

RX2/OUT

CPRI_0

CPRI_1

ANT2

RS T

R U N

ALM

AC T

VSWR

CPRI0

CPRI1

PWR

EXT-ALM1 EX T-ALM0

GTMU

TX0 RX0

CPRI0 TX1

RX1

TX2

RX2

CPRI1

CPRI3 TX

E T H

CPRI2 TX3

F 0 E

RX3

T X4

RX4

CPRI4 TX5 CPRI5

RX5

RUN ALM ACT U S B TST

E1/T1

MON0

LIU1LIU3

RX

F E 1

MON1

LIU0LIU2

UPEUE X T - LAM 1 E X T - AL M 0

MON1

MON 0

RS T PWR

RUN


Issue 06 (2010-05-10)


9-11



S2 with PBT, S3 with Transmit Independency or Combining, and S4 with Transmit Independency or Combining The S2 with PBT, S3 with Transmit Independency or Combining, and S4 with Transmit Independency or Combining use the configuration of two DRFUs and one dual-polarized antenna. Table 9-4 describes the related configurations. Table 9-4 Configuration description (2)


Transmit mode



S2, PBT

PBT


l







l

Two DRFUs One dual polarized antenna


9-12


Issue 06 (2010-05-10)



Figure 9-5 RF cable connections of S2 (PBT)/S3 (Transmit Independency or Combining)/S4 (Transmit Independency or Combining)

ANT

RX1/IN

RX1/OUT

RX1/IN

ANT1

RX1/OUT

RX2/IN

RX2/IN

RX2/OUT

RX2/OUT

CPRI_0

CPRI_0

CPRI_1

RS T

R U N

ANT1

CPRI_1

ANT2

ANT2

RS T

AL M

R U N

AL M

AC T

VSWR

AC T

VSWR

CPRI0

CPRI1

CPRI0

CPRI1

PWR

PWR

EX T-ALM1 EXT-ALM0

GTMU TX0

RX0

CPRI0 TX1

RX1

TX2

RX2

TX

RX

CPRI1

ET H

CPRI2 TX3

RX3 TX4

RX4

CPRI5

CPRI3

FE0

F 1 E

CPRI4 TX5

RX5

TS T

E1 T1 /

MON0

LIU1 LIU3

RUN ALM ACT USB

MON1

LIU0LIU2

UPEUE XT - AL M 1

EXT-A L M 0 MON1

MON 0

RS T PWR

RUN

The S3/3 with Transmit Independency or Combining uses three DRFUs and two dual-polarized antennas. Table 9-5 describes the related configurations. Table 9-5 Configuration description (3)


Transmit mode


S3/3, Transmit Independency or Combining


l

DRFU0: Single Feeder (1TX + 2RX)

l

DRFU1: Double Feeder (2TX + 4RX)

l


Hardware Configuration l l

Three DRFUs Two dual polarized antennas

Figure 9-6 shows cable connections. Issue 06 (2010-05-10)


9-13



Figure 9-6 RF cable connections of S3/3 configured with three DRFUs

ANT

ANT

RX1/IN

RX1/OUT

RX1/IN

ANT1 RX1/OUT

RX1/IN

ANT1

RX1/OUT

RX2/IN

RX2/IN

RX2/IN

RX2/OUT

RX2/OUT

RX2/OUT

CPRI_0

CPRI_0

CPRI_0

CPRI_1

CPRI_1

RS T

RU N

ALM

AC T

CPRI0

ANT2

RS T

RU N

ALM

VSWR

AC T

CPRI1

CPRI0

PWR

ANT1

CPRI_1

ANT2

ANT2

RS T

RU N

ALM

VSWR

AC T

VSWR

CPRI1

CPRI0

CPRI1

PWR

PWR

GTMU TX0

R X 0 CPRI0T X 1

RX1

TX2

R X 2 CPRI2 TX3

CPRI1

T X4

RX4

FE0

CPRI4 TX5 CPRI5

CPRI3 TX

ET H

RX3

RX5

RUN ALM ACT U SB

TST

E1 T1 /

MON1

UPEUE X T - LAM 1 E XT - AML 0

MON1

MON0

LIU1LIU3

RX

F 1 E

EXT-ALM1 EXT-ALM0

LIU0 LIU2

MON 0

RS T PWR

RUN

S2 with 4-Way RX Diversity The S2 with 4-way RX diversity uses two DRFUs and two dual-polarized antennas. The typical configurations are as follows: l

Set the receive mode to 4-Way Receive Diversity.

l

Set the sending receiving mode to Double Feeder (2TX + 4RX).


