Article About Pipe P.E coatingDescription complète
PE piping design handbook
PE piping design handbook
Full description
Full description
a b
Data sheetDeskripsi lengkap
API 610Full description
Standard Specification for High-Density Polyethylene (PE) Line Pipe
This is a spread sheet developed by PIP for Blast Resistant Building data.Descripción completa
Formula to calculate optimum pipe diameter sometimes useful for calculate the size of optimum pipe based on flow debit of fluid.
Carte crestina in format electronic
Full description
Specification for Pipe Support
Full description
DataFull description
A Cheat Sheet for the TAU test in Data Structures.
Gas Turbine Data SheetDescription complète
DATA SHEET PIPE POLYETHYLENE
PT.PGN (Persero) Tbk No. Doc :
Revisi:
Page : 1 dari 5
Location
Onshore
Fluid Service
Natural Gas
Design Code
ISO Standard 4437
Quantity
(Note 1)
GENERAL
PROCESS CONDITION
Maximum Design Temperature
deg C
40
Minimum Design Temperature
deg C
15
Design Pressure
barG
System Pressure Rating Class Nominal Diameter
DESIGN & CONSTRUCTION
MATERIAL FUSION COMPABILITY INSPECTION AND TESTING MARKING
4
2
Other
#150 mm
125
SDR Number
11
Joint Length
12 m long straight length
Squeeze off ability
Yes
Fitting Requairement
Yellow
PE Number
80
Material Grade
MDPE
Fusion Compability Test for Butt Joint
(Note 3) and as per ISO 4437
Inspection and Testing
(Note 3)
Handling and Transportation
As per IGEM/G/8 Standard
Design Standard
(Note 3)
Manual Guarantee
1 Year
CERTIFICATE Production and Material Certificate
Note 1. Vendor/Supplier/Contractor Vendor/Supplier/Contractor to complete 2. Refer to Scope of W ork, Bid Document, or Attachment specified by PGN 3. Shall refer to Standard Teknis and Material - Pipa Polyethylene
Yes
No
6
DATA SHEET PIPE POLYETHYLENE
PT.PGN (Persero) Tbk No. Doc :
Revisi:
Page : 2 dari 5
Location
Onshore
Fluid Service
Natural Gas
Design Code
ISO Standard 4437
Quantity
(Note 1)
GENERAL
PROCESS CONDITION
Maximum Design Temperature
deg C
40
Minimum Design Temperature
deg C
15
Design Pressure
barG
System Pressure Rating Class Nominal Diameter
DESIGN & CONSTRUCTION
MATERIAL FUSION COMPABILITY INSPECTION AND TESTING MARKING
4
2
Other
#150 mm
90
SDR Number
11
Joint Length
12 m long straight length
Squeeze off ability
Yes
Fitting Requairement
Yellow
PE Number
80
Material Grade
MDPE
Fusion Compability Test for Butt Joint
(Note 3) and as per ISO 4437
Inspection and Testing
(Note 3)
Handling and Transportation
As per IGEM/G/8 Standard
Design Standard
(Note 3)
Manual Guarantee
1 Year
CERTIFICATE Production and Material Certificate
Note 1. Vendor/Supplier/Contractor to complete 2. Refer to Scope of W ork, Bid Document, or Attachment specified by PGN 3. Shall refer to Standard Teknis and Material - Pipa Polyethylene
Yes
No
6
DATA SHEET PIPE POLYETHYLENE
PT.PGN (Persero) Tbk No. Doc :
Revisi:
Page : 3 dari 5
Location
Onshore
Fluid Service
Natural Gas
Design Code
ISO Standard 4437
Quantity
(Note 1)
GENERAL
PROCESS CONDITION
Maximum Design Temperature
deg C
40
Minimum Design Temperature
deg C
15
Design Pressure
barG
System Pressure Rating Class Nominal Diameter
DESIGN & CONSTRUCTION
MATERIAL FUSION COMPABILITY INSPECTION AND TESTING MARKING
#150 mm
4
2
Other
63
SDR Number
11
Joint Length
50 up to 100 long coil
Squeeze off ability
Yes
Fitting Requairement
Yellow
PE Number
80
Material Grade
MDPE
Fusion Compability Test for Butt Joint
(Note 3) and as per ISO 4437
Inspection and Testing
(Note 3)
Handling and Transportation
As per IGEM/G/8 Standard
Design Standard
(Note 3)
Manual Guarantee
1 Year
CERTIFICATE Production and Material Certificate
Note 1. Vendor/Supplier/Contractor to complete 2. Refer to Scope of W ork, Bid Document, or Attachment specified by PGN 3. Shall refer to Standard Teknis and Material - Pipa Polyethylene
Yes
No
6
DATA SHEET PIPE POLYETHYLENE
PT.PGN (Persero) Tbk No. Doc :
Revisi:
Page : 4 dari 5
Location
Onshore
Fluid Service
Natural Gas
Design Code
ISO Standard 4437
Quantity
(Note 1)
GENERAL
PROCESS CONDITION
Maximum Design Temperature
deg C
40
Minimum Design Temperature
deg C
15
Design Pressure
barG
System Pressure Rating Class Nominal Diameter
DESIGN & CONSTRUCTION
MATERIAL FUSION COMPABILITY INSPECTION AND TESTING MARKING
#150 mm
4
2
Other
32
SDR Number
11
Joint Length
50 up to 100 long coil
Squeeze off ability
Yes
Fitting Requairement
Yellow
PE Number
80
Material Grade
MDPE
Fusion Compability Test for Butt Joint
(Note 3) and as per ISO 4437
Inspection and Testing
(Note 3)
Handling and Transportation
As per IGEM/G/8 Standard
Design Standard
(Note 3)
Manual Guarantee
1 Year
CERTIFICATE Production and Material Certificate
Note 1. Vendor/Supplier/Contractor to complete 2. Refer to Scope of W ork, Bid Document, or Attachment specified by PGN 3. Shall refer to Standard Teknis and Material - Pipa Polyethylene
Yes
No
6
DATA SHEET PIPE POLYETHYLENE
PT.PGN (Persero) Tbk No. Doc :
Revisi:
Page : 5 dari 5
Location
Onshore
Fluid Service
Natural Gas
Design Code
ISO Standard 4437
Quantity
(Note 1)
GENERAL
PROCESS CONDITION
Maximum Design Temperature
deg C
40
Minimum Design Temperature
deg C
15
Design Pressure
barG
System Pressure Rating Class Nominal Diameter
DESIGN & CONSTRUCTION
MATERIAL FUSION COMPABILITY INSPECTION AND TESTING MARKING
#150 mm
4
2
Other
20
SDR Number
11
Joint Length
50 up to 100 long coil
Squeeze off ability
Yes
Fitting Requairement
Yellow
PE Number
80
Material Grade
MDPE
Fusion Compability Test for Butt Joint
(Note 3) and as per ISO 4437
Inspection and Testing
(Note 3)
Handling and Transportation
As per IGEM/G/8 Standard
Design Standard
(Note 3)
Manual Guarantee
1 Year
CERTIFICATE Production and Material Certificate
Note 1. Vendor/Supplier/Contractor to complete 2. Refer to Scope of W ork, Bid Document, or Attachment specified by PGN 3. Shall refer to Standard Teknis and Material - Pipa Polyethylene
