02 RA22714EN01GLA0 Flexi Multiradio Installation

Flexi Multiradio BTS GSM/EDGE Installation


For internal use only 1 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

1


Nokia Siemens Networks Academy Legal notice Intellectual Property Rights All copyrights and intellectual property rights for Nokia Siemens Networks training documentation, product documentation and slide presentation material, all of which are forthwith known as Nokia Siemens Networks training material, are the exclusive property of Nokia Siemens Networks. Nokia Siemens Networks owns the rights to copying, modification, translation, adaptation or derivatives including any improvements or developments. Nokia Siemens Networks has the sole right to copy, distribute, amend, modify, develop, license, sublicense, sell, transfer and assign the Nokia Siemens Networks training material. Individuals can use the Nokia Siemens Networks training material for their own personal self-development only, those same individuals cannot subsequently pass on that same Intellectual Property to others without the prior written agreement of Nokia Siemens Networks. The Nokia Siemens Networks training material cannot be used outside of an agreed Nokia Siemens Networks training session for development of groups without the prior written agreement of Nokia Siemens Networks.


RA22714EN01GLA0

RA22714EN01GLA0

2


Objectives (1/2) After completing this module, the participant will be able to: Theory: • Describe the general work order of installing Flexi Multiradio BTS GSM/EDGE • Describe the installation option for Flexi Multiradio BTS GSM/EDGE • List the installation tools needed for Flexi Multiradio BTS GSM/EDGE • Explain the installation order for stack, wall and pole installation option • Explain the installation order of cabinet for outdoor and cabinet for indoor installation option • Describe how to install the modules for different installation options • Identify the installation of optional items. • Identify the interfaces and connectors of the Flexi Multiradio BTS GSM/EDGE modules and • • • •

Transport sub-modules in respect to configuration Describe the cabling principle for different installation options Explain the feederless solution for Flexi Multiradio BTS GSM/EDGE Describe the antenna system for Flexi BTS GSM/EDGE Describe the example of installation of common configuration for different installation options.


RA22714EN01GLA0

RA22714EN01GLA0

3


Objectives (2/2) After completing this module, the participant will be able to: …. (Cont’d) Practical: • Checking the content delivery and optional items based on specific installation option • Install the module for Flexi Multiradio BTS GSM/EDGE based on specific installation option and configuration.

• Install the optional items needed for Flexi Multiradio BTS GSM/EDGE • Flexi Multiradio BTS GSM/EDGE Module and Transport Module Cabling • Examine for correctly installed the Flexi Multiradio BTS GSM/EDGE for stack, wall, pole, indoor and outdoor cabinet installation options based on checking list

• Demonstrate correctly install, route cables and optical fibers on the Flexi Multiradio BTS GSM/EDGE


RA22714EN01GLA0

RA22714EN01GLA0

4


Content Preparation of Flexi Multiradio BTS GSM/EDGE installation Flexi Multiradio BTS GSM/EDGE Installation Option Flexi Multiradio BTS GSM/EDGE Stack, Wall, and Pole (SWP) Installation Flexi Multiradio BTS GSM/EDGE with Flexi Cabinet for Indoor (FCIA) Installation Flexi Multiradio BTS GSM/EDGE with Flexi Cabinet for Outdoor (FCOA) Installation Flexi Multiradio BTS GSM/EDGE Feederless Solution Flexi Multiradio BTS GSM/EDGE Optional Items/Modules Installation Cabling Principles for Flexi Multiradio BTS GSM/EDGE Installation Installation tools and torque values for Flexi Multiradio BTS GSM/EDGE


RA22714EN01GLA0

RA22714EN01GLA0

5




RA22714EN01GLA0

RA22714EN01GLA0

6


Flexi Multiradio BTS GSM/EDGE Installation Preparation of Flexi Multiradio BTS GSM/EDGE installation


RA22714EN01GLA0

RA22714EN01GLA0

7


Preparation of Installation General work order 1.

Check the tools

2.

Unpack the delivery and handle the modules

3.

Fix adapter mechanics to the plinth (wall & pole installations)

4.

Install the plinth (stack, wall & pole installations) or cabinet

5.

Ground the plinth or cabinet

6.

Install the casings to the plinth

7.

Install transmission sub-module

8.

Install the modules

9.

Install optional modules

10. Connect the cables 11. Connect external power feed 12. Install module front covers


RA22714EN01GLA0

RA22714EN01GLA0

8


Preparation of Installation Handling the modules and unpacking the delivery When handling the modules, always use the antistatic wrist strap as shown in the figure below. The cabinet must be grounded, otherwise the antistatic wrist strap will not work. Refer to Grounding the BTS section.

ESDANTI-STATIC ANTI-STATICWRIST WRISTSTRAPS STRAPS ESD SHOULD BE WORN WHEN SHOULD BE WORN WHEN HANDLINGANY ANYUNIT UNITWHICH WHICH HANDLING DISPLAYSTHE THEESD ESDLOGO LOGO DISPLAYS


RA22714EN01GLA0

NOTE: wrist strap not included in the Flexi EDGE BTS deliveries

RA22714EN01GLA0

9




RA22714EN01GLA0

RA22714EN01GLA0

10


Flexi Multiradio BTS GSM/EDGE Installation Flexi Multiradio BTS GSM/EDGE Installation Option


RA22714EN01GLA0

RA22714EN01GLA0

11


Flexi Multiradio BTS GSM/EDGE Installation Option Stacked installation

Wall installation

Pole installation

Nokia, 3rd party BTS cabinet or SSS installation

Urban feederless site application

Up

to 2 00* m


eter

s

* Up to 40KM with Single mode fiber RA22714EN01GLA0

RA22714EN01GLA0

12


Flexi Multiradio BTS GSM/EDGE Installation Option - Tower or mast installation

BTS modules installed on top of mast or tower • A pole installations BTS modules installed on base of mast or tower • A stack or outdoor cabinet installation • LTE space and optional BBU in cabinet


RA22714EN01GLA0

RA22714EN01GLA0

13


Flexi Multiradio BTS GSM/EDGE Installation Option - Other installation options “Street furniture” installation


“Hidden” installation

RA22714EN01GLA0

RA22714EN01GLA0

14


Flexi Multiradio BTS GSM/EDGE Installation Option - Feederless Site Solution • OBSAI interface: No additional optical converters • Removes coverage losses introduced by long feeder runs • CAPEX savings in antenna system equipment and installation work • Target signal strength can be achieved with lower power level which means savings in OPEX • RF parts mounted next to antennas (no MHAs needed)

Rural Mast Top Site (RFM) RF parts

Fiber, DC

RRH Application : Wide Area Rooftop System module, BBU

Sector 3 Sector 2 1

Sector 1

Up to


2 00 *m

eter s

* Up to 40KM with Single mode fiber RA22714EN01GLA0

RA22714EN01GLA0

15




RA22714EN01GLA0

RA22714EN01GLA0

16


Flexi Multiradio BTS GSM/EDGE Installation Flexi Multiradio BTS GSM/EDGE Stack, Wall, and Pole (SWP) Installation


RA22714EN01GLA0

RA22714EN01GLA0

17


Flexi Multiradio BTS GSM/EDGE Stack, Wall, and Pole (SWP) Installation – General Procedure

2

Casing installation principle

Clearances

Cable routing and cable ties Internal power cables

6 Installing the

Plinth

Installation

Finish Cabling

External power

3 Installing the

modules

Plint on the floor, wall, or pole

Module installation principle

4 Grounding the

7 Grounding the

Antenna cables Optical cables Transmission & alarm cable

9 Power up and

modules

plinth Grounding Principle


8

casings

commissioning the BTS

Installing module front covers

Grounding principle Installation example

Cabling

5 Installing the

Content of Delivery

Commissioning

1

Front panel

Checking

Start

10

RA22714EN01GLA0

General procedure of Flexi Multiradio BTS GSM/EDGE Stack, Wall, and Pole (SWP) Installation : 1. Unpack and check the delivery. 2. Check Clearance 3. Installing the plinth •

For wall or pole installation, the adapter mechanics must be fixed to the plinth beforehand. But it’s not applicable if you are installing version FMFA v.104 of the plinth

•

The procedure of installing the plinth could be of of following: • Anchoring the plinth on the floor. • Mounting the plinth on a wall. • For mounting the plinth on the pole, see: • Mounting the plinth on a pole with VMPB or • Mounting the plinth on the pole with FPKA

4. Grounding the plinth 5. and 6. Installing the casings, modules, and cable entries

RA22714EN01GLA0

18


General procedure of Flexi Multiradio BTS GSM/EDGE Stack, Wall, and Pole (SWP) Installation: …… (cont’d) 5. and 6. Installing the casings, modules, and cable entries Recommended work order: a) If Flexi Power Module (FPMA), Flexi Power DC/DC Module 24V (FPDA), or Flexi Power Rectifier Module (FPRx) install directly on top of the plinth. •

See the instruction on Installing Flexi Multiradio BTS GSM/EDGE Optional Items:  Installing Flexi Power Module (FPMA)  Principles for installing FPRx in Flexi Multiradio BTS configurations

•

Install the back covers for the casings

b) Install the empty casings and install the modules by sliding into the casing. See one of the following: •

Installing modules on the floor (stack)

•

Mounting the modules on a wall

•

Mounting the modules on a pole

Then install the transmission sub-module c) Install cable entries d) If one or any optional modules installed, see the following instructions in document Installing Flexi Multiradio BTS GSM/EDGE Optional Items: •

Installing Flexi Power Module (FPMA)

•

Installing Flexi Power DC/DC Module 24V (FPDA)

•

Installing Flexi Mounting Auxiliary Brackets (FMAA)

•

Installing Flexi System External Alarm (FSEB), FSEB interface signals and connector pin assignments.

•

Installing Flexi System External OVP (FSEC)

•

Installing Location Measurement Unit (LMUB) Outdoor

Instructions for installing modules in Flexi Mounting Shields: •

Installing Flexi Mounting Shield 6U (FMSA)

•

Installing Flexi Mounting Shield 18U (FMSB)

c) Install cable entries

RA22714EN01GLA0

19


General procedure of Flexi Multiradio BTS GSM/EDGE Stack, Wall, and Pole (SWP) Installation: …… (cont’d) 7. and 8. Grounding the modules and connecting cables Cabling principles: •

Cabling principles in stacked, wall and pole installation

•

Cable clamps in stacked, wall and pole installation

•

Optional cable tunnels

•

Internal power cabling principles for System Module (ESMB/C)

The order to connect the cables is as follows: a) Grounding cables b) 48 V DC power feed c) Internal power cables d) Antenna jumper cables e) Optical cables (OPT) f) Transmission cables. See one of the following: •

Connecting FIEA, FIPA, FIQx and FIYx transmission cables without optical transceiver

•

Connecting FIQx and FIYx transmission cables with optical transceiver

•

Connecting FIFA transmission cables

g) Optional cables. See the following instructions in document Installing Multiradio BTS GSM/EDGE Optional Items: •

Flexi Power Alarm (FPA) cables

•

External alarms and controls (EAC) cables

•

Synchronisation cables

•

Local management port (LMP) cables

•

Location Management Unit (LMU) cables

•

Optional Rx Out (RxO)

h) In stack or pole installation, install side cable tunnels (optional). See Installing optional side cable tunnels in document Installing Multiradio BTS GSM/EDGE Optional Items: 9. Power up and Commissioning 10. Installing module front covers

RA22714EN01GLA0

20


Flexi Multiradio BTS GSM/EDGE SWP Installation Content of Delivery – System Module (ESMB/ESMC)

Delivery System Module

Contents of delivery

Version

Product Code

Flexi Multiradio BTS GSM/EDGE Syst em Module

Quantity 1

ESMB

472109

ESMC

472059

Bag Reclosable (15 0 x 2 25/ 20 0 x 260) 0.1 mm

1

M10 Hex Nut

2

B10 washer

2

AWG Single cable terminal lug rubber boots

2

M10 Cableterm (25/35 mm2) Ring

2

Pull-out tool

1


RA22714EN01GLA0

RA22714EN01GLA0

21


Flexi Multiradio BTS GSM/EDGE SWP Installation Content of Delivery – Transmission Sub-Module Transmission Submodule Delivery


System Module

Transmission sub-module

Version

Qua ntity

FIEA

1 Flexi transmission interface E1submodule (FIEA)

4 70247A

Flexi trasnsmission interface Flexbus sub-module (FIFA)

4 71007A

Flexi transmission interface E1/T1 symmetrical submodule (FIPA)

4 70248A

Flexi transmission submodule (FIQA) PW 100Base-T ethernet (RJ48) + 4xE1/T1 symmetrical 120/100 ohm (RJ5) + optional optical GE (SFP)

4 71607A

Flexi tra nsmission sub-mod ule (FIYA) PW 100Base-T ethernet (RJ48) + 4xE1/T1 symmetrical 120/100 ohm (RJ5) + optional optical GE (SFP)

4 71719A

Screws (preinstalled)


Product Code

FIFA

FIPA

FIQA

FIYA

4 RA22714EN01GLA0

RA22714EN01GLA0

22


Flexi Multiradio BTS GSM/EDGE SWP Installation Content of Delivery – RF Module RF Module Deliv ery


RF Module

Flexi Multiradio BTS GSM/EDGE Radio Frequency Module*

Version

Product Code

Qu anti ty 1

RF Module (FXxA) FXDA Flexi MultiradioRFM900

4 72083A

FXEA Flexi Multiradio RFM 180 0

4 72084A

FXCA Flexi Multiradio RFM 8 50

4 72142A

FXDJ Flexi Mult iradio RFM 90 0

4 72143A

FXFA Fle xi Multiradio RFM 1900

4 72166A

Power cable, 2m

Optical cable, 2m

RF Modu le Cable Set: Power cable 2 m

9952 81

1

Optical cab le 2 m

9948 07

1

Optical tranceivers (SFP**)

4707 457

2

* RF Module with fan assembly and without the casings ** SFP=Small Form factor Pluggable SFP IP rating = IP55 with connector rubber gaskets For internal use only 23 © Nokia Siemens Networks

SFP optical transceiver

RA22714EN01GLA0

RA22714EN01GLA0

23


Flexi Multiradio BTS GSM/EDGE SWP Installation Content of Delivery – Plinth and Module Casing Plinth Delivery


Plint h delivery

Flexi Mounting Kit f or Floor, Wall, and Po le

Version

Product Code

Quantity

One FMFA, Optional plinth for installation.

FMFA

Fixin g plate fo r the casing

• Always Used with casings

2

M5 x 8 screws

12

M5 x 12 screws

2

Module Casing Delivery Module casing


Version

Product Code

Flexi BTS Mo dule casing (3U)

EMHA

4 70316A

Quantity 1

3 U ca ble entrie s

2

Two casings

3 U fron t cove r

1

3 U rear cover

1

M5 x 10 screws

4

• Two EMHA, Optional 3U casing and mounting covers front and back

M5 x 6 screws

2

Cage nuts

6 (2 loose, 4 pre-installed)

Maintena nce strap s

2

Groun ding cable

1


RA22714EN01GLA0

3-sector RF module

One ESMB, System Module • One transmission sub-module

RA22714EN01GLA0

24


Flexi Multiradio BTS GSM/EDGE SWP Installation Content of Delivery – Pole Mounting Kit (optional) Pole Mounting Kit (optional) Delivery Pole mou nting kit (optional)


Version

Product Code

Flexi Pole Mounting Kit

FPKA

4 71649A

Quan -tity

Aluminium castings

2

Assembling bolts

2

Module fixing screws

6

Bolt re strainer

2

Check List 

Deliveries are complete.



Equipment is not damaged.


RA22714EN01GLA0

RA22714EN01GLA0

25


Flexi Multiradio BTS GSM/EDGE SWP Installation Clearances Wall installation

Wall installation Note: • In a stack, the minimum side clearance is 75 mm (3 in.). • The recommended clearance for hand tying is 150mm (5.9 in.) For internal use only 26 © Nokia Siemens Networks

Check List 

RA22714EN01GLA0

Stack installation

RA22714EN01GLA0

Site meets the minimum clearances.

26


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing the Plinth – Plinth on the floor Plinth on the floor 1. Check the clearances around the plinth. 2. Turn the rear stopper. 3. Place the plinth on the floor, grounding points facing forward. 4. Bolt on the floor with 4 bolts, 12 mm (0.47 in.) in diameter. Tighten to 49.0 Nm (36.1 ft-lb)


RA22714EN01GLA0

Purpose The plinth is mandatory when the modules are not mounted in an optional cabinet or 19“ rack. Before you start •When choosing the location for the plinth, take into consideration the required maintenance space. For fan maintenance from the back, 500 mm (19.7 in.) back space with side access is required.

RA22714EN01GLA0

27


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing the Plinth – Plinth on the floor Other options for anchoring the plinth are

No wall nearby

Minimum clearance on the back side


RA22714EN01GLA0

Purpose The plinth is mandatory when the modules are not mounted in an optional cabinet or 19“ rack. Before you start •When choosing the location for the plinth, take into consideration the required maintenance space. For fan maintenance from the back, 500 mm (19.7 in.) back space with side access is required.

RA22714EN01GLA0

28


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing the Plinth – Plinth on the Wall

1. 2. 3. 4.

Mark screw locations according to the holes in the plinth and drill holes. Fix the mounting screws on the wall and mount the plinth. Tighten the upper mounting screws. Tighten the lower mounting screws to a torque value of 49 Nm.

Note that the space required between plinths is 100 mm (3.4 inches).


RA22714EN01GLA0

RA22714EN01GLA0

29


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing the Plinth – Plinth on the Wall Antenna

• If second plinth installed, required space between the plinths is 100 mm. • One mounting plinth per two modules is installed on a wall.

CAUTION: Install the modules with front panels facing left or right. Do not install modules so that the front panels face up or down.


Ground

RA22714EN01GLA0

If you are going to install Flexi Power Module (FPMA), it should be installed on the same plinth with the ESMB system module

RA22714EN01GLA0

30


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing the Plinth – Mounting kit for Plinth on the Pole

Pole Mounting Kit (VMPB) There are two pole mounting kits available for mounting the plinth and modules on a pole: • Pole Mounting Kit (VMPB), for pole between 60 mm (2.4 in.) and 120 mm (4.7 in.) in diameter • Flexi Pole Mounting Kit (FPKA), for pole between 60 mm (2.4 in.) and 300 mm (11.8 in.) in diameter


Flexi Pole Mounting Kit (FPKA)

RA22714EN01GLA0

RA22714EN01GLA0

31


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing the Plinth – Mounting Plinth on the Pole with FPKA (1/2) •

• • •

The Flexi Pole Mounting Kit (FPKA) can be used with poles : • between 60 mm (2.4 in.) and 120 mm (4.7 in.) in diameter. • The most commonly used size is 80 mm (3.1 in.). The FPKA can replace the VMPB Pole Mounting kit in installations where the pole diameter is less than 120 mm (4.7 in.). The product code of Flexi Pole Mounting Pole (FPKA) is 471649A. The maximum allowed weight on the FPKA is 160 kg (352.7 lbs). However, each FMFA can support a maximum weight of 50 kg (110.23 lbs). Flexi Pole Mounting Kit (FPKA)

FPKA delivery contents Item

Quantity

FPKA Bracket

1

Bolt M8 x 20

6

Bolt restrainer

2

FPKA bracket strainer

1

Bolt M10 x120 105 mm thread ISO 4762 (DIN912)

2


RA22714EN01GLA0

RA22714EN01GLA0

32


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing the Plinth – Mounting Plinth on the Pole with FPKA (2/2) 1

1.

2

2.

3.

3

4 4.

5.

5

6

6.

Fix the upper mounting bracket on the pole. Attach the mounting bracket screws (M10) on the bracket. Tighten screws to 30 Nm. Fix one side of the lower pole mounting bracket on the plinth with mounting screws (M8). Tighten screws to 20 Nm. Lift the plinth on the pole and fit it to the mounting screws of the pole mounting bracket. Tighten screws (M8) to 20 Nm. Place the counterpart of the lower pole mounting bracket in its place. Tighten screws (M10) to 30 Nm. If a second plinth is required, install it on the other side of the pole mounting bracket. Ground the plinth to the site main ground.

Check List

Nm Note that the length30of mounting screws depends on the diameter of the pole. For internal use only 33 © Nokia Siemens Networks



Plinth is installed according to instructions.



Plinth is level.

