4.7
Platform / Area nomenclature Guidelines: a. New platform or area which is similar to existing facilities facilities should carry carry the same same existing facility name by adding sequence number such as CSP, CSP-1 or NRP, NRP-1. b. New facilities with new operation operation concept should carry carry an abbreviated abbreviated name agreed between project project team and ESVT i.e. SARB, UL, GIF, GPF and TA …etc c. Area number number for all new facilities will be assigned assigned by Engineering Record officer.
5.
AVEVA PDMS
PDMS project folders, files, databases including any foreign project data, templates, reports and all relevant document/ information associated with the project shall be submitted to ADMA-OPCO. The PDMS environment shall be set-up in i n accordance with this document. 5.1
Project Set-up
PDMS System administration of the Project set up shall be documented in detail and submitted for ADMA-OPCO approval prior to t o modeling. This shall include all team names, user names & passwords, administration passwords, MDB/ database names/ numbers with description, design hierarchy & naming convention with description. All UDA’s required for the project shall be documented and submitted for ADMAOPCO approval. 5.2
Model Content
The individual areas of the detailed 3D model shall be the responsibility of the respective engineering/design disciplines. Each discipline shall define and document the items that are to be modeled in PDMS in their respective areas. Any exclusion to the model content is subject to written approval by ADMA-OPCO. The following shall be modelled as a minimum. •
1a.0 Rev.
Structure: Primary and secondary and tertiary steelwork (Columns, (Col umns, Beams, Bracings…) Joints complete with details. Floor, grating, plating and walls including penetration & sleeves and fireproofing. Jacket appurtenances, boat landing, riser fender, J-tube, Caissons, anodes… Stairs, ladders, access/ maintenance platforms, walkways, handrails and kick plates.
04-2012 Issued For Implementation. Implementation.
Date
Description / Text Affected
Codes Of Of Practices Practices For Plant Design - Part-1: Documentation Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 51
Structural supports and guides for equipment, piping, trays, ducts…. Equipment handling fixtures like crane, monorail, lifting hoist, pulley/ chain block… Installation aids i.e. lifting pad eyes/ trunnions…. •
Equipment:
Process and Utility equipment (to shape) shown on P&ID/ Equipment list including within package/ skid complete with appurtenances such as nozzles, hand hole, manway, covers, and davits… Major proprietary and ancillary items. Saddles, supports and any fixing mechanism. Door/ cover swing and access volume. Installation/ handling volumes and aids i.e. lifting li fting pad eyes/ lugs, slings... Jacket/ insulation volume complete with aids like l ike rings, cleats... Reinforcement items, platform/ support cleats. Reserved volume for withdrawal/ removal, operation/ maintenance/ access, dropout zone, handling space etc… Future equipment (Modelled in separate Zone). •
Piping:
All process, auxiliary and utility piping (including piping covered under legend drawing), piping within package/ skid (including vendor scope). Vessel trim, bridle complete with instrument. Inline items, fittings, accessories, special items, valves & instruments complete with manual/ gear/ actuated operators and space required for operation. Insulation, jacket as per specification. Vent, drain, instrument tapping/ connection, utility station. Pipe supports. Reserved volume for operation/ maintenance, removal and handling/ retrieving tools. Conductors/ risers. Bolt removal envelop to ensure no captive bolts and space for torqueing/ tensioning equipment. All future piping (Modelled in separate Zone). •
Electrical and Instrumentation:
All equipment e.g. generator, transformer, switchgear, MCC, LCS… Accessories for valve actuators. Cable trays/ ladders with support, J-Tube. 1a.0 Rev.
04-2012 Issued For Implementation. Implementation.