9-14


Issue 06 (2010-05-10)



Figure 9-7 RF cable connections of S2 with 4-way RX diversity

ANT

ANT

RX1/IN

RX1/OUT

RX1/IN

ANT1

RX1/OUT

RX2/IN

RX2/IN

RX2/OUT

RX2/OUT

CPRI_0

CPRI_0

CPRI_1

RS T

R U N

AM L

AC T

VSWR

CPRI0

CPRI1

ANT1

CPRI_1

ANT2

ANT2

RS T

R U N

ALM

AC T

VSWR

CPRI0

CPRI1

PWR

PWR

EX T-ALM1 EXT-ALM0

GTMU TX0

RX0

CPRI0 TX1

RX1

TX2

RX2

TX

RX

CPRI1

E T H

CPRI2 TX3

RX3

TX 4

RX4

CPRI5

CPRI3

F 0 E

F E 1

CPRI4 TX5

RX5

E1/T1

MON0


U S B TST

MON1

LIU0LIU2

UPEUE X T - LAM 1

EXT-A L M 0 MON1

MON 0

RS T PWR

RUN

S2 with Transmit Diversity and S4 with Transmit Independency The S2 with transmit diversity and S4 with transmit independency use the configuration of two DRFUs and two dual-polarized antennas. Table 9-6 describes the related configurations. Table 9-6 Configuration description (4)


Transmit mode



S2, Transmit Diversity

Transmit Diversity


l

S4, Transmit Independency



l

Two DRFUs Two dual polarized antennas


Issue 06 (2010-05-10)


9-15



Figure 9-8 RF cable connections of S2 (transmit diversity)/S4 (transmit independency)

ANT

ANT

RX1/IN

RX1/OUT

RX1/IN

ANT1

RX1/OUT

RX2/IN

RX2/IN

RX2/OUT

RX2/OUT

CPRI_0

CPRI_0

CPRI_1

RS T

R U N

ANT1

CPRI_1

ANT2

ANT2

RS T

ALM

R U N

AL M

AC T

VSWR

AC T

VSWR

CPRI0

CPRI1

CPRI0

CPRI1

PWR

PWR

GTMU

CPRI0 TX0 RX0 TX1

RX1

TX2

CPRI2 RX2 TX3

CPRI1

T X4

CPRI5

CPRI3 TX

ET H

RX3

CPRI4 RX4 TX5

FE0

RX5

RUN ALM ACT USB

TST

E1 T/1

MON1


MON1

MON0

LIU1LIU3

RX

F 1 E

EXT-ALM1 EX T-ALM0

LIU0 LIU2

MON 0

RS T PWR

RUN

S5 with Transmit Independency or Combining and S6 with Transmit Independency or Combining The S5 with Transmit Independency or Combining and S6 with Transmit Independency or Combining use the configuration of three DRFUs and two dual-polarized antennas. Table 9-7 describes the related configurations.

9-16


Issue 06 (2010-05-10)



Table 9-7 Configuration description (5)


Transmit mo mode




l




l


l


l


l


l


Hardware Configuration l l

Three DRFUs Two dual polarized antennas


Issue 06 (2010-05-10)


9-17



Figure 9-9 RF cable connections of S5 (Transmit Independency or Combining)/S6 (Transmit Independency or Combining)

