Vector Vertical Platformlift User manual 2005.09.19
A ThyssenKrupp Elevator company
ThyssenKrupp Accessibility ThyssenKrupp
Vector Vertical Platformlift - User manual
READ THESE INSTRUCTIONS THROUGH CAREFULLY BEFORE USING THE VECTOR VERTICAL PLATFORMLIFT PAY PARTICULAR ATTENTION TO THE CHAPTERS “SAFETY INSTRUCTIONS ” AND “OPERATION” STORE THESE INSTRUCTIONS SO YOU ALWAYS HAVE NECESSARY INFORMATION AT HAND
We undertake a policy of continual review, and research, which may lead to changes in the products, or technical information, illustrated in this manual.
© 2005 ThyssenKrupp Accessibility All rights reserved. No part of this document may be copied and/or published by means of printing, photocopies, microlms or any other
method without the prior written permission of ThyssenKrupp Accessibility.
2005.09.19
Vector - Vertical Platformlift
User manual
Table of contents Preface Vertical platform and the environment
2 3
1.
Safety Instructions
4
2.
Operation 2.1 To call the lift 2.2 Operating the lift from the platform console
5 5 5
3. Options 3.1 Key Switching 3.2 Key Locking 3.3 Automatic Entrances 3.4 Stay open facility for door closer/opener
6 6 6 6 6
4.
7 7 7 8
Fault Finding 4.1. Emergency Procedures 4.1.1 Instruction for emergency lowering/raising of the platform 4.1.2 Instruction for emergency opening of door
5. Maintenance 6. Service
A ThyssenKrupp Elevator company
9 10
ThyssenKrupp Accessibility ThyssenKrupp
User manual
Vector - Vertical Platformlift
2005.09.19
Preface Congratulations! You have chosen a Vector vertical platformlift from ThyssenKrupp Accessibility. A modern, userfriendly and safe product that will give you years of service. We will do everything in our power to justify the condence you have placed in us. To make the best possible use of the vertical platformlift, it is important that you read these instructions carefully before rst using the lift. These instructions These instructions are meant for you as the user of Vector vertical platformlift. The instructions contain all necessary information for the correct and safe use of the lift. All chapters and paragraphs are numbered. The page numbering can be found at the bottom of each page. Service and technical support To be sure that your Vector works well and safely, it is important that the lift is inspected and serviced regularly. We recommend that you establish a service contract for this so that you are always assured of a lift in optimal condition. Contact your supplier for more details. For information about settings, maintenance or other matters that are not addressed in these instructions, you can contact the troubleshooting service of your supplier. Further information can be found in chapter 6.
2
2005.09.19
Vector - Vertical Platformlift
User manual
Vertical platform and the environment Batteries The Vector vertical platformlift includes two main batteries for the supply of the emergency lowering system, 12 V. These batteries may only be replaced by authorised/ trained ThyssenKrupp Accessibility BV service mechanics. Do not deposit old batteries with household waste, but return them when you buy new batteries. If this is not possible, ask the sanitation service of your municipality where you should dispose the old batteries. Disposing of the home lift Home lifts that are no longer in use are often taken back by your supplier after consultation. If this is not possible, enquire at your municipality for possibilities of returning them, recycling them or environmentally friendly ways of processing the materials. Symbols In this service manual the following symbols occur: TIP
Tips and advice to be able to carry out the relevant actions more easily.
ATTENTION
Actions that could result in damage to the chair lift, the surroundings or the environment if they are not carried out cautiously.
3
User manual
Vector - Vertical Platformlift
2005.09.19
1. Safety Instructions This Vector platformlift incorporates many safety features including: - Pressure sensitive safety edges on the platform edges and the top of the platform control panel. These will stop the platform should an obstruction be encountered. When the lift has stopped you can either remove the obstructing item yourself or call for assistance from someone outside the lift. - Constant pressure controls that stop the lift when pressure is not maintained. If pressure on a button is released away from the landing level but within 100mm (4 inches) of this then a safety mechanism will prevent the lift from continuing in the same direction once pressure is re-applied. In this case the lift should be returned to the previous level and the journey recommenced. - On-board alarm call which can be linked (optional) to a remote audio/visual unit or operate a hands free telephone auto-dialler system. - Emergency stop button on platform control console. Please note the following: - Its important that someone is available external to the lift to carry out any emergency procedure should this become necessary. This assistance can best be summoned using the on-board alarm call. - Other building users should be made aware of the need to leave the landing areas clear to enable the doors to open without obstruction and the wheelchair user to manoeuvre easily when entering and leaving the lift. A turning circle of 1500mm minimum diameter is recommended at each level for this. - The lift is designed to carry one wheelchair user and attendant up to the load stated on the lift. It may also be used for standing passengers provided the maximum overall weight does not exceed this limit. - Do not allow anyone to play on the lift. ATTENTION
NEVER use the lift in the event of a re (unless so directed by the emergency services).