Date
Description / Text Affected
Codes Of Of Practices Practices For Plant Design - Part-1: Documentation Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 52
Electrical/ instrument panels & cabinets complete with door swing, maintenance/ access volume, stanchion…. Junction box, Marshalling box, Distribution box, termination box… Lighting fixtures, power sockets, switches, Nav-aid… Field instruments with support/ stanchion and shade. Radio mast/ tower. •
HSE:
All equipment i.e. Firefighting, safety, Lifeboat/ raft with davit, life buoy… Deluge/ Foam skid (with piping), deluge and sprinkler system with coverage envelop. Fire mains, fire hydrants/ monitors, hose reel.. Primary & secondary escape route/ volume with indicators/ signage and muster area. F&G detection, PA system, Telecom, CCTV, beacon, sounder… Maintenance/ operation/ access volume, lay-down & material handling volume, dropout zone, crane & lifting hoist movement area/ volume. Hatches, access openings with protective barriers. Safety shower, eyewash. •
HVAC:
All equipment e.g. Chiller, Air handling unit, Compressor unit, Window AC… All piping (i.e. chilled water, refrigeration) with inline items, accessories, instruments, valves, actuators… Ductwork with accessories, dampers, actuators, grilles.. Support for equipment, ductwork, piping. Duct and pipe insulation. Reserved space/ volume for maintenance, handling..
•
Architectural and Civil:
Foundations for structure & support, sleepers, piles, etc .. Building detailing doors and windows.
1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 53
5.3
Database and Naming
The project shall be split into Multiple Databases (MDB’s) based on Area for Das Island and Platform for Offshore. Area number shall be MDB Name. e.g.: MDB Name
08.3 201
MDB Description
Das - Zakum Separator Area ZWSC - Riser Platform
Each discipline shall be allocated databases based on the PDMS activity. Databases numbers shall be obtained from ADMA-OPCO. Database file number shall be same as database number. Sequential numbers shall be used without skipping except for temporary DB’s (which are to be deleted upon as built) which shall use end of the range, to maintain continuity of the numbers. Naming format of all administrative elements and databases with description to have a suitable convention. Details of the naming convention and coding explanations used to be submitted to ADMA-OPCO for approval. An example database name and description is given below for information only: DB Name: 201+DES+PIPE+01
e.g. 201DESPIPE01 = Serial Number (Incremental for same DB name) = Discipline Code = Database Type Code = Area number / MDB name DB Description: Piping Design DB for ZWSC - Riser Platform Database Type Code Data Base Type
1a.0 Rev.
Code
Data Base Type
Code
Design (DESI)
DES
Dictionary (DICT)
DIC
Draft (PADD)
DRA
ISODRAFT (ISOD)
ISO
Catalogue (CATA)
CAT
Schematic (SCHE)
SCH
Properties (PROP)
PRO
Engineering (ENGI)
ENG
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 54
Discipline Code Discipline
Description
Codes
Structure (offshore topside)*
Structural Discipline
STRU
Structure (offshore Jacket)*
Structural Discipline
JCKT
Civil
Civil
CIVL
Architecture
Architecture
ARCH
Support
Support
SUPP
Equipment
Mechanical Discipline
EQUI
Piping
Mechanical Discipline
PIPE
Instrumentation
Instrumentation Discipline
INST
Electrical
Electrical Discipline
ELEC
HVAC
HVAC
HVAC
Safety
HSE discipline
HSE
General
General Purpose
GEN
Catalogue
PDMS Administration Discipline
CATA
* Discipline code STRU & JCKT for offshore and STRU for onshore shall be used . 5.4
Catalogues and Specifications Naming
All items shall be named in accordance with the catalogues component naming convention as supplied with PDMS. There shall be project specific catalogue databases for components and/or data items that are created for the project. Catalogues and Specifications (e.g. Piping, Structural, etc.) shall be developed to ADMAOPCO standards and any deviations are to be noted and submitted to ADMA-OPCO for approval. 5.5
PDMS Design Hierarchy
PDMS Design Sites and Zones shall be named (as illustrated below) in a manner such that they can be easily identified and organised against plant area and discipline. Sites and Zones shall have their description and purpose attributes set to reflect their intended use. Naming format with description shall be submitted for ADMA-OPCO approval.
