BD Service Tool Manual GAA30082DAC 2009-11-30

OTIS

Software Basic Data

Engineering Center Berlin

MCS –LCB_II

No.: GAA30082DAC_STM SCN: GAA30082DAC

Service Tool Manual

Page: 1/ 65 Date: 2008-11-06

MC S – L C B I I , TC B , HC H C B , TC B C GCS - GE CB S ervi er vicc e Tool To ol Manu Manua al

Applicable for:

LCB_II: TCB: HCB: TCBC: TCBC: GECB:

Document Revision : Date 2008-11-06

GAA 30082 CAA - GAA 30082 DAC GAA 30084 BAB - GAA 30084 CAB GAA 30084 BAB GAA 30081 AAC - GAA 30081 AAF GAA 30781 AAA - GAA 30781 AAF GAA 30780 AAB - GAA 30780 BAA

V 1.0

SCN GAA30082DAC

Author M. Hoinkis

Comment original document

Copyright 2008, OTIS GmbH & Co. OHG Berlin. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of OTIS.

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 2/ 65 Date: 2008-11-06

Table Table of Conte C ontents nts 1 2 3

Revision History...............................................................................4 History ...............................................................................4 Introduction ......................................................................................5 System Menu ....................................................................................6 3.1 3.2 3.3 3.4 3.5

Navigation............................................................................................................6 Entries Entries (dynamic (dynamic)) ....................... ................................... ........................ ........................ ........................ ........................ ....................... .............6 ..6 Multiple SVT Connection............ Connection ........................ ......................... ......................... ......................... .......................... ...................... ......... 7 System Level Msg.: connection to OCSS is not available.................... available........ ....................... ........... 7 System Level Msg.: a subsytem is not available........... ........................ ............ ....................... ........... 7

4

Tree Structure ..................................................................................8 4.1 4.2

5

Key Overview........................ Overview............ ........................ ........................ ........................ ........................ ......................... ......................... .................. ...... 9 Short Keys Keys ...................... .................................. ........................ ....................... ....................... ........................ ....................... ....................... ...............9 ...9

Menu Functions of the Service Tool.............................................11 Tool .............................................11 5.1

5.1.1 5.1.2 5.1.3 5.1.4 5.1.5 5.1.6 5.1.7 5.1.8 5.2

5.2.1 5.2.2 5.2.3 5.2.4 5.2.5 5.2.6 5.3

5.3.1 5.3.2 5.3.3 5.3.4 5.3.5 5.3.6 5.3.7 5.4

5.4.1 5.4.2 5.4.3 5.4.4

Status Functions Functions........... ...................... ...................... ...................... ....................... ....................... ...................... ....................... .................11 .....11

Status Display M - 1 - 1 - … ....................... ........... ........................ ........................ ........................ ......................... ..................... ........ 12 Status Calls Menu S8 / M - 1 - 1 - 1 ........................ .................................... ......................... ......................... ................13 ....13 Status Inputs Menu S7 / M - 1 - 1 - 2............. 2.. ....................... ........................ ....................... ....................... ................. .....15 15 Status Outputs Outputs Menu M - 1 - 1 - 3 ........................ .................................... ........................ ......................... ......................16 .........16 Status Group Group Menu M - 1 - 1 - 4 ....................... ................................... ........................ ........................ ........................ ..............17 ..17 Status ICSS Menu M - 1 - 1 - 5 ........................ ............ ........................ ........................ ........................ ........................ ............... ...18 18 Status Command Command Menu Menu M - 1 - 1 - 6 ....................... ................................... ......................... ......................... ..................19 ......19 Status Drive Drive Menu Menu (TCBC, GECB only) only) M - 1 - 1 - 7 ....................... ............ ....................... ................... ....... 21 Test Functions............. ......................... ............ ......................... ......................... .......................... ......................... ....................... ........... 22

Test Events Menu S6 / M - 1 - 2 - 1............. 1. ........................ ........................ ........................ ........................ .................. ......23 23 Test Diagnostics Menu M - 1 - 2 - 2 ....................... ........... ........................ ........................ ........................ ..................... ......... 25 Test Part-No Part-No Menu M - 1 - 2 - 3 ........................ .................................... ........................ ........................ ........................ ..............27 ..27 Test RSL Menu Menu M - 1 - 2 - 4 ....................... ................................... ........................ ........................ ........................ ....................28 ........28 Test Selftest Selftest Menu M - 1 - 2 - 5 ........................ .................................... ........................ ........................ ........................ ..............31 ..31 Test Plug Menu M - 1 - 2 - 6 ......................... ..................................... ........................ ........................ ........................ ..................33 ......33 Setup Functions Functions............ ....................... ...................... ...................... ....................... ....................... ...................... ....................... .................35 .....35

Setup Install Menu S4 / M - 1 - 3 - 1 ....................... ........... ....................... ....................... ........................ .................... ........ 36 Setup RSL Menu Menu S5 / M - 1 - 3 - 2 ........................ .................................... ........................ ........................ ....................37 ........37 Setup Allowed Mask Menu M - 1 - 3 - 3 ....................... ........... ....................... ....................... ........................ ................ ....39 39 Setup Position Position Indicator Indicator Menu Menu M - 1 - 3 - 4 ....................... ................................... ........................ .....................45 .........45 Setup DCS-Run Menu M - 1 - 3 - 5................ 5.... ........................ ........................ ........................ ........................ ................. .....46 46 Setup ELD Menu Menu M - 1 - 3 - 6 ....................... ................................... ........................ ........................ ........................ ..................49 ......49 Setup Speech Menu (LCB2 only) M - 1- 3 - 7 ....................... ........... ........................ ........................ .................. ......55 55 Tools Functions Functions ....................... .................................. ...................... ....................... ....................... ...................... ...................... .................56 ......56

Search Search IO M - 2 - 1 ........................ .................................... ........................ ........................ ......................... ......................... ....................57 ........57 Erase IO M - 2 - 2 ......................... ..................................... ........................ ........................ ........................ ........................ ......................58 ..........58 Setup Inst Inst M - 2 - 3 ........................ .................................... ........................ ........................ ........................ ........................ .....................59 .........59 Setup Door M - 2 - 4 ......................... ..................................... ........................ ........................ ........................ ........................ .................60 .....60

OTIS

Software Basic Data


MCS –LCB_II

5.4.5 5.4.6 5.4.7 5.4.8 5.4.9


Service Tool Manual

Page: 3/ 65 Date: 2008-11-06

Show History History (TCB (TCB only) only) M - 2 - 5 ....................... .................................. ....................... ........................ ....................... ............61 .61 Check Config Config M - 2 - 6 ...................... .................................. ....................... ....................... ........................ ....................... ...................62 ........62 Smart Button Program (LCB2 only) M - 2 - 6 ....................... ........... ........................ ........................ ................... .......63 63 Smart Button Test (LCB2 only) M - 2 - 7................. 7..... ....................... ....................... ........................ ..................... ......... 64 Operate Operate Memory Memory M - 2 - 9 ....................... ................................... ........................ ........................ ........................ .......................65 ...........65

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 4/ 65 Date: 2008-11-06

1 R evis ion His tory Date 14-Mar-2002

SCN GAA30082CAB

Author A. Gerwing

21-Nov-2003

GAA 30082 CAC

A. Pfeffer

07-Sep-2004 14-Dec-2004 06-Jan-2005 2005-02-18 2005-02-25 2005-02-28 2005-07-21

GAA 30781 AAA GAA 30781 AAB G15 30780 AAA G22 30780 AAA G22 30780 AAA G2230780AAA GAA 30780 AAB

M. Hoinkis M. Hoinkis A. Pfeffer A. Pfeffer H.-K. Spielbauer A. Pfeffer A. Pfeffer

2005-07-21 2005-11-04 2006-01-17 2006-11-30 2007-01-12

GAA30780AAB Gxx30781AAE

H.-K. Spielbauer D. Cominelli M. Hoinkis H.-K. Spielbauer M. Hoinkis

Comment first issue; also applicable for TCB, TCBC and HCB M126, M137 added; Status Display corrected; minor corrections added TCBC 30781 baseline Loader SCN (part menu) also applicable for GECB board versions for SHO/WCO corrected Selftest updated Selftest updated GECB: Compass added: M111, M115, M1331 Update for Compass Release Test-Event with new time stamp cut call mask; DIAG ACT-T; SCN update System Menu with ARO

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 5/ 65 Date: 2008-11-06

2 Introduction The Service Tool is a pocket terminal that lets you control all elevator functions:  Monitoring of software states, system inputs and outputs and system messages  Setup of installation parameters  Use of software tools. The access of each function is controlled by the Menu System which allows convenient work with the Service Tool. The Service Tool Manual describes the Menu System and the single Service Tool functions.

