Demag Cranes
Single -girder cranes, Double-girder cranes Suspension cranes, Jib cranes Process cranes, Crane components After Sales Service
Cranes Quality and value for money
37427-2
37660-4
38998-4
High operating reliability and economic investments have to take priority in your planning.. The result: problem-free crane planning operation, minimum maintenance and maximum availability. Buy the right crane first time. Tell us about your handling requirements. With manual or automatic control or as part of a computer-con computer-controlled trolled material handling system. We can offer the crane that is right for you exactly in line with your needs.
We have been building cranes for decades, which results in our expertise. Experience gained all over the world by specialists who thoroughly test and integrate the latest technology into crane engineering until it is ready to enter series production. Computers, plotters, X-ray technology and many other simulation and testing methods are used every day. The results are evaluated and applied for every crane.
EDKE suspension crane with travelling hoist SWL up to 10 t Spans up to 24 m
ELKE overhead travelling crane with travelling hoist SWL up to 5 t Spans up to 15 m
2
Our wide range of cranes makes any solution possible: Steelwork built to mechanical engineering engineerin g tolerances. ■ Lifting gear with calculations based on serial hoists. ■ Complete travel drive assemblies. ■ Electrical equipment for all control requirements. You receive a comprehensive package containing all the information you require, plus after-sales service and supplies of wearing parts readily available. ■
EKWE overhead travelling crane with cantilever crab SWL up to 10 t Spans up to 35 m
EKKE overhead travelling crane with travelling hoist SWL up to 10 t Spans up to 24 m
Cranes Quality and value for money
37427-2
37660-4
38998-4
High operating reliability and economic investments have to take priority in your planning.. The result: problem-free crane planning operation, minimum maintenance and maximum availability. Buy the right crane first time. Tell us about your handling requirements. With manual or automatic control or as part of a computer-con computer-controlled trolled material handling system. We can offer the crane that is right for you exactly in line with your needs.
We have been building cranes for decades, which results in our expertise. Experience gained all over the world by specialists who thoroughly test and integrate the latest technology into crane engineering until it is ready to enter series production. Computers, plotters, X-ray technology and many other simulation and testing methods are used every day. The results are evaluated and applied for every crane.
EDKE suspension crane with travelling hoist SWL up to 10 t Spans up to 24 m
ELKE overhead travelling crane with travelling hoist SWL up to 5 t Spans up to 15 m
2
Our wide range of cranes makes any solution possible: Steelwork built to mechanical engineering engineerin g tolerances. ■ Lifting gear with calculations based on serial hoists. ■ Complete travel drive assemblies. ■ Electrical equipment for all control requirements. You receive a comprehensive package containing all the information you require, plus after-sales service and supplies of wearing parts readily available. ■
EKWE overhead travelling crane with cantilever crab SWL up to 10 t Spans up to 35 m
EKKE overhead travelling crane with travelling hoist SWL up to 10 t Spans up to 24 m
Cranes Quality and value for money
Steel structure Demag overhead travelling cranes are characterised by their very low dead weight combined with maximum rigidity. The ideal box-girder section to achieve this is calculated with the aid of modern computer programs. The advantages of this are low crane wheel loads and lightweight craneways which result in a reduction in building costs. All structural members are shot-blasted shot-blasted prior to fabrication and given a protective coat of zinc phosphate paint.
Hoist units Demag hoist units are designed to meet the requirements of the accepted European and other engineering and legislative standards. The design of the mechanical and electrical components is based on decades of practical experience. Demag sliding-rotor brake motors ensure loads are held safely even in the event of a power failure. Precise lifting and lowering of loads can be achieved by fitting a microspeed unit. Hoist units with load capacities of 1000 kg are fitted with load detectors as specified by the EC Machinery Directive with load monitoring to protect people, goods, the crane and supporting structure.
Additional equipment Travel drives with digital frequency inverters make it possible to achieve high positioning accuracy by means of infinitely variable long and cross-travel speeds. Smooth acceleration and deceleration reduce load sway, thus guaranteeing gentle handling of the load. Load spectrum recorder to determine the remaining theoretical hoist unit service life to FEM 9.755.
Information online On the www.cranes.demagcranes www.cranes.demagcranes.com .com Internet site, an array of additional additional End carriages Travel wheel, reduction gear and motor information on standard cranes has been have been combined to form a virtually made available for you via our planning maintenance-free assembly. consultant. Within a matter of seconds, Electrical equipment Quiet running only 70 dB(A) (A gearFunctional reliability by contactor control you can design your own crane installabox with Z motors) due to the enclosed of all movements. Easy operation via tion interactively which is tailored to gear stages running in oil, high-quality push-button pendants or joystick controls meet your individual needs. helical teeth and the natural damping in the case of cab control. Technical documentation is also provided properties of the travel wheels which are Orderly layout of the switchgear on on the TIP CD-ROM which is available manufactured from spheroidal graphite mounting plates housed in steel casings. upon request. cast iron GGG 70 which reduces wear on All connections of the flexible internal wheel treads and craneways due to the wiring are made with vibration-resistant vibration-resistant self-lubricating self-lubricating effect of the material. terminals. Easy fitting and removal of the reduction A main contactor ensures the simultaneous gear is a result of the sliding fit of its cut-out of all drive motors. hollow shaft on the travel wheel shaft. All Demag crane installations are supplied Both shafts are protected against with binding circuit documentation, e.g. corrosion. with the circuit diagrams divided into power feed and drive units. Crane geometry Excellent running properties including straight travel with little wear and minimum noise are the result of the perfect alignment geometry of all Demag overhead travelling cranes. To achieve this, the holes for the travel wheel bearings and the surfaces for mounting the crane girder to the end carriages are machined in one operation on special NC machine tools. ZKKE overhead travelling crane with double-rail crab, maintenance platform and operator cab SWL up to 80 t Spans up to 35 m ZKKE overhead travelling crane with double-rail crab SWL up to 80 t Spans up to 35 m
3
Single-girder overhead travelling cranes Economical solutions in the medium load range
36006-10
37661-9
The single-girder crane offers the advantage of a low dead weight. Low-headroom hoists provide good overall dimensions. Single-girder cranes are designed to be controlled from the floor. The power supply to the travelling hoist and the Demag DVS mobile control system are compact conductor line arrangements protected from accidental contact on box girder section cranes. Trailing cable arrangements are used on the profile section girder system.
S WL t
Hoist unit
Span m
Steelwork The steel structure is designed to DIN 15 018, Lifting Class 2, Loading Group 3 (other ratings available on request). The main girder and the end carriages are connected by high-tensile bolts. The hoist unit travels on the bottom flange of the main girder.