1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 55
•
Site Naming
Sites shall be created and named in line with the respective DB for all disciplines with the Datum Point and Purpose set for it. Site naming shall be in the following format: Site Name: =XXXPIPE Where PIPE =Discipline Code XXX =Area number/ MDB name e.g.: Site name for Piping in area 201 (ZWSC Riser Platform) shall be /201PIPE. •
Zone Naming
Zone naming will vary as per the discipline need. All zones created shall be named appropriately and to follow the explained convention. For offshore Zone naming is generally deck based and for Onshore it is based on type. •
Pipe Zone Naming
All pipes shall be modelled in proper zone which is based on process service code. The zone name shall be as follows: /201PIPE/NNNN
e.g. /201PIPE/CO Process Service Code Site Name (Area Number/ MDB name + Discipline Code) e.g.: Pipe having service code “CO” shall be created in zone /201PIPE/CO. Detailed hierarchy as follows: Site > /201PIPE Zone> /201PIPE/CO Zone> /201PIPE/LO Zone> /201PIPE/PW
•
> /CO-16”-AC0NA0-1234AD > /CO-18”-AC0NA0-2345AD > /CO-20”-AC0NA0-3456AD
Equipment Zone Naming
All mechanical equipment (with proper origin) shall be modelled under equipment zone. For offshore zones shall be deck based. Where equipment crosses into multiple decks it shall be modelled under deck on which it rests. The zone naming shall be as follows: For Onshore 08.3EQUI/NNNN
1a.0 Rev.
e.g.
/08.3EQUI/Static Equipment type: Static/ Rotating Site Name (Area Number/ MDB name + Discipline Code)
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 56
For Offshore 201EQUI/NNNN
e.g.
/201EQUI/Deck name Deck name (where necessary) Site Name (Area Number/ MDB name + Discipline Code)
Future equipment shall be created in separate zone as follows: / 201EQUI/FUTURE
e.g.
/201EQUI/FUTURE
Site Name (Area Number/ MDB name + Discipline Code) Detailed hierarchy as follows: /201EQUI/DECK NAME /201EQUI/PACKAGE:
For modelling Mechanical equipment. For modelling Mechanical package unit.
Detailed Hierarchy as follows: Site > /201EQUI Zone> /201EQUI/MAINDECK Zone> /201EQUI/PACKAGE /EQUI> /201-C-1234 /EQUI> /201-P-1234 /EQUI> /201-T-1234 /EQUI> /201-V-1234
NOZZ> /201-C-1234/N1 NOZZ> /201-C-1234/N2 SUBE> /201-C-1234/Platform-Clips SUBE> /201-C-1234/Ladder-Clips SUBE> /201-C-1234/Supp-Clips SUBE> /201-C-1234/Earthing-Boss SUBE> /201-C-1234/Name-Plate SUBE> /201-C-1234/Fixed-Saddle SUBE> /201-C-1234/Sliding-Saddle SUBE> /201-C-1234/Davit-XXX (Each davit to be SUBE and named appropriately) SUBE> /201-C-1234/Boot SUBE> /201-C-1234/Rein-Pad SUBE> /201-C-1234/Insulation SUBE> /201-C-1234/Access-Way/ Platform SUBE> /201-C-1234/Reserved-Volume SUBE> /201-C-1234/Reserved-Volume: Area /volume required/ reserved for operation and maintenance of the equipment. •
Nozzle Naming
Nozzle names shall be equipment tag/nozzle number. e.g. /201-C-1234/N1
1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 57
•
Civil/Structure Zones:
Zone naming for Civil/ Structure for Offshore shall be deck based and as follows: For Onshore Zone naming, sub division shown under deck shall be used (e.g.: STRUCTURE, LAD-STAIR, HANDRAIL …).
/201STRU/HELI DECK /201STRU/VALVE ACCESS DECK /201STRU/MAIN DECK /201STRU/CELLAR DECK Detailed Hierarchy as follows: Site > /201STRU Zone> /201STRU/MAIN DECK structure.
Deck Code shall be used at /STRU> level and below /STRU>MDK/STRUCTURE For modelling main
/STRU>MDK/LAD-STAIR /STRU>MDK/HANDRAIL /STRU>MDK/GRATING /STRU>MDK/SUPPORT
For modelling ladder & staircase. For modelling handrail. For modelling grating /flooring. For modelling all supports.
