Express Instruction 1. Launch NMS Utility Double click on the NMS shortcut icon on the desktop to launch the NMS utility first.
2. Choose Mode If it has no modem, and connects to repeater directly, directly, it will approach to the Local control Mode.
Or if it connects with the Modem, it will approach to the Remote control Mode.
Main Windows Windows lists as below picture:
3. Create Sites Follow the steps in turns to create: Region a.
Right click on the any area of the „Region‟,
b.
“Create
District
Site
Sites”, then click on „Add Region(R)‟ to create
supposed named as “China”.
Right click on the Region‟China‟, and then click on „Add District‟t o create the District, supposed named as ‟F ujian. ‟
c. Right click on the District „Fujian‟ , and then click on
„Add
Site‟ to create the Site, supposed
named as‟Xiamen „.
4. Fill Site Information After created the Site, then launch the site information management window for filling. a.
Right click the Site „Xiamen‟, then click the „Equipment Basic Info(I)‟ to launch the Site Information management window. window.
①
②
③
Site Information window
① Firmware Ver.: Firmware version. ② Backup Battery: It is available only when the system has Backup Battery Unit. ③ Applicable in GSM, DCS, WCDMA, CDMA: Select the wanted system, supposed GSM, then its following Selective‟ mode will be available to selection, the off
„Channel
„Band
Selective ‟ or
„Channel
Nr. ‟ Item is only available after tick
Channel Selective mode.
Above operation same to DCS /WCDMA/CDMA system system for selection. Note: Channel Nr is a full name of Channel Number. Only available under tick off the channel selective mode, and it shows that the repeater provided configurable configurable Channel quantities.
Below Instructions A suitable for the repeaters with SN : (SN:12040038, 12040039, 12040040, 12040047, 12040048, 12040049, 12040050, 12040051, 12040052, 12040053, 12040054, 12040055, 12040070, 12040071, 12040072, 12040073, 12040074, 12040075). E.g: Instructions to set parameters for GSM&DCS Dual bands Pico repeater with output power 20dBm, 3 tunable sub-bands(GSM:2 tunable sub-bands for DL; DCS:1 tunable sub-band for DL), corresponding site named as Xiamen:
A.1. create site name first as above steps of „3.create site‟. A.2. Set general initial parameters for repeater, the steps as following:
① Select correct Equipment_T Equipment_Type ype as: Digital Band Selective Selective Repeaters system (Do not select WCDMA ,CDMA while while the repeater does not ② Select the GSM,DCS system includes these two systems).
③ Select the „Channel Selective ‟i tem both on GSM and DCS systems. ④ Set Channel Nr as 4 for GSM system (because (because GSM system has 2 tunable sub-bands) , and set Channel Nr as 2 for DCS system (because DCS system has only 1 tunable sub-band) parameters are setting complete, complete, then click the button „Modify(M)‟ ⑤ After all the parameters
⑥ Click the button „Done(D)‟t o finally confirm all the setting.
.
A.3. Set detailed Parameters on each Systems (GSM &DCS) A.3.1 open the Local console window Double Click the corresponding created site name in the Main Window or right click the created site name and then click „RF / Status(S)‟ window. window.
Refer to
to launch
„Local / Remote Console‟
Pic2 Local Console Window
Local Console window Note: after above general initial parameters parameters setting, the support systems systems will tick off on the GSM GSM &DCS, other systems are not available to choose, unless return to Step A.2 to reset the requested system. A.3.2 Read the repeater detailed Parameters Parameters in support system (GSM/DCS) Recommend to read the repeater history information before set parameters. Click the Monitoring sheet and then click the R F/Status sheet then:
① Select support system(GSM/DCS) ② click button „Get RF/Status‟t o read the history information.
A.3.3 Set the repeater RF/Status RF/Status Parameters in support systems (GSM/DCS),refer to Pic3 Click the Configuration sheet and then click the RF/Status sheet then:
①
Select support system(GSM/DCS)
②
click button „Get RF/Status‟t o read the history information
③
Set the th e wanted wan ted status s tatus and parameters p arameters for PA ,PA ,PA ATT ,LNA ATT, ATT, O/P Power Threshold, AGC AGC Enable, Max Gain as which lists on the Pics3
④
After set each parameters then click the „Set‟b utton to save it.