RA22714EN01GLA0

RA22714EN01GLA0

33


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing the Plinth – Mounting Plinth on the Pole with VMPB • • • •

The Flexi Pole Mounting Kit (VMPB) can be used for poles: • between 60 mm (2.4 in.) and 300 mm (11.8 in.) in diameter The VMPB is required for poles greater than 120 mm (4.7 in.) in diameter. The product code of Pole Mounting Kit (VMPB) is 469978A. The maximum allowed weight on the VMPB is 160 kg (352.7 lbs). However, each FMFA can support a maximum weight of 50 kg (110.23 lbs).

Blocks

FPKA delivery contents Item

Quantity

Pole Mounting Kit (VMPB)

1

Mounting blocks

2

M8x25 bolts

8

M10x120 bolts

4

M10x200 bolts

4

M10x300 bolts

4

Washers

4


M10x120 bolts

M8x25 bolts

M10x200 bolts

M10x300 bolts

washer

RA22714EN01GLA0

RA22714EN01GLA0

34


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing the Plinth – Mounting Plinth on the Pole with VMPB Pole diameter (mm)

Bolt length (mm)

Hole number*

60 - 90

120

1

95 - 125

120

2

126 - 165

200

1

166 - 210

200

2

211 - 255

300

3

256 - 300

300

4

* Hole numbering is presented in the figure below

• There are 3 different lengths of bolts available and 4 places for bolts in the pole mounting brackets. • When attaching the brackets to the pole, use the shortest possible bolts and the holes whose distance is the closest to the pole diameter. See the table and figure for more details. • A plinth is required for mounting the modules on a pole. In pole installation, the maximum number of modules on a plinth is two.


RA22714EN01GLA0

If the configuration has more than two modules, additional plinths must be installed. Max two 3HU modules.

RA22714EN01GLA0

35


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing the Plinth – Mounting Plinth on the Pole with VMPB

1

Note: with two plinths on opposite sides, the upper adapter still has to be up facing a similar adapter on the other side.

2

4 3

7 5 Detail explanation of each step, can be seen on notes page 6 For internal use only 36 © Nokia Siemens Networks

RA22714EN01GLA0

Steps 1. Fix the upper mounting bracket on the pole and attach the mounting screws on bracket. Make sure that the mounting screws in the upper mounting bracket are in the lower edge of the bracket. 2. Fix one half of the lower mounting bracket on the plinth with the mounting screws. Make sure that the mounting screws in the lower mounting bracket are in the upper edge of the bracket. 3. Lift the plinth on the pole and fit it to the pole mounting bracket's mounting screws. 4. Tighten the mounting screws. 5. Place the counterpart of the lower pole mounting bracket in its place and tighten the screws. 6. Make sure that the plinth is not twisted. When the plinth is in a correct position, tighten the 3 screws in the lower bracket of the adapter mechanics. 7. If a second plinth is required, install it on the other side of the pole mounting bracket. a) Fix the adapter mechanics on the plinth as described in step 1 above. b) Fix mounting screws on the upper pole mounting bracket. c) Lift the plinth on the pole, fit it to the pole mounting bracket's mounting screws and tighten the screws. d) Insert the lower fixing screws to fix the plinth on the lower pole mounting bracket. Tighten the mounting screws. e) Make sure that the plinth is not twisted. When the plinth is in a correct position, tighten the remaining 2 screws in the lower bracket of the adapter mechanics.

RA22714EN01GLA0

36


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing the Plinth – Example installation on Pole FXxAFXxA

• In a pole installation, one plinth can have a maximum of two modules installed. If the configuration has more than two modules, additional plinths must be installed.

FXxA

3+3+3 (60 W) …. 12+12+12 (15 W) configuration on a pole without FPDA/FPMA)

FPMA /FPDA

2+2+2 (60 W) …. 12+12+12 (10 W) configuration on a pole with FPDA/FPMA For internal use only 37 © Nokia Siemens Networks

• Two plinths can be installed on one pair of mounting brackets (on opposite sides of the pole).

ESMB/ ESMC*

• The modules must be installed with front panels facing left or right. Do not install modules so that the front panels face up or down.

FXxA FXxA

ESM B/ES MC

• Installation order varies by configuration. See the figure.

Note :

ESMB/

* ESMC is used if number of TRX more than 18 (up to 36) per BCF

ESMC*

RA22714EN01GLA0

RA22714EN01GLA0

37


Flexi Multiradio BTS GSM/EDGE SWP Installation Grounding the plinth 1. Ground the plinth to the site main ground. Tighten to 8.0-10.0 Nm (5.9-7.37 ft-lb) 2. Connect the wrist strap.

Grounding the plinth (FMFA v. 104 or higher)

Check List




Local grounding (earthing) regulations are followed.



Antistatic wrist strap is used when handling modules.



Plinth is grounded.

RA22714EN01GLA0

RA22714EN01GLA0

38


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing Casing – on Stack 4

1 3 2 1. Note: • The casings are pre-installed with back covers. • In Earthquake Zone 4, the maximum number of modules for stack installations is five. • In Earthquake Zone 4, install side fixing plates on the casings • In Earthquake Zone 2, the maximum allowed height for a stack is 22U. • In pole and wall installations, the maximum modules per plinth is two. • In pole and wall installations, maintenance straps must be installed in the casings. • M5 X 6 screws should be secured with thread locking compound in pole and wall installations For internal use only 39 © Nokia Siemens Networks

2. 3.

4.

Align the holes of the first casing bottom with the fixing studs on the plinth Push the casing back until it stops. Attach the casing to the plinth with M5 X 6 mm screws (6150188). Tighten to 3.5-4.2 Nm (2.58-3.10 ft-Ib) Install the remaining casings as required by the configuration

Check List 

Back covers are properly installed.



Fixing screws are tightened.



Optional: In pole and wall installations, maintenance straps are installed in the front covers.

RA22714EN01GLA0

RA22714EN01GLA0

39


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing Casing – mounting casing/module on a wall/pole Line up the locating marks

Line up the locating marks

11

Note:

22

33

Line up the locating marks

44

Line up the locating marks in the module to help aligning the holes with fixing studs.

10 10

99

7 5

Detail explanation of each step, can be seen on notes page

66

88 For internal use only 40 © Nokia Siemens Networks

RA22714EN01GLA0

TIP: You can pre-assemble the plinth with two modules on the ground and then lift the entire plinth. This is the easiest method especially in pole installation. You can also install the casings into the plinth first and then slide the modules in the casings: Steps 1. Align the holes on the first module's bottom with the fixing studs on the plinth. Tip : Line up the locating marks in the module to help aligning the holes with fixing studs. 2. Push the module back until it stops. 3. Attach the module casing to the plinth with screws. 4. Connect the module grounding cable between the module front panel and the plinth. 5. Align the holes on the second module's bottom with the fixing studs on the first module. Tip :Line up the locating marks in the module to help aligning the holes with fixing studs. 6. Push the module back until it stops. 7. Attach the module casings to each other with screws and spring washers. Secure the screws with glue. 8. Connect the module grounding cable between the module front panel and the plinth.

RA22714EN01GLA0

40


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing Casing – Lifting Standalone BTS

•

• •


Plinth can be pre-assembled with two modules on the ground and then lift the entire plinth. This is the easiest method especially in pole installation. However, user can lift and mount the plinth first and then install the modules and connect cables, similarly as in stack installation.

RA22714EN01GLA0

Lifting a standalone BTS Steps: 1. Attach the lifting eye bolts to the attachment points in the plinth. Lifting eye bolts (M12) are not included in the delivery. You can order the LEKA kit separately from your NSN supplier. 2. Attach the hoisting belt or the rope to the lifting eye bolts. Attach the hoisting belt or rope so that the angle between the belt or rope and the plinth is minimum 60°. The distance between the plinth and the belt or rope is minimum 400 mm (15.6 in.). 3. Lift the BTS carefully to the desired installation height. 4. Mount the BTS. 5. Remove the lifting equipment.

RA22714EN01GLA0

41


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing Modules 1

3

4

2

Note: • In pole and wall installations, install the maintenance strap for back covers. • In pole and wall installations, screws are secured with thread locking compound.


1. Slide the RF module and the System Module into the casings. 2. Attach the module(s) to the casing with M5 X 10 mm screws. Tighten to 3.5-4.2 Nm (2.58-3.10 ft-Ib). 3. Install the transmission sub-module to the System Module. Tighten to 2.7-3.3 Nm (1.99-2.43 ft-Ib). 4. Install the cable entries on both casings. Torque 3.5 to 4.2 Nm.

RA22714EN01GLA0

RA22714EN01GLA0

42


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing Modules – on wall (1/2) 1.

2

4 3

5

7 6

10

9


If the Power Module (FPMA) or Power DC/DC 24V Module (FPDA) is installed, attach the back covers to the casings. 2. Align the holes on the first casing’s bottom with the fixing studs on the plinth. 3. Push the casing back until it stops. 4. Attach the casing to the plinth with M5 x 6 mm (0.2 in.) screws (6150188) using threadlocking compound and tighten. 5. Align the holes on the second casing’s bottom with the fixing studs on the first casing. 6. Push the casing back until it stops. 7. Attach the casings to each other with M5 x 6 mm (0.2 in.) screws using thread-locking compound and tighten 8. Repeat steps 2-7 to install the remaining casings to separate plinths. 9. Slide the module into the casing. 10. Attach the module(s) to the casing with M5 x 25 mm (1.0 in.) screws and tighten.

RA22714EN01GLA0

Steps of installing module on wall: 1.

If the Power Module (FPMA) or Power DC/DC 24V Module (FPDA) is installed, attach the back covers to the casings.

2.

Align the holes on the first casing’s bottom with the fixing studs on the plinth.

3.

Push the casing back until it stops.

4.

Attach the casing to the plinth with M5 x 6 mm (0.2 in.) screws (6150188) using thread-locking compound (medium strength, non-permanent) between 3.5-4.2 Nm (2.58-3.10 ftlb).

5.

Align the holes on the second casing’s bottom with the fixing studs on the first casing.

6.


7.

Attach the casings to each other with M5 x 6 mm (0.2 in.) screws (6150188) using threadlocking compound and tighten 3.5-4.2 Nm (2.58-3.10 ftlb).

8.

Repeat steps 2-7 to install the remaining casings to separate plinths.

9.

Slide the module into the casing.

10.

Attach the module(s) to the casing with M5 x 25 mm (1.0 in.) screws and tighten between 3.54.2 Nm (2.58-3.10 ftlb).

RA22714EN01GLA0

43


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing Modules – on wall (2/2) 11. Attach the fixing plates across the module casings on both sides of the modules and fix with 6 screws and spring washers and tighten between 3.5-4.2 Nm (2.58- 3.10 ftlb). 12. Repeat steps 9-11 to install the remaining modules. 13. Attach the cable entries to the casings with two M5 x 10 mm (0.2 in.) screws (6150240) and tighten between 3.5-4.2 Nm (2.58-3.10 ftlb). a) Fix the screws (do not tighten yet). b) Attach the cable entry to the casing. c) Tighten the screws.

11

13


13

13

RA22714EN01GLA0

Steps of installing module on wall: (cont’d) 11. Attach the fixing plates across the module casings on both sides of the modules and fix with 6 screws and spring washers and tighten between 3.5-4.2 Nm (2.58- 3.10 ftlb). 12. Repeat steps 9-11 to install the remaining modules. 13. Attach the cable entries to the casings with two M5 x 10 mm (0.2 in.) screws (6150240) and tighten between 3.5-4.2 Nm (2.58-3.10 ftlb). a) Fix the screws (do not tighten yet). b) Attach the cable entry to the casing. c) Tighten the screws.

RA22714EN01GLA0

44


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing Modules – on pole (1/2) 1.

2

4 3

5

7 6


If the Power Module (FPMA) or Power DC/DC 24V Module (FPDA) is installed, attach the back covers to the casings. 2. Align the holes on the first casing’s bottom with the fixing studs on the plinth. 3. Push the casing back until it stops. 4. Attach the casing to the plinth with M5 x 6 mm (0.2 in.) screws (6150188) using threadlocking compound and tighten. 5. Align the holes on the second casing’s bottom with the fixing studs on the first casing. 6. Push the casing back until it stops. 7. Attach the casings to each other with M5 x 6 mm (0.2 in.) screws using thread-locking compound and tighten 8. Repeat steps 2-7 to install the remaining casings to separate plinths. 9. Slide the module into the casing. 10. Attach the module(s) to the casing with M5 x 25 mm (1.0 in.) screws and tighten.

RA22714EN01GLA0

Steps of installing module on wall: 1.

If the Power Module (FPMA) or Power DC/DC 24V Module (FPDA) is installed, attach the back covers to the casings.

2.

Align the holes on the first casing’s bottom with the fixing studs on the plinth.

3.


4.

Attach the casing to the plinth with M5 x 6 mm (0.2 in.) screws (6150188) using thread-locking compound (medium strength, non-permanent) between 3.5-4.2 Nm (2.58-3.10 ftlb).

5.

Align the holes on the second casing’s bottom with the fixing studs on the first casing.

6.


7.

Attach the casings to each other with M5 x 6 mm (0.2 in.) screws (6150188) using threadlocking compound and tighten 3.5-4.2 Nm (2.58-3.10 ftlb).

8.

Repeat steps 2-7 to install the remaining casings to separate plinths.

9.

Slide the module into the casing.

10.

Attach the module(s) to the casing with M5 x 25 mm (1.0 in.) screws and tighten between 3.54.2 Nm (2.58-3.10 ftlb).

RA22714EN01GLA0

45


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing Modules – on wall (2/2)

12

12

12

11. Repeat steps 9-10 to install the remaining modules. 12. Attach the cable entries to the casings with two M5 x 10 mm (0.2 in.) screws (6150240) and tighten between 3.5-4.2 Nm (2.58-3.10 ftlb). a) Fix the screws (do not tighten yet). b) Attach the cable entry to the casing. c) Tighten the screws. For internal use only 46 © Nokia Siemens Networks

RA22714EN01GLA0

Steps of installing module on wall: (cont’d) 11. Repeat steps 9-11 to install the remaining modules. 12. Attach the cable entries to the casings with two M5 x 10 mm (0.2 in.) screws (6150240) and tighten between 3.5-4.2 Nm (2.58-3.10 ftlb). a) Fix the screws (do not tighten yet). b) Attach the cable entry to the casing. c) Tighten the screws.

RA22714EN01GLA0

46


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing Modules – Installing transmission sub-module

Installing FIPA/FIEA

The FIQx, FIYx and FIFA sub-modules are installed the same way as the FIPA and FIEA.

1. Align the transmission sub-module in the System Module using the slots on the sides. Push the sub-module in place. 2. Fix the transmission sub-module with 4 x M4 screws using the TORX head screw. Tighten at 2.7-3.3 Nm (1.99-2.43 ft-lb).


RA22714EN01GLA0

Purpose: The transmission sub-module is installed in the System Module (ESMB/C). The submodule is chosen based on the transmission requirements of each site. The transmission sub-module can be installed before or after the System Module is installed.

RA22714EN01GLA0

47


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing Modules – Example for 1+1+1 (60 W) up to 6+6+6 (10 W) For a 1+1+1 up to 6+6+6 configuration, you need the following modules: • one System Module (ESMB/C) • one transmission sub-module (FIxx) • one RF Module (FXxx)

Wall

Pole

Stack Check List




Module back covers and cable entries are installed..



Screws are tightened to the specified torque value.. RA22714EN01GLA0

RA22714EN01GLA0

48


Flexi Multiradio BTS GSM/EDGE SWP Installation Grounding the Modules

1. Connect the grounding cable to the module front panel. 2. Route the grounding cable through the cable entry. 3. Connect the other end of the cable to the plinth. 4. Repeat steps 1-3 with all the modules. Tighten to 3.5-4.2 Nm (2.58-3.10 ft-Ib).

Check List 

Modules are grounded.



Grounding connections are tightened to the correct torque values.


RA22714EN01GLA0

RA22714EN01GLA0

49


Flexi Multiradio BTS GSM/EDGE SWP Installation Grounding the Modules – Example for 1+1+1 (60 W) up to 6+6+6 (10 W) Example of grounding of the module for stack, wall, and stack installation

Wall

Pole

Stack


RA22714EN01GLA0

RA22714EN01GLA0

50


Flexi Multiradio BTS GSM/EDGE SWP Installation Cabling – cable entry & cable clamp

Cable Clamp 1. Route the cables through cable entries. 2. Fix to cable tie points with cable ties.

Cable entry

Caution: Incorrect cables and seals may not provide secured environmental protection.Use only tested IP65 class cables with seals provided by Nokia Siemens Networks.


RA22714EN01GLA0

•The strain relief of cables in stacked floor, wall or pole installation is done with cable clamps attached on the side of the casing. •The cables are fixed with standard cable ties, except for power supply cables. •The fixing of power supply cables is done with special isolating cable clamps, which come with the casing delivery.

RA22714EN01GLA0

51


Flexi Multiradio BTS GSM/EDGE SWP Installation Cabling – external power cables External power cables 1.

1 2 4 3

6a 5 6b


8

7

9

Install the cable clamp on the side of the casing. 2. Remove the black rubber boots, nuts, washers and cable lugs from the terminals. 3. Strip about 2 cm (.8 in) of insulation from the (+) and (-) DC cables. 4. Insert the stripped end of each cable into a cable lug and crimp. 5. Pull each cable through a rubber boot. 6a.Connect the (-) crimped wire to the (-) connector pole, insert washer, and tighten the nut. Connect the (+) crimped wire to the (+) connector pole, insert washer, and tighten the nut. 6b.Torque the M10 nuts (max 14 Nm). 7. Pull the black rubber boots over the lugs. 8. Route the cable through the external cable entry. 9. Route the power cables through the cable clamp, attach and tighten the cable clamp screws with a T10 TORX screwdriver.

RA22714EN01GLA0

RA22714EN01GLA0

52


Flexi Multiradio BTS GSM/EDGE SWP Installation Cabling – example of external power cables for 1+1+1 up to 6+6+6 (a)

(b) External power cables in a 1+1+1 up to 6+6+6 wall and pole configuration Note: • The allowed 48 V DC cable cross-section size for the System Module (ESMB/C) is 21- 35 mm2 (0.82-1.37 sq. in. or 4-2 AWG) that can be used. • Nokia Siemens Networks recommends to locally source the exact lug sizes when the DC cable thickness is 25 mm2 (4 AWG or 0.98 in2) or less.

External power cables in a 1+1+1 up to 6+6+6 stack configuration without (a) and with (b) EAC For internal use only 53 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

53


Flexi Multiradio BTS GSM/EDGE SWP Installation Cabling – internal power cables Internal power cables

1. Remove the connector seal on the module to uncover the connector. 2. Connect the cable to the System Module. 3. Push the connector seal firmly in place. 4. Connect the other end of the internal power cable to the RF Module. Push the cable connector seal firmly in place.


RA22714EN01GLA0

RA22714EN01GLA0

54


Flexi Multiradio BTS GSM/EDGE SWP Installation Cabling – example of internal power cables for 1+1+1 up to 6+6+6

Internal power cables in a 1+1+1 up to 6+6+6 stack configuration

Internal power cables in a 1+1+1 up to 6+6+6 wall and pole configuration

Connecting internal power cables for a 1+1+1 up to 6+6+6 configuration Number Cable From-to 1


995281

PWR (System Module) - PWR IN (RF Module)

RA22714EN01GLA0

RA22714EN01GLA0

55


Flexi Multiradio BTS GSM/EDGE SWP Installation Cabling – antenna cabling Antenna cabling 1 2

3


1. Remove the connector seal on the module to uncover the connector. 2. Remove seals from the antenna connectors. Store the connector seals for later use. 3. Connect the cable to the antenna connectors. 4. Route the antenna cables through the cable entry. 5. Tighten the connector with a torque wrench set to 25 Nm. 6. Repeat the previous steps for all antenna cables required for your configuration.