/FRMW>MDK/COLUMN /FRMW>MDK/BEAM /FRMW>MDK/BRACING Access/ Maintenance platforms shall be created at /STRU> level and named appropriately. All sections (SCTN) under framework shall be properly tagged. Items like stiffeners shall be clubbed together and created under sub-framework and tagged appropriately (as per the structure they belong to). Deck Codes:
1a.0 Rev.
Deck/ Area Level
Code
Deck/ Area Level
Code
Heli Deck
HED
Mezzanine Deck
MZD
Above Weather Deck AWD Valve Access Deck
VAD
Weather Deck
WED
Sub Cellar Deck
SCD
Solar Panel Deck
SPD
Sump Deck
SDK
Main Deck
MDK
Jacket Walkway and Boat Landing
BLL
Cellar Deck
CDK
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 58
Similar convention shall be followed for Jacket. •
Electrical Zones
Zone naming for Electrical shall be as follows: /201ELEC/CABLE_TRAY-HI: /201ELEC/CABLE_TRAY-LO: /201ELEC/EQUI-Deck Name:
For modelling Electrical high voltage cable tray. For modelling Electrical low voltage cable tray. For modelling Electrical equipment (Transformer, Panels, DB, Bus duct etc.) based on deck for offshore and one zone for onshore.
/201ELEC/SMALL-POWER-EQUIP:
For modelling Electrical lighting fixture & poles etc. For modelling Electrical heat tracing equipment.
/201ELEC/EHT-SYSTEM: Detailed Hierarchy as follows: Site > /201ELEC Zone> /201ELEC/CABLE_TRAY-HI Zone> /201ELEC/CABLE_TRAY-LO Zone> /201ELEC/EQUI-Deck Name
/PIPE> CABLE_TRAY-HI-150 /PIPE> CABLE_TRAY-HI-200 /PIPE> CABLE_TRAY-HI-300 /PIPE> CABLE_TRAY-HI-400
/STRU> DBs /STRU> RTU /STRU> PANELS /STRU> TRANSFORMER /STRU> SWITCH-GEAR All equipment shall be created with proper origin. •
Instrument Zones
Zone naming for Instrument shall be as follows: /201INST/F&G: /201INST/EQUI: /201INST/TEL-EQUIP: /201INST/MANIFOLD: /201INST/CABLE-TRAY: /201INST/V-BOTTLE:
For modelling fire and gas detector. For modelling instrument equipment. For modelling telecom equipment, CCTV, PA system. For modelling instrument air manifold. For modelling instrument cable tray. For modelling Volume bottle.
Detailed Hierarchy as follows: Site > /201INST Zone> /201INST/CABLE-TRAY 1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 59
Zone> /201INST/EQUI Zone> /201INST/CABLE-TRAY Zone> /201INST/EQUI /PIPE> CABLE_TRAY-150 /PIPE> CABLE_TRAY-200 /PIPE> CABLE_TRAY-300 /STRU> JBOX /STRU> MBOX /STRU> LOC-PANEL /STRU> ANA-PANEL /STRU> STANCHIONS All equipment shall be created with proper origin. •
Safety Zones
Zone naming for HSE shall be as follows: /201HSE/EQUI: /201HSE/ESCAPE-ROUTE: /201HSE/LAYDOWN: /201HSE/ACCESS:
For modelling firefighting & safety equipment. For modelling escape routes. For modelling laydown area. For modelling access and maintenance volume.
Detailed Hierarchy as follows: Site > /201HSE Zone> /201HSE/EQUI
/EQUI> Lifeboat-001(assigned tag shall be used) /EQUI> Lifebouy-001 All equipment shall be created with proper origin. •
Support Zones:
/201SUPP/PIPE /201SUPP/ELEC /201SUPP/INST /201SUPP/HVAC Detailed Hierarchy as follows: Site > /201SUPP Zone> /201SUPP/PIPE
/STRU>MDK/SUPP /STRU>VAD/SUPP /STRU>CDK/SUPP Deck Code shall be used at /STRU> level and below for offshore.
