Belt Grinder Plans v 1

Belt Grinder -Backbone make one weld together, 4 places

¼” x 2" flat bar

cut a 1/16" x ¾” clearance slot the entire length on the inside of the ½” x 2" flat bar

½” x 2" flat bar

2.030"

tap ½-20

0.530"

¼” x 2" flat bar

file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

¼” x 2" flat bar

Belt Grinder -Bearing Plate make one Bearing Plate, 3/8" f;at bar. weld the Backbone to the Bearing Plate

take appropriate steps so that after welding this angle is precisely 90 degrees since it affects belt tracking

drill appropriate pattern to mount two pillow block bearings to the plate

6.000"

7.000"

file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Tracking Arm Bracket make one

take appropriate steps so that after welding this angle is precisely 90 degrees since it affects belt tracking

drill 0.500" 0.750"

6.500"

file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

weld ½” x 2" flat bar to the frame to form the tracking arm bracket

Belt Grinder -Pedistal make one

1-1/2" square tubing with 3/16" or 1/4" wall

drill and tap square tubing ½-20, then weld nut over the hole to increase the number of threads weld 1" x 0.250" wall DOM tubing to square tubing.

2.000" 8.000" 33.000"

Belt Grinder -Backbone and Pedistal Assembly make one

weld Backbone to Pedistal

Belt Grinder -Stand make one

10.000"

1-½” square tubing with 3/16" or ¼” wall

electrical switch box

1" square bar

18.000"

10.000"

10.000"

file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

10.000"

Belt Grinder -Tracking Adjustment Block make one ½” x 4" flat bar

drill 0.250", 2 places 1.000"

1.000"

1.000"

1.000"

0.500" 0.750"

3.000"

tap 3/8-24

3.500"

file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Tracking Adjustment Lever make one

weld 1/2" x 1-½” flat bar to Tracking Adjustment Block

drill 0.500" tap ¼-20

1.500" 8.000"

file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Tracking Adjustment Arm make one

1.125" ½” x 2" flat bar, 2 places

drill 0.250"

tap ½-13

weld two pieces together

0.250"

1.500"

3.000"

1.000"

file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

1.000"

Belt Grinder -Vertical Platen Frame make one 3/8" x 6" flat bar

tap ½-13, 3 places 3/8" radius, drill 0.750"

1/4" radius, drill 0.500"

Tap 3/8-16, 4 places

drill 0.500"

1.250" 2.250"

3.875" 4.250" 5.000" 5.750"

0.750" 1.125" 1.500" 1.750" 2.250" 3.000" 4.000" 6.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Tool Rest make one

2.500" cut away this area

3" angle iron with ¼” wall

0.750"

0.750" tap ½-13 then weld a nut over the hole to increase the number of threads

file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Tool Rest Support Arm make one

round end, 2 places

½” square bar, 4 places, welded together drill 0.500"

0.750"

2.500" 8.750"

9.500"

file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Vertical Platen Extension Arm make one

½” x 2" flat bar tap ½-13, 2 places

2.500" 21.000"

file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Platen Clamp make one

3/8" x 1-½” flat bar drill 0.500", 2 places

2.500"

4.000"

file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Motor Mount make one drill 0.375". 4 places 1.750" 0.750"

2.250"

7.000"

drill 0.500", 2 places

¼” x 1" flat bar, 4 places

1.000"

4.875"

6.875"

file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Vertical Platten Bracket make two

tap ¼-20 and countersink

1.000"

1.50"

1.000"

5.000"

file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Vertical Platten make one

countersink all the way through, 2 places

6.000"

¼” x 2" flat bar of stainless steel or other wear resistant material 4.250"

1.750"

1.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

1.000"