RA22714EN01GLA0

Purpose: Jumper cables are connected to the antenna connectors in the front panel of the RF Module (FXxx) and the other end of the jumper cables are carefully connected to the respective feeder cables. The number of cables used depends on the configuration. While connecting the antenna jumper cables, consider the following guidelines: ☞ Connect the antenna cables starting from the module closest to the plinth. ☞ It is recommended to the start connecting the jumper cable from ANT (Tx/Rx) connector closest to the direction of routing. For example, in stack installations, – If you are routing all jumper cables to the right, then the order to be followed isANT 1, ANT 3, ANT5, ANT 2, ANT 4 and ANT 6. – If you are routing all jumper cables to the left, then the order to be followed is ANT 5, ANT 3, ANT1, ANT 6, ANT 4 and ANT 2. – If you are routing 3 jumpers cable to the left and right, the order to be followed is ANT 1, ANT 2 and ANT 3 to the right and ANT 4, ANT 5 and ANT 6 to the left of the RF Module. ☞ Antenna jumper cables can be routed out the left side, right side, or both sides. However, access to the optical and internal power cables during maintenance and expansion is easier when all antenna jumper cables are routed to the right. ☞ To avoid cabling rework, check that the unit powers on before tying down the cables. Follow these guidelines when selecting antenna jumper cables: • 1/2" or 3/8" jumper cables are permitted • One end of the jumper cable must be right angle male for connection to modules (other end depends on site configuration) • 1/2" feeder cable can be connected directly to the modules if a right angle male connectoris used. The maximum allowed feeder cable is 1/2" with right angle connectors. • The length should be determined based on the Flexi Multiradio BTS installation option (for example pole, wall, cabinet, 3rd party cabinet) and the distance of the BTS from the antenna feeder line. • Antenna jumper cables must be rated IP65.

RA22714EN01GLA0

56


Flexi Multiradio BTS GSM/EDGE SWP Installation Cabling – example antenna cabling for 1+1+1 up to 6+6+6 (1/2) Antenna jumper cables in 1+1+1 up to 6+6+6 2UD configuration with unchained RF Modules in stack routed toward the right

Antenna jumper cables in 1+1+1 up to 6+6+6 2UD configuration with unchained RF Modules in stack routed toward the left


RA22714EN01GLA0

RA22714EN01GLA0

57


Flexi Multiradio BTS GSM/EDGE SWP Installation Cabling – example antenna cabling for 1+1+1 up to 6+6+6 (2/2)

Antenna jumper cables in 1+1+1 up to 6+6+6 2UD configuration with unchained RF Modules in stack routed to left and right Antenna jumper cables in 1+1+1 up to 6+6+6 2UD wall and pole configuration Note : • Antenna jumper cables can be routed out the left side, right side, or both sides for stack installation • For wall and pole installation, antenna jumber must be routed to the lower side of module For internal use only 58 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

58


Flexi Multiradio BTS GSM/EDGE SWP Installation Cabling – transmission cables Transmission cables

1 2

3 5 4


1. Remove the connector seal(s) from the connector. 2. Route the cable through the cable entry. 3. Pull back the connector seal covering the cable (Flexbus connector excluded). 4. Connect the cable to the appropriate connector. 5. Push the cable connector seal firmly in place. 6. Repeat the previous steps for all cables. 7. Make sure the that all the connector seals are properly installed.

RA22714EN01GLA0

RA22714EN01GLA0

59


Flexi Multiradio BTS GSM/EDGE SWP Installation Cabling – example connecting transmission cables for 1+1+1 up to 6+6+6 using FIEA, FIPA, FIQA and FIYA without optical transceiver

Transmission cables in a 1+1+1 up to 6+6+6 stack configuration


Transmission cables in a 1+1+1 up to 6+6+6 wall and Pole configuration

RA22714EN01GLA0

RA22714EN01GLA0

60


Flexi Multiradio BTS GSM/EDGE SWP Installation Cabling – example connecting transmission cables for 1+1+1 up to 6+6+6 using FIFA 1. Route the Flexbus Jumper cable through the cable entry and connect the Flexbus Jumper cable to FIFA, Flexbus 1 interface.

1

2

2. Connect the Flexbus Jumper cable to Flexbus cable (from the outdoor unit).

3

3. Add weatherproof protection tape on the Flexbus Jumper Cable and Outdoor Flexbus cable connection. 4. If there is Flexbus 2 in use, repeat the steps and connect the Jumper cable to Flexbus 2 interface. 4

Note that a Flexbus Jumper cable must be used to interconnect the FIFA Flexbus interface and the Flexbus cable from the outdoor unit. For internal use only 61 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

61


Flexi Multiradio BTS GSM/EDGE SWP Installation Cabling – optical cabling (1/2) 1. Remove connector seal from OPT1 connector in ESMB/C. 2. Remove protective cap from optical transceiver and insert it into OPT1 in ESMB/C. 3. Route optical cable through cable entry. 4. Uncover the connector. Pull back the optical cable connector seal to uncover the connector. 5. Remove protective plugs. 6. Clean connectors with 99% alcohol and swabs. 7. Connect optical cable to optical transceiver in ESMB/C. 8. ……. Cont’d

Optical cabling

1

4

2

7

8 …… Cont’d For internal use only 62 © Nokia Siemens Networks

Caution: Overbending optical fiber cables damages the cables and can detach or damage the connectors. Do not bend optical fiber cables to a radius smaller than the minimum radius of 70 mm (3 inches).

RA22714EN01GLA0

RA22714EN01GLA0

62


Flexi Multiradio BTS GSM/EDGE SWP Installation Cabling – optical cabling (2/2) 8. Push connector seal firmly. 9. Repeat steps 1-8 to connect optical transceiver and optical cable to OPT1 of FXxx. 10. Ensure all connector seals are properly installed.

Optical cabling

8

Check List       For internal use only 63 © Nokia Siemens Networks

DC power cables are connected and the cable clamp is in place. Connector seals are firmly in place. All cables are connected according to the configuration. BTS external cables or cables between the modules on different plinths are routed via cable entries. Connector seals are firmly in place. To avoid cabling rework, check that the unit powers on before tying down the cables.

RA22714EN01GLA0

RA22714EN01GLA0

63


Flexi Multiradio BTS GSM/EDGE SWP Installation Cabling – example of connecting optical cables for 1+1+1 up to 6+6+6

Optical cables in 1+1+1 up to 6+6+6 stack configuration Optical cables in 1+1+1 up to 6+6+6 wall and pole configuration Connecting optical cables for a 1+1+1 up to 6+6+6 configuration Number Cable From-to 1 For internal use only 64 © Nokia Siemens Networks

994807D

OPT1 (System Module) - OPT1 (RF Module)

RA22714EN01GLA0

RA22714EN01GLA0

64


Flexi Multiradio BTS GSM/EDGE SWP Installation Powering up and commissioning the BTS

1. Power up the site and check the LEDs. 2. Commission the BTS.


RA22714EN01GLA0

RA22714EN01GLA0

65


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing module front covers Maintenance strap 1

1

Module front covers

1

2

3 1. Fix the maintenance strap. (Pole or wall only) Attach the first and second snap hooks of the maintenance strap to the front cover. Attach the third snap hook of the maintenance strap to the external cable entry. 2. Place the cover on top of the module front panel. 3. Fix the screws. Tighten the screws to 2.0 - 2.5 Nm (1.5-1.8 ft-Ib) Check List 

Module front panel covers are installed.


RA22714EN01GLA0

Purpose Module back and front covers complete IP65 protection for core modules. Back and front covers are required for safety reasons, in all installations including indoor installations. Note: •The front panels of the modules are hot during operation. If Flexi Multiradio BTS modules are not installed in a cabinet, front covers must be used during operation for safety reasons and should only be removed temporarily for maintenance. •Rotating fan blades can cause personal injury. If Flexi Multiradio BTS modules are not installed in a cabinet, back covers must be used during operation for safety reasons and should only be removed temporarily for maintenance. Before start: ☞ When there is no risk of dropping the covers, safety catches are not needed. ☞ To avoid cabling rework, check that the unit powers on before tying down the cables.

RA22714EN01GLA0

66


Flexi Multiradio BTS GSM/EDGE SWP Installation Installing module back covers Installing back cover

3U casings comes with back covers preinstalled. Install the back covers before installing the modules. In case it’s not installed, here is the procedure: 1. Attach the first and second snap hooks of the safety catch to the back cover. 2. Attach the third snap hook of the safety catch to the rear of the casing. 3. Install the back cover in the rear of the module and fix the screws (TORX T25). Tighten to 2.0 - 2.5 Nm (1.5-1.8 ft-lb). For internal use only 67 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

67


Flexi Multiradio BTS GSM/EDGE SWP Installation Removing modules with the pull-out tool (for maintenance only) Removing System Module with the pull-out tool

4

1. 2. 3. 4.

Cautions: Do not completely remove the module or carry it with the pull-out tool.

Remove the front covers and cable entries. Remove the module screws. Hook the pull-out tool through the hole in front of the module. Pull until the unit comes loose.


RA22714EN01GLA0

RA22714EN01GLA0

68


Flexi Multiradio BTS GSM/EDGE SWP Installation Installation Checklist (1/4)

 Delivery is complete and undamaged.  Site meets the minimum clearances.  Adapter mechanics are installed (for wall and pole      

installation) Plinth is installed according to the instructions. Plinth is grounded. Transmission sub-module is installed according to the instructions. If power modules (FPDA or FPMA) are used, back covers are installed on them. Modules are installed according to the instructions. Cable entries are installed.


RA22714EN01GLA0

RA22714EN01GLA0

69



     

One module per casing is grounded to the plinth. External power cables are connected. Internal power cables are connected. Optical cables are connected. Antenna jumper cables are connected. Transmission cables and sub-modules are connected, and in case the FIQA/FIYA is used in the PWE mode and the PW traffic is transmitted via Gigabit Ethernet, the optical transceiver is installed.

 Optional cables (EAC, Synchronisation, Site support interface, FPA interface, LMP, LMU cables) are connected. For internal use only 70 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

70



 BTS external cables or cables between the modules on different plinths are routed via cable entries.

 Cables between the modules on the same plinth are routed via internal cable entries.

 All boots and caps are properly connected and IP-sealed.  Cables used are provided by Nokia Siemens Networks (excluding site grounding, external power and antenna jumper cables).

 Screws are tightened to the specified torque value. Note: In pole and wall installations, screws are secured with thread locking compound. For internal use only 71 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

71



 Only IP65 class cables with seals provided by Nokia Siemens Networks are used.

 BTS is switched on and all units are ready.  Module front covers are installed.  Site is clean and installation completed.


RA22714EN01GLA0

RA22714EN01GLA0

72




RA22714EN01GLA0

RA22714EN01GLA0

73


Flexi Multiradio BTS GSM/EDGE Installation Flexi Multiradio BTS GSM/EDGE with Flexi Cabinet for Indoor (FCIA) Installation


RA22714EN01GLA0

RA22714EN01GLA0

74


Flexi Multiradio BTS GSM/EDGE with Flexi Cabinet for Indoor (FCIA) – General Procedure Start

2

Contents of Delivery

5 Installing the Anchoring the cabinet

Clearances Minimum Clearance Fixing points

Finish

8

cabinet Cabling Principles

6 Grounding the

Cabling

Checking

1

cabinet

Lifting the cabinet Lifting the cabinet with rope Lifting the cabinet With handles


7

Installing the Modules Recommended Installation order

9 Routing cabinet external cabling

Installation example

10

Installing Checklist

Checklist

4

Changing the door opening direction

Module Installation

Cabinet Installation

3

RA22714EN01GLA0

RA22714EN01GLA0

75


Flexi Cabinet for Indoor (FCIA) Installation Contents of Delivery Delivery


Versi on

Flexi Cabinet for Indoor (FCIA)

Product Code

Nokia Flexi Cabinet for Indoor (FCIA)

470152AA

Cabinet key

6490006

Cage nuts (62 pcs)

1800

Site package 1 Guide plates (30 pcs)

822083

Loose cage nuts (28 pcs)

6332594

Site package 2

600 600

Check List  Delivery is complete. 



RA22714EN01GLA0

RA22714EN01GLA0

76


Flexi Cabinet for Indoor (FCIA) Installation Clearance Minimum clearances

Fixing points

NOTE: Maintenance space is not included.

Check List  Site meets the minimum clearances. For internal use only 77 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

77


Flexi Cabinet for Indoor (FCIA) Installation Changing the door opening direction (1/2) Principle of changing the door opening direction

1

2

3

1. Remove the ground wire and hinge pins, and detach the door. 2. Loosen the hinge screws and remove the hinges. 3. Install the hinges on the opposite side of the cabinet. 4. …cont’d

NOTE: If changing the handedness of the door is not needed, skip next step


RA22714EN01GLA0

RA22714EN01GLA0

78


Flexi Cabinet for Indoor (FCIA) Installation Changing the door opening direction (2/2) Principle of changing the door opening direction (cont’d)

4

6

5

Check List  Door opening direction and sensor is changed. For internal usemagnetic only 79

© Nokia Siemens Networks

RA22714EN01GLA0

4. Remove the door lock-plate. 5. Install the door lock-plate on the opposite side of the cabinet. 6. Flip the door end-to-end. 7. Mount the door on the opposite side. Reinstall the ground wire after attaching the hinge pins.

RA22714EN01GLA0

79


Flexi Cabinet for Indoor (FCIA) Installation Lifting the Cabinet Lifting the cabinet with a rope

Lifting the cabinet with WLHA handles

2 Minimum 500 mm (19.6 in.)

1

1 2

1. 2. 3. 4.

Attach the 4 x M12 lifting eye bolts to the lifting points. Attach the hoisting belt or rope to the lifting eye bolts. Lift the cabinet carefully to the desired installation location. Remove the lifting equipment.

1. 2. 3. 4.

Align the handle screw holes with the four M5 screw holes on the side of the cabinet. Fix the handles to the cabinet with four M5 screws provided with the kit. Lift the cabinet carefully to the desired installation location. Remove the lifting equipment.


RA22714EN01GLA0 TIP: It is possible to lift the cabinet with modules installed and internal cabling completed.

RA22714EN01GLA0

80


Flexi Cabinet for Indoor (FCIA) Installation Installing the cabinet Anchoring the cabinet

1. Mark the anchoring bolt holes with the help of the drilling template. 2. Drill the anchoring bolts holes on the base. 3. Attach the anchoring bolts to the base. 4. Position the cabinet on the anchoring bolts. 5. Fix the nuts on the anchoring bolts. 6. Check that the cabinet is level. 7. Tighten the nuts properly (recommended 49.0Nm (36.1 ft-lb)).

Note that the cabinet should be attached to the base with M10 or M12 anchor bolts, nuts, and washers (4 pcs each). The recommended anchor bolt length is 60 mm (2.36 inches). Anchor bolts and nuts are not provided with the Flexi BTS delivery and must be acquired locally.

Check List  Cabinet is anchored according to instructions.


RA22714EN01GLA0

RA22714EN01GLA0

81


Flexi Cabinet for Indoor (FCIA) Installation Grounding the cabinet (1/2) Side view of Cabinet

1. Make sure the grounding cable is fixed to the site grounding point. 2. At the top of the cabinet, remove the screw and star washer. 3. Strip approx. 2 cm (0.79 in.) of the main ground cable. 4. If this is a NEBS installation, bring the mating surfaces of all unplated ground connections to a bright finish, using emerycloth -(or other suitable method). Then coat the exposed ground cable conductor with antioxidant. 5. ….. Cont’d

A

B


RA22714EN01GLA0

RA22714EN01GLA0

82


Flexi Cabinet for Indoor (FCIA) Installation Grounding the cabinet (2/2) Top view of Cabinet

1. Insert the stripped end of the cable into a cable shoe lug and crimp. 2. Fit the lug to the grounding point in the cabinet and fix with a star washer and screw. Tighten M5 to 3.5-4.2 Nm (2.58-3.10 ft-lb). Tighten M8 to 8.0-10.0 Nm (5.9-7.37 ft-lb).

Check List  Cabinet is correctly grounded.


RA22714EN01GLA0

RA22714EN01GLA0

83


Flexi Cabinet for Indoor (FCIA) Installation Installing Modules (1/2) Recommended Installation Order

1

2

3 1. Push the front part of the guide plate in place first, and then the back part. 2. Fix the cage nuts according to the configuration. 3. Slide the first module in. 4. Fix the module to the cabinet with screws. 5. Repeat for each subsequent module.

4

Check List  Modules are installed according to instructions. For internal use only 84 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

84


Flexi Cabinet for Indoor (FCIA) Installation Installing Modules (2/2) Installation Example


RA22714EN01GLA0

RA22714EN01GLA0

85


Flexi Cabinet for Indoor (FCIA) Installation Cabling Principles Cabling Principles

Check List  Cables are correctly routed.  For internal use only 86 © Nokia Siemens Networks

Cables are correctly connected. RA22714EN01GLA0

RA22714EN01GLA0

86


Flexi Cabinet for Indoor (FCIA) Installation Installation Checklist

          

Delivery is complete and undamaged. Cabinet is anchored according to instructions. Cabinet is grounded. Modules are installed according to instructions. External antenna feeder cables are connected. Cables are routed, connected and tied correctly. External transmission cables are connected. External power feed cable is connected. All cable rubber seals are firmly in place. Cables are routed downwards from modules. Cabinet door is closed and locked.


RA22714EN01GLA0

RA22714EN01GLA0

87




RA22714EN01GLA0

RA22714EN01GLA0

88


Flexi Multiradio BTS GSM/EDGE Installation Flexi Multiradio BTS GSM/EDGE with Flexi Cabinet for Outdoor (FCOA) Installation


RA22714EN01GLA0

RA22714EN01GLA0

89


Flexi Multiradio BTS GSM/EDGE with Flexi Cabinet for Outdoor (FCOA) – General Procedure Start

6 Installing the

Fixing points

7 Grounding the cabinet

4

5

Changing the door opening direction Removing the roof Lifting the cabinet Lifting the cabinet with rope Lifting the cabinet With handles


8 Module Installation

Cabinet Installation

3

Cabling Principles

Anchoring the cabinet

Clearances Minimum Clearance

Finish

9

cabinet

Cabling

2

Contents of Delivery

10 Routing cabinet external cabling Routing the cables through cabinet bottom

Installing the Modules

Routing the cables through cabinet roof

Recommended Installation order Installation example

11

Installing Checklist

Checklist

Checking

1

RA22714EN01GLA0

RA22714EN01GLA0

90


Flexi Cabinet for Outdoor (FCOA) Installation Contents of Delivery (1/2) Delivery Flexi OD Cabinet


Version 104

FCOA

Product Code

Flexi Cabinet for Outdoor (FCOA)

470142A

Drilling template

00044699

Air Guide plate (2 pcs)

822990

Cabinet key (1 pcs)

6490006

Cage nuts (56 pcs)

6332594

Support rail (24 pcs)

822133

Cable clamp (2 pcs)

6401026

Screws K30x24 (4 pcs)

6150747

Screws M5x12 (2 pcs)

6150287

Lock latch (1 pcs)

6497988

Loose cage nut (12 pcs)

6332594

Knock-out plate (2 pcs)

824774

Dummy panel (10 pcs)

822546

FCOA Cabinet Quick Guide (1 pcs)

00049229

1550

Site package 1

770

Site package 2

770 Check List 

Delivery is complete.




Cont’d…. For internal use only 91 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

91


Flexi Cabinet for Outdoor (FCOA) Installation Contents of Delivery (2/2) Delivery


Version

Product Code

….cont’d Optional items Air filter delivery

Flexi Cabinet Air filter

FCFA

470146A

Site support delivery

Flexi Cabinet Site Support Module

FCSA

470145A

Flexi Power Rectifier delivery

Flexi Power Rectifier

FPRA

CS7000000

MIBBU delivery (Eltek)

Power Distribution Unit

WPUB

469784A

Wideband Power Unit

WPMB

469950A

Power Distribution Unit

WPUC

469955A

Wideband Power Unit

WPMC

469956A

Battery kit

FMBA

MIBBU delivery (Power-One)

Powersafe battery 48V, 92 Ah

4 batteries with accessories

471020A CS71362.03

Powersafe battery 48V, 62 Ah

4 batteries with accessories

Fire detector delivery

Flexi Cabinet Fire Detector

FCDA

470144A

CS7136211

External alarm delivery

Flexi System External Alarm

FSEB

471424A

Lifting eye bolts kit

Lifting eye bolts (4 pcs)

LEKA

466289A

Lifting handle kit

Lifting handles (2 pcs)

WLHA

469554A


RA22714EN01GLA0

Customer specific lock + key

RA22714EN01GLA0

92


Flexi Cabinet for Outdoor (FCOA) Installation Clearance Minimum clearances

Fixing points

Check List  Site meets the minimum clearances. For internal use only 93 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

93


Flexi Cabinet for Outdoor (FCOA) Installation Changing the door opening direction (1/2) Principle of changing the door opening direction

2

3 1

NOTE: If changing the handedness of the door is not needed, skip next step


4

1. Detach the wind stopper from the door and cabinet. 2. Detach the grounding cable from the door. 3. Remove the hinge pins and detach the door. 4. Remove the hinge screws and hinges from the cabinet 5. .…cont’d Check List  Door opening direction and magnetic sensor is changed.

