Servoteknikk ServoFighter C4 Fire Alarm Panel Instruction Manual

Inst ruc tio n ma m anual nual

Instruction manual SFC4 E V2 V1.0 - 2004.05.15

Page 1

Page 2

TABLE OF CONTENTS Page OPERATING INSTRUCTIONS ....................................................... ........................................................... ....... 5

FUNCTIONAL DESCRIPTION ...................................................... ........................................................... ................. 5 Normal operation............................................................................................................................................ operation ............................................................................................................................................ 5 Fire alarm ....................................................................................................................................................... 5 Lamp test .......................................................................................................................................................... ........................................................................................................................................................ 5 Fault alarm ..................................................................................................................................................... 5 GENERAL ALARM ........................................................... ........................................................... ........................... 6 DISCONNECTIONS .......................................................... ........................................................... ........................... 6 TECHNICAL SPECIFICATIONS ................................................... ........................................................... ....... 7

MAIN PANEL SERVOFIGHTER C4 ....................................................... ........................................................... ....... 7 Compact panel dimensions ............................................................................................................................. 7 Connection cabinet lay out ............................................................................................................................. ............................................................................................................................. 7 Technical specifications for ServoFighter C4................................................................................................. C4 ................................................................................................. 8 Specifications for inlets and outlets ................................................................................................................ 8 INSTALLATION.................................................. INSTALLATION .................................................. ........................................................... ..................................... 9

PLANNING GUIDELINES .................................................. ........................................................... ........................... 9 R ECOMMENDED ECOMMENDED CABLE TYPES ........................................................... ........................................................... ....... 9 Cable termination ........................................................................................................................................... termination ........................................................................................................................................... 9 MOUNTING THE CABINET ......................................................... ........................................................... ................. 9 TERMINAL CONNECTIONS ........................................................ ........................................................... ............... 10 DETECTORS AND ALARM DEVICES...................................................... ........................................................... ..... 10 COMPACT PANEL SERVOFIGHTER C4 C4........................................................... ........................................................... ...................................................... 12 IT FOR RECESSED MOUNTING – SERVOFIGHTER C4 ...................................................... ................................... 15 K IT K IT IT FOR DISTRIBUTE DISTRIBUTED D MOUNTING – SERVOFIGHTER C4 ........................................................... ......................... 19 OPERATOR PANEL FOR SERVOFIGHTER C4 ........................................................... ............................................. 22 DC/DC CONVERTER FOR 24 VDC SUPPLY ............................................................ ............................................ 26 GENERAL DETECTOR /LOOP CONNECTIONS...................................................... ........................................................... ..... 27 Optical smoke detector, type SSD 521 ...................................................................................................................... 28 Heat detector, type UTD 521.................................................................................................................................. 29 Base for detectors detectors SSD/UTD, type USB 501-1 501-1 ............................................................................................................ 30 Base for SSD/UTD, SSD/UTD, type USB 501-3......................................................................................................................... 31 Remote lamp, type type RAL 720 ................................................................................................................................... 32 .................................................................................................................................. 33 Internal buzzer, type type BA-API .................................................................................................................................. UV flame detector, type UFM-840........................................................................................................................... 34 Heat detector for engine engine room, type STMV-70 STMV-70 and 90 .................................................................................................. 35 Manual callpoint callpoint for accomodation, accomodation, type KR1 ............................................................................................................ 36 Manual callpoint callpoint for engine room, humid humid area, type KSR1 KSR1 ............................................................................................ 37 General alarm callpoint, type WR9304 ..................................................................................................................... 38 .................................................................................................................................. 39 Bilge detector, type SFB-39S SFB-39S .................................................................................................................................. GENERAL CONNECTION – ALARM ORGANS................................................... ...................................................... 40 ALARM BELL FOR ACCOMODATION , TYPE MBF-6WE/24 ....................................................... ............................................ 41 ALARM BELL FOR ENGINE ROOM, TYPE MSB6B24 ..................................................... ...................................................... 42 ALARM LIGH FOR ACCOMODATION, TYPE L101 ......................................................... ...................................................... 43 ALARM SIREN FOR ENGINE ROOM, TYPE SEC-1992/24 .......................................................... ............................................ 44 DOOR HOLDER WITH MAGNET, TYPE GPT-AG .......................................................... ...................................................... 45 COMMISSIONING........................................................ COMMISSIONING ........................................................ ........................................................... ......................... 46

START THE SYSTEM ........................................................ ........................................................... ......................... 46 FUNCTIONAL TEST ......................................................... ........................................................... ......................... 46 YEARLY TESTING AND SERVICING...................................................... ........................................................... ..... 47 MAINTENANCE .................................................... ........................................................... ................................... 47 Page 3

SPARE PARTS ....................................................... ........................................................... ................................... 48 FAULT FINDING .................................................... ........................................................... ................................... 48 R EPLACING EPLACING THE BATTERIES ..................................................... ........................................................... ............... 49 MODIFICATION FOR 24VDC SUPPLY............................................................ ...................................................... 50 PROGRAMMING.......................................................... PROGRAMMING .......................................................... ........................................................... ......................... 50

STANDARD PROGRAMS .................................................. ........................................................... ......................... 50 SELECT NUMBER OF OPERATOR PANELS ....................................................... ...................................................... 50 SELECT BILGE DETECTOR ......................................................... ........................................................... ............... 50

Page 4

OPERATING INSTRUCTIONS Functional description The central unit's primary function is to provide both visual and audible fire alarms. To ensure that the system is always in perfect working condition, the panel monitors continuously all internal circuits and functions, and all cables and equipment mounted externally. The panel gives visual and audible alarm of all operational disturbances.

FIRE

ServoFighter C 4

The fire alarm panel is operated by buttons marked LAMP TEST, PANEL RESET and ALARM SILENCE, and a numeric keyboard (0-9 / C / Enter). The numeric keyboard is used to perform disconnections and changes in the customised programming of the panel.

Normal operation Normal operation is indicated by a green green lamp POWER. No other lamps or outlets are active.

Fire alarm Fire alarm is indicated by two flashing red lamps marked FIRE and a continuously lit red lamp marked ALARMS / ZONE 1-4. The internal buzzer sounds and the alarm bells ring intermittently or continuously (as programmed). The acoustic alarm is stopped by pressing ALARM SILENCE. The area covered by the zone in alarm must be inspected to find out which detector is activated and to determine the cause of the alarm. The panel and detectors are reset by pressing PANEL RESET.

Lamp test When the panel is in normal operation, press the button LAMP TEST. All LEDs on the panel front are lit.

Fault alarm Fault alarm is indicated by one flashing yellow lamp marked FAULT and one or several flashing yellow lamps in the field FAULTS or FAULTS/DISCONNECTIONS. The internal buzzer sounds. The acoustic alarm is stopped by pressing ALARM SILENCE. Faults must be corrected immediately. See section Fault Finding later in the instruction manual. If necessary, contact the local electrician or the manufacturer. When the fault is corrected, the panel is reset by pressing PANEL RESET.

Page 5

Mains fault Mains fault is indicated if the mains supply to the panel is interrupted, or if the mains fuse is broken.

Battery fault Battery fault is indicated if the battery capacity is low, if the battery is almost discharged, if the battery fuse is broken or if the battery connections are interrupted.

Earth fault Earth fault is indicated if the insulation of the external equipment or inside the panel is faulty.

Zone fault Loop fault is indicated if the loop wires are interrupted or broken or if a detector head is removed from a base.

Alarm outlets fault Alarm outlet fault is indicated if the alarm outlet wires are broken or short circuited, or if a fuse is broken. Alarm outlets 1 and 2 are separately monitored.

Control outlet fault Control outlet fault is indicated if the door magnet outlet fuse is broken.

General alarm circuit fault General alarm circuit fault is indicated if the loop wire for the General alarm push button is interrupted or broken.

System fault System fault is indicated if a serious failure occurs in the panel. The panel may be incapable of detecting and indicating a fire alarm. Contact local representative or the manufacturer immediately.

General alarm The panel has a separate input for a General Alarm push button. The alarm bells ring with seven short and one long pulse (or as programmed). No other outlets or LEDs are activated. General alarm function can NOT be disconnected. This inlet also offers the possibility for ‘muting’ the alarm signals (see ‘General detector/loop connections).

Disconnections In some cases it may be necessary to disconnect parts of the system; for example during activity which produces a lot of heat or smoke. It is possible to disconnect parts of the system by using the numeric keyboard. A disconnected function is indicated by a continuously lit lamp markedDISCONNECTIONS and a continuously lamp for the actual function. The following options are available:

Fire zone 1 - 4 Press the key Z1, Z2, Z3 or Z4 Z4 (keys 1,2,3 or 4 on the numeric keyboard) and confirm by pressing ENTER. A disconnected zone will not be activated by a fire alarm, unless the source of the alarm is a manual callpoint. Repeat the operation to reconnect the zone.

Alarm outlet 1 - 2 Press the key AL (key 7 on the numeric keyboard) and confirm by pressing ENTER. The alarm outlets will not be activated by a fire alarm. Repeat Repeat the operation to reconnect the outlets.

Control outlets Press the key CON (key 8 on the n umeric keyboard) and confirm by pressing ENTER. The door hold outlet will not be deactivated by a fire alarm (fire doors remain open). The fault relay will not be activated by a fault alarm. Repeat the operation to reconnect the outlets.

