Testing Directional Overcurrent Relays From Valence

4/12/2016

Testing D ir ecti onal Over cur r ent Rel ays fr om Val ence

Home » Home » Testing Directional Overcurrent Relays

Search

In the previous post about Directional Overcurrent relay (67) testing ( Finding the Direction in Directional Overcurrent Relays), Relays), we reviewed Directional Overcurrent Overcu rrent protection from a system perspective to enhance

Search...

the descriptions in The Relay Testing Handbook: Principles Prin ciples and Practice or The Relay Testing Handbook #1: Electrical Fundamentals for Relay Testing. Testing . We’ll be looking at Directional Overcurrent relays from a testing perspective in this post.

TechTalk Categories

Successful Directional Overcurrent tests have three parts: 1. Your current must be above the pickup setting.

Announcements (28) Announcements (28)

2. Your current must be in the correct direction.

Ask Chris Chris (20)

3. You must have a polarizing signal.

Electrical Basics Basics (19)

A traditional r elay tester, or automated testing software, will often apply a test scenario sc enario like the following:

From Other Testers (16) Testers (16) High Voltage Testing ( Testing ( 4) Relay Elements Elements (14) Relay Testing Techniques Techniques (21) The Relay Testing Handbook #4: Creating and Implementing Relay Test Plans ( Plans ( 1) Videos (14) Videos

Subscribe for Updates

Channel

Magnitude

Angle

Instruction

Ia

> Pickup setting

0° (default)

Raise until pickup

Subscribe to our mailing list and receive a free book preview, automatic updates, and special offers Email Address

This test plan may work depending on the sophistication of the relay, but there’s a pretty good chance that the pickup tests will work, and the timing test will fail. In this scenario, you might get frustrated and start disabling the directional function, or start looking for the non-directional relay definitions so you can map

I want updates regarding:

them to a test output. Let’s take a closer look at your test plan before you, or your test software, head down

Monthly Updates about Everything

that path.

New Blog Posts and Videos

https://r el aytr aini ng.com/testing- di r ecti onal - over cur r ent- r el ays/

1/8

4/12/2016

Testing Directional Overcurrent Relays from Valence

Based on the drawing of your test plan, it looks like you’ve met the first two criteria for a successful

New Training Handbooks Only

Directional Overcurrent test:

New Online Training Courses Only

1. The current is greater than the pickup setting. 2. The current is in the tripping direction. (Not in the shaded area) But do you have a polarizing signal?

New Hands-On Training Classes Only

Sign up for Updates

Testing Directional Overcurrent Relays That Use Phaseto-Phase References Imagine that I asked you for directions to your favorite restaurant after dark. You could give me directions

Contribute to TechTalk

like, “If you head north for ten blocks and then east for three blocks, you’ll find the best BBQ in the county.” Your directions are perfect, but I’ll be hungry until I find a compass or someone to give me a reference like, “North is that way”. However, if you said, “Turn right for ten blocks and then turn right for three more blocks”, I’ll be eating the best BBQ in no time. Directional relays need a reference to work correctly, and that reference is called the polarizing signal. The Directional Overcurrent element needs a polarizing signal to operate reliably; otherwise anything could happen depending of the sophistication of the relay. Most electro-mechanical relays, and GE relays like the one from The Relay Testing Handbook example, use the phase-phase voltage from the two un-faulted phases as a polarizing signal. You could drive yourself crazy trying to figure out how to apply the test and phasor diagrams from older relay manuals to modern test-sets.

Or you can test all relays that use the un-faulted voltages as a polarizing signal by simply applying threephase balanced voltages as shown in this phasor diagram from the previous post. We added the B-C phase-phase voltage to the drawing, which is the polarizing voltage this style of relay uses.

https://relaytraining.com/testing-directional-overcurrent-relays/

2/8

4/12/2016


If we rotate the standard phasor diagram by 90° and add the same labeling used by the relay bulletin drawings, we can see that simply adding voltage will allow us to successfully test every relay of this type.

Channel

Magnitude

Angle

Instruction

Ia

> Pickup setting

0° (default)

Raise until pickup

Va

Nominal V

0°

Vb

Nominal V

-120°

Vc

Nominal V

120°

Testing Directional Overcurrent Relays That Use Negative Sequence References Unfortunately, not every relay uses phase-phase voltages as a polarizing signal. Some relays use the negative sequence voltage as the polarizing signal. Negative sequence voltage can be simplified to mean unbalanced voltage (You can get more information in the Sequence Components section of The Relay Testing Handbook: Principles and Practice or The Relay Testing Handbook #1: Electrical Fundamentals for Relay Testing). Are the voltages unbalanced in the previous test plan? You can tell by graphically adding the three voltages together, or with the negative sequence formula.

The negative sequence, or unbalance voltage, is zero in a balanced system. Therefore, our previous test plan will not have a polarizing signal on relays that use negative sequence polarizing. We can fix this problem by thinking about what happens during a phase-to-ground fault. What happens to the faulted voltage? The faulted voltage will drop; how much it drops depends on


3/8

4/12/2016


the severity of the fault. The worst possible fault would drop the fault voltage to near zero, but most faults won’t be that severe. We can cut the faulted voltage in half to simulate a phase-to-ground fault. What happens to the faulted current? The faulted currents will jump to a higher value, and we know from the relay settings how much current we need for the relay to detect a fault. Set the fault current at least 110% of the relay’s pickup setting. What happens to the other voltages and currents that aren’t faulted? They would change slightly during a real fault, but you would need some modelling software to figure out how much. We can assume that they don’t move, like textbooks do, for testing purposes. If we alter our test plan to better simulate a fault, it would look like the revised plan below. Channel

Magnitude

Angle

Instruction

Ia

> Pickup setting

0° (default)

Raise until pickup

Va

One-half V

0°

Vb

Nominal V

-120°

Vc

Nominal V

120°

A plan to Test any Directional Overcurrent Relay Now our Directional Overcurrent (67) test plan looks like the following drawing where we start with the raw currents and voltages, calculate the non-faulted phase-to-phase voltage, and plot the operating current and polarizing signal, which in this case is VBC. This test plan has a good chance of being successful because we have an operating signal and a polarizing signal.

