Question and answer for ultrasonic testingFull description
Deskripsi lengkap
REPORTDeskripsi lengkap
UT procedureFull description
Ultrasonic Testing HandbookFull description
Descripción: Ultrasonic Testing Handbook
Word Document - used for study for PCN Level 2Descripción completa
phased array ultrasonic testingFull description
National aeronautics and space administration. Prepared under NAS 8-20185 by General Dynamics. Manual for beginers.Descripción completa
TRAINING MANUAL FOR NON-DESTRUCTIVE TESTING TECHNIQUESFull description
TRAINING MANUAL FOR NON-DESTRUCTIVE TESTING TECHNIQUESDescripción completa
ts
ultrasonic motor seminar reportFull description
SOLUTION OF QUESTION BANK OF THE PAPER ULTRASONIC INSTRUMENTATION UNDER THE CODE EI703(a). THIS IS AN ELECTIVE SUBJECT STUDIED BY STUDENTS OF INSTRUMENTATION AND CONTROL UNDER SOME UNIVERSIT…Descripción completa
Codes for Automatic Ultrasonic Testing (AUT) of Pipeline Girth Welds
ASNT-Level II Study Guide Ultrasonic Testing-Method (2002)Full description
Edition II Published by EEC Electronic & Engineering Co. P.O.Box No.17356 Andheri(W) Bombay 400 058Descripción completa
Ultrasound Quiz 1
Page Page 1 of 2 Ultrasound Quiz 1
~ First name ~
1
~ Last name ~
Surface or Rayleigh waves travelling along the surface of relative thick solid material, penetrate to a depth of approximately:
One wavelength Two wavelengths Three wavelengths Infinite wavelengths
2
3
4
5
6
7
Which of the following could influence the behavior of a transducer?
Electrical construction Material construction Mechanical construction All of the above Which type of screen presentation displays the amount of received ultrasonic energy as a function of time?
A-scan B-scan C-scan All of the above The material of the reference standard used to setup for a flaw inspection:
Can be made from similar material as long as the velocity is the same Should be the same material being inspected Must have the same impedance values as the base material Can only be used once Which of the following waves is only able to travel through a thin section of material?
A longitudinal wave A shear waves A surface wave A lamb wave When a single element transducer is operating in the pulse echo mode, the element:
Can not start receiving reflected signals until the element has stopped ringing from its transmit function Needs to have a high pulse rate Should be used in the dual mode Can only be made with lithium sulfate In order to have a reasonable chance at detecting a discontinuity, the reflective surface of the discontinuity must have a dimension that is at least as long as ________ wavelength.
One-half One Two 0ne-quarter
8
9
10
11
The terms used to describe a technique s ability to locate flaws are:
Sensitivity and penetration Space and time Sensitivity and resolution Frequency and size Couplant displaces the__________ and makes it possible to get more sound energy into the test specimen.
Surface rust Surface blemishes Sound energy Air Beam spread is greater when using:
High frequency transducers Low frequency transducers Angle beam transducers Larger diameter transducers Which type of transducer can be used to scan wide areas when high sensitivity is not required?
Single crystal transducer of small diameter Composite transducer Paint brush transducer
12
13
14
15
16
17
18
What type of transducer contains two independently operating elements in a single housing?
Crystal mosaic transducer Dual element transducer Liquid crystal transducer Bi polar transducer DACC stands for:
Distance Amplitude Correction Curve Direct Application Correction Curve Distance Area Correction Calculation Distance Area Computer Controlled The number of cylces per second is the definition of:
Wave speed Frequency Hertz None of the above Acoustic impedance is identified by the letter:
Z I V P Which of the following would make a good couplant?
Water Oil Glycerin All of the above A calibration block produced by the International Institute of Welding is called:
An IIW block A DSC block A rompus block A shear wave calibration block Which type of screen presentation displays a plan-type view of the location and size of the test specimen features?
A-scan B-scan C-scan All of the above
19
20
What is used to support the active element and dampen the transducers characteristics?
Resin Oil Backing material with a similar the impedance of the transducer Any of the above will work Which type of transducer will have better resolution?
A slightly damped transducer A small size and low frequency transducer A highly damped transducer All of the above
Copyright
The Collaboration Collaboration for NDT NDT Education.. Education..