Page 6

TECHNICAL SPECIFICATIONS Main panel ServoFighter C4 Fire alarm panel is delivered as a standard compact panel with operator panel and connection cabinet mounted together. The compact panel is mounted in a painted steel cabinet with a die-cast aluminium front frame, a steel reinforced silk printed front plate which gives textual explanations for all LEDs and keys. The main circuit board inside the panel contains the microcontroller, relays, all fuses for supplies and outlets and the terminals for all external cables. The panel also contains a charging rectifier 230 VAC / 27.0 VDC – 0.8A and built-in batteries 24V – 5Ah. The panel has 4 conventional loops for end-of-line resistors. Each loop can be programmed to operate with standard detectors, Exi detectors/zener barrier or a combination of standard and Exi detectors/zener barrier. The number of detectors on each loop are limited according to the maximum current draw and authority rules. Modifications of the standard panel is possible by assembling a KIT. One KIT for Recessed frame and one for Distributed mounting are available. The panel may be supplied with an additional operator panel or a remote panel, connected to the connection cabinet through a four wire cable. The remote panel is identical to the operator panel, but it can only display the alarms/faults and silence the internal buzzer.

Compact panel dimensions

FIRE 186.0

ServoFighterC rC4

16.0 127.0

300

Connection cabinet lay out A

A

B

A1 A2 D

Mounting hole

Mounting hole

MP / EPROM

PC board

Battery bracket ZONE 1 ZONE 2 ZONE 3 ZONE 4 GEN.

A 1

B 2

A 3

B 4

A 5

B 6

A 7

B 8

A 9

ALA 1

ALA 2

DOOR

FAULT

OPERATOR PANEL

B A B A B A B NC C NO 0V 27V D- D+ Gnd 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

FIRE

NC 25

C 26

MAINS

NO 27

230 VAC 28 29

M

Terminal outlet (1 - 24)

Terminal outlet (25 - 29)

Mounting hole

Mounting hole

A

Fuses : M : Mains

A

A

A = Prepared for PG 13.5 cable glands

B : Battery Battery

A

A

A

A1 / A2 : Alarm Alarm bells 1 /2

Page 7

Technical specifications for ServoFighter C4 MAINS VOLTAGE BATTERY / SUPPLY VOLTAGE PANEL CURRENT CONSUMPTION – NORMAL OPERATION PANEL CURRENT CONSUMPTION - ALARM PANEL CURRENT CONSUMPTION FROM BATTERY DURING MAINS FAILURE MAX. CHARGING CURRENT TO BATTERY FROM CHARGING RECTIFIER BUILT-IN BATTERIES (24V) – recommendations (see spare parts) MAX. NUMBER OF ZONES / LOOPS (Standard – Exi 600 ohm – Standard & Exi 600 ohm) EOL RESISTORS – ZONE / ALARM BELLS / GENERAL ALARM AMBIENT TEMPERATURE RANGE (continuous) PROTECTION CATEGORY TOTAL WEIGHT PANEL ARTICLE NUMBER

230 VAC, +/- 10%, 50Hz 24 VDC 40mA 60mA 1 mA 800mA SHIN-KOBE HV5-12 (2. x 5Ah – 12V) – estimated lifetime 4 years 4 5.6 kohm -20 0 to +60 0 C IP20 8.0 kg 1210050

Specifications for inlets and outlets In-/Outlets

Outlet no.

Voltage

Fuse-

Max. current

Max. units/outl.

OptionActivated by

OptionCancel .by

OptionDisconn. by

Option-Group activation

OptionType of signal

Option - delay by fire alarm

ZONE 1-4 Standard ZONE 1-4 Exi 600 ZONE 1-4 Std & Exi 600 GEN. ALARM ALARM BELLS 1-2 DOOR MAGNETS FAULT ALARM OPERATOR PANEL

1–8 1–8 1–8 9 – 10 11 – 14

24 VDC 24 VDC 24 VDC 24 VDC 24 VDC

32 det. 12 det. 12 det. 1 20 alarm bells 12 magnets

---------

---------

---------

1A

---

Select zones, Two zones simultan., Selected simultan., All zones

Cont., 0.8/0.8 sec., 1.6/1.6 sec., 3.2 / 3.2 sec., 7 short + 1 long

0 sec. 7 min. 30 sec steps of 30 sec.

20 – 24

48 VAC/DC 24 VDC

---

---

2 operator panel

Reset, Silence Reset, Silence Reset, Silence ---

None, Alarm bells, Control outlet,

17 – 19

--------Fire, Fault, Gen. alarm Fire, Fa Fault, Ge Gen. alarm, Reset Fire, Fault, Gen. alarm ---

---------

24 VDC

4.0 mA 1.0 mA 1.0 mA 60 mA 700 mA total 500 mA mA

-------

15 – 16

--------2 x 1 .0 AT 1 x 1 .0 AT NC/NO

---

---

---

---

FIRE ALARM

25 – 27

230 VAC

NC/NO

3A

---

Fire, Fault, Gen. alarm, Reset

Reset, Silence

28 - 29

230 VAC

1 x 1 .0 AT 1 x 2.0 AT

---

---

---

---

---

Cont, 0.8/0.8 sec., 1.6/1.6 sec., 3.2/3.2 sec, 7 short + 1 long ---

0sec. 7 min. 30 sec steps of 30 sec.

230VAC SUPPLY (Note 1) BATTERIES

Select zones, Two zones simultan., Select simultan, All zones ---

---

---

---

---

---

---

---

---

---

24 V

None, Al.bells, Control outlet,

Note 1: As an alternative to the 230 VAC supply, an external 24 VDC VDC supply may be used. A special special 24V/32V isolated DC/DC converter converter is required. Contact Servoteknikk for further details.

Page 8

---

INSTALLATION Planning guidelines The fire alarm panel ServoFighter C 4 contains advanced electronics. To avoid problems and delays, it is of the utmost importance that the system is carefully planned before the installation starts. Check that all drawings and the instruction manual are available at the installation site and that all electricians are familiar with the material supplied.

Recommended cable types Only high-quality cable is recommended for loops and external equipment. Refer to the following table:

Equipment

Type of cable (min. dimensions)

Mains 220 VAC Battery 24 VDC Earth Alarm outlets ** Control outlets Loops Data outlet * Multicore cable ** * Max. voltage drop 3%

MPRX 2 x 1.5 mm2 2 MPRX 2 x 2.5 mm (minimum) PN 1 x 6.0 mm2 2 MPRX 2 x 1.5 mm MPRX 3 x 1.5 mm2 TCX (I) 1 x 2 x 0,75 mm2 (with screen) 2 TCX (I) 2 x 2 x 1.5 mm (with screen) TCX (I) X x 2 x 1.5 mm2 with screen ** Max. voltage drop 4%

Cable termination It is important that all cables are connected correctly to the terminals in the panel, detectors and other equipment connected to the fire alarm system. All cables must be connected to the terminals with end sleeves in order to avoid short circuiting between cable cores.

Mounting the cabinet The compact ServoFighter C4 is delivered for surface mounting :

42.0

216.0 A

A

ø6.0 98.0

116.0

35.0

A

A

A

A

A

A

Page 9

Terminal connections This section describes the terminal inlets/outlets for all cable connections. The terminals are marked with numbers 1 – 29 and with additional functional text. At delivery, 5.6 kohm end-of-line resistors are connected over the zone terminals (1 - 2 / 3 - 4 / 5 - 6 / 7 - 8), general alarm terminals (9 - 10) and alarm outlet terminals (11 - 12 / 13 - 14). Mains (230 VAC) and battery (24 V) must be disconnected during installation!

ZONE 1 A 1

B 2

ZONE 2 A 3

B 4

Z ON E 3 A 5

B 6

ZONE 4 GENERAL ALARM ALARM B EL EL L LS S1 + A B A B 12 7 8 9 10 11

ALARM D OO OO R F AU AU LT LT AL AL AR AR M OPERATOR PANEL B EL EL L LS S 2 MAGNETS (28VDC 1A MAX) + - + - NC C NO 0V 27V D- D+ G nd 13 14 15 16 17 18 19 20 21 22 23 24

FIRE ALARM (230VAC 3A MAX) NC C NO 25 26 27

230VAC SUPPLY 28

M

29

Terminal outlets on main board

1.

A combination of smoke and heat detectors and manual call points can be connected to the conventional zones. Only equipment from Servoteknikk may be used. The terminals are marked ‘ZONE 1-4’. The principle employed is that of end-of-line resistor. Cables A and B exit from the panel, detectors are connected across them, and the zone is terminated by a 5.6 kohm resistor at the last detector. As an option, a bilge detector can be connected to zone 4 (when specially programmed).

2.

Inlet for general alarm push button with one normally open contact. The end of line resistor 5.6 kohm must be connected across this contact. The terminals terminals are marked ‘GENERAL ‘GENERAL ALARM’. ALARM’.

3.

Alarm outlets for 24 VDC fire alarm bells with serial d iode. Move the end-of-line resistor 5.6 kohm to the last alarm bell. The terminals are marked ‘ALARM BELLS 1-2’. Ensure correct polarity of the alarm bells.

4.

Outlet for fire door magnets with normally 24 VDC which is disconnected during fire alarm. The terminals are marked ‘DOOR MAGNETS’.

5.

Outlet for Fault alarm. Potential free change over contact that operates during Fault alarm. The terminals are marked ‘FAULT ALARM (28VDC 1A MAX.)’.

6.

Outlet for the operator panel. The terminals are marked ‘OPERATOR PANEL PANEL – 0V / 27V / D- / D+ / Gnd’.

7.

Outlet for Fire alarm. Potential free change over contact that operates during Fire alarm. The terminals are marked ‘FIRE ALARM (230VAC 3A MAX.)’.

8.

Inlet for mains supply 230 VAC. The terminals are marked ‘230 VAC SUPPLY’.