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 6/ 65 Date: 2008-11-06

3 S ys tem Menu The System Menu is not available at the LCB_II The System Menu is an overview of all components which are connected at the CAN bus and have a SVT menu.

3.1 Navig ation The System Level-Menu can be entered in 2 ways: 1. by connecting physically the Service Tool onto any Service Tool plug 2. pressing the Module key twice out of a subsystem menu M-M

Selection of the MCS220-C Gen2 System Level-Menu

GoOn

go to second page of System Level-Menu (if more than 4 menus detected)

3.2 E ntries (dynamic) 1:OCSS 2:DRIVE> 3:FDOOR 4:RDOOR>

1: OCSS

TCBC or GECB

2: DRIVE

MCBIII or GDCB

3: FDOOR

front DCSS5 via CAN or Multidrop

4: RDOOR rear DCSS5 via CAN or Multidrop 5: SPBC

SPBC, SPBC_II, SPBC_III

6: RMH

REM5 (connected at OCSS SVT plug

7: LWB

LWB_II

9: ARO

external ARO

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 7/ 65 Date: 2008-11-06

3.3 Multiple S VT Connection Multiple SVT connections can be established by connecting the SVT to any local Service Tool plug (e.g., MCBIII, …) and by selecting the same subsystem in the SVT menu. Note: TCBC SVT menu access must be the final connection, otherwise it will be discon-

nected by other connections. An earlier SVT connection will be disconnected by any other SVT connection. Following SVT display will indicate this: disconnected . by other SVT .

3.4 S ys tem Level Ms g .: connection to OC S S is not available waiting . for SYSTEM MENU .

If the TCBC/GECB is not available, you will see this message for 6 seconds. Then the SVT will switch automatically into the local SVT menu.

3.5 S ys tem Level Ms g .: a s ubs ytem is not available e.g.

wait for LWB . or press ‘M’ 2x .

If a subsystem is not available, you will see this message (‘LWB’ as an example). If you press MODULE twice times, you will get the System Menu.

OTIS

Software Basic Data


MCS –LCB_II

No.: GAA30082DAC_STM SCN: GAA30082DAC Page: 8/ 65 Date: 2008-11-06

Service Tool Manual

4 Tree S tructure All Service Tool functions are organized as a Tree-Structure. It is divided in a SYSTEM path, where you have access to the main Service Tool functions  STATUS (system monitoring)  TEST (system test functions)  SETUP (setup of system environment) and in a TOOL path. The TOOLS path contains the Service Tool functions which supports installation and maintenance of the elevator. .M. Main Menu

1.

2.

.F. System Menu

Tools

1.

2.

.S. Status Menu

3.

Test Menu

Setup Menu

1

Calls

(13)

1

Events

(23)

1

Install

(36)

1

Search IO

(57)

2

Inputs

(15)

2

Diagnosis

(25)

2

RSL

(37)

2

Erase IO

(58)

3

Outputs

(16)

3

Part

(27)

3

Allowed

(39)

3

Setup Inst

(59)

4

Group

(17)

4

RSL

(28)

1 Enable

(41)

4

Setup Door (*) (60)

5

ICSS

(18)

5

Selftest

(31)

2 Cut Call

(42)

5

Show Hist (*)

6

Cmd

(19)

6

Plug (*)

(33)

3 Card-Rd

(43)

6

CheckConfig(*) (62)

7

Drive (*) (21)

4 SHO/WCO (*) (44)

6

SB Program (*) (63) SB Test (*)

(64)

Opr.Memory

(65)

4

Pos

(45)

7

Legend:

5

DCS

(46)

8

1

Service Tool Key

6

ELD

(49)

9

(9)

page number in this document

7

Speech (*)

(55)

Notes (*): M117 M126 M1334 M137

Drive Plug SHO/WCO Speech

TCBC, GECB only HCB, TCB only not in LCB2 earlier than CAA LCB2 only

M25 M24 M26 M26 M27

Show Hist Setup Door CheckConfig SB Program SB Test

TCB only LCB2, HCB, TCB only LCB2, HCB, TCB only LCB2 only LCB2 only

(61)

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 9/ 65 Date: 2008-11-06

4.1 K ey Overview The Menu System allows you to access the single Service Tool functions if you choose the right path through the Tree Structure by pressing the corresponding key (number 1,2,...8). If there is only one number to choose, you can call the function also with the key ENTER . The ">" character indicates that you can toggle between the different menus using the GOON or GOBACK . The CLEAR key lets you jump one step back. If you want to jump back to one of the three Main Level of the architecture (MONITOR, FUNCTION or SET) you can press the Main Level keys M , F or S .

4.2 S hort K eys The Short Keys provide direct access to certain , often used Service Tool functions, eliminating the need to step through the menu structure. The Service Tool functions Input, Calls, Install, RSL and Events are assigned to the Standard Short Keys S4 (Shift 4), S5 (Shift 5), S6 (Shift 6), S7 (Shift 7), S8 (Shift 8). Short Key S9 (Shift 9) is a free programmable key to store any position of the Tree – Structure as a sixth Short Key. Once you have stored S9 (by pressing S9 at the desired position) you can reset it only on level M (Main – Menu).

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 10/ 65 Date: 2008-11-06

Key

old key name

new key name

Description

S4

SETUP INST

DISP IN

M-1-3-1 SETUP INSTALL

S5

SETUP ALTER

SEL OUT

M-1-3-2 SETUP RSL

S6

RET

.

M-1-2-1 TEST EVENTS

S7

DISPL INPUT

DISP STATE

M-1-1-2 STATUS INPUTS

S8

ENTER CALL

ENT CALL

S9

PROG

TEST

M-1-1-1 STATUS CALLS Programmable Shortkey Select any Service Tool Function and press S9 to store this key as a Shortkey for that function. While using any other Service Tool Function, press S9 to jump to the previously stored function. Press M – S9 to reset the definition for this key. You can now redefine this key for a different Shortkey

.

•

•

•

Example press keys

description

M - 1 -1 - 3

S7

use M113 to view system outputs Program S9 as Shortkey for M-1-1-3 View system inputs Enter calls Use S9 to view system outputs View system inputs

M – S9

Reset S9

M - 1 -1 - 6

Use M116 to view commands Program S9 as Shortkey for M-1-1-6 Enter calls Use S9 to View commands

S9 S7 S8 S9

S9 S8 S9

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 11/ 65 Date: 2008-11-06

5 Menu Functions of the S ervi ce Tool The following chapters describe the functions of the Service Tool. Differences between LCB2, HCB, TCB , TCBC and GECB are clearly marked.

5.1 S tatus Functions The Status Functions allow to monitor the status of the system. The first row provides general information about the Operational Mode and Drive State. The second row is different for each Status Function.

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 12/ 65 Date: 2008-11-06

5.1.1 S tatus Dis play

M-1-1-…

The first row of the Service Tool display is identical for all Status Functions: Display

123

4

5

6 7

description

values

1

A

Car ID

A-D

2

-

moving direction

3

01

floor position

4

IDL

Operational Mode

5

ST

Drive State

6

][

front door state

7

][

rear door state

A-01 IDL ST ][][

8 A-01 >TCI-Lock!.

8

blink message

car identifier for group configurations. Depends on parameter GRP-NO. not moving u moving up d moving down ** unknown position 00-31 current floor number see Reference List for all available Operational Modes see Reference List for all available Drive States ][ fully closed <> opening [] fully opened >< closing DDO both doors are fully closed and Disable Door Operation is activated A blinking message appears if the system is blocked. This message shows the reason of the shutdown. See Reference List for all available Blink Messages.

