PERODUA KELISA L701

��

��

��

��

USD 69.90 ��

��

�� Payment methods: 1. For buy with credit card just choose and click button at the end of price list in Product Item Number or click the the PayPal link down here first and signup now before make payment:

2. For online banking transfers, to verified your payment please give the Product Item Number, your e-mail (must valid to receive the download link), Name of Bank, Total of transaction, Date&hour of transaction and fill the form at contact form or send to [email protected]

Maybank Account Number:

Acc. Holder Name : DZULKIFLEE Acc. Number

: 152068638890

Bank Islam Account Number:


: 02039020168377

CIMB Bank Account Number:


: 02110042053522

You will receive the download link in 24hour after the payment verified from system admin. If any other problem about your payment system admin will contact you. Or you will reach us at: [email protected]

SERVICE MANUAL PERODUA

KELISA L701 FOREWORD

This service manual describes the maintenance and servicing procedures for the Model L701. In this service manual, the entire portion is divided into 20 sections. Each section has an index along with a table of contents at the beginning. For easier reference, the upper part of each page bears the section title concerned. All information used in this service manual was in effect at the time when the manual was printed. However, the specifications and procedures may be revised due to continuing improvements in the design without advance notice and without incurring any obligation to us.

Published in July, 2001

PERODUA SALES (M) SDN. BHD.

©

2001 PERODUA SALES (M) SDN. BHD. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of PERODUA SALES (M) SDN. BHD.

SECTION INDEX

PERODUA

SECTION NAME

KELISA

GENERAL INFORMATION MAINTENANCE ENGINE MECHANICAL EMISSION CONTROL EFI SYSTEM LUBRICATION SYSTEM COOLING SYSTEM IGNITION SYSTEM STARTING SYSTEM CHARGING SYSTEM CLUTCH MANUAL TRANSMISSION AUTOMATIC TRANSMISSION FRONT AXLE & SUSPENSION REAR AXLE & SUSPENSION BRAKE STEERING BODY BODY ELECTRICAL HARNESS &WIRING DIAGRAM

SECTION

GI MA EM EC EF LU CO IG ST CH CL MT AT FS RS BR SR BO BE HW

EM–9 REMOVAL 1. Remove the V-belt, water pump pulley and alternator. (Refer to the TIMING BELT section.) 2. Drain the engine coolant by removing the water pump drain plug. “

”

MEM00024-00024

3. Remove the timing belt. (Refer to the TIMING BELT section.) 4. Remove the camshaft timing belt pulley, using the SST to prevent the turning of the camshaft. SST: 09504-87501-000 “

”

MEM00025-00025

5. Remove the ignition coil from the cylinder head cover.

MEM00026-00026

6. Disconnect the vacuum hoses that are connected to the intake manifold and cylinder head cover. 7. Remove the surge tank stay from the cylinder head cover. 8. Remove the cylinder head cover attaching bolts in the sequence as indicated in the right figure. Remove the cylinder head cover from the cylinder head.

e

t

w

r

y

q

MEM00027-00027

9. Removal of camshaft bearing cap No. 1 and camshaft bearing cap No. 2. (1) Using the hexagonal section of the camshaft No. 2, set the mating marks of the camshaft gear sections to the relationship as indicated in the right figure.

Camshaft center line 10 - 20 ˚

˚

MEM00028-00028

IG–2 IGNITION SYSTEM CIRCUIT

Engine fuse 10A

Battery

Ignition switch 1

Ignitor

Ignitor

Ignition coil 1

Ignitor

Ignition coil 2

Ignition coil 3

To spark plug

46

68

67

IG1

IG2

IG3 ECU

E01

E1

N+

N-

18 15

36

60

Cam position sensor

MIG00002-00001

BR–2 INSPECTION AND ADJUSTMENT OF BRAKE PEDAL 1. Brake pedal height check (1) Check the pedal height. Specified Value RHD MT: MT: 148.0 ± 5 mm AT: 149.8 ± 5 mm LHD MT: 143.7 ± 5 mm AT: 148.4 ± 5 mm

e w

2. Pedal height adjustment (1) Disconnect the connector of the stop lamp switch. (2) Remove the stop lamp switch by loosening the lock nut 1. (3) Loosen the lock nut 2. Adjust the pedal height by turning the push rod 3. (4) Tighten the lock nut of the push rod. Tightening Torque: 22.6 - 28.4 N·m

q

T M T A

LBR00002-00001

(5) Screw-in the stop lamp switch, until it comes in contact lightly with the pedal stopper. (6) Adjust the clearance between the pedal stopper and the edge surface at the screw section of the stop lamp switch to 1.5 mm. (7) Tighten the lock nut of the stop lamp switch. Tightening Torque: 19.4 - 31.6 N·m (8) Connect the connector of the stop lamp switch. Ensure that the stop lamp goes on. LBR00003-00002

3. Pedal free travel check (1) After stopping the engine, depress the brake pedal several times so that no negative pressure may remain in the booster. (2) Lightly push the pedal by your hand. Measure the distance (free travel) up to a point where you feel a resistance from the pedal. Specified Value: 0.5 - 3.0 mm

LBR00004-00003

4. Pedal free travel adjustment (1) Loosen the lock nut 1. (2) Adjust the free travel to 0.5 - 3.0 mm by turning the push rod 2. (3) Tighten the lock nut. Tightening Torque: 22.6 - 28.4 N·m

w q

(4) Ensure that the stop lamp goes on properly.

LBR00005-00004

�� Payment methods: 1. For buy with credit card just choose and click button at the end of price list in Product Item Number or click the the PayPal link down here first and signup now before make payment:

2. For online banking transfers, to verified your payment please give the Product Item Number, your e-mail (must valid to receive the download link), Name of Bank, Total of transaction, Date&hour of transaction and fill the form at contact form or send to [email protected]

Maybank Account Number:


: 152068638890

Bank Islam Account Number:


: 02039020168377

CIMB Bank Account Number:


: 02110042053522

You will receive the download link in 24hour after the payment verified from system admin. If any other problem about your payment system admin will contact you. Or you will reach us at: [email protected]

��

��

��

��

PERODUA KELISA L701

Recommend Documents