RA22714EN01GLA0

RA22714EN01GLA0

94


Flexi Cabinet for Outdoor (FCOA) Installation Changing the door opening direction (2/2) Principle of changing the door opening direction (cont’d)

6

5

10 9 6

7

7 8

5. Remove the door lock-plate. 6. Move the hinges to the new location in the cabinet. 7. Flip the door upside down and install it to the cabinet using the hinge pins. 8. Thread the wind stopper to the guiding slot in the cabinet and then attach it to the door. 9. Detach the grounding cable from the cabinet and attach it to the new location. 10. Attach the grounding cable to the door. 11. Move the magnetic proximity sensor magnet part from the bottom of the door to the top. For internal use only 95


RA22714EN01GLA0

RA22714EN01GLA0

95


Flexi Cabinet for Outdoor (FCOA) Installation Removing the Roof 2 1

3

1. Open the cabinet door. 2. Pull the roof forward. 3. Lift the roof up keeping it level.

NOTE: You do not need to loosen or remove any screws when removing the roof.



RA22714EN01GLA0

96


Flexi Cabinet for Outdoor (FCOA) Installation Lifting the Cabinet Lifting the cabinet with a rope

Lifting the cabinet with WLHA handles

3

2 1

1. 2. 3. 4.

Attach the 4 x M12 lifting eye bolts to the lifting points. Attach the hoisting belt or rope to the lifting eye bolts. Lift the cabinet carefully to the desired installation location. Remove the lifting equipment.


1. 2. 3.

Attach the lifting handles with four screws each. Lift the cabinet to the desired location. Remove the lifting handles..

WARNING: The cabinet is heavy. Additional personnel or lifting equipment may be needed when the cabinet is moved, unpacked, or lined up. In addition, follow any local regulations applicable to the installation.


RA22714EN01GLA0

97


Flexi Cabinet for Outdoor (FCOA) Installation Installing the cabinet Anchoring the cabinet

Check List  Cabinet is anchored according to instructions. For internal use only 98 © Nokia Siemens Networks

1. Mark the anchoring bolt holes with the help of the drilling template. 2. Drill the anchoring bolts holes on the base. 3. Attach the anchoring bolts to the base. 4. Position the cabinet on the anchoring bolts. 5. Fix the nuts on the anchoring bolts. 6. Check that the cabinet is level. 7. Tighten the nuts properl (recommended 50Nm (36.87 ft -Ib)). 8. Make sure that any water will run off the installation location.

RA22714EN01GLA0

RA22714EN01GLA0

98


Flexi Cabinet for Outdoor (FCOA) Installation Grounding the cabinet 1. Make sure the grounding cable is fixed to the site grounding point. 2. Guide the cable through the cable entry (see section 10) 3. Strip approx. 2 cm (0.79 in.) of the main ground cable. 4. Insert the stripped end of the cable into a cable shoe lug for two M5 thread bolts or a M8 thread bolt and crimp. 5. Fit the lug to the grounding point in the cabinet and fix with a star washer and nut.

Grounding Points

Check List  Cabinet is correctly grounded. For internal use only 99 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

99


Flexi Cabinet for Outdoor (FCOA) Installation Installing Modules (1/2) Installing the Flexi Multiradio, LTE or WCDMA modules Recommended installation order 1.

1

2

2 3

3

5

4

8 6 9


RA22714EN01GLA0

Remove the fixing studs from the module casings. 2. Remove the cable support plates and their fixing screws from the casings. 3. Loosen the module core fixing screws. 4. Detach the cage nuts and support plates behind them from the module. Caution: Make sure that the module core does not slip out of the casing. 1. Fix the guide plates (from the site pack). 2. If the cage nuts are not in their correct locations by default, move them as required by your configuration. 3. Remove the unnecessary preinstalled cage nuts, if applicable. 4. Slide the module into the cabinet. 5. Fix the module to the cabinet with core fixing screws. 6. Repeat for each subsequent module. 7. Install dummy panels into the empty slots.

RA22714EN01GLA0

100


Flexi Cabinet for Outdoor (FCOA) Installation Installing Modules (2/2) Installing the Flexi Multiradio, LTE or WCDMA modules … cont’d

Installation example, starting from the bottom

NOTE: The appearance of the modules may vary depending on the product or module type. NOTE: Dummy panels are needed to ensure proper cabinet cooling.

Check List  Modules are installed according to instructions.  For internal use only 101 © Nokia Siemens Networks

Dummy panels are installed according to instructions.

RA22714EN01GLA0

RA22714EN01GLA0

101


Flexi Cabinet for Outdoor (FCOA) Installation Installing Modules (1/2) Installing the Flexi EDGE Modules Recommended installation order

2

3

4 1

1. 2.

3. 4. 5. 6.

Fix the guide plates (from the site pack) inside the cabinet. If the configuration is not a 1+1+1/ 2+2+2 or 3+3+3/4+4+4 with the System module in the horizontal rack, fix the cage nuts (from the site pack) inside the cabinet according to the configuration. The cabinet has U-markings printed on the side rails in 1U increments. Check the markings to determine the starting place for module installation. Slide the first module in. Fix the module to the cabinet with screws. Tighten to 3.5-4.2 Nm(2.58-3.10 ft-lb). Repeat for each subsequent module. Install dummy panels into the empty slots.


RA22714EN01GLA0

RA22714EN01GLA0

102


Flexi Cabinet for Outdoor (FCOA) Installation Installing Modules (2/2) Installing the Flexi EDGE modules … cont’d

Installation example, starting from the bottom NOTE: • The appearance of the modules may vary depending on the product or module type. • Dummy panels are needed to ensure proper cabinet cooling. • If the air guide plate in the vertical rack is not required for the configuration, it should be removed. • The air separator plate is required if the System Module or the System Extension Module are installed in the vertical left rack. Otherwise, use dummy panels in the empty slots.

Check List  Modules are installed according to instructions.  For internal use only 103 © Nokia Siemens Networks

Dummy panels are installed according to instructions.

RA22714EN01GLA0

RA22714EN01GLA0

103


Flexi Cabinet for Outdoor (FCOA) Installation Cabling Principles (1/2) Flexi Multiradio, LTE or WCDMA cabling principles

Triple RF Modules:

Triple RF Modules:

Routing cables through the bottom cable entry

Routing cables through the entries on the cabinet roof

Single or Dual RF Modules:

Single or Dual RF Modules:


Routing cables through the entries on the cabinet roof

Check List For internal use only 104 © Nokia Siemens Networks



Cables are correctly routed.



Cables are correctly connected.

RA22714EN01GLA0

RA22714EN01GLA0

104


Flexi Cabinet for Outdoor (FCOA) Installation Cabling Principles (2/2) Flexi EDGE cabling principles


Routing cables through the top cable entry

Check List For internal use only 105 © Nokia Siemens Networks



Cables are correctly routed.



Cables are correctly connected.

RA22714EN01GLA0

RA22714EN01GLA0

105


Flexi Cabinet for Outdoor (FCOA) Installation Routing cabinet external cabling (1/4) Routing the cables through cabinet bottom

1.

1 2

3


4

Remove 2 pcs of right hand side M5x12 cable entry fixing screws (6150287) and take the whole panel, including the cable entries, out of the cabinet. 2. Remove the left and right M5x6 fixing screws (6150188) and remove the entry block. If only one entry block is needed leave the other one fixed in place. 3. Route the cables through the bottom and entry box front hole. Do not fix the cables outside of the cabinet. TIP: For easier installation, do not fix cables outside the cabinet. This allows cables to be moved freely. 4. Route the cables through the opening on the sheet metal panel. 5. Remove the blocking plugs from the entry block. Pull the plugs to remove them from the block. Keep the plugs fore later use.

RA22714EN01GLA0

RA22714EN01GLA0

106


Flexi Cabinet for Outdoor (FCOA) Installation Routing cabinet external cabling (2/4) Routing the cables through cabinet bottom …cont’d

7 9 NOTE: Cable conduit can be routed through the top or bottom of the cabinet using the knock-out plates provided in the site bag. There are three knock-out holes on the back side of the bottom cable entry box.

Check List

 Cables are routed correctly. For internal use only 107 © Nokia Siemens Networks

6.

If necessary, cut the rubber sealing the hole according to your cable thickness. 7. Organize the cables to the top and bottom row and place the entry block center piece in between the rows. Fix the center piece with left and right screws. 8. Place the cables to correct slots and install the top and bottom rubber strips. Block any unused holes with plugs. 9. Push back the whole assembly to the entry box. First position it by the left hook,then fix it with righthand side entry screws. 10. Route the cables to the right positions inside the cabinet. Suitable free length can be adjusted by sliding the cable through the entry hole. 11. Fix the cables outside of the cabinet.

RA22714EN01GLA0

RA22714EN01GLA0

107


Flexi Cabinet for Outdoor (FCOA) Installation Routing cabinet external cabling (3/4) Routing the cables through cabinet roof

1 3 2

6 5 7


1. Detach 2 pcs M5x12 screws (6150287) from the bottom of the cabinet. 2. Detach the cable entry cover together with the cable entries from the bottom of the cabinet. 3. Remove 4 pcs M5x6 screws (6150188) from the bottom of the cabinet. 4. Detach the two cable entries from the bottom of the cabinet. 5. Detach the roof (see section 4 Removing the roof for instructions). 6. Detach 4 pcs M5x6 screws (6150188) from the left-hand side of the inner roof. 7. Remove the two side dummy panels.

RA22714EN01GLA0

RA22714EN01GLA0

108


Flexi Cabinet for Outdoor (FCOA) Installation Routing cabinet external cabling (4/4) Routing the cables through cabinet bottom …cont’d

8 9

12 For internal use only 109 © Nokia Siemens Networks

10

NOTE: • The rubber cable entries are preinstalled at the bottom of the cabinet. If cable routing through the roof is preferred, the entries need to be moved from the bottom to the roof. • The cable tie rails come preinstalled. They can be moved and reinstalled on the left, right or back as desired. • The cable entry blocks can be moved to the back or opposite side of the cabinet.

6.

Fix the upper cables to cable tie rails with cable ties (if needed, cable tie rails can be moved to the right or back side of the roof). 7. Install the two cable entries with 4 pcs M5x6 screws (6150188). See steps 5 and 6 in section 10 8. Routing cabinet external cabling for more detailed instructions. 9. Fix the upper and lower cables through the cable entries. See steps 7 and 8 in section 10 10. Routing cabinet external cabling for more detailed instructions. 11. Reinstall the roof. 12. Install two dummy panels with 4 pcs M5x6 screws (6150188) to the bottom of the cabinet. Check List 

Cables are routed correctly



Cable entries are fixed.



The roof is installed and door closed once the cabling is completed..

RA22714EN01GLA0

RA22714EN01GLA0

109


Flexi Cabinet for Outdoor (FCOA) Installation Installation Checklist (1/2)

      

Delivery is complete and undamaged. Cabinet is anchored according to instructions. Cabinet is grounded. Modules are installed according to instructions. External power feed cable is connected. External antenna feeder cables are connected. External transmission cables are connected.


RA22714EN01GLA0

RA22714EN01GLA0

110


Flexi Cabinet for Outdoor (FCOA) Installation Installation Checklist (2/2)

     

Cables are routed, connected and tied correctly. All cable rubber seals are firmly in place. Cables are routed downwards from modules. Empty slots are covered with dummy plates. Cabinet roof is installed. Cabinet door is closed and locked.


RA22714EN01GLA0

RA22714EN01GLA0

111




RA22714EN01GLA0

RA22714EN01GLA0

112


Flexi Multiradio BTS GSM/EDGE Installation Flexi Multiradio BTS GSM/EDGE Feederless Solution


RA22714EN01GLA0

RA22714EN01GLA0

113


Flexi Multiradio BTS Feederless Solution Overview (1/2) • In a feederless BTS site, RF Module can be installed at a distance from the System Module. • Since Flexi Multiradio BTS has compatible optical OBSAI interfaces in the System Modules and separate optical converters are not required. • Flexi Multiradio feederless site supports: • 1UD, IDD with 2UD, IDD with 4UD with RF Module configurations • 15, 30, 60W Tx power level with RF Module • A maximum of 3 RF Modules for a remote island • 1 shared RF Module and with a maximum distance of 200 m • EDGE license optimization • Dual band with any TRXs belonging to any band, but only 2 bands together • A maximum of 6 sectors • Where the distance is less than or equal to 20 Km and a maximum of 3 RF Modules For internal use only 114 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

114


Flexi Multiradio BTS Feederless Solution Overview (2/2) • For the optical cable connection can use: • with multimode fiber cables  can be up to 200 meters long • with a single mode fiber  can up to 40 km. – The longer cables are not delivered in fixed length but are made on the field based on the required length.

– Characteristics of the optical OBSAI interface can be adapted to needs with the use of standard optical transceivers

• For the power supply distribution concept, can be fed to RF Module : • Through the System Module – The 48 VDC power distribution cable can run up to 100 m for the RF module – In this case, the System Module and the RF Module require separate over voltage protection devices (FSEC).

• Using a remote power supply with AC or DC. – The RF module has external alarm interfaces for the power supply and other generic alarms.


RA22714EN01GLA0

RA22714EN01GLA0

115


Flexi Multiradio BTS Feederless Solution Feederless Site concept From Power distribution ports System Module

• The RF Module can be installed in the same location as the System Module, or at a distance of up to 15 km. • Modules can be installed on a pole, wall, or floor.

FSEC

FSEC

RF Module

FSEC

FSEC

RF Module

FSEC

FSEC

RF Module


RA22714EN01GLA0

The installation of the optical cable between the System Module and RF Module or Remote Radio Head requires two small form-factor pluggable (SFP) optical transceiver units (included in the RF Module delivery) that are plugged into both the System and RF Module or Remote Radio Head. A multimode adapter (included in the 100 m optical cable delivery) is required when two optical cables are connected together. Optical cables are used for creating an optical interface between the System and RF Module or Remote Radio Head. The length of the cables is 50 m or 100 m. In case you need a cable of a specific length, shorten the cable by cutting and splicing it to the required length.

RA22714EN01GLA0

116


Flexi Multiradio BTS Feederless Solution Installation principle with AC power supply Optical fiber

RF Module (48VDC Input)

System Module Power Supply 230 VAC

48 VDC Length < 2m

48 VDC Length < 2m

OVP (FSEC)

Power Module (48VDC Out)

Shielded cable Length < 100m

OVP (FSEC)


Cable shiled is grounded via OVP box

RA22714EN01GLA0

RA22714EN01GLA0

117


Flexi Multiradio BTS Feederless Solution Installation principle with DC power supply Optical fiber

RF Module (48VDC Input)

48 VDC Length < 2m Power Supply 48VDC

48 VDC Length < 2m

System Module

OVP (FSEC)

(48VDC Output)

Shielded cable Length < 100m

OVP (FSEC)


Cable shiled is grounded via OVP box

RA22714EN01GLA0

RA22714EN01GLA0

118


Flexi Multiradio BTS Feederless Solution Contents of the optical cable deliveries Contents of the optical cable deliveries

Cable type

Product code

Description

FSFB Flexi System FibreB 50m

471395A

Multimode LC to LC fibre

FSFC Flexi System FibreC100m

471396A


FSFF Flexi System FibreF10m

471707A


FSFG Flexi System FibreG 20m

471708A


FSFH Flexi System FibreH 30m

471709A


FSFI Flexi System FibreI 40m

471710A


FSFK Flexi System FibreK 75m

471711A


FSFP Flexi System FibreP 200m

471712A


FSFD Flexi System FibreD 4m

471743A


FSFO Flexi System FibreO HF 2m

471851A

Multimode LC to LC fibre LSZH version*

FSFQ Flexi System FibreQ HF 50m

471852A

Multimode LC to LC fibre LSZH version*

FTCH Single Mode 1310 LC1310 15m

470311A

Singlemode LC to LC fibre

* LSZH = Low Smoke Zero Halogen


RA22714EN01GLA0

RA22714EN01GLA0

119


Flexi Multiradio BTS Feederless Solution Installing Flexi System External OVP (FSEC) - Overview • The Flexi System External OVP (FSEC) assembly protects the Flexi Multiradio BTS modules against surge pulses in power feeding lines. • There are three versions of the FSEC, which are separated from each other by the first two digits of the factory code: From Power – 6Yxxxxxxxxx distribution ports – E4xxxxxxxxx System installation example with three Module – S1xxxxxxxxx RF Modules

• There are two mounting kits for the FSEC: – Flexi Mounting Auxiliary Brackets (FMAA) for stack installations – Flexi Pole Installation Kit (FPIA) for pole and wall installations


RF Module

FSEC

FSEC

FSEC

FSEC

RF Module

FSEC

FSEC

RF Module

RA22714EN01GLA0

RA22714EN01GLA0

120


Flexi Multiradio BTS Feederless Solution Installing FSEC - Installation position (1/3) • If using Flexi Mounting Auxiliary Brackets (FMAA), see the following figures for the installation position of the FSEC on the module casing. FMAA with FSEC

FMAA with two FSECs


RA22714EN01GLA0

RA22714EN01GLA0

121


Flexi Multiradio BTS Feederless Solution Installing FSEC - Installation position (2/3) • If using Flexi Mounting Auxiliary Brackets (FMAA), see the following figures for the installation position of the FSEC on the module casing. FMAA with FSEB and FSEC


RA22714EN01GLA0

RA22714EN01GLA0

122


Flexi Multiradio BTS Feederless Solution Installing FSEC - Installation position (3/3) • The FSEC can also be installed on the FCOA roof. The fixing points on the cabinet roofare illustrated in the following figure. FSEC fixing points on the FCOA roof


RA22714EN01GLA0

RA22714EN01GLA0

123


Flexi Multiradio BTS Feederless Solution Installing FSEC - Installation Procedure (1/5) 1. 1

Open the lid of the FSEC box. If you have version S1xxxxxxxxx, remove the protector board from inside the FSEC at this point to make connecting the wires easier.

2.

Install the box. The maximum installation distance of the FSEC is 1.5 m (59.1 in) from the RF Module.

2. Cont’d ……In pole 2a

2b

installations, use the fixing kit:

a) Thread the straining straps to the installation plate.

b) Tighten the straining straps around the pole. For internal use only 124 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

124


Flexi Multiradio BTS Feederless Solution Installing FSEC - Installation Procedure (2/5)

3

4

3.

4

Connect the grounding cable (GND). Route the grounding cable from the bottom right corner of the FSEC box to the grounding point on the plinth.

4.

Cut the DC cable included in the delivery close to the connector, strip it as necessary to reveal the black and blue wires and connect the wires


4

RA22714EN01GLA0

RA22714EN01GLA0

125


Flexi Multiradio BTS Feederless Solution Installing FSEC - Installation Procedure (3/5) 48V system floating or 48V system positive grounding 5.

6

Connect the other end of the DC cable to the RF Module.

6

Make sure that the seal cap is in place.

6.

Connect the DC feeder cable to the FSEC box as shown in the figures. Connecting DC cable to Dual RF Module 5

+24V/48V system, negative grounding 6

6

6

Connecting DC feeder cable to FSEC (6Yxxxxxxxxx)


RA22714EN01GLA0

Note: • The colours of the cables may vary depending on the country or cable type. • The shielding of the feeder cable must be connected to the PE terminal at both ends.

RA22714EN01GLA0

126


Flexi Multiradio BTS Feederless Solution Installing FSEC - Installation Procedure (4/5) 7. 8. 9.

Route the DC cable to the System Module. If S1xxxxxxxxx is used, reinstall the protector board. Install the module front covers.

7


RA22714EN01GLA0

RA22714EN01GLA0

127


Flexi Multiradio BTS Feederless Solution Installing FSEC - Installation Procedure (5/5) 7.

If used, connect the alarm cable (not included in the FSEC delivery).

8.

Repeat steps 4-7 for connecting the FSEC to the System Module.

9.

Check the FSEC connections and close the box.

10

12


RA22714EN01GLA0

RA22714EN01GLA0

128




RA22714EN01GLA0

RA22714EN01GLA0

129


Flexi Multiradio BTS GSM/EDGE Installation Installing Optional Items/modules: • Installing Flexi System External Alarm (FSEB) • Installing Flexi Power Module (FPMA) • Installing Flexi Power Rectifier (FPRA)


RA22714EN01GLA0

RA22714EN01GLA0

130


Flexi Multiradio BTS GSM/EDGE Installation Installing Optional Items/modules: • Installing Flexi System External Alarm (FSEB) • Installing Flexi Power Module (FPMA) • Installing Flexi Power DC/DC Module 24V (FPDA) • Installing Flexi Power Rectifier (FPRA)


RA22714EN01GLA0

RA22714EN01GLA0

131


Installing Flexi System External Alarm (FSEB) Overview • The optional Flexi System External Alarm Module (FSEB) is used when up to 24 external alarm inputs and 6 control outputs need to be supported with Flexi Multiradio BTS. • The FSEB can be installed in the following ways: – On a wall (vertical or horizontal position) – On a module casing in pole, wall, or stack installations using Flexi Mounting Auxiliary Brackets (FMAA).