Detectors and alarm devices SSD 521 UTD 521 USB 501-1 USB 501/3 RAL RAL 720 720 BA-API

Page 10

: Optical smoke detector IP44 : Heat detector IP22 : Base for SSD/UTD IP54 : Base for SSD/UTD IP54 : Rem Remot otee lam lamp p for for SSD/U SD/UT TD : Internal buzzer for SSD/UTD

WR9304 SFB-39S

: General alarm button IP42 : Bilge detector IP65

MBF-6WE24 : Alarm bell IP21

UFM-810/A STMV-70S KR1 KSR1

. UV flame detector * : Heat detector IP66 : Manual call point IP24D : Manual call point IP65

MSB6B24 L101 SEC-1992/24 GPT-AG

: Alarm bell IP54 : Alarm light IP55 : Alarm siren IP43/IP65 : Door magnet 24 VDC-650N

* Requires a separate loop.

Page 11

Compact panel ServoFighter C4

Page 12

Page 13

DIMENSIONS Servoteknikk

FIRE 186.0

ServoFighter C 4

16.0 127.0

300

MOUNTING

42.0

216.0 A

A

= PREPARED FOR 2 x PG13.5 A

ø6.0 98.0

116.0

35.0

A

CONNECTIONS

A

A

A

B B

MP / EPROM

ZONE 1 ZONE 2 ZONE 3 ZONE 4 GEN.

A 1

B A 2 3

B 4

A 5

B 6

A 7

B 8

A 9

ALA 1

ALA 2

DOOR

FAULT

OPERATOR PANEL

FIRE

B A B A B A B NC C NO 0V 27V D- D+ Gnd 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

NC 25

C 26

9 - 10. General alarm 11 - 12. Alarm outlet 1 13 - 14. Alarm outlet 2 15 - 16. Door magnet

SERVOTEKNIKK DRAWN

DATE

HS CHECKED

2004.03.01

230 VAC 28 29

24 VDC 40 mA 60 mA 800mA 2 x 12V - 5Ah

LOOPS - EOL RESISTORS ALARM OUTL. - EOL RESISTORS GEN.ALARM - EOL RESISTOR OPERATING TEMPERATURE PROTECTION CLASS DIN40050 TOTAL WEIGHT ART. NO. - CONTROL PANEL

5k6 5k6 5k6 0 to0 +55 C0 IP22 8.0 kg 1210051

M

M

17 - 19. Fault contact 20 - 24. Operating panel 25 - 27. Fire contact 28 - 29. Mains 230 VAC

IN- / OUTLETS

VOLTAGE

LOOPS 1-4 GENERAL ALARM ALARM BELLS 1-2 DOOR MAGNET FAULT CONTACT OPERATING UNIT FIRE CONTACT MAINS INLET

24VDC 24VDC 24 VDC 24 VDC

FUSES _ _ 1 x 1.0AT 1 x 1.0AT

48 VAC/DC NC/NO _ 24 VDC 230 VAC NC/NO 230 VAC 1 x 1.0AT

MAX. DRAW

100mA 100mA 0.5A 0.5A 1A 100mA 3A 1A

FIRE ALARM PANEL SERVOFIGHTER C4 FOUR COLLECTIVE LOOPS SIZE

A4 DESIGN SCALE

Page 14

OPERATING VOLTAGE OPERATING CURRENT - NORMAL OPERATING CURRENT - ALARM CHARGING CURRENT BUILT-IN BATTERIES

MAINS

NO 27

Terminal in-/outlets (1 - 29)

1 - 2. Loop 1 3 - 4. Loop 2 5 - 6. Loop 3 7 - 8. Loop 4

A

TECHNICAL DATA

M - Mains fuse 1.0 AT B - Battery fuse 2.0 AT A1 - Alarm fuse 1.0 AT A2 - Alarm fuse 1.0 AT D - Door magnet fuse 1.0 AT A1 A2 D

A

FILE :

REV.

1210051E SFC4 E V2 SHEET

1

OF

1

UNLESS OTHERWISE SPECIFIED : DIMENSIONS ARE IN MM

Kit for recessed mounting – ServoFighter C4

Page 15

Page 16

COMPACT PANEL

Art. no. 1273014

Servoteknikk

FIRE

PACKING LIST RECESSED FRAME SF RAL-5004 NUT M4 DIN934 EIZn SCREW PAN HD M4X10 DIN7985 PZD EIZn WASHER M4 DIN 127B EIZn

ALA RMOU TLE T1

A

1 4 4 4

186.0

ALA RMOU TLE T2

CONTROLOUTLETS

GENERALALARMCIRC.

16.0 127.0

300.0

INSTALLATION PROCEDURE During this installation, both mains (230 VAC) and batteries (24 V) must be disconnected from the fire alarm panel. panel. 1. Remove the operator panel bolts (A). Lift the panel carefully of the hinges, and pull it trough the opening in the recessed frame.

2. Remove the knock-out covers (C) Mount the recess frame on the cabinet with four enclosed screws in pre-drilled holes (B vs. C).

RECESSED FRAME

3. Replace the operator panel with bolts (A).

CABINET (without front panel)

B

B C

C

MAIN BOARD

MP / EPROM

220.0 Ø38.0

TRAFO

Ø38.0

C B

C

B

346.0

RECESSED MOUNTING

Recessed frame 324.0

ø6.5

200.0

130.0

186.0

Panel cut out

2.0 16.0 127

304.0 Panel cut out

SERVOTEKNIKK DRAWN

FIRE ALARM PANEL SERVOFIGHTER C4

DATE

JAS CHECKED

KIT FOR RECESSED MOUNTING SFC4

2004.03.02 SIZE

A4 DESIGN SCALE

FILE :

REV.

1273014E SFC4 V2 Recessed frame SHEET

1

OF

1


Page 17

Page 18

Kit for distributed mounting – ServoFighter C4

Page 19

Page 20

Art. no. 1273021 1273021

COMPACT PANEL

PACKING LIST REAR COVER SF YELLOW CHROME

1

BLIND COVER SF, BLUE RAL-5004 SCREW PAN HD DIN7985 M3X6 PZD EIZn

1 4

SERRATED WASHER M3 DIN6798A EIZn CABLE FERRULE 0.75/14 WHITE CABLE TIE 2,5X98MM BLACK

4 8 2

Servoteknikk

FIRE A

ALA RMOU TLE T1

MAINS

ALA RMOU TLE T2

BATTERY

CONTROLOUTLETS

EARTH

GENERALALARMCIRC.

SYSTEM

Cable glands (PG13.5) and four wire cable with shield are NOT supplied. Recommended cable : TCX(I) 2x2x0.75mm 2

186.0

16.0 127.0

300.0

INSTALLATION PROCEDURE During this installation, both mains (230 VAC) and batteries (24 V) must be disconnected. 1. Remove the operator panel bolts (A). Lift the panel carefully and remove the four wire cable and the earth wire from the operator panel terminals.

3. Mount a cable gland (PG13.5) in the rear cover and secure it with a nut. Insert the new four wire cable with shield and terminate the shield in the cable gland.

6. Mount a cable gland (PG13.5) in the cabinet and secure it with a nut. Insert the new four wire cable with shield and terminate the shield in the cable gland.

2. Disconnect the four wire cable (in the 4. Remove the cable insulation and mount 7. Remove the cable insulation and mount end sleeves on all four wire ends. end sleeves on all four wire ends. cable tree) from the main board. Connect the four wire cable to the terminals Connect the four wire cable to the terminals Cut the cable ties and remove the on the operator board (27V/0V/D+/D-). on the main board (27V/0V/D+/D-). four wire cable. Cut the earth wire close to the blue connector (short wire remains). 5. Mount the rear cover on the operator panel with 8. Mount the blind cover on the cabinet with Replace the cable ties with new ones. the four enclosed screws and serrated washers (B) the original bolts (A) for the operator panel.

OPERATOR PANEL (rear view)

CABINET (without front panel)

250

38

Recessed

B

B

Rear side

MAIN BOARD

Side

MP / EPROM

Cover

164

PG13.5

Recessed

Ø38.0

B

TRAFO

Ø38.0

B 4 wire cable w. shield

4 wire cable w. shield

4 wire cable w. shield

PG13.5

DISTRIBUTED MOUNTING 272.0 300.0 (110.0 deep)

250.0 Panel cut out

ø6.5

CONNECTION CABINET (surface mounting)

164.0 Panelcut out

186.0 A

max. 100m

SERVOTEKNIKK DRAWN

CHECKED

KIT FOR DISTRIBUTED MOUNTING FIRE ALARM PANEL SERVOFIGHTER C4

DATE

JAS

BLIND COVER

2004.03.03 SIZE

A4 DESIGN SCALE

FILE :

REV.

1273021E SFC4 Kit for distr mount. SHEET

1

OF

1


Page 21

Operator panel for ServoFighter C4

Page 22

Page 23

DIMENSIONS FOR OPERATOR PANEL 250

38

Recessed

A

A

Rear side

300 Front

Side

Servoteknikk POWER

FIRE

FAULT

DISCONNECTIONS

Rear cover ALARMS

164

PG13.5

Recessed

FAULTS

ZONE1

ZONE1

ALAR MOUT LET1

MAINS

ZONE2

ZONE2

ALAR MOUT LET2

BATTERY

ZONE3

ZONE3

CONTROLOUTLET

EARTH

ZONE4

ZONE4

GENERALALARM CIRC.

SYSTEM

LAMP TEST

A

FAULTS/DISCONNECTIONS

PANEL RESET

7

8

9

4

5

6

1

2

3

C

0

ENTER

186

ALARM SILENCE

A

272 4 wire cable w. screen to panel

4 wire cable w. screen to panel

CONNECTION UNIT (without operator panel)

INSTALLATION PROCEDURE During installation, mains (230VAC) and batteries (24V) must be disconnected.

