Translated version of OptiX 155622H(Metro 1000) 产品软件升级指导 书.docx Data encoded using the object the preparation of sector Optical network technical support engineers optical network technology center Product name product version information version OptiX Metro 1000 V1.1 The OptiX 155622H (Metro 1000) product software upgrade instructions Intends to review for approval System: core: core: standard: Huang Qiang Day, every day Period: Period: Period: Period: November 24, 2005 Date Huawei Technologies Co., Ltd. Copyright All Rights Reserved
61281792.doc Confidentiality: the internal public Repair Date 2005-112005-11-24 2005-112005-11-26 Order Note Author Huang Qiang Huang Qiang Record Description The first draft completed in accordance with service Lixian Song Jing Guangzhi views modify Revision V1.0 V1.1 V1.1 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 2 of 43
61281792.doc Confidentiality: the internal public Head A Record Overview ................................................ .................................................. ..................................... 6 1.1 1.2 1.3 1.4 1.5 upgrade work with .......................................... .................................................. ..................... 6 upgrade Privacy Policy Information .......... .................................................. .................................................. ......... 6 upgrade has sequence .................................... .................................................. ................................. 6 software channels ............ .................................................. .................................................. ....... 7 upgrade process norms ...................................... .................................................. preparation ............................... 7 Upgrade work ............. .................................................. .................................................. .. 7 upgrade sequence ............................................ .................................................. ................................ 9 Upgrade steps .............. .................................................. .................................................. ............ 9 2.3.1 use the Navigator to load the software method ....................... .................................................. ..... 9 2.3.2 Toolkit software to be loaded ........................... ................................................. 10 2.3.3 host software upgrade steps ......................................... .................................................. .... 12 2.4 2.5 Upgrade items ....................................... .................................................. upgrade instructions ............................ 12 version ............. .................................................. ................................. 12 2.5.1 the Optix Metro1000 mainstream host software upgrade summary table (table a prerequisite for the existing version of the complementary relationship between the correct) ....................................... .................................................. ............................... 13 2.5.2 The various upgrade detailed description ........ .................................................. ................................. 14 2.6 2.7 upgrades focus on examination of the contents ........ .................................................. ............................................... 18 host software load exception handling ............................................ .................................................. 18 2.7.1 problem 1: The host software can not be loaded ...................................... ............................................... 18 2 SCB board software upgrade ............................................. .................................................. ..................... 7 2.1 2.2 2.3 3 Business board the board software and FPGA upgrade ........................................ ................................................. 20 In 3.1 SL1O and SL1Q single board ............................................ .................................................. ........... 20 3.1.1 before upgrading to prepare workers for .............................. .................................................. ...................... 20 3.1.2 upgrade sequence ..................... .................................................. .......................................... 20 3.1.3 upgrade steps (using Navigator to load) .............................................. ............................ 20 3.1.4 Upgrade matters .............. .................................................. .......................................... 21 3.1.5 upgrade focus on examination of content ................................................ ............................................... 21 3.1. 6 the veneer FPGA load exception handling ........................................ ........................................ 21 3.2 SHLQ single board ..... .................................................. .................................................. .............. 22 3.2.1 before upgrading to prepare work for ........................... .................................................. ......................... 22 3.2.2 upgrade sequence .................. .................................................. .............................................
22 3.2.3 upgrade Step ................................................ .................................................. ............... 22 4 Data veneer upgrade instructions ............................................ .................................................. .............. 23 4.1 the ATM processing board .............................................. .................................................. ...................... 23 4.1.1 upgrade preparation work ................... .................................................. ................................. 23 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 3 of 43
61281792.doc Confidentiality: the internal public 4.1.2 upgrade sequence ....................................... .................................................. ................... 24 4.1.3 upgrade steps (use Navigator to load) ................... .................................................. ..... 24 4.1.4 database locked after processing method ................................. .................................................. ..... 26 4.2 of ET1 single board ........................................ .................................................. ................................. 28 4.2.1 upgrade preparation work ........ .................................................. ............................................ 28 4.2.2 upgrade along Preface ................................................. .................................................. A .............. 28 4.2.3 upgrade steps ......................... .................................................. .................................. 28 4.2.4 ET1 V1 features veneer upgrade to of ET1 V2, features veneer Some say out ........................................... 29 4.3 the EFS l level .............................................. .................................................. ....................... 30 4.3.1 upgrade preparation work ................. .................................................. .................................. 30 4.3.2 upgrade sequence ......... .................................................. .................................................. .... 30 4.3.3 upgrade steps (using the Navigator to load) ............................... ........................................ 30 4.3.4 upgrade steps (using the ToolKit tools load) .............................................. ................... 32 4.3.5 upgrade precautions .................. .................................................. ...................................... 35 4.3.6 upgrade focus on examination .. .................................................. ........................................... 35 4.4 EFS downgraded. .................................................. .................................................. .................. 36 4.4.1 downgrade before the preparatory work ....................... .................................................. ............................. 36 4.4.2 downgrade sequence .......... .................................................. ................................................. 36 4.4.3 downgrade steps (using the Navigator to load) ....................................... ................................... 36 4.4.4 downgrade steps (using the the ToolKit tool load) .. .................................................. ................... 37 4.5 single board software loading exception handling on .................... .................................................. ........................ 39 4.5.1 Question 1: single-board software loading is not successful .... .................................................. ................. 39 4.5.2: Upgrade AIU is not normal operation ................. .................................................. The ...... 39 4.6 Single Board FPGA load exception deal with the problem ........................... .................................................. ...... 40 4.6.1 Problem 1: the FPGA load is not a successful ............................ .................................................. ... 40 5 Other ................................................ .................................................. ................................... 40 5.1 5.2 the basis of the BIOS upgrade ............................................ .................................................. .................. 40 DIP Description ........................... .................................................. .............................................. 40 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 4 of 43 61281792.doc Confidentiality: the internal public Keywords: Keywords software upgrade Note downgrade sequence host software the Veneer software FPGA Extended BIOS Abstract: Unusual circumstances The OptiX 155622H (Metro 1000) software upgrade system introduced, including the upgrade sequence, each upgrade, check the matters before and after the upgrade, and finally gives the processing instructions in a variety of unusual circumstances. List of acronyms: Abbreviations list none. Reference list: a list of references: None. 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 5 of 43
61281792.doc Confidentiality: the internal public The OptiX 155622H (Metro 1000) product software upgrade instructions 1 Overview This document provides the OptiX Metro1000 mainframe products, extended BIOS data single board comes with the CPU can load the software upgrade, upgrade Note, exception handling is described. The type of software can be loaded: the OptiX Metro1000 product support online-loaded software includes host software, the expansion of the SCB board BIOS, FPGA, the board software that comes with the CPU data veneer, FPGAs, control logic, extended BIOS, ne.ini and so on. Can not load the software type or veneer: the software is integrated in the main control board, veneer, such as circuit boards, slip board. 1.1 upgrade tool Can the OptiX Metro1000 software Navigator or ToolKit to load, it is recommended that the field use the Navigator, 5.60 and above, the ToolKit the need ToolkitV100R002T09 and above; host software is recommended to use the Navigator to load; veneer can consider using the ToolKit to load software to improve efficiency . 1.2 upgrade required reading Veneer software supporting table "products matching table" upgrade instructions " 1.3 to upgrade the order Network: the network: the ring network is proposed in accordance with the main direction of Central-by-station chain network is recommended to upgrade from the first end station. Upgrading from near and far, This helps the analytical processing when an exception occurs, or facilitate the necessary circumstances to the scene to solve the problem. 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 6 of 43