– In the FCIA or FCOA roof (horizontal position only) – In Citytalk cabinets, the FSEB can be installed on top of the stack (depending on working space) or outside of the cabinet. The box cannot be installed on the roof.

• The module also supports Flexi Cabinet Fire Detector (FCDA). • If there is not enough space left for the FSEB or other auxiliary boxes on the FCIA, FCOA, or the FMAA, the additional auxiliary box(es) must be installed on a wall or pole close to the BTS. • In stack, wall or pole installations, additional FMAA brackets can also be installed if there are multiple plinths. Note that the distance from each box to the BTS is limited by the lengths of the cables coming from the auxiliary box.


RA22714EN01GLA0

RA22714EN01GLA0

132


Installing Flexi System External Alarm (FSEB) Installation Position (1/3) FMAA with FSEB

installation position of the FSEB on the module casing.

FMAA with FSEB and FSEC


RA22714EN01GLA0

Before installing the FSEB, see FSEB interface signals and connector pin assignments. In pole or wall installations, locate the box in the proximity of the System Module. In wall installations, make sure that the mounting surface is flat. The distance from the FSEB to the System Module is limited by the length of the alarm cable. If using Flexi Mounting Auxiliary Brackets (FMAA), see the following figures for the

RA22714EN01GLA0

133


Installing Flexi System External Alarm (FSEB) Installation Position (2/3) In FCIA and FCOA installations, use the fixing points on the cabinet roof. FSEB fixing points on the FCIA roof


FSEB fixing points on the FCOA roof

RA22714EN01GLA0

Summary The FSEB can be installed either horizontally (cable lead-ins on the side) or vertically (cable lead-ins facing downwards, or left or right). See the following figures for the two installation options.

RA22714EN01GLA0

134


Installing Flexi System External Alarm (FSEB) Installation Position (3/3) Note : In outdoor installations, the cable lead-ins must be facing downwards, left or right to meet the IP65 standard.

FSEB installed horizontally

FSEB connectors

FSEB installed vertically

Fixing FSEB cables


When the cable is routed down, tie the cable a maximum of 500 mm (19.7 in.) away from the FSEB to prevent the weight of the cable to break the cable lead glands of the FSEB. RA22714EN01GLA0

• When connecting the cables, make sure that the cable lead-ins that are not used are blocked. • A module ground cable is not included in the FSEB delivery. The minimum crosssection of the cable should be 2.5 mm2 (14 AWG). The length of the cable should be determined based on the FSEB installation option (for example pole, wall, cabinet, 3rd party cabinet) Summary • The FSEB can be installed either horizontally (cable lead-ins on the side) or vertically (cable lead-ins facing downwards, or left or right). See the following figures for the two installation options.

RA22714EN01GLA0

135


Installing Flexi System External Alarm (FSEB) Installation procedure (1/3)

1

1.

Install FSEB with four M5 screws using the fixing holes in the bottom of the box.

2.

Ground the box using the grounding screw on the right side of the FSEB front plate.

3.

Connect the ESD wrist strap first to your wrist and then to the grounding clip next to the grounding screw.

4. 5.

Open the lid of the FSEB box. Connect the external alarms cable (included in the FSEB delivery) from the FSEB to the System Module. See the notes page for detail.

3 5a

5c 5b

2 5e 5d


5g 5f

5i

RA22714EN01GLA0

Steps: 1.

Install FSEB with four M5 screws using the fixing holes in the bottom of the box.

2.

Ground the box using the grounding screw on the right side of the FSEB front plate.

3.

Connect the ESD wrist strap first to your wrist and then to the grounding clip next to the grounding screw.

4.

Open the lid of the FSEB box.

5.

Connect the external alarms cable (included in the FSEB delivery) from the FSEB to the System Module. a) Pull the left U-shaped cable gland from the FSEB box. b) Remove the hole closing plug from the cable gland. If the plug is fixed with a cable tie, cut the cable tie first and remove it. c) Insert the cable in the cable gland. The D-Sub plug must point to the inside of the box. d) Connect the D-Sub plug to the leftmost D-Sub connector X1101 (ESM) on the FSEB board. e) Fix the connector fixing screws. f) Insert the U-shaped cable gland to the front plate. g) Insert the cable to the round rubber-seal in front of the U-shaped cable gland. h) Fix the cable with a cable tie. Make sure that the U-gland fixes the cable tightly. The cable must not move inside the gland. i) Route the cable between the FSEB and System Module and fix it with cable ties. The first fixing point must not be further away from the FSEB box than 0.5 m (1.6 ft). j) Remove the cover of the EAC connector on the System Module. k) Insert the other end of the cable with the MDR-36 connector to the EAC connector of the System Module. Make sure that the MDR connector is firmly in place. l) Push the connector cover over the MDR connector and seal the EAC connector at the System Module with this cover.

RA22714EN01GLA0

136


Installing Flexi System External Alarm (FSEB) Installation procedure (2/3) 6.

If you are using an existing alarm cable (cable diameter min. 4-6 mm, ovality 1 mm) with a 37pole D-Sub connector, connect the cable with a DSub connector.

7.

If you are using the separate alarm cables, connect them to the screw terminals

8.

If you are using the control output cables, connect them as figure:


RA22714EN01GLA0

6. If you are using an existing alarm cable (cable diameter min. 4-6 mm, ovality 1 mm) with a 37-pole D-Sub connector, connect the cable with a D-Sub connector as follows: ☞ These two alarm cables can be connected to the EACX-I and EACX-II connectors of the FSEB, respectively. Connect the Flexi Multiradio BTS alarm cables (CS73113.01) 1-12 and 13-24 to EACX-I and EACX-II connectors. Pay attention to connect them to the right EACX connector, otherwise the alarm number and alarm description will not match. After the installation, trigger and verify the alarm condition using the 2G Flexi BTS Site Manager. a) Pull the right U-shaped cable gland from the FSEB box. b) Cut the cable tie off the cable gland. c) Remove the hole closing plug from the cable gland. d) Insert the alarm cable in the cable gland. The D-Sub plug must point to the inside of the box. e) Attach the D-Sub plug to the right 37-pole D-Sub connector X4101 (EACX-I port). f) Fix the connector fixing screws. g) Insert the U-shape cable gland to the front plate. h) Insert the cable to the round rubber-seal in front of the U-shaped cable gland. i) Fix the cable with a cable tie. Make sure that the U-gland fixes the cable tightly. The cable must not move inside the gland. j) Route the cable and fix it with cable ties. The first fixing point must not be further away from the FSEB box than 0.5 m (1.6 ft).

RA22714EN01GLA0

137


7. If you are using the separate alarm cables, connect them to the screw terminals as follows: a) Tighten the cable gland nut. The cable must not move inside the gland. b) Insert the alarm cables in the FSEB box by using the cable glands on the right-side half of the FSEB box. c) Route the alarm cables and fix them with cable ties. The first fixing point must not be further away from the FSEB box than 0.5 m (1.6 ft). d) Attach alarm lines EXT_AL1 to EXT_AL12 using screw terminal blocks X4106-X4109. e) For each alarm input, connect one wire to the GROUND screw terminal blocks X4107 or X4109 and connect one wire to the selected alarm input on screw terminal blocks X4106 or X4108. The alarm inputs are marked on the FSEB board with 'EXT_AL6 ... EXT_AL1' on X4106 and 'EXT_AL12 ... EXT_AL7' on X4108. ☞ If you use alarm inputs on the EACX-I port (D-Sub connector X4101), do not use the same alarm inputs on the screw terminals X4106 and X4108. 8. If you are using the control output cables, connect them as follows: a) Tighten the cable gland nut. The cable must not move inside the gland. b) Insert the control output cables in the FSEB box by using the cable glands on the rightside half of the box. c) Route the control cables and fix them with cable ties. The first fixing point must not be further away from the FSEB box than 0.5 m (1.6 ft). d) Attach the control lines EXT_CO1 to EXT_CO6 by using the screw terminal blocks X4104 and X4105. e) Control outputs are open collector type. Connect a pull-up resistor (2-6 kilohms, 5 kilohms is recommended) or an opto-coupler to +5 V to ensure correct operation. The control outputs are marked on the FSEB board with 'EXT_CO6 ... EXT_CO1‘ on X4104. 

If galvanic isolation is required for the customer application, see the figure above for an example with an opto-coupler. Follow the country-specific safety requirements.



The transistors and the serial resistors on their collectors are located in the System Module (not in FSEB).

☞ If you use control outputs on the EACX-I port (D-Sub connector X4101), do not use the same control outputs on the screw terminal X4104.

RA22714EN01GLA0

138


Installing Flexi System External Alarm (FSEB) Installation Procedure (3/3) 9. Install the fire detector to the FSEB (optional). 10. Install the cover of the FSEB box and tighten the eight screws to 1.7 Nm. Install the cover 10


RA22714EN01GLA0

9. Install the fire detector to the FSEB (optional): a) Connect the fire detector to the FSEB using a four-wire cable. Two wires are needed for fire detector power supply and two for the fire detector alarm connection. b) Attach the four wires of the cable to the fire detector relay-base. c) Insert the other end of the four wire cable through one cable gland at the right half of the FSEB box. Tighten the cable gland nut. d) The cable must not move inside the gland. e) Route the cable and fix it with cable ties. The first fixing point must not be further away from the FSEB box than 0.5 m (1.6 ft). f)

Attach the wire marked with + from the fire detector to the leftmost or rightmost opening of the screw terminal X4114.

g) Attach the wire marked with - from the fire detector to one of the four middleopenings of the screw terminal X4114 marked with GND. h) Attach the fire detector alarm wires to one of the alarm inputs 'EXT_AL12 ... EXT_AL1'. 10. Install the cover of the FSEB box and tighten the eight screws to 1.7 Nm.

RA22714EN01GLA0

139


Installing Flexi System External Alarm (FSEB) Connecting external alarms cable • There are two options for external alarm cables in Flexi BTS: – Flexi System External Alarm Module (FSEB) external alarm cable – Flexi System Alarm cable (FSAA) • The FSEB external alarm cable is connected from the System Module to the FSEB. • The FSAA cable connects from the System Module directly to UltraSite, ExtraTalk, or other alarm systems. • The FSAA cable is used when an FSEB is not required.

• The FSAA cable is used when an FSEB is not required.

• The FSAA cable connects directly to UltraSite and ExtraTalk alarm cables with the Dconnector. • The FSAA cable can be connected to other alarm systems by cutting the Dconnector and connecting the wires to the terminals.


RA22714EN01GLA0

Steps: 1. Remove the connector seal from the external alarms connector in the System Module front panel. Store the seal for later use. The seal can be stored in the plinth. 2. Route the external alarms cable through the cable entry (stack, wall and pole installations). 3. Pull back the connector seal covering the external alarms cable connector. 4. Connect the cable to the external alarms connector. 5. Push the cable connector seal firmly in place. 6. Route and connect the other end of the external alarms cable to the external alarms control box or to the distribution frame. If connecting to an FSEB, connect the other end of the cable to the ESM connector in the FSEB. If connecting to an UltraSite or ExtraTalk alarm cable, connect the other end to the cable. 7. Make sure that all connector seals are firmly in place.

RA22714EN01GLA0

140


Installing Flexi System External Alarm (FSEB) Installing optional Flexi Mounting Auxiliary Brackets (FMAA) • The FMAA can be used with the following auxiliary units: • • •

Flexi System External Alarm (FSEB) Flexi System External OVP (FSEC) Location Measurement Unit (LMUB) Outdoor

1

4 3


1.

Remove the four connection pins from the casing on which the FMAA will be installed.

2.

Align the outer holes of each bracket with the connection pin holes.

3.

Use the M5 X 6 screws to mount each bracket to the casing.

4.

Mount the auxiliary unit on the brackets

4 3

RA22714EN01GLA0

Before you start Make sure the mains breaker is off. For FPMA installation locations in Flexi Multiradio BTS configurations..

RA22714EN01GLA0

141




RA22714EN01GLA0

RA22714EN01GLA0

142


Installing Flexi Power Module (FPMA) FPMA in stack, wall, and pole (1/3) • The Flexi Multiradio BTS uses 48 VDC power. • In a BTS site with AC feed only, a Flexi Power Module (FPMA) is required for converting the AC to DC before feeding the DC power to the System Module. • The Flexi Power Module (FPMA) consist of : • Mechanics • AC terminal • and four slots for AC/DC sub-module (FPAA) or battery sub-module (FPBA) Example of FPMA with 3 AC/DC sub-modules and 1 Flexi Power Battery

+ -

AC input cabling to FPMA


48VDC output to BTS

AC feed to FPAA (3pcs) RA22714EN01GLA0

RA22714EN01GLA0

143


Installing Flexi Power Module (FPMA) FPMA in stack, wall, and pole (2/3) • The following FPMA and FPAA/FPBA combinations are allowed: • Up to two FPMAs can be connected to one System Module • If two FPMAs are connected to the same System Module, double rubber boots (822862) are required for safety • Any combination of up to four FPAAs and FPBAs can be installed in one FPMA • To find the number of FPAAs required for a configuration, see the section Common cabinet configurations in the documents Creating Stack, Wall and Pole Configurations for Flexi Multiradio BTS GSM/EDGE. See also Creating FCIA configurations for Flexi Multiradio GSM/EDGE BTS and Creating FCOA configurations for Flexi Multiradio GSM/EDGE BTS. • If two FPMAs are connected to the same System Module and both FPMAs contain FPBAs, the current draw is distributed evenly among all FPBAs.


RA22714EN01GLA0

RA22714EN01GLA0

144


Installing Flexi Power Module (FPMA) FPMA in stack, wall, and pole (3/3) • The FPMA must be located close enough to the System Module so that the alarm cable and DC power cables reach the appropriate connectors without blocking access to other modules. • In stack, wall, and pole installations, the recommended location for the FPMA is below the System Module on the same plinth.

• By default, the DC output voltage of the FPMA is floating nominal 48 VDC, however, it can also be positive grounded as in the figure. • The maximum diameter of the AC power feed cable is 24 mm (0.9 in.)

Maximum sizes of conductors Rated connecting capacity

Value

Rigid (solid or stranded)

up to 16 mm2 (6 AWG)

Flexible


Flexible with ferrule (without plastic sleeve)


Flexible with ferrule (with plastic sleeve)


Flexible with TWIN ferrule

up to 6 mm2 (9 AWG)


RA22714EN01GLA0

RA22714EN01GLA0

145


Installing Flexi Power Module (FPMA) FPMA in stack, wall, and pole – Installation Procedure (1/5) 1. 1

2. 3. 4. 5.

2

6.

3

Install the Flexi Power Module (FPMA) and ground it. Loosen the two top screws and detach the bottom screw. Remove the ingress protection plate from the left-hand side of the FPMA. Pull out the AC terminal plate. Route the cable through the round hole in the top left corner of the ingress protection plate. Route the cable through the cable clamp on the AC terminal plate.

6

5


RA22714EN01GLA0

Before you start • Check that the mains breaker is off. • For FPMA installation locations in Flexi Multiradio BTS configurations, see Optional power modules (FPDA and FPMA) in Flexi Multiradio BTS configurations. Steps:

RA22714EN01GLA0

146


Installing Flexi Power Module (FPMA) FPMA in stack, wall, and pole – Installation Procedure (2/5) Single phase AC connection, 230 VAC

7.

Make the AC connection See the figures for AC connection alternatives Note: Danger of lethal voltages! Switch off the AC power breaker before connecting the AC cable.

Split Phase L1-L2 base voltage 100-120 V AC

3-phase delta connection, base voltage 100-120 V AC

3-phase star connection, 230 V AC NOTE:REMOVE BRIDGES

Note: The colours of the wires may vary depending on the country. For internal use only 147 © Nokia Siemens Networks

NOTE:REMOVE BRIDGES RA22714EN01GLA0

RA22714EN01GLA0

147


Installing Flexi Power Module (FPMA) FPMA in stack, wall, and pole – Installation Procedure (3/5)

10

8

8.

Push the AC terminal plate halfway back into its slot.

9.

Install the FPAA sub-modules required by your configuration.

9

The first or only FPAA must always be installed in the leftmost module slot. If there are empty slots, they must always be on the right.

8. 9.

Fix the FPAA screws. Connect the AC cable from the FPAA to the FPMA AC terminal plate.

10. If you are using battery backup, install the FPBA sub-modules required by your configuration. 11 12 For internal use only 148 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

148


Installing Flexi Power Module (FPMA) FPMA in stack, wall, and pole – Installation Procedure (4/5) 13. If alarms from the FPMA to the System Module are needed, connect the alarm cables.

13a

a) Remove the ingress protection from the alarm cable connectors in FPAA and FPBA.

13c

13b

b) Chain the sub-modules together with the alarm cable from left to right.

c) Connect the alarm cable from one of the sub-modules to the FPA connector on the System Module.

14. Connect the DC cables to all the sub-modules.

15. Push the AC terminal plate all the

14

way back into its slot. 15


RA22714EN01GLA0

RA22714EN01GLA0

149


Installing Flexi Power Module (FPMA) FPMA in stack, wall, and pole – Installation Procedure (5/5) 16. Reinsert the ingress protection plate with cables routed through it. 16

17. Fix the screw. 18. Install the cable entries. 19. Route the DC power feed cables through

17

the cable entries and connect them from the FPMA to the System Module.

20. Check that the cable connectors' seal caps are firmly in place.

21. Connect the mains power. 22. Power up the site. 23. Turn on the FPAA and FPBA by pushing

18

the switch.

24. Install the FPMA module front panel cover. 25. If FPBA(s) are used, shortly disconnect the AC mains power after commissioning. For internal use only 150 © Nokia Siemens Networks

RA22714EN01GLA0

Note : For step 23: Turn on the FPAA and FPBA by pushing the switch. Make sure that the FPAA LED is stable green and the FPBA LED is green and blinking slowly (charging). To maximise the FPBA life-time, the charging current is limited. Therefore, it can take up to 12 hours to fully charge an empty FPBA. For step 25: If FPBA(s) are used, shortly disconnect the AC mains power after commissioning. After the site is fully commissioned and integrated, disconnect the AC mains power for a short while to ensure that the FPMA is able to supply the site and that the 7995 MAINS BREAKDOWN WITH BATTERY BACK-UP alarm is raised on the BTS Manager.

RA22714EN01GLA0

150


Installing Flexi Power Module (FPMA) FPMA in Flexi Cabinet for Indoor (FCIA) • The following FPMA and FPAA/FPBA combinations are allowed: • Up to two FPMAs can be connected to one System Module • If two FPMAs are connected to the same System Module, double rubber boots (822862) are required for safety • Any combination of up to four FPAAs and FPBAs can be installed in one FPMA • To find the number of FPAAs required for a configuration, see the section Common cabinet configurations in the documents Creating FCIA configurations for Flexi Multiradio GSM/EDGE BTS . • The FPMA must be located close enough to the System Module so that the alarm cable and DC power cables reach the appropriate connectors without blocking access to other modules • In FCIA, the recommended location for the FPMA is next to the System Module in the rack.


RA22714EN01GLA0

RA22714EN01GLA0

151


Installing Flexi Power Module (FPMA) FPMA in Flexi Cabinet for Outdoor (FCOA) – Installation Procedure 1.

Remove the connection pins for the module casing.

2.

Remove the support plate behind the cage nuts.

3.

Detach the cage nuts from the module.

4.

Fix the cage nuts (from the module) on the rack on the left-hand side of the cabinet.

5. 6. 7.

Insert the module.

1 2 3

2

3

3

Fix with screws. Connect the mains breaker.

The sub-modules can be installed inside the FPMA before installing it into the cabinet.


RA22714EN01GLA0

Before you start Make sure the mains breaker is off. For FPMA installation locations in Flexi Multiradio BTS configurations, see Optional power modules (FPDA and FPMA) in Flexi Multiradio BTS configurations.

