Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
PDMS DRAFT Administrator Application User Guide Version 11.6SP1
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1
1.8K views
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
PLEASE NOTE:
AVEVA Solutions has a policy of continuing product development: therefore, information contained in this document may be subject to change without notice.
AVEVA SOLUTIONS MAKES NO WARRANTY OF ANY KIND WITH REGARD THIS DOCUMENT, INCLUDING BUT NOT LIMITED TO, THE IMPL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU PURPOSE.
While every effort has been made to verify the accuracy of this document, AVE Solutions shall not be liable for errors contained herein or direct, indirect, spe incidental or consequential damages in connection with the furnishing, performanc use of this material.
This manual provides documentation relating to products to which you may not access or which may not be licensed to you. For further information on which Prod are licensed to you please refer to your licence conditions.
All rights reserved. No part of this document may be reproduced, stored in a retr system or transmitted, in any form or by any means, electronic, mechan photocopying, recording or otherwise, without prior written permission of AVE Solutions. The software programs described in this document are confidential information proprietary products of AVEVA Solutions or its licensors.
For details of AVEVA's worldwide worldwide sales and support support offices, see our website at http://www.aveva.com Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1
1.8K views
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
PLEASE NOTE:
AVEVA Solutions has a policy of continuing product development: therefore, information contained in this document may be subject to change without notice.
AVEVA SOLUTIONS MAKES NO WARRANTY OF ANY KIND WITH REGARD THIS DOCUMENT, INCLUDING BUT NOT LIMITED TO, THE IMPL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU PURPOSE.
While every effort has been made to verify the accuracy of this document, AVE Solutions shall not be liable for errors contained herein or direct, indirect, spe incidental or consequential damages in connection with the furnishing, performanc use of this material.
This manual provides documentation relating to products to which you may not access or which may not be licensed to you. For further information on which Prod are licensed to you please refer to your licence conditions.
All rights reserved. No part of this document may be reproduced, stored in a retr system or transmitted, in any form or by any means, electronic, mechan photocopying, recording or otherwise, without prior written permission of AVE Solutions. The software programs described in this document are confidential information proprietary products of AVEVA Solutions or its licensors.
For details of AVEVA's worldwide worldwide sales and support support offices, see our website at http://www.aveva.com Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Contents 1
About this Guide......................... Guide..................................... ....................... ....................... ....................... ....................... .................. ......
1.1 1.2 1.3
The Scope of this Guide ......................................................... ............................ ........................................................... .............................. How the Guide is Organised.................................................................................... Conventions Used in the Guide...............................................................................
2
Some General Principles............................................................................
2.1 2.2 2.3 2.4 2.5
The Role Role of the DRAFT Administrator............................. Administrator .......................................................... ........................................ ........... Setting Up Administrative Access Rights................................................................. Supplied Libraries.................................................................................................... Searching Libraries.................................................................................................. The DRAFT Default Files.........................................................................................
3
Setting the DRAFT Defaults ......................... ............ .......................... ......................... ......................... ..................... ........
3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10
Setting the System Defaults ......................................................... ........................... ......................................................... ........................... Saving and Loading Default Values......................................................................... Setting Layer Purpose Definitions ........................................................... ............................. .............................................. ................ Layer Creation Definitions ....................................................... ......................... ........................................................... ............................. Layer Purpose Filtering............................................................................................ Sheet Size Defaults ........................................................... .............................. ........................................................... ...................................... ........ Defining Element Naming Conventions................................................................... Defining Pen Drawing Styles ........................................................ ........................... ........................................................ ........................... Setting Plotting Options ........................................................... ............................. ........................................................... ............................. ADP Administration..................................................................................................
4
Selecting the Working Library .......................... ............. .......................... ......................... ......................... .............
4.1
Changing your Working Library .......................................................... ............................ ................................................... .....................
5
Sheet Library Administration.....................................................................
5.1 5.2 5.3 5.4
Entering the Sheet Library Library Administration Application.................................... Application.............................................. .......... Sign up to vote on this title Creating a Sheet Library.......................................................................................... Creating a Backing Sheet and its Content............................................................... Useful Not useful Creating an Overlay Overlay Sheet and its Content ........................................................ .......................... .................................... ......
6
Symbol Symbol Library Library Administrati Administration on
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Contents
8
Label Library Administration .....................................................................
8.1 8.2 8.3 8.4
Entering Label Library Administration Mode............................................................ Creating a Label Library ....................................................................................... Creating Symbol Templates .................................................................................... Creating Text Templates ......................................................................................
9
Style Library Administration......................................................................
9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9
Creating a Style Library ........................................................................................ Creating and Deleting Styles ................................................................................... Setting Style Attributes ............................................................................................ Creating a Hatching Style Library............................................................................ Creating and Deleting Hatching Styles.................................................................... Setting Hatching Style Attributes ............................................................................. Creating Change Style Libraries.............................................................................. Creating and Deleting Change Styles...................................................................... Setting Change Style Attributes...............................................................................
9.9.1 Setting Change Design Style Attributes ...................................................................... 9.9.2 Setting Change Annotation Style Attributes ................................................................
10
Representation Library Administration ....................................................
10.1 Creating a Representation Library........................................................................... 10.2 Creating Representation Rule Sets .......................................................................... 10.3 Creating and Deleting Representation Rules .......................................................... a Preview 10.4 Associating Representation You're Rules Reading with Styles.......................................................... 10.5 Creating Hatching Rule SetsUnlock ................................................................................... full access with a free trial. 10.6 Creating and Deleting Hatching Rules..................................................................... 10.7 Associating Hatching Rules with Styles................................................................... Download With Free Trial 10.8 Hatching Rule Attributes.........................................................................................1 10.9 Creating Change Rule Sets....................................................................................1 10.10Creating and Deleting Change Rules ..................................................................... 10.11Associating Change Rules with Styles ...................................................................
11
Drawlist Library Administration ................................................................
11.1 11.2 11.3 11.4
Entering Drawlist Library Administration Mode......................................................... Creating a Drawlist Library ...................................................................................... Creating Drawlists.................................................................................................... Sign up to vote on this title Defining Drawlist Members......................................................................................
12
Useful Not useful Tag Rule Library Administration ...............................................................
12.1 Entering Auto Tagging Administration Mode ...........................................................
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Con
13.2.2The SDA Customisation Macros ...............................................................................
13.3 Hangers and Supports ADP ...................................................................................
14
AUTODRAFT Administration ...................................................................
14.1 14.2 14.3 14.4
Accessing AUTODRAFT Administration.................................................................. Starting the Symbol Editor....................................................................................... Starting the Frame Editor......................................................................................... Importing Symbols and Backing/Overlay Sheets......................................................
15
Loading Data Files......................................................................................
15.1 Accessing Load Data Files ......................................................................................
16
Updating the Database...............................................................................
16.1 16.2 16.3 16.4
Updating Picture Files.............................................................................................. Updating Template Instancing................................................................................. Updating Cross-DB Reference Attributes ................................................................. Updating Cross-DB Name Attributes.......................................................................
Appendix A The DRAFT Administrator Menus ......................................................
Appendix B The DRAFT Database Hierarchy .........................................................
Appendix C Libraries Supplied with DRAFT........................................................... Index
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Contents
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
1
About this Guide
1.1
The Scope of this Guide
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
This document is intended for System Administrators responsible fo setting up the Libraries used by the PDMS DRAFT applications.
It is assumed that you are already familiar with using DRAFT to pr annotated drawings, and that you have attended a DRAFT Administration Training course. For information about training cou see AVEVA's worldwide sales and support offices, see the Customer Support pages on our website at http://www.aveva.com/location
For more information about using DRAFT, see the DRAFT online h and the VANTAGE You're PDMS DRAFT User Guide . Reading a Preview
: You must beUnlock a member of the DRAFTADMIN team in ord full access with a free trial. the Administration options on the DRAFT menus. See Secti 2.2. Download With Free Trial
1.2
How the Guide is Organised The remainder of this guide is made up of the following: •
Chapter 2 explains some principles which you need to understan before you try to use the DRAFT Administrator functions.
•
Chapter 3 explains how to control theUseful default settings which aff Not useful the way DRAFT’s applications appear to other users.
•
Chapter 4 tells you how to select the library you wish to work on
Sign up to vote on this title
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
About this Guide
•
Chapter 9 tells you how to configure a Style Library (within the Representation Library), which controls the appearance of various aspects of the drawing (such as which parts of the model are drawn, and which pens are used for which types of line).
•
Chapter 10 explains how to define Representation Rule Sets (within the Representation Library), which reference particular Styles. These can be used to link drawing styles to specific types of element within the Design DB if required.
•
Chapter 11 tells you how to configure a Drawlist Library, which hold ID lists to control which elements are drawn.
•
Chapter 12 explains how to set up the rules for automatic tagging of items in drawings
•
Chapter 13 tells you how to set up defaults for Automatic Drawing Production.
•
Chapter 14 tells you how to edit symbols and sheet frames for use within AUTODRAFT.
•
Chapter 15 tells you how toReading use data files to create new projects. You're a Preview
•
Chapter 16 describesUnlock a special item the full access with on a free trial.Graphics menu which allows you to update parts of the Draft DB explicitly, to correct inconsistencies whichDownload may arise due to Trial operations in other PDMS With Free modules such as reconfiguration.
•
Appendix A shows, in a quick-reference format, the administration parts of the DRAFT menu hierarchy.
•
Appendix B shows that part of the DRAFT (PADD) database hierarchy which is most relevant to the DRAFT administrator, namely the LIBY and its members. The full hierarchy is shown in the VANTAGE PDMS DRAFT User Guide . Sign up to vote on this title
•
Not useful Appendix C shows the Library Hierarchy supplied DRAFT. Useful with
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
Join
2
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Some General Principles
This chapter explains some general principles, which you need to understand before you try to carry out any administrative functions DRAFT. It explains:
2.1
•
Which aspects of DRAFT are under the control of the administr
•
What access rights you must have in the PDMS Project in order able to act as a DRAFT administrator, and how to set these up.
The Role of the DRAFT Administrator
The DRAFT Administrator applications enable you to configure the DRAFT environment to suit specific company and/or project Reading a Preview requirements in theYou're following areas. Default Settings
Unlock full access with a free trial.
The DRAFT defaults system With allows you to define the following: Download Free Trial •
Library pointers
•
Layer settings
•
Sheet sizes
•
Naming conventions
•
User-definable pen settings
•
Name string delimiters
Sign up to vote on this title
Useful
Not useful
The ways in which you set these up are explained in Chapter 4.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Some General Principles
•
ISODRAFT Symbol libraries
•
Label libraries
•
Style libraries
•
Representation rules libraries
•
Drawlist libraries
•
Auto Tagging rule libraries
The ways in which you set these up are explained in Chapters 5 to 12. Automatic Drawing Production
The DRAFT Administration options allow you to set up defaults and define rules that control how drawings are automatically produced and annotated. These functions are explained in Chapter 13. AutoDRAFT Symbols and Sheet Frames
The DRAFT Administration options allow you to edit symbols and sheet frames for use with AutoDRAFT. You can also import symbols and sheet You're Reading a Preview frames from AutoCAD work directories and macros. These functions are explained in Chapter 14 Unlock full access with a free trial. Creating Projects
Download With Free Trial The Settings >Load data file option allows you to create new project areas
using existing data files. This is explained fully in Chapter 15. Database Updating
Occasionally all or part of the DRAFT (PADD) DB may need to be updated to allow for changes made within PDMS but outside the normal DRAFT operations; typically when a project has been reconfigured or the Sign up to vote on this title Design DB has been rebuilt from macros. Updating the DRAFT database Useful Not useful is explained in Chapter 16.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Some General Pr
2.3
Supplied Libraries
The Sample Project supplied with the product contains two Departm and . These Departments contai Libraries that contain sample sheets, symbols, and rulesets for tagg representation etc. The contents of the sample Libraries are summa in Appendix C.
2.4
Searching Libraries
When a DRAFT application user attempts to create a new element, example, a symbolic label, the application searches for relevant Lib in a specific sequence. It looks at each LIBY in the DEPT in the list order until it finds one that contains appropriate type of Library. It adds this LIBY and all subsequent LIBYs to the scrollable list on th Library form until it finds a LIBY which does not contain a relevant LALB. No further searching is carried out. You're Reading a Preview
This principle allows you, as the Administrator, to hide LIBYs from user by adding them to the end with of the members list. (You co Unlock full access a freeDEPT’s trial. alternatively, store all reference LIBYs in a separate DEPT, but thi would add extra DEPTs to the user’s List.) Download With Free Members Trial
It is important to note that, due to this method of searching for the LIBYs, different types of Libraries must be grouped together under same Department if they are all to be available to the user.
2.5
The DRAFT Default Files Sign up to vote on this title
The following is a summary of the default files supplied with the pr Useful Not useful information. The files themselves contain additional The files are st in the PDMSDFLTS directory.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
1
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Some General Principles
DRA-GEN-LINDEF
Macro executed on entry to DRAFT to define line pictures and patterns
DRA-GEN-FONTS
Font names file: four font names can defined
DRA-GEN-TEXT
Sample intelligent texts displayed to user from dynamic text forms
DRA-GEN-CLASHTEMP DRA-GEN-CLASHTEM P
Clash plotting macro template
DRA-GEN-DEFLAY
Layer setup macro: standard default
DRA-GEN-DIMLAY
Layer setup macro: dimension layers
DRA-GEN-HLDLAY
Layer setup macro: H&S layers
DRA-GEN-LABLAY
Layer setup macro: label layers
DRA-GEN-MATLAY
Layer setup macro: matchline layers
DRA-GEN-NLLLAY DRA-GEN-NL LLAY
Layer setup macro: label layers with leader lines
DRA-GEN-NOTLAY
Layer setup macro: note layers
DRA-GEN-PLTEXT
Projection-line Projection-line text options
DRA-GEN-RADLAY
Layer setup macro: radial dimension layers
DRA-GEN-SYMLAY DRA-GEN-SYMLAY
Layer setup macro: symbol layers (2D SYMB)
DRA-GEN-TAGLAY
Layer setup macro: tagging layers (layers with reserved purpose TAG)
ADP Default Files
DRA-GENADP-EQUILOCN
Sign up to vote on this title
General ADP defaults file for equipmen Useful Not useful location plans DRA-GENADP-PIPING
General ADP defaults file for piping
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Some General Pr
DRA-ADP-DIM1LAY
Layer setup macro for ADP Type dimensions
DRA-ADP-DIM2LAY
Layer setup macro for ADP Type dimensions
DRA-ADP-DIM3LAY
Layer setup macro for ADP Type dimensions
DRA-ADP-EQUICLLAY
Layer setup macro for ADP equipm centrelines
DRA-ADP-PESYMBLAY DRA-ADP-PESYMBLAY
Layer setup macro for ADP pipe symbols
DRA-ADP-SCHEDLAY
Layer setup macro for ADP sched
DRA-ADP-SCHEDSUPP
Layer setup macro for ADP Hange Support schedules
DRA-ADP-TAGLAY
Layer setup macro for ADP Taggi
DRA-ADP-DIM3LEFTATTS Dimension setup macro for ADP 3 dimensions LEFT side of view DRA-ADP-DIM3UPATTS DRA-ADP-DIM3UPATT S
Dimension setup macro for ADP 3 dimensions UP side of view
DRA-SDADP-MACRO
Macro file for setting defaults for Steelwork Detailing ADP.