ANT

RX1/IN

RX1/OUT

RX1/IN

ANT1

RX1/OUT

RX1/IN

ANT1

RX1/OUT

RX2/IN

RX2/IN

RX2/IN

RX2/OUT

RX2/OUT

RX2/OUT

CPRI_0

CPRI_0

CPRI_0

CPRI_1

CPRI_1

RS T

R U N

ANT

AM L

ANT2

RS T

R U N

AM L

AC T

VSWR

AC T

VSWR

CPRI0

CPRI1

CPRI0

CPRI1

PWR

ANT1

CPRI_1

ANT2

ANT2

RS T

RU N

ALM

AC T

VSWR

CPRI0

CPRI1

PWR

PWR

EXT-ALM1 EX T-ALM0

GTMU TX0

RX0

CPRI0 TX1

RX1

TX2

RX2

TX

RX

CPRI1

E T H

CPRI2 TX3

RX3

T X4

RX4

CPRI5

CPRI3

F 0 E

F E 1

CPRI4 TX5

RX5

E1/T1

MON0


U S B TS T

MON1

LIU0LIU2

UPEUE X T - LAM 1 E X T - AL M 0

MON1

MON 0

RS T PWR

RUN

S7 with Transmit Independency or Combining and S8 with Transmit Independency or Combining The S7 with Transmit Independency or Combining and S8 with Transmit Independency or Combining use the configuration of four DRFUs and two dual-polarized antennas. Table 9-8 describes the related configurations. Table 9-8 Configuration description (6)

9-18


Transmit mo mode






l





l

Four DRFUs Two dual polarized antennas

Issue 06 (2010-05-10)



Figure 9-10 shows cable connections. Figure 9-10 RF cable connections of S7 (Transmit Independency or Combining)/S8 (Transmit Independency or Combining)

ANT

RX1/IN

RX1/OUT

ANT

RX1/IN

ANT1

RX1/OUT

RX1/IN

ANT1

RX1/IN

ANT1

RX1/OUT

RX1/OUT

RX2/IN

RX2/IN

RX2/IN

RX2/IN

RX2/OUT

RX2/OUT

RX2/OUT

RX2/OUT

CPRI_0

CPRI_0

CPRI_0

CPRI_0

CPRI_1

CPRI_1

CPRI_1

RS T

RU N

ALM

AC T CPRI0

ANT2

RS T

ANT2

RU N

ALM

VSWR

AC T

VSWR

AC T

CPRI1

CPRI0

CPRI1

CPRI0

PWR

RUN

CPRI_1

ANT2

RS T

R U N

AM L

VSWR

AC T

VSWR

CPRI1

CPRI0

CPRI1

PWR

PWR

EXT-ALM1 EXT-ALM0

GTMU

TX0

CPRI0 RX0 TX1

RX1

TX2

CPRI2 RX2 TX3

CPRI1

RX3 TX4

CPRI4 RX4 TX5 CPRI5

CPRI3 TX

ETH

F E0

RX5

TS T

E1/ T 1

MON0

EXT-A L M 0 MON1

MON0


USB

MON1

LIU0LIU2

RX

FE1

ANT2

RS T

A M L

PWR

ANT1

UPEUE XT - AML 1

RS T PWR

RUN

9.3 RF Cable Connections of the GRFUs One end of the RF jumper is connected to the RF port on the GRFU, and the other end is connected to the feeder. You can determine the appropriate RF ports based on the actual networking modes.

RF Cable Connections The RF cables differ from each other in colors. Figure 9-11 shows the mapping between the RF signal cables and their colors. Figure 9-11 Mapping between the RF signal cables and their colors RF jumper CPRI signal cable RF jumper between the cascaded RFUs

Issue 06 (2010-05-10)


9-19



The Sending Receiving Mode of the GRFU is set on the BSC side. Table 9-9 describes the typical configurations of the Sending Receiving Mode for the GRFU. Table 9-9 Typical configurations of the sending receiving mode

GRFU Configuration


Single module


Two interconnected modules


The other available Sending Receiving Mode for the GRFU are Single Feeder (1TX + 1RX) and Double Feeder (1TX + 1RX). Figure 9-12 shows cable connections. Figure 9-12 RF cable connections (1)