61281792.doc Confidentiality: the internal public Network elements: the network element: a single board to the host software upgrade, the reset will not take the initiative to the veneer under, configuration, while the veneer software upgrades cause the reset will take the initiative to apply to host configuration, so the requirements to upgrade the host and then upgrade software to make the entry into force of the new host configuration in a single board. In the veneer: Veneer: the data comes with the CPU board veneer software upgrade to upgrade in the following order: control logic, the expansion of the BIOS, FPGA board software, ne.ini; Note ne.ini must finally add contained, the first four software loading order does not matter. 1.4 software access 1, in accordance with the supporting table in advance to obtain upgrade the software needed; in advance to back up online to run the equipment software. Each board version of the software from time to time update, it is recommended to the software on the server before each new implementation, upgrade, download the latest version of the software, at the same time to backup the current version of the software of the online operation of equipment. 1.5 upgrade process specification 1, a major upgrade in advance (at least 2 days) to the upgrade program is sent back to the company audit; controlled version is required to submit a version of the application for the flow of electrons. Upgrade should be the actual situation and the version to be upgraded the network use policies laid down in advance detailed upgrade plan in strict accordance with process specifications to act, a major upgrade activities must advance the program to technical operating specifications of the customer site, the version management system and company requirements the support of the Ministry for review. The SCB board software upgrades Preparatory work before the 2.1 upgrade The idea here is to do the preparatory work before the upgrade. (1) Check the network's run state, running state, you must use the command line or network data backup, network element database backup to the FDB, in order to enter the installation after a master reset exception 2011-09-27 Huawei confidential, unauthorized proliferation 7, 43 61281792.doc Confidentiality: the internal public Restore the data when the state, and recommended that the backup after the database; If the network element is the installation of state, look for reasons, to ensure that the business of network elements is normal, then use the command line or network data backup. (2) check the communication status of the network to protect all network elements connected properly, as far as possible the implementation of the principle of proximity to upgrade; If you need to upgrade through Ecc peer network element, first make sure that Ben Wang Yuan, and not through MUX single-side network element board the Ecc communication access, otherwise erase the host software will lead to the network element can not connect. (3) Check the SCB board hardware models, such as the SS42SCB board of the original load the 4.02.05.05 host, now want to upgrade to 4.02.06.41P02, it must be replaced for of SS43SCB and above the main control board can be
achieved. Description of use: the sys-get-hdver command can query the current hardware version of the control board (Note: here 43SCB): sys-get-hdver @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ Message from 0x000900c2 (9.0.194 590018) DEVICE: SS43SCB: SCB_PCB: SCB_EPLD: OHP_FPGA: METRO1000 SS43 SS43SCB.2 REV.A SS43SCB12100 SS43SCB09100 * 2001/07 / 17 09:54:30 STG_FPGA: SS43SCB10100 * 2002/09/18 16:06:26 Message from 0x040900c2 @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ (9.0.194 67,698,882) (Note: The following is the result of the query out 42SCB) : Sys-get-hdver @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ Message from 0x00090001 (9.0.1 589825) Device: SBS155A-42 OHP FPGA: Ver2.1 XCB FPGA: Ver3.0 STG FPGA: Ver1.3 PCB 2011-09-27
VER: Rev.D Huawei confidential, unauthorized proliferation 8, 43 61281792.doc Confidentiality: the internal public @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ Message from 0x04090001 (9.0.1 67698689) (4) record Benwang alarms and performance, such as abnormal alarm or performance that may affect the upgrade operation, the fault first exclude and then implementation of the upgrade, and record the alarm and performance after the upgrade is also easy to compare. (5) Check and record all network elements, multiplexing protocol state of the node parameters, protocol type, network multiplexing segment protocol is non-normal state, the host resumed a result of the upgrade may cause business interruption. (6) in proportion to ready by the board. (7) to confirm the version supporting the need to upgrade to an extended BIOS and FPGA, and the need to upgrade T2000 network version; using the command sys-get-nesoftver can query the current expansion BIOS version; Metro100043 the SCB extended BIOS and FPGA synthesis with packages (produced due to the special needs of the extended BIOS and FPGA version of separation, only for special purposes, described in upgrade mode 4), 44SCB the extended BIOS and FPGA version of separation before the upgrade, be sure to confirm the version of the supporting relations and the release notes.
2.2 upgrade order Need to upgrade to an extended BIOS and FPGA need to upgrade to an extended BIOS and FPGA, and then upgrade the host software.
2.3 upgrade step 2.3.1 using Navigator software to be loaded Loading method and the traditional host software loading. The IP address of the computer network port is set to the network elements in the same network segment directly connected lines and equipment, the "ETHERNET" port is connected or inter-network routing through the ECC to be loaded. Suggested that the software loaded using the Navigator, version 5.60 and above. Use: open the Navigator, choose the step-by-step: [Nesoft DownLoad the [NeSoft DownLoad], fill in the correct network ID [NE ID], software, type [Type], and software in the path [File] in the dialog box, then click [Start] load, the load is complete, there will be the relevant boxes: 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 9, 43 61281792.doc Confidentiality: the internal public 2.3.2 use the Toolkit loading software Step 1: Start the Toolkit, select the menu "software to load the Load SoftWare" -> "Load Network Element Software [Load NE SoftWare]". Step 2: Right-click on the "root", select "Add Network yuan [the Add the NE]" and fill out the appropriate information in the dialog box, and press the OK button. 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 10, 43 61281792.doc Confidentiality: the internal public Step 3: Select the new NE, and then press the ">>" button to add the new NE in the action list to the right side of the [Operation List]. Be to select the appropriate type of software [SoftWare the Type and the corresponding load the file [File] "Step 4: Click [Start]" load. Note 1. The host software is loaded, you need to select a file type for Nesoft or Auto; load an extended BIOS, you need to select a file type for Extbios or Auto; load the FPGA file, you need to select the file type Fpga or Auto. This is not selected and loaded using Navigator. Selected when the load is not the same. This is with the use 2011-09-27 Huawei confidential, unauthorized proliferation 11, 43 61281792.doc
Confidentiality: the internal public Two. Toolkit need V100R002 latest version. . Version of the latest version. 3. When you load the file using the Toolkit, do not pre-delete the file with the same name on the network element, Toolkit, will not automatically delete the existing file and then reload this is not the same with the same load when the load using Navigator. In addition, to select a file type to "Auto" and with a choice to load a number of different files. 2.3.3 host software upgrade procedure Parameters, see 2.5.2. 2.4 Upgrade Considerations Given here the host software upgrade Notes. (1) multiple network elements through a HUB to communicate to prohibit multiple network elements, upgrade, or it may appear abnormal HUB communication data overload. (2) the expansion of the master board BIOS communication ability is limited, therefore recommended that conditions permit (such as the host database capacity and structural changes), do two sets of hosts at the same time erase with load, and should be sequentially erase a upgrade set, otherwise the communication may result in the case of ECC status less abnormal. (3) reuse of the whole network segment protocol state normal circumstances, you can upgrade the host of a single network element; or the whole ring can be multiplexed segment agreement to stop all, and then at the same time upgrade the ring network element host software first manually stop before the normal start of the agreement, and finally unified by the network to start the whole multiplex section ring protocol. Taken to avoid at the same time upgrade the host of the adjacent network element, so that re-paragraph agreement from the start, and must be stopped before the agreement automatically start manual, and then unified manually start, otherwise it will lead to business interruption. (4) upgrade of multiple subnets, pay attention to the confirmation of the expansion of the network element ID and the need to load network element consistent. (5) Cfg-set-autoload/cfg-load-bdpara command a relatively large number of defects, in practice prohibit the application of this command. 2.5 each version upgrade instructions From the mainstream of history version to upgrade to this version uses a variety of upgrade method, you can upgrade all the historical version to the existing version of the list mode, and then introduced in every way. 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 12, 43 61281792.doc Confidentiality: the internal public 2.5.1 Optix Metro1000 mainstream host software upgrade summary table (under the table a prerequisite for the existing version of the complementary relationship between the right) Before the upgrade after upgrade after 43SCB 4.02.06.31 its to way a version of 43SCB 4.02.06.40 way 2 43SCB 4.02.06.40 3 edition manner (including a variety of P version) 43SCB with special needs only upgrade the expansion BIOS, do not upgrade FPGA version of the way on the 5th before 4.02.06.40 (excluding 4.02.06.40) to focus on supporting the relationship between the extended BIOS upgrade, do not use the BIOS and FPGA synthesis package, must rub the library to focus on supporting Extended BIOS upgrade relationship, and when you upgrade, do not use
the BIOS and FPGA synthesis package 4.02.06.41P02 Note describes the focus on the complementary relationship between the extended BIOS 43SCB with special needs only upgrade the expansion of the BIOS, do not upgrade the FPGA version of the way on the 4th version 44SCB all software versions 4.02.06.40 and after 4 Note: the earlier the host only supports SS42SCB, not support SS43SCB, support TDT features 4.02.06.X host can only use 43SCB need to replace the control board. : 4.02.06.40 following versions of the host software (not included 4.02.06.40) upwards upgrade the flash storage space allocation changes, so it is necessary to rub libraries in the BIOS for the re-division of the FLASH memory, this operation erase a database FDB0 and FDB1. : Other cases, the host software upgrade can not erase the database, but the downgrade are required to wipe the library. : Supporting all versions of the above-described expansion pass BIOS and circuit board supporting the case of ECC.