1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 60
•
Equipment Origin:
All equipment shall have a logical origin which can aid in its placement. Following are examples of origin for some equipment.
1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 61
VERTICAL VESSEL/ COLUMN/ CYCLONE
SHELL & TUBE EXCHANGER
ELEVATION
PLAN
CENTRELINE OF EXCHANGER & INLET/ OUTLET NOZZLES REBOILER
T/L
ELEVATION
ELEVATION
CENTRELINE OF TUBE BUNDLE & CENTRELINE OF TUBE INLET
CENTRELINE OF EQUIPMENT & BOTTOM TAN LINE
PLATE EXCHANGER
HORIZONTAL VESSEL
FIN-FAN COOLERS & CONDENSERS
S . S
S . F
PLAN
PLAN
PLAN
L / T
CL
C L
ISO VIEW
CENTRELINE & FLANGE FACE OF LOWER RIGHT HAND NOZZLE
1a.0 Rev.
ELEVATION CENTRELINE OF EQUIPMENT & TAN LINE NEAR FIXED S UPPORT
ELEVATION CENTRELINE & FLANGE FACE OF INLET NOZZLE
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 62
HORIZONTAL PUMP, BLOWER
VERTICAL PUMP
POSITIVE DISPLACEMENT PUMP
& FAN, HORZ. ROTARY EQUIPMENT & DRIVER
PLAN
PLAN
. H C S I D
CL
ELEVATION
ELEVATION
CENTRELINE OF PUMP & DISCHARGE NOZZLE
COMPRESSOR PACKAGE
ISO VIEW
CENTRELINE OF PUMP & DISCHARGE NOZZLE
CENTRELINE & FACE OF SUCTION FLANGE
SKID/PACKAGE
PRINTED CIRCUIT EXCHANGER
PLAN
PLAN
EL
ELEVATION CENTRELINE OF EQUIPMENT & BOTTOM OF BASE AT SOUTH OR WEST END
1a.0 Rev.
ISO VIEW
ELEVATION
BOTTOM OF BASE AT SOUTH WEST CORNER
CENTRELINE OF EQUIPMENT & TUBE INLET
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 63
PIG LAUNCHER
RECTANGULAR STORAGE
& RECEIVER
TANK OR VESSEL
PLAN
PLAN
PLAN
ISO VIEW
ISO VIEW
BOTTOM OF BASE AT SOUTH WEST CORNER
CENTRELINE OF EQUIPMENT & INLET NOZZLE
ISO VIEW CENTRELINE AT FACE OF FACE OF FLANGE
STORAGE TANK
VERTICAL SUBMERGED
FILTER/ STRAINER
LIFEBOAT & DAVIT
PUMP
ISO VIEW MID WAY BETWEEN SUPPORTS & TOP OF STEEL
PUMP
CRANE
MOTOR ISO VIEW CENTRELINE & BOTTOM OF BASE PLATE
CENTRELINE OF PUMP & DISCHARGE NOZZLE
ISO VIEW BASE OF PEDESTAL
For E&I Cabinets/ Panels -
1a.0 Rev.
Centre bottom of back side/ panel.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 64
5.6
Tagged Items
All tagged items shall be named as per their Tag ID as given on P&IDs, plot-plans, datasheets, lists, etc. and as per specified tagging philosophy. Any deviations shall be documented and submitted to ADMA-OPCO for approval. This applies to but is not limited to: a. b. c. d. e. f.
Equipment Nozzles Pipes In-line piping items, i.e. Orifice Plates, Instruments, Valves, Filters, etc. Steelwork i.e. columns, beams, stair, ladder, access platform etc. Electrical & Instrument Cable Tray, Equipment, i.e. Junction Boxes, Control Panels, etc. g. Supports 5.7
Pipe Supports
AVEVA Multi-Discipline Supports (MDS) software shall be used for the 3D design of all Pipe work supports in PDMS. The catalogue, specification, design and drawing databases for VPD-MDS that are used on the project complete with any modifications shall be submitted to ADMA-OPCO as part of the project deliverable. Support numbering shall comply with ADMA-OPCO numbering procedure. E.g. 201-PS-00001 = Sequence Number = Pipe Support = Area number/ MDB name PS = Pipe Support TS = Cable Tray Support SPS = Special Support 5.8
Colours
Colours specified in the following table which is basic identification colour (first band colour) specified in ADMA-OPCO painting manual MNL-01 shall be used for PDMS model, draft and review model.
