ASME Code Section 8 The ASME Code Section 8 is construction code for pressure vessel and covers design, manufacturing and pressure vessel inspection and testing in manufacturing shop. This Code section addresses mandatory requirements, specific prohibitions, and non-mandatory guidance for Press. Vessel Materials, design, fabrication, examination, inspection, testing, certification, and pressure relief. This article describe you different subsections and provides guidelines to you for using and application of this code. For ASME Code Section 8 s cope and boundaries review Pressure Vessel Definition article.
You may know ASME Code Section 8 has three divisions. The Division 1 covers pressure up to 3000 psi, the Division 2 has alternative rule and covers up to 10,000 psi and Division 3 can be used for pressure higher than 10,000 psi. Hierarchy of Standard 1. Law and Regulation at Location of Installation Mandatory application of ASME pressure vessel code is determined by rule and regulation at location of installation. For example if you are living in the state of Minnesota the application of ASME Code for construction and stamping is mandatory in your location but if you are living in the state of South Carolina it is not mandatory.
2. ASME Boiler and Pressure Vessel Code The next item in this hierarchy is ASME Code itself, the ASME Code generally is divided in three groups as following Group 1: Construction Codes Some of them are; Section VIII for pressure vessel, Section I for Power Boiler, section III for Nuclear Power Plant and Section IV for heating Boiler Group 2: Reference Codes These are the codes which are referenced from construction codes as explained in group 1. The ASME Section IX for welding and Section V for Non Destructive Testing are in this Group. For example ASME Code section VIII for welding requirement such as WPS (Welding Procedure Specification), PQR (Procedure Qualification Record), Welder Performance Qualification and etc. refer you to ASME Section IX. Group 3: In-Service Codes These are the codes for in-service Inspection after placing the equipment into service. The ASME Section VI for heating boiler and Section VII are from this group. 3. National Board Inspection Code(NBIC): We have assigned a separate article for NBIC, but as require for this article, NBIC making certification for ASME Authorized Inspectors also certifying R stamp for Repair services for stamped pressure vessels. ASME Code Section 8 Content: See following Fig, it shows ASME Code Section 8 Content:
This section is divided into three Subsections, Mandatory Appendices, and Nonmandatory Appendices. Subsection A consists of Part UG, covering the general requirements applicable to all pressure vessels. Subsection B covers specific requirements that are applicable to the various methods used in the fabrication of pressure vessels. It consists of Parts UW, UF, and UB dealing with welded, forged, and brazed methods, respectively. Subsection C covers specific requirements applicable to the several classes of materials used in pressure vessel construction. It consists of Parts UCS, UNF, UHA, UCI, UCL, UCD, UHT, ULW, and ULT dealing with carbon and low alloy steels, nonferrous metals, high alloy steels, cast iron, clad and lined material, cast ductile iron, ferritic steels with properties enhanced by heat treatment, layered construction, and low temperature materials, respectively. For example if you need to manufacture a pressure vessel with SA 516 Gr.70 material (Carbon Steel), then you need to meet the marked items in above Fig. Please note ASME Code Section 8, does not provide you fabrication tolerances except of misalignment and weld reinforcement. For example for nozzles orientation, projection, elevation and other required tolerances there are no values in the code and you may refer to pressure vessel handbooks for such information. Review the Pressure Vessel Dimension Inspection article for such tolerances. If you review ASME Forward statement it clearly says “The Code does not address all aspects of construction activities and those aspects which are not specifically addressed should not be considered prohibited.” In continue says “The Code is not a handbook and cannot replace Education, Experience, and the use of engineering judgments.” For example ASME Code Section 8 Div 1 in UG-28 mandating all loading to be considered in pressure vessel design, but the method for calculation of all of them have not been addressed. For example the formula for wind, or earthquakes not provided in the ASME Code Section 8 and these items and other similar loading need to be designed by information provided in pressure vessel handbooks. For ASME pressure vessel manufacture certification as well as Authorized Inspection Agency certification Review the Pressure Vessel Certification article.
What is the Summary of Important Points in ASME Code Section 8 ? 1. ASME Code Section 8 edition is issued once in 3 years and addenda, once a year – year – both on 1 July. Edition and addenda become effective on 1st January of next year (i.e., 6 months after issue). 2. Thickness of cylindrical shell t = PR/(SE-0.6P) + C 3. Longitudinal weld is more critical because it is subjected to double the stress than Circ. Weld. 4. “Weld joint categories” A, B, C, D – are based on joint locations in the vessel and stress levels encountered. “Weld Types” (type 1, 2, 3, etc.) describe the weld itself. 5. Depths of 2:1 Ellip. and hemisph. heads are D/4 and D/2 respectively. (D= Head diameter.) 6. Weld Joint categories: Category A: - All longitudinal welds in shell and nozzles. - All welds in heads, Hemisph-head to shell weld joint Category B: - All circumferential welds in shell and nozzles - Head to shell joint (other than Hemisph.)