4
2005.09.19
Vector - Vertical Platformlift
User manual
2. Operation 2.1 To call the lift If key switches (optional) are tted, rst refer to the appropriate section in chapter 3. If the lift platform is already at the required level, skip the rst two steps described below. - Press and hold the call button adjacent to the entrance at the oor level to call the lift. - Release the call button only once the lift has stopped automatically at the landing. - Whilst the platform is at a landing level, the entrance catch is disengaged allowing access to the platform. If an automatic entrance (optional) is tted then this will open once the platform arrives at the landing or once a call button is pressed at a landing where the platform is stationary.
2.2 Operating the lift from the platform console The platform console controls consist of the floor designation buttons (image 2.1), the alarm call button (image 2.2a) and the emergency stop button (image 2.2b). The control panel is illuminated by a neon light. This light along with the alarm has an emergency battery backup. The user should access the platform, then the entrance should be pulled closed. If an automatic entrance (optional) is tted then it will close following a time delay or once a button requesting a different oor has been pressed. Constant pressure should be applied to the chosen oor designation button (image 2.1) on the console until the lift platform stops automatically at that level. Once the platform reaches the chosen oor level, the entrance catch is disengaged allowing egress from the platform. If an automatic entrance (optional) is tted then it will open once the platform arrives at that oor level.
Image 2.1
a
b
Image 2.2
To summon assistance the alarm call button should be pressed (image 2.2.a). The alarm is reset using the push button marked ‘Alarm Reset’ within the control cabinet. The control cabinet is accessible through the locked door adjacent to the upper entrance. Should the lift not stop when pressure is removed from all control buttons, the emergency stop button should be pressed (image 2.2.b). This will lock down and stop the lift. To reset this button turn it clockwise until the head returns to the upper position. The lift should now be checked by service personnel of ThyssenKrupp Accessibility- details are given in chapter 6. 5
User manual
Vector - Vertical Platformlift
2005.09.19
3. Options Any optional features tted to your unit will be indicated by a tick.
3.1 Key Switching If this option is chosen, a key switch is located adjacent to each landing call button. The switch at the required oor level must be turned to the on position before the call button can be used to call the lift. The key must be turned to the off position for removal. Key switching restricts operation of the platform but does not always prevent access to the platform as the entrance catch is automatically disengaged when the platform reaches the oor level.
3.2 Key Locking If an automatic entrance is used the call button at that landing level can be replaced by a key switch to call the lift. The entrance catch automatically engages after a short delay when the platform remains stationary at a oor level. This allows access to the platform, not just its operation, to be restricted. The catch is disengaged by turning the key switch provided that lift is stationary at a oor level. Operation of a oor designation button on the platform console also releases the catch. Key switches can be tted in place of any oor designation button to restrict access to certain levels.
3.3 Automatic Entrances Automatic operation increases independent accessibility and can be provided for gates or doors. When the platform is stationary at a oor level and the local call button is pressed, the entrance will automatically open. When the platform arrives at a oor level the entrance will also automatically open. The entrance will remain open for a preset time period (service adjustable) and then close. If the opening or closing door encounters any obstruction a clutch mechanism ensures that its motion does not continue until the obstruction is removed. Automatic door operation can be switched off, if required, using the switches on the top of the door mounted units at individual entrances.
3.4 Stay open facility for door closer/opener By operating a catch on the opener/closer the door can be held open.
6
2005.09.19
Vector - Vertical Platformlift
User manual
4. Fault Finding Should the platform not work correctly, please check the following: - Emergency stop buttons on the control panel on the platform should not be pushed in (turn the buttons clockwise to deactivate). - The doors are closed and the door contacts are undamaged and clean. - Mains isolator is switched on. - The hand winding device is not connected. - The safety edge around the platform oor and above the control console is not depressed Has pressure on a control button been released when the platform is positioned away from a landing level but within 100mm (4 inches) of it. If so, a safety mechanism will prevent the platform from continuing in the same direction once pressure is re-applied. In this case the lift should be returned to the previous level and the journey recommenced. If the lift fails to work after you have completed these checks, please call the ThyssenKrupp Accessibility service desk. Servicing and call-out details are provided in chapter 6 of this manual.
4.1. Emergency Procedures ATTENTION
It is important to read this chapter carefulley before taking emergency action.