4 wire cable w. screen to standard operator panel

Cable glands, four-wire cable and end sleeves are supplied by the installer. Main board

Recommended cable : TCX(I) 2x2x0.75mm 2x2x0.75mm

2

The operator panel can be mounted : Recessed (see dimensions on drawing) Surface in cabinet (additional equipment)

MP / EPROM

B

B

1. Remove the screws and serrated washers (A) from the rear side of the operator panel and remove the rear cover.

Ø38.0 Ø38.0

TRAFO

2. Mount the cable gland PG13.5 in the rear cover. 3. Pull the four-wire cable with screen through the cable gland in the rear cover and terminate the screen in the cable gland.

4 wire cable w. screen for the additional operator panel

4. Dismantle the four-wire cable and mount the end sleeves on the four wires. (27V/red, 0V/blue, D+/green, D-/yellow).

PG13.5

5. Connect the four-wire cable to the terminals on the P.C.board in the operator panel (27V/red, 0V/blue, D+/green, D-/yellow).

TECHNICAL DATA 6. Mount the rear cover on the operator panel with the four screws and serrated washers again (A)

OPERATING VOLTAGE

24 VDC

CURRENT CONSUMPTION-NORMAL CURRENT CONSUMPTION-ALARM NO. OF ADD. OPERATOR PANEL AMBIENT TEMPERATURE RANGE DEGREE OF PROTECTION WEIGHT ART. NO.

10 mA 15 mA 1 0 - +55 C 0 IP22 1.6 kg 1210077

7. Remove the operator panel / front on the main panel by removing the two bolts (B) and unhook the door from the hinges. 8. Mount the cable gland PG13.5 in one of the cabinet's knock-out covers. 9. Pull the four-wire cable with screen through the cable gland in the cabinet and connect the screen in the cable gland.

Max. resistance in the four-wire cable is 10 ohm in each wire.

10. Dismantle the four-wire cable and mount the end sleeves on the four wires. (27V/red, 0V/blue, D+/green, D-/yellow).

Max. length with the recommended cable TFX(I) 2x2x0.75 is as follows :

11. Connect the four-wire cable to the terminal in the main panel, in parallel with the original front (27V/red, 0V/blue, D+/green, D-/yellow).

2

L (meter) = R (ohm) x Q (mm ) x 57 = 10 x 0.75 x 57 = 427.5m

12. Mount the original front on the main panel by placing it on the cabinet and mounting the two bolts (B).

SERVOTEKNIKK DRAWN

HS CHECKED

REMOTE PANEL SFC4 E

DATE

2004.03.02 SIZE

A4 DESIGN SCALE

Page 24

FILE :

REV.

1210077E SFC4 V2 Remote panel SHEET

1

OF

1


Page 25

DC/DC converter for 24 VDC supply

DIMENSIONS / MOUNTING 137.5 83.0

24V DC INLET

+ - - +

n I O u t

DC/DC CONVERTER Type DCC-2432 In : 24VDC

Art.no. 12189

Out : 32VDC

110.0

Max 3A

119.0

SERVOTEKNIKK

32V DC OUTLET

ø5.0

CONNECTIONS Inlet 24VDC external supply

-

+

+

-

+ - - +

n I O u t

DC/DC CONVERTER Type DCC-2432 In : 24VDC

Art.no. 12189

Out : 32VDC

Max 3A

SERVOTEKNIKK

+

Outlet 32VDC supply for the fire alarm panel

SPECIFICATIONS INLET VOLTAGE

22 - 30V DC

* Protected against reversed polarity and overvoltage (transorb diode against transients). Switches off automatically at input voltage over and under the specified range. Fuse at input.

OUTLET VOLTAGE MAX. CURRENT DRAW FROM OUTLET (continuous) MAX. CURRENT DRAW FROM OUTLET (intermittent)

32V DC 2A 3A

* Thermal protected, short circuit proof and overvoltage protection (output)

CURRENT DRAW - NO LOAD RIPPLE

90mA 10mV RMS

* Input and output are electrically separated from chassis. The input is electrically separated from output.

AMBIENT TEMPERATURE RANGE PROTECTION CATEGORY ACC. DIN40050 EMC STANDARD - EMISSION

-20 to +30 0 C IP20 EN 50081-1

* Complies with the relevant EU directives.

EMC STANDARD - IMMUNITY WEIGHT

EN 50082-1 0.6 kg

* CE - marked.

ART. NO.

1273030

* 6.3mm push-on terminals (input and output)

SERVOTEKNIKK DRAWN

TYPE DCC-2432

DATE

ST CHECKED

24V DC/DC CONVERTER FROM 24VDC TO 32VDC

2002.04.22 SIZE

A4 DESIGN SCALE

Page 26

FILE :

REV.

12273030E SHEET

1

OF

1


Optical smoke detector, type SSD 521

DIMENSIONS

DESCRIPTION

TOP VIEW

SIDE VIEW

The SSD 531 detects at an early stage smouldering fires and open fires with smoke developement. Light transmitter and light receiver are arranged in the sampling chamber so that the light beam from the transmitter cannot strike the receiver directly. Only the light scattered by suspended particles reaches the receiver and is converted into an electrical signal. The most important features are : * Digital signal processing * Self-check with active fault display condition (LED flashes 1 Hz) * Alarm filter with dynamic limitations for reducing false alarms. * Alarm threshold follow-up with endof range message (LED flashes 1 Hz)

67.5

The detection loop operates with current amplification, 2 cond. technology and an end-of-line resistor

REAR VIEW

1 - GND line (in and out) 2 - Plus line (in or out) (data) 3 - Plus line (in or out) (data) 4 - GND alarm output 5 - Plus alarm output (max. 6mA) 6 - Cross-connection point (screening)

CONNECTIONS

1 2

LOOP IN

3

Sc A

B

4 5

BASE USB 501-1

1 2 SSD 521

3 4 5

NOTE ! Shield is not required

118.0

6 + Sc A

B

LOOP OUT

-

Remote lamp

The end-of-line resistor must be mounted on the last detector or the end of the loop.

TECHNICAL DATA PRINCIPLE OF OPERATION AREA TO BE MONITORED MOUNTING HEIGHT PERMISSABLE AIR SPEED

max. 20 m/s

SENSITIVITY OPERATING VOLTAGE

acc. to EN 54 - 7 18 - 30 VDC

CURRENT CONSUMPTION AT 30 VDC - NORMAL CURRENT CONSUMPTION AT 30 VDC - ALARM

max. 120 uA min. 19 mA / max. 22.5 mA

SIGNAL TRANSMISSION REMOTE LAMP PROTECTION CATEGORY in combination with base USB 501-1)

Current amplification, 2-conductor technology Up to 28 vdc, max. 5 mA (short circuit proof) IP44

TESTING BY VdS AMBIENT TEMP. RANGE (continuous)

acc. EN 54, parts 7 -20 to +60 O C

AMBIENT HUMIDITY (briefly without condensation) at 40 0 C AMBIENT HUMIDITY (continuous without condensation) at 40 0 C

95 % rel. h. 70 % rel. h.

DIMENSIONS WITH BASE USB 501-1 HOUSING MATERIAL / COLOUR WEIGHT ART. NO.

Ø 118.0 mm / 78.0 mm ABS / PC - ELECTRIC WHITE 105 g

SERVOTEKNIKK DRAWN

SCATTERED LIGHT (Tyndall effect) max. 74 m 2 max. 16 m

CONVENTIONAL SCATTERED LIGHT SMOKE DETECTOR

DATE

ST CHECKED

TYPE SSD 521

2002.04.22 SIZE

A4 DESIGN SCALE

Page 28

1270203

REV.

FILE :

1270203E SSD 521 SHEET

1

OF

1


Heat detector, type UTD 521

DESCRIPTION

DIMENSIONS TOP VIEW

SIDE VIEW

The UTD 521 detects open fires with or without smoke developement. It measures the ambient temperature and responds if the values specified according to EN for the rate of rise of temperature or the maximum temperature is exceeded. The universal temperature detector UTD 521 is available in three sensitivity ranges according to EN 54. The most important features are : * Digital signal processing * Self-check with active fault display in the fault condition (LED flashes 0.2 Hz) The detection loop operates with current amplifications, 2 conductor technology and an end-of-line resistor.

67.5

CONNECTIONS

REAR VIEW

1

LOOP IN

2

Sc A

1 - GND line (in and out) 2 - Plus line (in or out) (data) 3 - Plus line (in or out) (data) 4 - GND alarm output 5 - Plus alarm output (max. 6mA) 6 - Cross-connection point (shielding)

B

3 4

BASE USB 501-1

5

1 2 3

NOTE ! Shield is not required.

UTD 521

4 5 6

118.0 + Sc A

B

LOOP OUT

-

Remote lamp


TECHNICAL DATA PRINCIPLE OF OPERATION AREA TO BE MONITORED

NTC TEMPERATURE SENSOR max. 37 m 2

MOUNTING HEIGHT SENSITIVITY UTD 521

max. 7.5 m acc. to EN 54, part 5, Class 1

SENSITIVITY UTD 521-2 SENSITVITY UTD 521-3

acc. to EN 54, part 5, Class 2 acc. to EN 54, part 5, Class 3

OPERATING VOLTAGE CURRENT CONSUMPTION AT 30 VDC - NORMAL

18 - 30 VDC max. 150 uA

CURRENT CONSUMPTION AT 30 VDC - ALARM SIGNAL TRANSMISSION REMOTE LAMP

min. 19 mA / max. 22.5 mA Current amplification, 2-conductor technology Up to 28 VDC / max. 5 mA (short circuit proof)

PROTECTION CATEGORY in combination with base USB 501-1 TESTING BY VdS

IP22 acc. EN 54, parts 5/6

AMBIENT TEMP. RANGE (continuous) AMBIENT HUMIDITY (briefly without condensation) at 40 0 C AMBIENT HUMIDITY (continuous without condensation) at 40 0 C DIMENSIONS WITH BASE USB 501-1

-20 to +70 O C 95 % rel. h. 70 % rel. h. Ø 118.0 mm / 78.0 mm

HOUSING MATERIAL / COLOUR WEIGHT ART. NO. for UTD 521 / UTD 521-2 / UTD 521-3

ABS / PC - ELECTRIC WHITE 105 g

SERVOTEKNIKK DRAWN

CONVENTIONAL UNIVERSAL TEMPERATURE DETECTOR

DATE

ST CHECKED

1270224 / 1270225 / 1270226

TYPE UTD 521, UTD 521-2 and UTD 521-3

2002.04.22 SIZE

A4 DESIGN SCALE

REV.