H&S Default Files
DRA-SUPP
Main H&S defaults
DRA-SUPP-HADLAY
Layer setup macro for hanger Sign up to vote on this title dimension layers
DRA-SUPP-HSMLAY DRA-SUPP-HSMLAY
Useful
Not useful
Layer setup macro for hanger mat list layers
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Some General Principles
Detail View Default Files
DRA-LOC-LAYER
Detail layer setup macro for master view
DRA-LOC-NOTE
Default detail view note intelligent text for master view
DRA-LOC-NOTE-EXAMPLES Examples of alternative detail view not intelligent texts for master view DRA-DET-LAYER
Detail layer setup macro for new detail view
DRA-DET-NOTE
Default detail view note intelligent text for new detail view
DRA-DET-NOTE-EXAMPLES Examples of alternative detail view not intelligent texts for new detail view Radial Dimension Default Files
DRA-DIM-PDIM
PDIM setup macro, this macro is executed each time a PDIM is created
DRA-DIM-RDIM
RDIM setup macro, this macro is executed each time a RDIM is created
Miscellaneous Default Files
DRA-AUTONAME DRA-AUTONAME
File required for successful appware loading (for future use)
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
Join
3
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Setting the DRAFT Defaults
This chapter tells you how to define the default settings that will be in the DRAFT applications.
When you enter DRAFT and load the forms and menus interface, th macro %PDMSUI%/DRA/ADMIN/START calls the user-defined set macro %PDMSDFLTS%/DRA-SETUP which, among other actions, to the location of the main DRAFT , DRA-GEN-SYSTEM The environment variable PDMSDFLTS is set to the directory wher defaults file is stored. Remember, if you wish to change the start up operation, that you should only modify DRA-SETUP, not the AVEV defined START or VARS files.
As a DRAFT administrator, you can change the settings in the defa files, if necessary creating a different defaults file for each of the company’s drafting You're requirements. defaults file accessed by an Reading a The Preview individual user is determined by the setting of the user's PDMSDFL Unlock full access with a free trial. environment variable. Defaults can be set for the following: Download With Free Trial •
Definitions of for use with views; defined in terms of thei purpose and associated attribute groups.
•
Definitions of ; that is, the characters used to separate the component parts of an element’s name.
•
Pointers to the from which the different aspects of DRA drawing functions obtain their standard data, for example: Sign up to vote on this title
◊
2D symbols and labels
◊
Backing sheets and overlay sheets
◊
Global representation rules and local styles
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Setting the DRAFT Defaults
3.1
Setting the System Defaults
The DRAFT System Defaults form will be displayed when you select Setting > System Defaults from any of the DRAFT Administration main menus. The File gadget at the top of the body of the form shows the current defaults file.
The Master Project Defaults and Local Project Defaults sections of the form show the default settings of the pointers to the DRAFT Libraries. If you want to change any of these, either type the new element name into the text box, or navigate to the element required and press the appropriate CE button. The text to the right of the CE button shows the type of element required for each Library.
The library reference defaults are also shown on a User Defaults form that is accessed by selecting Options>Defaults from the main application menu. The User Defaults form is initialised with the settings from the Draft Defaults form after the defaults have been loaded from file. Subsequent changes made on the User Defaults Reading a Preview form override (butYou're do not change) the settings on the Draft Default form, allowing a user some flexibility in the use of available Unlock full access with a free trial. libraries during drawing production.
the individual parts of PDMS element name Name delimiters. By default, Download With Free Trial
are separated by a slash delimiting character. For example: SHEETS/SHLB1/BACK1/SN1 This option allows you to specify any other delimiter character which has been used for Style names, Label Library names and Drawlist Library names.
Sign up to vote on this title
The Further Defaults options are as follows: Layer Purpose Definitions
Useful
Not useful
See Section 5.3.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Setting the DRAFT D
3.2
Saving and Loading Default Values Saving Default Files
As supplied, the DRAFT applications reference a defaults file name DRA-GEN-SYSTEM that is set up to reference the AVEVA library database.
When you have modified the defaults forms to suit your own requirements, you can save the updated settings to a file in the usu way; that is, either by updating the current file or by specifying a name. To do so, use the File>Save or File>Save As option, respectivel from the menu on the Draft System Defaults form. Loading Default Files
You can load default settings from a file, which may be either the cu defaults file or a different named file. To do so, use the File>Load File>Load From option, respectively, from the menu on the Draft Defa form.
In each case, you can perform either a load or a load by You're Reading a Preview selecting the relevant option from the submenu. The difference is as Unlock full access with a free trial. follows: •
Full loading of defaults: Download With Free Trial ◊
Clears all existing default values from the forms before load the new ones.
◊
Checks that the minimum number of default values are load allow the application to run correctly. This involves checkin all layer purposes are defined, that naming conventions are specified, and that sheet sizes are set. If any of these setting valu not loaded from the specified file, the standard AVEVA Sign up to vote on this title loaded so that the application can still function.
•
Useful
Not useful
Partial loading of defaults: ◊
Does not clear existing form settings, allowing you to overw
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Setting the DRAFT Defaults
errors at any time, select File > Display Errors from the menu on the Draft System Defaults form. Restoring Defaults from a Backup File
Each time you save an updated defaults file the current defaults settings are saved in a backup file named DRA-GEN-SYSTEM.bak. To reload the previous default settings from the backup file, select File>Restore Backup from the menu on the Draft System Defaults form.
3.3
Setting Layer Purpose Definitions The Layer Purpose Definitions form is displayed when you select the Layer Purpose Definitions button on the Draft System Defaults form. Purpose of layer
Setup/Default filename,
Delete selected
(must be 3 chars)
executed when layer
purpose definition
is created
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Accept current values
Useful
Not useful
Attribute groups determine which attributes are
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Setting the DRAFT D
purpose as a three-character string (the fourth character is added automatically when setting PURP so that multiple layers of a given can be created under a single View).
For example, if you have defined a layer with its purpose defined as and a user decides to have three dimension layers in each View for, steelwork (STLDIM), equipment (EQUDIM) and piping (PIPDIM), the View contents might be as follows: Element Type
Name
PURP
VIEW
XYZ0001/S1/V1
LAYE
XYZ0001/S1/V1/STLDIM
DIMA
LAYE
XYZ0001/S1/V1/EQUDIM
DIMB
LAYE
XYZ0001/S1/V1/PIPDIM
DIMC
n/a
where the fourth character of the PURP (A, B or C) distinguishes th individual DIM layers.
The purpose keyword TAG is reserved for autotagging layer This is a requirement of the application (see Chapter 14) an must alwaysYou're be defined layer defaults. If it is omitted Readingina the Preview TAG layer purpose definition will be appended automaticall Unlock full access with a free trial.TAG layer purpose definit during default initialisation. The cannot be deleted. Download With Free Trial
The Setup File box is used to specify the macro file that will be execu to set the layer attributes after a layer has been created. Default m files are supplied with the product. For example, DRA-GEN-DEFLA defines the default attribute values for layers. This ensures that all create layer annotation to a common standard.
You can copy and modify these macro files to meet your company an project standards. You can also create new files for other purpose ty your own definition. Sign up to vote on this title
Useful Not useful and The Attribute Group buttons (Dim, Note, Text , Lab Symb) allow y specify which attribute types will be displayed on the Layer Attribute form. The combination which applies to each of the currently define
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Setting the DRAFT Defaults
3.4
Layer Creation Definitions The Layer Creation Definitions form is displayed when you select the Layer Creation Definitions button on the Draft System Defaults form. This form allows you to define what layers are created, and how they are named, when a View is created.
Layer name
Purpose
suffix
Select the Purpose from the scrolling list, and change the Purpose and suffix as required. You're Reading a Preview
Note that you can create many layers with the same purpose. Unlock full access with a free trial.
3.5
Download With Free Trial Layer Purpose Filtering
The Layer Purpose Filtering form is displayed when you select the Layer Purpose Filtering button on the Draft System Defaults form. This form defines what Layers are visible in the Layer Note option gadget on the appropriate application menu bar. Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Setting the DRAFT D
Option button shows Layers with PURP set to DIM, ADA, ADB, AD
3.6
Sheet Size Defaults
The Sheet Defaults form is displayed when you select the Sheet Sizes button on the Draft System Defaults form.
This form allows you to define the dimensions and a reference descr for up to 15 standard sheet sizes: You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Setting the DRAFT Defaults
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
3.7
Sign up to vote on this title
Defining Element Naming Conventions Useful Not useful
The Name Convention form is displayed when you select the Naming
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Setting the DRAFT D
Specifies whether or not element is to be named automatically
The form is divided You're into two parts: Reading a Preview •
Mandatory names, that is names for the elements which must Unlock full access with a free trial. named in order for the application to function correctly: DEPT, R DRWG, SHEE and VIEW.With ForFree example, Download Trial drawing numbers typic have a common project related prefix, which you should enter, in Prefix box for the Drawing element.
•
Optional names for the elements which do not need to be named the application to function: VNOT, NOTE, RRUL and VSEC. Fo these elements, use the Named toggle button to specify whether automatic naming is required. Sign up to vote on this title
3.8
Useful Defining Pen Drawing Styles
The
Not useful
form is displayed when you select the
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Setting the DRAFT Defaults
Unused. Reserved for use by DRAFT applications.
In the DRAFT applications, pens 1-120 are selected by colour, style and thickness rather than by number. The user–defined pens 131-170 are identified as pens 1-40 for ease of selection and it is these that we are concerned with here.
Device Plot PlotDevice
Lists available glyphs
Prompts you to pick a pen from the Pens list
You're Reading a Preview Unlock full access with a free trial.
Plus Star Ring Cross Stop
Download With Free Trial
Normal Cross-Hatch Filled Sign up to vote on this title
This form has intelligent settings, so that the parameters useful Useful Not available for selection are those relevant to the particular line style for the current pen.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Setting the DRAFT D
Device Pens and Plot Pens
To identify the pen whose settings you wish to edit, click the Select button and then, when prompted, click on the required pen in the displayed Pens list. (You can position the cursor either on the pen number or on the sample line when picking a pen from the list.) The settings will be updated automatically to show the attribute setting the selected pen. Selecting the Pen to be Defined
You can set any of the standard DRAFT pen attributes for the curre selected pen by using the option buttons that make up the rest of form: Setting the Pen Properties Colour
Sets the pen colour to one selected from a displayed
Type
The first button sets the drawing style to Solid, Dash Double or Chain. The second button sets any relevan subsidiary options. For example, if you select Solid You're Reading a Preview only valid qualifier is Normal; if you select Dash, the Unlock full access a free trial. qualifier may bewith or Long. Normal
Width
Sets the line thickness index in the range 1 to 11. Download With Free Trial Increasing the index by 1 will increase the thickness approximately 0.2 mm.
Glyph
Sets a recurring glyph to one selected from a display list (unless set to None). With no glyph selected, the qualifying selections are invalid. With a glyph select relevant qualifiers may be set using the Line Gap, and Size option buttons. For example: Sign up to vote on this title
Glyph
Useful
Spacing
Not useful Line Gap
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Setting the DRAFT Defaults
The qualifying selections specify the Angle of the lines, the Gap between lines, and whether each hatching line is single or double ( Lines). The specified hatch pattern is used to fill closed primitives (CIRCs, RECTs, etc.).
3.9
Setting Plotting Options
DRAFT allows you to plot files in a variety of formats. As an Administrator you can enter or select operating system command strings that enable users to plot their files in a variety of formats. To select or enter output formats, select Settings>Plotting Options from the main DRAFT Administration menu. The Plotting Options form will appear. You're Reading a Preview
Unlock full access with a free trial.
Download With Free Trial
and This form contains four predefined command Signstrings up to votefor on PostScript this title HPGL format conversion and printing. Useful Not useful
If you wish to use a conversion and printing procedure other than those given, replace the predefined entries by entering the procedure label into
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Setting the DRAFT D
to be performed. This batch file uses the Plot Util Program to perform the plot file conversions and Windows print command to send them to a printe This batch file is run when either of the options are applied. FILE
A plot file is created when a drawing sheet is to b output. When the system command string is to be performed the location of this file plot file replace word ‘FILE’.
postscript
This is the type of conversion from the PDMS plo format to a compatible form the selected plotter. file type for the plotter corresponds to a Plot Utili Program driver name; see the VANTAGE Plot Us Guide for more details.
\\printserver\psprint01
This is the output string and in this example is th Windows network name of the destination printe You're Reading a Preview
Under the WindowsUnlock O/S full it access is possible set the System command st with a freeto trial. direct the plot file directly to the default printer. This is made possi by utilising the AVEVA product “Plot Viewer”. Download Withcalled Free Trial PlotViewer /p FILE
Here, instead of the Plot program, the Plot Viewer program is execu with the following arguments. /p
run Plot Viewer in plot only mode and hence sends the file directly to the default printer.
FILE
this word will be replaced by the plot file name Sign up to vote on this title
Please note that the Plot Viewer program does not print at a true 10 Useful Not useful scale, and therefore your print will be slightly smaller.
An example of the modified form showing the PlotViewer entry is s
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Setting the DRAFT Defaults
Also available under the Windows O/S, it is possible to plot to any printe using the Screen pre-viewer. plotcadc FILE screen -0
Here, the Plot program is executed with the Screen argument. A previewer form is shown which enable you to zoom in and out of the plot file. To send the plot file to a printer, press the button sequence Cntrl-P and the standard Windows print form will be displayed, allowing you to choose any printer as the destination. You're Reading a Preview
For more information on the subject of the Plot executable see the manual VANTAGE PlotUnlock . a free trial. access with Userfull Guide
Once you have set all of the plotting options, select the one you require to Download Trial be set as the default by clicking onWith the Free appropriate radio button in the Active column, then press OK.
The Save>User options pull-down menu will save the settings, which can be recalled by selecting Load>User options. (Pressing OK also saves the settings before closing the form.) Load>Predefined options will load the predefined plotting settings.
3.10 ADP Administration
Sign up to vote on this title
Useful
Not useful
You set the defaults for Automatic Drawing Production from within the
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
4
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Selecting the Working Library
When you enter one of the DRAFT Administration applications, you be prompted to select a working library.
Select Draft>Select Working Library. You will see the Library Selection
The Type button at the top of the form allows you to select the type library you wish to select ( Sheet, Symbol, ISODRAFT Symbol or Labe After you have selected a type, you can scroll through the library lis the Main Library window until you find the main LIBY that holds th library you want to work with.
After you have chosen a Main Library, all the libraries of the select type held in the library will be displayed in the Main Library window the right of the form. You can select the library you want from this window. You're Reading a Preview
Once you have selected your library, any related backing sheets or Unlock access with a free trial. overlays are displayed infullthe bottom window of the form. You can one of these if required. Download With Free Trial
4.1
Changing your Working Library The icons at the top of your DRAFT display tell you: •
The type and name of the library you have currently selected to on, for example: Sign up to vote on this title
•
Useful
Not useful
The library you have currently selected. For example:
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Selecting the Working Library
•
The option gadget on the right allows you to switch the display of elements on and off. For example:
You can add existing Libraries to the list of Working Libraries by selecting Draft > Select Working Library. The Library Selection form will b displayed.
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
5
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Sheet Library Administration
This chapter tells you how to set up Sheet Libraries (SHLB) contain the Backing Sheets (BACK) and Overlay Sheets (OVER) that users reference for use with their drawing sheets. The relevant hierarchy is shown in Appendix B.