Type
FEM
Hook path
Operating speed
Cross tra vel speed
Long tra vel speed
4.6 / 14 m / min
10 / 40 m / min
4.6 / 14 m / min or 5 / 20 m / min
10 / 40 m / min
Long travel drives Maintenance-free drive units act directly on one travel wheel on each side of the crane, The travel drive, a Demag slidingrotor brake motor, guarantees smooth starting and allows a high number of starts and stops. The hard-wearing spheroidal graphite cast iron travel wheel has a taper-fit connection with the travel wheel shaft. This design is simple to service.
Main lifting Creep lifting
1 1.6 ELKE (profile section girder)
2 2.5 3.2
Chain 1Cm up to hoist or up to 15 rope 2m hoist
up to 8m
up to 4.5 m / min
1: 4 possible
4 5 1 2 EKKE (box section girder)
3.2 5 6.3 8 10
4
up to 24
Chain Chain hoist or hoist: rope 1 Bm hoist up to 2m
Rope hoist
Rope hoist: 1 Am up to 4m
up to 14 m / min up to 16 m / min
Chain hoist: 1: 4 up to 12.5 possible m / min up to 52 m Rope hoist: up to 1:4, 1:6, 6.3 m / min 1: 10 up to possible 8 m / min up to 6.3 m / min
Further information Standard cranes Brochure 208 557 44
Higher SWLs, larger spans and higher operating speeds on request.
Double-girder overhead travelling cranes For heavy loads and large spans
37970-6
37173-10
Double-girder cranes have the advantage of low overall height as the load hook can almost always be raised between the two crane girders. Double-girder cranes can be equipped for cab or floor control. Crab control is prescribed for speeds higher than 63 m/min. Used in combination with a radio remote control system for higher long travel speeds.
Cranes can also be controlled from a stationary control panel or by means or infrared or radio control. Automatic operation is also possible with appropriate equipment.
The cab or floor control unit can be in a fixed position on the girder, can travel with the crab or travel independently along the crane girder.
Further information Standard cranes Brochure 208 557 44 S WL
Span
t
m
Hoist unit Type
3.2 5 6.3 8 10 12.5 16 20 25 32 Higher SWLs, larger spans and higher operating speeds on request.
38381-3
40
up to 35
Hoist unit
FEM
Hook path Main lifting Creep lifti ng
up to 12.5 m / min up to 12.5 m / min up to 10 m / mi n up to 18 m / mi n up to 16 m / mi n 1 Am up to 52 m up to up to possibl e 12.5 m / min 4m up to 9 m / min up to 8 m / mi n up to 6 m / mi n up to 6.3 m / min up to 5 m / mi n
1:4, 1:6, 1:10 possi ble
Cross tra vel speed
Long tra vel speed
5 / 20 m / mi n
10 / 40 m / mi n
5
Suspension cranes Underrunning cranes for small and medium loads
36048-3
36379
36381-4
Underrunning cranes provide costeffective solutions and are particularly suitable for workshop and assembly applications. Favourable approach dimensions offer optimum utilization of the available space.
The drive and guide principle is simple, the carriages are fitted with direct drives and flanged travel wheels. Series-manufactured Demag components guarantee a high degree of availability.
Further information Demag standard cranes Brochure 208 557 44 S WL
Span
t
m
Hoist unit Art
1
Chain hoist or Rope hoist
2 3.2 5 6.3 8 10
6
up to 24
FEM
Hook path Main lifting
Long tra vel speed
4.6 / 14 m / min or 5 / 20 m / min
7 / 28 m / mi n or 10 / 40 m / min
Creep lifting
up to 14 m / min Chain hoist: 1 Bm up to 2m
up to 14 m / min up to 16 m / min up to 52 m up to 12.5 m / min possible
1)
Rope hoist
Cross tra vel speed
Rope hoist: 1 Am up to 4m
up to 6.3 m / min up to 8 m / min up to 6.3 m / min
Chain hoist: 1:4 possi ble
Rope hoist: 1:4, 1:6, 1:10 possible
1)
Larger spans can be bridged by means of multiple suspension. Higher load capacities and operating speeds on request.
Semi- and full-portal cranes of single and double-girder design
38290-1
36860 38290-1
They are the perfect solution for all areas in which handling performance is needed at frequently changing locations. The height and the width of the crane can be individually adapted to the relevant requirements. Features such as radio-remote control, frequency-regulated Indrive travel drives
manufactured in-house are available as options. Demag portal cranes of semi or fullportal design, single or double-girder models, safely handle your load. It is for example no problem to install Demag portal cranes in buildings of light design with walls that do not permit any
S WL
Chain Chain hoist: hoi st or 1 Bm rope up to 2m hoist
2 3.2 5
FEM
m
1
up to 24
6.3 rope hoist
8
This solution avoids waiting times, enhances workplace flexibility and increases the production performance per squared meter of building surface.
Hoist unit
Span
Type t
further loads. Portal cranes can also be installed as workplace or loading cranes under bridge cranes.
10
rope hoist: 1 Am up to 4m
Hook path
Operating speed
Cross tra vel speed
Long tra vel speed
4.6 / 14 m / min or 5 / 20 m / min
10 / 40 m / min
5 / 20 m / min
10 / 40 m / min
Main lifting Creep lifting
Chain hoist: 1:4 possible up to 52 m
up to 12.5 m / mi n
up to 52 m
up to 12.5 m / mi n
rope hoist: 1:4, 1:6, 1:10 possible
12.5 16 20 25 Higher SWLs, larger spans and higher operating speeds on request.
up to 30
rope hoist
1 Am up to 4m
1:4, 1:6, 1:10 possible
32
7
KBK crane construction kit Single and double-girder suspension cranes
36148
37994-4
Single-girder suspension cranes For three-dimensional, wide-ranging transportation. Low dead weight and suspension fittings for various structures allow cranes to be installed everywhere. Latching devices allow trolley transfer to monorails without having to deposit the load.
37601-27
Crane S WL kg
1)
80 125
Girder length
Span
100
m 3
m 2,85
I
6
4,65
485
II-L
8
7
670
I
10
7.6
465
I
3
2.75
485
7
6.1
10 4
Si ngle girder
Doubl e girder
250
500
II II
195
6
345
5
375
I
2.4
304
670
I I-L
5
440
7.6
515
II
4.3
645
3.7
700
5.2
680
7
5.9
745
5
760
11
8.5
505
3.8
965
4
3.5
760
3,1
1170
7
6.2
3.0
1370
2.7
1420
II-T
9
8.75
II
5
4.6
II-T
8
7.5
II
4
3.65
II-T
7
6.75
2500
I II
6
3200
I II
5
2000
Single-girder suspension crane
Dimen- KBK Suspensi on sion section distance loadi ng H m kg ²) mm 100 2.8 125 3.9
1600
8
II-L II-L
1000
Crane run way
KBK section
Crane type
Double-girder suspension cranes For the same SWL, double-girder cranes allow wider spans than single-girder cranes. Travel drives available if required.