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.1.2 S tatus C alls Menu

Page: 13/ 65 Date: 2008-11-06

S8 / M - 1 - 1 - 1

With this function you can view the general status of the system and enter calls. A-01 IDL ST ][][ C> U00D00 A 1C

The following keys can be used in this menu: GOON / GOBACK

change the call type

0 … 9

enter a floor number

ENTER

enter the selected call type at the selected floor

Description of display:

OTIS

Software Basic Data


MCS –LCB_II

SCN: GAA30082DAC

1

C

A-01 IDL ST ][][ C> U00D00 A 1C

3

4

Page: 14/ 65 Date: 2008-11-06

Service Tool Manual

Display

1 2

No.: GAA30082DAC_STM

description

values

call type

C U D E

5 6

car call up hall call down hall call emergency hall call

GECB

c u d e

extended car call extended up hall call extended down hall call extended emergency hall call

GECB

2

destination

use GOON / GOBACK to change between the call types 0-31 the value you entered GECB

> K

prompt to enter a destination destination entry device installed at this floor, no call possible

GECB

3

U00

4

D00

5

A

6

1C

number of accepted calls in up direction number of accepted calls in down direction load status

group size and power supply

A ANS (LW X; <100kg) D Default (normal; 80-110%) F Full (LNS; >80%) O overload (LWO; >110%) 1C-5C number of detected cars in the group during Normal Operation 1E-5E number of detected cars in the group during Emergency Power (EPO).

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 15/ 65 Date: 2008-11-06

5.1.3 S tatus Inputs Menu

S7 / M - 1 - 1 - 2

This function displays system inputs. A-01 IDL ST ][][ aes es DW DFC

The inputs are arranged in pages, each page containing four inputs. Active inputs are displayed in upper case letters, inactive inputs are displayed in lower case letters. See document GAAnnnnnXYZ_REF for a list of available inputs. Only those inputs are displayed which are currently used by the software, that means that the list of inputs is rearranged every time an installation parameter is changed. The complete list is shown if the parameter DISP-ALL=1 is programmed. The following keys can be used in this menu: GOON / GOBACK

display the next/previous page of inputs.

UP / DOWN

display a brief description of the input page in the first row.

ON

jump to the first page of inputs

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 16/ 65 Date: 2008-11-06

5.1.4 S tatus Outputs Menu

M-1-1-3

This function displays system outputs. A-01 IDL ST ][][ u D T g .

The outputs are arranged in pages, each page containing four outputs. Active outputs are displayed in upper case letters, inactive outputs are displayed in lower case letters. See document GAAnnnnnXYZ_REF for a list of available outputs. TCBC / GECB

Only those outputs are displayed which are currently used by the software, that means that the list of outputs is rearranged every time an installation parameter is changed. The complete list is shown if the parameter DISP-ALL=1 is programmed. TCBC / GECB

The following keys can be used in this menu: LCB2 / TCB until BAB / HCB GOON / GOBACK

display the next/previous page of outputs.

UP / DOWN

display the selected drive type in the first row of the display.

LCB2 / TCB until BAB / HCB

TCBC / TCB since CAA / GECB GOON / GOBACK

display the next/previous page of outputs.

UP / DOWN

display a brief description of the output page in the first row.

ON

jump to the first page of outputs

TCBC / TCB since CAA / GECB

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 17/ 65 Date: 2008-11-06

5.1.5 S tatus G roup Menu

M-1-1-4

This function displays the status of all cars in the group. A-01 IDL ST ][][ B-03 NOR ST <>][

The first line always displays the status of the own car, while the second line displays the status of one of the other cars in the same group. If no group communication is active (i.e. not installed or broken link), then the following display is shown: A-01 IDL ST ][][ B***************

The following keys can be used in this menu: select the car in the second line of the display

GOON / GOBACK

TCBC / GECB

In the TCBC and GECB software, the group status display can look like this: Display

description

1

nav

2

na

A-01 IDL ST ][][ B-** nav na ][][

1

2

TCBC / GECB

Operational Mode of other car

values

RNG-ICD=0: Some OpModes cannot be transmitted by Ring ICS 3.3 or earlier. Those modes are displayed as "nav": DAR, DCS, UFS, ACC, EAR, DLM Drive State of other car RNG-ICD=3: Only three drive states are available in Ring ICD 4.0 or later: na: not available av: available dc: decelerating

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.1.6 S tatus IC S S Menu

Page: 18/ 65 Date: 2008-11-06

M-1-1-5

LCB2 / TCB / TCBC

This function displays whether ICSS controllers (for EMS) are detected in the group. ICSS IS ONLINE ICSS2 IS OFFLINE

No keys can be used in this menu. LCB2 / TCB / TCBC GECB

This function displays which other boards are detected in the group. The following keys can be used in this menu: select the next/previous information page

GOON / GOBACK

Description of display: Display

1

1

ICSS0 IS ONLINE. ICSS1 is offline

GCB1 GCB2

2

2

1

1

IS ONLINE. is offline

2

2

1

1

Compass is off .

.

GECB

description

values

Tells whether the ICSS0 for EMS (Ring address 11) is alive. Tells whether the ICSS1 (Ring address 10) is alive.

IS ONLINE is offline

Tells whether the GCB1 for Compass (Ring address 12) is alive. Tells whether the GCB2 for Compass (Ring address 14) is alive. Tells whether any GCB has detected keypads and/or touchscreens for Destination Entry.



IS ONLINE is offline COMPASS IS ON Compass is off

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 19/ 65 Date: 2008-11-06

5.1.7 S tatus C ommand Menu

M-1-1-6

This function shows the Door- and Motion-Commands which are generated by the Operational Control part of the Software. A-01 IDL ST ][][ F:CLD6 R:CLD6

The following keys can be used in this menu: select the next page of commands

GOON / GOBACK


A-01 IDL ST ][][ F:CLD6 R:CLD1

1

description

values

1 2

F:CLD6 R:CLD1

front door command from OCSS rear door command from OCSS

see table below see table below

1

MC:CarGoTo

see table below

2

To:01

Motion command from OCSS to MCSS Actual Target

2

A-01 IDL ST ][][ MC:CarGoTo To:01

1

2

Bottom - Top

If a DO-5 or AT120 is installed the following additional displays are available: A-01 IDL ST ][][ F:CLD6 / Cld&Dob

1

1 2

F:CLD6 /Cld&Dob

front door command from OCSS see table below front door command as sent to the see table below DCSS5/AT120

1 2

F:CLD1 /Cld

rear door command from OCSS rear door command as sent to the DCSS5/AT120

see table below see table below

1 2

F: 010 R: 011

status of ST1, ST2, ST3 status of RST1, RST2, RST3

000 - 111 000 - 111

2

A-01 IDL ST ][][ R:CLD1 / Cld .

1

2

A-01 IDL ST ][][ F: 010 R: 011 .

1

2

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 20/ 65 Date: 2008-11-06

Description of the commands: Type Door Commands

DO-5 Commands

Motion Commands

Display

Description

OPEN DEEN CLD1 CLD2 CLD3 CLD4 CLD5 CLD6 CLD7 CLD8 CLD9

open door deenergize door (TCI, DTO, DTC, ESB) close door; no DOB, no LRD, no EDP close door; full DOB, full LRD, full EDP close door; full DOB, full LRD, lim EDP close door; full DOB, lim LRD, lim EDP close door; full DOB, no LRD, no EDP close door; full DOB, no LRD, lim EDP close door; lim DOB, no LRD, lim EDP close door; lim DOB, no LRD, no EDP close door; full SGS, nothing else

Ded&Eds Ded Cld&Dob Cld Ndg Cld&Rev Opn

deenergize door; no door movement allowed stop door; door may be operated using Service Tool (connected to DO-5) close door; only DOB enabled close door; no Reversals enabled close door; no Reversals enabled; reduced profile close door; LRD, DOB and PP enabled open door

CarGoTo ESMGoTo Stand By ReInit ImmStop Nxt Flor

Go to specific floor Emergency Service Standby or Inspection reinit position Immediate Stop Go to next reachable floor

Abbreviations: DOB = Door Open Button LRD = Light Ray Device PP = Passenger Protection

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.1.8 S tatus Drive Menu (TC B C , G E C B only)

Page: 21/ 65 Date: 2008-11-06

M-1-1-7

TCBC / GECB

Displays the status and commands of the drive subsystem. A-01 IDL ST ][][ Drv: AtTarget .

The following keys can be used in this menu: select the next/previous page

GOON / GOBACK


description

values

1

Running

Drive Status

see table below

1 2

GoToLnd 05

Drive Command specified Target

GoToLnd Run to specified landing Top…Bottom

1

Tci

Drive Command

Corr

2

up

specified direction

1

at05

Actual Target (final destination) Motion Target (Accepted Target from Drive) Next Commitable Floor Actual Floor

Au01 NOR FR ][][ Drv: Running .

1

Au01 NOR FR ][][ Cmd: GoToLnd 05.

