DDMC802 Data Sheet Rev L

DDMC802

Dimming/Relay/HF Ballast /Fan/Curtain Controller The DDMC802 is an 8 channel controller with a maximum load per channel of 2A. A variety of output modules are available to suit different types of loads and the DDMC802 can accept up to eight plug in modules, which by their removable design also facilitate ease of servicing. Available module types include: • Trailing edge phase control dimmer, suitable for use with most types of dimmable electronic transformers. • Leading edge phase control dimmer, suitable for incandescent lamps and some types of dimmable electronic transformers. • HF Ballast contoller, suitable for controlling 1-10V and digital ballasts and transformers (a relay module should be paired with the HF ballast module when controlling 1-10V ballasts). • Relay module, suitable for most types of switched loads. • Fan control module. • Curtain control module. The device is DIN rail mountable, designed to be installed in a switchboard, optionally next to circuit breakers feeding the circuits to be controlled.

technical data

DDMC802-MO

Supply 230V ±14% 50/60Hz Single Phase at 16A

1 x RS485 DyNet and DMX512 serial port 1 x AUX programmable dry contact input

Outputs 8 x output slots at 2A each. Maximum device load 16A. A derating factor may need to be applied if installed in a smaller sealed switchboard when using Leading or Trailing edge modules, see Instruction Manual for details. Some modules occupy 2 slots. Available modules include: DDBM100 - 1 Channel; 1-10V or digital HF Ballast control. Occupies 1 slot DDCM102 - 1 Channel x 2A SPDT Curtain Control. Occupies 2 slots DDFM102 - 1 Channel 400VA Fan Control. Occupies 2 slots DDLM102 - 1 Channel x 2A Leading edge dimmer. Regulating Device - Triac - 20A, 600V. Occupies 1 slot DDLM104 - 1 Channel x 4A Leading edge dimmer. Regulating Device - Triac - 20A, 600V. Occupies 2 slots DDRM104 - 1 Channel x 4A relay. Switching device - Relay, 16A TV5 100A surge. Occupies 1 slot DDTM102 - 1 Channel x 2A Trailing edge dimmer. Regulating Device - Dual MOSFET’s 20A, 600V, 62A surge. Occupies 1 slot

DyNet DC Supply 120mA

Dimmer Module Power Conditioning • Regulated outputs • Over voltage protection • Surge protection • Brownout/Sag protection • Spike protection • Soft start • 16 bit fade resolution (65,535 steps) Front Panel Controls Channel Override switches Channel Status indicators Service Switch Service LED RS485 DyNet port Control Inputs

load compatability

options

Digital and 1-10V HF Ballasts Digital and 1-10V transformers Incandescent lamps Magnetic transformers Manual Override -MO

Preset Scenes 170 User Controls Service Switch Diagnostic LED Diagnostic Functions Circuit run time tracking on each channel Device Online/Offline status Supply Terminals Line, Neutral, Earth 2 x 2.5mm2 or 1 x 4mm2 conductor size Output Terminals Line, Neutral for each channel, 2 x 2.5mm2 or 1 x 4mm2 conductor size Operating Environment 0º to 40ºC ambient temperature 0% to 95% RH non condensing Compliance CE, C-Tick Enclosure Polycarbonate DIN Rail enclosure (12 unit) Dimensions H 93mm x W 211mm x D 75mm Weight Packed weight 0.94kg

Leading edge electronic transformers Switched loads Trailing edge electronic transformers

DDMC802

Dimming/Relay/HF Ballast/ Fan/Curtain Controller electrical diagram

mounting dimensions

T 6.3A M205

Output Card 1 Slot T 6.3A M205


Supply: 230V 16A 1 Phase L N E






Output Card 8 Slot

CH1 N CH2 N CH3 N CH4 N CH5 N CH6 N CH7 N CH8 N

AUX

D-

DyNet RS485

+15V

D+

GND

Shield

µP

For further information contact:

t +61 2 8338 9899 • f +61 2 8338 9333 dynalite-online.com • [email protected]

DDMC802 Data Sheet Rev L October 2009

Specifications subject to change without notice. © Dynalite Intelligent Light Pty Ltd. Unit 6, 691 Gardeners Road Mascot 2020 Australia. ABN 97 095 929 829. All rights reserved. Dynalite, DyNet and associated logos are the registered trademarks of Dynalite Intelligent Light Pty Ltd. Not to be reproduced without permission.

DDMC802 Data Sheet Rev L

Recommend Documents