The DEPT Project_Libraries, supplied as part of the standa product, contains REGIs named /DRA/PRJ/TMP/ discipline discipline is Piping, Equipment, etc. Each of these REGIs contains DRWGs, which own sample sheets with associated LIBYs. The DEPT Project_Libraries also contains a LIBY named DRA/PRJ/OVERS, which holds sample overlay sheets. You're Reading a Preview
The DEPT Master_Libraries contains a LIBY named Unlock full access with a free trial. DRA/MAS/BACKS, which holds sample backing-sheets. Download With Free Trial
5.1
Entering the Sheet Library Administration Application From one of the DRAFT Administration menus, select Draft>Sheet Libraries. The main menu will change to the DRAFT Sheet Library Administration menu. The menu hierarchy is illustrated in Appendix refer All menu selections specified in the remainder of on this Sign up to vote thischapter title this Sheet Library menu unless otherwise stated. Useful Not useful
Creating
Sheet Library
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Sheet Library Administration
Navigate to the appropriate LIBY level in the existing hierarchy or, if necessary, use Create>Library to add a new LIBY.
Select Create>Sheet Library. It is recommended that you give the new SHLB a name that will make its content obvious to users. The SHLB is effectively a drawing sheet template that aligns with the BACKs and OVERs that it owns, so you must specify its dimensions (either explicitly in the Width and Height boxes, or by selecting a standard sheet size using the option button). This size will be cascaded down to BACK and OVER level.
If you wish to define attributes at SHLB level, such that they will b cascaded down to BACK or OVER level, click on the Attributes button and change the settings on the Sheet Library form. (You can modify these attributes for individual BACKs or OVERs later if you wish.) Standard sheet sizes
Set attributes
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
See section 5.4 Sign up to vote on this title
5.3
Useful
Not useful
Creating a Backing Sheet and its Content
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Sheet Library Admini
Navigate to the appropriate SHLB level.
Select Create>Backing Sheet. It is recommended that you give t new BACK a name that will make its content obvious to users
The BACK is a drawing sheet on which you will position one o more NOTEs, each of which may comprise any combination of primitives, text primitives (TEXP) and existing symbol instanc (SYMB).
You will find it easier to position and align individual NO components (i.e. primitives, text and/or symbol instances) if you display a working with a fairly small spacing (say 10 mm) set the function to on. For each NOTE in turn, select Create>Note>Back .
Depending on the detailed design required, create one or more features of the Backing Sheet Note using the Create>2D Primiti Create>2D Symbol and Create>Text options. As you create each feature, use the cursor to position it and, for a primitive, to def its size. If the grid snap function prevents you setting the prec Reading a Preview position or sizeYou're that you want, either turn snapping off tempor or modify the attributes ofwith thea free primitive later. Unlock full access trial. Restricting the Usable AreaDownload of a Sheet With Free Trial
You can define the usable area of a sheet, so that the area in which user can create views does not overlap any of the backing sheet annotation, by creating a special NOTE with the name backing_sheet_name /LIMITS. This NOTE should contain just a sin RECT primitive that corresponds to the sheet area available to a us When the user selects the option Create>View> Pre-defined Frame , D searches the sheet for this special note and, if found, the VIEW to vote this title defining t dimensions will be set automatically toSign fitupinto theonRECT available area. Useful Not useful
During creation of any Views the limits are used to set the initial po and size of the View, as shown:
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Sheet Library Administration
Limits box Sheet
View
/2
/2
5.4
Creating an Overlay Sheet and its Content You're Reading a Preview
To create and display a new OVER, proceed as follows: Unlock full access with a free trial. Navigate to the appropriate SHLB level.
Select Create>Overlay is recommended that you give the Sheet . It Download With Free Trial new OVER a name to make its content obvious to users. This is important; as each drawing sheet is likely to reference several overlay sheets simultaneously. The function of the Ruleset Referenc button will be explained in Step 4.
In its simplest form, the OVER is a drawing sheet on which you can position NOTEs, for which the procedure is exactly the same as for BACK (see Section 9.3). However, an OVER can also own VIEWs, Sign to vote on thisoftitle (typically used to display keyplan views ofupall or part the Design useful Useful Not DB), each of which can own one or more LAYERs, each of which can in turn, own VNOTEs (View Notes). It is the VIEWs, and their members, which we will consider further (see the hierarchy in
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Sheet Library Admini
at individual VIEW level, or at OVER level (see Step 2), or at S level (Section 5.2).
When you create a VIEW, a set of LAYERs is created automatically, their function and content being determined the default settings, as explained in Section 4.3. (This is exa the same as for the creation of VIEWs during the normal us DRAFT.) To create a VNOTE, navigate to the appropriate LAYER level select Create>Note>Over .
Depending on the detailed design required, create one or more features of the View Note using the Draw options on the main As you create each feature, use the cursor to position it and, fo primitive, to define its size. If the grid–snap function prevents setting the precise position or size that you want, either turn snapping off temporarily or modify the attributes of the primit later. You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
6
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Symbol Library Administration
This chapter tells you how to set up Symbol Libraries (SYLB) conta the Symbol Templates (SYTM) from which users can select 2D sym add to their drawings. Each SYTM may comprise any combination o primitives, text primitives (TEXP) and existing symbol instances (SYMB). The relevant hierarchy is shown in Appendix B.
The DEPT Master_Libraries, supplied as part of the standa product, contains a REGI named DRA/MAS/SYMBOLS, wh holds contains two LIBYs holding general symbols and elect symbols, which you can adapt as required.
6.1
Entering Symbol Library Administration Mode
From one of the DRAFT Administration menus, select Draft>Symbo Libraries. The main menu will change to the DRAFT Symbol Library Administration menu. The menu hierarchy illustrated in Appendix A. menu selections specified in the remainder of this chapter refer to t Symbol Library menu unless otherwise stated.
6.2
Creating a Symbol Library To create a new SYLB, proceed as follows: Sign up to vote on this title
Useful in useful level Navigate to the appropriate LIBY theNotexisting hierarch if necessary, use Create>Library to add a new LIBY.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Symbol Library Administration
change the relevant settings on the resulting form. (You can modify these attributes for individual SYTMs later if you wish.)
Set attributes
Standard sheet sizes
See Section 11.3
6.3
Creating Symbol Templates The SYTMs define the appearance of the 2D symbols which users can select and add to their drawings (as symbol instances ). ).
up the to vote on this title parts of You will find it easier to position and Sign align individual Useful of Not usefulsymbols) if each SYTM (i.e. the primitives, text, and/orinstances other you display a working with a fairly small spacing (say 10 mm) and set the function on.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Symbol Library Admini
it and, for a primitive, to define its size. If the grid–snap funct prevents you setting the precise position or size that you want either turn snapping off temporarily or modify the attributes o primitive later. (Remember, when positioning the component p of the SYTM, where you placed its origin in Step 2.)
6.4
Adding Annotation via a Backing Sheet
When you create each SYTM, you define its origin with respect to it component outlines. It is helpful if users can see where this origin i you may not want to make an origin marker part of the selectable s instance. Similarly, you may wish to add a descriptive name to the SYTM, as displayed on the SYLB sheet, in such a way that the nam not selected for display on the drawing sheet. The solution is to posi the origin marker and descriptive name on a that is displayed with, but does not form part of, the SYLB sheet. To do so, proceed as follows:
Examine the displayed SYLB sheet and make a note of the coordinates of all locations at which you wish to position supplementary supplementary details. (You may be able to use the grid as a measuring scale if you have chosen a convenient spacing spacing and h positioned SYTM components at grid intersection points.)
Change to Sheet Library Administration mode (see Chapter Create a backing sheet (BACK) with the same dimensions as t SYLB sheet and display it in a 2D View.
For each required group of annotations on the SYLB, create a N and position it at the appropriate point on the BACK (using th notes which you made in Step 1 as a reminder); or create all of Sign up to vote on this title annotations within a single NOTE if you prefer.
Useful
Not useful
Change back to Symbol Library Administration mode. Select Modify>Symbol Library>Definition and set the Backing Sheet Ref
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Symbol Library Administration
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
7
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ISODRAFT Symbol Library Administrati This chapter tells you how to set up ISODRAFT Symbol Libraries (ISOLB), containing ISODRAFT Symbol Templates (ISOTM). This you create and modify ISODRAFT Symbol Keys.
7.1
Entering ISODRAFT Symbol Library Administratio Mode From one of the DRAFT Administration Applications main menus, Draft>ISODRAFT Symbol Libraries.
The main menu will change to the ISODRAFT Symbol Library Administr menu. The menu hierarchy is illustrated in Appendix B. All menu selections specified in the Reading remainder of this chapter refer to the You're a Preview ISODRAFT Symbol Library menu unless otherwise stated. Unlock full access with a free trial.
7.2
Download WithSymbol Free Trial Library Creating an ISODRAFT
To create a new ISODRAFT Symbol Library (ISOLB):
Navigate to the appropriate LIBY level in the existing hierarch if necessary, use Create>Library to add a new LIBY.
Select Create>ISODRAFT Symbol Library. It is recommended tha give the new ISOLB a name that will make its content obvious Sign up to vote on this title users.
Useful
Not useful
The ISOLB is a drawing sheet on which you will position the ISOTMs, so you must specify its dimensions (either explicitly i
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ISODRAFT Symbol Library Administration
7.3
Creating ISODRAFT Symbol Templates The ISODRAFT Symbol Templates allow ISODRAFT users to produce user-defined symbols using the DRAFT interface. The symbol definition is made up of two components and . Straights can be solid for normal lines, dashed for insulation lines and chained for tracing lines.
Markers can be defined for symbol arrive and leave points, tee points and spindle points. Create each ISOTM as follows: Select Create>ISODRAFT Symbol Template and give the symbol a name. The Symbol Template Form will be displayed. For more information, see the online help. Define the symbol geometry using the pending on the detailed design required, create one or more components of the ISOTM in Reading a Preview turn from the Draw,You're , and Construct Edit options, which are used in the same way as in Unlock the 2D Drafting Application. full access with a free trial. You can add annotation to an ISODRAFT Symbol Template in the same Download With Free Trial way as for Symbol Templates. Export the ISODRAFT Symbol by selecting Utilities > Export ISODRAFT Symbol. See the online help for more information.
7.4
Importing ISODRAFT Symbols
The Import Isodraft Symbols form is displayed when select Sign up to voteyou on this title Utilities Import Isodraft Symbols from the ISODRAFT Symbol Library useful Useful Not Administration menu. The form allows you to import ISODRAFT symbo macro files into DRAFT symbol libraries.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
Download
News
Documents
Sheet Music
8
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Label Library Administration
This chapter tells you how to set up Label Libraries (LALB) contain the Symbol Templates (SYTM) and Text Templates (TXTM) from w users can create symbolic (SLAB) or general (GLAB) labels, respect Each SYTM may comprise any combination of 2D primitives, text primitives (TEXP) and existing symbol instances (SYMB). Each TX holds specific or intelligent (i.e. #-coded) text in its BTEX attribute. The relevant hierarchy is shown in Appendix B.
The DEPT Master_Libraries, supplied as part of the standa product, contains a REGI named DRA/MAS/LABELS, which holds contains LIBYs holding different types of label templa which you can adapt as required.
8.1
You're Reading a Preview
Entering Label Library Administration Mode Unlock full access with a free trial.
From one of the DRAFT Administration Application main menus, s Download With Free Trial Draft>Label Libraries.
The main menu will change to the Label Library Administration menu, gives you access to the menu hierarchy illustrated in Appendix A.5. menu selections specified in the remainder of this chapter refer to th Label Library menu unless otherwise stated.
8.2
Creating a Label Library
Sign up to vote on this title
Useful
To create a new LALB, proceed as follows:
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Label Library Administration
If you wish to define attributes at LALB level, such that they will b cascaded down to SYTM and TXTM level, click on the Attributes... button and change the relevant settings on the resulting form. (You can modify these attributes for individual SYTMs or TXTMs later if you wish.) Standard sheet sizes
Set attributes
You're Reading a Preview
See Section 9.3
Unlock full access with a free trial.
8.3
Download With Free Trial
Creating Symbol Templates
The SYTMs define the appearance of the 2D symbols that users can refer to when creating SLABs to add to their drawings.
You will find it easier to position and align the individual parts of each SYTM (i.e. the primitives, text, and/or instances of other symbols) if and you display a working with a fairly small spacing (say 10 mm) Sign up to vote on this title set the function on.
Create each SYTM as follows:
Useful
Not useful
Select Create>Symbol Template and give the symbol a meaningful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Label Library Admini
either turn snapping off temporarily or modify the attributes o primitive later. (Remember, when positioning the component p of the SYTM, where you placed its origin in Step 2.) Adding Annotation via a Backing Sheet
When you create each SYTM, you effectively define its origin with to its component outlines. It is helpful if users can see where this or is, but you may not want to make an origin marker part of the selec symbol instance. Similarly, you may wish to add a descriptive name the SYTM, as displayed on the LALB sheet, in such a way that the does not form part of the selectable symbol instance. The solution is position the origin marker and descriptive name on a is displayed with, but does not form part of, the LALB sheet. To do proceed as follows:
Examine the displayed LALB sheet and make a note of the coordinates of all locations at which you wish to position supplementary details. (You may be able to use the grid as a measuring scale if you have chosen a convenient spacing and h positioned SYTM components at grid intersection points.) You're Reading a Preview
Change to Sheet Library mode (see Chapter 5) Unlock full accessAdministration with a free trial. Create a backing sheet (BACK) with the same dimensions as t LALB sheet and displayWith it inFree a 2D View. Download Trial
For each required item of annotation on the LALB, create a NO and position at the appropriate point on the BACK (using the n which you made in Step 1 as a reminder).
Change back to Label Library Administration mode. Select Modify>Label Library>Definition and set the Backing Sheet Refer option to the name of the corresponding BACK that you have j created. Sign up to vote on this title
Useful Not Now, when the LALB is displayed, the foruseful each SYTM w annotation shown for the user’s guidance without confusing the selection of a sy instance for adding to a drawing.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Label Library Administration
Each TXTM automatically includes a Label Frame, although this can be switched off if it is not required.
In order to see the effects of adding individual TXTMs as you build up the LALB contents, open a 2D View window and add the LALB to the display. You may find it easier to position and align TXTMs if you displa a working with a fairly small spacing (say 10 mm) and set the function on; or you may prefer just to position them by eye. Create each TXTM as follows: Select Create>Text Template and give the template a meaningful name.
Use the cursor to position the origin of the TXTM at the required point. (Nothing will appear in the displayed view until you have set the BTEX attribute.) You will be presented with a Modify Text form.
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Enter the required text using the keyboard or insert intelligent text codes, formatting your text using the options above the text box. Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Label Library Admini
covered by the listed options, type its name, preceded by the # character, into the text box. Copying Text from an Existing TXTM
To save unnecessary typing, you can copy text from an existing TXTM into the TXTM that you are currently defining. To do so, ensure that the TXTM that you wish to copy is visible in a 2D V and then click the Insert Text button. When prompted, use the cu to identify the TXTM whose BTEX is to be copied; the text will b inserted after the highlighted line in the Edit Window.
When the required text is displayed in the text box, click Apply copy the string to the BTEX attribute of the TXTM. The text a label frame (if switched on) will appear in the displayed LALB the position you defined in Step 2.
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Label Library Administration
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
9
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Style Library Administration
This chapter tells you how to set up Styles (STYL), which define ho different elements are drawn, and Hatching Styles, which define elements are hatched, and the appearance of the hatching. Styles a hatching Styles are stored in Representation Libraries (RPLB).
This chapter also tells you how to set up Design Change Styles (DCSTYL), which define how different design elements (including hatching) that have changed are drawn, and Annotation Change St (ACSTYL), which define how annotation elements that have change drawn. Design Change Styles and Annotation Change Styles are st in Representation Libraries (RPLB).
From one of the DRAFT Administration application main menus, se Draft > Style Libraries. Reading The main menu willYou're change to thea Preview Representation Style Administration The menu hierarchyUnlock is shown inwith Appendix full access a free trial. A.7.