2.5.2 a variety of upgrade described in detail Note:
1, following a variety of upgrade, such as no special specified, the software or BIOS, load times are directly connected to the load time. 2: the erase command to delete all the two sets of host software; re-load the host software, loaded into NSF1, the system will automatically copy it to not load the NSF2; if the load to NSF2, the system does not copy not loaded NSF1.
An upgrade Step 1: upload network in the network configuration or the original command-line configuration file. Step 2: Use the navigator and want to upgrade the network connections, log on to network elements; Step 3: execution :erase //command to erase the existing host software, and takes 30 seconds to erase success will display the command line prompt, followed by the network element automatically restart; log in again after about 10 seconds of network element will display "Illegal the Bios Command; Step 4: Step 5: Execute : the e-all //command to erase all the databases, showed that after the success of Succeed to the Erase .... reset, took 70 seconds; (or the implementation of: e-db command to erase the database, erase, erase, the Wait .... erase successfully display the Erase Success, time-consuming 30s) Step 6: log in again net will show "Illegal the Bios Command"; Executive : e-biosfpga, command erase an extended BIOS and FPGA took two seconds, to erase the success "of Succeed to the Erase!"; Step 7: Extended BIOS loaded with navigator (select "NeSoft Download" interface "Type" select "BIOS"), pay attention to here is to extend the package is loaded in the BIOS and FPGA synthesis, supporting version to see the version of the supporting table, loaded successfully, there will be prompt box the emergence of the network element will automatically restart; Step 8: After about 5 seconds to log in again to the network element will display "Illegal the Bios Command; Step 9: Use the navigator to load the host software, select Nesoft1 load, load will be related to prompt box appears, after the success of the control board will automatically reset to start the host software after the upgrade; load took 90 seconds, software reboot consuming 70 seconds; Step 10: again, landing net use :sys-get-nesoftver //command to query the software version, make sure the upgrade was successful; Step 11: Use the network issued the original configuration file to download the original configuration or using the command line; Step 12: Using " :dbms-copy-all:drdb,fdb0; :dbms-copy-all:drdb,fdb1; //": command to back up the configuration data to the FLASH database.
2 upgrade step 1 steps: set out on using network configuration or the original command-line configuration file. Step 2: Use the navigator and want to upgrade the network connection, log on to network elements. Step 3: Use the command " :dbms-copy-all:mdb,drdb; :dbms-copy-all:drdb,fdb0, :dbms-copy-all:drdb,fdb1"//respectively, database backup to fdb0 and fdb1 ; Step 4: After execution :erase //command to erase the existing host software needs 30 seconds to erase successfully displays the command line prompt, and then network will automatically restart; about 10 seconds to log on again network element, will display "Illegal the Bios Command"; Step 5: Perform
:e-biosfpga //the command to erase an extended BIOS and FPGA, took 2 seconds to erase success "of Succeed to the Erase!"; Step 6: use the navigator to load the extension BIOS (select "NeSoft Download" interface "Type" select "BIOS"), pay attention to here is to extend the package is loaded in the BIOS and FPGA synthesis, supporting version to see the version of the supporting table, loaded successfully, there will be prompt box emergence of network elements will automatically restart; about 5 seconds to log in again to the network element will display "Illegal the Bios Command;
Step 7: Step 8: Use the navigator to load the host software, select Nesoft1 load loaded successfully, there will be prompt box appears, the control board will automatically reset to start the host software after the upgrade; load took 90 seconds, the software restart took 70 seconds; Step 9: Once again landing net with :sys-get-nesoftver //command to check the software version, make sure the update was successful; Step 10: Using :dbms-copy-all:drdb,fdb0; :dbms-copy-all:drdb,fdb1; command backup configuration data to the FLASH database upgrade Step 1: set out on using network configuration or the original command-line configuration file. : Step 2: Use the command " : dbms-copy-all: mdb, drdb; : dbms-copy-all: drdb, fdb0; : dbms-copy-all: drdb, fdb1", respectively, database backup to fdb0 fdb1 in. Step 3: Query the currently running host is which set, and the version of the current two sets of host : : the sys-get-curnesoft;// query the current host which set; : the sys-get-nesoftver;// queries two versions of the host. Step 4: erase is not running state that a host erased after the success of the command line prompt; : the network will automatically restart. About 90-120 seconds after the re-landing net, and then has been deleted host The set of software to reload the new host software (Note: the current running state of the host software is the first set, for example, the load interface Type options, select Nesoft2) loaded successfully, there will be the relevant boxes, and network element automatically restart; : the sys-erase-nesoft: "NSF2";// erase the second set of host software Step 5: after about 90-120 seconds, once again, landing net, the then the newly loaded host to switch to run: state : : sys-start-nesoft: "NSF2"; //switch host command (activation of a set of host-to-run state), the network element will automatically restart; Step 6: wipe and load another set of old host (process with Step 3) : : the sys-erase-nesoft: "NSF1"; Step 7: about 90-120 seconds after the landing net again, this time set the host to the first set of run: state : the sys-start-nesoft:"NSF1, then, the network element will automatically restart; Step 8: After about 90-120 seconds, once again landing net version of the query to identify the host: upgrade :sys-get- nesoftver; //query the two host versions. Step 9: Using :dbms-copy-all:drdb,fdb0; :dbms-copy-all:drdb,fdb1; : command backup configuration data to the FLASH database; upgrade Step 1: upload network in the network configuration or the original command-line configuration file. Step 2: Use the navigator and want to upgrade the network connection, log on to network elements. Step 3: Use the command " :dbms-copy-all:mdb,drdb; :dbms-copy-all:drdb,fdb0; :dbms-copy-all:drdb,fdb1;// respectively, database backup to fdb0 and fdb1 ; Step 4: execution: erase command to erase the existing host software needs 30 seconds to erase success will display the command line prompt, the network element will automatically restart; Step 5: After about 10 seconds to log in again network element, will show "Illegal the Bios Command";