ANT

ANT

TX/RX

ANT

TX RX_INB

RX_INB

RX_OUTA

RX_OUTA ANT_RXB

ANT_RXB

RUN

ALM

AC T

VSWR

CPRI0

MON

RX

CPRI1

RUN

ALM

AC T

VSWR

CPRI0

ANT_TX/RXA

CPRI1

ANT_TX/RXA

MON

CPRI1

CPRI1

CPRI0

CPRI0

PWR

PWR

EXT-ALM1 EX T-ALM0

GTMU

TX0 RX0

CPRI0 TX1

RX1

TX2

RX2

CPRI1

RX3

T X4

RX4

CPRI3 TX

ET H

CPRI2 TX3

FE0

CPRI4 TX5

CPRI5

RX5

RUN ALM ACT USB

TST

E1 T1 /

MON0

EXT-ALM1 EX T-ALM0

GTMU

TX0 RX0

LIU1LIU3

RX

F 1 E

MON1

LIU0 LIU2

CPRI0 TX1

RX1

TX2

RX2

TX

RX

CPRI1


MON1

ET H

RX3

TX 4

RX4

CPRI3

MON 0

RS T

CPRI2 TX3

FE0

F 1 E

CPRI4 TX5

CPRI5

RX5

TS T

E1/ T 1

UPEUE X T - A ML 1

E X T -L AM 0

MON1

MON0

RS T

PWR

PWR

RUN


MON0


USB

MON1

LIU0 LIU2

RUN


Cell Configuration with a Single GRFU When a dual-polarized antenna is configured, one TX channel and two RX channels are used. The ANT_RXB and ANT_TX/RXA ports receive the signals from the antenna to achieve RX diversity. 9-20


Issue 06 (2010-05-10)



Figure 9-13 shows cable connections. Figure 9-13 RF cable connections (2)

ANT

RX_INB RX_OUTA ANT_RXB

RUN

ALM

AC T

VSWR

CPRI0

CPRI1

ANT_TX/RXA

MON

CPRI1

CPRI0

PWR

EXT-ALM1 EXT-ALM0

GTMU TX0

RX0

CPRI0 TX1

RX1

TX2

RX2

TX

RX

CPRI1

E T H

CPRI2 TX3

RX3

T X4

RX4

CPRI5

CPRI3

F 0 E

F E 1

CPRI4 TX5

RX5

E1/T1

MON0

LIU1LIU3

RUN ALM ACT U S B TS T

MON1

LIU0LIU2

UPEUE XT - AL M 1

EXT-A L M 0 MON1

MON 0

RS T PWR

RUN

Cell Configuration with Two GRFUs The ANT_TX/RXA port on each GRFU supports the receiving and transmitting of signals. Two GRFUs provide RX signals for each other through the RF interconnection ports. Thus, the RX diversity is implemented. Figure 9-14 shows cable connections.

Issue 06 (2010-05-10)


9-21



Figure 9-14 RF cable connections (3)

ANT

RX_INB

RX_INB

RX_OUTA

RX_O UTA ANT_RXB

RUN

ALM

AC T

VSWR

CPRI0

ANT_RXB

CPRI1

RUN

ALM

AC T

VSWR

CPRI0

CPRI1

ANT_TX/RXA

ANT_TX/RXA

MON

MON

CPRI1

CPRI1

CPRI0

CPRI0

PWR

PWR

EXT-ALM1 EXT-ALM0

GTMU

TX0

RX0

CPRI0 TX1

RX1

TX2

RX2

TX

RX

CPRI1

E T H

CPRI2 TX3

RX3

T X4

RX4

CPRI5

CPRI3

F 0 E

F E 1

CPRI4 TX5

RX5

E1/T1

MON0


U S B TS T

MON1

LIU0LIU2

UPEUE XT - AL M 1

EXT-A L M 0 MON1

MON 0

RS T PWR

RUN

9.4 RF Cable Connections for the Coexistence of the DRFUs and GRFUs One end of the RF jumper is connected to the RF port on the RFU, and the other end is connected to the feeder. You can determine the appropriate RF ports based on the actual networking modes.

RF Cable Connections The RF cables differ from each other in colors. Figure 9-15 shows the mapping between the RF signal cables and their colors. Figure 9-15 Mapping between the RF cables and their colors RF jumper CPRI signal cable RF jumper between the cascaded RFUs

9-22


Issue 06 (2010-05-10)



Single Antenna System Configured With One DRFU and One GRFU When a DRFU and a GRFU share a dual-polarized antenna, the typical configuration of the Sending Receiving Mode for the DRFU and GRFU is as follows: l

The DRFU is configured with Single Feeder (1TX + 2RX).

l

The GRFU is configured with Single Feeder (1TX + 2RX).


