Fire Caste
Advanced Assembly A few conversions in each Fire Warrior squad can help personalise your army. Cutting and bending limbs to create running (1) and (4) or crawling poses (2). 1
Using Green Stuff to fill gaps created by posing (6), or to remodel hands (4), (5) and (6). Mixing parts from kits, such as (3), which incorporates pieces from the Tau Tank Accessory sprue.
FIREWARRIORS
Warriors of the
Fire Warriors are the Tau Empire’s front line troops, expanding its frontiers with each battle they fight. Whether fielded as solid walls of infantry, or mounted in Devilfish transports as air cavalry, no Tau army can do without its Fire Warriors.
Adding extra detail, (6) for example, has a pin for an aerial.
Basic Assembly 2
3
4
5
6
When assembling your models, consider the angle at which the warrior’s weapon is held and which way his head is looking. The weapon held up high, with the head posed at an angle looking along the gun, so the firer is aiming (1) and (3).
i
ii
Fil l
n ted ha d
sculpting nd
It might be lowered or raised, with the warrior looking away, holding fire whilst he observes an enemy’s movements (2) and (5).
R
lp cu es
ga in
1
Held to the side, while the warrior is walking (6), or held in one hand whilst the other prepares a grenade or activates a scanning device (4).
R
iv
wrist
White Dwarf
4
5
6
e po sition
oned
50
3
kne
iti os
2
Ch an ng gi
ep
iii
Using Green Stuff
To get an effect like this (i), cut the top off the the arm to create a flat surface. Varying the angle of the cut changes which direction it will point. Pin the joint for strength, then fill in the gap with Green Stuff. Leave it to dry for 20 minutes, then press lines into it with a sculpting tool to mimic the cloth of the undersuit. His hand (ii) has also been resculpted. The model at the bottom has had his wrist (iii) and knee joint (iv) similarly repositioned. He is carrying his helmet, which was made by removing the neck with a modelling knife from a Tau helmeted head.
51
White Dwarf
Details For more on layering and extreme highlighting, check out pages 38 and 40 of How to Paint Citadel Miniatures.
T’au is an arid, desert world, the favoured climate of the Tau race. The colour scheme is quite easy to paint using the Layering and Extreme Highlighting techniques, the latter being applied to the armour, over a black undercoat. Tau equipment is very hi-tech and clean, so take your time and try to be neat with your lines.
Highl igh t
2
Tau Symbol Chaos Black
Stage Four
Armour highlight (Layer) Bronzed Flesh
Sept Markings Skull White Gun Stabiliser highlight (Layer) Burnished Gold Black highlight Codex Grey
The highlighting on the armour is a mix of Layering and Extreme Highlighting. The final highlight should only be applied to the very edge of the armour.
Undersuit highlight Bleached Bone (layer) Scorched Brown
Eyepiece highlight (dot) Skull White
Armour Highlight (Extreme Highlight) Bleached Bone Bronzed Flesh
Lenses on models look great when painted like this – just paint a crescent of a lighter colour to the underside of the basecoat, opposite this, apply a dot of Skull White paint.
The Tau utilise a great many markings and insignia, many of which determine such things as the wearer’s rank and unit. These are derived from the ancient warpaint worn by the Fire caste in the earliest history of the race. Although the exact form these markings take can be varied according to your own tastes, their colour is tied to the sept from which the wearer originates. The Tau use a wide variety of stripes and circles to indicate rank, role etc. Although you don’t need to ‘translate’ them exactly, they come in handy as a simple squad numbering system. Simply count a single stripe as team one, two stripes as team two and so on. Team leaders wear the same identity stripes, but these fill larger areas of their armour.
Squad Leader Variants
Squad Leader
Lining requires a steady hand. Either apply the paint as a thin line, or water it down before painting it into recessed detail like this and wiping off the excess.
Sept Markings
Squad Numbers
Squad 3
Gun Stabiliser highlight (Layer) Shining Gold
Black highlight (Extreme) Codex Grey/ Chaos Black
Example Sept Colours
D’yanoi Sept
Black highlight (Layer) Codex Grey/ Chaos Black
2:3 mix Bleached Bone/ Shadow Grey
Squad Leader
Undersuit Scorched Brown
Undersuit highlight (Layer) Bleached Bone Scorched Brown
1:3 mix Bleached Bone/ Shadow Grey
Squad 2
Gun Stabiliser Tin Bitz
Shadow Grey (the eyes are left black).
Ke’lshan Sept
Armour Vomit Brown
Eyepiece highlight Blood Red
Squad Leader
Armour lining Tin Bitz
Stage Three
White Dwarf
Highl igh t
1
£12
Squad 1
Tau Symbol Skull White
The circular device at the end of the pulse rifle is the gun stabiliser.
52
Highl igh t
Stage Two
Eyepiece Scab Red
Undersuit highlight (Layer) Bleached Bone/ Scorched Brown
Base co at
Au’taal Sept
Stage One
Painting Tau Skin
FIREWARRIORS
The T’au Sept
3
1:1 mix Bleached Bone/ Shadow Grey
All models in an army will usually have the same colour sept markings, and the squad markings are applied to drones and transport vehicles associated with the unit.
53
White Dwarf
Many of the principles discussed in relation to the Fire Warriors apply here. Red Bas Deep eco at
Deep red basecoat mix 4 parts Scab Red 2 parts Chaos Black 3 parts Scorched Brown
Commander Shadowsun.
p Red Highl igh Dee ts
Deep red highlight mix 4 parts Scab Red 2 parts Chaos Black 3 parts Scorched Brown 1 part Bleached bone Black highlight (Layer) Codex Grey
Black highlight 2 (Extreme Highlight) Fortress Grey This Sniper Drone and Spotter have been painted by Neil Hodgson in the same colours as the ‘Eavy Metal Stealth teams, as both are equipped with stealth generators.
Stealth Team
T’au Sept Fire Warriors.
C rst Bu
annon
Drone
con tr
le ol r
Cadians are ambushed by Tau of the Sa’cea sept.
54 White Dwarf
FIREWARRIORS
Sniper Drone Team
55
White Dwarf