execute: e-the bios command to erase the extended BIOS, took two seconds to erase success of Succeed to the Erase! "; Step 6: use the navigator to load the extension BIOS (select "NeSoft Download" interface in the "Type" choose "BIOS"), note here is the separation of the expansion BIOS of the FPGA with Set version to see the version of the supporting table, loaded successfully, there will be a prompt box appears, then the network will automatically restart; Step 7: After about 5 seconds to log on again network element will display "Illegal the Bios Command; Step 8: use the navigator to load the host software, Select Nesoft1 loaded, loaded successfully, there will be prompt box appears, the control board will automatically reset and start the host software after the upgrade; load took 90 seconds. restart 70 seconds of the time-consuming software; Step 9: Once again landing net use: sys - get the-nesoftver command to query the software version, make sure the upgrade was successful; Step 10: Using " :dbms-copy-all:drdb,fdb0; :dbms-copy-all:drdb, db1; : command backup configuration data to the FLASH database upgrade Step 1: upload network in the network configuration or the original command-line configuration file. Step 2: Use the navigator and want to upgrade the network connection, log on network elements; Step 3: execution: erase command to erase the existing host software, and takes 30 seconds to erase success will display the command line prompt, then net element will restart automatically; will display "Illegal the Bios Command; Step 4 :: about 10 seconds after landing net again, Step 5: Perform: e-all command to erase all the database after the success of Succeed to the Erase .. .. Reset, took 70 seconds; (or perform: the e-db command to erase the database, erase, erase, the Wait .... erase after the success of the Erase Success, time-consuming 30s) Step 6: Once again login network element, will show "Illegal the Bios Command"; Executive: e-the bios command to erase the Extended BIOS, took 2 seconds to erase the successful display of Succeed to the Erase! "; Step 7: Use the navigator to load the expansion BIOS (Select "NeSoft Download" interface "Type" select "BIOS"), pay attention to here is already separated FPGA extension of the BIOS, matching version, see the version of the supporting table, loaded successfully, there will be boxes the network element will automatically restart; Step 8: After about 5 seconds to log in again to the network element will display "Illegal the Bios Command; Step 9: Use the navigator to load the host software, select Nesoft1 loaded successfully load will then be prompt box appears, the control board will automatically reset to start the host software after the upgrade; load took 90 seconds, software restart took 70 seconds; Step 10: Network Element log in again to use: the sys- get-nesoftver command to query the software version, make sure the upgrade was successful; Step 11: Use the network to download the original configuration or using the command line of the original configuration file; 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 17, 43 61281792.doc Confidentiality: the internal public Step 12: Using " :dbms-copy-all:drdb,fdb0; :dbms-copy-all:drdb,fdb1; : command backup configuration data to the FLASH database. Focus on examination of the content after 2.6 upgrade Host software must be carried out after the upgrade the network running status and data set to be checked, here
only in the key project data collected compared to before the upgrade, do the following requirements: No. 1 2 3 4 Check Project Network to run the state network version check network alarms check network performance check operation command : cfg-get-nestate : the sys-get-nesoftver : ver : alm-get-curdata:0,0; //check the standard network element in running state NSF1, NSF2 currently running version must be consistent with no new abnormal alarm the performance can be reported to the normal performance value before the upgrade, no abnormal changes in the final full-ring network element multiplex section agreement in the normal state ring complex is set correctly segment the node parameters, SD switching switch and ask people to open the database more consistent :Per-get-curdata:0,0,perall,15m :Apsc-get-state: sysnum 5 Multiplexing segment protocol status check 6 Multiplexing segment parameters are correct :Apsc-get-para: sysnum :apsc-get-sdflag: sysnum :dbms-compare-all:drdb,fdb0; :dbms-compare-all:drdb,fdb1; :dbms-compare-all:mdb,drdb; :dbms-get-autobackup 7 Database consistency check 8910 Database automatically backup host and network management checks matching check with the user to confirm whether it is normal business after the upgrade Database automatically backup switch to open the network to be able to meet the minimum matching requirements of the business properly Check the version of the network management software With the user to check Recommend the use of the optical network operation analysis system to check the equipment running status, in order to check the upgrade to solve known issues before the upgrade, and upgrade new or left over after tips: before and after the upgrade. 2.7 host software loading exception handling 2.7.1 Question 1: host software can not be loaded [Describe problem] Huawei confidential, unauthorized proliferation 18, 43 2011-09-27 61281792.doc Confidentiality: the internal public
The host software can not be loaded [the cause of the problem] rub libraries before the upgrade failure. [Solution] delete the original host software, the new host can not successfully loaded, according to the following approach: 1) to confirm network communication status, if the DCN have a problem, or ECC communication state of instability, error, try repeatedly to load a few times to try to repeated loading is unsuccessful, you need to first solve the communication problem and then loaded. 2) re-check the hardware version of the SCB board, pay attention to software, hardware supporting relationship, such as not 4.02.06.41P02 host load to SS42SCB board. Ruled out the above problem, and then proceed as follows: 3) can try to reset the control board (: reset), after rebooting, re-load the host software. 4) Plug the control board, to be the master on-line re-load the host software. 8) Use the DIP method to erase data: SS43SCB :: dial code on the left dial 0xfa (11.11101 million), Master power will work in the BIOS status log on the network element directly connected line (IP address for the 129.9 .0.5) issued the erase command (see below), power-on re-load the host software; BIOS state Erase command is as follows: the state erase command is as follows :: the e-db: e-nsf1: the e- nsf2: e-all erase the database to erase the first set of the host to erase the second host to erase all of the host software and databases to erase an extended BIOS and FPGA : E-biosfpga, If the above method is still not resolved, replace the control board to reload. 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 19, 43 61281792.doc Confidentiality: the internal public LPU SBC software and FPGA upgrade business board Preparatory work before the 3.1.1 upgrade of of 3.1 SL1O and SL1Q veneer (1) need to make sure the veneer reign and all the veneer to be upgrade version of the FPGA. (Recommended to use the optical network operation analysis system to generate each board version of the report, and then one by one to confirm) 3.1.2 upgrade order Only to upgrade the FPGA. 3.1.3 upgrade steps (use Navigator to load) Upgrade steps (to SL1O for example): (1) start the Navigator login network element, use: sys-erase-bdfpga: 14, sl1o command to erase the existing the FPGA; erased after the success of the command line prompt (2) Upload FPGA: the make the use nesoft download, the type you want to select "BDFpga, the board position to select 14, the following: (3) loaded, SL1O to the automatic reset automatically start a new load FPGA work; 2011-09-27 Huawei confidential, unauthorized proliferation 20, 43 61281792.doc Confidentiality: the internal public (4): dm: 0x203a000 (query register command) to see if downloaded to the FLASH successfully returned a bunch of data that are 0x00 or 0xFF means no download is successful;: the dm: 0x2032000 (check register command) to see whether to load the FPGA successfully, 0x2032000 of the load after the success of the value of 0x11, 0x2032020 value of 0x01. Example: # 9-7: szhw [] [2005-11-26 12:11:59]>: the dm: 0x2032000 @ @ @ @ @ @ @ @ @ Message from 0x00090007 (9.0.7 589 831), 02.032 million 11 38 38 38 383 838 ... here to return to 11 means that the FPGA is loaded successfully