These drawings look at the same test plan for a Directional Overcurrent (67) element that uses negative sequence voltage. We start with the raw currents and voltages, then calculate the negative sequence voltage, and then plot the operating current and polarizing signal (V2). This test plan has a good chance of being successful because we have an operating signal and a polarizing signal.


4/8

4/12/2016


We appear to be in good shape for most Directional Overcurrent (67) applications. However, there will be times when this test plan will not work. What are the odds that a phase-to-ground fault will be 100% resistive? The answer is never. Actually, there are almost no purely resistive systems as we discussed in the previous article, so our test current at zero degrees can cause problems, especially near generation systems like wind farms that can have crazy characteristics or very high voltage (>115kV) applications. Some relays have an operating characteristic like the following picture:

Notice that our test current is right on the edge of the reverse direction. This means that it is a coin toss whether the relay will operate or not. We can ensure the relay always operates by setting the faulted current to a fault angle that would happen in the system. You can choose a good fault angle using one of these methods: Most modern relays have a positive sequence angle setting that defines the expected fault angle. Set the fault angle to that setting. If you have a good understanding of fault characteristics, you could guess the fault angles. A very high voltage sy stem (>115kV) will have a characteristic near 90 degrees, so you could safely choose a fault angle of 87°. A high v oltage sys tem (>69kV) will have a fault angle closer to 75°. A distribution system (>34kv) will have a fault angle cl oser to 60°. A medium voltage system will have a fault angle cl oser to 45°. You can never go wrong with a fault angle of 60° or 75°. This is what electro-mechanical relays used because their options were limited and they needed a good average. Our test will work for all common characteristic angles if we modify it to include the phase angle during a fault. Channel

Magnitude

Angle

Instruction

Ia

> Pickup setting

75° (or fault angle)

Raise until pickup

Va

One-half V

0°


5/8

4/12/2016


Vb

Nominal V

-120°

Vc

Nominal V

120°

Directional Overcurrent Relay Test Plan Summary Testing Directional Overcurrent (67) elements is almost as simple as testing standard Overcurrent (50/51) elements as long as you properly simulate a fault. I used to occasionally run into problems when testing Directional Overcurrent (67) elements using traditional testing techniques. I would spend a lot of unnecessary time trying to figure what went wrong as I said to myself, “I know I’m doing it right, why won’t this relay work right!!!” Now I always follow these steps before running any test: Connect all currents and voltages Choose the fault type to apply Apply nominal balanced three-phase voltages Cut the fault voltage in half Raise the fault current more than 110% of the pickup setting Make sure the fault current lags the fault voltage by the fault angle or 75° Modern testing equipment makes this easy, which means you can spend more time understanding the application so you can become a true relay testing craftsman. Please like and share this post if you found it useful. It helps us get noticed, which means we can post more free content. Add your comments for Directional Overcurrent relay (67) testing i n the comments section, s tart a new topic by becoming a TechTalk Contributor , or you can ask me questions about other topics with the Ask Chris form.


6/8

4/12/2016


Happy Testing! Share the Knowledge! LinkedIn 37

Facebook

Twitter

Google+ 2

Print 29

E-mail 6

Filed Under: Ask Chris, Featured, Relay Elements, Relay Testing TechniquesTagged With: Directional Overcurrent (67)

About Chris Werstiuk Chris is an Electrical Engineering Technologist, a Journeyman Power System Electrician, and a Professional Engineer. He is also the Author or The Relay Testing Handbook series and founder of Valence Electrical Training Services. You can find out more about Chris here.

Add Your Question or Comment: Your email address will not be published. Required fields are marked * Comment

Name *

Email *

− three = 2

Post Comment

SUBSCRIBE TO OUR MAILING LIST

OUR MOST RECENT POSTS

CONTACT US

Email Address *

A New Hands-On Advanced P rotective Relay

You can contact us using our online form or:

Testing Training Class has been Scheduled in Detroit, MI I want updates regarding: *

Valence will be at the NETA PowerTest 2016 Conference in Fort Worth, TN

Monthly Updates about Everything New Blog Posts and Videos Only New Training Handbooks Only

Where Should We Hold the Next Hands-On

Valence Electrical Training Services 7450 W. 52nd Ave., Unit M #330, Arvada, CO 80002 Phone: 303.250.8257 [email protected]

Relay Testing Training Class?


7/8

4/12/2016


New Online Training Courses Only

SEARCH THIS SITE

CONNECT WITH US:

New Hands-On Training Classes Only

      

Search...

Subscribe Now!

ONLINE TRAINING

TESTING HANDBOOK

HANDS-ON TRAINING


ELECTRICAL RESOURCES

ABOUT VALENCE

ONLINE STORE

8/8

Testing Directional Overcurrent Relays From Valence

Recommend Documents