sp3d

SP3D WORK INSTRUCTION Place Design(Logical) Support ________________________________________________________________

0

P.SenthilKumar

MARK

DESCRIPTION

BY

17/12/2010 CHKD

APVD

DATE

REVISION CLIENT

:

Qatar Liquefied Gas Company Ltd.

PROJECT

:

Plateau Maintenance Project – Onshore Facilities

JOB.N°

:

LTC/PMP/215/09

DOC.N°

:

9833N-XXXX-XX-P246-XXX

TCJV.N°

:

9833N-XXXX-XX-P246-XXX

9833N-0000-DOD-P332-001 rev.A1

Date Rev

: :

30/09/2010 0

SP3D WORK INSTRUCTION Place Design(Logical) Support

9833N-0000-PP-P246-001 Page 2 of 12

Revision Table All modifications between the previous and current revision are highlighted by a vertical line in the left margin of the text. Main changes are shown below: N°

Para / Section n°

Explanation / Reason

9833N-0000-DOD-P332-001 rev.A1

Date Rev

: :

30/09/2010 0


9833N-0000-PP-P246-001 Page 3 of 12

CONTENT 1.

INTRODUCTION ................................................................................................. 4

2.

PURPOSE ........................................................................................................... 4

3.

PREPARING TO PLACE DESIGN SUPPORT.................................................... 4

4.

PLACE A DESIGN SUPPORT ............................................................................ 4

5.

PLACING MULTIPLE SUPPORT ........................................................................ 7

6.

SUPPORT MODIFICATIONS............................................................................ 10

9833N-0000-DOD-P332-001 rev.A1

Date Rev

1.

: :

30/09/2010


0

9833N-0000-PP-P246-001 Page 4 of 12

INTRODUCTION This work Instruction explain the procedure to place the design support using the Task module Hangers and supports in software Smart Plant 3D.

2.

PURPOSE In order to issue the Isometrics to Stress group for analysis, it is mandatory to show the support mark on the Pipeline in Isometrics. Hence, Using the Task Hangers and Supports, Piping Designer should place a design support on the Pipeline which will be shown in Isometric when extracted from SP3D.

3.

PREPARING TO PLACE DESIGN SUPPORT This Guide Document assumes that SmartPlant 3D is already installed on your machine and that an administrator has set up a project and libraries for you to use. Before you can place a design support you must first start SmartPlant 3D, open a SmartPlant project and open a piping model within that project.

4.

PLACE A DESIGN SUPPORT When you have loaded the Workspace with required piping model to be placed with Design Support, Switch to Hangers and Support Task from Main menu as shown below.

`

Now the Hangers and Supports Vertical Tool bar has been activated and select Place Support by Point command as shown in figure below.

9833N-0000-DOD-P332-001 rev.A1

Date Rev

: :

30/09/2010 0


9833N-0000-PP-P246-001 Page 5 of 12

TIP: Activate Pinpoint or Point along command to place support at required place on the piperun When the Place support ribbon bar is activated, check the Design box as shown in figure

Select the Pipe feature and accept.

Now the smartstep prompt you to select the Structure to use to support the selected pipe feature Select the structure and Accept. Note: Selecting the Structure is optional in Placing the Design Support.

9833N-0000-DOD-P332-001 rev.A1

Date Rev

: :

30/09/2010 0


9833N-0000-PP-P246-001 Page 6 of 12

Now enter the position of the Support on the pipe run using pinpoint or point along command at specific location precisely.

Finally click on Finish button on ribbon bar to complete the placement of Design Support.

9833N-0000-DOD-P332-001 rev.A1

Date Rev

5.

: :

30/09/2010 0


9833N-0000-PP-P246-001 Page 7 of 12

PLACING MULTIPLE SUPPORT Before start placing the multiple supports, you must enable Point along command from Tools → Point Along. When the command is activated, select the Reference button on Point Along Ribbon Bar and select the Pipe feature along which you intent to place multiple support

Now select Place support by point command from Hangers and supports vertical tool bar. When the Place support ribbon bar is activated, check the Design box as shown in figure

1). Select the Pipe feature to place support and Accept 2). Select the Structure to support the selected Pipe Feature. (Optional) and Accept 3) Now you should select the location of the support. Use the Reference Point Button on Point Along Ribbon bar to select the from Point on the pipe feature as shown in figure below.