ANT

EX T-ALM1 EXT-ALM0

GTMU

TX0

CPRI0 RX0 TX1

RX1

TX2

CPRI2 RX2 TX3

CPRI1

RX3

T4 X

CPRI3 TX

ETH

CPRI4 RX4 TX5

F E0

CPRI5

RX5

RUN ALM ACT USB

TS T

E1/ T 1

MON0

MON1

MON0

LIU1 LIU3

RX

FE1

MON1

LIU0LIU2

UPEUE X T - AL M 1

EXT-A LM0

RS T PWR

RUN

Double Antenna Systems Configured with One DRFU and One GRFU When a DRFU and a GRFU share two dual-polarized antennas, the typical configuration of the Sending Receiving Mode for the DRFU and GRFU is as follows: l

Issue 06 (2010-05-10)

The DRFU is configured with Double Feeder (2TX + 2RX). Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

9-23


9 Configuration of the BTS3900/BTS3900A l

The GRFU is configured with Double Feeder (1TX + 2RX).


ANT

ANT

RX1/IN

ANT1 RX1/OU T

RX2/IN

RX2/OU T

CPRI_0

CPRI_1

RS T

R U N

ALM

AC T

VSWR

CPRI0

CPRI1

ANT2

PWR

EXT-ALM1 EXT-ALM0

GTMU

TX0

RX0

CPRI0 TX1

RX1

TX2

RX2

TX

RX

CPRI1

E T H

CPRI2 TX3

CPRI3

F E 0

F E 1

RX3 TX4

RX4

CPRI4 TX5

CPRI5

RX5

E1/T1

MON0

EXT-A L M 0 MON1

MON0


U S B TS T

MON1

LIU0LIU2

UPEUE XT - AML 1

RS T PWR

RUN

Double Antenna Systems Configured with Two DRFUs and One GRFU When two DRFUs and a GRFU share two dual-polarized antennas, the typical configuration of the Sending Receiving Mode for the DRFUs and GRFU is as follows: l

The DRFUs are configured with Single Feeder (1TX + 2RX).

l

The GRFU is configured with Double Feeder (1TX + 2RX).


9-24


Issue 06 (2010-05-10)



Figure 9-18 RF cable connections (3)

ANT

ANT

EX T-ALM1 EXT-ALM0

GTMU

TX0

RX0

CPRI0 TX1

RX1

TX2

RX2

TX

RX

CPRI1

ET H

CPRI2 TX3

RX3

T X4

RX4

CPRI3

FE0

F 1 E

CPRI4 T X5 CPRI5

RX5

TS T

E1/ T 1

MON0

LIU1 LIU3

RUN ALM ACT USB

MON1

LIU0LIU2

UPEUE X T - LAM 1

EXT-A L M 0 MON1

MON 0

RS T PWR

RUN

9.5 CPRI Cable Connections of the RFUs The RFUs support two types of topology: star and chain. Figure 9-19 shows the typical topology of the DRFUs.

Issue 06 (2010-05-10)


