Matemática Curso de Admissão, Ary Quintela, Companhia Editora Nacional,com 1800 exercícios diversos, questões de concursos antigos. Uma obra hoje, muito rara.Descrição completa
asigurari
Description complète
Full description
Full description
Full description
Full description
njhbikycfhmbvFull description
Bag FiltersFull description
kb
information for bag filterFull description
Descripción: njhbikycfhmbv
Semoga bisa membantuDeskripsi lengkap
Deskripsi lengkap
Full description
Classification:
Reference:
RS05-006
Date:
NTB06-046
June 13, 2006
2005 PATHFINDER, XTERRA, AND FRONTIER; DRIVER’S SEAT SIDE AIR BAG OPEN CIRCUIT (DTC B1134) APPLIED VEHICLES:
An “open circuit” DTC DTC code (SIDE (SIDE MODULE MODULE LH [OPEN] / B1134) is stored in the SRS control unit,
Side Air Bag Connector
and The connector for the driver’s seat side impact air bag module is disconnected (either completely or partially), NOTE: If CONSULT-II shows the above code (B1134), and the driver’s seat side air bag connector is not disconnected, this bulletin does not apply. Return to ASIST for for further diagnostic diagnostic information. information.
Figure 1 (View from under the front of the driver’s seat)
ACTION
Change the location of the driver’s seat side impact air bag connector by installing the kit listed in the Parts Information.
"ACTION" (above) is to give you a quick idea of the work IMPORTANT: The purpose of "ACTION" you will be performing. You MUST closely follow the entire Service Procedure (starting on page 2) as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended intended for use by qualified technicians, not 'do-it-yourselfers'. 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this this applies to your vehicle.
1/4
PARTS INFORMATION DESCRIPTION SAB Connector Service Kit.
PART # 87885-EA01E
QUANTITY 1
CLAIMS INFORMATION Submit a Primary Operation (PO) line claim using the following claims coding: DESCRIPTION Install SAB Connector Service Kit
OP CODE RX35AA
SYM ZE
DIA 62
FRT 0.6 hrs
SERVICE PROCEDURE
1. Write down all radio station presets.
Presets AM FM-1 FM-2
1
2
3
4
5
2. Disconnect both battery cables (negative cable first).
3. Wait at least 3 minutes after the battery cables are disconnected before disconnecting any air bag connectors.
2/4
6
4. From under the front of the driver seat, drill 2 holes in the connector bracket as shown in Figure 2.
The seat does not need to be removed.
Use a
! inch
drill bit.
CAUTION: Make sure to use a rag or other suitable material to catch the metal shavings from the drilled holes. Don’t let the shavings fall into the electrical connectors, carpet, seat track or other components that are under the seat.
20mm
20mm
24mm
Figure 2 5. Install the new connector holder in the holes you just drilled.
A new connector holder is included in the kit listed in the Parts Information.
Position the connector holder as shown in Figure 3 and snap it in place. Connector holder
Figure 3 3/4
6. Unsnap the side air bag connector from its original location and snap it into the new connector holder as shown in Figure 4.
Remove and discard the old connector holder.
Leave the buckle connector in the same location (don’t move it).
Edge Guard
Side Air Bag Connector in New Location
Old Location of Side Air Bag Connector and Connector Holder
Buckle Connector (Don’t Move)
Figure 4
7. Install the edge guard as shown in Figure 4.
Edge Guard is included in the kit listed in the Parts Information.
8. Re-connect the battery cables; positive cable first.
9. Re-set the radio station presets.
10. Using CONSULT-II, erase any DTCs that are stored in the air bag control unit.