520 530
I I I-L
II
II
II
1.1 0.7
Double-girder suspension crane
1700 1)
530
II
0.65
1700
5.4
700
I II
1.3
2600
4.2
700
I II
1.3
2600
2)
Intermediate load capacities, larger span dimensions and greater distances between suspensions on request. Customer must check load-bearing capacity of supporting structure.
Pillar and wall-mounted slewing jibs and cranes Workplace cranes for loads up to 10000 kg
37691-8
Slewing jibs and cranes are a cost-saving addition to integrated handling systems. There are also applications where only this type of equipment allows a particular handling problem to be solved. For example, in storage yards, on loading ramps or in buildings where other equipment cannot be installed because of the structural limitations. Slewing jibs and cranes are also frequently integrated in machinery.
37684-5
33676
Further information Pillar and wall-mounted slewing jibs and cranes Brochure 208 756 44 Technical Data 203 502 44
S WL kg
Outreach m
Sle wing range
Crane type
Hoi st unit Type
FEM
Main lifting Creep lifting Hook path speed speed
Hoist tra vel
Sl e wi ng
500 SSK, SDK or WSK
1000 1600
up to 12 m
3200 4000
up to 10,8 m
5000
up to 9 m
Chain hoist or rope hoist
SSK 270° SDK n x 360°
up to 7,5 m
8000
up to 6 m
10000
up to 5 m
as requested (up to 40 m as standard) Rope hoi st: 1 Am up to 2 m
SDK 6300
up to 8 m / mi n
Chain hoist: 1 Am, 1 Bm, 3m
WSK 180°
2000
Chain hoist: 1:4 possibl e
Chain hoist
Rope hoi st
up to 5,6 m / min up to 4,5 m / min up to 6,3 m / min up to 5 m / min up to 4 m / mi n
from 1600 kg up to 2000 kg electric manual or sle wing el ectri c tra vel mechanism recommended Rope hoi st: 1:4, 1:6, 1:10 possi ble
9
Special industry solutions with process cranes
Steel production Where safety has always been written with a capital S in the interest of people and processes, foundry cranes are available with 2 and 4 girders with crabs for transferring molten masses on both sides. For the safe handling of molten masses. 37393-2
37531-3
Steel handling Storage, handling operations, orderpicking and working processes have to be completed reliably in steel handling. Special magnets, stacker-cradle spreaders as well as tilt-type magnets provide for safe and reliable handling of coils, long bar material and sheet metal. Linking processes The very high quality workpieces weighing up to 200 t for manufacturing turbines and generators are positioned right down to the last millimetre and are deposited safely. In addition, the crane is also fitted with a separate cantilever crab for performing auxiliary operations.
37702-2
37596-1
10
Special industry solutions with process cranes
38515-1
Bulk material A crane in automatic mode fitted with four rope grabs for handling sand, ferrocarbon and shreds of plastic in a cement works. Recycling High-availability cranes equipped with grippers serve furnaces manually, automatically, fast and reliably all over the world. Working under aggressive conditions is no contest for these cranes. Operating personnel can monitor work processes safely from a control station or cab.
Paper industry For manufacturing paper: Pivoting load bars always transfer stacks of paper reels in the correct position from the paper machine to the stretching machine. Intermediate storage available. For storing paper: Vertical paper reel storage allows for optimum space utilisation. Vacuum units guarantee gentle handling of paper reels, are space-saving and safe.
37157-23
Aviation industry Teleplatform installations for maintaining, overhauling and for applying the paint finish to aeroplanes can approach any position of the plane precisely and without difficulty. Maintenance personnel can walk on the spacious platform with anti-collision protective mesh fencing to prevent any damage to the plane.
34270
33966
11
DK chain hoists Modular design with tomorrows technology
32337
Further information Demag DK chain hoists Brochure 20814744
Demag DK chain hoists are of functional design and modular construction. The design corresponds to the Calculation rules for series hoists of the association of European series hoist equipment manufacturers (FEM). ■ ■ ■
■
Ergonomically designed DSK control pendant. ■ Renowned sliding rotor brake motor with new rotor-shaft connection, DKUN 1 featuring a cylinder rotor motor with separately attached AC brake. ■ Choice of pole-changing motors: 1:4/1:6, or motors with one speed. ■
Small hook dimension C. Standard direct control. Three lifting speed variants. High lifting speeds, up to 25 m/min. Standard hook path 3 m, other hook paths also possible.
27787
Size for 2 / 1 S WL Si ze for 1 / 1 ree ving S WL
Size
Size
kg Hoi st speed m / min
FEM
kg
V1
V2
V3
V1 3m
4 / 1
7 / 1,7
250
DKUN 1-125
2m
4
4 / 1
7
7 / 1,7
1 Am
4 / 1
4 / 1
4 / 1
7
7 / 1,7
7
7 / 1,7
315
DKUN 1-160
3m
8 / 2
14 / 3.5
125
DKUN 1-125
2m
8
8 / 2
14
14 / 3.5
400
DKUN 1-200
DKUN 1-160
1 Am
8
8 / 2
400
DKUN 2-200
DKUN 2-160
3m
25
25 / 4
DKUN 1-200
1 Cm
DKUN 2-200
3m
8
8 / 2
DKUN 2-250
2m
8
DKUN 5-250
3m
DKUN 2-315
1 Am
DKUN 5-315
3m
DKUN 2-400
1 Cm
DKUN 5-400
2m
DKUN 5-500
1 Am
DKUN 10-500
3m
DKUN 5-630
1 Cm
8
DKUN 10-630
3m
DKUN 10-800 DKUN 16-800
250 315 400 500 630 800 1000
14 / 3.5
25
25 / 4
8 / 2
14
14 / 3.5
25
25 / 4
8
8 / 2
8
8 / 2
8
12,5 12.5 / 3.1 15
8 / 2
15
12.5 / 3.1
20 20 / 3.3
8 / 2
9
9 / 2.2 12.5 12.5 / 3.1
2m
9
9 / 2.2
3m
8
8 / 2
DKUN 10-1000 1 Am
9
9 / 2.2
DKUN 16-1000 2 m
8
8 / 2
DKUN 10-1250 1 Cm
9
9 / 2.2
8
8 / 2
DKUN 16-1600 1 Bm
12.5 / 3.1
DKUN 20-1250 3 m