RA22714EN01GLA0

152


Installing Flexi Power Module (FPMA) FPMA in Flexi Cabinet for Indoor (FCIA) • The following FPMA and FPAA/FPBA combinations are allowed: • Up to two FPMAs can be connected to one System Module • If two FPMAs are connected to the same System Module, double rubber boots (822862) are required for safety • Any combination of up to four FPAAs and FPBAs can be installed in one FPMA • To find the number of FPAAs required for a configuration, see the section Common cabinet configurations in the documents Creating FCOA configurations for Flexi Multiradio GSM/EDGE BTS. • The FPMA must be located close enough to the System Module so that the alarm cable and DC power cables reach the appropriate connectors without blocking access to other modules • In FCIA, the recommended location for the FPMA is next to the System Module on the horizontal rack or on the vertical rack closest to the System Module.


RA22714EN01GLA0

RA22714EN01GLA0

153


Installing Flexi Power Module (FPMA) FPMA in Flexi Cabinet for Indoor (FCOA) – Installation Procedure (1/2) 1

1.

Remove the connection pins for the module casing.

2.

Remove the cable support plates from the casings.

3.

Remove unit fixing screws (tx25) and 10mm thick spacer plates beneath them.

4.

Remove gage nuts (4pcs) and thin support plate (2pcs).

5.

Detach the cage nuts and support plates behind them from the module.

6.

Remove the air separator plate.

2 2

3

3

3


RA22714EN01GLA0


RA22714EN01GLA0

154


Installing Flexi Power Module (FPMA) FPMA in Flexi Cabinet for Indoor (FCOA) – Installation Procedure (2/2) 7

8

7. Fix the cage nuts (from the module) on the rack on the left-hand side of the cabinet.

8. Insert the module. 9. Fix with screws and thick spacer plates.

10. Connect the mains power.


RA22714EN01GLA0


RA22714EN01GLA0

155


Installing Flexi Power Module (FPMA) Connecting Power Module alarm cables • The Power Module (FPMA) alarm cables are connected between Power Module submodules.

Procedure installation 1. 2. 3. 4.

Remove the IP seals from the alarm cable connectors in the FPAA and FPBA. Chain the sub-modules together with the alarm cable from left to right. Connect the alarm cable from one of the sub-modules to the System Module. Make sure that all connector seals are firmly in place.


RA22714EN01GLA0

Notes: •

Incorrect cables and seals may not provide secured weather protection. In outdoor installations, including the outdoor cabinet, use only tested IP65 class outdoor cables with seals provided by Nokia Siemens Networks. This is also recommended for indoor installations.

•

Store all unused seals for later use.

•

Risk of damage to equipment. Connector seals or boots must be installed at all times, whether the site is active or not.

RA22714EN01GLA0

156




RA22714EN01GLA0

RA22714EN01GLA0

157


Installing Flexi Power DC/DC Module 24V (FPDA) Overview • The FPDA is an isolated 2U-high DC/DC Power Module that converts nominal 24 V DC input voltage to 48 V DC nominal output voltage and 2 kW power.

• When the BTS power load is more than 2 kW, multiple FPDAs can be installed in parallel.

• When FPDAs are used in parallel, a maximum of two DC cables can be installed together at each output terminal. This limitation is due to: • The output current from the FPDA where all three are combined would exceed the safety limits for the thickness of the DC cables provided in the delivery. • The safety rubber boots provided in the delivery can accommodate up to two DC cables per terminal. • The DC output terminal bolt length can accommodate up to two DC cables per terminal


RA22714EN01GLA0


RA22714EN01GLA0

158


Installing Flexi Power DC/DC Module 24V (FPDA) FPDA provisioning based on number of FPDAs (1/3) • examples of FPDA provisioning based on the number of FPDAs Circuit Breaker

Circuit Breaker

Circuit Breaker

24 VDC

24 VDC

24 VDC

48 VDC

FPDA

with one FPDA System Module with two FPDAs

FPDA

48 VDC

FPDA

48 VDC

System Module with three FPDAs two

Circuit Breaker

Circuit Breaker

Circuit Breaker

24 VDC

24 VDC

24 VDC


48 VDC

FPDA

FPDA

System Module

system modules (sample 1)

48 VDC

FPDA

48 VDC

the power draw from the System module to the single FPDA cannot exceed 2kW.

System Module

RA22714EN01GLA0

Note: •When FPDAs are installed in parallel, the DC output cables should be installed together at the FPDA closest to the System module. •Two additional 4 AWG (25 mm2) cable lugs are required for each additional FPDA used in parallel. These lugs are not included in the delivery and must be sourced locally. •When FPDAs are installed in parallel and a power failure occurs in a DC line, the input voltage to the System module will likely drop below the acceptable level. If an FPDA is overloaded with power, then the unit will shut itself down. •In the example in Figure FPDA provisioning for configurations with three FPDAs and two system modules (sample 1), the power draw from the System module to the single FPDA cannot exceed 2kW.

RA22714EN01GLA0

159


Installing Flexi Power DC/DC Module 24V (FPDA) FPDA provisioning based on number of FPDAs (2/3) • examples of FPDA provisioning based on the number of FPDAs … cont’d Circuit Breaker

24 VDC

48 VDC

FPDA

System Module

48 VDC Circuit Breaker

24 VDC

with three FPDAs two

system modules (sample 2)

FPDA 48 VDC

Circuit Breaker

24 VDC

FPDA

48 VDC

System Module with three FPDAs one

Circuit Breaker

Circuit Breaker

Circuit Breaker

24 VDC

24 VDC

24 VDC


48 VDC

FPDA

system module (sample 3) System Module

FPDA

FPDA

48 VDC

RA22714EN01GLA0

Note: •In Figure provisioning for configurations with three FPDAs and one system module (sample 3), FPDA provisioning requires four pairs of double rubber boots (822862) for safety. The standard delivery for this configuration only includes three pairs of double roots. •An extra pair must be ordered as a spare part for combining the DC cables at each System Module input terminal.

RA22714EN01GLA0

160


Installing Flexi Power DC/DC Module 24V (FPDA) FPDA provisioning based on number of FPDAs (3/3) • examples of FPDA provisioning based on the number of FPDAs … cont’d Circuit Breaker

Circuit Breaker

Circuit Breaker

Circuit Breaker

24 VDC

FPDA 48 VDC

24 VDC

24 VDC

FPDA

48 VDC

with four FPDAs two system modules

System Module

FPDA 48 VDC

24 VDC

FPDA

48 VDC

System Module

The FPDA is delivered with two sets of rubber boots:

• one set accommodates cable thickness of 35-50 mm2 (2 to 1/0 AWG) for 24 V DC input. Required cable thickness depends on the distance and voltage drop from the external 24 V DC power supply.

• the other set accommodates up to two 25 mm2 (4 AWG) cables per terminal for 48 V DC output to the System module. These boots can be used for single or dual DC cables at each power terminal. Dual usage is required for pairing (chaining) cables when two FPDA modules are used in parallel as shown in figure Parallel FPDAs with paired (chained) DC cables and boots. For internal use only 161 © Nokia Siemens Networks

RA22714EN01GLA0

Note:

RA22714EN01GLA0

161


Installing Flexi Power DC/DC Module 24V (FPDA) Installation procedure (1/3)

3

2

1.

Install the FPDA and (in cabinet installation) fix the module to the cabinet with screws.

2.

Attach the cable entries using two screws (in stack, wall and pole installation).

3.

Make sure that the power switch on the front panel is in the standby position.

4.

Connect the grounding cable to the plinth (in stack, wall and pole installation).

4


RA22714EN01GLA0

Note:

RA22714EN01GLA0

162


Installing Flexi Power DC/DC Module 24V (FPDA) Installation procedure (2/3)

7 5

5.

Remove the bolts and washers from the DC output terminals.

6.

Insert the rubber boots to the DC output cables.

7.

Route the DC output cables through the cable entry (in stack, wall and pole installation).

8.

Connect the V48N- cable to the minus terminal and V48RTN+ cable to the plus terminal in the FPDA module.

9.

Tighten the bolts to 10.0 - 14.0 Nm (7.0 - 9.8 ft -lb) Nm.

6

8

10

10. Pull the rubber boots over the DC output terminals.

11. Connect the DC output cables to the System Module. For internal use only 163 © Nokia Siemens Networks

RA22714EN01GLA0

Note: For no: 6 Insert the rubber boots to the DC output cables. If the cable is 50 mm2, cut the rubber boot to fit the cable. If two FPDAs are used in parallel, cut the sealed hole on the DC output boots. For no: 7 7 Route the DC output cables through the cable entry (in stack, wall and pole installation). Use the top right entry hole for the V48N- cable and bottom right entry hole for the V48RTN+ cable. For no: 11 Connect the DC output cables to the System Module. Note that there is a risk of short circuit. Connect the power cable as instructed.

RA22714EN01GLA0

163


Installing Flexi Power DC/DC Module 24V (FPDA) Installation procedure (3/3) 12. Remove one of the alarm connector seals on the front panel of the FPDA and connect the alarm cable.

13. Check that the power switch on the front panel of the FPDA is still in the stand-by position.

14. Make sure that the 24 V DC supply for the FPDA is de-energised and connect the DC input cables similarly as the DC output cables.

15. 15 Connect the AC mains power for the 24 V DC supply system.

16. Connect the 24 V DC supply (and the battery circuit breaker if the 24 V DC supply system is a battery back-up system). Make sure the LED is yellow.

17. Switch on the power by pushing the power switch on the front panel of the FPDA. Make sure the LED is green.

18. Make sure that the unused connectors are covered with seal caps. 19. Install the module front cover (in stack, wall and pole installation). For internal use only 164 © Nokia Siemens Networks

RA22714EN01GLA0

Note: For 12 Remove one of the alarm connector seals on the front panel of the FPDA and connect the alarm cable. Make sure that you are inserting the cable connector as instructed in the figure. For no: 14 Make sure that the 24 V DC supply for the FPDA is de-energised and connect the DC input cables similarly as the DC output cables. Connect the minus wire to the minus terminal and the plus wire to the plus terminal. Note that the DC input cables are not included in the delivery. The length and thicknessof the DC input cables must be defined based on the distance to the 24 V DC power source. The maximum thickness of a DC input cable that can be installed to the FPDA is 50 mm²/AWG 1/0

RA22714EN01GLA0

164


Installing Flexi Power DC/DC Module 24V (FPDA) Optional power modules combination (FPDA and FPMA) - Overview • Optional power modules used for AC or 24 VDC power supply are : • Flexi Power DC/DC Module 24 V (FPDA) and • Flexi Power Module (FPMA) with AC/DC 230 V Sub-modules (FPAA) Number of power modules needed Configuration

Number of FPDAs

1+1+1 up to 6+6+6 2UD configuration with one RF Module

1

Number of FPMAs 1 FPMA with 2 FPAA

• The FPMA must be located close enough to the System Module so that the alarm cable and DC power cables reach the appropriate connectors, as recommendation: • • •

In stack, wall, and pole installations  below the System Module on the same plinth. In FCIA  next to the System Module in the rack. In FCOA  next to the System Module on the horizontal rack or on the vertical rack closest to the System Module

• The FPDA(s) must be located close enough to the System Module so that the alarm cable reaches the appropriate connectors without blocking access to other modules, as recommendation: For stack configurations  on top of the stack. For pole and wall configurations  on the same plinth or next plinth as the System Module. For FCIA configurations  directly above the top module in the BCF. For FCOA configurations  same as the FCIA on the horizontal rack or on the vertical rack closest to For internal use theonlySystem module.

• • • •

165


RA22714EN01GLA0

RA22714EN01GLA0

165


Installing Flexi Power DC/DC Module 24V (FPDA) Optional power modules combination (FPDA and FPMA) Installation location for 1+1+1 up to 6+6+6 2UD with one RF Module 1+1+1 upto 6+6+6 2UD configuration in a stack, with FPDA


1+1+1 upto 6+6+6 2UD configuration in a stack, with FPMA

RA22714EN01GLA0

RA22714EN01GLA0

166


Installing Flexi Power DC/DC Module 24V (FPDA) Optional power modules combination (FPDA and FPMA) Installation location for 1+1+1 up to 6+6+6 2UD with one RF Module 1+1+1 upto 6+6+6 2UD configuration on a wall, with FPDA


1+1+1 upto 6+6+6 2UD configuration on a wall, with FPMA

RA22714EN01GLA0

RA22714EN01GLA0

167


Installing Flexi Power DC/DC Module 24V (FPDA) Optional power modules combination (FPDA and FPMA) Installation location for 1+1+1 up to 6+6+6 2UD with one RF Module 1+1+1 upto 6+6+6 2UD configuration on a pole, with FPDA


1+1+1 upto 6+6+6 2UD configuration on a pole, with FPMA

RA22714EN01GLA0

RA22714EN01GLA0

168


Installing Flexi Power DC/DC Module 24V (FPDA) Optional power modules combination (FPDA and FPMA) Installation location for 1+1+1 up to 6+6+6 2UD with one RF Module 1+1+1 up to 6+6+6 2UDconfiguration in FCIA, with FPMA


1+1+1 up to 6+6+6 2UD configuration in FCIA, with FPDA

RA22714EN01GLA0

RA22714EN01GLA0

169


Installing Flexi Power DC/DC Module 24V (FPDA) Optional power modules combination (FPDA and FPMA) Installation location for 1+1+1 up to 6+6+6 2UD with one RF Module 1+1+1 up to 6+6+6 2UD configuration in FCOA, with FPDA


1+1+1 up to 6+6+6 2UD configuration in FCOA, with FPMA

RA22714EN01GLA0

RA22714EN01GLA0

170




RA22714EN01GLA0

RA22714EN01GLA0

171


Installing Flexi Power Rectifier (FPRA) Overview

• The FPRA also includes a Power Distribution Assembly (PDA), which contains a fully integrated battery protection LVD, load/battery circuit breakers. • Alarm signals to the BTS Alarm interface are connected to the PDA unit via a pull out Alarm Interface Card. FPRA Power Distribution Assembly unit


FPRA Alarm Interface card

RA22714EN01GLA0

RA22714EN01GLA0

172


Installing Flexi Power Rectifier (FPRA) Principles for installing FPRx in Flexi Multiradio BTS configurations (1/2) • The FPRx can be installed anywhere in a stack or cabinet provided that the 2 m (6.6 in.) alarm cable can be connected between the FPRx and System Module (System Module).

• In indoor cabinet (FCIA) installations, the recommended location for FPRx is: • without batteries  at the top of the cabinet, near the cabinet roof. • with batteries  near the bottom of the cabinet, in the next available rack space above the batteries.

• In outdoor cabinet (FCOA) installations, the recommended location for FPRx is: • without batteries: – If batteries are not used, only the FPRB or FPRC can be used in FCOA – If the System Module (ESMB/C) is in the top vertical rack, install the FPRB/FPRC module on the lower vertical rack

– If the System Module is in the horizontal rack, install the module in the top vertical rack.

• with batteries: – Site Support Module (FCSA) is installed inside the FCOA cabinet For internal use only 173 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

173


Installing Flexi Power Rectifier (FPRA) Principles for installing FPRx in Flexi Multiradio BTS configurations (2/2)

• In Stack installations, the recommended location for FPRx is: • In outdoor  only the FPRC module can be used because of WDR requirements. Flexi front and back covers must be used.

• For indoor  any FPRx can be used. • Location is the bottom of the stack. • This allows for easier future expansion because the top sector can be expanded without the Upgrade RF Cable Kit (EUCA).

• In wall and pole installations, the recommended location for FPRx is: • Only the FPRC is used in wall and pole installations. Flexi front and back covers must be used.

• The recommended location is either on the same plinth as the System Module or on an adjacent plinth


RA22714EN01GLA0

RA22714EN01GLA0

174


Installing Flexi Power Rectifier (FPRA) Connecting FPRA alarms cables • FPRA delivery does not include any alarm cables. • The required cables are either supplied with the interconnecting units (Flexi System External Alarm (FSEB) and/or Flexi Cabinet Site Support Module (FCSA)) or must be ordered separately depending upon the configuration. • When using Flexi Power Rectifier (FPRA) with Flexi Cabinet Site Support Module (FCSA) in an outdoor application, there are three different cabling configurations for Flexi Multiradio BTS which can be used depending upon the number of alarms signals required by the user FPRA front view


RA22714EN01GLA0

RA22714EN01GLA0

175


Installing Flexi Power Rectifier (FPRA) Connecting FPRA alarms - Overview • The PDA supplies six isolated and floating EAC alarms to the BTS, which are summarised in the table below. EAC alarm Main 1 Main 2

Description (see Tip below the table) Mains phase failure indicates any single phase voltage of the 3-phase FPRA power source configuration that is below 85 V AC

Main 3 Critical

• Battery low voltage • PDA controller fail

• DC distribution failure (e.g. Circuit Breaker tripped)

Major

• Battery test failure • Rectifier fail • High float voltage

• Rectifier Fan Failure • Input voltage too high or too low (rectifier shutdown) • Surge Protection Device failed

Minor

• Battery temperature High/Low • Rectifier temperature High • Rectifier over current

• Extended mains voltage range • Low mains voltage range

Ext Alarm In

Remote-start for Battery Test

☞ The settings listed in the above table are the factory-default alarm settings. The user can re-configure the alarm settings as required.


RA22714EN01GLA0

RA22714EN01GLA0

176


Installing Flexi Power Rectifier (FPRA) Connecting FPRA alarms - Connection Procedure Detaching the Alarm Interface card

1. 2. 3. 4.

5. 6. 7. 8.

Cut the cable screening back to approximately 20 mm Connect the screening to position ‘A’ Push the drawer back into its slot horizontally until the drawer pin matches the internal connector of the PDA and secure the two thumbscrews


Detach the Alarm Interface Card from the PDA To insert the cable, puncture the waterproof seal marked ‘Alarm In’ Feed the bare end of the cable through the hole. Strip back the outer sleeve of the cable

Connecting the FPRA alarm cable

RA22714EN01GLA0

RA22714EN01GLA0

177


Installing Flexi Power Rectifier (FPRA) Connecting FPRA to System Module EAC connector •

ECBA Cable 471464A (separate sales item) is needed 471464A

System Module

FPRA Flying lead

RJ45 Connector

EAC connections

FPRA J11 pin number

FSAA cable Name

Color

EAC signal

1

ALARM IN (-)

BLACK

EXT_CO1

2

ALARM IN (+)

WHITE/BLACK

+5V

3

ALARM_COM

WHITE/GREEN

GND

4

MAINS 1

GREEN

EXT_AL1

5

ALARM_COM

WHITE/BLUE

GND

6

MAINS 2

BLUE

EXT_AL2

7

ALARM_COM

WHITE/VIOLET

GND

8

MAINS 3

VIOLET

EXT_AL3

9

ALARM_COM

WHITE/GREY

GND

10

CRITICAL

GREY

EXT_AL4

11

ALARM_COM

BLACK/RED

GND

12

MAJOR

PINK

EXT_AL5

13

ALARM_COM

BLACK/GREEN

GND

MINOR

LIGHT GREEN

EXT_AL6

For internal 14 use only 178 © Nokia Siemens Networks

RA22714EN01GLA0

Steps: 1. Cut the 37 way D-type connector from cable assembly 471628A, leaving the MDR- 36 connector intact. 2. Insert the cable into the alarm module as described in Connecting Flexi Power Rectifier (FPRA) alarm cable. 3. Connect the twisted pair cables to the J11 connector 4. Secure the alarm cable to the drawer sidewall with a cable tie. 5. Push the drawer back into its slot horizontally until the drawer pin matches the internal connector of the PDA and secure the two thumbscrews. 6. Connect the MDR36 connector to the EAC connector of the System Module.

RA22714EN01GLA0

178


Installing Flexi Power Rectifier (FPRA) Connecting FPRA to System Module FPA connector •

ECBA Cable 471464A (separate sales item) is needed 471464A

System Module

FPRA Flying lead

RJ45 Connector

FPA connections

FPRA J11 pin number

Cable 471464A Name

RJ45 wire number

FPA signal

4

MAINS 1

4

7995

6

MAINS 2

3

7995

8

MAINS 3

2

7995

10

CRITICAL

1

7612

12

MAJOR

5

7613

14

MINOR

6

7614

3

COM

7

GND


RA22714EN01GLA0

Steps: 1. Cut the 9 way D Type connector from cable assembly 471464A. 2. Use a DVM to find which wire is connected to Pins 1-8 on the RJ45 connector, because cable assembly 471464A is not color-coded. 3. Connect the wires to the J11connector 4. Make sure that any unused wires are insulated and sleeved. 5. Secure the alarm cable to the drawer sidewall with a cable tie. 6. Push the drawer back into its slot horizontally until the drawer pin matches the internal connector of the PDA and secure the two thumbscrews. 7. Connect the RJ45 connector to the FPA connector of the Flexi System Module. Note that FPRA Alarm outputs must be configured for “active closed” (closed on Alarm) when using FPA Alarm Input. See the FPRA User Manual for details of alarm settings.