1

2

or Au01 INS IN ][][ Cmd: Tci up .

1

2

Au01 NOR FR ][][ at05mt05nc02af01

1

2

3

TCBC / GECB

4

2 mt05 3

nc02

4

af01

Correction Run into specified direction Resc Rescue Run to next floor into specified direction Tci Inspection Run (TCI) into specified direction Ero Inspection Run (ERO) into specified direction up move up down move down stop don't move Top…Bottom Top…Bottom Top…Bottom Top…Bottom

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 22/ 65 Date: 2008-11-06

TCBC / GECB

Description of the Drive Status: Drive Status

Description

NotAvail Shutdown Init Idle Running Stopping AtTarget Calibr Wt_F_Saf

Drive is not communicating Drive has shut down Drive is initializing during PowerUp Idle Accelerating or running at constant speed Decelerating to Target Arrived at target Encoder-Adjustment or Learn-Run Wait For Safety; safety chain is open

TCBC / GECB

5.2 Tes t Func tions These functions provides access to the diagnostic functions of the system and allow to test some basic functionalities.

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.2.1 Tes t E vents Menu

Page: 23/ 65 Date: 2008-11-06

S6 / M - 1 - 2 - 1

View all events which has been stored since last cleared . number of runs since the events were last cleared number of elapsed minutes since the events were last cleared

00021 savedRuns 000153 savedMins TCBC since GAA30781AAE:

DOWN time since clear d999:23:59:59.9s

free running 100 msec timer, re-initialized to d000:00:00:00.0s whenever the events are cleared; the timer value to the left is interpreted as 999 days, 23 hours, 59 minutes, 59.9 seconds; when the timer reaches d999:23:59:59.9s it changes format to d4899:23:59:59s and latches at d4900:00:00:00s

View Events The following keys can be used in this menu: GOON / GOBACK

display the next/previous event

UP

clear events

DOWN

display 100 msec timestamps


1 0204 TCI/ERO on. c003 t000020 p**

2

3

4

DOWN TCBC

description

values

1 0204 TCI/ERO on

number and text of event

2 003

counter

see Service Tool Reference List for a list of possible events 0 – 999

3 00020

elapsed time since last occurence of this event car position where the last event occurred

4 **

0204 TCI/ERO on. d034:15:50:24.6s

5

5 d034:15:50:24.6s

timestamp of event occurrence. Interpreted as 34 days, 15 hours, 50 minutes, 24.6 seconds.

0 – 999999 00 – 31 **

unkown position d000:00:00:00.0s through d4900:00:00:00s

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

E ras e Events

Page: 24/ 65 Date: 2008-11-06

You can either erase all events which are stored in the system or erase a single event. The following keys can be used in this menu: GOON / GOBACK

Display the next/previous event Erase all events

UP

Erase EVENTS n=0 y=1 >

? .

Press 1 - ENTER to continue or press CLEAR to cancel Erase EVENTS n=0 y=2 >

? .

Press 2 - ENTER to erase all events or press CLEAR to cancel Erase EVENTS done!

? .

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 25/ 65 Date: 2008-11-06

5.2.2 Tes t Diagnos tics Menu

M-1-2-2

This menu displays the diagnostic values which have been stored in the E2Prom. These values are memorized even if the power is switched off. 01 DIAG ACT-T 000:00:00:01

. .

View Diag nos tics The following keys can be used in this menu: GOON / GOBACK

display the next/previous diagnostic value

UP

display description lower line (available for time-related values only)


1 01 DIAG ACT-T 002:03:04:05

2

1

3

4

5

description

values

1 01 DIAG ACT-T

number and text of diagnostic value

2 002

months

see Service Tool Reference List for a list of existing diagnostic values 0-999

3 4 5 1

days hours minutes number and text of diagnostic value

. .

03 04 05 03 DIAG UP-CNT

01 DIAG UP-CNT . 000000023 .

2

2 000000023

counter

0-29 0-23 00-59 see Service Tool Reference List for a list of existing diagnostic values

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

E ras e Diag nos tics

Page: 26/ 65 Date: 2008-11-06

You can either erase all values which are stored in the system or erase a single value. The following keys can be used in this menu: GOON / GOBACK

Display the next/previous diagnostic value Erase all Diagnostic values

UP

Erase DIAGN. n=0 y=1 >

? .

Press 1 - ENTER to continue or press CLEAR to cancel Erase DIAGN. n=0 y=2 >

? .

Press 2 - ENTER to erase all events or press CLEAR to cancel Erase DIAGN. done!

? .

Erase the displayed diagnostic value ON

Erase Value ? . 02 DIAG TOT-T .

Press ENTER to erase this event or press OFF to cancel

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 27/ 65 Date: 2008-11-06

5.2.3 Tes t Part-No Menu

M-1-2-3

Displays the Software Configuration Numbers (SCN) of the software. No. GAA30081AAA . 28-Aug-01 11:32

The following keys can be used in this menu: display the next/previous number

GOON / GOBACK

Part Numbers of Standard S oftware Display

description

1

No. GAA30081AAA . 28-Aug-01 11:32

2

1 EE=47AG2375

.

1 GAA30081AAA

SCN of Standard-Software

2 28-Aug-01 11:32

date and time of authorisation

1 47AG2375

values

Unit-Number

.

1

PR=G1231032AAA . 28-Sep-04 11:32

2

1 G1231032AAA

SCN of Loader (integrated into FLASH)

2 28-Sep-04 11:32

date and time of Loader

Part Numbers of C ontract S oftware 1

No. U47CE2375 . 28-Aug-01 11:32

1 47CE2375

SCN of Contract-Software

2 28-Aug-01 11:32

date and time of authorisation

Baseline used: . No. GAA30081AAA.

1 GAA30081AAA

SCN of parent software

1

1 47CE2375

Unit-Number

2

1

EE=47CE2375

. .

only TCBC software 30781 only TCBC software 30781

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 28/ 65 Date: 2008-11-06

5.2.4 Tes t R S L Menu

M-1-2-4

LCB2 / TCB / HCB / TCBC

Test the functionality of Remote Stations by address. .

ADR>

.

The following keys can be used in this menu: 0 … 9

enter an RS address

ENTER

confirm the entered address

GOON / GOBACK

test the next/previous RS address

UP / DOWN

test the next/previous bit

ON / OFF

switch the displayed output on or off


1 ADR>04 IN:on

3

2

BIT=1 . OUT:off.

4

1 04 2 1 3 on 4 off

description

values

selected RS address

04 .. 63

selected Bit of that address

1 .. 4

status of RS input status of RS output

on, off on, off

use ON / OFF to change the output

Note that the elevator software cannot update the RSL I/Os as long as long as this menu is selected! For security reasons, some I/Os (e.g. DO-5 outputs ST1-ST3) cannot be changed by this menu. LCB2 / TCB / HCB / TCBC

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 29/ 65 Date: 2008-11-06

GECB

If 3 links are activated (i.e. RSL-TYP=1 and all three links are supported by the board), the following menu appears to chose the RSL link. RSLtst – Menu > 1 = Car Link . RSLtst – Menu > 2 = Hall Link . RSLtst – Menu > 3 = Group Link.


select the link

ENTER

select the link which is currently displayed

GOON / GOBACK

select the next/previous link

The next screen allows to test the functionality of Remote Stations by address. C-ADR>

. .


enter an RS address

ENTER

confirm the entered address

GOON / GOBACK

test the next/previous RS address

UP / DOWN

test the next/previous bit

ON / OFF

switch the displayed output on or off

GECB

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 30/ 65 Date: 2008-11-06

GECB


1

2

3

C-ADR>04 BIT=1 . IN:on OUT:off.

4

5

description

values

1 C

selected RS link

2 04

selected RS address

C=Car H=Hall G=Group 04 .. 63

3

selected Bit of that address

1 .. 4

status of RS input status of RS output

on, off on, off

1 4 on 5 off

use ON / OFF to change the output

Note that the elevator software cannot update the RSL I/Os as long as long as this menu is selected! For security reasons, some I/Os (e.g. DO-5 outputs ST1-ST3) cannot be changed by this menu. GECB

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.2.5 Tes t S elftest Menu

Page: 31/ 65 Date: 2008-11-06

M-1-2-5

Performs a selftest of the software. LCB2 / HCB / TCB / TCBC PR ?

PR: EE: RA: RS:

EE ? RS ?