12.5 / 3.1
15
1250 DKUN 16-1250 1 Am
1600
14
12.5 12.5 / 3.1 12.5 12.5 / 3.1
12.5 / 3.1
8 / 2
2000 DKUN 20-2000 1 Am
8
8 / 2
2500 DKUN 20-2500 1 Bm
8
8 / 2
12
1000
1250 1600
2000
1 Cm 4 3m
4
1 Cm 4 4
4 / 1
DKUN 5-250
3m
DKUN 2-315
1 Am
DKUN 5-315
3m
DKUN 2-400
1 Cm
DKUN 5-400
2m
4
4 / 1
4
4 / 1
DKST 5-1000
1 Cm 4
DKUN 5-500
1 Am 4
4 / 1
DKUN 10-500 DKUN 5-630
3m
1 Cm 4
2500
12,5 12,5 / 2
7,5 6,3 / 1,5
7,5 6,3 / 1,5
7,5 6,3 / 1,5
10 10 / 1,6
4 / 1
DKUN 10-630
3 m 4,5 4,5 / 11 6,3 6,3 / 1,5
DKUN 10-800
2 m 4,5 4,5 / 1,1
DKUN 16-800
3m
4
1 Cm 4,5
4,1
DKUN 10-1000 1 Am 4,5 4,5 / 1,1 2m
4
DKUN 16-1250 1 Am 4 DKUN 20-1250
3200
12,5 12,5 / 2
6,3 6,3 / 1,5
4,1
6,3 6,3 / 1,5
4,1
6,3 6,3 / 1,5
3 m 4,5 4,5 / 1,1
DKUN 16-1600 1 Bm
6,3 6,3 / 1,5
DKUN 10-1250 1 Cm 4,5 4,5 / 1,1
16 / 4
8
DKUN 20-1600 2 m
800
3m
2m
DKUN 16-1000
630
DKUN 2-250
DKST 10-2000
500
12.5 12.5 / 3.1
DKUN 2-160
DKST 2-500
V3
DKUN 1-100
DKUN 1-100
200
V2
200
100
160
Hoist speed m / mi n
FEM
6,3 / 1,5
4
4 / 1
4000
DKUN 20-2000 1 Am 4
4 / 1
5000
DKUN 20-2500 1 Bm 4
4 / 1
DKUN 20-1600
2m
DC-Pro chain hoists The new industrial standard
The quality of experience makes Demag technology what it is today. With the DC chain hoist and DR rope hoist, Demag Cranes & Components has achieved innovation in overhead materials handling, thus setting new standards.
hoist is ready to lift. The DC-Pro can be integrated into work processes flexibly and precisely and combines high productivity with smooth load handling. All inclusive: The all-in-one solution The new DC-Pro features essential functions for all types of applications, e.g. two hoist speeds, 24V contactor control and operating limit switches already in the standard version. At no extra cost. And a special advantage: The gearbox, brake and coupling work without the need for any maintenance for up to ten years.
Plug and lift The new Demag DC-Pro chain hoist is ready for use: All connections are simply plugged in. Thus plug and lift becomes reality: Simply hook the folding suspension bracket into the trolley or suspension eye, plug in the connectors and the
39204-2
39042-2
DC-Pro chain hoist
Load capacity
Type
kg
125
250
Hoist speed
Groups of mechani sms
V1 (m / min)
V2 (m / min)
DC-Pro 1
8 / 2
DC-Pro 2
16 / 4
DC-Pro 2
8 / 2
DC-Pro 5
12 / 3
Ree ving
Hook path
4m
5
4m 1 / 1
DC-Pro 5
6 / 1,5
DC-Pro 10
12 / 3
DC-Pro 10
6 / 1,5
DC-Pro 20
12 / 3
DC-Pro 20
6 / 1,5
DCM-Pro 1
8 / 2
DCM-Pro 2
16 / 4
DCM-Pro 1
8 / 2
DCM-Pro 2
16 / 4
DCM-Pro 2
8 / 2
DCM-Pro 5
12 / 3
or
Flexibly adaptable to any task The new DC-Pro chain hoist is available in two versions: as the DC-Pro chain hoist with a DSC control pendant and as the DCM-Pro Manulift for quickly handling loads with only one hand. A variety of proven load handling attachments facilitate optimum and flexible adaptation of the chain hoist to the task.
500 8
4m
1000 2000
2 / 1
Manulift DCM-Pro
80
4m
125
2,8 4m
1 / 1
or 4,3
250 4m
IP 55 enclosure, cyclic duration factor 60 % Intermediate load capacities are also available 13
DH hoist units in various designs for SWLs up to 100 000 kg
29086
24640
Hoist units have always been recognised as high integrity materials handling components. Used in all areas of industry in more than 100 countries. With their low dead weight and compact dimensions, they can handle loads up to 100000 kg safely and economically. Hoist units are available for various SWLs, lifting speeds and hook paths. 36345
The design complies with the Rules for the design of serial lifting equipment issued by the association of European series hoist equipment manufacturers (FEM) and is classified in Groups of Mechanisms to DIN 15020. Years of practical experience have gone into the mechanical and electrical design. Series production guarantees consistent quality.
Rope guide Of tough polyamide with lubricant aditive, high breaking strength. Pressure rollers mounted on anti-friction bearings. The two halves are easily assembled without special tools. Rope drum brake An extra brake for special safety requirements. Acts directly on the rope drum. Safety brake in the event of motor and gearbox failure; holding brake for handling molten loads. Integrated electrical equipment Newly developed, compact, mechanically interlocked contactors save space which can be used for additional electrical equipment. The new geared limit switch sets new standards for acurate switching points. Wire rope Demag hoist ropes offer a long service life and high safety, as long-term test have proved. Further information Brochure 20798744 Demag hoists units Technical Data 20334144 Monorail hoists 20334644 Double rail-crabs
14
Size for ree ving 2 / 1 S WL kg
Size
FEM
Hook path m v1
Hoist speed m / mi n v2 6.3 6.3 / 1
v3 10 10 / 1.7
6300
DH 632
1 Am
12; 20; 40; 52
4
10000
DH 1050
1 Am
16; 24; 40; 51
6.3 6.3 / 1
10 10 / 1.7
16 14 / 2.3
12500
DH 1063
1 Bm
16; 24; 40; 51
5
8 8 / 1.3
12.1 11.2 / 1.8
16000
DH 2080
2 Am
16; 24; 42
6.3 6.3 / 1
10 9 / 1.5
12.5
20000
DH 2100
1 Am
16; 24 42
5 5 / 0.8
8 7.1 / 1.2
10
25000
DH 2125
1 Bm
16; 24 42
4 4 / 0.6
6,3 5.6 / 0.9
8
The new Demag DR rope hoist More efficiency for cranes with capacities up to 10 t
Optimised for crane applications, the new Demag DR rope hoist meets all the requirements for state-of-the-art hoists for tomorrows needs. Besides the space-saving design and particularly long service life, it also offers a higher lifting speed for faster handling rates comprehensive standard features at an attractive price.