- The mains isolator MUST always be switched off before attempting to open any access panels, even during a power failure, to avoid injury to personnel. - There is a risk of falling when a landing door is opened (using the manual release) without the platform being at that level. Always keep the doors closed and check the function of the lock so nobody can fall into the shaft. 4.1.1 Instruction for emergency lowering/raising of the platform - Ensure that the power is switched off at the mains isolator. - Unlock and remove (by lifting out and upwards) the cover to the electrical cabinet allowing access to the hand-winding device. - Switch off mains power supply using the switch marked ‘Lift Machinery’. - The hand-winding device is located on the inside of the cabinet cover. - Push the hand-winding device into the socket, until it is engaged, and turn anticlockwise to lower the platform (clockwise to raise the unit). Inserting the crank also lifts a metal lever to isolate power to the platform motor.
7
User manual
Vector - Vertical Platformlift
2005.09.19
- Continue to turn the hand-winding device until the platform has reached the nearest landing that allows safe evacuation. - Once the platform is at the landing level then the door catch will release automatically. It should now be possible to open the landing door. - If the platform has been lowered too far at the lowest landing, the limit switch may have been activated and it will be necessary to slightly raise the platform again. - Remove the crank and hang it back inside the cabinet cover. - Once the platform is empty, reset any alarm using the push button marked ‘Alarm Reset’. - Replace and lock the cabinet cover. - Contact service personnel - details are given in chapter 6. 4.1.2 Instruction for emergency opening of door - Ensure that the power is switched off at the mains isolator. - Unlock and remove (by lifting out and upwards) the cover to the electrical cabinet. - Switch of the mains power in the electrical cabinet using the switch marked ‘Lift Machinery’. - Use the special key which is hanging on the inside of the cabinet cover to loosen the screw which covers the hole in the door panel at the lock. - Use a screwdriver or similar tool in the hole and push up the locking cylinder (see diagram). ATTENTION
For 1100mm high gate and re rated door the locking cylinder should be pushed to the side not up.
- Whilst the locking cylinder is pushed up and held the door catch is disengaged allowing the door to be opened. - Once the platform is empty, close the door and replace the screw. - Reset any alarm using the switch located in the electrical cabinet and marked ‘Alarm Reset’. - Replace and lock the cabinet cover. - Contact service personnel - details are given in chapter 6.
Image 4.1: Door catch release system.
8
2005.09.19
Vector - Vertical Platformlift
User manual
5. Maintenance Your lift should be serviced within 6 months of installation and twice a year thereafter (in case of high usage four times a year). That’s why - if you have not already done so - we recommend you to take a ThyssenKrupp Accessibility servicing plan today. Besides keeping the lift in rst class condition - ensuring that it continues to comply with the latest regulations - your ThyssenKrupp Accessibility engineer can identify parts which may soon need replacing. Thus adding to the users’ quality of life by helping to prevent breakdowns and giving you valuable peace of mind. - The ThyssenKrupp Accessibility Regular Servicing Plan provides comprehensive inspection, testing and adjustment at recommended intervals. - ThyssenKrupp Accessibility Comprehensive Cover goes one step further; also covering you against the cost of genuine replacement parts, as and when required. For further information, write to your dealer, or: ThyssenKrupp Accessibility Van Utrechtweg 99 2921 LN Krimpen aan den IJssel The Netherlands Or telephone: +31 180 530 988 during normal ofce hours. Routine care of your Vector vertical platformlift involves little more than just keeping it clean. In order to keep the lift in optimal condition switch off at the mains supply and carry out the following actions: - Wipe away dirt using a mild detergent solution and a just-damp cloth. - Use an automotive paint cleaner to remove any stubborn streak marks on the paint work, then apply an automotive hard silicone wax to give a protective nish. Ensure handrails, door handles, ramps and other such parts are not waxed. Of course, you should always ensure that: - The entrances are kept free of any obstruction. - No-one overloads or otherwise misuses the lift, and any damaged or missing notices are replaced immediately.
9
User manual
Vector - Vertical Platformlift
2005.09.19
6. Service In the unlikely event that your lift needs attention between service visits, you can report the fault by telephoning your dealer. We will ask for details of the problem - plus some standard information. Please give us the following information whenever you phone: Owner’s name: Installation address:
Phone No. Lift Type. Vector Lift serial No. Date of installation:
ATTENTION
If a breakdown results from failure to use the Simple Fault Finding procedures on page 5, ThyssenKrupp Accessibility reserve the right to charge a call-out fee - even if the lift is still under guarantee.
10
