Microsoft PowerPoint - 02 OEB204700 eNodeB LTE V100R006 Local Commissioning ISSUE 1

eNodeB LTE V100R006 Local Commissioning

eNodeB Local Commissioning www.huawei.com

Copyright © 2013 Huawei Technologies Co., Ltd. All rights reserved.

Contents 1. Commissioning Overview 2. Local Commissioning through the USB Disk

3. Local Commissioning through the LMT


Page1

1


Introduction to Commissioning

To ensure that the eNodeB operates normally after the installation

Commissioning Modes:

M2000-based Commissioning

USB+M2000-based Commissioning

Local Commissioning with LMT

Commissioning Scenarios:

Without a Security Gateway

With a Security Gateway

Commissioning Prerequisites:

eNodeB hardware installed and ready

Transport Network ready (for Remote Commissioning with M2000)


Page2

Scenario Without A Security Gateway


Page3

2


Scenario With A Security Gateway


Page4

Commissioning Mode – through USB M2000 Client

M2000 Server

Remote Commissioning with M2000 eNodeB


Page5

3


Commissioning Mode – through LMT LMT

M2000 Server

eNodeB


Page6

Contents 1. Commissioning Introduction 2. Local Commissioning through the USB Disk 3. Local Commissioning through the LMT


Page7

4


Procedure for the Local Commissioning through the USB Disk


Page8

Procedure for the Local Commissioning through the USB Disk


Page9

5


Prepare for the Local Commissioning through the USB Disk 1. Obtaining a Device Panel Drawing 2. Preparing a USB Flash Drive for eNodeB 3. Preparing Dialing Test Tools 4. Performing Hardware Installation and Power-On Checks 5. Preset a Bar Code Scanner 6. Download a Software Package, Data Configuration Files, and Deployment Lists


Page10

Obtaining a Device Panel Drawing Step1 Obtaining accurate installation information about the

boards and modules of a base station from Huawei technical support.


Page11

6


Preparing a USB Flash Drive for eNodeB Step1 Choose Start > Programs > iManager M2000 Client > USB Making and Protection Tool to start the tool. Step2 Choose Make USB > Path Settings. The Path Settings dialog box is displayed, as shown in the following figure. Step3 Set the local save paths for the software and files, NE type, and working mode based on the types of USB flash drive directories. Then click OK. Step4 Select the NE that requires a USB flash drive and deployment mode. Step5 Select an encryption algorithm and an integrity protection algorithm. Copyright © 2013 Huawei Technologies Co., Ltd. All rights reserved.

Page12 Step6 In the Output Path area, specify a save path.

Preparing a USB Flash Drive for eNodeB


Page13

7


Preparing a USB Flash Drive for eNodeB Step7 Click Start. Step8 Click OK in the dialog box displayed after the tool completes the making of the USB flash drive. Step9 Optional: If the Local Path option is selected in the Output Path area, copy the files to the USB flash drive.


Page14

Preparing dialing test tools Step1 Obtaining the dialing test tools. It is used to check whether the base station can perform services correctly. Commonly used tools are test terminals.


Page15

8


Performing hardware installation and Power-On Checks Step1 Ensure that the base station hardware has been installed and has passed the installation checks. Different types of base stations have different hardware installation check procedures. For details, see Installation Checklist in the installation guide of the corresponding base station. Step2 Ensure that the base station has been powered on and has passed the power-on checks. Different types of base stations have different power-on check procedures. For details, see Powering On base station type in the installation guide of the corresponding base station.


Page16

Preset a Bar Code Scanner Step1 Print the electronic operation guide on a piece of A4 paper to facilitate scanning of presetting codes. Step2 Connect the bar code scanner to the PC through a USB port. Step3 Scan the presetting codes printed on the A4 paper. Step4 Check whether the bar code scanner is preset correctly. Note: Only when deployment ID is used to bind a base station, we need to preset a bar code scanner.


Page17

9


Performing Bar-Code-Based Base Station Binding Step1 Connect the scanner to the USB port on the main control board of the base station. Step2 Use the scanner to read the deployment ID in the bar code. Step3 Check whether the scanning is successful. If the scanner emits a tone and the scanning laser turns off, the scanning is successful. Step4 Remove the scanner. Note: Only when a base station is to be bound with the deployment ID, we need to performing bar-code-based station binding.