Set Parameter in the Local Console Window A.3.4 Set Channel numbers for tunable Sub-bands
in support
Systems (GSM/DCS)
A.3.4.1 Set Channels numbers for 2 tunable Sub-bands(both for UL&DL) in GSM System: Click the Configuration sheet and then click the Channel sheet then:
① Select support system(GSM) ② Set requested requested Channels numbers numbers for for 2 tunable sub-bands sub-bands in W1~W4 W1~W2: for first tunable sub-band; W1 is the starting channel number,W2 is the end channel number W1&W2 combined parameters to set the request frequency range in first tunable sub-band. W3~W4: for second tunable sub-band W3 is the starting channel number,W4 is the end channel number W3&W4 combined parameters to set the request frequency range in second tunable sub-band.
③ Switch ON the 2 tunable sub-bands Just switch W2 and W4 as ON ,else W1&W3 as OFF. OFF.
④ W1-2 &W3-4 will Automatically display the frequency corresponding to the channel numbers which set in W1&W2,W3&W4 please refer to below Set Channel number s for GSM tunable tunable sub-band
Set Channel number s for GSM tunable sub-band
A.3.4.2 Set Channel number for fixed bandwidth(for UL) and 1 tunable Sub-bands(for DL) in DCS System: Click the Configuration sheet and then click the Channel sheet then:
① Select support system(DCS) ② Set fixed bandwidth for UL Just set the requested central frequency channel number in W1
③ Set 1 tunable sub-band for DL Just set the requested starting channel number in S1 and end channel number in S2
Note: keep the channel switch as default .
Set channel numbers for DCS system Note: After set all the parameters, recommend return to Monitoring RF/Status page to determine the setting parameters.
Below Instructions B suitable for the repeaters with SN : (SN:12040041, 12040042, 12040043, 12040044, 12040045, 12040046, 12040056, 12040057, 12040058, 12040059, 12040060, 12040061, 12040062, 12040063, 12040064, 12040065, 12040066, 12040067, 12040068, 12040069) E.g: Instructions to set parameters for GSM&DCS Dual band Pico repeater with output power 20dBm, 3 Fixed sub-bands(GSM:2 Fixed sub-bands for UL&DL; DCS:1 Fixed sub-band for UL&DL), corresponding site named as Xiamen:
B.1. create site name first as above steps of „3.create site‟. B.2. Set general initial parameters for repeater, the steps as following:
① Select correct Equipment_T Equipment_Type ype as: Band Selective Repeaters Repeaters system (Do not select WCDMA ,CDMA while while the repeater does not ② Select the GSM,DCS system includes these two systems).
③ Select the „Channel Selective ‟i tem both on GSM and DCS systems ④ Set Channel Nr as 2 for GSM system (because (because GSM system has 2 Fixed sub-bands) , and set Channel Nr as 1 for DCS system (because DCS system has only 1 fixed sub-band) parameters are setting complete, complete, then click the button „Modify(M)‟ ⑤ After all the parameters
⑥ Click the button „Done(D)‟t o finally confirm all the setting. please refer to below below < Pic1> Site Information Information management management
< Pic1> Site Information management
B.3. Set detailed Parameters on each Systems (GSM &DCS) B.3.1 open the Local console window Double Click the corresponding created site name in the Main Window or right click the created site name and then click „RF / Status(S)‟ to launch window. window.
„Local / Remote Console‟
Refer to Pic2 Local Console Window
Local Console window Note: after above general initial parameters parameters setting, the support systems systems will tick off on the GSM GSM &DCS, other systems are not available to choose, unless return to Step A.2 to reset the requested system. B.3.2 Read the repeater detailed Parameters Parameters in support system (GSM/DCS) Recommend to read the repeater history information before set parameters. Click the Monitoring sheet and then click the R F/Status sheet then:
① Select support system(GSM/DCS) ② click button „Get RF/Status‟t o read the history information.