RA ? .

verifies whether the checksum of the PROM (Flash or Eprom) is correct checks whether the content of the E2Prom has been changed since the last selftest checks whether the RAM can be written correctly checks whether the remote station address setup is correct

LCB2 / HCB / TCB / TCBC GECB PRx SWx EE? RAx . RS? .

PR:

verifies whether the checksum of the secondary loader is correct (is automatically skipped in software version GAA30780AAA) SW: verifies whether the checksum of the application software is correct (is automatically skipped in software version GAA30780AAA) EE: checks whether the content of the E2Prom has been changed since the last selftest RA: checks whether the RAM can be written correctly (is automatically skipped in software version GAA30780AAA) RS: checks whether the remote station address setup is correct GECB

A blinking '?' indicates that the corresponding test is running. After completion of the t est, the display shows '+' or '-', respectively, or 'x' if the test is skipped. The following keys can be used in this menu: LCB2 / HCB / TCB GOON / GOBACK

•

display the next/previous RS-error status

LCB2 / HCB / TCB TCBC / GECB GOON / GOBACK

• •

TCBC / GECB

cancel the actually running test and start the next test display the next/previous RS-error status

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 32/ 65 Date: 2008-11-06


1 PR x

description

2

3

1 PR x

EE - RA + RS05Ar000.

4 5 6

2 EE -

3 RA +

4 RS05 5 Ar

6 000

EPROM test

values ? the test has not yet been completed + the checksum of the EPROM is cor-

rect - the EPROM is corrupted  replace the EPROM! x the test has been skipped (TCBC, GECB only) E2Prom test ? the test has not yet been completed + the content of the E2Prom (parameters, I/Os, diagnostic values) has not been changed since the last selftest - Any value in the E2Prom has been changed since last selftest  Do this test once again. If you don't get a '+' now, replace the E2Prom. x the test has been skipped (TCBC, GECB only) RAM test ? the test has not yet been completed + the RAM is ok - the RAM is corrupted replace board x the test has been skipped (TCBC, GECB only) RS test 04-63 This RS has a problem as described below Remote Station is Ar Available in Setup, but physically not A – Available responding a – not available  check address configuration of RS R –Responding  check wiring and connection r – not responding  replace RS aR Not available in Setup, but physically responding  check I/O-setup  find misconfigured RS AR Available in Setup, and also responding; Parity Error detected  There are multiple RS with the same address in the system Parity Error Counter 000-999

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 33/ 65 Date: 2008-11-06

5.2.6 Tes t Plug Menu

M-1-2-6

LCB2

This menu is used for the factory test. It displays the status of some selected inputs. P1:01001101000-. P7:-00100111xxx.


display the next/previous page of inputs

•


1

2 P1:01001101000-. P7:-00100111xxx.

34

12

5

34

DCL=10 LS=10 DOL=00 TCI=0

56

LCB2

7

. .

description

values

0: 1:

low high

0: 1:

low high

0: 1:

low high

1

01001101000

input status of plug P1:1 – P1:11

2

-

3

-

4

00100111

P1:12 is no input and will not be displayed P7:1 is no input and will not be displayed input status of plug P7:2 – P7:9

5

xxx

P7:10 – P7:12 do not exist

1 2 3 4 5 6 7

1 0 1 0 0 0 0

DCL input status RDCL input status 1LS input status 2LS input status DOL input status RDOL input status TCI input status

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 34/ 65 Date: 2008-11-06

TCB / HCB / TCBC

This menu is used for the factory test and is not usefull for the field. It displays the status of all internal PIO port inputs. 1: B6B7C7....C0 0000001100001111


•

display the next/previous page of inputs

Description of display: The first line describes which inputs are displayed in the second line. Display

1 1: B6B7C7....C0 0000001100001111

description

values

1 2 3

1: 11 00001111

inputs of PIO1 inputs of PIO1-B6 and PIO1-B7 inputs of PIO1-C7 to PIO3-C0

0: 1:

low high

1 2

3: 1111

0: 1:

low high

3

00001111

inputs of PIO3 inputs of PIO3-C7 to PIO3-C4 inputs of PIO1-A7 to PIO3-A0

1

3:

2

1111

inputs of PIO3 inputs of PIO3-C3 to PIO3-C0

0: 1:

low high

3

00001111

inputs of PIO3-B7 to PIO3-B0

1

4:

inputs of PIO4

0: 1:

low high

2

00001111

inputs of PIO4-A7 to PIO4-A0

2233333333

1 3: C7..4A7....A0 0000111100001111

222233333333

1 3: C3..0B7....B0 0000111100001111

222233333333

1 4 A7....A0 0000000000001111

22222222

Note: On TCBC, the ports PIO3-C and PIO4 do not exist. '00000000' will be displayed for these ports. TCB / HCB / TCBC

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 35/ 65 Date: 2008-11-06

5.3 S etup Functions These functions allow to adapt the system to the needs of the jobsite. All values which are changed by these functions are stored into E2Prom. The E2P-Selftest (M1-2-5) will display '-' if any value has been changed since the last selftest.

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.3.1 S etup Ins tall Menu

S4 / M - 1 - 3 - 1

View and setup Installation Parameters. The parameters can only be changed if the car is not moving. INSTALL – Menu > 01 System .


0 … 9

go to the next/previous group of parameters

• •

ENTER

• •

directly access a group of parameters enter a new value for the displayed parameter access the displayed group of parameters store the new value for the displayed parameter (if the car is not moving)


description

1 01 INSTALL – Menu > 01 System ..

1 2

1

1 000

2

000 System new TOP =010> .

3

2 System

4

000 System new TOP =010>009

5

2 System 3 TOP 4 010 5

number of parametergroup name of parameter-group number of parameter within this group name of parameter-group name of parameter value of parameter the value you entered

values see Service Tool Reference List for

a list and description of available parameters

0-255

press ENTER to store this value

Note: A new DCS run is required if TOP or BOTTOM is changed.

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.3.2 S etup R S L Menu

S5 / M - 1 - 3 - 2

LCB2 / HCB / TCB / TCBC

View and setup RSL addresses. The addresses can only be changed if the car is not moving. IO

I AD P AD P .

>


go to the next/previous I/O number

0 … 9

enter an I/O number

ENTER

display the address of the requested I/O number

UP / DOWN

go to the next/previous I/O number which is different from "0 00-0"

ON

change the Invert-Bit of the I/O number:
- ON – ENTER Note that you have to enter the address again if you want to change the InvertBit.


IO I AD P AD P 0001=0 04 1> .

1

2 3

4

IO I AD P AD P 0001=0 04 1>05 3

5

6

description

values

1 0001 2 0

I/O number invert-bit

0…9999 0,1

3 04

address of the Remote Station bit of the Remote Station the address you entered the bit you entered if the Invert-Bit is set, the first row will blink

4-63

4 1 5 05 6 3

1

1 Inverted IO

Inverted IO ! . 0691=1 16 3> .

LCB2 / HCB / TCB / TCBC GECB

1-4 4-63 1-4

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

View and setup RSL addresses. The addresses can only be changed if the car is not moving. C-IO I AD P AD P > .


go to the next/previous I/O number

0 … 9

enter an I/O number

ENTER

display the address of the requested I/O number

UP / DOWN

go to the next/previous I/O number which is different from "0 00-0"

ON

change the Invert-Bit of the I/O number:
- ON – ENTER Note that you have to enter the address again if you want to change the InvertBit.


1

description

values

1 C

link for the displayed I/O number

2 0001

I/O number

C = Car link H = Hall link G = Group link 0…9999

3 0

invert-bit

0,1

4 04

address of the Remote Station bit of the Remote Station the address you entered the bit you entered if the Invert-Bit is set, the first row will blink

4-63

C-IO I AD P AD P 0001=0 04 1> .

2

3 4

5

IO I AD P AD P 0001=0 04 1>05 3

6

7

5 1 6 05 7 3 1 Inverted IO ! . 0691=1 16 3> .