RA22714EN01GLA0

179


Installing Flexi Power Rectifier (FPRA) Connecting FPRA to Flexi System External Alarm (FSEB) •

994945 (supplied with FSEB) & 471628A (separate sales item) are needed Connecting FPRA to Flexi System External Alarm (FSEB)

FSEB connections FPRA


FSEB

Description

J11 pin

Wire colour

Conne ctor

Pin num ber

EAC signal

ALARM IN (-)

1

BLACK

X4104

1

EXT_CO1

ALARM IN (+)

2

WHITE/ BLACK

X4105

1

+5V

ALARM_COM

3

WHITE/ GREEN

X4107

1

GND

MAINS 1

4

GREEN

X4106

1

EXT_AL1

MAINS 2

6

BLUE

X4106

2

EXT_AL2

MAINS 3

8

VIOLET

X4106

3

EXT_AL3

CRITICAL

10

GREY

X4106

4

EXT_AL4

MAJOR

12

PINK

X4106

5

EXT_AL5

MINOR

14

LIGHT GREEN

X4106

6

EXT_AL6

RA22714EN01GLA0

Steps: 1. Connect alarm cable 994945 from the EAC connector on the System Module to the ESM connector of the FSEB. 2. Cut both connectors from cable assembly 471628A leaving just the cable itself. 3. Insert one end of the cable into the Alarm Interface Card as described in Connecting Flexi Power Rectifier (FPRA) alarm cable. 4. Connect the wires between the J11 connector of the Alarm Interface Card and the alarms connector located in the FSEB box 5. Secure the alarm cable to the side wall with a cable tie. 6. Push the drawer back into its slot horizontally until the drawer pin matches the internal connector of the PDA and secure the two thumbscrews.

RA22714EN01GLA0

180


Installing Flexi Power Rectifier (FPRA) Connecting 3 FPRA alarms and 4 FCSA alarms •

994957 (supplied with FCSA), 994945 (supplied with FSEB) & 994157 (separate sales item) are needed

Connecting 3 FPRA alarms and 4 FCSA alarms

Cable 994157 connections FPRx


Cable 994157

J11 pin number

Name

Colour

FCSA alarm

4

MAINS 1

WHITE/GREEN

MAINS #1

6

MAINS 2

WHITE/BROWN

MAINS #2

8

MAINS 3

WHITE/GREY

MAINS #3

3

COM

ORANGE/WHITE

GND

RA22714EN01GLA0

Steps: 1. Connect alarm cable 994945 from the EAC connector on the System Module to the ESM connector of the FSEB. 2. Connect alarm cable 994957 from the Ext Alarms Output connector on the FCSA control card to the external alarms connector located in the FSEB box. 3. Cut one of the 9-way D-Type connector from cable assembly 994157, leaving the other end intact. 4. Insert the cable into the Alarm module as described in Connecting Flexi Power Rectifier (FPRA) alarm cable. 5. Connect the cables to the J11 connector as shown in the table below. 6. Secure the alarm cable to the drawer side wall with a cable tie. 7. Push the drawer back into its slot horizontally until the drawer pin matches the internal connector of the PDA and secure the two thumbscrews 8. Connect the 9-way D-type connector to the MIBBU connector of the FCSA Control Card.

RA22714EN01GLA0

181


Installing Flexi Power Rectifier (FPRA) Connecting 6 FPRA alarms and 4 FCSA alarms using ECBA cable

•

994957 (supplied with FCSA), 994945 (supplied with FSEB) & 471464A (ECBA cable, separate sales item) are needed Connecting 6 FPRA alarms and 4 FCSA alarms using ECBA cable

Cable 471464A connections FPRx J11 pin number


Cable 471464A Name

RJ45 wire number

FPA alarm

4

MAINS 1

4

7995

6

MAINS 2

3

7995

8

MAINS 3

2

7995

10

CRITICAL

1

7612

12

MAJOR

5

7613

14

MINOR

6

7614

3

COM

7

GND

RA22714EN01GLA0

Steps: 1. Connect alarm cable 994945 from the EAC connector on the System Module to the ESM connector of the FSEB. 2. Connect alarm cable 994957 from the Ext Alarms Output connector on the FCSA control card to the external alarms connector located in the FSEB box. 3. Cut the 9-way D Type connector from cable assembly 471464A, leaving the RJ45 end intact. 4. Use a DVM to find which wire is connected to Pins 1-8 on the RJ45 connector, because cable assembly 471464A is not color-coded. 5. Insert the cable into the Alarm module as described in Connecting Flexi Power Rectifier (FPRA) alarm cable. 6. Connect the cables to the J11 connector 7. Secure the alarm cable to the drawer side wall with a cable tie. 8. Push the drawer back into its slot horizontally until the drawer pin matches the internal connector of the PDA and secure the two thumbscrews. Note that FPRA Alarm outputs must be configured for “active closed” (closed on Alarm) when using FPA Alarm Input.

RA22714EN01GLA0

182


Installing Flexi Power Rectifier (FPRA) Connecting 6 FPRA alarms and 4 FCSA alarms •

994957 (supplied with FCSA), 994945 (supplied with FSEB) & 995239 (supplied with FCSA) are needed

Connecting 6 FPRA alarms and 4 FCSA alarms

FSEB connections FPRA


FSEB

Description

J11 pin

Wire colour

Conne ctor

Pin num ber

EAC signal

ALARM IN (-)

1

BLACK

X4104

1

EXT_CO1

ALARM IN (+)

2

WHITE/ BLACK

X4105

1

+5V

ALARM_COM

3

WHITE/ GREEN

X4107

1

GND

MAINS 1

4

GREEN

X4106

1

EXT_AL1

MAINS 2

6

BLUE

X4106

2

EXT_AL2

MAINS 3

8

VIOLET

X4106

3

EXT_AL3

CRITICAL

10

GREY

X4106

4

EXT_AL4

MAJOR

12

PINK

X4106

5

EXT_AL5

MINOR

14

LIGHT GREEN

X4106

6

EXT_AL6

RA22714EN01GLA0

Steps: 1. Connect alarm cable 994945 from the EAC connector on the System Module to the ESM connector of the FSEB. 2. Connect alarm cable 994957 from the Ext Alarms Output connector on the FCSA control card to the external alarms connector located in the FSEB box. 3. Cut the 9-way D-Type connector from cable assembly 995239, leaving just the cable itself. 4. Insert one end of the cable into the Alarm Interface Card as described in Connecting Flexi Power Rectifier (FPRA) alarm cable. 5. Connect the wires between the J11 connector of the Alarm Interface Card and the alarms connector located in the FSEB box 6. Secure the alarm cable to the drawer side wall with a cable tie. 7. Push the drawer back into its slot horizontally until the drawer pin matches the internal connector of the PDA and secure the two thumbscrews.

RA22714EN01GLA0

183




RA22714EN01GLA0

RA22714EN01GLA0

184


Flexi Multiradio BTS GSM/EDGE Installation Cabling Principles for Flexi Multiradio BTS GSM/EDGE Installation


RA22714EN01GLA0

RA22714EN01GLA0

185


Cabling principles in stack, wall, and pole installation (1/2) • Cables are routed along the sides of the modules. Excess cabling should be tied •

• • •

to clamps. In stack installations, cables are routed out both the left and right cable entries.. • All cables except the optical cables can be routed in either direction as long as they do not violate the bending diameter or block access to other used connectors. • The optical cable must always be routed to the left. It is also recommended to route the internal power cable in the same path as the optical cable for each module. • Antenna jumper cables can be routed out the left side, right side, or both sides. However, access to the optical and internal power cables during maintenance and expansion is easier when all antenna jumper cables are routed to the right. Internal cable entries are not typically used with Flexi Multiradio BTS. When preparing the external cable entries, cut a slit in the cable entry for routing the cables. In wall and pole installation, cables should be routed through the bottom cable entry whenever possible.


RA22714EN01GLA0

RA22714EN01GLA0

186


Cabling principles in stack, wall, and pole installation (2/2) Recommended cable routing principles in stack installation

Cable entry

Cables

External cable entries (right side)

• • • • • • • • •

External 48 V DC power cables (if EAC connector is not used) Grounding cables Optical cables with FIQA and FIYA (OPT) Optional cables: External alarm and control (EAC) Synchronisation (SYNC OUT, SYNC IN) Q1 interface (Q1) Location management unit (LMU)

External cable entries (left side)

• • • • • • • •

Internal power cables (PWR) External 24 V DC power cables External 48 V DC power cables (If EAC connector is used) Optical cables (OPT) External AC power cables Flexi power alarm cable (FPA) Grounding cables

Antenna jumper cables (ANT), RF cables (RxO), and transmission cables (FIxx) can be routed out either side of the module, depending on the location of the interface with respect to the cabinet For internal use only 187 © Nokia Siemens Networks

Note: In large configurations, mark cables for identification during maintenance.

RA22714EN01GLA0

RA22714EN01GLA0

187


Optional cable tunnels in stack, wall, and pole installation • The optional cable tunnels can be used to hide excess cabling on the side of stack or pole configurations. Cable tunnels are not required for weather protection. • Follow the below listed principles for the cable tunnels to fit properly: • Route the external cables on the right side of the BTS, and tie all cabling in between the top and bottom square holes on the support plates. • Route the internal cables on the left side of the BTS, and tie all side cabling as follows, using the square holes on the support plates as guides: • For vertical routing, tie the cables in between the beginning of the front hole and beginning of the rear hole. • For horizontal routing, tie the cables in between the top and bottom square holes. • Do not route internal cables through the back. • Remove the ears from cable entries before installation For internal use only 188 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

188


Internal power cabling principles for System Module (ESMB/C) • The following main principles for internal power cabling apply to RF Module (FXxx). • For stack and cabinet configurations, RF Modules can be numbered 1 to 4 from bottom to top. The power connection ports used on the System Module (ESMB/C) should match the RF Modules numbering. • In wall configurations, numbering can be from 1 to 4 from bottom to top, with the lower number for each plinth corresponding to the RF Module closest to the wall (the RF Module connected directly to the plinth). • In pole configurations, the RF Module closest to the System Module should correspond with port 1 for PWR on the System Module. • Numbering applies to optical cables and any numbering order can be followed. • Also, it is recommended that optical and power cable numbering should match for each RF Module, when the RF Module is powered by the System Module.


RA22714EN01GLA0

RA22714EN01GLA0

189


Bending Diameter for Cables for Flexi Multiradio BTS GSM/EDGE • The table below shows the minimum bending diameter of Flexi Multiradio BTS cables. • Static bending diameter refers to the allowed bend while the cable is fixed (for example, when the cable is tied to the side of the cabinet). • Dynamic bending diameter refers to the allowed bend while the cable is in motion (for example while routing the cable through the cable entry). Bending diameter of Flexi Multiradio BTS cables Cable Cable name Power cable

Cable Code 995281

Optical cables EMCA LMP cable Sync cable for Flexi Sync cable for Ultra-Site Sync LMU cable Q1 cable MIBBU EPA alarm cable Clock test cable Transmission cable


471370 471371 471372 471377 471384 471464 471521

Static bending diameter 117 mm (4.6 in.)

Dynamic bending diameter 170 mm (6.7 in.)

140 mm (5.6 in.)

140 mm (5.6 in.)

40 mm (1.6 in.)

45 mm (1.8 in.)

RA22714EN01GLA0

RA22714EN01GLA0

190




RA22714EN01GLA0

RA22714EN01GLA0

191


Flexi Multiradio BTS GSM/EDGE Installation Installation tools and torque values for Flexi Multiradio BTS GSM/EDGE


RA22714EN01GLA0

RA22714EN01GLA0

192


Installation Tools for Flexi Multiradio BTS GSM/EDGE (1/4) • This list provides a reference for installation tools required for all Flexi Multiradio BTS installation options. • These options are stack, wall, pole, Flexi Cabinet for Indoor (FCIA), Flexi Cabinet for Outdoor (FCOA), feederless sites, and installation in legacy and 3rd party cabinets. Installation tools

Usage

ESD wrist strap and cable

Module/sub-module installation

TORX screwdriver set: T10, T20, T25, T45

• Installing modules (T25) • Installing casing kits (T25) • Module grounding (T25) • FCIA/FCOA/FCFA/FCSA/FMFA mechanics (T25) • Installing sub-modules (T20) • Fan plate assembly (T20) • Anchoring EMIA standoff casing and EMIB rack plinth (T45)

• FCIA site grounding (T45) • Isolating cable clamps (T10) • EMIA or EMIB door alarm kit (T10) For internal use only 193 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

193


Installation Tools for Flexi Multiradio BTS GSM/EDGE (2/4) Installation tools

Usage

Socket or open-ended spanner (wrench) set: 8 mm, 13 mm, 17 mm, 19 mm Torque wrench is recommended for fastening the DC input lug.

Folding knife

Adjustable wrench Side cutters

• • • • • • • • •

DC power terminal nuts (17 mm) Plinth site grounding (13 mm) FCOA site grounding (13 mm, 8 mm) Anchoring cabinets/plinths (19 mm) Unpacking Routing cables through cable entries Preparing power and ground cables General installation tool Cutting tie wraps, general installation tool

Crimping tool for 16 mm2 (6 AWG), 25 mm2 (4 AWG), 35 mm2 (2 AWG), or 50 mm2 (1/0 AWG) cable lugs

• Grounding and DC power input cables

Torque wrench (7/16 in.)

• RS Torque wrench 25 Nm, 27/32 mm (CS77564.20) • RS Torque wrench 1.7 Nm, 19 mm (CS77507.30) • Connecting antenna cables to FXxx

Torque wrench for antenna cables (size depends on antenna jumper/feeder cable size and manufacturer) For internal use only 194 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

194



Usage

Cable ties

Routing cables

Tape measure

General installation tool

Flashlight, pocket lamp or torch


Drill with bit set: For EMIA: 10 mm (3/8 in.) - 13 mm (1/2 in.) For EMIB: 5 mm (3/16 in), 6 mm (7/32 in), 10 mm (3/8 in.), 13 mm (1/2 in), 64 mm (2 1/2 in.), Bi-metal hole saw

• • • •

Marker, pen, or comparable tool


Anchoring cabinets/plinths (12 mm) EMIB rack plinth rivet holes (5 mm) EMIB top support C-plate fixing holes (6 mm) EMIA/EMIB Citytalk cabinet bottom plate water holes (13 mm) • Grommet hole drilling (64 mm, Bi-metal hole saw)

Pliers


Level


Flathead screwdriver

FPMA AC power terminals

Allen (Hexagon) keys: 4 mm (5/32 in.), 5 mm (3/16 in.), 6 mm (7/32 in.), 8 mm (5/16 in.)

• VMPB/FPKA pole mounting kit (8 mm) • EMIA or EMIB installation (4 mm, 5 mm, 6 mm) • Feederless sites (grounding kit) (5 mm)


RA22714EN01GLA0

RA22714EN01GLA0

195



Usage

Thread locking compound (medium strength, non permanent), for example Loctite 242 or equivalent

Installation on a pole or wall FMSA

Vacuum cleaner or broom with dust pan

EMIA or EMIB installation

Hand saw

Feederless sites

Heat gun for cable shrinking sleeves

Feederless sites

Lint-free swabs

Cleaning the optical connectors

99% alcohol

Cleaning the optical connectors

Weatherproof protection tape

Flexbus Jumper Cable and Outdoor Flexbus cable connection


RA22714EN01GLA0

RA22714EN01GLA0

196


Torque Values for Flexi Multiradio BTS GSM/EDGE (1/2) • Nokia Siemens Networks strongly recommends that you tighten to the following torque values. • Use these values unless stated otherwise. Torque wrench

Torque values for the BTS Size

Type

Usage

Torque

M3

Screw, TORX pan head

EMIA and EMIB

0.7 - 1.0 Nm (0.52 -0.74 ft-lb)

M4

Screw, TORX cylinder head

FCSA and FCFA fans

1.2 - 1.6 Nm (0.9 - 1.2 ftlb)

M4

Screw, TORX pan head or thumb (knurled head)

• FIxx installation • ESMB/C, FXxx, and FPDA

2.7-3.3 Nm (1.99-2.43 ftlb)

fanplate assembly

• FMAA M5

Nut, Hex

FCOA site grounding

3.0 Nm (2.21 ft-lb)

M6

Screw, Allen or TORX head

• EMIA and EMIB • FMAA

4.2-5.8 Nm (3.1-4.28 ft-lb)


RA22714EN01GLA0

RA22714EN01GLA0

197


Torque Values for Flexi Multiradio BTS GSM/EDGE (2/2) Torque values for the BTS …cont’d Size

Type

Usage

Torque

M8

Screw, TORX or hex head

FCIA/EMIA/EMIB/plinth site grounding

8.0-10.0 Nm (5.9-7.37 ftlb)

M8

Nut, Hex

FCOA site grounding

5.0 Nm (3.68 ft-lb)

M8

Screw, hex head

Plinth adapter mechanics

10.0 Nm (7.37 ft-lb)

M8

Screw, hex head

Attaching FMFA to FPKA

20.0 Nm (14.74 ft-lb)

M10

Nut, Hex

ESMB/C, FPDA and EOCA DCpower terminals

10.0 - 14.0 Nm (7.0 - 9.8 ft -lb)

M10

Bolt, Allen head

VMPB/FPKA/FMFA pole mounting kits

30.0 Nm (22.9 ft-lb)

M12 (15/32 in.)

Anchoring bolts

Anchoring FCIA/FCOA/FMFA to floor (not included in Flexi Multiradio delivery)

49.0 Nm (36.1 ft-lb)

7/16 DIN

Antenna connector

Antenna jumper cables (not included in Flexi Multiradio delivery)

25.0 Nm (18.5 ft-lb


RA22714EN01GLA0

RA22714EN01GLA0

198



RA22714EN01GLA0

RA22714EN01GLA0

199


Flexi Multiradio BTS GSM/EDGE Installation Appendix - Common Configuration


RA22714EN01GLA0

RA22714EN01GLA0

200


Common Configuration Examples of Flexi Multiradio BTS configurations 3 Pipe RFM 900 3 Pipe RFM 1800

3 Pipe RFM 3 Pipe RFM

ESMC System Module

3 Pipe RFM

FSMx

ESMB System Module FSMx Multimode SM

3 Pipe RFM ESMC

3 Pipe RFM

3 Pipe RFM

ESMC

3 Pipe RFM ESMC

LTE LTE

ESMB

Sys module

3 Pipe RFM

Wall/Pole Up to 6/6/6

3 Pipe RFM

3 Pipe RFM

3 Pipe RFM

3 Pipe RFM

ESMC

ESMC

Stack Up to 12/12/12

Dual band 900 8/8/8@15W 1800 4/4/4@15W

LTE

HEX

3 Pipe RFM

FRMx

3 Pipe RFM ESMC FAN

batt batt batt batt

FRMx

Outdoor cabinet with batteries Concurrent Mode @20W/carrier 900 GSM 4/4/4, WCDMA 2/2/2 1800 GSM 2/2/2, LTE 1/1/1

Indoor Cabinet 36/36/36 with Multi BCF FRMx with 3 modules (6KW)

*LTE Line Terminating equipment For internal use only 201 © Nokia Siemens Networks

RA22714EN01GLA0

For the configurations where the number of antennas is specified as X or Y: • X = the number of antennas required for 1UD and antenna-optimised configurations • Y = the number of antennas required for 2UD configurations

RA22714EN01GLA0

201


Common Configuration Common Sector Configuration # of carriers (2G-3G)

Max Tx Power

Antenna optimized

# of RF branches (pipes)

# of antennas

1

60

No

1

1 or 2

2

30

No

1

1 or 2

3

20

No

1

1 or 2

4

15

No

1

1 or 2

6

10

No

1

1 or 2

2

60

Yes

2

2

4

30

Yes

2

2

6

20

Yes

2

2

8

15

Yes

2

2 or 4

12

10

Yes

2

2 or 4

6

30

Yes

3

2 or 4

1 (2G) – 1 (3G)

40 – 20

No

1

1 or 2

2 (2G) – 1 (3G)

20 – 20

No

1

1 or 2

20 – 40

10 – 40 3 (3G) – 1 (3G)

10 – 30

No

1

1 or 2

2 (2G) – 1 (3G)

20 – 40

Yes

2

2 or 4

4 (2G) – 2 (3G)

20 – 20

Yes

2

2 or 4

1 IDD

60

Yes

2 or 4

2

2 IDD

60

Yes

2 or 4

2

4 IDD

30

Yes

2 or 4

4

1 IDD nad 2 non-

30/30

Yes

2

2

For internal use only IDD 202 © Nokia Siemens Networks

RA22714EN01GLA0

For the configurations where the number of antennas is specified as X or Y: • X = the number of antennas required for 1UD and antenna-optimised configurations • Y = the number of antennas required for 2UD configurations

RA22714EN01GLA0

202


Common Configuration Dedicated 2G Configuration Configurations)

# of FXxx

# of ESMB/C

# of FPAA *) **)

# of FPDA *)

# antennas

Unchained RF Module 1+1+1 up to6+6+6 2UD

1

1

2

1

6

Two chained RF Modules 2+2+2 up to 12+12+12 2UD

2

1

3

2

12

Three chained RF Modules 3+3+3 up to 12+12+12 2UD

3

1

4

2

18

Two unchained RF Modules 2+2+2 up to 12+12+12 2UD

2

1

3

2

12

Three unchained RF Modules 3+3+3 up to 12+12+12 2UD

3

1

4

2

18

Four unchained RF Modules 4+4+4 up to 12+12+12 2UD

4

1

5

3 ***)

24

*) Optional depending on the external power source. The number of power modules is based on maximum power consumption and does not account for redundancy. **) One FPMA supports up to four FPAAs. FPBAs may also be installed in the FPMA. ***) An FSEC is also required since a maximum of two FPDAs can be installed in parallel for each System Module. For internal use only 203 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

203


Common Configuration Antenna-optimised configurations Configurations)

# of FXxx

# of ESMB/C

# of FPAA *) **)

# of FPDA *)

One RF Module antenna optimised 2 up to 12 OMNI 2UD

1

1

2

1

# antenna s 12

Two chained RF Modules antenna optimised 2+2+2 up to 12+12+12 2UD

2

1

3

2

12

Three chained RF Modules antenna optimised 3+3+3 up to 12+12+12 2UD

3

1

4

2

18

*) Optional depending on the external power source. The number of power modules is based on maximum power consumption and does not account for redundancy. **) One FPMA supports up to four FPAAs. FPBAs may also be installed in the FPMA.


