A 15 in. diameter fan operates at 1600 rpm and develops a head of 6 in. of water and delivers 120 cfm. What volumetric capacity for geometrically similar fan that will develop 6 in. of water at 1300 rpm? A. B. C. D.
147.70 cfm 181.8 cfm 97.5 cmf 79.2 cfm
Answer: B
A radial-flow pump operating at maximum efficiency at a specific speed of 2500 is to deliver 260 gpm against a heat of 129 ft at a rotative speed of 2100 rpm. Find the required number of stager (i.e., impellers) A. B. C. D.
2 stages 3 stages 4 stages 5 stages
Answer: C
How many identical turbines, operating at 139.0 rpm at 191% efficiency (specific speed = 5.4), are needed to exploit a head of 1200 ft and a flow of 1660 ft/s. A. B. C. D.
2 turbines 3 turbines 4 turbines 5 turbines
Answer: B
How many poles a should a 60-Hz generator have, if it is connected to a turbine operating under a design head of 3000ft with a flow of 82 cfs? Assume turbine specific speed and efficiency 3 and 84 percent respectively. A. B. C. D.
10-pole 12-pole 14-pole 16-pole
Answer: D
It is proposed to build a dam in a river where the flow rate is 10 m3/s and a 32m drop in elevation can be achieved for flow through a turbine. If the turbine is 82 percent efficient, what maximum power that can be achieved? Specific gravity of river water is 0.998 A. B. C. D.
2570 kW 3133 kW 3820 kW 262 kW
Answer: A What type of turbine delivers 25,000 bhp at 500 rpm under a net head of 5350 ft A. B. C. D.
Impulse turbine Francis turbine Kaplan turbine Propeller
Answer: A 26-Hp pump delivers 475 gpm of gasoline (γ=42.5 lb/ft3) at 200C with 78% efficiency. What pressure rise result across the pump? A. B. C. D.
30.2 psi 32.7 psi 120.3 psi 73.2 psi
Answer: D A model pump delivering water at 1800F (γ=60.6 lb/ft3 ; ρ=7.54 psia) at 900 gpm and 2500 rpm begins to cavitate when the inlet pressure and velocity are 13 psia and 22 fps. Find the required NPSH of a prototype which is 4 times larger and runs at 1100 rpm. A. B. C. D.
63.5 ft 20.49 ft 6.61 ft 36 ft
Answer: A
The diameter of the discharge pipe is 8 in and that of the intake pipe is 10 in. the pressure gage at discharge reads 32 psi, and vacuum gage at the intake reads 12 in Hg. If the discharge flow rate = 4.0
ft3/s of water and the brake horse power is 49.0, find the efficiency. The intake and the discharge are at the same elevation. A. B. C. D.
82.1 % 80.9 % 55.8 % 58.46 %
Answer: A A piston positive-displacement pump (PDP) has 6-in diameter and a 2.5 in stroke. Its crankshaft rotates at 300 rpm. Calculate its output at 94 percent volumetric efficiency. A. B. C. D.
12.27 cfm 13.5 cfm 10 cfm 11.53 cfm
Answer: D A centrifugal pump (efficiency 88%) lifts water through a total height of 40m from reservoir to discharge. Pumping is through 300 m of 75 mm diameter pipe at the rate of 20 liters/sec. if pipe friction factor, f=0.025, what horsepower is required? A. B. C. D.
28.4 kW 32.2 kW 25 kW 9 kW
Answer: B
In order to predict the behavior of a small oil pump, test are to be made on a model using air, the oil pump is to be driven by a 1/20-hp motor a t 1800 rpm and ¼-hp motor is available to drive the air pump at 600 rpm. Using specific gravity of oil at 0.912 and density of air constant at 0.076 lb/ft3, what size model should be built? A. B. C. D.
The model should be 2 times as large as the oil pump The model should be 5 times as large as the oil pump The model should be 8 times as large as the oil pump The model should be 10 times as large as the oil pump
Answer: D
A double-overhung impulse-turbine installation is to develop 20,000 hp at 275 rpm under a net head of 11,000 ft. determine the specific speed. A. B. C. D.
4.34 6.14 203.61 144
Answer: A An impulse wheel at best produces 125 hp under a head of 210 ft. by what percent should the speed be increased for a 290-ft head? A. B. C. D.
82.5 % 17.5 % 72.41 % 71.59 %
Answer: B What is the power ratio of a pump and its 1/5 scale model if the ratio of head is 4 to 1? A. B. C. D.
20 200 12.5 125
Answer: B The speed of a centrifugal pump is doubled. By what factor does the pump head change? A. B. C. D.
0.125 0.25 4 8
Answer: C A 650 BHP diesel engine uses fuel oil of 280API gravity, fuel consumption is 0.65 lb/BHP-hr. Cost of fuel is P 7.95 per liter. For continuous operation, determine the minimum volume of cubical day tank in cm3, ambient temperature is 450C. A. B. C. D.