FILE :

1270224E UTD 521 SHEET

1

OF

1


Page 29

Base for detectors SSD/UTD, type USB 501-1

DIMENSIONS

A B

B

D

6 5

C

B 104.0

max. 84.0

min. 44.0

4

B

E

118.0

3

B B

B

2 1

r

ot c te e d th

B

B A

i

w t

h gi e H

9.0

ø4.5/23.0

25.0 28.0 78.0

MOUNTING / METHODE OF CABLE ENTRY

A - Fixing B - Cable entry C + D - Entry at inner circumferance E - Fixing for additional terminals

CONNECTIONS

Flush mounted installation through dropped ceiling

LOOP IN Sc A


B

Hole B BASE USB 501-1 Surface mounted installation

1 2 3

NOTE ! Shield is not required (conv. loops)

Ceiling

Detector

4 5 6

Entry C or D

+ Sc A

Hole B

B

LOOP OUT

-

Remote lamp

The end-of-line resistor must be moved to the last detector or t he end of the loop.

TECHNICAL DATA MOUNTING METHODES APPLICATION

SURFACE MOUNTING DRY AND HUMID ROOMS

PROTECTION CATEGORY TESTING BY VdS AMBIENT TEMP. RANGE (continuous)

IP44 acc. EN 54, part 5 / 6 / 7 -20 to +70 O C

AMBIENT HUMIDITY (briefly without condebsation) at 40 C AMBIENT HUMIDITY (continuous without condensation) at 40 C

90 % rel. h. 70 % rel. h.

TERMINALS HOUSING MATERIAL / COLOUR WEIGHT ART. NO.

SCREW TERMINALS, 2.5 mm ABS / PC, FR90 / ELECTRIC WHITE approx. 83 g

SERVOTEKNIKK DRAWN

UNIVERSAL BASE FOR SURFACE MOUNTING

DATE

ST CHECKED

TYPE USB 501-1

2002.04.22 SIZE

A4 DESIGN SCALE

Page 30

1270404

REV.

FILE :

1270404E USB 501-1 SHEET

1

OF

1


Base for SSD/UTD, type USB 501-3

DIMENSIONS

E

E

D For PG13.5

A

B C B

123.0

r

w

ot c et e d th

B

B

E

6

B

B

B

i

3

2

B

A

86.0

4

B

E

E

5

1

t

h ig e h l at o T

D

E

A - Fastening of base insert B - Passage in bottom C - Fastening for additional terminals D - Fastening points for USB 501-3 E - Cable entry stoppers (screw unions)

E

53.0 105.0

MOUNTING

CONNECTIONS

LOOP IN Sc A

B


Plugs

BASE USB 501-3 Detector base USB 501-1

1 2 3 4

NOTE ! Shield is not required (conv. loops)

Detektor

5 6

Detector series 521 or 531 Insert sealing ring together with detector into base

+ Sc A

B

LOOP OUT

-

Remote lamp

The end-of-line resistor must be moved to the last detector or the end of the loop.

TEKNISKE DATA MOUNTING METHODES

Surface mounting for humid areas

APPLICATION PROTECTION CATEGORY TESTING BY VdS

Humid areas acc. to technical technical data IP54 acc. EN 54, part 5 / 6 / 7

AMBIENT TEMP. RANGE (continuous) AMBIENT HUMIDITY (briefly without condebsation) at 40 0 C

-20 to +70 0 C 95 % rel. h. 70 % rel. h. Cable screw terminals, 2.5 mm

AMBIENT HUMIDITY (continuous without condensation) at 40 0 C TERMINALS HOUSING MATERIAL / COLOUR WEIGHT ART. NO.

ABS / PC, FR90 / ELECTRIC WHITE ca. 200 g 1270406

SERVOTEKNIKK DRAWN

BASE FOR HUMID AREAS

DATE

ST CHECKED

TYPE USB 501-3

2002.04.22 SIZE

A4 DESIGN SCALE

REV.

FILE :

1270406E USB 501-3 SHEET

1

OF

1


Page 31

Remote lamp, type RAL 720

DIMENSIONS

85.0

OPEN

OPEN

85.0

The remote lamp is opened by bending a plastic clip and then lifting the front.

30.0

CONNECTIONS

MOUNTING

4 60.0

5

SSD 521/531 UTD 521/531

- + + + - + + +

D4 D1-3

SPECIFICATIONS TECHNICAL DATA

RAL 720

MATERIAL CABINET

PLASTIC PC, WHITE

MATERIAL LENS OPERATING VOLTAGE

PLASTIC TRANSPARENT, RED 6 to 30 VDC

CURRENT CONSUMPTION AT U B MOUNTING

max. 2.7 mA EASILY VISIBLE

AMBIENT TEMPERATURE PROTECTION CATEGORY ACC. TO DIN40050 WEIGHT

-20 to +60 0 C IP42 53 g

ART. NO.

1270482

SERVOTEKNIKK DRAWN

DATE

ST CHECKED

REMOTE LAMP RAL 720 for detectors SSD 521/531 and UTD 521/531

2 0 0 2 . 0 4 .2 2 SIZE

A4 DESIGN SCALE

Page 32

FILE :

REV.

1270482E RAL 720 SHEET

1

OF

1


Internal buzzer, type BA-API

DIMENSIONS

K F D Mounting holes 58.00

Mounting holes

37.00

4

12.50

+ 5

Base USB 501-x

MOUNTING

CONNECTIONS

P.C.board BA-API

LOOP IN A

Sc A B

B

6

1 - GND line (in and out) 2 - Plus line (in or out) (data) 3 - Plus line (in or out) (data) 4 - GND alarm output 5 - Plus alarm output (max. 6mA) 6 - Cross-connection point (screening) NOTE ! Shield is not required for conventional loops

5

B

Mounting clips

4

BASE USB 501-x

3

B B

1 2

2 1

BA-API

3 4 5

B Black

A

Red

Detektor

6

Sc A

B

LOOP OUT The P.C.board is placed in the base as shown above and mounted by pushing it on the mounting clips. The red wire (+) is connected to terminal 5 and the black wire (-) is connected to terminal 4.


When the internal buzzer BA-API is connected, it is NOT possible to connect a remote lamp.

TECHNICAL DATA MOUNTING METHODE SOUND SOURCE

INTERNAL IN BASE TYPE USB 501-x PIEZO BUZZER

PROTECTION CATEGORY OPERATING VOLTAGE CURRENT CONSUMPTION

IP44 +6 til +10V DC 5 mA (from detector)

SIGNAL FREQUENCY SOUND LEVEL

3 kHz intermittent at 4 Hz ca. 70 dB (at 1m distance)

AMBIENT TEMPERATURE RANGE

-0 to +60 O C

POLARITY PROTECTION WEIGHT ART. NO.

DIODE ca. 83 g 1270477

SERVOTEKNIKK DRAWN

INTERNAL BUZZER TYPE BA-API FOR BASE TYPE USB 501-x

DATE

ST CHECKED

2002.04.22 SIZE

A4 DESIGN SCALE

REV.

FILE :

1270477E SHEET

1

OF

1


Page 33

UV flame detector, type UFM-840

DIMENSIONS

MOUNTING 106.0

75.0

122.0

C

PG16

PG16

PG16

4

3

142.0

5

L E D

143VT 6 2

PG16

UFM-840 w.base 143VT

ø7.0

1

PG16

PG16

C

73.0 C

32.5

4

3

114.0

5

L E D

143UH

92.0

100.0

6

2

1

UFM-840 w.base 143UH

C

73.0

C

4

5

Ø3.8 3

L E D

143A

80.0

60.0

6

2

UFM-840 w.base 143A

C-Cable entry

SPECIFICATIONS

OPERATING VOLTAGE

20 - 30 VDC

CURRENT - NORMAL OPERATION.

0.8 mA

143A

Flame ø50cm/15m

RECEIVER RANGE

max. 20m

MAX. NUMBER / LOOP

1

PARALLEL INDICATOR VdS APPROVAL ENVIRONMENT TEMP.

-20 to +600 C

A

1

B

2

End-of-line resistor must be mounted in the last detector or at the end of the loop.

3

Sc

max. 150 mA

4

B

G28 808

5

A

Remote lamp

PROTECTION

IP42

IP42

IP54

IP42

WEIGHT

108g

50g

340g

130g

ART. NO.

1270233

1270401

1270402

1270403

LOOP

6

DIGITAL UV FLAME DETECTOR UFM 840

DATE

with bases 143A, 143VT and 143UH

2002.05.16 SIZE

A4 DESIGN SCALE

Page 34


143UH

LOOP

25 mA

SENSITIVITY

SERVOTEKNIKK

CHECKED

143VT

Sc

CURRENT - ALARM

ST

C

CONNECTIONS UFM 840

DRAWN

1

FILE :

REV.