Page18

Download & Activate the Software and Data Configuration File Step1 Insert the USB disk in USB port on the LMPT/UMPT of the BBU3900

Step2 eNodeB will automatically upgrade the software and download the data configuration file, and restart. Then verify that the loaded software and data configuration files have taken effect. Step3 Remove the USB flash drive after loading succeeds. Copyright © 2013 Huawei Technologies Co., Ltd. All rights reserved.

Page19

10


Download & Activate the Software and Data Configuration File




11




Performing Service Tests Step1 Use the UE to visit the WWW server and browse web pages. Perform this test 20 times. The success rate is higher than 95%, and the user has no difficulty in browsing. Step2 Use the UE to visit the FTP server and upload files. Perform this test 10 times. The success rate is higher than 90%, and the upload rates are stable. Step3 Use the UE to visit the FTP server and download files. Perform this test 10 times. The success rate is higher than 90%, and the download rates are stable. Step4 Use the test UE to call another UE. Perform this test 20 times. The access success rate is higher than 95%, calls are not dropped and there is not obvious noise. Copyright © 2013 Huawei Technologies Co., Ltd. All rights reserved.

Page23

12


Performing ESN-based Base Station Binding by local Step1 The local engineer reports the site position and ESN of each base station to the remote engineer.


Page24

Testing Installation and Deployment Quality Step1 A local engineer checks that the test area has no radiation and is safe for testing. Step2 The local engineer checks that all cells of the base station have been unblocked. Step3 The local engineer checks the ports and rectifies the problems. After the troubleshooting, the local engineer instructs the remote engineer to resume the commissioning task.


Page25

13


Checking Environmental Alarms Step1 The local engineer performs a loopback test on an alarm port of the UPEU using a twisted pair. The remote engineer checks whether the M2000 receives an environmental alarm from the alarm ports. Step2 The local engineer stops the loopback test. The remote engineer checks whether the alarm on the M2000 is cleared. Step3 Both local and remote engineers repeat the preceding steps until all eight of the alarm ports on the UPEU pass the tests.


Page26

Remote operations In M2000 do the procedures for commissioning, including: Performing OM channel setup confirmation Acquire an NE commissioning verification report Confirm that auto deployment tasks are completed Setting the maximum output power for RF modules Set an NE to the NORMAL mode


Page27

14


Local and Remote Cooperation The local and remote cooperation procedures for commissioning, including: Performing ESN-based Base Station Binding Testing Installation and Deployment Quality Checking Environmental Alarms Handling Alarms


Page28

Contents 1. Commissioning Introduction 2. Local Commissioning through the USB Disk 3. Local Commissioning on the LMT


Page29

15


Procedure for the local eNodeB commissioning on the LMT Start Prepare for the Local eNodeB Commissioning on the LMT Upgrade the eNodeB Software and Data Configuration File on the LMT

Establish the OM link between the M2000 and the eNodeB

Local operation .

Commission the ALD device on the LMT Commission the antenna system on the LMT Commission the environment monitoring equipment on the LMT Set the maximum TX power of RRU or RFU

Same as the operation in Remote Commissioning on the M2000

Download the License on the LMT

Remote operation

Compare the license file with the configuration data of eNodeB Set the eNodeB status End

”

“

Handle the eNodeB alarms on the LMT Query the running status of the eNodeB on the LMT Verify the basic services of the eNodeB


Page30

Prepare for the Local eNodeB Commissioning on the LMT

Arranging for Related Information and Tools Required for the eNodeB Commissioning on the LMT

Collect the information related to the eNodeB

Refer to the operation in “eNodeB LTE Remote Commissioning”

Arrange for the tools required for the local commissioning on the LMT

Laptop

Ethernet cable for connection to LMPT / UMPT

Adapter for Local Maintenance for connection to UMPT


Page31

16


Connecting To eNodeB With LMPT

Default Local OM IP address: 192.168.0.49 Setting PC IP same segment, such as: 192.168.0.88

1. LMPT 2.Ethernet Cable

3. PC


Page32

Connecting To eNodeB With UMPT Default Local OM IP address: 192.168.0.49

2

1 4

3

Setting PC IP same segment, such as: 192.168.0.88

1.UMPT

2.Adapter for Local Maintenance


3. Ethernet cable

4. PC

Page33

17


Login into Web LMT

Local OM IP address:192.168.0.49 User name: admin Default password: hwbs@com


Page34

Configure FTP Server Info

Configuring the FTP Server

Figure1. Software Management tab page Copyright © 2013 Huawei Technologies Co., Ltd. All rights reserved.