B.3.3 Set the repeater RF/Status RF/Status Parameters in support systems (GSM/DCS) Click the Configuration sheet and then click the RF/Status sheet then:
①
Select support system(GSM/DCS)
②
click button „Get RF/Status‟t o read the history information
③
Set the th e wanted wan ted status s tatus and parameters p arameters for PA ,PA ,PA ATT ,LNA ATT, ATT, O/P Power Threshold, AGC Enable, Max Gain as which lists on the Pics3
④
After set each parameters then click the „Set‟b utton to save it.
Set Parameter in the Local Console Window
B.3.4 Set Channel numbers for Fixed Sub-bands
in support
Systems (GSM/DCS)
B.3.4.1 Set Channels numbers for 2 fixed Sub-bands(both for UL&DL) in GSM System: Click the Configuration sheet and then click the Channel sheet then:
① Select support system(GSM) central frequency channel numbers for for 2 fixed sub-bands in ② Set requested central UL1&DL1, UL&DL2 UL1&DL1: for first fixed sub-band; UL1 is the central frequency channel number for uplink DL1 is the central frequency channel number for downlink, UL1&DL1 combined parameters to set the request frequency range in first fixed sub-band. UL2&DL2: for second fixed sub-band; UL2 is the central frequency channel number for uplink DL2 is the central frequency channel number for downlink, UL2&DL2 combined parameters to set the request frequency range in second fixed
sub-band Keep channel Switch parameters as default. Please refer to below Set Channel numbers for GSM 2 fixed sub-band
Set Channel numbers for GSM 2 fixed sub-band
B.3.4.2 Set Channel number for 1 fixed bandwidth(for UL&DL) UL&DL) in DCS System: Click the Configuration sheet and then click the Channel sheet:
①Select support system(GSM) ②Set requested central frequency channel numbers for 1 fixed sub-bands in UL1&DL1 UL1&DL1: for the fixed sub-band; UL1 is the central frequency channel number for uplink DL1 is the central frequency channel number for downlink, UL1&DL1 combined parameters to set the request frequency range in the fixed sub-band. Keep channel Switch parameters as default Pleaser refer to Set Channel numbers for DCS 1 fixed sub-band
Set Channel numbers for DCS 1 fixed sub-band Note: After set all the parameters, recommend recommend return to Monitoring RF/Status page to determine the setting parameters.
Below Instructions C suitable for the repeaters with SN : (SN:12040076, 12040077, 12040078, 12040079, 12040080, 12040081, 12040082, 12040083, 12040084, 12040085) E.g: Instructions to set parameters for UMTS Single bands Pico repeater with output power 27dBm, corresponding site named as Xiamen:
C.1. create site name first as above steps of „3.create site‟. C.2. Set general initial parameters for repeater, the steps as following:
① Select correct Equipment_T Equipment_Type ype as: MicroRepeaters WCDMA system (Do not select other systems systems while the repeater does not ② Select the WCDMA includes them).
③ Select the „Band Selective‟item on WCDMA systems ④ After all the parameters parameters are setting complete, complete, then click the button button „Modify(M)‟ ⑤ Click the button „Done(D)‟t o finally confirm all the settings. please refer to below below < Pic1> Site Information Information management management
Site Information Management
C.3 open the Local console window
Double Click the corresponding created site name in the Main Window or right click the created site name and then click „RF / Status(S)‟
to launch
„Local / Remote Console‟
window.
C.4 Set Set Channels numbers for 1 fixed Sub-bands(both for UL&DL) in WCDMA System
① Select support system(WCDMA) Set requested central frequency channel numbers in UL1&DL1 UL1 Center Fre(KHz):is the central frequency channel number for uplink DL1 CenterFre(KHz): CenterFre(KHz): is the central frequency channel number for downlink, UL1&DL1 combined parameters to set the request frequency range for fixed sub-band. Set fixed bandwidth for WCDMA
Set fixed bandwidth for WCDMA Note: After set all the parameters, recommend recommend return to Monitoring RF/Status page to determine the setting parameters.
