Descripción: La Red Óptica Pasiva con Capacidad de Gigabit (GPON o Gigabit-capable Passive Optical Network en inglés) fue aprobada en 2003-2004 por ITU-T en las recomendaciones G.984.1, G.984.2, G.984.3, G.984....
Conf EnvejecimientoIII. Paso Cr III a VIDescripción completa
OLT SPLITTER ONTDeskripsi lengkap
Descripción completa
Huawei MA5683T configuration instructions part 1 1.1 Opening / / through the console,login user name root,password admin.If the device is a twinengine,connect bright green light board ACT. MA5683T>enable //open the privilege MA5683T#config //Enter the terminal configuration mode MA5683T(config)#sysnameSJZ-HW-OLT-1 MA5683T(config)#sysnam eSJZ-HW-OLT-1 //device-naming (Usually when to start the configuration) //Creation telnet user MA5683T((config) #terminal user name //Add user operation huawei MA5683T User Name(length<6,15>):huawei Name(length<6,15>) :huawei //Setting the user name User Password(length<6,15 Password(length<6,15>):huawei123 >):huawei123 //Required to enter your password. Enter part of the actual not visible Confirm Password(length<6,15> Password(length<6,15>):huawei123 ):huawei123 // Verification the password again User profile name(<=15 chars)[root]:root //nter the user management level User's Level: 1. Common User 2. Operator 3. Administrator:3 Administrator: 3 //Select the user permissions Permitted Reenter Number(0--4):1 //Set the user name can repeat logins, general requirements for 1 times. User's Appended Info(<=30 chars):HuaweiAdm //Add a description, not set. Adding user user succeeds succeeds Repeat this this operation? operation? (y/n)[n]: (y/n)[n]: //After if you want to start or insert a new board need the following,autofind is newly inserted PoC board MA5683T(config)#display board 0 //Check the equipment state of board,the most commonly used commands. ------------------------------------------------------------------------SlotIDBoardNameStatus SubType0 SubType1 Online/Offline --------------------------------- -------------------------------------------------------0 1 H802EPBD Normal 2 H802EPBD Normal 3 H802EPBD Normal 4 H802EPBDAuto_find 5 6 H801SCUNActive_normal 7 H801SCUNStandby_normal 8 H801GICF Normal 9 H801X2CA Normal 10 11 12 13 ------------------------------------------------------------------------MA5683T((config)#board confirm 0 //To automatically MA5683T automaticall y discover board, need to be confirmed after a board can be used. //For the board is unconfirmed board of hardware running indicator light is ，
normal,but the PoC port doesn't work. 1.2 manage configuration 1 Create and management VLAN MA5683T(config)#vlan 5 smart 2 Uplink port bypass and management VLAN MA5683T(config)#port vlan 5 0/8 0 3 Configure the IP address MA5683T(config)#interface vlanif 5 MA5683T(config-if-vlanif5)#ip address 10.11.126.2 255.255.0.0 MA5683T(config-if-vlanif5)#quit 4 Configuration management gateway MA5683T(config)#ip route-static 0.0.0.0 0.0.0.0 10.11.0.1 • //• If the 0/8 0 port is connected, you can use the huawei123 telnet this address Huawei landing. If you need network management software management, then you need to add the following command MA5683T(config)#snmp-agent community read public 、
、
、
、
、
1.3 Create and uplink transmission PoC VLAN MA5683T(config)#vlan 5 smart MA5683T(config)#vlan 14 smart MA5683T(config)#vlan 999 smart • MA5683T(config)#vlan 183 smart MA5683T(config)#vlan 3049 to 3098 smart MA5683T(config)#port vlan50/8 0 • MA5683T(config)#port vlan140/8 0 MA5683T(config)#port vlan9990/8 0 MA5683T(config)#port vlan3049 to 30980/8 0 y MA5683T(config)#port vlan140/8 1 MA5683T(config)#snmp-agent community write private 、
CONFIGURACIÓN OLT HUAWEI – CONFIGURACIONES IMPORTANTES MCUD = Tarjeta donde se encuentran los transceiver y los puestos de control y consola de la olt
SCUN: Tarjeta de control de ancho de banda
La tarjeta de control de la OLT HUAWEI tiene una ip por defecto la cual es: 10.11.104.2/24, Las credenciales de acceso son Login: root, password: admin123
Conectado en el puerto de consola (CON) y editar la IP de administración en la vlan administrativa VLAN ID 10 enable config vlan 10 smart vlan 10 description “Management” port vlan 10 0/8 0 interface vlanif 10 ip address 192.168.10.2 255.255.255.0 quit ip route-static 0.0.0.0 0.0.0.0 192.168.10.1
una alternativa para la administración es cambiar la ip de gestión de la interfaz meth interface meth0 Ip address 192.168.1.2 24 Quit
Ejemplo configuración de Tiempo
Ejemplo de exportación de configuración con ftfp server
Backup configuration tftp 10.11.104.1 old_config.cfg Backup data tftp 10.11.104.1 old_data.dat Backup bios tftp 10.11.104.1 old_bios.bin Backup program tftp 10.11.104.1 old_program.efs
Ejemplo de reinicio de configuración
Erase flash data active/standby
Agregar nuevas tarjetas de conexión con la OLT