9.1
Download With Free Trial
Creating a Style Library
are actually (RPLB terms of PDMS Database elements. Note that the STYLs th can reference from an RRUL must be owned by the same To create a new Style Library:
Navigate to an existing LIBY or use Create Sign up to vote>onLibrary this title to add a n LIBY. Useful Not useful
Select Create > Style Library , and you will see the Create RPLB on which you can give the Style Library a name. It is recomme
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Style Library Administration
STYLs in the current Style Library. This part of the form is explained in Section 9.2. •
9.2
The lower part of the form allows you to set attribute values for the current STYL; that is, for the STYL which is highlighted in the list. This part of the form is explained in Section 9.3.
Creating and Deleting Styles
The upper part of the Style Library form shows the name of the current RPLB that is being used as a Style Library, and a list of all STYLs withi it (or None if you have just created the RPLB). Current Style Library
You're Reading a Preview Name Gen Pipe Steel
Unlock full access with a free trial.
Download With Free Trial
List of STYLs in the Current Style Library
Creating a Style
To create a new STYL, click the Create Style button and give the new STYL a name. The name will be added to the displayed list and will be Sign up to vote on this title STYL will highlighted as the current selection. The attributes of the new have the default settings shown by the gadgets in the part of the Not useful Useful lower form. Change these, if required, as explained in Section 9.3.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Style Library Admini
Gen shows the STYL name, the drawing level, and any pen and
settings applicable to general drawings.
Pipe shows the STYL name, the drawing level, and any pen and
settings applicable to pipework drawings.
Steel shows the STYL name, the drawing level, and any pen and
settings applicable to structural steelwork drawings.
Set an appropriate Display mode to make it easier to find the STYL whose attributes you want to modify, without having to recognise it name.
9.3
Setting Style Attributes
The lower part of the Style Library form consists of three sets of gadg that allow you to modify the attribute settings for the currently highlighted STYL.
To modify any of the attribute settings for the current STYL, chang You're Reading a Preview settings of the corresponding gadgets (as explained in the following paragraphs) and click the Apply button. Unlock full access with a free trial. Pen On or Off
Drawing level Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Pen num (1-40)
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Style Library Administration
: Every primitive in the design model has an associated drawing level range attribute. If the drawing level given here lies within this range, the 3D object will be drawn when it is added to the Draw List. Assigning Pens
The Pens section of the form shows the assignment of each pen type: For each type of pen, you can assign either a , defined in terms of its colour, line width and line style, or a . See Section 3.8 for more information about user-defined pens. If you have chosen a , set the colour, line width and line style using the corresponding option buttons.
If you have chosen a pen, enter the pen number in the appropriate text box. Alternatively, click the Reselect button to display a Select User–Defined Pen form that shows all current pen definitions. Use the Cursor Select function to pick the required pen from the display and then click OK to copy the selected pen number to the Style Library form.
You're Reading Preview All pen types except the Frontface Penahave a toggle button immediately following the pen name on the form. Set this On or Off to specify whethe Unlock full access with a free trial. or not that pen type is to be used in the current Style. Download With Free Trial
Setting Drawing Flags On or Off
The Representation Flags section of the form shows the current On/Off settings for the TUBE, PSYM, OBST, INSU, PRFG and PLFG flags: •
If switched off this will suppress the display of all pipes. If switched off this will suppress the display of all
•
piping symbols.
Sign up to vote this titleof all If switched off this will suppress the on display
•
obstructions. •
Useful
Not useful
If switched off this will suppress the display of any
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Style Library Admini
9.4
Creating a Hatching Style Library
are actually (RPLB) in terms of PDMS Database elements. Note that the HSTYLs that you can reference from a HRUL must be owne the same LIBY. To create a new Hatching Style Library:
Navigate to an existing LIBY or use Create > Library to add a n LIBY.
Select Create > Hatching Library, and you will see the Create RP form on which you can give the Hatching Style Library a name recommended that you give the new RPLB a name that makes obvious that it is a Hatching Style Library.
When you press OK on the Create RPLB form, you will see the Hatchin Styles form that allows you to define the HSTYLs to be stored in the library. The Hatching Styles form be considered You'rewill Reading a Preview in two stages:
9.5
•
The upper part of thefullform Unlock accessallows with a freeyou trial. to create and delete HSTY contains a list of all HSTYLs in the current RPLB. This part of t form is explained in Section Download With9.5. Free Trial
•
The lower part of the form allows you to set attribute values for current HSTYL; that is, for the HSTYL which is highlighted in t list. This part of the form is explained in Section 9.6.
Creating and Deleting Hatching Styles Sign up to vote on this title
The name of the current RPLB is shown at the top of the form. You Useful Not useful change the current element by selecting the Library you want in th Members List and pressing CE.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Style Library Administration
Current Hatching Library
List of HSTYLs in the Current Style Library
Creating a Hatching Style
To create a new HSTYL, click the Create Style button and give the new HSTYL a name. The name will be added to the Hatching Styles list and will be highlighted as the current selection. The attributes of the new HSTYL will have the default in the lowe r part of the You'resettings Reading shown a Preview form. Change these, if required, as explained in Section 9.6. Unlock full access with a free trial.
Deleting a Hatching Style
Download With Free Trial
To delete a HSTYL from the current library, highlight it in the list and click the Delete Style button.
9.6
Setting Hatching Style Attributes There are three sets of gadgets in the lower part of the form which allow you to modify the attribute settings for the currently HSTYL. Sign up to vote on this title Set the standard pen and pattern
Useful
Not useful Press Reselect to pick a pen graphically
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Style Library Admini
This includes an HVAC duct symbol
Type in the pen number
or
Press Reselect to pick a pen graphically
Hatching Pattern
The choices are Standard or User defined. If a standard pattern is re you can choose from a list of standard pen colours, hatch spacing an angles. If a user-defined pattern is required then there are up to 40 available. Outline Pen
The choices are Standard , User Defined or None. If a standard pen is required you can choose from a list of standard pen colours, thickne and styles (Solid, Dashed etc). There are 40 User definable pens. If outline pen is used then each surface hatched will be outlined in the given pen. Pipe Symbols
You're Reading a Preview
The choices are ON or OFF. Choosing ON will hatch the cross-sectio access with a free trial. pipe or HVAC duct Unlock with full a piping end symbol or ducting end symbol will hatch the full cross-section of the pipe or duct. Download With Free Trial
9.7
Creating Change Style Libraries To create a new Change Design Library:
Navigate to an existing LIBY or use Create > Change Design Lib Sign up to vote on this title to add a new LIBY.
Useful
Not useful
Select Create > Change Design Library, and you will see the Crea RPLB form on which you can give the Change Design Library a
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Style Library Administration
The Change Design Library form and the Change Annotation Library form are similar, having identical upper parts, but different lower parts.
9.8
•
The upper part of these forms is explained in Section 9.8.
•
The lower part of the Change Design Library form allows you to set attribute values for the current DCSTYL; that is, for the DCSTYL that is highlighted in the list. This part of this form is explained in Section 9.9.1.
•
The lower part of the Change Annotation Library form allows you to set attribute values for the current ACSTYL; that is, for the ACSTYL that is highlighted in the list. This part of this form is explained in Section 9.9.2.
Creating and Deleting Change Styles The upper part of the Change Design Library and Change Annotation Library forms shows the name of the current RPLB that is being used as a Change Style Library, and a list of all aStyles (either DCSTYLs or You're Reading Preview ACSTYLs) within it (or None if you have just created the RPLB). Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Style Library Admini
list and will be highlighted as the current selection. The attributes o new DCSTYL will have the default settings shown by the gadgets in lower part of the form. Change these, if required, as explained in Se 9.9.1 for DCSTYLs or Section 9.9.2 for ACSTYLs. Deleting a Change Style
To delete a DCSTYL (or ACSTYL) from the current library, highligh in the list and click the Delete Style button. Listing Some of the Attributes
The amount of information about each DCSTYL (or ACSTYL) show the list is controlled by the Display mode options: Name shows only the DCSTYL name.
Gen shows the DCSTYL name, the drawing level, and any pen a
flag settings applicable to general drawings.
Pipe shows the DCSTYL name, the drawing level, and any pen a
flag settings applicable to pipework drawings. You're Reading a Preview Steel shows the DCSTYL name, the drawing level, and any pen
flag settings applicable to structural steelwork drawings. Unlock full access with a free trial.
Set an appropriate Display mode to make it easier to find the DCST Download Free Trial whose attributes you want toWith modify, without having to recognise it name.
9.9
Setting Change Style Attributes
This Section describes the use of the lower parts of the Change Desig se Library and Change Annotation Library forms to modify the attribute Sign up to vote on this title for the currently highlighted DCSTYL or ACSTYL.
9.9.1
Useful
Not useful
Setting Change Design Style Attributes
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Style Library Administration
The Pens section of the form shows the assignment of each pen type, six of which are equivalent to the six pens of a Representation Style (STYL), and two of which are equivalent to the two pens of a Hatching Style (HSTYL). You're Reading a Preview
For each type of pen, you can assign either a pen, defined in Unlock full access with a free trial. terms of its colour, line width and line style, or a pen. See Section 3.8 for more information about user-defined pens. Download With Free Trial If you have chosen a pen, set the colour, line width and line style using the corresponding option buttons.
If you have chosen a pen, enter the pen number in the appropriate text box. Alternatively, click the Reselect button to display the Select User-Defined Pen form to show all current pen definitions. Use the Cursor Select function to pick the required pen from the display and then click OK to copy the selected pen number to the Change Design Librar form. Sign up to vote on this title For the Hatching Pattern pen, the choices areUseful Notoruseful If a standard pattern is required you can choose from a list of standard pen colours, hatch spacing and angles. If a user-defined pattern is
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Style Library Admini
9.9.2
Setting Change Annotation Style Attributes
The lower part of the Change Annotation Library form consists of sets o gadgets that allow you to modify the attribute settings for three asp of changed annotation elements: linear graphics, hatched areas, and for the currently highlighted ACSTYL.
To modify any of the attribute settings for the current ACSTYL, cha the settings of the corresponding gadgets (as explained in the follow paragraphs) and click the Apply button.
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Assigning Pens
The Pens section of the form shows the assignment of pens to each o aspects of changed annotation elements: Annotation Linear Graphics
For the Note Line pen, the choices are or Sign up to vote on this title have chosen a pen, set the colour, line width and line styl Useful Not useful using the corresponding option buttons. If you have chosen a
pen, enter the pen number in the
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
1
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Style Library Administration Administration
standard pen colours, hatch spacing and angles. If you have chosen a pattern there are up to 40 styles available. The Note Line Pen and Hatch Pattern pen types have an toggle button immediately immediately following the pen name on the form. If you select this option then the style of the pen will not be changed and the STYL or HSTYL defined for that pen will be used. Annotation Text
For the text of a changed annotation element there are separate gadgets that allow you to specify the text colour and the text font: Text Pen allows you to select from a list of standard text colours. Font allows you to select from a list of standard text fonts.
The Representation Flags section of the form contains gadgets for further defining how changed text is represented: represented: •
•
The Underline toggle button allows you to underline all changed annotation text.
Brackets allow you to enclose changed annotation text in brackets. You can select select the bracket bracket type from a list of standard standard bracket bracket types.
All pen types types (including Font) have a toggle toggle button immediately immediately in front of the pen name on the form. Set this On or OFF to specify whether or not that pen type is to be used in the current ACSTYL.
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
10
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Administration This chapter tells you how to set up: •
Representation Representation Rule Sets (RRST) and Representation Representation Rules (RR These define the appearance of the drawing of the Design Mode
•
Hatching Rule Sets (HRST) and Hatching Rules (HRUL). These define how model faces created by section planes, and surfaces o Specified Design primitives, are hatched.
These Rules Sets are created within Representation Representation Libraries (RPL When accessed during normal DRAFT drawing operations, each RR references a STYL or HSTYL (Hatching Style) that is to be applied View from which the owning RRST has been called.
: The DEPT Project_Libraries, Project_Libraries, supplied as part part of the the standa product, contains contains a LIBY named DRA/PRJ/REPR, which ho sample representation rule libraries. This chapter also tells you how to set up: •
Change Rule Sets (CRST), Design Change Rules (DCRULE) and Annotation Change Rules (ACRULE). (ACRULE). These define define the appeara appeara changed design elements and changed annotations on the drawi the Design Model.
Change Rule Sets are created within Representation Representation Libraries (RPL When accessed during normal DRAFT drawing operations, each DCRULE references a DCSTYL and each ACRULE references an ACSTYL, which which is to be applied applied to the View from which the owning owning Sign up to vote on this title CRST has been called.
Useful
Not useful
From one of the DRAFT Administration application main menus, se Draft > Representation Rules. The main menu will change to the
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Administration
Navigate to an existing LIBY or use Create > Library to add a new LIBY. Select Create > Representation Library or Create > Hatching Library. You should give the new RPLB a name to make it obvious obvious whether it is a Representation Representation Rule Library or a Hatching Library. : The STYLs STYLs or HSTYLs which you can reference reference from a RRUL or an HRUL must be owned by the same LIBY. Local Rules
Views can also own HRULs and RRULs. The View HRSF attribute should be set to point to a HRST, and the HSTYF attribute of the HRUL owned by the View should be set to point to HSTYLs, in the same way HRULs owned directly by HRST The database hierarchy is shown in the following diagram. User Def i ned
Admi ni s t r at or Def i n ed
LIBY
VIEW
RRUL
H R S F
HRUL
RPLB
RPLB
RPLB
Hatching Library
Representation Rep resentation Library Library
Style Library
HRST
HRUL
HRST
HRUL
RRST
RRUL
RRST
STYL
STYL
RRUL Sign up to vote on this title H S T Y F
Useful
HSTYL
Not useful
H S T
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Admini
Change Library
To create a new RPLB, proceed as follows:
Navigate to an existing LIBY or use Create > Library to add a n LIBY.
Select Create > Change Library. You should give the new RPLB name to make it obvious that it is a Change Rule Library. Local Rules
Unlike Representation Rules, Views cannot own DCRULEs or ACR All Change Rules applicable to a View are owned by a Change Rule (CRST) which is referenced by the View's Change Ruleset Reference attribute. The database hierarchy is shown in the following diagram.
RPLB
RPLB
You're Reading a Preview Unlock full access with a free trial.
VIEW
CRSF
CRST
DCSTYL
ACSTY
Download With Free Trial
DCSTYF ACRULE
DCRULE
ACSTYF
Sign up to vote on this title
Useful Not Change useful Change Rule Setsand Styles
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1
1.8K views
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
1
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Administration
(Remember that each RRUL can only reference a STYL in the same LIBY). The Representation Rule Set form will be considered in two stages: •
The upper part of the form is concerned with the creation and deletion of RRULs within a RRST. It also allows you to restrict the application of a RRUL to a s pecif ied class of elements. This part of form is explained in Section 10.3.
•
The lower part of the form displays a list of all currently defined STYLs and allows you to select any one of these to be referenced by the current RRUL. This part of the form is explained in Section 10.4
10.3 Creating and Deleting Representation Rules The upper part of the Representation Rules form shows the name of the current RPLB. You can switch to another RPLB by selecting it in the Members List and pressing the CE button. You're Reading Preview CurrentaRepresentation Library Unlock full access with a free trial. Selected Rule Set
Download With Free Trial
Design element type to which RRUL applies
Sign up to vote on this title
Named elements to which RRUL applies
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Admini
Specifying the Owning Rule Set
Select the RRST whose member RRULs you wish to modify from th Set drop-down list. The RRULs owned by the current RRST will be in the Rule list (or None if you have just created the RRST). Creating a Rule
To create a new RRUL, click the Create button and give the new RR name. The name will be added to the list and will be highlighted as current selection. Deleting a Rule
To delete a RRUL from the current RRST, highlight it in the Rules and click the Delete button. Specifying the Elements to which Rules Apply
You can specify the type of element or a list of named elements, as follows:
To specify the of element to which the current RRUL is to be You're Reading a Preview applied, click the For radio button and select the type from the drop Unlock full access with a free trial. list.