1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 65
��� � ��������� ��� ��
�� ����� ����
���� ����� ������
�
����
����
����
����
������
�����
���
������
����
������
������
������
�
���
��������� � ������
�����
��
���
��������� � ����
�����
���
���
����� �������
�����
��
�
���
��� � �������
������
��
�
���
�������
����� ����
�
�
����
��
�
���,���, ���
��� � ����������
���
��������� � ���
���
��������� (������) ������ (������)
����� ����
��
���
���
�������� ���������, ������������
���������
��
���
1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 66
��� � ����������
���
�� ����� ����
���
���� ����� ������
����
����
����
����
������
�����
���
������
����
������
������
������
���
���������� ���� ������� ����� �����
���
��
�
���
��� ������� ����� ����
�������
��
�
���
���������� ��������� (������� ������)
����� ����
�
�
���
��
�
�
��� � ���������������
���
��������������� ���� � ������
������
���
���������� ��������� (������� ������)
����� ����
��� � ���
���
������ ���� ����� ����������� ������ �� � ����� ��������� & �� ������ �� ����������
���
������ ����
���
����� ��� ���������
���������
���
������ ��� ��������
���
���� �������� ����������
1a.0 Rev.
���
���
���
��
�
���
��
�
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 67
��� � ������
��� ���
�� ����� ����
���� ����� ������
����
����
����
����
������
�����
���
������
������
������
������
����
���
����� ��� (����)
�����
�
��
���
����� ��� (����������)
�����
�
��
���
����� ��� (������)
�����
�
��
���
��������� ���
�����
�
��
���
��������� ���
�����
�
��
���
���� ��� (���)
������
���
��
���
���� ��� (���)
������
���
��
������
���
��
������
���
��
��� ���
����� ��� (���) � ��� ��� ��� ����� ��� (���) � ��� ��� ���
����
����� ���
������
���
��
����
����������
������
���
��
����
��� ����������
������
���
��
����
���� ���
������
���
��
����
������ ����
������ �����
���
���
����
�������
������
���
��
����
����� ��� �� �����
������
���
��
����
�������� ���� ���
������
���
��
����
��� �� ����������
������
���
��
6.19
�����
����� ����
���
���
6.20
�������
����� ����
���
���
6.21
������
����� ����
���
���
6.22
��������
����� ����
���
���
6.23
������
����� ����
���
���
����
���������� ���
����� ����
160
142
����
���������� ���
����� ����
���
���
����
�������� ���
����� ����
���
���
����
������ �������
����� ����
���
���
����
���� �����
���
��
�
����
���� (���� ��������)
���
��
�
1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 68
��� ���
�� ����� ����
���� ����� ������
���� ������ ����
����
����
����
�����
���
������
������
������
������
����
����
�����
��
���
����
������� ����
�����
��
���
����
�����
����� ����
�
�
����
���� ����������
����� ����
�
�
����
������ ����
�����
��
�
����
�������� ����
�����
��
�
����
������� ����
�����
��
�
����
��������
�����
��
�
����
��������
�����
��
�
����
������ ���
�����
��
�
����
���� ���
�����
��
�
����
��������� ���
�����
��
�
����
��� �����
������ �����
���
��
����
��� �����
������ �����
���
��
����
���� �����
������ �����
���
��
����
������� �����
������ �����
���
��
����
������� �����
������ �����
���
��
����
������� �����
������ �����
���
��
����
������� �����
������ �����
���
��
����
��������� ��� �����
������ �����
���
��
6.50
������ ���� �����
������ �����
���
��
6.51
�������� �����
������ �����
���
��
6.52
������������ ��� �����
������ �����
���
��
1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 69
5.9
Draft Drawings Rules, Libraries, etc
All 2D Drawing Production Administration elements, e.g. Rules, Libraries, Templates, etc. shall be named and documented accordingly and submitted to ADMA-OPCO for approval. 5.10
Draft Drawing Databases Structure
