Controlling a Robotic Car Through MATLAB GUI _ Electronics Project

2/13/2017

C on ontr ol ol lili ng ng A Roboti c C ar ar Thr ou ough M AT ATLAB GU I | El ec ectr on oni cs cs Pr oj oj ec ect

Controlling A Robotic Car Through MATLAB GUI By Saikat Patra, Suman Nag and Shibendu Mahata February 2, 2017

This project presents the implementation of a MATLAB based graphical user interface (GUI) to control the movement of a robotic car. The commands to move the car in forward, reverse, right and left directions are sent from the GUI and processed by Arduino Uno board mounted on top of the car. Authors’ prototype is shown in Fig. 1.

Fig. 1: Author’s prototype of the MATLAB GUI based robotic car

Circuit and working In this project, MATLAB based GUI communicates with Arduino through a USB data cable. You can send commands to Arduino to move the car in a specific direction by pressing the corresponding push button in the GUI. The particular push button, when pressed, executes callback function corresponding to that push button in the MATLAB program, car.m. Within that function, instructions to set/reset the digital I/O pins (10, 11, 12 and 13) of Arduino are executed to drive the car in the desired direction.

Fig. 2: Block diagram for controlling the robotic car through MATLAB based GUI

http://el ectr oni csfor u.com /el ectr oni cs- pr oj ects/contr ol l i ng- r oboti c- car - m atl ab- gui

1/4

2/13/2017

C ontr ol li ng A Roboti c C ar Thr ough M ATLAB GU I | El ectr oni cs Pr oj ect

Fig. 3: Circuit diagram for controlling the robotic car through MATLAB based GUI

Block and circuit diagrams for controlling the robot are shown in Figs 2 and 3, respectively. Arduino Uno board. Arduino Uno is an AVR ATmega328P microcontroller (MCU) based development board with six analogue input pins and 14 digital I/O pins. The MCU has 32kB of ISP flash memory, 2kB SRAM and 1kB EEPROM. The board provides serial communication capability via UART, SPI and I2C. The MCU can operate at a clock frequency of 16MHz. In this project, digital I/O pins 10, 11, 12 and 13 of Arduino are configured as output pins. L293D IC. This

is a dual H-Bridge high-current motor driver IC. This IC is used since the digital pins of Arduino Uno cannot source enough

current to drive the motors of the robotic car. H-bridges are also useful in controlling the direction of rotation of a motor. Enable pins (pins 1 and 9) of the IC being active high are connected to 9V.

READ

Dimming Technology Has Undergone Massive Metamorphosis Since Last Few Years

Four input pins IN1, IN2, IN3 and IN4 of L293D have been connected to digital I/O pins 10, 11, 12 and 13, respectively, of Arduino. Four output pins (OUT1, OUT2, OUT3 and OUT4) of the IC are connected to the two motors (M1 and M2) with their terminals marked as A, B, C and D, respectively, as shown in Fig. 3. On pressing a particular pushbutton in the GUI, digital signals sent from Arduino to L293D are listed in Table I.

Software program Circuit operation is performed using the software program loaded into the internal memory of Arduino board. The program implements all required functionalities including user inputs through MATLAB GUI interface. The steps are listed below: 1. Arduino IDE 1.6.5 is used for programming Arduino Uno. The latest IDE can be downloaded for free from Arduino’s official website. After downloading Arduino IDE, install it. Note the directory of Arduino IDE installation. 2. Download Legacy MATLAB and Simulink Support for Arduino package from MathWorks website. Extract the compressed folder named ArduinoIO. From this folder, copy pde folder and paste it in C:\Program Files (or Program files x86)\Arduino\Libraries (path may be different

http://electronicsforu.com/electronics-projects/controlling-robotic-car-matlab-gui

2/4

2/13/2017


depending on the installation directory of the IDE).

After pasting pde folder in correct location, open Arduino IDE. If you have pasted the folder in correct location, you would find pde in File→Examples →pde. Open the code by File →Examples →pde→ adioes. 3. Connect Arduino Uno board to your PC. From Device Manager, note the COM port at which Arduino Uno board is installed. From Tools menu in Arduino IDE, select the board as Arduino Uno and select the COM Port number noted earlier. Upload adioes code to Arduino Uno board by pressing Upload button in the IDE.

READ

World's Top 20 Robotics Project Ideas

4. Copy the entire contents of the extracted ArduinoIO folder to a folder in My Documents (For Windows PC). 5. Our application program has been developed in R2014a version of MATLAB. After installing this version of MATLAB in your PC, open install_arduino.m file present in the directory where you have copied the contents of ArduinoIO folder. Now, run install_arduino.m file. This code will correctly install and save the path of Arduino support package. 6. Open the source code file for this project titled car.m. Edit the COM port [in the line a=arduino(‘COM9’)] with the port number in your PC where Arduino Uno board has been installed. After running the file, MATLAB will try to communicate with the board. After successful communication is established, you can control the robot by pressing the appropriate pushbutton in the GUI.

Constructing and testing An actual-size, single-side PCB for the circuit controlling the robotic car using MATLAB based GUI using Arduino is shown in Fig. 4 and its component layout in Fig. 5. Suitable connectors are provided on the PCB for input (CON1) from Arduino and output (CON2 and CON3) for motors.

Fig. 4: Actual-size PCB pattern for the circuit to control the robotic car

Fig. 5: Component layout of the PCB

Download PCB and component layout PDFs: click here Download source folder: click here


3/4

2/13/2017


Assemble the robotic car by connecting two motors, two wheels (rear) and a castor wheel (front). Connect the circuit as per the circuit diagram shown in Fig. 3. Connect the battery with correct polarity; otherwise you might end up damaging Arduino board and L293D. For troubleshooting, check the voltages at various test points given in Table II.

READ

Solid State Drives (SSDs) In, Hard Disk Drives (HDDs) Out!

Shibendu Mahata is M.Tech (gold medallist) in instrumentation and electronics engineering from Jadavpur University. Currently, he is pursuing Ph.D from NIT, Durgapur. He is interested in MCU based real-time embedded signal processing and process control systems Saikat Patra is passionate about electronics and MCU based embedded system applications Suman Nag enjoys electronics and likes to read about wireless sensor networks


4/4

Controlling a Robotic Car Through MATLAB GUI _ Electronics Project

Recommend Documents