To specify named elements to which the current RRUL is to be appl Download With Free Trial press the Modify button, and the Names form will be displayed. On t form, select individual elements from the Members list for copying t Names list in the usual way. When you press OK, the names will be shown in the text pane on the Representation Rules form. Criteria for Rule Application
To apply qualifying restrictions to the elements specified by the For if the option, type an expression in the With Sign textupbox. For example, to vote on this title gadget specifies Branches, you might useUseful the With qualifier to enter useful Not ‘(HBOR GT 100) AND (TBOR GT 80)’ meaning ‘Branches with HBOR greater than 100 mm and TBOR gr
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
1
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Administration
10.4 Associating Representation Rules with Styles The lower part of the Representation Rule Set form allows you to list the contents of any Style Library in the same LIBY as the current Representation Library. Select Style Library
Name Gen Pipe Steel
List of STYLs in the
You're Reading a Preview current STYL
Unlock full access with a free trial. To associate a RRUL with a STYL, proceed as follows:
Use the Style LibraryDownload option button to select With Free Trial the RPLB that holds the required STYL. All STYLs in the selected Style Library will be shown in the list.
If necessary, use the Display option button to change the amount of information shown in the list. The display options are identical to those that you used when you created the Style Library, as described in Section 9.1. Ensure that the required RRUL is highlighted in on the Sign up to vote thisRule title list and select the corresponding STYL from the Style list; then click the useful Useful Not Apply button to create the association.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
1
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Admini
reference from each of these to an existing HSTYL. (Remember tha HRUL can only reference an HSTYL in the same LIBY). The Hatching Rule Set form will be considered in two stages: •
The upper part of the form is concerned with the creation and deletion of HRULs within a HRST. It also allows you to restrict application of a HRUL to a specified class of elements. This part the form is explained in Section 10.6.
•
The lower part of the form displays a list of all currently defined HSTYLs and allows you to select any one of these to be referenc the current HRUL. This part of the form is explained in Section
10.6 Creating and Deleting Hatching Rules
The upper part of the Hatching Rules form shows the name of the cur RPLB. You can switch to another RPLB by selecting it in the Memb List and pressing the CE button.
You're Reading a Preview The Rules Sets drop-down list allows you to switch to any HRST ow by the current RPLB. Unlock full access with a free trial.
The Rules list shows all HRULs in the current HRST. Download With Free Trial Current Representation Library
Selected Rule Set
Design element type to which HRUL applie
Sign up to vote on this title
Useful
Named elements to which HRUL applies
Not useful
PML expression defining criteria
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Administration
Creating a Rule
To create a new HRUL, click the Create button and give the new HRUL a name. The name will be added to the list and will be highlighted as the current selection. Deleting a Rule
To delete an HRUL from the current HRST, highlight it in the Rules Lis and click the Delete button. Specifying the Elements to which Rules Apply
You can specify the type of element or a list of named elements, as follows: To specify the of element to which the current HRUL is to be applied, select the For radio button and select the type from the dropdown list.
To specify named elements to which the current HRUL is to be applied, press the Modify button, and the Names form will be displayed. On this form, select individual elements from the Members list for copying to the You're Reading a Preview Names list in the usual way. When you press OK, the names will be Unlock full access with a free trial. shown in the text pane on the Hatching Rules form. Criteria for Rule Application
Download With Free Trial
To apply qualifying restrictions to the elements specified by the For option, type an expression in the With text box. For example, if the For gadget specifies Branches, you might use the With qualifier to enter ‘(HBOR GT 100) AND (TBOR GT 80)’ meaning ‘Branches with HBOR greater than 100 mm and TBOR greater than 80 mm’.
Signthe up to vote onof this titleHSTYL (if The Style line, halfway down the form, shows name the set) that is referenced by the current HRUL. Usefulway Notwhich useful you set The in this is explained in Section 10.7.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Admini
10.7 Associating Hatching Rules with Styles
The lower part of the Hatching Representation Rules form allows you t the contents of any Style Library in the same LIBY as the current Hatching Library. Select Style Library
List of HSTYLs in the
The Style looks like this
Allows you to set which faces are hatched
You're Reading a Preview
The Style gadget displays the current Hatching Style of the selected Unlock full access with a free trial. Hatching Rule. To associate an HRUL with an HSTYL:
Download With Free Trial
Select the RPLB owning the required HSTYL from the Styles down list. All HSTYLs in the selected Hatching Library will be shown in the Display list.
: In the Administration application, this is all the Hatching Libraries in the MDB, but for the user defined local hatchin only the library from the User Defaults Local Styles is avail
Ensure that the required HRUL is highlighted intitle the Rules Sign up to vote on this Styles select the corresponding HSTYL from the list; then click Useful Not useful Apply button to create the association.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Administration
10.8 Hatching Rule Attributes The Hatching Rule attributes give you more control over which surfaces of an element are hatched. The Hatching Rules Attributes form is displayed when you press the Attributes button on the Hatching Representation Rules form.
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
•
Rule Pressing the Plot button on the HatchingSign form upAttributes to vote on this title will display the Hatching Rule Attributes Pot form (shown Not useful which Useful overleaf), illustrates the Hatching Rule Attributes.
Hatching rules can Consider:
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Admini
Only Surfaces Perpendicular to the View Direction – example, if th
direction is north then the south face of the element will be hatc assuming it meets the initial criteria.
Only Surfaces Facing in a Specified Direction means that the user
specify a direction normal to the surface to be hatched, instead o using the view direction. An example of this is a box shown in a isometric view with the top surface cross-hatched. If six surface box were required to have different hatching styles then this op would be used on six Hatching Rules.
The Direction and Derived gadgets are active when Only Surfaces Fa a Specified Direction is chosen. If you press Derived, you will be prom to pick a Design element.
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Administration
10.9 Creating Change Rule Sets When a Change Library is created, a Change Rule Set (CRST) is not automatically created. To create a CRST below a Change Library, navigate to the RPLB, select Create > Change Ruleset. The Create CRST form will be displayed, and you can give the CRST a name.
When you click OK on the Create CRST form, you will see the Change Representation Rules form to allow you to define individual DCRULEs and ACRULEs and to make references from these to existing DCSTYLs and ACSTYLs. The Change Representation Rules form will be considered in two stages: •
The upper part of the form is concerned with the creation and deletion of DCRULEs and ACRULEs within a CRST. If creating a DCRULE it allows you to restrict the application of a DCRULE to a specified changed element. If creating an ACRULE it allows you to restrict the application of an ACRULE to a specified changed annotation type. This part of the form is explained in Section 10.10.
•
The lower part of the form displays a list of all currently defined Unlock full access withon a free trial. DCSTYLs or ACSTYLs, depending the selection made in the uppe part of the form, and allows you to select any one of these to be referenced by the current DCRULE or ACRULE. This part of the Download With Free Trial form is explained in Section 10.11.
You're Reading a Preview
10.10 Creating and Deleting Change Rules
The upper part of the Change Representation Rules form shows the name o the current RPLB. You can switch to another RPLB by selecting itin the Members List and clicking the CE button. Sign up to vote on this title
Current Change Library
Useful
Not useful
Selected Change Rule Set
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Admini
Desi Anno Element type to which Change Rule applies
Change Style referenced by Change Rule PML expression defining criteria
Named elements to whic Change Rule applies
You're list Reading a Preview The Rule Sets drop-down allows you to switch to any CRST own the current RPLB. Unlock full access with a free trial.
The Rules list shows all DCRULEs and ACRULEs in the current CR Download With Free Trial
Specifying the Owning Rule Set
Select the CRST whose member DCRULEs or ACRULEs you wish modify from the Rule Sets drop-down list. The DCRULEs and ACRU owned by the current CRST will be shown in the Rules list (or None have just created the CRST). Creating a Rule Sign up to vote on this title
To create a new Rule, first select the type of Change Rule that you w Useful(ACRULE), Not useful to create, Design (DCRULE) or Annotation from the drop-down list, then click the Create button and give the new Rule a name. The name will be added to the list and will be highligh
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Administration
To specify the of changed element to which the current DCRULE or ACRULE is to be applied, select the type from the For drop-down list. Use the right-hand drop-down list for Annotation Changes and the left-hand drop-down list for Design Changes. The drop-down list available depends on the type of Change Rule selected.
To create a list of changed design elements that a DCRULE is to be applied to, select an option in the For drop-down list, then click the Add button. Select another option from the For drop-down list and again click the Add button. Clicking the Add button adds the option selected to the list. Individual options can be deleted from the list by selecting them and clicking the Remove button. A complete options list can be deleted by clicking the Clear button. Criteria for Rule Application
To apply qualifying restrictions to the elements specified by the For option, type an expression in the With text box. For example, if the For gadget specifies Branches, you might use the With qualifier to enter ‘(HBOR GT 100) AND (TBOR GT 80)’ meaning ‘Branches with You're HBORReading greater than 100 mm and TBOR greater a Preview than 80 mm’. Unlock full access with a free trial.
The Style line below the With text box shows the name of the Change Style which is referencedDownload by the current Change With Free Trial Rule. The way in which you set this is explained in Section 10.11.
10.11 Associating Change Rules with Styles The lower part of the Change Representation Rules form allows you to list the contents of any Change Style Library in the same LIBY as the current Change Style Library. Sign up to vote on this title
Useful
Select Change Style Not useful Library
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Admini
List of Change Styles in the current Change Style
The Style gadget displays the current Change Style of the selected Change Rule. To associate a Change Rule with a Change Style:
Select the RPLB owning the required Change Style from the Styles drop-down list. All Change Styles of the relevant type in the selecte RPLB will be shown in the Display list.
Ensure that the required Change Rule is highlighted in the Rules select the corresponding Change Style from the Styles list, then clic Apply button to create the association.
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Representation Library Administration
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
11
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Drawlist Library Administration
This chapter tells you how to set up Drawlist Libraries (DLLB), eac containing a group of Drawlists (IDLI; also known as ID Lists) whic allow users to create lists of design elements to be drawn or section You can allocate DLLBs and IDLIs to design items according to des disciples, project areas, or any other classifications appropriate to y company’s working practices.
Each IDLI comprises a list of Design elements, in the usual format Add List and a Remove List, which can all be displayed in an area v simply by reference to the IDLI name.
The DEPT , supplied as part of the standa product, contains a LIBY named DRA/PRJ/DRAWLISTS, w holds sample drawlist libraries. You're Reading a Preview
11.1 Entering Drawlist Library Administration Mode Unlock full access with a free trial.
Download With Free Trialmenus, select Draft>Drawlis From one of the DRAFT Administration Libraries. The main menu will change to the DRAFT Drawlist Library Administration menu. The menu hierarchy is illustrated in Appendix All menu selections specified in the remainder of this chapter refe Drawlist Library menu unless otherwise stated.
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Drawlist Library Administration
11.2 Creating a Drawlist Library To create a new DLLB, proceed as follows:
Navigate to the appropriate LIBY level in the existing hierarchy or, if necessary, use Create>Library to add a new LIBY.
Select Create>Drawlist Library. It is recommended that you give the new DLLB a name to make its use as a Drawlist Library obvious to users and indicate the IDLI classifications that it is to contain.
11.3 Creating Drawlists To create the first IDLI in a new DLLB, select Create>Drawlist and give the new IDLI a meaningful name. To add another Drawlist to a DLLB that already has member IDLIs, select Modify>Drawlist Library. (You can, of course, do this even if the DLLB is empty, as an alternative to the method given in the preceding You're Reading a Preview paragraph.)
full access with with a free trial. In either case, you will beUnlock presented a Drawlist Management form. This form is the same as that used to define local Drawlists. For more Download Withonly Freedifference Trial information, see the online help. The is that as DRAFT Administrator you are creating Drawlists at Library level rather than at local user level. Only the basic principles of using the form will be repeated here, as a reminder.
The Drawlist Management form will be considered in two stages: •
•
The upper part of the form is concerned with the creation and deletion of IDLI elements within a DLLB. This part of the form is explained in the remainder of this section. Sign up to vote on this title Useful Not useful select The lower part of the form allows you to elements from the Design DB for inclusion in the Add and Remove lists (ADDE and REME) of a specified IDLI. This part of the form is explained in
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Drawlist Library Admini
The upper part of the Drawlist Management form appears like this: Current Drawlist Library
List of IDLIs in Current DLLB
Create and delete IDLIs in Current DLLB
Selecting a Drawlist Library
To specify the Drawlist Library whose member IDLIs you wish to m use the Drawlist Library option button. The list that is presented to y You're a Preview includes both DLLBs you Reading have defined and standard DLLBs that w supplied as part of the product (as determined by the Drawlists Lib Unlock full access with a free trial. Reference on the Draft Defaults form; see Section 3.1). Creating a Drawlist
Download With Free Trial
To create a new (empty) IDLI, click the Create button and give the I name. Creating a Copy of an Existing Drawlist
To create a new IDLI that has the same Add and Remove lists as existing IDLI, click the Create Copy button, give the new IDLI a nam and use the displayed Copy Drawlist form to toselect Sign up vote onthe this IDLI title to be co Deleting a Drawlist
Useful
Not useful
To delete an IDLI from the current DLLB, highlight it in the displa
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Drawlist Library Administration
11.4 Defining Drawlist Members The lower part of the Drawlist Management form contains the gadgets that you use to build up the Add and Remove lists owned by each Drawlist.
List of Design elements or List of Drawlists
List of elements in Add List and Remove List
You're Reading a Preview Unlock full access with a free trial.
Design Members Drawlists
Element selection Download With Free Trial gadgets
The usual principles apply; that is, you select items from the Reference List Members list and copy them into the Drawlist Members list by using the Add, Remove or Volume Defined buttons.
The Drawlist Members list shows all elements in both the Add List and th Remove list, the element names being qualified by ‘Add’ or ‘Remove’ to Sign up to vote on this title show their status. Identifying Design Elements
Useful
Not useful
The Reference List Members list can show either the Design DB elements
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Drawlist Library Admini
limits box is currently defined, you will be presented with a Drawlis Limits form on which you can enter coordinates of two opposing corn the required volume. Deleting an Entry from the Drawlist Members List
To delete an entry from the Drawlist, highlight the relevant line in Drawlist Members list and click the Delete Entry button. The selected may be either an Add entry or a Remove entry.
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Drawlist Library Administration
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
12
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Tag Rule Library Administration
This chapter explains how you set up Tag Rule Sets (TRST) and Ta Rules (TAGR), within Tag Rule Libraries (TRLB). When accessed d normal DRAFT drawing operations, each TAGR references a Taggi Template (which may be either a SYTM or a TXTM; see Chapter 8). rules determine which items will be tagged in the View graphics.
The DEPT , supplied as part of the standa product, contains a LIBY named DRA/PRJ/AUTOTAG, whi holds sample tag rule libraries for various disciplines.