Drawing databases shall be created in a structured manner to reflect the design areas and disciplines, consideration given to maximize drawing production. Drawings and Sheets shall be named/ numbered in accordance with ADMA-OPCO document/ drawing numbering procedure. All dimensioning & annotation shall be done in draft and shall be intelligent. The extent of annotation and quality of the drawing shall be as specified in CP-00 Part-3. Modifying/ editing drawings outside PDMS shall not be accepted. Zone based layers shall be created and all items within the zone shall be placed in the same layer. The 2D drawing representation within PDMS shall adhere to ADMA-OPCO standards and be subject to ADMA-OPCO approval. All drawings shall be fully updated to reflect the as-built 3D plant model upon completion of the project and prior to hand over. DWG and DXF format copy of all 2D project drawings produced within PDMS to be provided to ADMA-OPCO. •
Draft Naming Convention Drawing Type Code Drawing Type
Drawing Type Code
Section Discipline*
Plot Plan
DWG
L
General Arrangement Drawings
GAD
M
Section & Elevation Drawings
DWG
M
Miscellaneous Drawings
MIS
* Refer section discipline above
1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 70
Department Naming
•
Department Name = Discipline Code + Area Code + Platform Deck Code* Example:Discipline Code
Area Code
Platform Deck Code*
Department Name
PIPE
XXX
MDK (Main Deck)
/PIPEXXX-MDK
Registry Naming
•
Registry Name = Discipline Code + Area Code + Platform Deck Code* + Drawing Type Code Example:Discipline Code
Area Code
Platform Deck Code*
Drawing Type Code
Registry Name
PIPE
XXX
MDK (Main Deck)
GAD
/PIPEXXX-MDKGAD
* Platform Deck Code applicable to offshore only. For onshore use Elevations/ platform levels where required. •
Sheet Naming
Example:-
5.11
Project Code
Area Code
Section / Discipline Type
Drawing Number
ADXXX
XXX
M
20010
Draft Text and Colours •
Text font, sizes & colour
The text font (with width factor 0.85), size and colour specified in the table below shall be used for all engineering drawings and shall be in uppercase only. Exception to this shall be ADMA Border template where provided fonts and colours shall be retained. Prior approval shall be obtained for any deviation.
1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 71
Drawing Size Drawing Item
Text Height Text Font Text Colour Text Height Text Font Headings Text Colour Dimension Line Projection Line Leader Line LABEL frame Note line General Text
•
A0
A1
A2
A3
A4
3 mm Romans White 5 mm Romand White Red Red Red Red White
3 / 2.5 mm Romans White 5 mm Romand White Red Red Red Red White
2.5 mm Romans White 4 mm Romand White Red Red Red Red White
2 mm Romans White 3.5 mm Romand White Red Red Red Red White
2 mm Romans White 3.5 mm Romand White Red Red Red Red White
Drawing items colour coding and line thickness Drawing item
Drawing Type
Piping Drawing
Equipment Drawing
Structural Drawing Cable Tray Layout
5.12
Pipes Refer colour table Thick lines
Structure
Equipment Refer colour table Thin line Refer colour table
Cable tray
Other discipline
Grey
Grey
Thin line
Thin line
Grey
Grey
Grey
Grey
Thin line
Thin line
Thick line
Thin line
Thin line
Grey
Magenta
Grey
Grey
Grey
Thin line
Thick line
Thin line
Thin line
Thin line
Grey
Grey
Grey
Refer colour table
Grey
Grey Thin line
Piping Isometric Production and Control
Only complete lines with acceptable clash and data consistency to be submitted for isometric generation. Isometric option file(s) shall be created per MDB (Platform/ Plant/ Area) and shall be configured to reflect ADMA-OPCO standards. All process information/ parameters, test, heat treatment & painting requirement, insulation/tracing type & thickness, support location/ type with tag, reference to piping GA & P&ID, stress analysis requirement/ reference and detailing where required shall be provided in isometric along with BOM. Isometric drawing number shall reflect tag given in the design hierarchy which is the line tag as specified in `CP-00 Part-2 process and utility line tagging format’. 1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 72