4,372,890 cm3 5,987,909 cm3 5,291,880 cm3 7,352,789 cm3
Answer: C A typical industrial fuel oil, C16H32 with 20% excess air by weight. Assuming complete oxidation of the fuel, calculate the actual air-fuel ratio by weight. A. B. C. D.
17.56 kgair/kgfuel 15.76 kgair/kgfuel 16.75 kgair/kgfuel 17.65 kgair/kgfuel
Answer: D Fuel oil in a day tank for use of an industrial boiler is tested with hydrometer. The hydrometer reading indicates a S.G. = 0.924 when the temperature of the oil in the tank is 350C. Calculate the higher heating value of the fuel. A. B. C. D.
43,852.13 kJ/kg 53,853.13 kJ/kg 58,352.13 kJ/kg 48,352.13 kJ/kg
Answer: A A diesel electric plant supplies energy for Meralco. During a 24 hr period, the plant consumed at 700 gallons of fuel at 280C and produce 3930 kW-hr. industrial fuel used is 280API and was purchased at P 5.50 per liter at 15.60C. What should the cost of fuel be produce one kW-hr? A. B. C. D.
1.05 1.10 1.069 1.00
Answer: A A certain coal has the following ultimate analysis: C = 70.5%
H = 4.5%
O2 = 6%
S = 3.0 %
Ash = 11%
Moisture = 4%
N2 = 1.0%
A stoker fired boiler of 175,000 kg/hr steaming capacity uses this coal as fuel. Calculate the volume of air in m3/hr with air at 600F (15.60F) and 14.7 psia (101.325 kPa) the coal is burned with 30% excess air. Boiler efficiency of 70% and factor of evaporation of 1.10. A. 212,861.04 m3/hr B. 221,861.04 m3/hr C. 218,261.04 m3/hr
D. 281,261.04 m3/hr Answer: A A diesel power plant consumed 1m3 of fuel with 300API at 270C in 24 hrs. Calculate the fuel rate in kg/hr. A. B. C. D.
36.21 26.25 29.34 39.42
Answer: A A diesel power plant uses fuel with heating value of 43,000 kJ/kg. What is the density of the fuel at 250C? A. B. C. D.
840 kg/m3 873 kg/m3 970 kg/m3 940 kg/m3
Answer: C A water tube boiler has a capacity of 1000 kg/hr of steam. The factor of evaporation is 1.3, boiler rating is 200%, boiler efficiency is 65%, heating surface area is 0.91 m2 per bo. HP, and the heating value of fuel is 18,400 kCal/kg. the total coal available in the bunker is 50,000 kg. Determine the no. of hrs to consume the available fuel. A. B. C. D.
853.36 hrs 706.57 hrs 979.46 hrs 100.75 hrs
Answer: A Two boilers are operating steadily on 91,000 kg of coal contained in a bunker. One boiler is producing 1591 kg of steam per hour at 1.2 factor of evaporation and an efficiency of 65% and another boiler produce 136 kg of steam per hour at 1.15 factor of evaporation and an efficiency of 60%. How many hrs will the coal in the bunker run the boilers If the heating value of coal is 7,590 kCal/kg? A. B. C. D.
230.80 hrs 280.54 hrs 350.35 hrs 300.54 hrs
Answer: A
The heating value of fuel supplied in a boiler is 40,000 kJ/kg. If the factor of evaporation is 1.10 and the actual specific evaporation is 10. What is the efficiency of the boiler? A. B. C. D.
62.07 % 53.08 % 78.05 % 54.97 %
Answer: A What is the rate of evaporation of a water tube boiler if the factor of evaporation is 1.10 percent rating of 200% and the heating surface area is 250 m2? A. B. C. D.
7,817.16 kg/hr 7,898.67 kg/hr 6,789.45 kg/hr 5,768.54 kg/hr
Answer: A Steam is admitted to the cylinder of an engine in such manner the average pressure is 120 psi. The diameter of the piston is 10 in. and the length of stroke is 12 in. What is the Hp of the engine when it is making 300 rpm? A. B. C. D.
171.4 Hp 175 Hp 173.2 Hp 174 Hp
Answer: A Steam enters a turbine stage with an enthalpy of 3628 kJ/kg at 70 m/s and leaves the same stage with an enthalpy of 2846 kJ/kg and a velocity of 124 m/s. Calculate the power if there are 5 kg/s steam admitted and the turbine throttle? A. B. C. D.
4597.45 kW 3976.55 kW 3883.81 kW 1675.42 Kw
Answer: C Compute the specific volume of an air-vapor mixture in cubic meters per kilogram of dry air when the following conditions prevail: t = 400C, w = 0.015 kg/kg, and Pt = 100 kPa. A. 0.99 m3/kg
B. 0.89 m3/kg C. 0.79 m3/kg D. 0.69 m3/kg Answer: A A coil has an inlet temperature of 700F and outlet of 800F. if the mean temperature of the coil is 1300F, find the bypass factor of the coil. A. B. C. D.