Category C and D are flange welds and nozzle attachment welds respectively. 7. Weld Types: Type 1: Full penetration welds (Typically Double welded) Type 2: Welds with backing strip Type 3: Single welded partial penetration welds Type 4, 5 and 6: Various Lap welds (rarely used) 8. For full penetration welds (type 1): Joint efficiency, E = 100%, 85%, 70% (For the radiography = Full, Spot, Nil respectively) 9. Radiography marking on name plates (typically for Type-1 welds) RT-1: (E=1) All butt welds – welds – full length radiography RT-2: (E=1.0) All Cat. A Butt welds Full length, Cat B, spot RT-3: (E=0.85) Spot radiography of both Cat A and B welds RT-4: (E=0.7) Partial/No radiography 10. For Welded Heads for E=1, all welds within the head require full length radiography (since they are all Cat. A welds) 11. For seamless heads, E=1, If a) head to shell weld is fully radiographed (if Cat. A), and at least spot radiographed (if Cat. B) 12. Compared to Cylindrical shell, thickness of 2:1 Ellipsoidal head is approx. same as shell, Hemisph. head approx. half and Torisph head is 77% higher. 13. MAWP is calculated for: Working condition (Hot & Corroded). Vessel MAWP is always taken at the Top of the Vessel and is lowest of all part MAWPs adjusted for static pressure. 14. Hydro-Test is Standard Pressure test on Completed Vessels. Hyd. Test Pr. = 1.3 x MAWP x stress ratio Insp. Pressure (hydro) = test pr. / 1.3 Min. Test temp. = MDMT + 30°F Max. Inspection temp. = 120°F 15. Pneumatic test is performed if hydro is not possible due to design or process reasons. Prior to the test, NDT as per UW50 is mandatory. Pneumatic test pressure = 1.1 x MAWP x stress ratio, Pressure should be increased in steps (Total 6). 1st step – step – 50% of test pressure 2nd to 6 step – step – 10% of test pressure Insp. Pr. (pneumatic) = test pressure /1.1 16. Pressure gauge range should be about twice the test pressure. However, in any case it shall not be lower than 1.5 times and not higher than 4 times the test pressure. 16. Vessel MAWP represents the maximum safe pressure holding capacity of the vessel. Vessel MAWP is measured at topmost point. And is lowest of vessel part MAWPs, adjusted for hydrostatic head. 18. For vertical vessels, hydrostatic pressure caused due to liquid with specific gravity = 1, 1ft of height = 0.43 psig. Or 1 mtr of height = 0.1 Bar 19. Total pressure at any point of Vertical vessel is given by: Total Pr. = Vessel MAWP + h x 0.433. (h = height from top in ft.) 20. If part MAWP and elevations are known, Vessel MAWP can be calculated by the deducting hydrostatic head from part MAWP. 21. Ext. Pressure is worked out on basis of Geometric factor A (which depends on L/Do and Do/t ratios) and factor B (depends on A, ) Allowable Ext. Pressure, Pa = 4B/(3(Do/t)) 22. For values of A falling to left of material line in the material chart: Pa = 2AE/(3(Do/t)) 23. Name plate shows The Code stamping, MAWP, design temp., MDMT, and Extent of Radiography. 24. ASME materials (SA) shall be used for code stamped vessel fabrication instead of ASTM (A) materials. 25. Reinforcement pad is not required, if the size of finished opening is (UG 36) 2-3/8” for all thicknesses of vessel Not exceeding 2-3/8” 3-½”, if vessel thickness is ≤ 3/8‟‟ Not exceeding 3-½”, 26. Reinforcement pad with OD = 2d and thk = vessel thk is always safe (d = diameter of finished opening) 27. Reinforcement limit along vessel wall = 2d 28. Reinforcement limit normal to vessel wall = smaller of 2.5 t or 2.5 tn 29. In reinforcement pad calculations, credit can be taken for area available in shell and nozzle. 30. Fillet weld throat dimension = 0.707 x leg of weld 31. Adequacy of weld sizes shall be checked as required by UW-16. The nozzles construction shall be one of the Code acceptable types. 32. The maximum permitted ovality tolerance (D max – max – D min) shall not exceed 1% of nominal diameter of vessel. If there is opening, then the tolerance can be increased by 2% x d (d = diameter of opening) if measurement is taken within a distance of „d‟ from axis of opening. 33. The mismatch tolerances and the maximum allowable weld reinforcement is more strict on longitudinal welds compared to circumferential welds (UW-35). 34. Principle of reinforcement:
Area removed = Area compensated. Compensation area shall be within reinforcement limits. 35. For use as pressure parts, the plates shall be fully identified. Maximum permitted under tolerance on plates is 0.01” (0.3 (0.3 mm) or 6% of ordered thickness, whichever is less. 36. All welding (including tack, seal, etc.) shall be done using qualified procedures and welders. 37. Mandatory full radiography in ASME Code Section 8 is required for all welding with thickness exceeding Table UCS-57, and also for lethal service vessels and unfired boilers with Design Pr. More than 50 psig. 38. PWHT is ASME Code Section 8 requirement if thickness exceeds those given in tables UCS-56 (given in notes under the tables). These tables also give min. PWHT temperature and min. holding time (soaking period) based on P-Nos. and thickness respectively. 39. For Furnace PWHT in ASME Code Section 8 , Loading Temperature shall not exceed 800°F, heating rate 400 deg F/hr/inch of thickness, cooling rate 500°F /hr/inch of thickness. Still air cooling permitted below 800°F. During soaking period, temp difference between hottest and coldest part shall not exceed 150°F. 40. Minimum overlap for PWHT in multiple heats = 5 ft. 41. For the ASME Code Section 8 impact test requirement, UCS 66 curve. If MDMT-thickness combination falls on or above the curve, impact testing is exempted. Additional exemptions are given as per UG-20(f) and UCS=68 (c).
