Security Level:
47pt
Configure IP BTS via CME GUI
www.huawei.com
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
1
Right click the MBSC icon. Click ‘GSM BTS TOPOLOGY’.
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 2
2
Select the subrack no. and slot no. of the interface board to which the BTS will connect. For example, it should be an FG2a working in IP mode. Right click the interface board and then click ‘Add Site’. HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 3
3
Fill in the parameters according to the planned data. BTS IP = BTS traffic IP;
BSC IP = BSC IP that connect to this BTS
This project has some naming rules of BTS in the next page. Please obey them. HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 4
4
Rules for add BTS
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 5
5
Double click the new BTS icon
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 6
6
This step is just for the BTS that use APM30 cabinet. Right click SRN 7, SN 0, and then click ‘Add PMU’.
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 7
7
Add boards according to the planned data. This page is showing the APM30 cabinet. For Virtual cabinet, there is only Subrack 0. HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 8
8
Right click ‘TOPO’, click ‘Add RXUCHAIN’
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 9
9
Fill the parameters according to the planned data. This project has some naming rules of RXUCHAIN in the next page. Please obey them. *For more than 1 RXUCHAIN, please repeat these two steps. HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 10
10
Rules of RXUCHAIN
Configure all the BTSRXUCHAIN according to the BTS layout:
RXUCHAIN0: 0-0-6-0 RXUCHAIN0: 0-0-6-1 RXUCHAIN0: 0-0-6-2
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 11
11
Add MRRU in RXUCHAIN
Right click RXUCHAIN on which the MRRU board will be. Click ‘Add’ -> ‘Add MRRU’.
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 12
12
Fill the parameters according to the planned data. Is Configure Check Threadhold = YES Forward Bandwidth = 125 Receive Bandwidth = 250 Power Bandwidth = CLASS0 This project has some naming rules of MRRU in the next 2 page. Please obey them. *For more than 1 MRRU board, please repeat these 2 steps. HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 13
13
Rules of MRRU (1) Add RFU
ADD BTSRXUBRD
Subrack No. = 60 + CPRIPort + (Position - 1)*6 Slot No. = 0 RXU Chain No. = CPRIPort Position = 1 + cascadeNo.
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 14
14
Rules of MRRU (2)
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 15
15
Adjust BTSRXUBP
MRRU/GRRU Second Receive Mode = DOUBLE_ANTENNA Configure ‘Working Standard’ according to the planned area. HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 16
16
Adjust BTS parameters
Right click the BTS icon Click ‘BTS Configuration Express’ HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 17
17
Configure BTS Description
BTS Basic Attrbutes -> BTS -> BTS Description BTS description = BTS name-siteLocation: HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
125GHI-Ghimpati Page 18
18
Configure BTSESN
Configure BTSESN according to the actual data. 1. Click ‘+‘ 2. Fill in the esn 3. Click ‘ ‘
√
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 19
19
Configure BTSIPCLKPARA
Clock Protocol Type = ‘PTP’ Clock Synchronizaton Mode = ‘INTERSYN’ Domain = ‘0’ Configure IP address according to the planned area. HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 20
20
Configure BTSIPRT
‘BTS Transmission Link’ -> ‘IP BTS Route’ Destination IP address is the ip segment of MBSC Port IP Destination address mask is the mask of MBSC Port IP Forward route address is the gateway of BTS traffic IP HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 21
21
Following shows the GCell configuration
Single click the BTS icon Right click on the right panel, click ‘Add Cell’
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 22
22
Fill the parameters according to the planned data
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 23
23
Following shows the Freq configuration
Right click the cell Click ‘Assign Frequency’
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 24
24
Select the frequency Click ‘OK’ HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 25
25
Following shows the TRX configuration
Right click the cell Click ‘Add TRX’ HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 26
26
Select the cell in the Cell List Click ‘Add Binding(s)’ HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 27
27
Fill the ‘Logical TRX No.’ according to the planned data Select TRX Board; select TRX Board Channel For the BCCH Frq, please check the checkBox in front of the ‘Main BCCH’ Click ‘Bind TRX’ to bind frequency to trx channel. HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 28
28
Set ‘Cell Hop Mode’ and ‘HSN’ according to the planned data Click ‘Apply’ If you want to modify the maio, please double click on the little cell like the blue circle. HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 29
29
Following shows the Cell configuration
Right click the cell Click ‘Cell Configuration Express’ HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 30
30
Cell Attributes -> Basic GPRS Attributes of 2G Cell Configure ‘GPRS’, ‘NO’ and ‘Routing Area’ according to the planned data HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 31
31
Following shows the TRX configuration
Right click the trx Click ‘TRX Configuration Express’ HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 32
32
Configure GTRXDEV
Power Type = 20W --Adjust this value according to the planned date Shut Down Enabled = DISABLE TCH Rate Adjust Allow = YES Allow Dynamic Shutdown TRX = NO HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 33
33
Configure GTRXCHAN
Set Channel Type to ‘PDTCH’ of Channel No. 6 of the Main BCCH TRX --According to the planned data HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 34
34
Add PTP BVC
Transport -> MBSC -> GSM -> GB -> PTP BVC Configure PTP BVC according to the planned data HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 35
35
Add AdjNode
Transport -> MBSC -> GSM -> Abis -> Adjacent Node Add adjnode according to the planned data Adjacent Node Name = BTS Name HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 36
36
Add AdjMap
Transport -> MBSC -> GSM -> Abis -> Adjacent Node Mapping Gold user TRMMAP index = 43 Factor table index =20 HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 37
37
Add IP Path
Transport -> MBSC -> GSM -> Abis -> IP Path Add IP path according to the planned data HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 38
38
Add IP Route
Transport -> MBSC -> GSM -> Abis -> IP Route Fill the Subrack No. and Slot No. according to the planned data. Destination IP address is the ip segment of BTS traffic IP Destination address mask is the mask of BTS traffic IP Forward route address is the gateway of BSC port IP HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 39
39
Export MML Script
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 40
40
The MML folder
Click the link. You can open the folder contains the MML script.
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 41
41
Thank you www.huawei.com
42