As-Built Isometrics in DXF and PDF format to be delivered to ADMA-OPCO Please Note: Annotation/ editing of Isometrics outside of PDMS is not permitted unless approved in advance by ADMA-OPCO. 5.13
Reports
All reports and PDMS report templates generated for and used on the project shall be submitted to ADMA-OPCO. Reports shall be in MS Excel format. 5.14
Data Consistency Checking (Reports)
A final report showing all Pipes to be free of inconsistent data shall be delivered upon project completion. A final report showing all Structural items logically connected shall be delivered upon project completion. 5.15
Clash Checking (Reports)
A final report showing clash free design and approved clashes shall be delivered upon project completion. 5.16
Database Integrity (Dice Checking Report)
A final report showing all databases clean of errors shall be delivered upon completion of the project. 5.17
Miscellaneous
All PDMS database sessions shall be merged prior to submission. 5.18
Project Data
ADMA-OPCO may at any time request complete PDMS Project Data and/ or access to PDMS Project Data during Project execution. 5.19
Project Review
For periodic/ milestone and as-built review of the 3D PDMS model, latest colour review model with status file of the 3D PDMS model shall be provided. Review model (RVM & RVS) shall be made available to ADMA pri or to periodic/ milestone reviews. Colours specified in the table shall be used for review model.
1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 73
5.20
Aveva P&ID
The As-built AVEVA P&ID drawings along with all related database and project files shall be submitted to ADMA-OPCO upon project completion P&ID representation shall be in accordance with ADMA-OPCO standards. Symbols created for the project shall have a suitable naming convention and shall be submitted to ADMA for approval. Information detailing layer, line type, text font/ height, colour etc... for P&ID and PFD shall be submitted to ADMA for approval.
5.21
Milestone Requirements
At project milestones the following shall be delivered to ADMA-OPCO; a. P&IDs with .MON files b. P&ID Reports generated reports 5.22
Project Completion
Upon project completion the following shall be delivered to ADMA-OPCO; a. b. c. d. e. f. g. 6.
Project Set up & configuration Project Symbols Drawing Border Templates P&IDs with .MON files P&ID Reports MS Access database P&ID Reports generated reports Documented list of settings made to configure the VPE P&ID project.
END OF PROJECT DELIVERABLES:
At the end of the project, ADMA-OPCO’s, Engineering Services Team shall receive the following deliverables from the Contractor/Consultant through ADMA-OPCO’s Project Team Leader:6.1
One complete set of following Documents and Dossiers: a. Main index of project completion dossiers/drawings (Deliverable List) b. Engineering dossier consisting of all Specification, Calculation, Analysis, Data
sheets in its Native format c. Certification Dossier 1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 74
6.2
As-Built drawing folder in native files as applicable
6.3
Drawing List
6.4
Process: a. PFD’s b. P & ID’s
6.5
Mechanical a. Plot Plans b. Piping General Arrangement c. Vendor/ package GA’s (separate drawing for each package) d. Sections & Details e. Piping Isometric with BOM f.
Equipment Drawings (separate drawing for each equipment)
g. Line List h. Valve List i.
Equipment List
j.
MTO
k. Equipment and Valve Data Sheet (separate data sheet for each equipment and actuated/
safety valve). 6.6
Pipelines Drawing: a. Profile & Alignment Sheets b. Riser Details
6.7
Civil/Structural Drawing: a. Site Layout, Plot Plan b. General Arrangement c. Architectural Drawings d. Reinforced Concrete Detail
1a.0 Rev.
04-2012 Issued For Implementation.
Date
Description / Text Affected
Codes Of Practices For Plant Design - Part-1: Documentation & Archiving
ADMA-OPCO SF / General / 002 Rev.0 sheet 1 of 1
CP-00 Part-1
PAGE 75