1270233E UFM 840 SHEET

1

OF

1


Heat detector for engine room, type STMV-70 and 90

DIMENSIONS w. base 77.0 P

A L M E R H T

68.0 P

DETECTOR

S T M V - 7 70 P

P

77.0

P

P 0

7 0

P

P

P - Holes for PG16

MOUNTING

P

CONNECTIONS

P ø4.5

The end-of-line resistor must be mounted on the last detector or the end of the loop

STMV-70/90

62.0

P

Sc

P

LOOP

Sc

A

A

A

B

B

B

L+ L-

P

LOOP Remote lamp

P

The joint for the shield must be isolated inside the base. NOTE ! Shield is not required

62.0 P - Holes for PG16


STMV-70

STMV-90

OPERATING VOLTAGE

24 VDC

24 VDC

CURRENT DRAW CONV. LOOP - NORMAL OPERATION

0.05 mA

0.05 mA

CURRENT DRAW CONV. LOOP - ALARM OPERATION

62.2 mA

62.2 mA

ALARM TEMPERATURE TEMPERATURE

70

90

REMOTE LAMP

CHECKED

0

C

6V, max. 50 mA

6V, max. 50 mA -20 to +70 0 C

ENVIRONMENT TEMP.

-20 to +70 0 C IP66

IP66

IP66

WEIGHT

63 g

63 g

123 g

ART. NO.

1270221

1270222

1270407

DIGITAL HEAT DETECTORS STMV-70 / STMV-90 for engine room and humid hu mid areas with base 185A0175

DATE

ST

C

PROTECTION

SERVOTEKNIKK DRAWN

0

185A0175

2002.04.20 SIZE

A4 DESIGN SCALE

FILE :

REV.

1270221E STMV70 SHEET

1

OF

1


Page 35

Manual callpoint for accomodation, type KR1

DIMENSIONS/MOUNTING

CONNECTIONS

10.5

BRANN FIRE KNUS GLASSET

87.0 BREAK GLASS

KR1

KR1 Blue

19.5

87.0 79.0

Red

19.5 B

40.0 *

A

87.0 89.0

ETT/1-P NOTE ! Shield is not required

27.0

ETT/1-P

A

LOOP

11.0

54.0 *

A

B

B

Sc

Sc

LOOP

60.0 * Cut out for desk mounting 54.0 (w) / 40.0 (h)

87.0 89.0 50.0

87.0

KR1 Red

Blue

SR3T-P 60.0

32.0

87.0

SPECIFICATIONS

SR3T-P

TECHNICAL DATA

KR1

OPERATING VOLTAGE CURRENT - NORMAL

24 VDC 0.0 mA 118.0 mA

CURRENT - ALARM ENVIRONMENT TEMP. PROTECTION WEIGHT ART. NO.

ETT/1-P

ST/TS CHECKED

50g

1270240

1270421

50g 1270420

A

A

B

B

Sc

Sc

LOOP


CONV. MANUAL CALLPOINT KR1 for surface and flush mounting

DATE

2002.04.20 SIZE

A4 DESIGN SCALE

Page 36


LOOP

-30 to +70°C IP24D 2 00 g

SERVOTEKNIKK DRAWN

SR3T-P

FILE :

REV.

1270240E KR1 SHEET

1

OF

1


Manual callpoint for engine room, humid area, type KSR1

DIMENSIONS

BRANN FIRE KNUS GLASSET

170.0 BREAK GLASS

123.0

60.0

74.0

MOUNTING

CONNECTIONS

ø5.0

LOOP

Sc A B The joint for the shield must be isolated inside the unit

74.0

1 2 3

SPECIFICATIONS Shield is not required

TECHNICAL DA DATA

KSR1

OPERATING VOLTAGE CURRENT - NORMAL CURRENT - ALARM

24VDC 0.0 mA 118.0 mA

ENVIRONMENT TEMP. PROTECTION WEIGHT

-30 to +70°C IP65 430 g 1270241

ART. NO.

SERVOTEKNIKK DRAWN

LOOP

B


CONV. MANUAL CALLPOINT KSR1 for engine room/humid areas

DATE

ST/TS CHECKED

Sc A

2002.04.20 SIZE

A4 DESIGN SCALE

REV.

FILE :

11270241E KSR1 SHEET

1

OF

1


Page 37

General alarm callpoint, type WR9304

DIMENSIONS/MOUNTING

CONNECTIONS

GENERAL ALARM ø4.0

87.0 0

104.0

1

WR9304 w. cover PS078W


Blue

60.0

Red

END-OF-LINE RESISTOR

42.0

87.0

TERMINAL BLOCK (supplied by installer)

92.0


GENERAL ALARM

50.0

87.0

SR3T-P 60.0

32.0


87.0 Blue

Red

END-OF-LINE RESISTOR

TECHNICAL DATA

WR9304

OPERATING VOLTAGE CURRENT - NORMAL CURRENT - ALARM ENVIRONMENT TEMP.

24 VDC 0.0 mA 118.0 mA

PROTECTION

IP24D 200g

10g

1270416

1270422

WEIGHT ART. NO.

PS078W

SR3T-P

SR3T-P NOTE ! Shield i s not required

-30 to +70°C

GENERAL ALARM

50g 1270420

The end-of-line resistor must be mounted according to drawing.

SERVOTEKNIKK DRAWN

for surface and flush mounting

DATE

ST CHECKED

GENERAL ALARM PUSH BUTTON WR9304

2002.04.20 SIZE

A4 DESIGN SCALE

Page 38

FILE :

REV.

1270416E WR9304 SHEET

1

OF

1


Bilge detector, type SFB-39S

DIMENSIONS / MOUNTING 58.0

75.0

5 4 1

0.

PUSH FOR TEST

ø5.0

Connection cable

Connection cable

CONNECTIONS

Connection box (not included)

Sc

Earth

A

EOL

ZONE 4 (main panel)

B Unpolarized SFB-39S



24VDC 0.0 mA

CURRENT - ALARM ENVIRONMENT TEMP. PROTECTION

4.1 mA +5 to +50 0 C IP65

WEIGHT ART.NO.

180 g 1270245

SERVOTEKNIKK DRAWN

CHECKED

BILGE DETECTOR SFB-39S

DATE

ST

SFB-39S

OPERATING VOLTAGE CURRENT - NORMAL

2002.04.20 SIZE

A4 DESIGN SCALE

FILE :

REV.

1270245E SFB-39S SHEET

1

OF

1


Page 39

General connection – alarm organs ALARM OUTLET IN PANEL

+

-

-

+

MBF-6WE24

+ -

MBF-6WE24

+

+

-

-

Black Red

MSB6B24

Red Blue

MSB6B24

+ -

KB-46

+ -

L101

2nd 2nd

SEC1992

1st Com

+

Com

+

+

-

-

SEC1992

-

1st

+

+

+

-

-

L101 + -

+

+

-

-

LUFT

LUFT

2

1/4-1/8 TYPE 12

LED

(KT75-400) 1

1/4-1/8 TYPE 12 (KT75-400)

2 1 EOL

+

+

-

-

The end-of-line resistor must be mounted in the last alarm organ or at the end of the loop.

SERVOTEKNIKK DRAWN

ALARM CONNECTION CONNECTION SYSTEM SYSTEM for alarm bells, lights and sirens

DATE

ST CHECKED

2002.03.02 SIZE

A4 DESIGN SCALE

Page 40

FILE :

REV.

ALACONN-A SHEET

1

OF

1


Alarm bell for accomodation, type MBF-6WE/24

DIMENSIONS 150.0

58.0

Material : Varnished steel, grey

MOUNTING

CONNECTIONS 85.7

(Installation box)

-

+

85.7 Alarm outlet from panel

+ -

+ -

Next alarm bell or end-of-line resistor

+ -


Ø4/5

Field wiring max. 2.5mm2

Ø6/9

Remove the gong

60.0

SPECIFICATIONS

Alarm outlet from panel

TECHNICAL DATA

MBF-6WE/24

OPERATING VOLTAGE CURRENT

24 VDC +/- 20% 30 mA

ENVIRONMENT TEMP SOUND OUTPUT

-30 to +75 0 C 95 dB(A)

PROTECTION WEIGHT

IP 21 850 g

+ -

-

ART. NO. 1270601 VERTICAL MOUNTING ONLY

(Wall mounting)

SERVOTEKNIKK DRAWN

CHECKED

ALARM BELL MBF-6WE/24

DATE

ST

+

for accommodation

2002.04.20 SIZE

A4 DESIGN SCALE

REV.

FILE :

1270601E MBF-6WE24 SHEET

1

OF

1


Page 41

Alarm bell for engine room, type MSB6B24


67.0

120.0

KB-46 86.0 ø7.0

WB4 133.0

ø3.5

60.0 M4.0

PG13.5

122.0 127.0 146.0

40.0 15.0

SPECIFICATIONS

CONNECTIONS


Red

+ -

Black

+ -


TECHNICAL DATA

MSB6B24

OPERATING VOLTAGE CURRENT SOUND LEVEL

24 VDC 30 mA 94 dB(A)

ENVIRONMENT TEMP PROTECTION WEIGHT

-35 to +66 0 C IP54 1.2 kg

ART. NO. 1270603 VERTICAL MOUNTING ONLY

SERVOTEKNIKK DRAWN

CHECKED

IP40 0.2 kg

IP54 0.44 kg

1270610

1270611

FOR ENGINE ROOM AND HUMID AREAS

2002.04.20 SIZE

A4 DESIGN SCALE

Page 42

WB4

ALARM BELL MSB6B24

DATE

ST

KB-46

FILE :

REV.