0.28 1.20 0.82 0.83
Compute the pressure drop of 350C al flowing a mean velocity of 5 m/s in a circular sheet-metal duct 400mm in diameter and 25m long. Use a friction factor, f = 0.04, and ρair = 1.3799 kg/m3. A. B. C. D.
431.22 Pa 221.34 Pa 312.24 Pa 422.31 Pa
Answer: A A 1.5 kg of wet stream at a pressure of 5 bar (h = 640 kJ/kg, h = 2109 kJ/kg) dryness 0.95 is blown into 70 liters of water of 120C (h = 50.4 kJ/kg). Find the final enthalpy of the mixture. A. B. C. D.
74.80 kJ/kg 84.80 kJ/kg 94.80 kJ/kg 104.80 kJ/kg
Answer: D The absolute pressure at a the bottom of a vertical column of water is 15.5 psia. What is the height of this column? A. B. C. D.
22 in 9.2 in 12 in 9.8
Answer: A Water temperature rise of 180F in the water cooled condenser is equivalent in 0C to
A. B. C. D.
7.78 0C 10 0C 263.56 0C -9.44 0C
Answer: B An oil storage tank contains oil with specific gravity of 0.88 and depth of 20 meters. What is the hydrostatic pressure at the bottom of the tank in kg/cm2? A. B. C. D.
1.67 1.76 1.56 1.87
Answer: B A vertical column of water will be supported to what height by standard atmospheric pressure? A. B. C. D.
34 ft 36 ft 24 ft 26 ft
Answer: A The specific weight of liquid is 60 lb/ft3 what is the equivalent to kN/m3 A. B. C. D.
9.334 9.249 9.643 9.420
Answer: D A cylinder weighs 15 lbf. Its cross sectional area is 40 square inches. When the cylinder stands vertically on one end, what pressure does the cylinder exert on the floor? A. B. C. D.
14.1 kPa 58.2 kPa 0.258 kPa 0.141 kPa
Answer: C What is the absolute pressure exerted on the surface of a submarine cruising 300 ft below the free surface of the sea? Assume specific gravity of sea water is 1.03
A. B. C. D.
133.9 psia 148.6 psia 100.7 psia 103.7 psia
Answer: B Air enters a nozzle steadily at 2.21 kg/m3 and 30 m/s. what is the mass flow rate through the nozzle if the inlet area of the nozzle is 80 cm2 A. B. C. D.
0.35 kg/s 3.5 kg/s 5.3 kg/s 0.53 kg/s
Answer: D The work required to accelerate an 800-kg car from rest to 100 km/hr on a level road: A. B. C. D.
308.6 kJ 806.3 kJ 608.3 kJ 386 kJ
Answer: A Assuming that there are no heat effects and no friction effects, find the speed of a 3220-lbm body after it falls 778 ft from rest. A. B. C. D.
422 ft/sec 424 ft/sec 224 ft/sec 424 ft/sec
Answer: C What is the flow rate through a pipe 4 inches in diameter carrying water at a velocity of 11ft/sec? A. B. C. D.
430.84 gpm 7.18 gpm 340.28 gpm 39.16 gpm
Answer: A The specific weight of a liquid is 58.5 lbf per cubic foot, what is the specific volume of the liquid cm3/g?
A. B. C. D.
0.5321 cm3/g 0.6748 cm3/g 0.9504 cm3/g 1.0675 cm3/g
Answer: D What is the resulting pressure when one pound of air at 0.3 psig and 2000F is heated at constant volume to 8000F? A. B. C. D.
0.572 psig 28.6 psia 7.857 psia 1.2 psig
Answer: B A small pump serving as model, when tested in laboratory using water at 3600 rpm, delivered 3.0cfs at a head of 125 ft. if the efficiency of this model pump is 84%. Predict the horse power input to the prototype pump if it is to develop the same head as model pump and the model pump has a scale ratio of 1:10. Assume the efficiency of the prototype pump 90%. A. B. C. D.
50.6 hp 4730 hp 4740 hp 60.5 hp
Answer: B Pump at its best efficiency point (BEP) has a capacity of 10,500 gpm while developing a head of 60 ft at a rotative speed of 1450 rpm. What is the specific speed of the pump? A. B. C. D.
2760 1450 2476 6892
Answer: D A pump will be installed below the reservoir water surface with a required net positive suction head (NPSHR) of 50 ft. the barometric pressure is 14.3 psia, and the vapor pressure is 0.5 psia. Assume friction losses in the intake piping are 5 ft. find the maximum allowable elevation of the pump relative to the water surface intake to avoid cavitation. A. 45 ft B. 55 ft
C. 18.2 ft D. 23.2 ft Answer: D Centrifugal pump at best efficiency (BEP). Assuming the pump characteristic are head, h = 7m, flow rate, Q = 19 liters/sec, and rotative speed n = 1170 rpm. Find the specific speed in SI units. A. B. C. D.
0.4 0.71 10.41 3.94
Answer: B