12.1 Entering Auto Tagging Administration Mode
From one of the DRAFT Administration menus, select Draft>Taggin You're Reading a Preview Rules. The main menu will change to the DRAFT Tagging Rules The full menu Administration menu.Unlock accesshierarchy with a free trial.illustrated in Appendix A. menu selections specified in the remainder of this chapter refer to t Auto Tagging menuDownload unless otherwise stated. With Free Trial
12.2 Creating a Tag Rule Library To create a new TRLB, proceed as follows:
Navigate to the appropriate LIBY level in the existing hierarch if necessary, use Create>Library to add a new LIBY. Sign up to vote on this title
Select Create>Tagrule Library. It is that you give Useful Not useful recommended new TRLB a name to make its use as a Tag Rule Library obvio users.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Tag Rule Library Administration
to the templates which control the format of the associated tags. This part of the form is explained in Section 13.4.
12.3 Creating and Deleting Tag Rule Sets
The upper part of the Tagging Library form shows the name of the current LIBY and has an option button which allows you to switch to any TRLB owned by that LIBY. It also incorporates a list of TRSTs within the current TRLB. Current Library
Selected TRLB
List of TRSTs in You're Reading a Preview selected TRLB Unlock full access with a free trial.
Download With Free Trial
Specifying the Owning Tag Rule Library
To specify the TRLB whose member TRSTs you wish to modify, use the Tag Rules Library option button to select from those available in the current LIBY. The TRSTs owned by the current TRLB will be shown in the Tag Ruleset list (or None if you have just created the TRLB). Creating a Tag Rule Set
Sign up to vote on this title
Not useful To create a new TRST, click the Create Ruleset button give the new Useful and TRST a name. The name will be added to the displayed list and will be highlighted as the current selection.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Tag Rule Library Admini
12.4 Creating and Setting Up Tag Rules
The lower part of the Tagging Library form contains all of the gadgets necessary to create TAGRs, to define the types of element to which are to be applied, and to set references to the templates which contr format of the associated tags. Current TAGR
Design element class to which TAGR applies
PDMS expressio
Associated label template You're Reading a Preview
Viewing Tag Rules
Unlock full access with a free trial.
Download WithaFree The Rule option button displays list Trial of all TAGRs in the current T (i.e. the TRST highlighted in the Tag Ruleset list). It is also used to change the current TAGR if you wish to modify its attribute setting
Creating a Tag Rule
Tag Rules are always named automatically when they are created. You cannot change the name.
Sign up to vote on this title newly created TAGR are defin
The attributes values for the Notthe useful Useful the current settings of the other gadgetson form ( Tag Template Reference , etc.), so set these as explained in the following paragraphs before you create the TAGR.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Tag Rule Library Administration
Specifying the Elements to which Rules Apply
You can specify the type of element or a list of named elements, as follows: To specify the of element to which the current TAGR is to be applied, select a design element class from the Tag drop-down list. Criteria for Tag Rule Application
To apply restrictions to the elements specified by the Tag option, type a PDMS expression into the With text box. For example, if the Tag gadget specifies Branches, you might use the With qualifier to enter ‘(HBOR GT 100) AND (TBOR GT 80)’ to compile the overall specification ‘Branches with HBOR greater than 100 mm and TBOR greater than 80 mm’. Associating a Label Template with a Tag Rule
To select a label template that will define the appearance of tags generated by the current TAGR, use the Template Reference Select button. You will be presented with a Select Template for Auto Tagging form. On this form, select the Label Library required and, from the displayed You're Reading a Preview templates, pick the one which is to be associated with the current TAGR. full access with a free trial. TAGR. Apply this to the current Unlock Associating a Drawlist with a Tag Rule With Free Trial Download
To specify a drawlist which is to be associated with the current TAGR (such that only items in the drawlist will be tagged), click the Drawlist Reference button. You will be presented with a Drawlist Reference form. O this form, select the Drawlist Library required and, from the displayed list pick the Drawlist which is to be associated with the current TAGR. Apply this to the current TAGR.
To modify the content of the drawlist associated with the current TAGR, Sign up to vote on this title click the Drawlist button. You will be presented with a Drawlist Useful Not useful Management form. On this form, select the Drawlist whose member list is to be modified and add or remove design elements. Apply this to the
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
13
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Administration
This chapter explains what the DRAFT Administrator must do to s a project to allow Automatic Drawing Production (ADP) for Pipewor Steelwork.
DRAFT provides for three types of Automatic Drawing Production ( •
General ADP, used for Equipment and Piping. See Section 13.1
•
Steelwork Detailing. See Section 13.2.
•
Hanger and Support ADP. The Administrator's role is setting u suitable backing Sheets, as described in Section 13.3. The User information for Hangers and Supports ADP is given in Support Design Using PDMS .
ADP administration is accessed through the Automatic Dra You're Readingand a Preview Production Application, not through the Administration Application.Unlock Thefull forms access and with a menu free trial. options are only available are a member of the DRAFTADMIN team. Download With Free Trial
13.1 General ADP
The General ADP options create drawings from specified parts of th Design model in the usual way, and then add annotation according defaults set up by the System Administrator.
The defaults are stored in files, and there are different defaults suit Sign up to vote on this title for different types of drawings. The user must load a suitable file fo Useful Not useful drawing being produced.
The ADP application can add dimensions, labels, and schedules to a
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Administration
For each type, you can set up Rules using PML expressions to define how different PDMS element types are dimensioned.
13.1.1
Setting the ADP Defaults
The ADP Defaults are set on the ADP Defaults File Editor form, which is displayed when you select Settings > General ADP Defaults from the Main ADP Menu. There are several defaults files supplied with the product, stored in the directory %PDMSDFLTS%. The file names are of the form DRAGENADP -*. These files can be modified, and you can create your own new files as well. You can load a defaults file in the following ways: •
Select File > Load From from the menu at the top of the form. A File Browser will be displayed, showing the files in the given directory. Select the file you want.
•
Press the Browse button onReading the body of the form. A File Browser will You're a Preview be displayed.
•
If you already have an ADP Drawing displayed, you can select From View and pick any item in the View. The Defaults file used to create Download With Free Trial the View will be loaded.
Unlock full access with a free trial.
When a defaults file is loaded, the ADP Defaults File Editor form will be filled in with details from the file. You can change the defaults as described in the following sections. The File Header text box shows a description of the type of defaults.
The text boxes labelled Type 1, Type 2 and Type 3 show the type of dimensioning controlled by the given types.Sign Asup supplied, Type to vote on this title1 is Piping Type 2 is Equipment and Type 3 is Gridline. types are used in all Usefulall Not useful Not default files: when a type is not used in the current default file it is shown on the form as Unused. To change a type of dimensioning, click on
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Admini
The General ADP Defaults Form
The General ADP Defaults form is displayed when you press General ADP Defaults File Editor form. This form allows you to: •
Restrict USER Access . If this button is switched off, users will be to access the Modify User Defaults form and so change the defaults
this button is switched on, users will not be able to modify the defaults files from the user forms. The only way to change them be from this form, which is only accessible to users who are mem of the DRAFTADMIN team. The Modify button on the Modify Use Defaults form and the Edit button on the View Function form will n active. •
Set the Annotation Processing Order. In the text box, enter the or which different types of annotation are to be processed. As supp the order is 3, 2 1. Each Type Defaults form has an option wher can define how dimension points are handled, by spec which Type they are copied from: the processing order must ens that the dimension points to be copied already exist. Type 3
You're Reading a Preview Unlock full access Typewith 2 a free trial.
Type 2 dimension point
Download With Free Trial from Type 3 inherited
•
Create any Representation Rulesets needed. If the standard Representation Rulesets are required, this text box should conta the text Standard.
•
ed o Create any rules needed to controlSign which are ADD up toelements vote on this title byUseful volume. all REMOVEd from Drawlists defined Not supplied, useful As elements within the Volume will be added, but elements of type that are owned by a Zone with Function set to Heating or Electr
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Administration
For more information on the forms, see the online help.
13.1.2
Creating a Tagging Library
The tagging facilities used in ADP are based on the standard DRAFT automatic tagging functionality. You need to be familiar with this before reading any further. The ADP PGA defaults file contains an entry to allow the administrator to define what tag rule set element will be available to the user during use of the ADP system. The supplied system refers to a TRLB called DRA/PRJ/ADP/TAGGS/PGA that contains the TRST’s that the user accesses on the tagging creation form. Each TRST is represented by toggle gadgets on the user’s form.
In order to create your own TRLB for tagging you simply create the TRSTs and their TAGR elements with tag rules and tagging templates a required. The only important consideration for the ADP system is that the last part of the TRSTs name is used on the user’s form, and so this should describes the tagging available the user. You're Reading atoPreview For example, if the TRSTUnlock is named /MYTAG/Instruments, then Instruments full access with a free trial. will appear on the user’s tagging creation form.
Downloadare Withprovided Free Trial in the label libraries Some example tagging templates DRA/PRJ/ADP/TAGGS/PGA/TXTM and DRA/PRJ/ADP/TAGGS/PGA/SYTM but you are free to define or use any symbol or text template as required.
13.1.3
Creating a Schedule Library The schedule facilities used in ADP are based on the standard DRAFT Sign up to vote on this title automatic tagging functionality, and you should be familiar with this Useful Not useful before reading any further.
The ADP PGA defaults file contains an entry to allow the administrator
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
1
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Admini
by the user. The TRSTs and their constituent TAGRs have to be bu with the following naming conventions: TRST
TAGR
/MySchedules/Nozzles
owner-name /LOCAL
owner-name /ENTRY
TAGR /LOCAL can reference any STYM or TXTM as required. This rule is responsible for generating the tags local to the design graphi
TAGR /ENTRY has to reference a special SYTM which in turn has references to other SYTMs and is responsible for generating the tab format entries generated as part of the schedule. In order to genera matching set of local and table tags it is important that both TAGR the same criteria.
The SYTM referenced by the TAGR /ENTRY has an associated set o SYTMs as shown below, where prefix can be any prefix name for SYTMs, but the same prefix is used to identify all three SYTMs req to construct the schedules table. Example
You're Reading a Preview
Unlock full access with a free trial. The following example is based on the Project Libraries supplied in Sample Project, under DRA/PRJ/ADP/SCHED:
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Administration
TRST /NOZZLES-1
SYTM
TMRF
prefix /ENTRY
Reference by name from prefix /ENTRY
TAGR /NOZZLES/LOC
SYTM
TAGR /NOZZLES/ENTRY
prefix /HEADER Reference by name from prefix /ENTRY
TMRF
SYTM
Defines offset between entries
TXTM
prefix /OFFSET
TXTM BTEX 'X0 Y-10'
Defines label in View
Schedule Nozzle N1
Nozzle Schedule Size North East Elevation 200
+1100 +200
+3100
You're Reading a Preview Unlock full access with a free trial.
View
Download With Free Trial N1
Each of the functions of the three schedule table SYTMs is explained below: Sign up to vote on this title prefix /ENTRY
Useful to Not useful the table used The SYTM construct entries
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Admini
BTEX = ’X 0 Y -10’
This means that each table entry is offset by -10 in the Y direction, therefore producing a vertical table that grows down the sheet from origin position.
The origin and extent positions for any schedules created are initial taken from a special note created in the BACK by the administrato the next section for details of how to implement this.
13.1.4
Backing Sheet Controls
The backing sheet referenced by an ADP sheet can contain two sets information to allow the ADP annotation and view creation to be m automated. The following sections describe the types of additional information that can be generated under a BACK for use by the AD system.
The general ADP application makes use of special information store the backing sheet in the form of Notes, which specify where certain You'reby Reading a Preview of annotation generated ADP will be located on the sheet. If this information is not present on the backing sheet the application will Unlock full access with a free trial. either prompt the user for input or not allow the user access to the associated automatic annotation options. Download With Free Trial
All the Notes have visibility set to false. Reference Drawings
This is the area on the Sheet that is available for the user to insert of Reference Drawings. It is defined under a Note named back_sheet_name /REFDRWGS. The Note contains TEXPs that are to represent reference drawings associated with a sheet. Each TEXP should be positioned and have attributes required. Sign set up toas vote on this title The TEXP copied from the backing sheet onto the user’s sheet during reference Useful Not useful drawing definition.
The Note should also contain a rectangle whose area represents the
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Administration
Schedules
This is the area on the Sheet that will be used to display Schedules. The origin of the schedule table and its maximum extent is defined on the backing sheet. Only one origin and extent definition can be added to a BACK and this is initially used by ALL schedules that are created by the user. The user always has the option to re–define the two attributes for any schedule created. The ORIGIN and EXTENT information gives the application a starting point for any schedules. To create the ORIGIN and EXTENT positions on the backing sheet create a NOTE under the required BACK with the name back_sheet_name /SCHEDULE. This note should own two MRKP elements named: back_sheet_name /SCHEDULE/ORIGIN and back_sheet_name /SCHEDULE/EXTENT SCHEDULE/ORIGIN should be positioned where the origin of the schedule will be positioned and from where the schedule will be built.
SCHEDULE/EXTENT should be positioned at a point past which the schedule should not be built. All subsequent schedule entries that would You're Reading a Preview exceed this extent position are hidden and the user is warned of the Unlock full access with a free trial. schedule overflow. Keyplan
Download With Free Trial
This is the area on the Sheet that will be used to display a Keyplan. It is defined under a Note named back_sheet_name /KEYPLAN. This note should contain one MRKP element to determine the position for the Sheet’s keyplan OLAY. The MRKP must be named: back_sheet_name /KEYPLAN/ORIGIN.
The Note should also contain a rectangle whose area represents the available area taken by the reference drawing texts, which is useddurin Sign up to vote on this title zoom operations. Useful Not useful
Title
This is the area on the Sheet that will be used to display the title block of
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Admini
Summary
The following table summarises the special Notes that can exist on backing sheets, and more details are given below. Name
Use
Action if not present
/REFDRWGS
Reference Drawing Information
GUI gadgets inactivat
/LIMITS
Defines available sheet area
Whole sheet area ass
/SCHEDULE
Defines schedule position info
User prompted for pos
/KEYPLAN
Position for keyplan OLAY
Positioned at X0 Y0
/TITLE
Area for zooming on TITLE BLOCK
GUI gadgets inactivat
You can refer to the standard A0 backing sheet, /DRA/MAS/BACKS/METRIC/A0, in the Department Draft_Librarie an example. You're Reading 13.2 Steelwork Detailing ADPa Preview Unlock full access with a free trial.
This Section describes the administration tasks which you will need carry out for Steelwork Detailing Automatic Drawing Production (S Download With Free Trial which allows the DRAFT User to produce dimensioned and annotat drawings of the most commonly used structural elements (straight Beams and Columns, and flat Plates) automatically. The requirements for SDA are: •
A Sheet Library containing suitable backing sheets
•
A Symbol Library containing suitable annotation symbols Sign up to vote on this title
•
A Style Library containing suitable styles
•
A Representation Rules Library containing rules defining which Styles are used for displaying the profiles.
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Administration
The backing sheets and SDAOPT elements supplied with the product are in the Department Master_Libraries. The backing sheets in the Library DRA/MAS/BACKS can be used for SDA. The Library DRA/MAS/SDADP contains Libraries of Styles, Symbols and Representation Rules for SDA. It also contains two SDAOPT elements: SDA-Default SDA-Main-Views
The only difference is that the SDA-Main-Views file will not output detai views. : Occasionally fabrication drawings produced by SDADP will be under-dimensioned, although it will always be at least 70% of that required for fabrication of the component. If a dimension is missing, it may be due to the way the catalogue component is defined.
13.2.1
The SDA Options The attributes of the SDAOPT element define the options that will be Reading Preview used. You can change theYou're attributes ofaan SDAOPT element or create a new one using the Steelwork described in Drawing Detailing Unlock full accessOptions with a free form, trial. Production Using PDMS . With Free Trial controls which The UPDCB attribute of Download the SDAOPT element customisation macro is run: it is set to: %PDMSDFLTS%/DRA-SDADP-MACRO
See the next section for information about the macro.