1270603E MSB6B24 SHEET

1

OF

1


Alarm ligh for accomodation, type L101

DIMENSIONS

A

A

86.0

A

ø6.5

A

A

83.0

86.0 98.0

A - Cable entry ø20.0

CONNECTIONS

+ -

Alarm light (rear side)


+ -

SPECIFICATIONS L10124

TECHNICAL DATA OPERATING VOLTAGE CURRENT - ALARM

24 VDC 300 mA

OPERATING TEMPERATURE HUMIDITY FLASH FREQ./ENERGY

- 25 to + 55 0 C 0 - 90 % at + 50 0C 60 flash/min - 5 J IP55

PROTECTION WEIGHT ART.NO.

SERVOTEKNIKK DRAWN

CHECKED

ALARM LIGHT 24VDC 24VDC RED TYPE L10124

DATE

ST

180 g 1270660

2002.04.21 SIZE

A4 DESIGN SCALE

FILE :

REV.

1270660E L10124 SHEET

1

OF

1


Page 43

Alarm siren for engine room, type SEC-1992/24

DIMENSIONS

Art.no. 1270652 Art.no. 1270653

Art.no. 1270651

63.0

90.0

P

P = 2 x HOLES FOR PG13.5

92.0

92.0

TONE PROGRAMMING No.

MOUNTING

ø5.5 92.0

Base

CONNECTIONS

50.0

TONE

2nd

CODE

mA dB/1m

1

ALT TONES 800/970Hz - 1/4Hz

14

1 1 1 1 1 18

104

2 3 4

SWEEPING 800/970Hz - 7Hz SWEEPING 800/970Hz - 1Hz CONTINUOUS 2850Hz

14 14 14

1 1 1 1 0 19 1 1 1 0 1 18 1 1 1 0 0 29

105 105 116

5 6

SWEEPING 2400 / 2850Hz - 7Hz SWEEPING 2400 / 2850Hz - 1Hz

4 4

1 1 0 1 1 23 1 1 0 1 0 23

114 113

7 8 9

SLOW WHOOP SWEEP 1200 / 500Hz - 1Hz ALT TONES 2400 / 2850Hz - 1Hz

14 14 4

1 1 0 0 1 15 1 1 0 0 0 16 1 0 1 1 1 27

103 103 113

10 11 12

INT. TONES 970Hz - 1Hz ALT. TONES 800 / 970Hz - 1Hz INT. TONES 2850Hz - 1Hz

14 14 4

1 0 1 1 0 12 1 0 1 0 1 18 1 0 1 0 0 20

106 105 116

13 14

970Hz / 1 sec.. ON - 1.0 sec. OFF CONTINUOUS 970Hz

14 14

1 0 0 1 1 7 1 0 0 1 0 20

102 107

15 16 17

554Hz - 100ms / 440Hz - 400ms INT. 660Hz - 150ms / ON-OFF INT. 660Hz - 1.8 sec. / ON - OFF

14 16 17

1 0 0 0 1 12 1 0 0 0 0 9 0 1 1 1 1 12

99 87 91

18 19

INT. 660Hz - 6.5 sec. ON / 13 sec. OFF CONTIUOUS 660Hz

18 19

0 1 1 1 0 10 0 1 1 0 1 14

90 90

20 21 22

ALT. 554Hz / 440Hz - 1Hz INT. 660Hz - 1HZ INT. 2850Hz - 15ms ON / 100ms OFF

20 21 22

0 1 1 0 0 13 0 1 0 1 1 9 0 1 0 1 0 19

95 87 113

23 24

SWEEP 800 - 970Hz - 50Hz SWEEP 2400 - 2850Hz - 50Hz

23 24

0 1 0 0 1 18 0 1 0 0 0 22

105 112

- 2nd SOUND - 1st SOUND + COMMON +

SPECIFICATIONS Next alarm bell or end-of line resistor -

+

Volum adjustment Dip switch Signal programming programming

Terminal inlet

+

TECHNICAL DATA

SEC-1992

OPERATING VOLTAGE

24VDC

SEC-1992WT SEC-1992 24VDC

230 VAC

CURRENT (nom.) 30 mA START CURRENT (4ms) 75 mA

30 mA 75 mA

30 mA 75 mA

VOLUME CONTROL OUTLET SIGNALS ENVIRONMENT TEMP.

Pot.meter DIP switch -40 to +85 0 C



PROTECTION WEIGHT

IP43 3 60 g

IP65 3 60 g

IP65 3 60 g

ART. NO.

1270651

1 2 7 0 65 5 2

1 2 70 6 5 3

-


SERVOTEKNIKK DRAWN

ALARM SIREN SEC-1992

DATE

ST CHECKED

FOR HUMID (IP65) AND DRY (IP43) AREAS

2 0 0 2 .0 4 . 2 1 SIZE

A4 DESIGN SCALE

Page 44

REV.

FILE :

1270652E SEC1992 SHEET

1

OF

1


Door holder with magnet, type GPT-AG


42.0

ø6.3

52.0

116.0 MAN. RELEASE BUTTON

PLASTIC GLANDS (PG11)

PLASTIC GLANDS (PG11)

40.0

ø6.3 60

60.0

0

40.0

50.0

60.0

SPECIFICATIONS

CONNECTIONS GPT

Door magnet outlet 24VDC from panel

+ -

+ -

Next door magnet

TECHNICAL DATA

GPT-AG

OPERATING VOLTAGE CURRENT CONSUMPTION

24 VDC 40 mA

HOLDING POWER ENVIRONMENT TEMP. PROTECTION

650 N -10 to +70 0 C

WEIGHT magnet WEIGHT holder

750 g 75 g

ART. NO. magnet

1270452 1270455

ART. NO. holder

SERVOTEKNIKK DRAWN

CHECKED

DOOR MAGNET WITH HOLDER TYPE GPT-AG

DATE

ST

IP42

2002.04.20 SIZE

A4 DESIGN SCALE

FILE :

REV.

1270452E GPT-AG SHEET

1

OF

1


Page 45

COMMISSIONING Start the system During the installation of the system both power supplies (mains and battery) must be disconnected. When all cables for the fire alarm system is connected to the main panel, the system can be started by following the Functional test procedure (fuses location on terminal terminal board, see Connection cabinet lay out) : - remove the mains fuse (M) from the fuse holder on the main board - connect mains 230 VAC to the terminal inlets (28/29) - measure mains voltage and battery voltage on the terminal inlets - insert the mains fuse (M) - locate the battery fuse in the zip bag and insert it into the battery fuse holder (B) The panel should now be in normal operation and o nly the green LED POWER should be lit.

Functional test To ensure that the fire alarm system operates correctly, a complete test should be carried out when the panel/system is started for for the first time. NOTE! The panel outputs may may have been specially programmed. programmed. Verify correct operation according according to programmed parameters. parameters. - Press the button LAMP TEST. All LEDs on the front panel are lit - Check all detectors on all loops. Smoke detectors are tested by a test gas delivered by Servoteknikk. Heat detectors are tested by a hair drier and the manual call points are tested by a test key (supplied). If a bilge detector is connected to loop 4, the detector is tested by pressing and holding the test push button for minimum 1 minute. NOTE! A fault fault condition in a smoke or heat detector is shown with with a flashing indicator lamp, smoke detector with 1 Hz and heat detector with 0.2 Hz. For each test, check the following functions : The lamp FIRE on the front panel flashes, the lamps for Zone 1-4 are lit and the internal buzzer sounds. The indicator lamp on the activated detector illuminates. All alarm bells operate correctly (as programmed) and with sufficient sound level. All fire doors close during fire alarm (as programmed). External equipment (i.e. ventilation) connected to the control outlet operates correctly (as programmed). The acoustic alarm is cancelled by pressing the key ALARM SILENCE. By pressing the key PANEL RESET, the panel returns to normal operation. The panel is now in normal operation and only the lamp POWER is lit.

Page 46

Yearly testing and servicing The complete fire alarm system (panel, detectors, alarm bells/sirens and control functions) should be tested at least once a year by approved personnel. The test is performed as follows :

- Press LAMP TEST. TEST. Check that all lamps on the front panel are lit. - Press all keys on the front panel, one by one, and check that a short beep i s heard for each key. - Check that all alarm bells operate correctly by activating a manual call point. - Check all detectors visually for faults. Each detector has a self check system for fault condition which is indicated by a flashing lamp on the detector (SSD521 with 1 Hz and UTD521 with 0.2 Hz). All manual call points and detectors in each zone must be inspected. - Activate at least one detector or manual call point on each zone/loop. Check that all control functions operate correctly. - Check the fault warning by removing one detector head from its base for each zone. - Check the charging voltage for the batteries on outlet 15 and 16 on th e main board terminal (Door magnet outlet). The charging voltage should be in the range 26.6 – 27.6 Volts by 20 – 25 degrees Celsius (the charging voltage is temperature controlled and must not be adjusted as long as it is within this range !). - The batteries must be replaced every four years. See description in section ‘ Change batteries’. - The test is complete. Only POWER is lit. If a non-repairable fault is detected, please contact Servoteknikk for qualified service.

Maintenance It is important that the system is always fully in order. This can be ensured by careful maintenance and regular tests. The following operations should be carried out by a p erson who is appointed and trained to be responsible for the system : A.

Panel Ensure that the fire alarm panel is undamaged and kept clean. Make sure that the panel always is easily accessible.

B.

Detectors Accumulating dust and paint in smoke smoke detectors may cause false alarms. If a detector is faulty, faulty, the LED on the smoke detector SSD 521 flashes with 1 Hz and the heat detector UTD 521 flashes with 0,2 Hz. Therefore, check the detectors at regular intervals and replace them with new as required. Replace malfunctioning detectors as soon as possible. Make sure that furnishing, storing etc. have not reduced the open space under the detectors to less than 0.5 meters. If a bilge detector is connected to zone 4, check the movable parts of the detector and the connection box for corrosion of terminals.

C.