9-25



Figure 9-19 Typical topology of the DRFUs

RX1/IN

RX1/OUT

RX1/IN

ANT1

RX1/IN

RX1/OUT

ANT1

RX1/IN

RX1/OUT

ANT1

RX1/OUT

RX1/IN

ANT1

RX1/IN

RX1/OUT

ANT1

RX1/OUT

RX2/IN

RX2/IN

RX2/IN

RX2/IN

RX2/IN

RX2/IN

RX2/OUT

RX2/OUT

RX2/OUT

RX2/OUT

RX2/OUT

RX2/OUT

Chain connection

Star connection

CPRI_0

CPRI_0

CPRI_0

CPRI_0

CPRI_0

CPRI_1

CPRI_1

CPRI_1

CPRI_1

CPRI_1

ANT2

RS T

R U N

AM L

AC T

CPRI0

ANT2

RS T

RU N

ALM

VSWR

AC T

CPRI1

CPRI0

ANT2

RS T

R U N

AM L

VSWR

AC T

CPRI1

CPRI0

PWR

AM L

VSWR

AC T

CPRI1

CPRI0

ALM

VSWR

AC T

CPRI1

CPRI0

CPRI0 TX1

RX1

TX2

RX2

CPRI1

RX3

T X4

CPRI4 TX5

RX4

CPRI3 TX

ET H

CPRI2 TX3

FE0

CPRI5

TST

VSWR

AC T

VSWR

CPRI1

CPRI0

CPRI1

PWR

PWR

EXT-ALM1 EX T-ALM0

GTMU

TX0 RX0

CPRI0 TX1

RX1

TX2

RX2

TX

RX

CPRI1


MON1

ET H

CPRI2 TX3

RX3

T X4

RX4

CPRI3

MON 0

RS T

E1 T1 /

ANT2

MON0

LIU1LIU3

RUN ALM ACT USB

AM L

LIU0 LIU2

RX

F 1 E

MON1

CPRI_1

RS T

R U N

PWR

RX5

CPRI_0

ANT2

RS T

RU N

PWR

EXT-ALM1 EXT-ALM0

TX0 RX0

ANT2

RS T

R U N

PWR

GTMU

ANT1

FE0

F 1 E

CPRI4 TX5

RX5

CPRI5

TST

E1/ T 1

MON0

LIU1 LIU3

RUN ALM ACT USB

MON1

LIU0 LIU2

UPEUE X T - AL M 1 E X T - LAM 0

MON1

MON0

RS T

PWR

PWR

RUN

RUN

Figure 9-20 shows the typical topology of the GRFUs. Figure 9-20 Typical topology of the GRFUs

RX_INB

RX_INB

RX_INB

RX_INB

RX_INB

RX_ OUTA

RX_ OUTA

RX_ OUTA

RX_ OUTA

RX_ OUTA

ANT_RXB

RUN

ALM

AC T

VSWR

CPRI0

MON

ANT_RXB

ANT_RXB

Chain connection

CPRI1

ANT_TX/RXA

RUN

ALM

AC T

VSWR

CPRI0

CPRI1

MON

RUN

ALM

AC T

VSWR

CPRI0

ANT_TX/RXA

ANT_RXB

CPRI1

MON

RUN

ALM

AC T

VSWR

CPRI0

ANT_TX/RXA

MON

CPRI1

ANT_TX/RXA

RX_INB RX_O U TA ANT_RXB

ANT_RXB

RUN

ALM

AC T

VSWR

RUN

ALM

AC T

VSWR

Star connection CPRI0

MON

CPRI1

CPRI0

ANT_TX/RXA

CPRI1

MON

ANT_TX/RXA

CPRI1

CPRI1

CPRI1

CPRI1

CPRI1

CPRI1

CPRI0

CPRI0

CPRI0

CPRI0

CPRI0

CPRI0

PWR

PWR

PWR

PWR

EX T-ALM1 EXT-ALM0

GTMU TX0

R X 0 CPRI0T X 1

RX1

TX2

R X 2 CPRI2 TX3

CPRI1

RX4

FE0

CPRI4 TX5 CPRI5

CPRI3 TX

ET H

RX3 TX4

RX5

TS T

E1 T1 /

GTMU TX0


USB

PWR

MON0

LIU0LIU2

RX

F 1 E

MON1

PWR

R X 0 CPRI0T X 1

RX1

TX2

R X 2 CPRI2 TX3

CPRI1

UPEUE XT - AL M 1

EXT-A L M 0 MON1

ET H

T X4

RX4

FE0

CPRI4 T X5 CPRI5

CPRI3 TX

MON 0

RS T

RX3

RX5

RUN ALM ACT U SB

TST

E1/ T 1

MON1

MON0


MON1

MON0

LIU1 LIU3

RX

F 1 E

EXT-ALM1 EXT-ALM0

LIU0 LIU2

RS T

PWR

RUN

PWR

RUN

NOTE

When the chain topology is used, a maximum of three levels of RFUs can be connected to one BBU.

9-26


Issue 06 (2010-05-10)

BTS3900 Technical Description

Recommend Documents