38972-2-1
38962
■
Low headroom trolley without counter weight ■ FEM Group 2 m +, 20% longer service life for the gearbox ■ Greater efficiency thanks to increased hoist speeds ■ Stepless cross-travel speed by inverter as standard ■ Hoist motor brake system with new safety concept ■ IP 55 enclosure, for operation under arduous conditions ■ New rope anchorage for fast and easy rope change ■ Bottom block with rope protection and handle recess for simple and reliable handling ■ Operation by means of DSE8-R push button control pendant system or optional DRC remote control with the latest radio technology. Both control systems with proportional push button and microswitch elements for step or stepless control. Display for load, load range and operating status ■
Size
Group of mechanisms
S WL
Hook path
t
m
FEM / ISO
DR 3
DR 5
DR 10
■
■
information read out from control system is standard in both push button stations Central control unit with PCB technology and integrated frequency inverter for cross travel Reliable signal transmission thanks to CAN Bus technology Many options are already included in the software and are easily activated EKDR 3
39205-1
EKDR 5
202
R
125
EKDR 10
197
R
145
R5
R5
=
=
=
=
m2
2/1
n2
2/1
m2 n2
m4
4/1
n4
4/1
b
420
515
m4 n4
480
515
b
0 0 1 ø 0 5 1
0 3 1
5 0 1
0 3 1
0 C 0 2
5 4
Li fting speed m / min V1
V2
V3
S WL
Hook path
t
m
2 / 1
5 6 1
0 5 1
0 1 1
5 , 7 3 1
0 C 7 2
3 5
Li fting speed m / min V1
V2
V3
S WL
Hook path
t
m
4 / 1
2 m / M 5
1,6
3 m / M 6
1,25
4 m / M 7
1
2
2 m / M 5
2,5
5
3 m / M 6
2
4 m / M 7
1,6
3,2
2 m / M 5
5
10
3 m / M 6
4
4 m / M 7
3,2
Li fting speed m / min V1
V2
V3
4 / 2
3,2 12; 20
12; 20
12; 20
12 / 2
12 / 2
10 / 1,7
18 / 3
18 / 3
2 - 18
2 - 25
2 - 25
2 - 25
2,5
4
8 6,3
6; 10
6 / 1
9 / 1,5
1 - 12,5 -
6; 10
6 / 1
9 / 1,5
-
-
-
-
5,8; 11,35
10 / 1,7
2 - 18
2 - 25
1 - 12,5
5 6; 10
5 / 0,8
1-9
1 - 12,5
4 3,2
15
DSE control pendants For contactor control
38285
38283-1
Manually actuated DSE control pendants are used for contactor controls for machinery, however, preferably for the control of hoists and conveying systems from the ground. The pendants feature a curved housing design for ergonomic handling with a naturally comfortable posture.
Identifi cati on plates
Size
Easy to install. Printed circuit board with central connection arrangement, no internal wiring in the control pendant enclosure ■ Switching elements feature plug-in connections which require no tools. An LCD display can be fitted to display the load ■
Part no.
S witching elements fitted
Weight
Qty
Size
kg
Emergency stop
DSE 8 P11
772 580 44
1 2
ESE N ESE 1
0.71
Emergency stop
DSE 8 P21
772 581 44
1 1 1
ESE N ESE 2 ESE 1
0.71
DSE 8 P22
772 582 44
1 2
ESE N ESE 2
0.71
DSE 8 P22 BE
772 583 44
1 1 1
ESE N ESE 2 ESE 2 BE
1 3
ESE N ESE 1
1 1 2 1 2 1 1 1 1 1
ESE ESE ESE ESE ESE ESE ESE ESE ESE ESE
Emergency stop
Emergency stop
DSE 8 P111
772 584 44
Emergency stop
DSE 8 P211
772 585 44
DSE 8 P212
772 586 44
DSE 8 P212 BE
772 587 44
Emergency stop
Emergency stop
16
N 2 1 N 2 1 N 2 1 2 BE
DSE 8 P222
772 588 44
1 3
ESE N ESE 2
DSE 8 P222 BE
772 589 44
1 1 2
ESE N ESE 2 ESE 2 BE
0.71 1)
0.75
Special switching elements can also be fitted in the 16 mm diameter openings. ■ ESEN switching element (emergency stop) with positive opening of the NC contacts ■ Positive opening of the interlocking contacts in the switching elements prevents simultaneous actuation of motions in opposite directions ■ Enclosure of high-quality thermoplastic which is highly resistant to impacts ■ Protective insulation to VDE 0100 part 410, section 6.2 ■ Actuating paths and forces to DIN 33401, retention force < 8 N ■ IP 65 enclosure to DIN VDE 0470 T.1 as standard ■ Enclosure non-flammable and resistant to fuels, salt water, grease, oils and lyes ■ Permissible ambient temperatures: rubber and thermoplastic parts 25 °C to + 70 °C ■ Strain relief by Polyamide-sheathed wire rope or cable with strain relief feature (2 TY cable) ■ Improved resistance to impacts thanks to an elastic cover ■
0.75
0.75
0.75 1)
0.75 0.75 1)
Further information Brochure 208 642 44 Technical data 203 119 44
1)
BE = double switching element, 2-stage ON, 1-stage OFF
RC-10 Radio Remote Control
37224-4
RC-10 remote for wireless control of cranes, shuttle cars and other machines. As a special feature, the RC-10 remote control unit has the facility for variable frequency operation: After switching on the remote control unit or by pressing the buttons on the transmitter, the receiver looks for the transmitter within the available frequency range: The operator can change the transmitter frequency at the press of a button; 67 transmission channels are available in total. Benefits: In built-up areas there is an increasing use of frequencies. A unit with variable frequency operation offers the best conditions for interference-free transmission and reception.
Hand-held transmitter: ■ Ergonomic hand-held transmitter with adjustable strap ■ Transmitter output approx. 10 mW; range approx. 100 m ■ 10 buttons of which 6 are 2-stage ■ Optimum safety ensured by electronic key ■ Hand-held transmitter can be fixed to walls with integrated inductive charging equipment (IP65) ■ Supply voltage of the hand-held transmitter via NiMH rechargeable battery block with plug-and-socket device, 100% cadmium and mercuryfree ■ Battery capacity sufficient for 4 hours of continuous operation or single-shift operation with 50 % CDF ■ Rechargeable battery condition indicator via LEDs, warning against discharged battery via LEDs and audio signals ■ Transmitter enclosure IP65 ■ Transmitter weight including battery approx. 500 g
Further information Brochure 208 359 44 Technical data 214 376 44
Hand-held transmitter
37224-5
33251
Receiver: ■ IP 65 plastic enclosure ■ Easy maintenance design, thanks to plug-in cards ■ Antenna integrated into enclosure ■ Relay outputs ■ Automatic frequency search ■ Ambient temperature from 20 to + 70 oC ■ Postal approval for many countries.