If you create your own SDAOPT element, it will be created in the curren LIBY, if there is one. If your current element is the World, a new LIBY will be created to store the options in. You will have to give this LIBY a Sign up to vote on this title suitable name, if required, after the SDAOPT element has been created.
13.2.2
The SDA Customisation Macros
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Admini
customisation macro is called once for each major item created by S This means that you can define the parameters used to draw each t element.
Note that the supplied macros do not name the DEPTs REGIs and DRWGs created by SDA. You will have to give them suitable names required, after an SDA run.
13.3 Hangers and Supports ADP
This section describes how the backing sheets supplied for Hanger a Supports ADP are set up. The Sheets are supplied in the Library
Each Backing Sheet contains twelve member notes. Each Note own TEXPs to help define the specific area of the sheet. Some TEXPs ar used at this release, and some Notes contain 2D primitives that are used at this release.
The TEXPs must be kept as members of certain Notes for the DRAF GUI to work correctly. The valuesa in the BTEXT of the TEXP eleme You're Reading Preview can be whole numbers, decimals or fractions. Unlock full access with a free trial.
The standard backing sheet has the following members. Those mar with an asterisk areDownload required,With theFree other are optional. Trial *
NOTE 1
/DRA/MAS/H&S_A2/HS_Matl_List
*
NOTE 2
/DRA/MAS/H&S_A2/Frame
*
NOTE 3
/DRA/MAS/H&S_A2/Supported_Items
*
NOTE 4
/DRA/MAS/H&S_A2/Support_Steel
NOTE 5
/DRA/MAS/H&S_A2/TitleBlock
NOTE 6
Sign up to vote on this title /DRA/MAS/H&S_A2/TitleBlockData
NOTE 7
/DRA/MAS/H&S_A2/DrawingNotes
NOTE 8
/DRA/MAS/H&S_A2/Address
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
1
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Administration
NOTE 1: /DRA/MAS/H&S_A2/HS_Matl_List
This Note contains TEXPs that define settings for the Hanger Bill of Materials. The Members of this Note do not have to be named. TEXP 1
BTEX attribute set to H&S_MATL_LIST:value1, value2 where value1 and value2 specify the starting point of the
Bill of Material. This position is based on the lower lefthand corner of the owning BACK size. TEXP 2
BTEX attribute set to
REF_X:value where value sets the horizontal (X) placement of the part
number hanger element in the BOM, The position is a specified distance from the left-hand edge of the BOM area defined by TEXP 1. TEXP 3
BTEX attribute set to
DESC_X:value where value sets the horizontal (X) starting position of th
hanger element in the BOM. The position is a specified You're Reading a Preview distance from the left-hand edge of the BOM area defined Unlock full access with a free trial. by TEXP 1. TEXP 4
BTEX attribute setWith to Free Trial Download
DESC_MAX_CHAR_X:value where value specifies the number of characters allowed in
each line of the material description. Additional characters will wrap onto the next line. TEXP 5
BTEX attribute set to DIAM_X:value where value specifies the distance from the left edge of Sign up tosetting vote on this title hanger the BOM area when the diameter of the Useful Not useful element is to be placed
TEXP 6
BTEX attribute set to
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
1
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Admini
TEXP 8
BTEX attribute set to
LINE_SPACE:value where value specified the distance between each line
the description part of the BOM. TEXP 9
BTEX attribute set to
ITEM_SPACE:value where value specifies the distance between each par
number description down the BOM listing. TEXP 10
BTEX attribute set to UNBOLT_PACK_EXCLUDE:word, word Not used at this release
TEXP 11
BTEX attribute set to
LAYE_PURP:word where word specified distance from the left-hand ed
the BOM area defined by TEXP 1. TEXT 12- BTEX set to SLAB_SORF:name
The You're name Reading specified is that of the TAGR to be referen a Preview for the support labels Unlock full access with a free trial.
NOTE 2 /DRA/MAS/H&S_A2/Frame
Download With Free Trial This Note contains the 2D drafting primitives that define the main backing Sheet border, similar to the backing sheets for standard dra sheets.
NOTE 3 /DRA/MAS/H&S_A2/Supported_Items
This Note displays a table that lists the pipes that are being suppor TEXP 1
TEXP 2
BTEX set to BOM:SIB
Sign up to vote on this title
Not used at this release Useful
BTEX set to
HEADER_POS:value1,value2
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Administration
TEXP 4
BTEX set to TILE_X:value where value is the horizontal distance between the reference SLABs in the support item table.
TEXP 5
BTEX set to TILE_Y:value where value is the vertical distance between the referenc SLABs in the support item table.
TEXP 6
BTEX set to TILE_MAX:value Not used at this release
TEXP 7
BTEX set to TAGGING:name where name is the name of the TRST to be used for the supported items listing. The TRST has two member TAGRs, LOCAL and LABEL. These TAGRs are copied into the appropriate layer and the member SLABs that are generated reference them. You're Reading a Preview The LOCAL TAGR defines criteria for locating the Part Unlock full a free trial. Number SLAB inaccess thewith Views. The LABEL TAGR defines criteria for the Support Table With Free Trial label template. BOM andDownload references that specific
TEXP 8
BTEX set to TITLE:text where text is used in the log file to mark the start of messages relating to symbolic labels in the supported item layer owned by the View.
NOTE 4 /DRA/MAS/H&S_A2/Support_Steel
up to vote this title This table displays the list of member parts,Sign listing theonsize of each Useful Not useful member and its required length.
TEXP 1
BTEXT set to BOMST:STB
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Admini
TEXP 3
BTEX set to
LABEL_POS:value1,value2 where value1 and value2 define the position of the f
SLAB in the steel BOM list. This position is the dist from the lower left corner of the owning BACK. TEXP 4
BTEX set to TILE_X:value where value specifies the horizontal distance betwee SLABs in the support material list.
TEXP 5
BTEX set to TILE_MAX:value Not used at this release
TEXP 6
BTEX set to TILE_Y:value where value specifies the vertical distance between SLABs in the support material list.
TEXP 7- BTEX set to
TAGGING name a Preview You're :Reading where name specifies the name of the TRST that ow Unlock full access with a free trial.
TAGRs to be used for the support items listing. TEXP 8
BTEX set to With Free Trial Download TAGGING:name where name specifies the name of the TRST that ow TAGRs to be used for the structural support steel lis BOM. The TRST has two member TAGRs, LOCAL a LABEL. These TAGRs are copied into the appropria layer and the member SLABs that are generated reference them. the P The LOCAL TAGR defines Sign upcriteria to vote onfor this locating title Number SLAB in the Views. Useful Not useful The LABEL TAGR defines criteria for the Support Material Table and references that specific label
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Administration
NOTE 5 /DRA/MAS/H&S_A2/TitleBlock
This Note contains TEXPs that define the title block layout such as, date checked, approved etc. These TEXPs have the BTEX attribute set to fixed information. They are not set to extract data through hash codes. Two TEXPs in this Note are named DRA/MAS/H&S_A2/Scale and DRA/MAS/H&S_2/Proj. Both TEXPs are at specified positions on the sheet but the BTEX attribute is not set in either case. These two TEXPs are used for placement of the view scale and angle projection specified from the overall default settings. The creation of the drawing is not abandoned if the Note or the two named TEXPs do not exist. NOTE 6 /DRA/MAS/H&S_A2/TitleBlockData
The TEXPs in this Note are similar to those stored in the Titleblock Note By default, the visibility of this Note is turned off. When the H&S drawing is generated PDMS looks for a note in the backing sheet ending in TitleBlockData. To avoid an error message in the batch log file this note should exist. NOTE 7 /DRA/MAS/H&S_A2/DrawingNotes
You're Reading a Preview
This Note contains one TEXP. The BTEX is set to Unlock full access with a free trial. NOTE_WIDTH:30 Not used at this release .
Download With Free Trial
NOTE 8 /DRA/MAS/H&S_A2/Address
This Note contains one symbol. It could be used to reference a company logo symbol template and be positioned were required. NOTE 9 /DRA/MAS/H&S_A2/SmallPrint
This Note does not contain any members. NOTE 10 /DRA/MAS/H&S_A2/ModBlock
Sign up to vote on this title
usefullayout of Useful area Not This Note contains TEXPs that define the revision block the AVEVA backing sheet. These TEXPs have the BTEX attribute set to fixed information. They are not set to extract data through hash codes.
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Admini
the drawing title attribute and lines 108 and 109 set the sheet title attribute. NOTE 12 /DRA/MAS/H&S_A2/LIMITS
This note contains one rectangle. The rectangle defines the area on hanger and support drawing where the Views will be created. It sho be noted that placement and sizing of this rectangle should be kept of the Supported Item and Support Steel BOM lists to maintain clar
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
Download
News
Documents
Sheet Music
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
ADP Administration
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
14
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
AUTODRAFT Administration
The AUTODRAFT option of the Administration menu allows you to ac the AUTODRAFT (allowing you to convert symbols created in AutoCAD into a form usable by PDMS) and the (allowing you to take drawing frames created in AutoCAD and conv them into a PDMS usable format).
You can also import symbols and sheet frames created in AutoCAD used in PDMS.
14.1 Accessing AUTODRAFT Administration To display the AUTODRAFT Administration menu bar, select Draft>AUTODRAFT. The menu hierarchy is shown in Appendix A . You're Reading a Preview Unlock full access with a free trial.
14.2 Starting the Symbol Editor Download With Free Trial
The enables symbols created in AutoCAD to be conv into a PDMS DRAFT command macro that can then be used to crea equivalent symbols as DRAFT Symbol Template (SYTM) elements.
If any of the SYTMs thus defined already exist in the current DRAF Symbol Library then the old 2D primitives are deleted and replaced the new definition.
Sign to vote on this title Select Draft > AUTODRAFT to bring upupthe AUTODRAFT Useful Not useful Administration menus.
Select Edit > Symbols from the menu bar. This gives the AutoDR
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1
1.8K views
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
AUTODRAFT Administration
If you wish the file to be opened in AutoCAD to have a name other than the supplied symbols default, backspace in the AutoCAD Symbol Drawing Name text box until it is clear, then type in the new file name.
The file name in the AutoCAD Symbol Drawing Name textbox has appended to it automatically to make the AutoCAD drawing file name.
If you wish all symbols drawn in AutoCAD that have the same name as existing DRAFT symbol templates in the selected Symbol Library to overwrite the DRAFT symbol templates when they are imported from the Symbol Editor, click on the Replace All Symbols button. (If this option is not set, you will still be given the option, at the import stage, to overwrite symbols individually.)
Specifies whether imported AutoCAD symbols will overwrite existing DRAFT symbol templates of the same name.
You're Reading a Preview
Specifies destination for imported AutoCAD symbols.
Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Click on one of the option buttons as required: Useful
Not useful
New Drawing creates a new, empty AutoCAD drawing for use by the Symbol Editor. (If an AutoCAD drawing of the same name already
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
AUTODRAFT Admini
If you wish the Symbol Library (SYLB) that you wish to contai returning Symbol Editor-generated symbols to be other than t shown current element (as selected at step 6), backspace in the Symbol Library Name text entry box until it is clear, then type the required name.
Click on OK. After a short pause, the AutoCAD text window an graphics window (with the specified drawing displayed within will appear.
14.3 Starting the Frame Editor
The enables drawing frames created in AutoCAD to b converted into a PDMS DRAFT command macro that can then be u create the equivalent frames as DRAFT Backing or Overlay Sheet elements within a specified Sheet Library.
If the specified Backing/Overlay Sheet already exists in the specifie Sheet Library then the old 2D primitives are deleted and replaced b You're Reading a Preview new definition. Unlock full access with free trial. Select Draft > Administration to bring up the > aAUTODRAFT AUTODRAFT Administration menus.
Download With Free Trial
Make the Sheet Library (SHLB) that you wish to contain the returning Frame Editor–generated symbols the current eleme Select Edit > Sheet Frame from the menu bar. This gives the AutoDRAFT Frame Editor form:
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
AUTODRAFT Administration
If you wish the AutoCAD work directory to be other than the local one, backspace in the AutoCAD Work Directory text box until it is clear, then type in the required directory name.
If you wish the file to be opened in AutoCAD to have a name other than the supplied default, backspace in the AutoCAD Drawing Name text box until it is clear, and then type in the new file name. The file name in the AutoCAD Drawing Name text box has appended to it automatically to make the AutoCAD drawing file name. Click on one of the option buttons as required:
New Drawing creates a new, empty AutoCAD drawing for use by the
Frame Editor. (If an AutoCAD drawing of the same name already exists then you are asked if you wish to continue (i.e. update it, as below), the alternative being to return to DRAFT.) Open existing Drawing opens an existing Frame Editor drawing.
Specify the AutoCAD drawing units to be used by selecting from the You're Reading a Preview Units option button. Unlock full access with a free trial.
If you wish the Sheet Library (SHLB) that you wish to contain the returning Frame Editor-generated symbols Download With Free Trial to be other than the shown current element (as selected at step 6.), backspace in the Symbol Library name text box until it is clear, then type in the required name.
Select from the option button at the bottom–left of the form whethe you wish the imported symbols to create a Backing Sheet or an Overlay Sheet. Enter the name that you wish to give the derived Sheet into the Sign up to vote on this title name text box.
Useful
Not useful
Click on OK. After a short pause, the AutoCAD text window and graphics window (with the specified drawing displayed within it)
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
AUTODRAFT Admini
provided you first navigate to the correct position in the dat hierarchy, the macro file exported from AutoDRAFT can be into the DRAFT database using the PDMS $M/ command.
If PDMS and AutoCAD are on the hardware platform Symbol or Sheet elements created using AutoCAD can be cr in the DRAFT database directly from AutoDRAFT. See the AutoDRAFT Reference Manual for details.
Having created entities in AutoCAD (using the AutoDRAFT ) which can be used as Symbols in DRAFT, they can be impor DRAFT and Symbol Template (SYTM) elements crea Select Draft>AUTODRAFT to bring up the AUTODRAFT Administration menus. Select Import>Symbols . . . from the menu bar. This gives the AutoDRAFT Symbols form.
If the directory to contain the Symbol creation macro file is not local one, backspace in the AutoCAD Work Directory text box u it is clear, then type in the required directory name. You're Reading a Preview
If the macro file to be used does not have the supplied default Unlock full access with a free trial. symbols.mac then backspace in the AutoCAD Symbol Macro te box until it is clear, then type in the new file name. Download With Free Trial
Press OK, and a Backing or Overlay Sheet will be automatical created.
If you wish all symbols drawn in AutoCAD that have the same name as existing DRAFT Symbol Templates in the selected Sy Library to overwrite the DRAFT Symbol Templates when they imported from the Symbol Editor, click on the Replace All Sym button. (If this option is not set, you will still be given the optio Sign up to vote on this title the import stage, to overwrite symbols individually.)
Templates are to b The Symbol Library (SYLB) to which the Symbol added is as specified on entry to the Symbol Editor, see page NO TA Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
AUTODRAFT Administration
Select Draft>AUTODRAFT to bring up the AUTODRAFT Administration menus. Select Import>Sheet Frame from the menu bar. This gives the Load AutoDRAFT Sheet Frame form.
If the directory to contain the Sheet-creation macro file is not the ‘local’ one, backspace in the AutoCAD Work Directory text box until it is clear, then type in the required directory name. If the macro file to be used does not have the supplied default name pdmsback.mac then backspace in the AutoCAD Sheet Macro text box until it is clear, then type in the new file name. When you press OK, a Backing or Overlay Sheet will be automatically created. The type of Sheet to be created, and the Sheet Library (SHLB) to which the Sheet is to be added are both as specified on entry to the Frame Editor.