9833N-0000-DOD-P332-001 rev.A1

Date Rev

: :

30/09/2010


0

TIP:

9833N-0000-PP-P246-001 Page 8 of 12

Select the any one of the Handles of the Pipe to define the from

Point

After defining the from point, enter the distance on Point along Ribbon bar. Then enter the number of copies of support that you want to place, by using the Copies Combo box on Place support ribbon bar.

9833N-0000-DOD-P332-001 rev.A1

Date Rev

: :

30/09/2010 0


9833N-0000-PP-P246-001 Page 9 of 12

You now should be able to view the supports on the Pipe feature at specified distance as shown in figure above. Click on the workspace to accept the locations and click on Finish button to complete the placement the Supports.

You now have successfully finished placement of multiple supports on Pipe feature at required distance.

9833N-0000-DOD-P332-001 rev.A1

Date Rev

6.

: :

30/09/2010 0


9833N-0000-PP-P246-001 Page 10 of 12

SUPPORT MODIFICATIONS This section explains the procedure to modify the support properties like, Support Tag, Support type, Support Load. To do any modification on Support, Select Support in the Locate Filter Box

Now select the support from the workspace to modify the properties and right click on the support to navigate shortcut menu and select Properties.

On the properties page set the required properties like Load, Material based on design criteria.

9833N-0000-DOD-P332-001 rev.A1

Date Rev

: :

SP3D WORK INSTRUCTION

30/09/2010 0

Place Design(Logical) Support

9833N-0000-PP-P246-001 Page 11 of 12

APPENDIX 1: SHORTCUT KEYS Command or Action

Shortcut Keys

Change active axis of rotation (equipment objects) Note: The default axis of rotation is the Z-axis

Up Arrow key

Component or folder name change

F2

Copy

CTRL+ C

Define Workspace

CTRL+ W

Delete objets

DELETE Key

Edit locate filter

CTRL+ E

End a process

ESC key

Fit all views

Hold SHIFT+ A, and click Fit button

Help

F1

Hyperlink

CTRL+ K

New workspace

CTRL+ N

Open workspace

CTRL+ O

Pan

CTRL+ SHIFT+ P

Paste

CTRL+ V

Pinpoint display on or off

F9

Pinpoint target move

F12

Pinpoint- unlock rectangular or spherical coordinates

F6 (East or absolute distance), F7 (North or horizontal angle), F8 (Elevation or vertical angle)

Previous view

ALT+ F5

Print

CTRL+ P

Recompute objects (compartmentation, molded forms, structural detailing, and structural manufacturing)

CTRL+ R

Refresh workspace

F5

Rotate about the current active axis (equipment objects)

Left and Right Arrow keys

Route in fast mode

SHIFT+ F

Route plane lock by turn or branch

CTRL+ 4

Route plane lock by three points

CTRL+ 5

Route plane lock to El east-west

CTRL+ 2

Route plane lock to El north-south

CTRL+ 3

9833N-0000-DOD-P332-001 rev.A1

Date Rev

: :

30/09/2010


0

9833N-0000-PP-P246-001 Page 12 of 12

Command or Action

Shortcut Keys

Route plane lock to no plane

CTRL+ 6

Route plane lock to plan

CTRL+ 1

Save

CTRL+ S

Select All

CTRL+ A

Selected objects do not move with the pointer during the “Move” command

F10

Shortcut menu for interface component (to open session file in Windows Explorer, dialog box, Workspace Explorer, etc…)

Right- click

SmartSketch locate surface

F3

SmartSketch lock constraint

CTRL+ L or click middle mouse button or wheel

SmartSketch select mode on

CTRL+ D

Start a command or confirm (OK) a dialog box

ENTER key

To Do List

CTRL+ T

Undo

CTRL+ Z

Zoom

CTRL+ SHIFT+ Z

Standard Control Keys

Function Keys

Select All

CTRL+ A

Help

F1

Copy Text

CTRL+ C

Grid Snap

F3

New

CTRL+ N

Exit

ALT+ F4

Open

CTRL+ O

Close File

CTRL+ F4

Print

CTRL+ P

Update Active View

F5

Save

CTRL+ S

Previous Zoom Level

ALT+ F5

Paste Text

CTRL+ V

Paste from Clipboard

CTRL+ F7

Cut Text

CTRL+ X

Toggle PinPoint Display

F9

Redo

CTRL+ Y

Cut to Clipboard

CTRL+ F9

Undo

CTRL+ Z

PinPoint Lock X axis

F10

Select First Menu Item

SHIFT+ F10

PinPoint Lock Y axis

F11

Reset PinPoint Home

F12

9833N-0000-DOD-P332-001 rev.A1

sp3d

Recommend Documents