Receiver 309
LED electronic key
I/O
Transmitter on display
Lower
Lift
Left
Right
8 1 2 1 8 1
Backwards Forwards
1. St: Signal 2. St: Check limit switches
Stop
Special function 1
Special function 2
Parts list for RC-10: complete set (order no. 772 970 44) 1 1 2 1 1 1 1 1
RC-E 10 receiver 42-230 V 50/60 Hz RC-H 10 hand-held transmitter Rechargeable batteries (6 V) Charging unit (battery, 230 V 50/60 Hz) Operating instructions Coding label for hand-held transmitter (RC-H 10) Coding label (black and white) Coding label (7 segments, yellow)
17
Load detectors Load measurement and inceased safety for supporting structures
Efficient production requires all hoists to be working to capacity. The EC Machinery Directive stipulates overload protection for the design. Reliable operation over the whole load range, even under arduous conditions. Mechanical load detection MGS load link with mechanical microswitches and MKA-2 electronic evaluator for overload protection and overload cut-off. Maximum switching point deviation ± 2.5 %, after 2 x 10 6 load cycles.
34549
25494
%
Tensile force of rope
Hoists without creep lifting Load 110 %
110 100
% 125
Tensile force of rope
Load 110%
110 100
12,5 0
Time Lifting
Creep lifting
Time Main lifting
0 TM
18
0
Lifting
Main lifting
0
Time
Electronic load detection Carrier link with strain gauge bridge, FGB frequency generator and FAW-1 frequency evaluator for overload protection and overload cut-off. The electronics provide setpoint load limitation, summation measurement and hoist motor cut-off in the case of slack rope. An optional feature is a digital load display which can be used for assessing the approximate handling rate of an installation. Three-figure digital display, with a choice between Type ANZ-1 in the DST control pendant, Type ANK-1 in the drivers cab, or ANG-1 large format display (character height 120 mm).
Further information Load detectors on rope hoists Brochure 207 424 44 FGB-1(2)/FAW-1/FWL load detector Description and instructions 206 880 44 MGS/MKA-2 load detector Description and instructions 206 689 44
36717
Hoists with creep lifting
Load spectrum recorder Relevant legislation in many countries stipulates that the remaining safe working period (SWP) has to be determined. WLK-1 or FWL load spectrum recorders make it easy to calculate the remaining service life accurately.
Time
Operation with Dematik ® FGB/FAW-1 Overload cut-out In the case of hoist units without creep lifting, dynamic forces make it difficult to measure the load exactly. The rotating masses of the drive require a certain braking time before stopping. As a result, the load may be lifted off the ground, depending on the braking time, the weight of the load, the WK 2 and the elasticity of the supporting structure, or a higher load may occur. After cut-out, only lowering is possible. Overload protection After energising the main hoist, the weight of the load is measured continuously via the tensile force on the rope as the load is lifted. If the load is < 12.5% of the nominal load, the hoist runs up to the main lifting speed. If the load reaches 12.5%, the hoist is automatically switched to creep lifting speed and the measuring period TM starts automatically. If, during the measuring period, loads which are > 110% of the nominal load are reached, creep lifting is also switched off and only lowering is possible. With loads which are > 12.5% < 110%, the main lifting speed is switched on again at the end of the measuring period.
DGS/DGS-G geared limit switches For high cut-out accuracy
Easily fitted to hoists, roller doors, lifting platforms, rail-mounted carriages, telescoping mechanisms, etc., also to existing equipment. The geared limit switch is maintenancefree. Simple and infinitely variable setting of the switching points for all directions of movement using a screwdriver.
The maximum deviation from the switching points, once set, is no more than ± 2° on the output shaft over the complete life of the switch, even when using the whole range of adjustment. A counting mechanism is fitted as standard for recording the operating hours e.g. for maintenance purposes. There is provision for the installation of an electronic pulse generator for additional monitoring functions. Geared limit switches are available in two designs: either of closed (DGS-G) or of open design (DGS).
24624
DGS 3
24622
Further information DGS/DGS-G geared limit switch Brochure 208 031 44 DGS/DGS-G geared limit switch Description and information 206 462 44
Pulse generator (special design)
t f a h s e v i r D
Limit switch also available with 4 switching elements (DGS 4); length shown in brackets applies
t f a h s e r e t v n i r e D c
Mechanical data Transmission ratio i = 142 or 318 Useful revolutions = 140 or 315 (on output shaft) Run-on revolutions of output shaft = max. 1.3/2.9 Act ua tin g spe ed, rp m = ma x. 5 00 Infinitely variable adjustment of cam discs Ambient temperature °C 25 to +75 Service life of 5 x 10 6 revolutions of drive shaft Enclosure: DGS IP 00 DGS-G IP 65
Electrical data 3 (4) SEG switching elements, each with 2 NC contacts and positive opening Utilisation category AC 11 according to VDE 0660 Ith 2 = 16 A; U i = 600 V ~ C
DGS-G
Ue
220
3 80
500
Ie
6
6
4.5
19
Power supply lines KBK 0/25/100 trailing power supply lines
23759
37602-8
36381-6
KBK trailing power supply line system The KBK crane construction kit is also highly suitable for building your own power supply systems. Round or flat cross-section trailing cables can be used to supply power to electrical equipment on monorails and cranes.
Po wer supply type Profile section materi al
KBK 0
KBK 25
KBK 100
AL
ST
ST
Voltage max. (V)
dependent on round or flat cable type
Conductor cross-section (Cu / mm²)
dependent on round or flat cable type
Cont. current I N at 100% CDF (A)
Further information KBK 0, KBK 25, KBK 100 power supply lines Technical data 202 617 44
dependent on cabl e cross-section
Number of conductors Ambient temperature max. conti nuous (°C) Suspension di stance max. (mm) Bending radius min. (mm)
The profile sections can also be used for building small handling systems. The trolleys require no maintenance and run quietly inside the rail section where they are protected from corrosion. The cable trolleys have load capacities of up to 100 kg.
dependent on cabl e type
Profile sections
20 to + 70
KBK 0
KBK 25
28 28,5
up to 5000 1000
Mounting positi on
750
650 5 , 0 5
horizontal
Enclosure type for horizontal mounting
5 , 0 4
dependent on cabl e type KBK 100 50,5
Cable trolleys Voltage U max. (V)
dependent on cabl e type 5 6
Tra vel speed (m / min) Load capacity max. (kp)
20
100 15
25
100
Flat and compact electrical conductor lines for mobile equipment
DKK
37371-1
13001
Compact Line DCL ■ Compact conductor lines for 4 to 7 poles. ■ IP 23 or IP 24 high protection against accidental contact with sealing lip. ■ Screw connections for reliable longterm power supply. ■ Integrated expansion compensation, no special elements for thermal expansion compensation needed. ■ Outstandingly easy to install; all components are supplied pre-assembled. ■ Simple replacement of current collector trolleys or complete straight sections.