3.1.4 upgrade Notes Focus on examination after the 3.1.5 upgrade FPGA after the upgrade must be running status and data of the network settings check, here only in the key project data collected compared to before the upgrade, do the following requirements: 12 serial number, check the project board alarm to check the veneer performance check with the user to confirm the upgrade business is normal version of the FPGA core operating command: alm-get-curdata from: 0,0 inspection standards do not add exception warning the performance can reported normal, and the performance value compared to before the upgrade, there is no abnormal changes in the business often view version if need to upgrade your version of consistent : Per-get-curdata: 0,0, perall, 15m With the user to check: cfg-get-sl1fpgaver: 14 34 Tips: before and after the upgrade proposed use of the optical network operation analysis system to check on equipment operation status, to check the upgrade will fix the known issues before the upgrade, and whether there are new issues or problems left over after the upgrade. 3.1.6 Single Board FPGA load exception processing [Problem Description] FPGA loaded unsuccessful [cause of the problem] 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 21, 43 61281792.doc Confidentiality: the internal public , Version supporting two veneer is not reset [solution] in the process of upgrade veneer software Navigator has been deleted from the original the FPGA, the FPGA loads on, can be processed as follows: (1 whether supporting FPGA) check to be upgraded with a new FPGA, if you have supporting you can repeatedly load re-issued the FPGA, if unsuccessful, need next step: (2) hard reset the card (and pull the board is basically the same) , and then issued the FPGA, if unsuccessful, takes the next step: replace the veneer. Preparatory work before the 3.2.1 upgrade 3.2 SHLQ veneer (1) need to make sure the veneer reign, and all to be upgraded version of the veneer. (Recommended use of optical network running analysis system to generate a version of the statements of each board, one by one to confirm) 3.2.2 upgrade order Only to upgrade the board software; 3.2.3 upgrade steps Upgrades and veneer of this veneer is basically no difference, for the load method is briefly described as follows: 1) local upgrade using Navigator can be downloaded via email; remote with Navigator through the ECC channel load. 2), requires Navigator, 5.60 and above; 3) veneer SHLQ support Spanning Tree Protocol, and generally do not recommend customers use the spanning tree function, If you really must use the case, the engineer as soon as possible to contact technical support MAC address of the applicant to the company , please. 2011-09-27
Huawei confidential, the prohibition of unauthorized proliferation 22, 43 61281792.doc Confidentiality: the internal public 4), can be: (1) connected to run the network elements in the above single-board software loading window, first click on the "Login NE" button to log in the 5.60 version of the Navigator after the Login Ne direct download. ② If the main window of the above did not show SHLQ veneer, click the "Add Board" button to increase the veneer. The ③ choose SS4SHLQ03110T0 .. such a target file, click the "Start" button, the file is loaded. Data veneer upgrade instructions 4.1 ATM processing board pre 4.1.1 upgrade (1) need to make sure the veneer reign, and all to be upgraded version of the veneer. (Recommended use of optical network running analysis system to generate a version of the statements of each board, one by one to confirm) 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 23, 43 61281792.doc Confidentiality: the internal public 4.1.2 upgrade order Only to upgrade the board software; 4.1.3 upgrade steps (use Navigator to load) 1), delete the database: atm-dbms-clear-flag: drdb;: atm-dbms-clear-flag: fdb0;: atm-dbms-clear-flag: fdb1; If the upgrade did not clear before the database, two versions database structure, the upgrade is complete, will lead The AIU veneer into the database lock state (running lights flash slowly), and any data not written to the database, the veneer can not run normally, if you can not use database solutions below lock method to unlock, you can only change the board. So requirements: ATM upgrade must first delete the database. 2), use the command :: atm,-erase-nesoft: "NSF1" erase the original version. After the erasure of the old version of the software),: atm-reset; reset AIU board. 4) in the Navigator download window to download new software, the AIU software upgrade process is similar to the usual host software upgrade. 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 24, 43 61281792.doc Confidentiality: the internal public Shown above into the Download window after, NE ID to fill Benwang ID to Type to select Nesoft1, click Start to begin the upgrade, after upgrade: atm-ver version of the query in the File column select 4.07.02.10.hwx path , ensure the correct download. Note: The AIU board software functionally equivalent to a Master Control Software, all the ATM
service configuration are all stored in the the AIU single board, single board has its own database. Download software to fill in the actual network element ID in a Target Software Select Nesoft, the master will automatically distinguish between loaded SCB software AIU software. 5), upgrade to the new version, the upgrade is complete check the correct version. 6), issued a new configuration file, pay attention before the next hair configuration, use the atm-init command to initialize the board configuration, the check issued after the completion of network element data correctness and the Measurement command to check the ATM connection working condition, ensure business normal. 7), backup data libraries: atm-dbms-copy-all: mdb, drdb;: atm-dbms-copy-all: drdb, fdb0;: atm-dbms-copy-all: drdb, fdb1; Note: 1, if To upgrade the the AIU host and 155/622H host, please delete the the AIU host conduct 166/522H host upgrade, this phenomenon may occur after the upgrade Navigator can not access AIU AIU software can only be removed through the serial port, then AIU software is loaded. (Important) 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 25, 43 61281792.doc Confidentiality: the internal public 2, if you delete the host software NSF1, as well as the aiu board software, and then load the the aiu board software load on; only the first host software NSF1 loaded, then load the aiu-board software to loaded successfully. 4.1.4 database lock approach If not deleted before the upgrade AIU veneer AIU's ATM business database, then the veneer reset after the upgrade, the read data on a the AIU single board ATM database, the database structure and the V1 version of the database in V2 (4.07.02.10) different structures, the AIU veneer will be frequently reset, and ultimately lead to the database to enter protected mode (the phenomenon of slow the AIU veneer to run lights flash). Approach are as follows: the AIU database write protection mode approach [failure characteristics] 1, the AIU veneer running lights flash slowly (running lights green normal circumstances, the next second flash, slow flash about two seconds flash) . 2, the ATM database query AIU board: atm-dbms-get-pmode; returns the result as follows: the DBMS PROTECTION MODE SWITCH the STATE CUR_ABORTCNT enable the Total records: 1 # aiu: szhw these results you can see the database schema for the protection of state database write permissions for the close, can not be a normal backup of the database. [Fault reason when the veneer or the host to read the database data, due to changes in database structure or database with existing host database is not compatible, the host to the veneer repeatedly read the database, resulting in the frequent reset of veneer. Ten times when the reset, the the veneer host database, the database is set for the protection of state and close the write permissions for the database lock. protect WRITERIGHT PMODE_ABORTCNT close 10 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 26, 43 61281792.doc Confidentiality: the internal public [Solution] When the database into the write-protected, can be solved by following these steps: 1) to open the ATM database write permissions: atm-dbms-set-pmode: wrtright = open; the query the database protection mode, the DBMS PROTECTION MODE SWITCH STATE CUR_ABORTCNT enable 0 Total records: 1 2), delete the the ATM the
