Sealing Systems for Steam Turbine
Meningkatkan Reliability Steam Turbine melalui Up-grade Sistim Sealing John Crane T28ST + Isomag Bearing Protector
A ISSUE REV.
13.05.2011
First Issue
DATE: DD/MM/YY
STATUS
First Issue DESCRIPTION
This Document is confidential. The copyright is vested in John Crane Indonesia. All rights reserved. Neither the whole nor only part of this document may be disclosed to any third party or reproduced, stored in any retrieval system or transmitted in any form or by any means (electronic, reprographic, recording or otherwise) without the prior written consent of the copyright owner.
TITLE:
Meningkatkan Reliability Steam Turbine DOCUMENT NO.: JCI/11050725
PT. John Crane Indonesia Cilandak Commercial Estate Building # 401A Cilandak, Jakarta 12560 Indonesia ISSUED BY: Rudy Wijaya, John Crane
tel: +62 21 7890068 fax: +62 21 7890848
E-mail:
[email protected]
1
Sealing Systems for Steam Turbine
1. PENDAHULUAN Permasalahan yang sering terjadi pada peralatan Steam Turbine adalah kontaminasi steam dengan minyak pelumas bearing (oil lubricant). Kondisi ini menyebabkan kualitas pelumas tersebut menjadi turun/rusak sama sekali sehingga sistim pelumasan pada bearing tidak terjadi dan bearing menjadi rusak.
CARBON BOXES BEARING SEAL BEARING SEALS OIL
OIL
HIGH PRESSURE STEAM Masuknya steam ke rumah bearing (bearing housing) dimungkinkan karena standard pengesilan pada peralatan Steam Turbine umumnya hanya menggunakan Carbon Bushing yang dipasang/menempel pada casing Steam Turbine dan labyrinth yang dipasang pada bearing housing.
2
Sealing Systems for Steam Turbine
Carbon Bushing di peralatan Steam Tubine lambat laun akan menyebabkan kerusakan pada shaft turbin (scratch) sehingga bocoran steam membesar akibat clearance yang membesar (steam loss). Steam yang bocor tersebut akhirnya masuk ke rumah bearing karena labyrinth yang berfungsi untuk menahan bocoran tersebut juga memiliki keterbatasan pengesilan (adanya clearance pada labyrinth yang standardnya 0.025” s/d 0.035”). Kontaminasi steam (H2O) dengan oli pelumas akan membentuk sludge sehingga sebagaimana yang terjadi pada Carbon bushing, clearance di labyrinth juga lambat laun membesar sehingga volume steam yang masuk ke ruang bearing juga menjadi lebih banyak. Kerusakan standard pada peralatan steam turbine secara berurutan adalah sebagai berikut : 1. Kerusakan shaft akibat gerusan dari carbon bushing (clearance membesar) – volume bocoran steam membesar. 2. Kerusakan labyrinth di bearing housing – terjadi kontaminasi steam dengan pelumas. 3. Point 1 dan 2 menyebabkan kerusakan bearing akibat kualitas pelumas yang menurun. 4. Point 3 menyebabkan kerusakan rotor assy akibat posisi rotor yang turun atau vibrasi yang berlebihan. Kondisi ini akan terus terjadi (repetitive failure) dan menurunkan reliability (kehandalan) steam turbine tersebut karena diperlukan perbaikan (stop unit).
Penggantian Carbon Bushing, labyrinth, bearing yang rusak. Perbaikan shaft yang tergores (scratch) baik pada posisi carbon bushing maupun labyrinth. Perbaikan rumah labyrinth (posisi dimana labyrinth terpasang). Di beberapa kasus bahkan diperlukan penggantian rotor assy (menjadi rusak dan berbiaya lebih mahal) akibat rusaknya bearing.
2. MENINGKATKAN KEHANDALAN STEAM TURBINE Seandainya lebih dicermati maka ujung dari permasalahan (Root Cause) yang diterangkan di atas adalah akibat kurang sempurnanya ‘sistim sealing’ (pengesilan) pada 2 (dua) area pengesilan yaitu di Carbon Bushing dan labyrinth. John Crane sebagai perusahaan pembuat sistim sealing terkemuka di dunia memiliki produk sealing untuk steam turbine yaitu :
Dry Gas Seal (DGS) Type 28 ST, merupakan mechanical seal (non contacting seal) sebagai pengganti carbon bushing assy. Type 28 ST bekerja menggunakan steam proses (dari dalam casing) sebagai sealing media (tidak diperlukan injeksi gas dari luar). Teknologi yang digunakan pada Type 28 ST ini adalah sama dengan teknologi DGS pada centrifugal gas compressor. Dengan memasang DGS Type 28 ST maka volume kebocoran steam menjadi berkurang secara signifikan sehingga tidak lagi terjadi kontaminasi steam dengan pelumas bearing.