DKK compact conductor lines ■ Space-saving power supply lines for 4 or 5 poles. ■ High thermal and mechanical strength is provided by the aluminium enclosure. ■ High electrical safety with separate insulators. ■ Split enclosure provides easy access to the conductors. ■ Safety busbar line (IP 23 protection against accidental contact) DEL single conductors ■ High electrical safety due to large spacing between conductors. ■ Simple installation thanks to prepared assemblies. ■ Easy to maintain: conductors and current collector arms are easily visible. ■ Variety of suspension possibilities. Proximity switches can be fitted. ■ Curve sections possible from 500 mm radius.
DEL
25221
Further information DCL brochure 208 859 44 Technical data 202 617 44 DKK brochure 202 540 44 Technical data 206 000 44 DEL brochure 208 019 44 Technical data 202 673 44
Contuctor 2)
DEL
D KK
DCL
Current collector trolley 2)
DEL
DK K
DCL
Enclosure material
PVC
Alu
PVC
Voltage max. (V)
660
500
690
6
1 or 4
1 or 4
Load at 100% CDF (A)
40
40
40
Standard l engths, m Voltage Number of conductors
1000 V max.
24 500 V ~ max.
1 bi s
4 or 5
4 7 poles
25, 50
10, 16, 20, 30, 50, 70
10, 15, 25, 38, 56
- 30 to + 60
- 30 to + 100
- 30 to + 70
Minimum cur ve radius (mm)
500
900 (10, 16, 20 and 30 mm²)
800
Suspension centres, max. mm
3000
2000
2000
Type of enclosure ( wi th seal ing l ip)
IP 23
IP 23
I P 23 (24)
Conductor crosssecti on C u / mm² Ambient temperature °C
Max. connecting cable cross-section mm² (A)
24 690 V ~ max.
2)
6
2)
6
10
Fuses max. (A)
100
125
bis 100
Max. tra vel speed (m / min)
400
200 (straight tra vel)
200 (straight tra vel)
1)
Fine strand connecting cable in corrugated tube with PG 16 or 21 screw fitting. Connection cross-section for 1,5 mm² control conductor. 2) With profile suspension 1)
21
Demag DFW-L travel units
37851-2
Demag DFW-L travel units for overhead travelling cranes are high-quality components for materials handling and general engineering requirements. Of proven design, efficient and reliable, they are used as travel units for steel structures in crane and hoist applications and related designs in the mechanical engineering sector. DFW-L travel units are complete, driven rail-mounted travel units and can be connected direct to load-bearing structures.
Demag travel units make your installations efficient and reliable ■ Proven design for most arduous operating conditions ■ Various sizes, suitable for all necessary output requirements ■ Pole-changing motors for travel speeds up to 12.5/50.0 m/min ■ Indrive travel drives for frequency-regulated travel motions up to 80.0 m/min ■ Changes in track gauge can be accommodated using interchangeable spacer elements ■ Friction bearings lubricated for life, with large bearing distance to accommodate horizontal forces
■
■
Optimum mounting arrangement for horizontal guide rollers Maintenance-free
We offer the following mounting combinations to meet your design needs: ■ Travel unit with a side connection, e.g. side crane girder connection (standard) ■ Travel unit with a top connection, up to DFW-L 200 (option) We guarantee comprehensive consultation with our specialists already at the project stage. After the unit has been put into operation, our world-wide after-sales service ensures constant availability of your installation.
Further information DFW-L travel units Brochure 208 976 44 Trolley Type
Wheel Tra vel load max. wheel Ø kg mm
Wheel base ekt mm
Length)
Hei ght
Width)
mm
mm
mm
DF W-L-L 112
3350
112
1750
1920
180
214
DF W-L-E 112 for single girder DF W-L-E 125 connection DF W-L-E 160
3500
112
2000, 2500
2204, 2704
243, 247
135, 135
5000
125
2000, 2500, 3150
2224, 2724, 3374
281, 285, 289
138, 140, 140
7000
160
2000, 2500, 3150
2280, 2780, 3430
353, 357, 361
DF W-L-E 200
10000
200
2000, 2500, 3150, 4000
2336, 2836, 3486, 4336
436, 440, 444, 444
158, 160, 160 183, 185, 185, 185
DF W-L-Z 160
7000
160
2500, 3150
2780, 3430
352, 356
160
DF W-L-Z 200
10000
200
2500, 3150, 4000
2846, 3446, 4346
437, 438, 439
185
DF W-L-Z 250
16000
250
2500, 3150, 4000
2890, 3540, 4390
470, 473, 472
210
DF W-L-Z 315
22000
315
DF W-L-Z 400
30000
400
2500, 3150, 4000, 2975, 3625, 4475, 4200, 5000 4675, 5476 3150, 4000, 3735, 4585, 4500, 5000 5085, 5585
506, 508, 508, 508, 510 552, 550, 552, 552
for double girder connection
22
250 285
1) 2)
Length without buffer Width without drive
DRS wheel block system Innovative series-produced assemblies for travel units in materials handling and general engineering applications
36755
36753
The Demag DRS wheel block system offers innovative solutions to meet increasing demands for greater efficiency and improved travel drive features in the form of excellent quality and outstanding functional reliability. ■ The housing, enclosed on five sides, protects the travel wheels from external mechanical influence. ■ The housing is made of high quality, corrosion-resistant, pressure or gravity die-cast aluminium provided with a powder coating up to 90 µm thick. ■ From size 250, the enclosure is a spheroidal graphite iron casting with machined connecting surfaces. ■ Only complete drive units are able to provide the solution to complex drive requirements, all parts from the travel wheel, housing and connecting arrangement to the gearbox and motor are all from the same modular system.
RS wheel block type DRS
Wheel load max. kg
112
3500
112
125
5000
160
The patented asymmetrical housing eliminates the need for time-consuming removal and realignment of top-mounted wheel blocks when travel wheels have to be replaced. The housing remains connected to the installation. ■ Special flywheel drive with cylindricalrotor motor for smooth starting, optionally also with asynchronous conical sliding-rotor motors for controlled drive requirements. ■ Compact travel drive with splined journal shaft for direct transfer of the drive torque. ■ Patented integrated torque bracket with wide degree of freedom for varied connection possibilities for AM type offset gearboxes. ■
36754
37397-2
Tra vel wheel Wheel block dia. wei ght mm kg
Width
Height
Length
mm
mm
mm
7.3
96
131
190
125
9.9
98
147
220
7000
160
18.3
110
187
275
200
10000
200
35.7
130
235
340
250
16000
250
62
150
281
385
315
22000
315
117
180
350
470
400
30000
400
201
210
440
580
500
40000
500
352
240
565
700
Further information Brochure 208 724 44 Travel unit components: DRS wheel block system, KEM travel units Technical data 203 352 44 23
MPW crab for heavy loads and general mechanical engineering applications
38546-7
38546-1
38546-8
Our multi-purpose winches (MPW) are used in cranes designed for a wide array of different industries. Their flexibility and the combination possibilities of individual components in the various model series mean that they can cover a broadly based performance spectrum while largely avoiding interface problems.