database drdb, the fdb: atm-dbms-The clear-flag: drdb;: atm-dbms-The clear-flag: fdb0;: atm-dbms-the clear-flag: fdb1; 3) Reset AIU: atm-the reset; query the database protection mode to restore to normal the DBMS PROTECTION the MODE SWITCH the STATE CUR_ABORTCNT enable the Total records: 1) the re-under configuration 5), backup ATM data library: atm-dbms-copy- all: mdb, drdb;: atm-dbms-copy-all: drdb, fdb0;: atm-dbms-copy-all: drdb, fdb1; 2011-09-27 Huawei confidential, unauthorized proliferation 27, 43 WRITERIGHT PMODE_ABORTCNT protect open 10 WRITERIGHT PMODE_ABORTCNT normal open 10 61281792.doc Confidentiality: the internal public 6), comparative data library: atm,-dbms-the compare-All: mdb drdb;: atm-dbms-the compare-All: mdb, fdb0;: atmdbms-the compare-All: mdb, fdb1; database normal backup of the words Comparison of the results should be consistent. 4.2 of ET1 before the 4.2.1 upgrade veneer preparations (1) need to make sure the veneer reign, and all to be upgraded version of the veneer. (Recommended use of optical network running analysis system to generate a version of the statements of each board, one by one to confirm) 4.2.2 upgrade order According to the order of the FPGA board software upgrade; 4.2.3 upgrade steps Upgrades and veneer of this veneer is basically no difference, for the load method is briefly described as follows: a local upgrade using Navigator can be downloaded via email; remote Navigator through the ECC channel to load. 2, needs Navigator, version 5.60 and above; for the 5.60 version of the Navigator after the Login Ne, the ADD in the ADD BOARD: 4 et1O "(for example: load ET1O), and then start the download, as shown in Figure: 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 28, 43 61281792.doc
Confidentiality: the internal public 4.2.4 of ET1 V1 features veneer upgrade of ET1 V2 features veneer Some explanations Online running the ET1 veneer (veneer software: 1.XX) are without a MAC address from of ET1 V1 upgrade to V2, the same hardware system used in the V1 and V2 veneer. only need to V2 features the board software upgrade to V1 veneer can (upgrade method and the ordinary single-version software upgrade) upgraded veneer on the second floor of the exchange function of ET1 V2, features a single board, the software will automatically generate a MAC address can not be used: AA-AA-AA-AA-AA-AA, then in addition to the spanning tree protocol is not available, the V2 features can be normal use, to Use the spanning tree protocol, you must first apply to the company apply for a MAC address, then use the following PTP commands sent to the single-board FLASH (brownout can be stored). : Ptp: 4,7 e, 0,0,0,0,25,06,0,6 of, mac address; / / mac input format: 11,22,33,44,55,66 generally do not recommend that customers use to generate tree If you really must use, engineers, contact technical support department as soon as possible to the MAC address of the application 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 29, 43 61281792.doc Confidentiality: the internal public Preparatory work before 4.3 the EFS upgrade 4.3.1 upgrade (1) need to make sure the veneer reign, and all to be upgraded version of the veneer. (Recommended use of optical network running analysis system to generate a version of the statements of each board, one by one to confirm) 4.3.2 upgrade order In accordance with the control logic, extended BIOS, FPGA, single-board software the, ne.ini order to upgrade; 4.3.3 upgrade steps (use Navigator to load) Upgrade steps: (1) check the version information of the veneer, use :: ptp: bid 12,10 (which bid for the relevant board-bit number) returns a hexadecimal number, select all the hexadecimal number, click on the mouse button, select the Hex to an ASCII, it will be hexadecimal number into a specific version information. From query to the PCB, BIOS, extended BIOS, FPGA version and the single-board software version information. Example: : Ptp: 3,12,10 cmd in 0: 03 12 10 50 43 42 20 20 20 20 20 20 56 65 72 73 69 6f 6e 20 3a 20 53 53 34 32 45 46 53 20 56 45 52 2e 43 0d 0a 42 73 63 42 49 4f 53 20 20 56 65 72 73 69 6f 6e 20 3a 20 32-2e 31 32 0d 0a 45 78 74 42 49 4f 53 20 20 56 65 72 73 69 6f 6e 20 3a 20 32 2e 31 32 0d 0a 53 6f 66 74 77 61 72 65 20 56 65 72 73 69 6f 6e 20 3a 20 32 2e 32 31 0d 0a 50 6c 61 74 66 6f 72 6d 20 56 65 72 73 69 6f 6e 20 3a 20 35 2e 30 30 2e 30 34 0d 0a 4c 6f 67 69 63 20 20 20 20 56 65 72 73 69 6f 6e 20 3a 20 28 55 32 29 31 32 30 28 55 33 37 29 32 30 38 0d 0a 55 63 6f 64 65 20 20 20 20 56 65 72 73 69 6f 6e 20 3a 20 31 2e 33 33 0d 0a 00 2011-09-27 Huawei confidential, unauthorized proliferation 30, 43 61281792.doc Confidentiality: the internal public PCB BscBIOS ExtBIOS Version: SS42EFS VER.C Version: 2.12 Version: 2.12 Software Version: 2.21 Platform Version: 5.00.04 Logic Ucode Version: (U2) 120 (U37) 208 Version: 1.33
According to the version number to confirm the already back up the veneer running version of the target file. (2) (1) operation version, select whether delete the original file operation, if it is 220 the following versions (including the 220 version) to upgrade to 221 or above (including the 221 version), you must first delete the original The veneer Software. Start navigator, navigator under delete the original veneer Software :: ethn-debug-enable: enable: ethndebug: bid, "test remove / ofs1/hwx/ss42efs10.dlb" and if you need to upgrade the target version and inquiries to The current versions are below the 220 (including 220), or more than 221 (including 221) version, delete the original veneer operation of the software from time to implement. Direct the operation of the following steps. (3) start the Navigator, click on the pop BDsoft Download window; (4) to be upgraded in the NE ID window, enter the network element ID, the ID office is required to enter the hexadecimal ID number, the NE extension, such as ID, basic ID is 10 network elements required to enter 0x9000a, the Navigator 5.60 and above can also be expanded ID-ID decimal, such as the extension ID, basic ID of network element 10, you can enter 9-10; (5) Click Login NE button, enter the corresponding password of szhw user login network, the Navigator will automatically obtain the network elements of each slot on the physical veneer and its version number (hexadecimal); (6) Click To upgrade a single board, then Software, File, select the type of software to be loaded (the single-board software, ne.ini Extended BIOS select veneer Software, the remaining choice "FPGA"), and then select the software you need to load from the hard disk Click Start to start loading the software. Description: Description: (1) is similar to the single-board FPGA and board software upgrade loaded without having to manually delete the original software, pay attention to the veneer of software files named *. Dlb, FPGA, and control logic file named *. pga, extended BIOS files named *. hwx. (2) all software loaded after a hard reset or plug veneer, business interruption. Hard reset veneer command-line command: ptp: bid, 40,0, which bid for a board position number. 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 31, 43 61281792.doc Confidentiality: the internal public 4.3.4 upgrade steps (using the tool to load ToolKit) Steps: (1) query veneer version information, use: (7) query the version information of the veneer, use :: ptp: bid for, 12,10 (which bid for the board-bit number) to return a set of hexadecimal select all hexadecimal number, click the right mouse button, select the Hex to an ASCII hexadecimal number is converted into a specific version information. From query to the PCB, BIOS, extended BIOS, FPGA version and the single-board software version information. Example: : Ptp: 3,12,10 cmd in 0: 03 12 10 50 43 42 20 20 20 20 20 20 56 65 72 73 69 6f 6e 20 3a 20 53 53 34 32 45 46 53 20 56 45 52 2e 44 0d 0a 42 73 63 42 49 4f 53 20 20 56 65 72 73 69 6f 6e 20 3a 20 32 2e 31 31 0d 0a 45 78 74 42 49 4f 53 20 20 56 65 72 73 69 6f 6e 20 3a 20 32 2e 31 32 0d 0a 53 6f 66 74 77 61 72 65 20 56 65 72 73 69 6f 6e 20 3a 20 32 0d 0a 50 6c 2e 38 30 61 74 66 6f 72 6d 20 56 65 72 73 69 6f 6e 20 3a 20 35 2e 30 30 2e 30 34 0d 0a 4c 6f 67 69 63 20 20 20 20 56 65 72 73 69 6f 6e 20 3a 20 28 55 32 29 31 32 30 28 55 33 37 29 32 31 30 0d 0a 55 63 6f 64 65 20 20 20 20 56 65 72 73 69 6f 6e 20 3a 20 31 2e 33 35 0d 0a 00 PCB BscBIOS ExtBIOS Version: SS42EFS VER.D Version: 2.11 Version: 2.12 Software Version: 2.80 Platform Version: 5.00.04 Logic Ucode Version: (U2) 120 (U37) 210 Version: 1.35 According to the version number to confirm the already back up the veneer running version of the target file. (2) (1) operation version, select whether delete the original file operation, if it is 210 the following versions (including the 210 version) to upgrade to 221 or above (including the 221 version. 2011-09-27 Huawei confidential, unauthorized proliferation 32, 43