Page35

18


Configure FTP Server Info


Page36

Upgrade the eNodeB Software and Data Configuration File on the LMT


Page37

19


Software Storage

Working Main Area

Standby Activate

eNodeB Software A


Standby Area eNodeB Software B

Store downloaded software

Page38

Software Rollback

Command:

RBK SOFTWARE

Notes: Before implement software rollback, we should check if there is any valid software for rollback, using the following command:


Page39

20


Download the License on the LMT

After downloading the commissioning license to the eNodeB on the LMT, you are authorized to use the eNodeB software

Procedure

Run the INS LICENSE command to download and activate the license file on the eNodeB


Page40

Handle eNodeB Alarms on the LMT

On the LMT, click the Alarm/Event button. The Alarm/Event tab page is displayed

Check for active alarms on the Engineering Alarm tab page of the Browse Alarm/Event tab page

Double-click an active alarm. Detailed Information dialog box is displayed

Click Solution... to know the detailed information and alarm handling procedure. Clear the active alarm by following the alarm handling procedure.


Page41

21


Query the Running Status

On the LMT, click the Selftest button. On the displayed Selftest tab page, an MML command script with the complete parameter settings is automatically imported to the command area

Click the Go button. The test result is displayed in the area below the Go button


Page42

Set the eNodeB Status


Page43

22


Local Commissioning with MML Start Remove Default Configuration Data

Configure global Data

Configure Device Data

Configure Transmission Data Configure Radio Data

End


Page44

Remove Default Configuration Data


Page45

23


Configure Global Data


Page46

Configure Global Data


Page47

24


Configure Device Data (Procedure)


Page48



Page49

25




Page50



Page51

26


Configure and Commission ALDs


Page52

Commissioning RET Only

RET+STMA

RET+SBT


RET Only Page53

27


Commissioning RET and Smart Bias Tee

RET+STMA

RET+SBT


RET Only Page54

Commissioning RET and Smart TMA

RET+STMA

RET+SBT


RET Only Page55

28


Configure Monitoring Units


Page56

Configure Time and Synch. Data


Page57

29


Configure Transmission Data


Page58

Key MO to configure ADD ETHPORT

End Point ADD DEVIP ADD IPRT ADD SCTPTEMPLATE ADD SCTPHOST ADD SCTPPEER ADD USERPLANEHOST ADD USERPLANEPEER ADD EPGROUP ADD SCTPHOST2EPGROUP ADD SCTPPEER2EPGROUP ADD UPHOST2EPGROUP ADD UPPEER2EPGROUP ADD S1 ADD X2

Transmission Security

ADD VLANMAP SET DSCPMAP ADD VLANCLASS

ACL ACLRULE IKEPROPOSAL IKEPEER IPSECPROPOSAL IPSECPOLICY PSECBIND PACKETFILTER

Link ADD DEVIP ADD IPRT ADD SCTPLNK ADD CPBEARER ADD S1INTERFACE ADD X2INTERFACE ADD IPPATH(S1&X2) ADD ENODEBPATH

Digital CERTMK Certificate APPCERT TRUSTCE RT CROSSCE RT

ADD OMCH


Page59

30


Configuring Radio Data


Page60

Configure Sectors


Page61

31


Configure Cells


Page62

Configure Neighboring Cells


Page63

32


Summary

eNodeB commissioning Modes

Commissioning Preparations

The procedure of local commissioning through the USB Disk

The procedure of local commissioning through the LMT

The procedure of local commissioning through LMT with MML commands.


Page64

Thank you www.huawei.com

33

Microsoft PowerPoint - 02 OEB204700 eNodeB LTE V100R006 Local Commissioning ISSUE 1

Recommend Documents