Advantages of the MPW crab: ■ Crab frame of welded steel construction ■ Weight-optimised and torsionally rigid ■ Travel wheels extensively wear-free ■ Rugged, proven corner bearing construction ■ Crab frame accessible with toe guards and railings Fully equipped, assembled, and supplied just in time. With this ready-to-connect module, you can avoid both delivery time and interface problems. Further information Modules for the Demag Process Crane The modular design means that the crab Brochure 208 997 44 can be shipped in a container.
Optimised crane approach dimensions flexibility thanks to load capacity ranges in the corresponding rope reeving arrangements.
24
And all the motors and components are individually tested for functional integrity. So you get an MPW winch crab, assembled in accordance with largebatch manufacturing principles, with the following benefits: ■ Same travel unit technology as that employed for the crane travel units ■ Bolted transverse member ■ Minimum assembly work ■ Few interfaces (drum, gearbox, motor, brake all one unit) ■ Crab frame jig-welded ■ Modular construction
KEM travel units The optimum solution for rail-bound travel applications
38315-21
37238-1
38204-4
Demag travel units are used for railguided transport applications. They consist of the non-driven RN wheel set and a driven RAM wheel set featuring a gearbox and motor.
Demag travel units are not only used in the crane and materials handling sector, but also for related mechanical engineering requirements. All sizes are suitable for corner-mounting arrangements.
38173-3
Wheel sets
RAE, driven
RAE/RNE
RNE, non-driven
Further information Brochure 208 843 44 Travel unit components: DRS wheel block system, KEM travel units, DZW position meauring system Technical data 203 352 44
RAE/RNE corner bearing arrangement Tra vel wheel dia. mm
Wheel l oad max. kg
400
28.000
500
40.000
630
60.000
25
Service
Demag offers and provides the appropriate for the particular application. We give our customers the certainty that their materials handling facilities are safe and operate with maximum availability. Our service is only provided by qualified and experienced service engineers that we constantly keep up to date with the latest standards, recommendations and regulations. Our aim is to ensure that the right measures are taken at the right time for you. This enables you to concentrate on your business.
Worldwide presence outstanding Certainty materials handing service you can be sure As a successful and competent supplier Whatever needs to be done, we will of cranes and hoists as well as storage carry out the necessary measures for and conveying systems and a compre your cranes and hoists as well as storage hensive service we help you to meet your facilities and conveying systems at the production and delivery commitments. right time. You can be sure that ■ you meet the legal requirements To do this, we have developed the most closely-knit service network in the industry. and the maintenance and inspection intervals are not exceeded ■ your operating personnel work in Your benefit ■ 24-hour availability safety with the best possible accident ■ Short response times protection ■ Comprehensive service organisations ■ availability and smooth operation are ■ Qualified and competent service guaranteed ■ downtimes are reduced to a minimum personnel ■ the operating costs are always within your budget Your benefit ■ You can rely on the ability to meet legal requirements ■ Your facility operates safely and with minimum downtimes ■ Costs are minimised, since there are no follow-up costs ■ Systematic accident prevention and reduced absenteeism due to injury, resulting in simplified personnel planning ■ Reduced personnel costs
26
Service
37966-6
Availability your needs are met Your installations must be available when they are needed. If you want to fulfil your commitments and meet your needs, we are the right service partner for you. We tailor our services to meet the needs of your processes and factory working times. With preventive maintenance and by eliminating problems in good time, we help you to meet your targets: ■ ■
■
Short downtimes On-call standby with an appropriate response time Systematic problem analysis
Your benefit ■
■ ■ ■
Avoid downtimes and loss of production capacity Avoid recovery times and costs Avoid quality checks Avoid liability risks, e.g. financial penalties
Maintaining and increasing your assets enhanced facilities have added value
Your benefit ■
Whatever your company does, from time to time you will almost always have to
■
change production and manufacturing processes change locations allow for new operating conditions consider environmental factors and energy consumption requirements
■
■
■ ■ ■
With the right measures, the value of materials handling facilities an not only be maintained, but even increased. Adapting facilities to accommodate new technologies guarantees the further utilisation of the installations, improves operation and facilitates maintenance measures.
■
■ ■
■
■
Facilities adapted to accommodate new technologies Greater facility utilisation More effective operation Effective maintenance Higher productivity Easier and fast implementation of modernisation measures Longer service life at a higher level thanks to regular and correct measures Efficient cost planning and coordination of the measures in line with the available budget
Modernisation measures of this kind can usually be carried out easily and efficiently. By employing our teams of specialists, downtimes can be largely avoided. And as you would expect, we guarantee the measures and work carried out to ensure that the value of your assets is maintained for a long time. 37530-20
3 27
Quick quote
Fax no.: +971-4-8836861
To your Cranes Consultant
Please send an offer to:
Demag Cranes & Components (Middle East) FZE P.O. Box 16852 Jebel Ali, Dubai, United Arab Emirates
Company Business sector P.O. Box/Street Town or city/post code Contact Telephone
Telefax
Overhead travelling crane
mm mm m m
m m
m m
Bottom edge clearance limit: (girders, pipes, lamps, etc.)
m m m m
kg
Additional information
Required accessories (e.g. load handling attachments)
Crane runway already available? Yes
No, please offer
Crane runway length in m
Span in m Further wishes
Runway rail
Power supply already available? Yes, trailing cable Yes, busbar line
No, please offer
Please send an offer We have further questions, please call us.
m m
Quick quote
Fax no.: +971-4-8836861
To your Cranes Consultant
Please send an offer to:
Demag Cranes & Components (Middle East) FZE P.O. Box 16852 Jebel Ali, Dubai, United Arab Emirates
Company Business sector P.O. Box/Street Town or city/post code Contact Telephone
Telefax
Suspension crane m m
mm mm
Bottom edge clearance limit: (girders, pipes, lamps, etc.)
m m
m m
kg
Additional information
Required accessories (e.g. load handling attachments)
Crane runway already available? Yes
No, please offer
Crane runway length in m
Span in m Further wishes
Runway rail
Power supply already available? Yes, trailing cable Yes, busbar line
No, please offer
Please send an offer We have further questions, please call us.