61281792.doc Confidentiality: the internal public Version), you must first delete the original single-board software. Start navigator, navigator under delete the original veneer Software :: ethn-debug-enable: enable: ethn-debug: bid, "test remove / ofs1/hwx/ss42efs10.dlb" and if you need to upgrade the target version and the query to the current version are below 210 (including 210), or more than 221 (including 221) version, delete the original veneer operation of the software from time to implement. Direct the operation of the following steps. (3) Kai move ToolKit, click on "Single software load" button, right-click on the "root" add a network element, (4) fill in the Network Element ID: Determined, select the corresponding network element right-click and select "Login to network elements; (5) Select the network right click and select Query veneer, you can query the type of corresponding plate of veneer; If there is no query out can manually add the veneer: the selected network element right-click and select "add veneer input veneer board position: 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 33, 43 61281792.doc Confidentiality: the internal public Attention to the need to veneer the reign of the newly added veneer will appear as "unknown"; (5) Select the check box to upgrade veneer on the left, click the ">>" to add into the "action list"; Click "File" in the disk file to be loaded: (6) Click the "Start" to load; the completion of a file is loaded to wait for the "Start" button after the effective load the next file; need to pay attention to select the correct file type: single board software selection "Bdsoft / Extbios / Ini "Extended BIOS selection 2011-09-27 Huawei confidential, unauthorized proliferation 34, 43 61281792.doc Confidentiality: the internal public "Bdsoft / Extbios / Ini" PL215 choice, the Fpga "veneer logical choice," Fpga ", the ini file selection Bdsoft / Extbios, / Ini". (7) all the files loaded using the Navigator hard reset veneer or hand-swappable veneer; 4.3.5 upgrade Notes () Ne.ini must be loaded last, the first four files the order does not matter. (2) single-board software loading is complete, request access to the current board software version to ensure that the software is loaded successfully. Load after the end of the veneer running normal after inquiries, or check up may be the BIOS version of the software. Focus on examination after the 4.3.6 upgrade Board software and FPGA upgrade the network running status and data set to be checked, detailed project see the inspection instructions here only lists the key project data collected compared to before the upgrade, do the following requirements: No checks operation command to use the network: ptp: bid 12,10 1 version check check standard return results consistent with the need to upgrade your version (Note: ptp command returns a hexadecimal number, select the hex number, click the right mouse button, select the Hex to an ASCII, it will be hexadecimal number into a specific version information from the query to the PCB, the basic BIOS, extended BIOS version of the FPGA and board software version information): alm-get -curdata: 0,0 no new exception warning the performance properly reported, and the performance value compared to before the upgrade, there is no abnormal changes in the business 23
Veneer alarm check veneer performance checks with the user to confirm the upgrade after normal business : Per-get-curdata: 0,0, perall, 15m With the user to check 6 Recommend the use of the optical network operation analysis system to check the equipment running status, in order to check the upgrade to solve known issues before the upgrade, and upgrade new or left over after tips: before and after the upgrade. 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 35, 43 61281792.doc Confidentiality: the internal public 4.4 EFS downgrade 4.4.1 to downgrade the preparatory work before (1) need to make sure the veneer reign and all the target version to be downgraded. Through formal channels need to downgrade the version of the target; to confirm a single board to run the control logic, fpga, exbios, single board software, ne.ini version, and pre-reservations version of the backup, just in case downgrade unsuccessful can also restore the original version. 4.4.2 downgrade order In accordance with the control logic, extended BIOS, FPGA, veneer software, ne.ini the order, demotion; 4.4.3 downgrade steps (loading) using the Navigator Downgrade steps: (1) Check the version information of the veneer, use :: ptp: bid 12,10 (which bid for the relevant board-bit number) returns a hexadecimal number, select the hexadecimal number, click the mouse button, select the Hex to an ASCII, it will be hexadecimal number into a specific version information. From query to the PCB, BIOS, extended BIOS, FPGA version and the single-board software version information. Example: : Ptp: 3,12,10 cmd in 0: 03 12 10 50 43 42 20 20 20 20 20 20 56 65 72 73 69 6f 6e 20 3a 20 53 53 34 32 45 46 53 20 56 45 52 2e 43 0d 0a 42 73 63 42 49 4f 53 20 20 56 65 72 73 69 6f 6e 20 3a 20 32-2e 31 32 0d 0a 45 78 74 42 49 4f 53 20 20 56 65 72 73 69 6f 6e 20 3a 20 32 2e 31 32 0d 0a 53 6f 66 74 77 61 72 65 20 56 65 72 73 69 6f 6e 20 3a 20 32 2e 32-31 0d 0a 50 6c 61 74 66 6f 72 6d 20 56 65 72 73 69 6f 6e 20 3a 20 35 2e 30 30 2e 30 34 0d 0a 4c 6f 67 69 63 20 2011 the -09-27 Huawei confidential, unauthorized proliferation 36, 43 61281792.doc Confidentiality: the internal public 20 20 20 56 65 72 73 69 6f 6e 20 3a 20 28 55 32 29 31 32 30 28 55 33 37 29 32 30 38 0d 0a 55 63 6f 64 65 20 20 20 20 56 65 72 73 69 6f 6e 20 3a 20 31 2e 33 33 0d 0a 00 PCB BscBIOS ExtBIOS Version: SS42EFS VER.C Version: 2.12 Version: 2.12
Software Version: 2.21 Platform Version: 5.00.04 Logic Ucode Version: (U2) 120 (U37) 208 Version: 1.33 According to the version number to confirm the already back up the veneer running version of the target file. (2) (1) operation version, select whether delete the original file operation, if it is 221 above (including the 221 version) downgraded to 220 the following versions (including the 220 version), you must first delete the original The veneer Software. Start navigator, navigator under delete the original veneer Software :: ethn-debug-enable: enable: ethndebug: bid, "test remove the / ofs1/hwx/42efs10.dlb" If you need to downgrade the target version and inquiries to The current versions are below the 220 (including 220), or more than 221 (including 221) version, delete the original veneer operation of the software from time to implement. Directly carry out the operation of the following steps. (3) with a navigator for file loading, loading sequence and corresponds to the order in the upgrade exactly the same, exactly the same mode of operation, please refer to upgrade the description in the guidance. 