Uji Kompetensi "Bilangan" Matematika Kls.7 SMP Kurikulum 2013
Catalogue HY11-3500/UK
Pilot Operated Proportional Propor tional Reducing Valve Valve
Characteristics
Series VMY
Proportional pressure p ressure reducing valves of the series VMY allow the variable adjustment of the reduced pressure from 0 bar up to the nominal pressure. The valve consists of a spool type main stage and a proportionally operated pilot stage. The desired pressure can be variably set corresponding to the command signal specified on the amplifier. The proportional solenoid converts the current of the amplifier into force on the valve poppet of the pilot stage. Typical applications are pressure systems, test equipment, or counterweight systems. The optimum performance can be achieved in combination with the digital amplifier module PCD00A-400 for open loop systems or with PWDXXA-40* for closed loop systems.
VMY*K06
4
Function VMY*K06 With the proportional solenoids de-energized the main spring forces the main spool into the neutral position. Port Port A is connected to port T. Thus the reduced pressure only depends on the back pressure pressure in the external external drain pipe and/or the tank pressure and can accordingly be reduced down to 0 bar. The pressure present in the P line delivers the pilot oil to the pilot stage via a flow control valve. When the proportional solenoid is energized, the pilot pressure is increased in the pilot pressure area, and the main spool moves against the spring until the connection P - A opens. The regulation of the reduced pressure on connection A takes place by the constant comparison of the actual pressure and the reference pressure of the pilot stage.
VMY*K10 The valve spool is designed so that the connection B-A is open in the neutral position and is closed in the working position.
VMY*K06N
VMY*K10
VMY*K06
Neutral position
Por t B has to be blocked VMY UK.INDD RH 20.07.2017
Port X has to be blocked
VMY*K10
Catalogue HY11-3500/UK
Pilot Operated Proportional Reducing Valve
Ordering Code / Technical Data
Series VMY
Ordering code
VMY
K
1
Reducing Pressure Proportional Nominal valve stages solenoid size 9 V / 2.5 A Code
4
Pilot
Seals
P Design High series pressure (not required for channel ordering)
Pressure stages
064
up to 64 bar
100
up to 100 bar
160
up to 160 bar
210
up to 210 bar
315
up to 315 bar
Code
Nominal size
06
NG06
10
NG10
Code N
2)
V
Seals NBR FPM
Pilot oil Code
Size
omit
10
N
1)
T
Pilot
Drain
Internal Internal
pmin [bar] 3-4
06
Internal External 0.5 - 1
06
Internal Internal
1-2
Technical data General Design Nominal size Interface Actuation Mounting position Ambient temperature MTTFD value Weight Hydraulics Max. operating pressure
Pressure stages Nominal flow Fluid Viscosity permitted recommended Fluid temperature Filtration Linearity Repeatability Hysteresis Response time Electrical Duty ratio Protection class Nominal voltage Max. current Nom. current Ambient temperature Coil resistance Solenoid connection Power amplifier, recommended 1)
Connection on port Y1 or Y2. Not for NG06.
2)
VMY UK.INDD RH 20.07.2017
3 way proportional reducing valve, pilot operated, spool design 06 (DIN NG06/CETOP 03/NFPA D03) 10 (DIN NG10/CETOP 05/NFPA D05) Subplate mounting according to ISO 5781 Proportional solenoid unrestricted [°C] -20 ... +60 [years] 75 [kg] 2.8 5
[cSt] / [cSt] /