RA22714EN01GLA0

RA22714EN01GLA0

204


Concurrent Configuration Common Sector Configuration WCDMA and GSM concurrent mode configurations WCDMA Configuration

GSM Configuration

WCDMA HW Module System Module: FSMD/E No extension module

GSM HW Modules System Module: ESMB

Single band 900: 1+1+1 8/20/40W

Single band 900: 1+1+1 10/20W 2+2+2 10/20W

RFM 900 shared with GSM in concurrent mode

RFM 900 shared with WCDMA in concurrent mode

Single Band 900: 1+1+1 8/20W

Single band 900: 1+1+1 40W 2+2+2 20W 4+4+4 10W


RFM 900 shared with WCDMA in concurrent mode

Single Band 900: 1+1+1 40W

Single band 900: 4+4+4 20W


1 RFM 900 shared with WCDMA in concurrent mode 1RFM 900 in dedicated mode

Single band 900: 1+1+1 8/20W

Dual band conf #1: 1800: 2+2+2 30W 900: 1+1+1 40W Dual band conf #2: 1800: 6+6+6 10W 900: 4+4+4 10W


RFM 900 shared with WCDMA in concurrent mode RFM 1800 in dedicated mode


RA22714EN01GLA0

• Flexi Multiradio BTS is a multiradio BTS, which means that multiple radio technologies can be used concurrently. • The 3-branch RF Module supports GSM/EDGE and WCDMA simultaneously. • The System Modules are separate for GSM/EDGE and for WCDMA. • The GSM/EDGE System Module (ESMB/C) supports up to 18 or 36 TRX capacity, that is, two 3branch RF Module capacity, and it has power and OPT connections for four radios (or radio chains) or System Modules. • In the concurrent mode, the RF Modules as well as the antenna lines can be shared between the System Modules and different radio technologies. • The System Modules have to be interconnected in concurrent operation. • The Flexi Multiradio BTS is seen as a separate logical network element for different radio technologies with common radio resources. • In concurrent mode either ESMB/C or FSMx can be the synchronization master of Flexi Multiradio BTS while the other is the slave. • The operator can define the synchronization master while commissioning the BTS.

RA22714EN01GLA0

205


Flexi Multiradio BTS GSM/EDGE Installation Appendix - Content of Delivery


RA22714EN01GLA0

RA22714EN01GLA0

206


Content of Delivery Power Module (FPMA) Power Module (FPMA) Description Power Module (FPMA) with internal AC and DC cabling and cable support plates

Product Code

Quantity

470139A

1

• Power Module cable

2

entries (identical to EMHA cable entries)

• Alarm cable to the

1

System Module

• Cable clamps

2

• M5 screws for fixing

4

cableentries to the casing

• K30 screws for the cable

4

clamps

• M5 screws for fixing the

2

casing to another casing or plinth

• Cable ties


10

RA22714EN01GLA0

RA22714EN01GLA0

207


Content of Delivery Power AC/DC sub-module (FPAA) and power battery submodule (FPBA) Power AC/DC sub-module (FPAA) Description Power sub-module (FPAA) with two RJ-45 connector seal caps installed

Product Code

Quantity

470140A

1

• Alarm cable

1


2

FPAA to FPMA

power battery sub-module (FPBA) Description Power battery submodule (FPBA) with two RJ-45 connector seal caps installed

Product Code

Quantity

470140A

1

• Alarm cable

1


2

FPBA to FPMA For internal use only 208 © Nokia Siemens Networks

RA22714EN01GLA0

RA22714EN01GLA0

208


Content of Delivery 24V Power Module (FPDA) 24V Power Module (FPDA) Description DC/DC converter core preinstalled inside a 2U casing with cable support plates and with two RJ-45 connector seal caps installed

Product Code

Quantity

470139A

1

• Cable entries

2

• DC output power cables

2

• Alarm cable

1

• AWG 4 (25 mm2)

4

connector single rubber boot

• M5 screws for fixing cable

4

entries to the casing and M5 screws for fixing the casings to each other

• Cable clamps

2

• K30 screws for cable

4

clamps


RA22714EN01GLA0

RA22714EN01GLA0

209


Content of Delivery Flexi System External Alarm Module (FSEB) Flexi System External Alarm Module (FSEB) Description Flexi System External AlarmModule (FSEB)

Product Code

Quantity

471424A

1

• D37 Cable Assembly

1

• Cable tie, PER31

3


RA22714EN01GLA0

RA22714EN01GLA0

210


Content of Delivery Flexi Pole Installation Kit (FPIA) Flexi Pole Installation Kit (FPIA) Description

Product Code

Quantity

Installation plate

1

Straining strap

1

M5 screws

4


RA22714EN01GLA0

RA22714EN01GLA0

211


Content of Delivery Flexi Pole Mounting Kit (FPKA) Flexi Pole Mounting Kit (FPKA) Description

Product Code

Quantity

•Aluminium castings

2

• Assembling bolts

2

• Module fixing screws

6

• Bolt restrainer

2


RA22714EN01GLA0

RA22714EN01GLA0

212


Content of Delivery Pole Mounting Kit delivery (VMPB) Pole Mounting Kit delivery (VMPB) Description Pole Mounting Kit (VMPB)

Product Code

Quantity

469978A

1

• Block

2

• M10 x 120 bolts

4

• M10 x 200 bolts

4

• M10 x 300 bolts

4

• M8 x 25 bolts

8

• Washers

4


Blocks

M10x120 bolts

M8x25 bolts

M10x200 bolts

M10x300 bolts

washer

RA22714EN01GLA0

RA22714EN01GLA0

213


Content of Delivery Flexi Cabinet for Indoor (FCIA) Flexi Cabinet for Indoor (FCIA) Description

Product Code

Flexi Cabinet for Indoor (FCIA)

469978A

Cabinet key

6490006

Quantity 1 2

Cage nuts; pre-installed for the following configurations: • 1+1+1/2+2+2 bypass • 3+3+3/4+4+4 2-way WBC (34 cage nuts are pre-installed and 28 are loose in site pack)

4

Site packs; the site packs are attached with cable ties inside the cabinet. Contents of site package 1: • Guide plates Contents of site package 2: • Loose cage nuts

4


1800

600 822083

600 FCIA, Flexi indoor cabinet

6332594

36 Height Units

RA22714EN01GLA0

RA22714EN01GLA0

214


Content of Delivery Flexi Mounting Kit for Batteries (FMBB) Flexi Mounting Kit for Batteries (FMBB) Description Flexi Mounting Kit for Batteries (FMBB):

Product Code

Quantity

469978A

1

• Bottom plate

1

•Back plate

1

•Front plate

1

•M5 X 10 screws

14

• Cage nuts

8

• Cable ties

3

• Battery fixing adjuster

1


RA22714EN01GLA0

RA22714EN01GLA0

215


Content of Delivery Flexi Mounting Shield 6U (FMSA) Flexi Mounting Shield 6U (FMSA) Description Flexi Mounting Shield 6U (FMSA)

Product Code

Quantity

471614A

1

• Module grounding cable

2

• Grounding cable between

1

the cabinet and plinth

•Cable entry

3

•M8 screws

3

• Cable tie point plates

2

Note: Weight 12 kg (empty) Flexi Plinth FMFA required


RA22714EN01GLA0

RA22714EN01GLA0

216


Content of Delivery Flexi Mounting Shield 6U (FMSA) Flexi Mounting Shield 18U (FMSB) Description Flexi Mounting Shield 18U (FMSB)

Product Code

Quantity

471650A

1

• Module grounding cable

6

• Grounding cable between

1

the cabinet and plinth

•Cable entry

3

•M8 screws

4

• Cable tie point plates

6

Note: • Weight 20 kg (empty) • Flexi Plinth FMFA Required FMSB assembled at site (flat pack delivery) • vandal protection for floor stack


RA22714EN01GLA0

RA22714EN01GLA0

217


Content of Delivery 3 U Module Casings (EMHA) 3 U Module Casings (EMHA) Description 3 U casing (EMHA)

Product Code

Quantity

470316A

1. Rear cover (plastic)

1

• 3 U cable entries

2

• 3 U front cover

1

•3 U rear cover

1

•M5 x 10 screws

4

• M5 x 6 screws

2

• Cage nuts

6 (2 loose, 4 preinstalled)

• Maintenance straps

2

• Grounding cable

1

2. Casing (metal)

3. Front cover (plastic)

Note: Casings are not a part of the module sales item and needs to be ordered separately for stack/wall/pole mounting


RA22714EN01GLA0

RA22714EN01GLA0

218


Content of Delivery mounting kit for floor, wall and pole (FMFA) mounting kit for floor, wall and pole (FMFA) v. 104 delivery content Description Mounting kit for floor, wall and pole

Product Code

Quantity

470149A

1

• Fixing plate for the casing

2

• M5x8 screws

12

•M5x12 screws

1

mounting kit for floor, wall and pole (FMFA) v. 103 delivery content Description Mounting kit for floor, wall and pole

Product Code

Quantity

470149A

1

• Adapter mechanics (used in

1

wall and pole installations only)

• Spring washers (18 pcs for

26

M5 screws and 8 pcs for M8 screws)

• M5x12 screwsFixing plate

2

for the casing

• M5x8 screws For internal use only • M8x20 219 © Nokia Siemens Networks

12 8 RA22714EN01GLA0

RA22714EN01GLA0

219


Content of Delivery Flexi Mounting Covers Front and Back, 2 HU (FMCB) Flexi Mounting Covers Front and Back, 2 HU (FMCB) Description Flexi Mounting Covers Front and Back, 2 HU (FMCB)

Product Code

Quantity

470332A

1. Rear cover (plastic) 2U

1

• 2 HU front cover

1

• 2 HU back cover

1

3. Front cover (plastic) 2U

The Flexi Mounting Covers Front and Back, 2 HU (FMCB), needed with Flexi Power DC/ DC Module 24 V (FPDA)


RA22714EN01GLA0

RA22714EN01GLA0

220


Content of Delivery Long Term Battery Backup Solution (MIBBU) Long Term Battery Backup Solution (MIBBU) Description

Product Code

WPxx • Power Distribution Unit (WPUB) • Wideband Power Unit (WPMB)

469784A

Flexi Power Rectifier (FPRA) • PDA Unit • Temperature Sensor • Accessory bag

CS7000000 CS7000003 CS7000005 CS7000007

Quan -tity 1 1

469950A 1 1 1 1

• Rectifier AA2500L 48/2000

CS7000001

1

• Surge protection device

CS7000002

1

• Flexi battery mounting kit (FMBB)

471459A

1

• Flexi mounting kit for batteries (FMBA)

471020A

1

• Battery box

CS7000008

1

• Battery box wall mounting kit

CS7000010

1

•

Power safe batt 4x12V92F 92Ah/10h • Powersafe batt 4x12V62F 48V- 62Ah

CS71362.03

1

CS7136211

1

• Battery box plinth

CS7000009

1

• Battery box Flexi bracket kit

CS7000011

1


RA22714EN01GLA0

RA22714EN01GLA0

221


Content of Delivery Talk Conversion Kit (EMIA) Talk Conversion Kit (EMIA) Description Talk Conversion Kit (EMIA):

Produc t Code

Quan -tity

471429A

1

• Front door assembly

1

• Back wall assembly

1

• Door alarm cable assembly

1

• Standoff casing plate

1

• Standoff proximity bracket

1

• Door proximity bracket

1

• Ring inlets

1

• M8 x 16 screws

4

• Washer, flat M8

4

•

2

Nut, hex M6

• Washer, M6

2

• Connection pins

4

• Upper lock rod supports

2

• M5 x 10 TORX screws

16


4

• Rivets

4


Standoff casing plate

Standoff bracket

Upper lock rod support (2 pcs)

M8 (4 pcs)

M6 Nut (2 pcs)

M5 (16 pcs)

Ring Inlet (1 pc)

Door proximity bracket

Front door assembly Backwall assembly

Door alarm sensor wirh wire

M3 (4 pcs)

Flat washer (4 pcs)

Start washer (2 pcs)

Connection pins (4 pcs)

Rivet (4 pcs)

Door switch parts

RA22714EN01GLA0

RA22714EN01GLA0

222


Content of Delivery Talk Conversion Kit (EMIB) (1/2) Talk Conversion Kit (EMIB) Description Talk Conversion Kit (EMIB):

Produc t Code

Quan -tity

471953A

1

• Front door assembly

1

• Back wall assembly

1

• Top IP-cover

1

• Air guide plate

1

• Cover plate

2

• Dummy Panel

2

• Top support plate

1

• Rack side plate right

1

assembly

• Rack side plate left

1

assembly

• Door alarm cable assembly

1

• Rack plinth

1

• Cont’d ……..


RA22714EN01GLA0

RA22714EN01GLA0

223


Content of Delivery Talk Conversion Kit (EMIB) (2/2) Talk Conversion Kit (EMIB) … cont’d Description

Produc t Code

Quan -tity

…. Cont’d

• Rack plinth

1

• Top support C-plate

1

• Support rail

14

• Standoff proximity bracket

1

• Grommet

2

• Door proximity bracket

1

• M8 x 16 screws

4

• Hole Nut

40

• Nut, hex M6

2

• Upper lock rod supports

2


28

• M4 x 10 screws

4

•

4

M3 x 6 TORX screws

• Cable tie

Door sensor assembly accessories bag (1pcs)

6 Door sensor assembly accessories bag (1pcs)


RA22714EN01GLA0

RA22714EN01GLA0

224


Content of Delivery Flexi Mounting Auxiliary Bracket (FMAA) Flexi Mounting Auxiliary Bracket (FMAA) Description

Produc t Code

Quan -tity

Flexi Mounting Auxiliary Bracket (FMAA):

471657A

• Bracket

822962

1

• M5 x 10 screw

6150240

8

• M6 x 10 screw

6150343

8

• M4 x 10 screw

6151410

4

• M5 x 25 screw

6150275

4

• M5 spring washer

6368770

4


RA22714EN01GLA0

RA22714EN01GLA0

225


Content of Delivery LMP cable delivery (ELCA), BBU Alarm Cable delivery (EBCA), Q1 cable delivery (EQCA), Flexi System Alarm Cable (FSAA) LMP cable delivery (ELCA) Description

Product Code

LMP cable 50 m (164.0 ft), ELCA

471370A

Quantity 1

BBU Alarm Cable delivery (EBCA) Description

Product Code

Quan -tity

BBU Alarm Cable Kit (EBCA) 2m (6.5 ft)

4717464

1

Q1 cable delivery (EQCA) Description

Product Code

EQCA Q1 Cable 3.01 m (9.9 ft)

471384A

Quantity 1

Flexi System Alarm Cable (FSAA) Description

Product Code

Flexi System Alarm Cable (FSAA): D37 cable assembly 15 m (49.2 ft.) For internal use only 226 © Nokia Siemens Networks

471628A

Quantity 1

RA22714EN01GLA0

RA22714EN01GLA0

226


Content of Delivery Synchronisation cable deliveries (ESxA) Synchronisation cable deliveries (ESxA) Description

Produc t Code

Quan -tity

ESUA synchronisation cable for Flexi Ultra 12 m (39.4 ft)

471372A

1

ESFA synchronisation cable for Flexi 12 m (39.4 ft)

471371A

1

ESLA synchronisation LMU Cable 2 m (6.6 ft)

471377A

1


RA22714EN01GLA0

RA22714EN01GLA0

227


Flexi Multiradio BTS GSM/EDGE Installation Appendix - FSEB interface signals and connector pin assignments


RA22714EN01GLA0

RA22714EN01GLA0

228


FSEB interface signals and connector pin assignments (1/5) FSEB printed wiring board


RA22714EN01GLA0

RA22714EN01GLA0

229


FSEB interface signals and connector pin assignments (2/5) EACX connector I pin assignment


EACX connector II pin assignment

RA22714EN01GLA0

RA22714EN01GLA0

230


FSEB interface signals and connector pin assignments (3/5) Screw terminal pin assignment

EACX connector II pin assignment

1)The X connectors are marked on the bottom of the FSEB PCB.


RA22714EN01GLA0

RA22714EN01GLA0

231


FSEB interface signals and connector pin assignments (4/5) Screw terminal pin assignment … cont’d

Smoke detector power supply interface

1)The X connectors are marked on the bottom of the FSEB PCB.


RA22714EN01GLA0

RA22714EN01GLA0

232


FSEB interface signals and connector pin assignments (5/5) Flexi System Alarm cable (FSAA) pin colour mapping

"CAN_L" and "CAN_H" refer to an internal bus used between ESMB/C and FSEB.


RA22714EN01GLA0

RA22714EN01GLA0

233


Flexi Multiradio BTS GSM/EDGE Installation Planning Appendix - Antenna Line


RA22714EN01GLA0

RA22714EN01GLA0

234


Antenna Line Antenna jumper cable requirements Antenna jumper cable requirements: • 1/2" or 3/8" antenna jumper cables can be used. 1/2" antenna cable connectors can be connected directly to the module if a right angle connector is used. • The length should be determined based on the Flexi Multiradio BTS GSM/EDGE installation option (for example pole, wall, cabinet, 3rd party cabinet) and the distance of the BTS from the antenna feeder line. • Antenna jumper cables must be IP54-rated or better.


RA22714EN01GLA0

Basically, Jumper cables are low–loss and flexible, which allows easier connection to units such as the WCDMA MHA unit without causing unnecessary stress to the connected units (vs. feeder cables).

RA22714EN01GLA0

235


Antenna Line Antenna Line configurations with or without MHA Antenna Line configurations without MHA

Antenna Line configurations with MHA

X-pol antenna

X-pol antenna

Jumper cable Jumper cable

MHA Feeder connector Grounding kit Feeder

Jumper cable Feeder clamp

Feeder connector Grounding kit

Feeder clamp Grounding kit


Jumper cable

Feeder Grounding kit

RA22714EN01GLA0

RA22714EN01GLA0

236


Antenna Line Antenna line configurations – with diplexer or triplexer

X-pol Dual Band antenna ( internal combiner) Jumper cable Feeder connector Grounding kit Feeder Jumper cable

Diplexer

Jumper cable


Flexi Multiradio BTS GSM/EDGE

RA22714EN01GLA0

RA22714EN01GLA0

237

02 RA22714EN01GLA0 Flexi Multiradio Installation

Recommend Documents