4.4.4 downgrade steps (using the ToolKit tool to load) Downgrade steps: (1) Check the version information of the veneer, use :: ptp: bid 12,10 (which bid for the relevant board-bit number) returns a hexadecimal number, select the hexadecimal number, click the mouse Right-select the Hex to ASCII, it will be the hexadecimal number into a specific version information. From query to the PCB, BIOS, extended BIOS, FPGA version and the single-board software version information. Example: 2011-09-27 Huawei confidential, unauthorized proliferation 37, 43 61281792.doc: ptp: 3,12,10 Confidentiality: the internal public cmd in 0: 03 12 10 50 43 42 20 20 20 20 20 20 56 65 72 73 69 6f 6e 20 3a 20 53 53 34 32 45 46 53 20 56 45 52 2e 44 0d 0a 42 73 63 42 49 4f 53 20 20 56 65 72 73 69 6f 6e 20 3a 20 32 2e 31 31 0d 0a 45 78 74 42 49 4f 53 20 20 56 65 72 73 69 6f 6e 20 3a 20 32 2e 31 32 0d 0a 53 6f 66 74 77 61 72 65 20 56 65 72 73 69 6f 6e 20 3a 20 32 0d 0a 50 6c 2e 38 30 61 74 66 6f 72 6d 20 56 65 72 73 69 6f 6e 20 3a 20 35 2e 30 30 2e 30 34 0d 0a 4c 6f 67 69 63 20 20 20 20 56 65 72 73 69 6f 6e 20 3a 20 28 55 32 29 31 32 30 28 55 33 37 29 32 31 30 0d 0a 55 63 6f 64 65 20 20 20 20 56 65 72 73 69 6f 6e 20 3a 20 31 2e 33 35 0d 0a 00 PCB BscBIOS ExtBIOS Version: SS42EFS VER.D Version: 2.11 Version: 2.12 Software Version: 2.80 Platform Version: 5.00.04 Logic Ucode Version: (U2) 120 (U37) 210 Version: 1.35 According to the version number to confirm the already back up the veneer running version of the target file. (2) (1) operation version, select whether delete the original file operation, if it is 221 above (including the 221 version) downgraded to 210 the following versions (including the 210 version), you must first delete the original The veneer Software. Start navigator, navigator under delete the original veneer Software :: ethn-debug-enable: enable: ethndebug: bid, "test remove the / ofs1/hwx/42efs10.dlb" If you need to downgrade the target version and inquiries to the current version are below 210 (including 210), or more than 221 (including 221) version, delete the original veneer operation of the software from time to implement. Directly carry out the operation of the following steps. (3) ToolKit to start, load the old version of the control logic, fpga, expansion of the bios, veneer software, ne.ini files, identical to the description of the steps and precautions and upgrade, as described in reference to upgrade 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 38, 43 61281792.doc Confidentiality: the internal public 4.5 single board software loading exception processing 4.5.1 Question 1: Veneer software loaded unsuccessful
[Problem Description] veneer software loaded unsuccessful [the cause of the problem] a single-board version was not complete, snowboarding is not reset [solution] upgrade the board software, if Navigator has been deleted from the original board software can not load the new board software, according to the following steps for processing: (1) Check to be upgraded veneer with the new board software supporting, if it is supporting, you can repeatedly load reissued board software, if unsuccessful, take the next step: (2) hard reset the card (and pull the board is basically the same), and then issued a single-board software, if unsuccessful, need next step: replace the veneer solution. 4.5.2 Question 2: After the upgrade AIU not work properly [Description] AIU upgrade not function properly after [the cause of the problem], did not perform the initialization problem; 【Methods】 Navigator login, use: atm-init initialization veneer; If the above methods can not solve the problem, you need to replacement veneer resolve. 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 39, 43 61281792.doc Confidentiality: the internal public 4.6 Single Board FPGA load exception processing 4.6.1 issues: the FPGA loaded unsuccessful [Problem Description] FPGA load unsuccessful [the cause of the problem], version is not complete, snowboarding is not reset [solution] upgrade the board software, if Navigator has been deleted from the original the FPGA, the new FPGA plus contained not be processed as follows: (1) Check of the FPGA to be upgraded and new FPGA supporting, if it is supporting, you can repeatedly load re-issued the FPGA, if unsuccessful, need next step: ( 2) hard reset the card (and pull the board is basically the same), and then issued the FPGA, if unsuccessful, need next step: replace the veneer solution. 5 Other 5.1 Basic BIOS upgrade The basis of the BIOS can not be online to load, if you need to upgrade to replace the BIOS chip, or use special tools to the scene to load. Under normal circumstances the basic BIOS do not need to upgrade, upgrade to an extended BIOS can. This version of the BIOS information only of production, technical support do not need to upgrade. 5.2 DIP Description Old DIP: 16 DIP switch 4 on the left for debugging / running state control switch 12, the right side of the DIP switch to the network element ID, are left for the high-control switch: 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 40, 43 61281792.doc Confidentiality: the internal public 0 - debug state when the ID is also allocated for the self-test for the 0:00, the others are playing open WatchDog running state; 1 - Standalone debugging state; - serial access debug state; 3 - Ethernet port access; 4 - Turn off WatchDog running state; 5 - BIOS running state (55 states); new DIP way: (1) 16 DIP switches, network ID, with only different from the previous 12, the legitimate range for 1 ~ 0xEFFF; ID ① The network element 16 DIP can not be both 0, the value of the DIP to retain value; ② network elements up to four DIP can not be both a DIP value 0xF000 to 0xFFFF for retention value; ③ network element 8 DIP can not be all one or at the same time zeros, that is allocated code value 0xXX00 0xXXFF retention; (2) When a maximum of four 1:00, the network element to enter the special status specific state is decided by the high eight DIP switches, the right of the 8 DIP network element ID, on the left 8
the following meanings: 0xFF - When the ID is also allocated for the self-test for the 0:00, others are Close WatchDog running state; 0xFE - Standalone debugging state; a 0xFD - serial access debug state; 0xFC - Ethernet port access debug state; 0xFB - Turn off WatchDog the running state; 0xFA - BIOS running state (55 states ); A. Specially formulated to be compatible with the previous BIOS, extended BIOS, the following complementary relationship between the table: Old base this BIOS SS43SCB BIOS - 110 to the previous version (this version) 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 41, 43 61281792.doc Confidentiality: the internal public Old and the new basic BIOS extended BIOS expansion BIOS After SS43SCB BIOS - 120 version (this version) SS43SCB Extended BIOS - 433 the previous version (this version) SS43SCB Extended BIOS - 434 later (including this version) Old host software host software SS43SCB: SS43SCB: NE4020603, NE4020604, NE4020610 NE4020620 later versions (including this version) Two. SS43SCB basic BIOS, extended BIOS, the host software supporting the use of relations as follows: Old base this BIOS Old expansion of the BIOS The old host software Debug state, 55 states run the state to use the old DIP way to identify the host software up to 12 network element ID The old basic BIOS Old expansion of the BIOS New host software Debug state, 55-state operating state of the old dial mode identification, the host software up 16 Network Element ID The old basic BIOS New Extended BIOS
The old host software 55 states: does not recognize, can not enter debug state: old DIP way to identify the running state: the old dial mode identification, host software up to 12 network element ID Old base this BIOS New Extended BIOS New host software 55 states: does not recognize, can not enter debug state: old DIP way to identify the state of the running: Use the old DIP 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 42, 43 61281792.doc Confidentiality: the internal public Way to identify the host software up 16 new base of the Network Element ID This BIOS version is only compatible with the new extension to the BIOS and host software, debug state, 55-state running state to use the new DIP way to identify 3. When SS43SCB only base the BIOS does not extend to the BIOS, and host software supporting the use of the relationship as follows: the old BIOS old host software debugging state, 55 states, state run using the old dial mode to identify the old and the new host of the basic BIOS software debugging state, 55 state, the state run old dial mode identification, the host software up to 16 Network Element ID BIOS only compatible with the new host software, debugging state, 55 states run the state to use the new DIP way to identify the 2011-09-27 Huawei confidential, the prohibition of unauthorized proliferation 43, 43
Original Chinese text:
方式识别， 主机软件起来后使用 16 位网元 ID 新基本 BIOS 只兼容新扩展 BIOS 和新主机软件，调试态、 55 态、运行态使用新拨码方式识别 Contribute a better translation
