ASTM F2389 - 10 Standard Specification for Pressure rated Polypropy...
http://www.astm.org/Standards/F2389.ht
Back to Plastic Pipe Standards ASTM F2389 - 10
ASTM F2389 - 10 Standard Specification for Pressure-rated Polypropylene (PP) Piping Systems
Active Standard ASTM F2389 Developed F2389 Developed by Subcommittee: F17.61 F17.61 | |Book of Standards Volume: 08.04 Buy Standard (PDF)
more info
10 pages
$ 41.00
Buy Standard (Print)
more info
10 pages
$ 41.00
why redline?
20 pages
$ 49.20
Buy Standard + Redline (PDF)
ASTM F2389
Abstract
This specification establishes the requirements for polypropylene (PP) piping system components such as pipe, fittings, valves, and manifolds used in water service lines, hot-and-cold water distribution, hydronic heating, and irrigation systems to transport industrial process fluids, effluents, slurries, municipal sewage, etc. The piping system components covered here are made to metric sizes and IPS schedule 80 sizes, and pressure rated for water service and distribution supply. When tested according to the procedures provided herein, the piping components shall adhere to specified requirements for workmanship, dimensions, longitudinal reversion, melt flow rate, impact resistance, thermal stability and oxidative induction time (OIT), hydrostatic pressure, thermocycling, and oxidative stability in potable chlorinated water. This abstract is a brief summary summary of the referenced standard. It is informational informational only an d not an official part of the standard; the full text of the standard itself must must be referred to for its use and application. ASTM does not give a ny warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification establishes requirements for polypropylene (PP) piping system components made to metric sizes and IPS schedule 80 sizes, and pressure rated for water service and distribution supply (see Appendix X1). Included are criteria for materials, workmanship, dimensions and tolerances, product tests, and marking for polypropylene (PP) piping system components such as pipe, fitting fittings, s, valves, valves, and manifolds manifolds.. 1.2 The components governed by this specification shall be permitted for use in water service lines, hot-and-cold water distribution, hydronic heating, and irrigation systems. 1.3 The pipe and fittings produced under this specification shall be permitted to be used to transport industrial process fluids, effluents, slurries, municipal sewage, etc. The user shall consult the manufacturer to determine whether the material being transported is compatible with the polypropylene polyp ropylene pipi piping ng system and will will not affect the service life life beyond lim limits its acceptable to the user. user. 1.4 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical mathematical conversions conversions to SI SI units that that are provided for informati information on only only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine determine the applicabil applicability ity of regulatory regulatory requirements requirements prior prior to use.
1 f2
1/8/2013 4 16 PM
ASTM F2389 - 10 Standard Specification for Pressure rated Polypropy...
http://www.astm.org/Standards/F2389.ht
(purchase separately) 2. Referenced Documents Documents (purchase
ASTM Standards
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement D792 Test D1505 Test D1505 Test Method for Density of Plastics by the Density-Gradient Technique D1598 Test D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure D1600 T D1600 Terminolog erminologyy for Abbreviated Abbreviate d Terms Terms Relating Relat ing to Plastics D2122 Test D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings D2749 Symbols D2749 Symbols for Dimensions of Plastic Pipe Fittings D3895 Test D3895 Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry D4101 Specification D4101 Specification for Polypropylene Injection and Extrusion Materials F412 Termi F412 Terminology nology Relating to Plastic P lastic Piping P iping Systems Systems F2023 Test F2023 Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Tubing and Systems to Hot Chlorinated Water
Keywords
chlorine; fittings; industrial; municipal; pipe; polypropylene; potable water; process piping; thermoplastic; water; Piping systems; Polypropylene (PP) ;
ICS Code
ICS Number Code 23.040.20 (Plastic pipes)
DOI: 10.1520/F2389-10
ASTM International is a member of CrossRef. ASTM F2389 ( Plastic Pipe Standards)
Citing ASTM ASTM Standards Standar ds [Back to Top] Back to Plastic Pipe Standards Copyright © 1996-2012 ASTM. ASTM. All Rights Reserved. ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA, 19428-2959 USA
2 f2
1/8/2013 4 16 PM
