Powerscreen Powerscreen International. International. Dist. Ltd. Coalisland Road, Dungannon, Co.Tyrone, N.Ireland BT71 4DR Tel: +44(0) 28 87 740701 Fax: +44(0) 28 87 746569 Email:
[email protected]
INTRODUCING THE
CH I E F T AI N 600
Chieftain 600 Technical Specification CHIEFTAIN 600 24-01-2007
Page 2
FEATURES • • • • • •
Length (transport) Height (transport) Height (transport) Hopper capacity(inc.grid) Screenunit Powerunit
12.45m (40’ – 6”) 3.5m (12’ – 11”) W 3.2m (10’ – 4”) T 4.6m3 ( 6 cu yds) 4 – bearing 2.44m x 1.22m (8’ x 4’) 4 cylinder Diesel 55kW (74 Hp)
Weight on axle:10.84Tonne Weight on kingpin:3.2Tonne Total Wheel Machine Weight:14.04T
A D V A N T A G E S • • • •
• • •
• •
Medium capacity up to 200 TPH, (depending on mesh sizes and material type). Quick set up time typically under 15 minutes. Maximum mobility with heavy duty, low ground pressure crawler tracks. T Maximum mobility with fifth wheel, jacking legs, road wheels, springs, brakes and mudguards. W Removable heavy duty pendant remote control system. T Optional radio control system available if required at ex tra cost. T High performance hydraulic system – Cast iron pumps and motors c/w hydraulic oil cooler. Angle adjustable tipping grid with radio control double acting tipping grid rams. Single shaft shredder.
A P P L I C A T I O N S • • • • •
Sand and gravel Topsoil Coal Crushed stone Recycling
OP E R A T I N G P R E S S U R E S • • • •
Sides & Tail conveyor Screen unit Main conveyor Feed conveyor
2400 Psi ( 165 bar ) 1200 Psi ( 83 bar ) 600 Psi ( 41 bar ) 200 Psi ( 14 bar )
All specifications subject to change without prior n otice.
Chieftain 600 Technical Specification CHIEFTAIN 600 24-01-2007
Page 3
NB – W = Wheel Machine / T = Track machine
H o p pe r & G r i d: Adjustable angle tipping grid with integral loading and wing plates Grid opening 2.95m x 1.46m (9’-8” x 4’-9½”) Grid aperture: 102mm (4”) Grid option: 152mm (6”) Target area: 3.66 x 1.7m (12’ x 5’-7”) Hopper capacity: 4.6m3 (6 cu. yds)
S c r ee nuni t: 8’x4’ (2.44x1.22m) double deck 4 bearing positive action screenunit.
Feeder: The hopper has a continuous belt feed to the main conveyor. The belt is 3 ply, 800mm (32”) wide and is driven by a hydraulic motor with variable speed adjustment to determine the feed rate.
M ai n C onvey or : The conveyor is 3 ply, 800mm (32”) wide and carries the material from the feeder to the screenunit.
Tail Conveyor: 1050mm (42”) wide 2 ply hydraulically folding t ail conveyor 3.43m (11’ – 3”) stockpile height. (Measured to drum centre)
S i de C onvey or s : 650mm (26”) 3 ply wide hydraulically folding side conveyors with variable speed control: 3.44m (11’ – 3½”) stockpile height. (Measured to drum centre)
T y p i c a l S p e e ds : Main Conveyor Tail Conveyor Feed Conveyor Side Conveyor 1 Side Conveyor 2
60 rpm 140 rpm 0 - 20 rpm 0 - 200 rpm 0 - 200 rpm
All specifications subject to change without prior n otice.
Chieftain 600 Technical Specification CHIEFTAIN 600 24-01-2007
Page 4
NB – W = Wheel Machine / T = Track machine
P o w e r u n i t & H y dr au li c s : Diesel engine: Pump1:
77 kW (85 Hp) developing 55 kW (74 Hp) at 2300 rpm. Cast iron triple pump each circuit 27cc/rev Giving a Flow of 62 l/min (13.6 Gal/min) Cast iron motor 160cc/rev Cast iron motor 500cc/rev Cast iron motor 400cc/rev Cast iron motor 315cc/rev Cast iron motor 51.8cc/rev
Feeder Motor: Main conveyor Motor: Tail Conveyor Motor: Side Conveyor Motor: Screen Motor:
T a n k C a pa c i t i e s : Hydraulic tank: Diesel tank:
C r a w le r T r a c k D a t a:
500 L (110 Gal) 143 L (31 Gal)
T
Tractive Effort Gradability Percentage Gearbox Ratio Hydraulic Motor Approximate Speed Total flow per Track
R o ad T r a n s p or t :
= = = = = =
9268 daN 90 % 40 Degrees 1:134 32 cc/rev 1.25 Km/hr (0.78 Mph) 62 Ltrs per min
W
Wheels: Axle: Suspension: Brakes: Mudguards: Lateral Protection: Lights:
285/70/R19.5 Approved braking twin axle Leaf spring Air brakes, (ABS optional) Plastic type Optional extra. Optional extra.
S hr edde r O pt i on Motor: Circuit:
Cast iron motor 51.8 cc/rev Coupled to Feeder conveyor circuit.
All specifications subject to change without prior n otice.
Chieftain 600 Technical Specification CHIEFTAIN 600 24-01-2007
Page 5
NB – W = Wheel Machine / T = Track machine
All specifications subject to change without prior n otice.
!"#$%&"' )** %+&, -.+,"'/ 0"1#'2".'2
! " # $ % & " ' ) * * + ! # # , % - & ' . / 0 - % 1 " 2 # ' . " 0 ' .
!"#$%&"' )** +!##, +-./"'0 1"2#'3"-'3