If the specified Backing/Overlay Sheet already exists in the specified Sheet Library then the old 2D primitives are deleted and replaced by the You're Reading a Preview new definition. Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
15
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Loading Data Files
The Administration option of DRAFT contains a feature that allows y automatically load data files to create new projects. By using the Data File option you can load new project data for Main Libraries, Tem Drawings and Application Department.
15.1 Accessing Load Data Files
To load the data files, select Draft > Settings > Load data file from the DRAFT main menu. You can then select the data files you wish to load ( Main Libraries Template Drawings or Application Department). You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
Download
News
Documents
Sheet Music
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Loading Data Files
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
16
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Updating the Database
There are occasions when the DRAFT database needs to be updated specifically, as opposed to the routine updating that occurs from tim time in normal use. This chapter explains when and how you shoul this.
16.1 Updating Picture Files
This operation should be carried out to recover from a corrupt pictu file, such as may result from a RECONFIGURER operation, or if an attempt has been made to display a VIEW created using a previous version of DRAFT.
Annotation graphicsYou're will always restored but Design graphics m Reading be a Preview be. In all such cases, a message alert will be displayed instructing y full access with trial. carry out the updateUnlock operation, anda free this is the only time that the operation should be carried out. Download With Free Trial
Select Graphics > System Update > Picture from the Administration m
16.2 Updating Template Instancing
This option (valid at SHEE, BACK, OVER, SYLB or LALB level, or above) scans the database hierarchy and updates all those parts of picture files that use the graphics ‘instancing’ mechanism. Sign up to vote on this title For exam a SYMB is an ‘instance’ of a SYTM. OLAY and BACK elements are Not useful Useful same category.
This update should be used to generate the correct graphics after th
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Updating the Database
16.3 Updating Cross-DB Reference Attributes
This option updates all DRAFT element attributes that refer to elements in the Design database. The settings of such attributes exist as database reference numbers.
The updating function operates on the current element. It should only be used if the Design database has been deleted and rebuilt from macros. See Appendix C of the VANTAGE PDMS DRAFT User Guide for further details. Select Graphics > System Update > Refs from the Administration menu.
16.4 Updating Cross-DB Name Attributes
DRAFT elements with attributes that refer to elements in the Design database (the settings of which exist as database reference numbers) als have (hidden) text attributes set to the names of the referenced elements This option updates the latter using the settings of the You're attributes, Reading a Preview associated reference attributes. Unlock full access with a free trial.
The updating function operates on the current element. It should only be used if the Design database has been and rebuilt from macros. Download Withdeleted Free Trial See Appendix C of the VANTAGE PDMS DRAFT User Guide for further details.
Select Graphics > System Update > Names from the Administration menu.
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
1
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
A
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
The DRAFT Administrator Menus
A.1 The Main DRAFT General Administrative Menu
The Administrative menu options that are different from User Applications are shown in bold. Options that are comm all the Administrative Applications are only shown on the General Administration menu. This Section shows the part of the menu hierarchy that is common to all Applications. Draft
Display
Graphics
Query
Settings
Utili
You're Reading a Preview
System Save Work Update > Unlock full access with a free trial. Global Getwork System Update > User Defaults Extract Control Point Construction Session Comment . . . Download With Free Trial Units Select Working Library. . . Picture Enhance Colour Sheet Libraries . . . Instances Feedback Colour Symbol Libraries . . . Refs Ppoint Display Isodraft Symbol Libraries . . . Names System Defaults LabelSheet LibrariesLibrary ... A.2 Administration User Defined Pen Set AutoDRAFT . . . Design Plotting Defaults Style Libraries . . . DXF Configuration S Representation Rules . . . Utilities Design Changes Settings Create Annotation DGN Configuration S Drawlist Libraries . . . Annotation Changes Load Tagging Rules . . . Sign up to vote on this Data title Files Tagging Area ADP . . . Note Useful >Not useful Back/Over Tagging Regenerate User Applications Library . . . Layer All Modules > Sheet Library . . . Exit Load Text . . A . ll Changes Group Filter . . .
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
The DRAFT Administrator Menus
: The Draw, Construct and Edit options are the same as in the 2D Drafting Application.
A.3 Symbol Library Administration Settings
You're Reading a Preview
Utilities
Create
Unlock full access with a free trial.
Library . . .
Download With Free Trial Symbol Library . . . Group Filter . . . Icon Menu Styles . . .
Load Text . . . Sketch Drafting . . . Dynamic Primitives
Symbol Template . . .
Sign up to vote on this title
Modify
Useful Delete
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
The DRAFT Administrato
A.4 ISODRAFT Symbol Library Administration Create Settings
Utilities
Group Filter . . .
Library . . . Isodraft Symbol Library Isodraft Symbol Templat
Load Text . . . Sketch Drafting . . . Dynamic Primitives Export Isodraft Symbols Import Isodraft Symbols
Modify
Delete
Name Hierarchy > Symbol Library > Symbol Template . . .
You're Reading a PreviewCE
Members Owner Unlock full access. with Definition . . a free trial. Owner Members Attributes . . . Group Members
Download With Free Trial
: The Construct and Edit options are the same as in the 2D Drafting Application. Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
The DRAFT Administrator Menus
A.5 Label Library Administration
Settings
Utilities
Library . . . Label Library . . . Text Template . . . Symbol Template . . .
Load Text . . . Sketch Drafting . . . Dynamic Primitives
Group Filter . . . Icon Menu Styles . . .
Modify
Name Hierarchy Library . . . Label Library Text Template Symbol Template
Create
Delete
You're Reading a Preview
Unlock full access with a free trial.
> > > ..
CE Members Owner Download With Free Trial Owner Members Definition . . . Group Members Attributes . . .
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
The DRAFT Administrato
A.6 AUTODRAFT Administration
Edit
Symbols . . . Sheet Frame . . .
Import
Delete
Symbols . . . Sheet Frame . . .
CE Members Owner Owner Members
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
1
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
The DRAFT Administrator Menus
A.7 Style Library Administration
Create
Library . . . Style Library . . Hatching Library . . Change Design Library . . . Change Annotation Library . . .
Delete
Modify
Name Hierarchy > Library . . . Style Library . . Hatching Library . . . Change Design Library . . . Change Annotation Library . . .
CE Members Owner Owner Members
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
1
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
The DRAFT Administrato
A.8 Representation Rule Administration Create
Library . . . Representation Library . . . Representation Ruleset . . . Hatching Library . . . Hatching Ruleset . . . Change Library . . . Change Ruleset . . .
Delete
Modify
Name Hierarchy > Library . . . Representation Library . . . Representation Ruleset . . . Hatching Library . . . Hatching Ruleset . . . Change Library . . . Change Ruleset . . .
CE Members Owner Owner Members
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
1
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
The DRAFT Administrator Menus
A.9 Drawlist Library Administration
Create
Library . . . Drawlist Library . . . Drawlist . . .
Delete
Modify
Name Hierarchy > Library . . . Drawlist Library . . . Drawlist . . .
CE Members Owner Owner Member
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
The DRAFT Administrato
A.10
Tagging Administration
Create
Library . . . Tagrule Library . . .
Delete
Modify
Name Hierarchy > Library . . . Tagrule Library . . .
CE Members Owner Owner Mem
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
B
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
The DRAFT Database Hierarchy
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines News
Documents
Sheet Music
Save
Embed
Share
Print
Download
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
The DRAFT Administrator Menus
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
1
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
C The Libraries Supplied with DRAFT The DRAFT Libraries supplied with the product are stored in two Departments: •
Master_Libraries can be referenced from any project.
•
Project_Libraries contain rules that are Project-specific.
This appendix summarises the contents of the two Departments.
You're Reading a Preview Unlock full access with a free trial.
Download With Free Trial
Sign up to vote on this title
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Sign In
Upload
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
The Libraries Supplied with DRAFT
Master Libraries DEPT
Master_Libraries LIBY
DRA/AID
SHLB
DRA/AID/PENS
BACK
DRA/AID/PENS/HSEL
Hatching patterns BACK
DRA/AID/PENS/NSEL
User-defined pens BACK
DRA/AID/PENS/MSEL
Marker symbols BACK
SHLB
DRA/AID/FONTS
SYLB
DRA/AID/FRAMES
LIBY
DRA/MAS/H&S
DRA/AID/FONTS/SELECTION
Font selection SYTM
DRA/AID/FRAMES/CN
SYLB You're Reading a Preview
SYTMs for H & S ADP
Download With Free Trial LALB
SYTMs for H & S ADP
SHLB
BACKs for H & S ADP
TRLB
TRSTs for H & S ADP
RPLB
Sign up to voteRRSTs on this title
DRA/MAS/H&S/SYMBOLS DRA/MAS/H&S/SYMBOLS2 Unlock full access with a free trial. DRA/MAS/H&S/LABELS DRA/MAS/H&S/BACKS DRA/MAS/H&S/TAG_RULES DRA/MAS/H&S/RULESETS Useful
RPLB
DRA/MAS/H&S/STYLES
etc
Frame aids
for H & S ADP
Not useful
STYLs for H & S ADP
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
DRAFT User Guide Part1
1
Download
News
Documents
Sheet Music
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
The Libraries Supplied with
DEPT
Master_Libraries continued
REGI
DRA/MAS/LABELS LIBY
DRA/MAS/LABELS/GEN LALB
DRA/MAS/LABELS/GEN/USERDEF
SYTMs templates containing ATEXTS SYTMs for geodetic labels datums top of steel steelwork positions column labels equipment tables pipe end symbols
LALB
DRA/MAS/LABELS/GEN/EL-GEO
REGI
DRA/MAS/SYMBOLS LIBY
DRA/MAS/SYMBOLS/GEN You're Reading a Preview SYLBs
Unlock full access with a free trial.
DRA/MAS/SYMBOLS/GEN/GRATINGS etc
Download With Free Trial
SYTMs for Gratings, slopes, welds, pipe breaks, sections markers, direction arrows
LIBY
DRA/MAS/SYMBOLS/ELE SYTMs for DRA/MAS/SYMBOLS/GEN/GRATINGS Intercoms, etc receptacles pushbuttons fire alarms switches, etc Sign up to vote on this title
SYLBs
LIBY
DRA/MAS/SYM-LAB-BACKS
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
News
Documents
Sheet Music
DRAFT User Guide Part1
1
Download
Join
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
The Libraries Supplied with DRAFT
Project Libraries DEPT
Project_Libraries Each of the following REGIs contains Drawings, Sheets and Libraries for different standard sheet sizes for appropriate discipline REGI
DRA/PRJ/TMP/ADP-PGA
For automatic drawing production of P
REGI
For Piping drawings
REGI
For Equipment drawings
REGI
For Electrical drawings
REGI
For Clash Plottiing
DRA/PRJ/TMP/PIPING
DRA/PRJ/TMP/EQUI
DRA/PRJ/TMP/ELEC
DRA/PRJ/TMP/CLASH You're Reading a Preview
REGI
Unlock full access with a free trial. For automatic drawing production
DRA/PRJ/TMP/ADP
Download With Free Trial Each of the following LIBYs containsstandard libraries of suitable elements LIBY
Contaiins RPLBs which own RRSTs and for various uses
LIBY
Contains RPLBs which owns RRST and for various uses
LIBY
Sign up toa vote onwhich this title Contains SHLB owns Overlay Sh defining ADP keyplans (metric and imper
DRA/PRJ/REPR
DRA/PRJ/STYL
DRA/PRJ/OVERS
LIBY
Contains TRLB which own TRSTs for Pip structural and Equipment applications
DRA/PRJ/AUTOTAG
Useful
Not useful
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1.8K views
1
Upload
Sign In
Join
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
1
Download
News
Documents
Sheet Music
DRAFT User Guide Part1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Index Access rights.......................................................2-2 Administrator
Delimiters
element names........................................
access rights .................................................... 2-2
DLEV attribute...........................................
functions ......................................................... 2-1
DRAFT defaults
ADP
DRA->SETUP ......................................
backing sheets...............................................13-7
load.........................................................
Hanger and Supports...................................13-11
save.........................................................
Keyplan.........................................................13-8
DRA-SETUP.............. ................................
Reference drawings.......................................13-7
Drawing level .............................................
schedule library.............................................13-4
Drawlist
Schedules ............................................ 13-3, 13-8
creating...................................................
You're Reading a Preview Sheet limits ................................................... 13-7 defining members............... ....................
Tagging ......................................................... Unlock full13-3 access with a freedeleting................................................... trial. tagging library...............................................13-4
Drawlist library .......................................
Download With Free Trial ADP Administration ......................................... 13-1 creating................................................... Auto tagging ..................................................... 12-1 AutoDRAFT Frame Editor............................ 14-3
drawlist................................................... Drawlists
AutoDRAFT Frame Editor form.......................14-3
creating...................................................
AutoDRAFT Symbol Editor .......................... 14-1
Element name delimiters ............................
AutoDRAFT Symbol Editor form .................... 14-1
Hanger and Supports ADP ...................
Automatic Drawing Production ........................13-1
adding annotation.............................. ...... 6-3, 8-3
Hatching Sign up to vote on this title rule sets ............................................. Useful Not useful Hatching styles ...........................................
create...............................................................5-2
ISODRAFT Symbol Libraries
Backing sheet
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join
Search
Home
Saved
1
1.8K views
Upload
Sign In
RELATED TITLES
0
PDMS DRAFT Administration Guide Uploaded by Ravi Patil
Books
Audiobooks
Magazines
Save
Embed
Share
Print
Download
News
Documents
Sheet Music
Join
DRAFT User Guide Part1
1
of 133
DRAFT+Administrator+Application+User+ PDMS Graphical Model
Search document
Index
backing sheet annotation ................................ 8-3 creating ........................................................... 8-1
for ADP ........................................................ Schedules
symbol templates............................................ 8-2
ADP ........................................................ ......
text templates.................................................. 8-3
in ADP..........................................................13
Layer purpose ................................................ 3-5
SDADP Administration....................................13
Layer purpose filter ............................................ 3-8
Searching for Libraries .......................................
Library
Sheet Libraries
searching ........................................................ 2-3
use of ............................................................
Load AutoDRAFT Sheet Frame form .............. 14-6
Sheet library........................................................5
Load AutoDRAFT Symbols form ............. 14-5
backing sheet create........................................5
Loading default settings ..................................... 3-3
creating ...........................................................
Main library........................... ............................. 4-1
overlay sheet...................................................5
Mappings, AutoCAD to DRAFT ..................... 14-5 Name conventions ............................................ 3-10 Overlay sheet
Sheet limits ADP ............................................................. . Sheet sizes ..........................................................
create .............................................................. 5-3
Steelwork Detailing ADP .................................
You're Reading a Preview
Pen drawing styles......................................... ... 3-11 Pen settings
Style attributes ....................................................
Unlock full access Style with alibrary free trial. ........................................................
device pens ................................................... 3-12
Styles
Download With Free Trial
plot pens ....................................................... 3-12
creating ...........................................................
Plot options....................................................... 3-14
deleting ...........................................................
Plotfiles HPGL format................................................ 3-14 Postscript format .......................................... 3-14
Plotting Options form ................................. 3-14
Symbol Libraries use of ............................................................ Symbol library
PURP attribute.................................................... 3-5
creating ........................................................... SYLB..............................................................6Sign up to vote on this title
Reference Drawings
Useful ............................................ symbol templates Not useful
ADP.................... .......................................... 13-7
SYTM.............................................................6-
Home
Saved
Books
Audiobooks
Magazines
News
Documents
Sheet Music
Upload
Sign In
Join