GECB

1 Inverted IO

1-4 4-63 1-4

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.3.3 S etup A llowed Mask Menu

Page: 39/ 65 Date: 2008-11-06

M-1-3-3

This function is used to setup the Floor Table masks. Four different Allowed Masks are available: ALLOWED – Menu > 01 Enable . ALLOWED – Menu > 02 Cut_Call . ALLOWED – Menu > 03 Card_Rd. . ALLOWED – Menu > 04 SHO/WCO .


change to the next/previous mask

1 … 4

press a number to select the mask directly

ENTER

select the displayed mask

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 40/ 65 Date: 2008-11-06

K ey Handling for all Allowed Mas ks The following keys can be used in all Allowed Masks: GOON / GOBACK

change to the next/previous floor number

0 … 2

enter numbers to program the Allowed Mask

ENTER

store the Allowed Mask

CLEAR

Delete the last input

The following keys can be used in the 1 st Allowed Mask: LCB2 / TCB / HCB display the corresponding Opening number in the first row: UP / DOWN

at F:00 R:01 P R 00 1100 1100 0 0

LCB2 / TCB / HCB GECB UP / DOWN

Display the corresponding Opening number in the first row: Switch between standard and extended calls: standard calls:

at CUDE CUDE P R 00 1100 1100 0 0

opening number:

at F:00 R:01 P R 00 1100 1100 0 0

extended calls:

at cude cude P R 00 1100 1100 0 0

opening number:

at f:00 r:01 P R 00 1100 1100 0 0

GECB

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.3.3.1 E nable Mask

M-1-3-3-1

The following functions can be set for each floor: which type of call is allowed allow or prohibit parking define Short Landings • • •

ALLOWED – Menu > 01 Enable .


at CUDE CUDE P R 00>1110 0000 0 0

1

2

3

1 2

at CUDE

4 5

C U D E

description

values

floor number front Standard Enable Mask Standard Car Call Standard Up Hall Call Standard Down Hall Call Standard Emergency Hall Call

00 - 15 0000 … 1111 see below 2000 dummy opening 0 call type not allowed in this Opening 1 call type allowed in this Opening

GECB

lower case letters indicate the call mask for Extended Calls

1

2

at F:00 R:-- P R 00>1110 0000 0 0

3

3 4

GECB CUDE P

rear Enable Mask Park Enable Bit

5

R

Reduced Run

1

F:00

2

R:--

Opening Number for front door Opening Number for rear

3

at00

floor level

0 parking allowed here 1 no parking allowed here Distance between displayed floor and the floor above: 0 Normal Run 1 Short Run (not for OVF10) 4 Medium Run (not for OVF10) Note: Not necessary for TCBC Note: Removed for GECB 00-31 00-31 00-15

TCBC / GECB

For TCBC the R-Bit is not necessary. The handling of Short Landings is completely done by the Drive. TCBC / GECB LCB2, TCB

Drivetypes with learnrun (OVF20, OVFWW) require the setting of R=1 only in 1LS and 2LS. LCB2, TCB

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.3.3.2 C ut Call Mask

Page: 42/ 65 Date: 2008-11-06

M-1-3-3-2

The following functions can be set for each floor: which type of call is affected by Cut Call key switches park with opened doors • • •

ALLOWED – Menu > 02 Cut_Call .


1

2

3

4

at CUDE CUDE Op . 00>1110 0000 0 .

1 2

3 4

at CUDE C U D E CUDE Op

description

values

floor number front Enable Mask Car Call Up Hall Call Down Hall Call Emergency Hall Call rear Enable Mask Park with open doors

00 - 15 0000 … 1111 see below 0 calls are always allowed 1 calls are deleted if any CCO keyswitch is active 0000 … 1111 see above 0 park with closed doors 1 park with front door open 2 park with rear door open 3 park with both doors open

The following RSL inputs can be used to disable calls: I/O Name Remark 610 CCOC Cut Car Calls On Car link 611 CCOH Cut Car Calls On Hall link 612 HCCO Hall Call Cut Off 613 GCCO Group Call Cut Off 746 HCOC Hall Call Cut Off from Car To prevent malfunction: All unused I/O’s from the table above must be set to ‘010’ (default).

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.3.3.3 C ard R eader Mas k

Page: 43/ 65 Date: 2008-11-06

M-1-3-3-3

LCB2

The description for this mask is only valid for LCB2 software versions since GAA30082CAA LCB2 TCB / HCB / TCBC / GECB

The description for this mask is valid for all software versions TCB / HCB / TCBC / GECB

The following functions can be set for each floor: which type of call is affected by Card Reader Operation activate Special Door Open Button (SDOB) • •

ALLOWED – Menu > 03 Card_Rd. .


1

2

description

3

4

at CLD- CLD- Sb . 00>1110 0000 0 .

1 2

at CLD-

floor number front Enable Mask C Car call L

force to Lobby

D

enable DOB

-

3 4

CLDSb

not used rear Enable Mask Special Door Open Button

values

00 - 15 0000 … 1110 see below 0 car call is only allowed if card reader input is activated 1 car call always allowed 0 don't force car to lobby 1 force car to Lobby if DOB is pressed while the car is resting with closed doors at this floor 0 DOB disabled 1 DOB enabled; setting of L-bit is ignored 0000 … 1110 see below 0 no SDOB 1 only front SDOB enabled 2 only rear SDOB enabled 3 both SDOB enabled

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.3.3.4 S HO and WC O Mas ks

M-1-3-3-4

LCB2

The description for this mask is only valid for LCB2 software versions since GAA30082CAA LCB2 TCB / HCB / TCBC / GECB

This mask doesn't exist yet. TCB / HCB / TCBC / GECB

This mask is used to setup the Shabat Operation and Wild Car Operation. The following functions can be set for each floor, separately for SHO and WCO: Select at which floor the car will stop Select which door will be opened • •

ALLOWED – Menu > 04 SHO/WCO .


1

2

3

at SUDFR WUDFR . 00 0000 0000 .

1 2

at SUDFR U D F R 3 WUDFR U D F R

description

values

floor number SHO mask stop in Up direction stop in Down direction open Front door open Rear door WCO mask stop in Up direction stop in Down direction open Front door open Rear door

00-15 0 action disabled at this floor 1 action enabled at this floor

0 action disabled at this floor 1 action enabled at this floor

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.3.4 S etup Pos ition Indicator Menu

M-1-3-4

This menu defines the display of the Position Indicator at each floor. Pos.Ind. new at: L 00 =10 > .

The following keys can be used: GOON / GOBACK

change to the next/previous floor number

0 … 9

enter a code number to program the Position Indicator (see list below)

ENTER

store the new code


Pos.Ind. new at: L 00 =10 > .

1

2

3

Pos.Ind. new at: L 00 =10 >01

description

values

1 L 2 00

left or right digit of the PI floor number

L, R 00-31

3 10

code for the displayed character or digit the new code you entered

00-39 (see list below)

4 01

00-39 (see list below)

4

Description of codes: Code Symbol

0 1 2 3 4 5 6 7 8 9

0 1 2 3 4 5 6 7 8 9

Code Symbol

10 11 12 13 14 15 16 17 18 19

(blank) A B (*) C D (*) E F G (*) H I (*)

Code Symbol

20 21 22 23 24 25 26 27 28 29

(*) for 16-segment position indicator and ELD only!

J (*) K (*) L M (*) N (*) O P Q (*) R (*) S

Code Symbol

30 31 32 33 34 35 36 37 38 39

T (*) U V (*) W (*) X (*) Y (*) Z (*) * all segments

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 46/ 65 Date: 2008-11-06

5.3.5 S etup DC S -R un Menu

M-1-3-5

The Door Check Sequence (DCS) - Function is a safety feature for MCS controllers. It insures that all hoistway door contacts are installed correctly and will open the safety chain when a door opens. Until the Door Check Sequence is finished successfully it is only possible to move the car in inspection mode. Normal runs are disabled. to start DCS . press ENTER .

The following error messages can be displayed before the DCS run is started: Error Message

Reason

DCS Start Error: Into 1LS and DZ!

The car is not at the lowest floor.  move the car to the lowest floor (ERO)

DCS Start Error: Leave 1LS! .

The car is in 1LS, but not in the doorzone.  Leave 1LS or move into DZ.

DCS Start Error: Not able to Run!

The car is in shutdown.

DCS Start Error: Switch off INS! !

The car is in TCI or ERO mode.  Switch to Normal

DCS Start Error: already done >

The check has already been done  press GOON to start DCS again.

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual


12

3

4 5

-00 DW:clsd <>][ open front door.