Manual Call Points Ensure that manual call points are not painted over, damaged or dusty. Check the glass covers of all manual call points. Replace broken or removed glass covers immediately. Make sure that all callpoints are visible and easily accessible.

D.

Alarm Units Ensure that all alarm bells, sirenes, and alarm lights are undamaged and clean. Test them regularly.

E.

Functions test All components must always be in order for the functions test commences. Refer to the section ‘COMMISSIONING ‘COMMISSIONING:: Functional test-Panel/System’. test-Panel/System’.

Page 47

Spare parts Art. No

Type

Description

1275200 1275201 1275200 1275200 1275221 1275181 1275182 1275229 1270443

Mains fuse (M) Battery fuse (B) Alarm outlet fuse (A1-A2) Door magnet fuse (D) End-of-line resistor SLP-99940 SLU-99950 RT050-1024 26V 50VA HV5-12

1.0AT (5x20mm) 2.0AT (5x20mm) 1.0AT (5x20mm) 1.0AT (5x20mm) 5.6 kohm, ¼ W Main board operating unit Main board connection unit Mains transformer Battery 12V-5Ah

Fault finding Any faults must be corrected immediately. Use the following procedures for locating and correcting the faults : System fault Take immediately contact with the manufacturer or his representative for repair. The fire alarm panel is nonfunctional! Mains fault a.Check the supply voltage at the terminals (inlet and transformer primary) - U = 230 VAC. b. Check the mains fuse (M) 1.0 AT (5x20mm) and the supply cables cables to the panel If these points are in order, the fault may be internal, and the circuit board must be replaced. NOTE: If the panel is supplied from from an external 24 VDC supply through a DC/DC DC/DC converter, check the converter input voltage (22-28 VDC) and the converter output voltage (nominally 32 VDC). Battery fault a.Check the supply voltage at the battery poles – it should be within the range of 26.6 to 27.6 Volts. b. Check the battery fuse (B) 2.0 AT (5x20mm) and the battery cables cables in the panel If these are in order, the fault may be internal, and the circuit board must be replaced. Earth fault An earth fault is likely to occur outside the panel. The following method of elimination is used to locate the fault: Remove the wires for Zone 1 and press PANEL RESET. If the fault disappears , the faulty outlet is found. Repeat for Zone 2, 3 and 4, General alarm, alarm, Alarm outlet 1 and 2, and Door outlet. Check the insulation between the voltage regulator IC and the heat sink rail (inside the cabinet). If these are in order, the fault may be internal, and the circuit board must be replaced. Zone fault / General alarm circuit fault a. Remove the zone cables from from the terminals. Connect a 5.6 kohm resistor over the terminals and reset the panel. If the fault reappear, the circuit board must must be replaced. If the fault does not reappear, reappear, continue tob. b. Short the end of line resistor. Measure Measure the loop resistance with a universal instrument. instrument. The resistance should not exceed 100 Ohms. The fault may be due to a broken wire or bad connection. Alarm outlet fault / Door outlet fault a. Check the the fuse fuse (A1 / A2) and and fuse fuse (D). (D). 1 AT (5x20 (5x20 mm). mm). b. An alarm device connected with with wrong polarity will cause a fault indication. Verify Verify correct polarities. c. Remove the alarm alarm outlet cables from the terminals. terminals. Connect a 5.6 kohm resistor over the terminals terminals and reset reset the panel. If the fault reappears, the circuit board must be replaced. If not, continue t oc. d. Measure the circuit resistance with a universal universal instrument. instrument. Note the value. Reverse the polarity and measure the again. The highest value is used. If the measured resistance lies outside 5k5 < R < 5k8 , there must be a break in the cables, a poor connection or a short circuit.

Page 48

Replacing the batteries 1.

Open Open the the pane panell fron frontt by by rem removin oving g the the four four bolt bolts. s.

2.

Disconnect Disconnect mains mains 230 VAC from the inlet inlet and and remove remove all all wires wires from from the the battery battery poles. poles. NOTE! Observe Observe and note down the colours and positions of the wires!

3.

Loosen the the circuit circuit board board from the battery battery bracket bracket (3 screw screws) s) and from from the heat heat sink rail rail (3 screws screws). ). Lift the the circuit board carefully and bend it over the cable harness.

4.

Remove Remove the battery battery bracket bracket by removing removing the screw screwss and spring spring washers washers (use (use a magnetic magnetic screw screwdriver driver), ), and lift the complete unit with batteries out of the cabinet. Be careful not to short circuit the batteries!

5.

Install the new batteries into the battery bracket bracket with the poles pointing outwards and towards towards the cabinet bottom. Fasten the complete unit in the cabinet with with screws and spring washers. washers. Use caution!

6.

Place the circuit board carefully back on top of the battery bracket and align the holes to the threaded studs. Fasten the circuit board.

7.

Connect the battery poles exactly as noted down. Reconnect Reconnect mains mains 230 VAC. Press LAMP TEST, and verify that the LEDs are lit.

8.

Mount the panel panel front front by by placing placing the the front front on the cabinet cabinet and fasten fasten it with with the bolts.

Procedure for battery replacement with former circuit board (circuit board marked SLU-99950-3):

1.

Open Open the the pane panell fron frontt by by rem removin oving g the the four four bolt bolts. s.

2.

Disconnect Disconnect mains mains 230 VAC from the inlet inlet and and remove remove all all wires wires from from the the battery battery poles. poles. NOTE! Observe Observe and note down the colours and positions of the wires!

3.

Remove Remove the voltage voltage regulato regulatorr clip from from the heat heat sink rail rail and loosen loosen the regulat regulator or carefully carefully from from the the rail.

4.

Loosen Loosen the circuit circuit board board from the battery battery bracket bracket by remov removing ing all six six screws screws with their their serrated serrated washer washers. s. Lift the circuit board carefully and bend it over the cable tree.

5.

Remove Remove the battery battery bracket bracket by removing removing the screw screwss and spring spring washers washers (use (use a magnetic magnetic screw screwdriver driver), ), and lift the complete unit with batteries out of the cabinet. Be careful not to short circuit the batteries!

6.

Install the new batteries into the battery bracket bracket with the poles pointing outwards and towards towards the cabinet bottom. Fasten the complete unit in the cabinet with with screws and spring washers. washers. Use caution!

7.

Bend the circuit board carefully back on top of the battery bracket and align the holes to the threaded studs. Fasten the circuit board with the screws and the serrated washers.

8.

Fit voltage voltage regulat regulator or on the the circuit circuit board board against against the the heat sink rail, rail, and snap snap the mounting mounting clip clip into place. place. NOTE! Make sure sure the insulating washer is in place between the regulator regulator and the heat sink rail. Otherwise the panel will have an earth fault!

9.

Connect the battery poles exactly as noted down. Reconnect Reconnect mains mains 230 VAC. Press LAMP TEST, and verify that the LEDs are lit.

10. Mount the the panel front front by placing placing the the front on on the cabinet cabinet and fasten fasten it with with the bolts. bolts.

Page 49

Modification for 24VDC supply 1. 2. 3. 4. 5. 6. 7. 8.

Remove the transformer cables (both primary and secondary) from the terminals on the main p.c. board and insulate the cable ends. Mount a PG13.5 cable gland outside on the panel cabinet (upper right side). Mount the DC/DC converter where suitable. Remove the DC/DC converter built-in fuse. Install a two wire cable between the converter and the panel. Insert the new cable through the cable gland into the panel. Dismantle the cable, mount end sleeves and connect the wires to th thee terminals for the transformer secondary outlet (unpolarized). Install a two wire cable between the converter and the shipboard 24VDC supply. Observe polarity. Reinstall the fuse in the DC/DC converter.

ServoFighter C4 should now be in normal operation and only the lamp Power should be lit.

PROGRAMMING By delivery ServoFighter C4 operates according to a standard program. Changing to another standard program and/or customising a program can only be done according to specified instructions given by Servoteknikk. The following standard programs are available :

Standard programs Deliv. Progr.

X

No

Type

Loops

Bells by fire alarm

Function for GENERAL ALARM

1 2 3 4 5

LAND LAND SHIP SHIP SHIP

1.6 sec. ON / 1.6 sec. OFF 1.6 sec. ON / 1.6 sec. OFF Continuous Continuous 1.6 sec. ON / 1.6 sec. OFF

Monitored alarm sender School bells Gen. alarm – 7S/1L Gen. alarm – fast Gen. alarm – 7S/1L

6 7 8

SHIP SHIP SHIP

4 loops 4 loops 4 loops 4 loops 3 loops – 1 bilge 4 loops 4 loops 4 loops

Continuous Continuous 1.6 sec. ON / 1.6 sec. OFF

Gen. alarm – 7S/1L Gen. alarm – 7S/1L Gen. alarm – 7S/1L

Delay for Delay Selection of alarm bells manual std. customer call points program 010 101 Enter 010 202 Enter 2 minutes 010 303 Enter 2 minutes 010 404 Enter 2 minutes 010 505 Enter 2 minutes

2 minutes

010 606 Enter 010 707 Enter 010 808 Enter

(Standard program 7 is normally installed from the factory.)

Select number of operator panels Changes in number of operator panels can be carried out by the installer according to the following procedure : - Key in 020 114 and confirm with ENTER: One operator panel - Key in 020 226 and confirm with ENTER: Two operator panels - Key in 020 338 and confirm with ENTER: One operator panel and one remote panel A correct operation is confirmed by a short beep. A rejected operation is indicated by a long beep. Try again.

Select bilge detector It is possible to connect a bilge detector to zone 4. Follow this procedure to program the zone for this purpuse: - Key in 050 440 3 and confirm with ENTER:

Page 50

Zone 4 with bilge detector (ship)

Page 51

Servoteknikk ServoFighter C4 Fire Alarm Panel Instruction Manual

Recommend Documents