Size 06: [bar] Ports P, A 315; Port T, Y depressurized; port B has to be blocked Size 10: [bar] Ports A, B 350; Port Y depressurized; port X has to be blocked [bar] 64, 100, 160, 210, 315 [l/min] 40 160 Hydraulic oil according to DIN 51524 [mm²/s] 20 ... 400 [mm²/s] 30 ... 80 [°C] -20...+70 (NBR: -25...+70) ISO 4406 (1999); 18/16/13 [%] See characteristic pressure curves ±3.5 at > 15 % pnom. [%] <±2 [%] <3 [ms] <150 <200 [%] 100 ED IP65 in accordance with EN 60529 (with correctly mounted plug-in connector) [VDC] 9 [A] 2.7 [A] 2.5 [°C] -20...+70 [Ohm] -2.1 (at 20 °C) Connector as per EN 175301-803 PCD00A-400
Catalogue HY11-3500/UK
Pilot Operated Proportional Reducing Valve
Characteristic Curves
Series VMY
NG06 Characteristic pressure lines p = f (Uset) Setting range max. 64 bar ]
Setting range max. 210 bar ]
65 r a
220 r a b[
b[ p p e
e
60 r u
r
200 u
s s s s e e r P
r P
55
180
50 160
45
4
140
40
35
120
30
100
25
80
Q = 0 l/min
20 60
Q = 0 l/min
typical characteristic curve
15 typical characteristic curve
10
40
20
5
0
0
1
1
250
2
3
4
5
6
0 0
7
8 9 10 Set value Uset[V] 500 750 1000 1250 1500 1750 2000 2 250 2500 Solenoid current IS [mA]
1
1
2
3
4
5
6
7 8 9 10 Set value Uset[V] 250 500 750 1000 1250 1 500 1 750 2000 2 250 2500 Solenoid current Is [mA]
NG06 p/Q characteristics Setting range max. 64 bar ]
100 r a b[
Flow A - T p
Flow P - A
e
80 r
2500 mA u s s
60 e r
1875 mA P
40 1250 mA 20
40
30
20
All characteristic curves measured with HLP46 at 50 °C. VMY UK.INDD RH 20.07.2017
625 mA
pmin
0 mA
10
0
10
20
30 40 Flow Q [l/min]
Catalogue HY11-3500/UK
Pilot Operated Proportional Reducing Valve
Characteristic Curves
Series VMY
NG06 p/Q characteristics Setting range max. 100 bar ]
120 r a b[
2500 mA
100 p
Flow A - T
e r u
Flow P - A 1875 mA
80 s s e r P
60 1250 mA
40
625 mA
20 0 mA
40
4
pmin
30
20
10
0
10
20
30 40 Flow Q [l/min]
Setting range max. 160 bar ] r a b[ p e r u s s e r P
200 180 160 140 120 100 80
2500 mA Flow A - T
Flow P - A 1875 mA
1250 mA
60 40 20 0
625 mA 0 mA
40
pmin
30
20
10
0
10
20
30 40 Flow Q [l/min]
Setting range max. 210 bar ]
260 r a [b
2500 mA
220 p e r u
Flow A - T
180 s
Flow P - A
s
1875 mA e r P
140 1250 mA
100 60 20
0 mA
40
625 mA
pmin
30
20
10
0
10
20
30 40 Flow Q [l/min]
Setting range max. 315 bar ]
340 [b
300 e
260
a
r p r u s
2500 mA Flow A - T
Flow P - A 1875 mA
220 s e r P
180 1250 mA
140 100 60
625 mA
20 40
pmin
0 mA
30
20
All characteristic curves measured with HLP46 at 50 °C. VMY UK.INDD RH 20.07.2017
10
0
10
20
30 40 Flow Q [l/min]
Catalogue HY11-3500/UK
Pilot Operated Proportional Reducing Valve
Characteristic Curves / Accessories
Series VMY
Step response Typical curve
4
All characteristic curves measured with HLP46 at 50 °C.
Accumulator plate H06VMY-1350
VMY UK.INDD RH 20.07.2017
Catalogue HY11-3500/UK
Pilot Operated Proportional Reducing Valve
Characteristic Curves
Series VMY
NG10 p/Q characteristics for pilot oil supply from high pressure channel P Setting range max. 64 bar
4 Setting range max. 100 bar
Setting range max. 160 bar
Setting range max. 210 bar
All characteristic curves measured with HLP46 at 50 °C. VMY UK.INDD RH 20.07.2017
Catalogue HY11-3500/UK
Pilot Operated Proportional Reducing Valve
Dimensions
Series VMY
NG06
Port Y: G1/4 VMY*K06T: Ports Y1 and Y2: closed VMY*K06N: Drain port Y1 or Y2 Port Y1 closed, Port Y2 opened
Surface finish
Bolt kit FPM BK375
4x M5x30 ISO 4762-12.9
7.6 Nm ±15 %
Mounting pattern ISO 5781-03-04-0-00 The connection B must be locked onto the subplate for standard applications.
VMY UK.INDD RH 20.07.2017
SK-VMY-L06-V
4
Catalogue HY11-3500/UK
Pilot Operated Proportional Reducing Valve
Dimensions
Series VMY
NG10
4
Surface finish
Bolt kit FPM BK389
4x M10x50 ISO 4762-12.9
Mounting pattern ISO 5781-06-07-0-00 1)
1)
Deviating from ISO the Y port has Ø 14.7 instead of Ø 4.8.