6

description

values

1 -

moving direction

2 00

floor position

3 DW:clsd 4 <>

status of DW input and DS contact front door state

5 ][

rear door state

6 open

action

not moving u moving up d moving down ** unknown position 00-31 current floor number DW:clsd landing door is closed dw:opnd landing door is opened ][ fully closed <> opening [] fully opened >< closing ][ fully closed <> opening [] fully opened >< closing open front door open rear door check DW input close front door close rear door moving to bottom up to next floor see table below

front door

error text

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 48/ 65 Date: 2008-11-06

The following error messages can be displayed during the DCS run: Error Message

Reason

Front Door Error Rear Door Error aborted by ENTER DW not closed Door opening Err Position Error Door closing Err SE is missing!

landing door contact is not opened while front car door is opened landing door contact is not opened while rear car door is opened The key ENTER has been pressed; DCS is aborted. car door is closed but landing door contact is open door could not be opened within 20 seconds The calculated position is higher than TOP. door could not be closed within 20 seconds safety chain is closed but SE is low.

At the end of the DCS the following displays appear: Error Message

Reason

DCS successfull . press GOON >

 press

Check PES,GTC... press GOON >

Reminder what has to be done next  press GOON to continue

to start normal ! press GOON >

 press

GOON to continue

GOON to continue

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 49/ 65 Date: 2008-11-06

5.3.6 S etup E LD Menu

M-1-3-6

The ELD – function is used to define the ”Customer Message” of the OTIS 2000-ELD (CPI-11). For each floor the Customer Message can be (Floor-Mode)  displayed (Edit-Mode and Default-Mode)  modified  or stored into EEPROM (Store-Mode). Overview

1

M - 1 -3 - 6

5 CLEAR send Customer Messages to ELD

Floor-Display 2

ENTER

CLEAR

ON

Edit-Display 3

ENTER

CLEAR

Store-Display 4

ENTER

Default-Display CLEAR ENTER OFF

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Floor-Display:

The following keys can be used: GOON / GOBACK

Change the floor number

0 … 9

Enter a floor number

UP / DOWN

Change the Edit-Mode, which will be used in the Edit-Display

ENTER

Transition to the Edit-Display

CLEAR

All messages will be sent to the ELD if you have been been in the Store-Display. Store-Display.

Floor-Display:


0

2

00?FLOOR ALL?ELD BASEMENT .

description

values

1 00

level number

0-31

2 ALL

selected Edit-Mode, which will be used in the Edit-Display

ALL: A-Z: 0-9: %/): SPE: HEX:

3 BASEMENT

Customer Message which is currently stored in the E2Prom for the selected level

3

all characters available only A-Z only 0-9 only &(),-./:<>' only ÄÁÅÇØÖÆ all characters available available by using hex input mov: move the text to the left or right

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Edit-Display:

The following keys can be used: UP / DOWN

Change the cursor position within the customer message. The selected position is marked by a blinking "?".

GOON / GOBACK

Change the Selected character. The range of available characters is defined by the active Edit-Mode. Edit-Mode "mov": Move the displayed displayed Customer Message to the left or right. This is an easy way to center the message on the ELD.

1 … 9

Skip through the character set using the selected step width (Key-No.)

0 … F

Edit-Mode "HEX": Input 2-digit-HEX-code to enter a new character

ON

Transition to the Default-Display, which allows to use predef ined Customer Messages

ENTER

Transition to the Store-Display.

CLEAR

Back to the Floor-Display. The current Customer Message will be buffered so that you can change the Edit-Mode without loosing your changes.

Edit-Display:


1

2

3

00 E? ALL
4

Edit-Mode HEX: 1

2 3

4

00 E?45 HEX
5

description

values

1 00

floor number

00-31

2 E?

selected character

3 ALL

selected Edit-Mode

4 1 2 3

4 HEX

cursor floor number selected character HEX-code for the selected character Edit-Mode "HEX"

5 ?

cursor

? 00 E 45

see above 00-31 00 - FF HEX

OTIS

Software Basic Data


MCS –LCB_II

SCN: GAA30082DAC Page: 52/ 65 Date: 2008-11-06

Service Tool Manual

S tore-D i s play: play:

The following keys can be used: ENTER

Store the displayed Customer Message into E2Prom. Activate Floor Mode

CLEAR

Back to Edit-Mode

S tore-D tore- D i s play play :


1 00 write E2P? BASEMENT

2 1

.

description

values

1 00

level number

00-31

2 BASEMENT

current Customer Message

.

alternating with

00 press ENTER . BASEMENT .

2

No.: GAA30082DAC_STM

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Default-Display:

The following keys can be used: 0 … 9

Two digits input to select the Default Message by entering the List-No.

UP / DOWN

select the language

GOON / GOBACK

select the predefined Default-Message

ENTER

Transition back to Edit-Display. The desired Default Message will be buffered.

CLEAR , OFF

Back to Edit-Display without buffering your changes.

Default-Display:


1

2

3

00 06?ELDdef?ENG GARAGE .

4

1 00 2 06 3 ENG 4 GARAGE

description

values

level number number of selected default message selected language selected Default message

00-31 00-19 ENG, GER, ITA see table below

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

List of Default Messages No.

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

ENG

LOBBY BASEMENT PENTHOUSE FLOOR RECEPTION EXIT GARAGE SECRETARY RESTAURANT CAFETERIA GARAGE POOL SAUNA DOCTOR 0 123 456 789 : . () <> / -, & ’ ABCD EFGH IJKL MNOP QRST UVWXYZ Ä Á Å Ç Ø Ö Æ

GER

ITA

ERDGESCHOSS KELLER DACHTERASSE ETAGE EMPFANG AUSGANG TIEFGARAGE SEKTRETARIAT RESTAURANT KAFFEESTUBE PARKHAUS SCHWIMMHALLE SAUNA ARZT 0 123 456 789 : . () <> / - , & ‘ ABCD EFGH IJKL MNOP QRST UVWXYZ Ä Á Å Ç Ø Ö Æ

TERRANO SOTTERRANEO ATTICO PIANO RICEZIONE USCITA POSTEGGIO SEGRETERIA RISTORANTE CAFFETERIA POSTEGGIO PISCINA SAUNA DOTTORE 0 123 456 789 : . () <> / - , & ‘ ABCD EFGH IJKL MNOP QRST UVWXYZ Ä Á Å Ç Ø Ö Æ

empty string

HEX-CODE Table ASCII

HEX

ASCII

HEX

Blank & ( ) , . / : < >

20 26 28 29 2C 2D 2E 2F 2A 3C 3E

0 1 2 3 4 5 6 7 8 9

30 31 32 33 34 35 36 37 38 39

ASCII

A B C D E F G H I J K L M

HEX

ASCII

HEX

41 42 43 44 45 46 47 48 49 4A 4B 4C 4D

N O P Q R S T U V W X Y Z

4E 4F 50 51 52 53 54 55 56 57 58 59 5A

ASCII

Ä Á Å Ç A-E Ø Ö

HEX

80 81 82 83 84 85 86 87

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.3.7 S etup S peech Menu (L C B 2 only)

M - 1- 3 - 7

LCB2

This menu is used to setup the messages for the vendor speech synthesizer which is controlled by the I/Os 647-656. FLOOR MSG AT 000 01 02 03 04 .

Each message consists of up to four phrases which will be played in sequence. You can view and change the phrases for all available messages. The following keys can be used: GOON / GOBACK

change the message which should be displayed or programmed

0 … 9

change the codes for the phrases

ENTER

store the phrase codes into E2Prom

CLEAR

delete the last input


1

description

1 FLOOR MSG AT 000

Type of message

2 01 27 00 00

codes of 4 phrases for the above message

FLOOR MSG AT 000 01 27 00 00 .