Bearing Protector (Isomag), merupakan mechanical seal sebagai pengganti labyrinth yang terpasang pada bearing housing. Bearing protector ini memiliki contact face sehingga mampu
3
Sealing Systems for Steam Turbine mencegah ‘in leakage’ (steam dari luar masuk ke rumah bearing) dan ‘out leakage’ (oli pelumas dari rumah bearing bocor ke atmosphere). Baring protector tidak memiliki clearance seperti labyrinth seal sehingga kemampuan pengesilannya jauh lebih baik. DRY GAS SEAL TYPE 28 ST (STEAM TURBINE)
Type 28ST – Material Construction :
Mating Ring Primary Ring Hardware Secondary Sealing
: Tungsten Carbide : Antimony Filled Carbon : 410 Stainless Steel : Split Carbon Ring(s) and Crane-foil™
Operational Capabilities :
Axial Movement ± 2.5 mm / .1 inches Radial Movement ± .6 mm / .025 inches Inlet Conditions o Pressure 48 bar / 700 psi o Temperature 399°C / 750°F Exhaust Conditions o Pressure 21 bar / 300 psi o Temperature 288°C / 550°F Shaft Speed o Continuous 6000 rpm o Slow Roll 1000 rpm
Worldwide experience :
Over 900 seals currently in operation Worldwide installations in 15 different countries on five continents Over 10 million total operating hours
O.E.M. (Original Equipment Manufacture)
4
Sealing Systems for Steam Turbine
Coppus Tuthill, Dean Hill, Dresser Rand (Terry, Turbodyne, Worthington), Elliot, Hayward Tyler, GE, Westinghouse. BEARING PROTECTOR (ISOMAG)
ISOMAG – Material Construction MAGNUM-S Stationary Face : PTFE Composite Stator : Bronze Rotor : HT 17-4 PH O-rings : Fluoroelastomer MAGNUM-C Stationary Face : HT 17-4 PH Stator : Bronze Rotor : PTFE Composite O-rings : Fluoroelastomer Maximum operating limits
Pressure
: 1.4 barg/20 psig (for MAGNUM-S) 0.3 barg/5 psig (for MAGNUM-C)
Speed
: 60 mps/12,000 fpm Lubricated 20 mps/4000 fpm Dry
Temperature
: Up to 150°C/300°F (for MAGNUM-S) Up to 100°C/225°F (for MAGNUM-C)
Axial Shaft Movement
: ±0.8mm/±0.032"
Allowable TIR
: ±0.5mm/±0.020"
Shaft Diameter
: 19mm to 380mm/0.750" to 15.00"
O.E.M. (Original Equipment Manufacture)
5
Sealing Systems for Steam Turbine
Elliot Model AYR, BYR Elliot Model CYR, DYR, DYRH
3. KEUNGGULAN PRODUK Dry Gas Seal T 28ST untuk Steam Turbine :
Reduce Steam leakage up to 95% Eliminate shaft wear cause by contact of carbon ring Leaks less than carbon rings Less down time due to maintenance Extends operation time No gland condenser required Relatively inexpensive to retrofit Steam Leakage savings : savings can range from $3,000 to $30,000 /year Eliminates down time costs associated with steam leakage (i.e. bearing failures). Carbon rings vs. 28ST, 6-18 months vs. 2-4 yrs Eliminates costs associated with gland condensers. Approximately equivalent in cost to replacement of carbon ring casings
Bearing Protector (ISOMAG) :
Eliminate Vents Seals in Flooded Applications Easy to Install 8 to 10 Years Life Reduces Process Seal Failures Improves Equipment Lifecycle Cost Increased Uptime = Increased Revenue Proven Reliable Technology Seal Harsh Process Environments Provide Liquid Tight Sealing No Shaft Damage Long Life Positive Sealing Eliminate Vents on Pump Power Frames Optimized Designs for Flooded Applications Handles Axial and Angular Shaft Movement Dry Running Capability Protection from External Contaminants Wide Range of Sizes 3/4” to 16”
6
Sealing Systems for Steam Turbine
4. PERBANDINGAN BIAYA – CARBON RING VS TYPE 28 ST
No
Keterangan
Carbon Ring Seal $
1
Cost of Seal (2 units)
2
Leakage Rate/side
200 lbs/hr
0.4 lbs/hr
3
Cost of Steam
$ 0.006/lb
$ 0.006/lb
4
Average Cost of Repair,
4,000
$
4,000
Parts :
$
2,500
$
5,000
$
2,000
0
$
1,500
0
6
Maintenance Cost/year on auxiliary Seal Equipment (Gland Condenser)
8
Operating Hrs/year
9
Operating Cost/year
27,000
$
Preventive Maintenance Cost/year
Expected Seal Life
$
Labor :
5
7
2,000
Type 28 ST Seal
2 years
5 years 7500
7500
a) Labor on repair
$
2,000
$
800
b) Parts on Repair
$
1,250
$
1,000
c) Preventive Maintenance
$
1,500
0
d) Maintenance Auxiliary Equipment
$
1,500
0
e) Steam Losses
$
18,144
$
36
OPERATING COST/YR
$
24,394
$
1,836
COST OF LABOR/YR
$
2,000
$
800
COST OF PART/YR
$
1,250
$
1,000
TOTAL COST
$
29,644
$
30,636
PAYBACK PERIOD (Months) Keterangan : * Cost of Labor/Yr * Cost of Part/Yr
: Cost of labor / Expected seal life : Cost of parts / Expected seal life
* Payback Period
: (Total Cost of T28ST – Total Cost of Seal Ring) / 12
7
12.4
Sealing Systems for Steam Turbine
5. PENUTUP Dengan strategi meng-upgrade sealing system pada Steam Turbine diharapkan mampu meningkatkan kehandalan peralatan yang sekaligus akan meningkatkan keuntungan komersial bagi kilang Pertamina RU-4 Cilacap. Untuk mendapatkan informasi yang lebih detail mengenai mekanisme teknis upgrade sistim sealing ini mohon untuk menghubungi PT. John Crane Indonesia.
+++++++++++++++++++
8