2

LCB2

values

FLOOR MSG AT 000 … FLOOR MSG AT 031 UP DIR MESSAGE DOWN DIR MESSAGE WELCOME MESSAGE NUDGING MESSAGE OVERLOAD MESSAGE EPO MESSAGE INSPECTION MSG ALARM MESSAGE EXIT CAR MESSAGE TEST MESSAGE

see table below. This example would say "First Floor"

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

LCB2

Phrase codes for Speech Synthesizer: dec

hex

text

dec

hex

text

dec

hex

text

00 01 02 33 34 35 36 37 38 39 13 11 12 13 14 15 16 17 18 19 23 21 22

00h 01h 02h 33h 34h 35h 36h 37h 38h 39h 3Ah 3Bh 3Ch 3Dh 3Eh 3Fh 13h 11h 12h 13h 14h 15h 16h

(no operation) First Second Third Fourth Fifth Sixth Seventh Eighth Ninth Tenth Eleventh Twelfth Thirteenth Fourteenth Fifteenth Sixteenth Seventeenth Eighteenth Nineteenth Twenty Thirty Forty

23 24 25 26 27 28 29 33 31 32 33 34 35 36 37 38 39 43 41 42 43 44 45

17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh 23h 21h 22h 23h 24h 25h 26h 27h 28h 29h 2Ah 2Bh 2Ch 2Dh

Fifty Plaza Ground Twentieth Floor Basement Thirtieth Fortieth Fiftieth Story Garage Mezzanine Level Lobby Restaurant Lower Main Cafeteria Parking One Two Three Upper

46 47 48 49 53 51 52 53 54 55 56 57 58 59 63 61 62 63

2Eh 2Fh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h 3Ah 3Bh 3Ch 3Dh 3Eh 3Fh

Going up Going down Please stand clear of the closing door This elevator is full Please take the next elevator Do not be alarmed We are experiencing a temporary power interruption minor technical difficulties is needed for an emergency Please exit when the doors open You are pressing...buttons required To summon assistance Concourse Please push the alarm button Good morning Penthouse

LCB2

5.4 Tools Functions These are a couple of functions for additional diagnostic.

64-126 127

(spare) 7Fh

Test sequence initiator

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.4.1 S earch IO

M-2-1

This functions finds all I/O-Numbers which are programmed to a specific RSL address. The following keys can be used: 0 … 9

enter an RSL address and bit

ENTER

start or continue the Search Run

CLEAR

delete the last input


1 Search-IO ? Adr: 04 / Pin: 1

2

3 1

Search-IO ? >04 1< IO: 0001

2

3

description

values

1 ?

status indicator

? waiting for input (ENTER) ! searching

2 04

Address to be searched for Pin/Bit to be searched for status indicator

3 1 1 ? 2 04 1 3 0001

Search-IO . no more march! .

Search-IO no match!

.

.

Addess and Pin to be searched for I/O-number which is programmed for this Address/Pin no further I/ONumbers have been found no I/O-Number has been found

? waiting for input (ENTER ! searching 04 1 … 63 4 0000 - 9999

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.4.2 E rase IO

M-2-2

This function completely erases the I/O-Setup in the E2PROM. Erase IO_Part. n=0 y=1 / Enter . display

keys

Erase IO_Part. n=0 y=1 / Enter .

1


2

description

0 & ENTER

leave menu; the setup will not be erased

1 & ENTER

first confirmation

0 & ENTER


2 & ENTER

confirm again to erase the I/O-Setup 1: countdown; the procedure is finished when this number reaches zero

Erase IO_Part. Please Wait:1581

3

1

After calling this function all RemoteStation-Adresses will have been deleted and all I/Os will be inactive: I/O-Nr.

name

default

I/O-Nr.

name

default

0 7-9 12 17-19 224-255 480-511 544 588 610-613 624 625 691

DOL LWX, UIS, DIS LWX NU, NUSD, NUG FPD-xx CRS-xx RDOL MTC CCO EFO ESH TCI

0 0 0 0 0 0 0 0 0 1 0 1

692, 693 694 695 697 703 746 772 775 783 784 1000 all others

1LS, 2LS DCL RDCL MCLS ON HCOC AEFO XEFO TCIB PDD CLR

1 0 0 0 0 0 1 0 1 0 0 0

01-0 01-0 01-0 01-0 01-0 01-0 01-0 01-0 01-0 01-0 01-0 01-0

Description of the default value: 0

1

01-0.

2

3

1 2 3

Invert-Bit address bit

01-0 01-0 01-0 01-0 01-0 01-0 01-0 01-0 01-0 01-0 01-0 00-0

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 59/ 65 Date: 2008-11-06

5.4.3 S etup Ins t

M-2-3

This function completely erases the Installation Parameter Setup in the E2PROM. Description of display: Setup Install ? n=0 y=1 / Enter . display 1

2

3

keys



Setup Install ! Please Wait: 016

1

description

0 & ENTER


1 & ENTER

first confirmation

0 & ENTER


2 & ENTER

confirm again to erase the I/O-Setup 1: countdown; the procedure is finished when this number reaches zero

After calling this function all parameters have been set to the Def ault-value as indicated in the document GAAnnnnnXYZ_INS.

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.4.4 S etup Door

Page: 60/ 65 Date: 2008-11-06

M-2-4

LCB2, TCB, HCB

This function allows you to change from predefined Door Operators (DOOR=0-10) to Generic Door Operator (DOOR=11) without programming each parameter separately. Description of display: display 1 Which door type? front > .

2 Which door type? rear > .

3

4

F: FLH R: 9550 TLD

.

.

Loading done!. Have fun! .

keys

description

0 … 9

Enter a doortype as listed in the List of Installation Parameters for parameter DOOR.

ENTER

confirm

0 … 9

Enter a doortype as listed in the List of Installation Parameters for parameter REAR.

ENTER

confirm

ENTER

Store the default values for Generic Door Operator Parameters

Finished

Now you can setup DOOR=11 (or REAR=11) without changing the behaviour of the software. LCB2, TCB, HCB

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 61/ 65 Date: 2008-11-06

5.4.5 S how His tory (TCB only)

M-2-5

TCB

With this menu you can store the commands of the coded interface between TCB and OVF-WW, so that you can view them later. You can start and stop the storage with the Service Tool. Note that the storage will stop automatically when the memory is full. Engineering only. Description of display: display

keys

description

1

press ENTER to. start storage .

ENTER

The storage will begin when you press ENTER.

2

Storage running. ENTER to stop .

ENTER

All commands of the coded interface are stored until the buffer is full or ENTER is pressed again

3

Buffer is full!. ENTER to cont. .

ENTER

Buffer is full. No more commands can be stored. Press ENTER to view the commands which have been stored.

4

5

01: DFC ip DZ . lr DR rn SC lns . or 02: DFC ip DZ . . (WT )

GOON / GOBACK

. * end of data * .

ENTER

TCB

The first line displays the state of some inputs, while the second line displays the status on the coded interface (either from TCB or from MCB) One entry is stored whenever one of the signals is changing. Use GOON/GOBACk to view the next/previous entry. No more entries in the buffer. Press ENTER to start again.

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 62/ 65 Date: 2008-11-06

5.4.6 C heck C onfig LCB2

This menu is not available for LCB2 LCB2 TCB / HCB / TCBC

Introduced for future enhancements. Currently no checks are performed. Config Check: No Error

.

.

TCB / HCB / TCBC GECB

This menu is not available for GECB GECB

M-2-6

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

Page: 63/ 65 Date: 2008-11-06

5.4.7 S mart B utton Prog ram (L C B 2 only)

M-2-6

LCB2

This menu is used to program a single Smart Button. Make sure that the elevator is switched to ERO and a new unprogrammed Smart Button is connected to the RSL. TOOLS - Menu > 6 = SB Program .

Description of display: display

keys

description

1

Select Adr: 00 . .

0 … 9

enter TWO digits to enter the RS-Address

2

Select Adr: 12 . Pin: .

1 … 4

enter the pin number The TTL of the Smart Button starts to blink (ON: 1.5 seconds OFF:0.1 seconds)

3

Select Adr: 12 . Pin: 3 > ENTER .

ENTER

press ENTER to confirm address and pin The TTL of the Smart Button blinks in a different way (ON: 0.8 seconds OFF: 0.8 seconds)

4

Press Button for min 3 Seconds .

press the Smart Button

press the Smart Button for at least 3 seconds to program the address into the Button. If the programming fails, the TTL blinks rapidly (ON: 0.2 seconds OFF: 0.2 seconds) After successful programming the TTL is constantly switched on and the following display is shown.

5

Programming OK . Press >MODULE<.

LCB2

M

leave this menu

OTIS

Software Basic Data


MCS –LCB_II


Service Tool Manual

5.4.8 S mart B utton Tes t (L C B 2 only)

Page: 64/ 65 Date: 2008-11-06

M-2-7

LCB2

With this menu a single unprogrammed Smart Button can be tested. Make sure that the elevator is switched to ERO and a new unprogrammed Smart Button is connected to the RSL. TOOLS - Menu > 7 = SB Test .

The display shows the state of the input and the output of the Button: SB TEST AT ADR 4 IN:off OUT:off.

Different from the normal TTL handling the output is toggled each time the Smart Button is pressed (press to switch TTL on, press again to switch TTL off). The following keys can be used: ON / OFF

LCB2

switch the TTL of the Smart Button on and off

BD Service Tool Manual GAA30082DAC 2009-11-30

Recommend Documents