Manual OXYGEN - Installation 1.1

ATRONIC OXYGEN™ Cabinet

Installation Manual

Rev. 1.1 April 2010

Release Ino ATRONIC OXYGEN™ Cabinet Installation Manual Rev. 1.1 Rel.: April 2010

Copyright Notice: © 2010, ATRONIC. All rights reserved. No part o this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language, in any orm or by any means, electronic, mechanical, magnetic, manual, or otherwise, or disclosed to third parties without the express written permission obtained rom a properly authorized ocial o ATRONIC. DISCLAIMER ATRONIC makes no representation or warranties, express or implied, with respect to this publication, or any product o ATRONIC, including but not limited to warranties o merchantability or tness or any particular purpose. ATRONIC reserves the right to make changes, enhancements, revisions and alterations o any kind to this publication or the product(s) it covers without obligation obligation to notiy any person, institution or organization o such changes, enhancements, revisions and alterations. TRADEMARKS This document document may may contain contain trademarks o ATRONIC. ATRONIC. All other brand and product names are trademarks or registered trademarks o their respective companies. OXYGEN™ - Installation Manual

2

Table o Contents 1. About this Manual.....................................................................................................4 1.1 Scope.................................................................................................................. 4 1.2 Target Audience.............................................................................................. 4 1.3 Included Sotware Releases ....................................................................... 4 1.4 Related Publications ..................................................................................... 5 2. Saety Instructions ....................................................................................................7 2.1 Saety Instructions - Electrical ................................................................... 7 2.2 Saety Instructions - Mechanical .............................................................. 8 2.3 Saety Instructions - Other.......................................................................... 8 2.4 Environmental................................................................................................. 8 3. Technical Data .............................................................................................................9 3.1 Specications .................................................................................................. 9 3.2 Dimensions ....................................................................................................10 3.3 Minimum Clearance ....................................................................................10 3.4 Footprint / Drill Pattern ..............................................................................11 3.5 Ergonomics ....................................................................................................12 4. Machine Components............................................................................................13 4.1 Cabinet Closed ..............................................................................................13 4.2 Main Door Opened ......................................................................................14 4.3 Belly Door Opened ......................................................................................15 4.4 Logic Box .........................................................................................................16 5. Machine Installation ..............................................................................................18 5.1 Inspect the Machines .................................................................................19 5.2 Machine Mounting ......................................................................................20 5.3 Install Top Light or Topper ........................................................................21 5.4 Replace Shipping Locks .............................................................................22 5.5 Prepare Coin Acceptor (MC-62) ..............................................................22 5.6 Check Cables and Connectors.................................................................22 5.7 Check Game Cards.......................................................................................22 5.8 Install Operator Specic Components .................................................23 5.9 Connect to Floor Network ........................................................................24 5.9.1 CRYSTAL.net™ ................................................................................24 5.9.2 CRYSTAL WEB™ ..............................................................................24 5.9.3 Non ATRONIC SMIBs ....................................................................24 5.9.4 System Connectors Pinout .......................................................25 6. Bringing into Service .............................................................................................26 6.1 Initial Power-up ............................................................................................26 6.2 Basic Setup .....................................................................................................27 7. Technical Support....................................................................................................28

OXYGEN™ - Installation Manual

3

1. About this Manual

1. About this Manual 1.1 Scope The OXYGEN™ Installation Manual describes how to install an ATRONIC OXYGEN™ gaming machine eaturing ATRONIC’s sensys EP™ electronic platorm. It describes how to mount the machine to a base and relevant procedures to be carried out beore the machine can be put into operation. Further it contains important saety instructions, technical data and cabinet drawings. Note: This document contains only procedural guideline or the OXYGEN™ cabinet. Each regulatory jurisdiction and gaming site have their own internal controls, policies and procedures that must be ollowed when accessing machines and setting conguration options. You are responsible or understanding and abiding by the rules that apply in your environment.

1.2 Target Audience Technical Personnel We address qualied technical personnel, who are involved in installation, setup and conguration o ATRONIC gaming machines. With this user group we assume that they are basically amiliar with gaming machines and casino related terminology. Please read this document and the contained saety instructions careully beore you start machine installation. Floor Personnel Further we address oor personnel that is allowed to open the machine‘s main door or maintenance purposes. Please read the contained saety instructions beore you open the main door.

1.3 Included Sotware Releases The installation procedures described in this manual do not relate to a certain sotware version.


4

1. About this Manual

1.4 Related Publications More detailed inormation about the OXYGEN™ cabinet, the sensys EP™ electronic platorm and the diversity™ multi-game sotware can be ound in the ollowing publications:

•

•

•

•

Sotware Manual Manual diversity™ Sotware (D.3.x.x STD)

Operating Manual Manual OXYGEN™ - Operating (D.3.x.x STD)

Peripherals (coin- and bill acceptors, hopper, etc.) -> See older “Peripherals” on the Service Manual CD.

Spare Parts Manual OXYGEN™ - Parts Catalogue

Note: All mentioned manuals can be ound on a CD-ROM titled “ATRONIC Service CD Manual 2010“ or www.atronic.com* I this manual did not came on this CD-ROM, please ask ATRONIC Technical Service or a ree copy o the latest revision. * to gain access an active Gamebook account is necessary.

Service Manual CD 2010 ENG v1.0


5

- blank page OXYGEN™ - Installation Manual

6

2. Saety Instructions

2. Saety Instructions Observe this safety instructions, to avoid per sonal injury or a possible damage to hardware, software, or data.

As this machine has to be opened or maintenance, rell and emptying, operators have to make sure the involved personnel takes note o this saety instructions.

2.1 Saety Instructions - Electrical Warning! Risk o Electric Shock Always switch of the machine and unplug the power cable beore servicing high voltage components. Be sure to ground this machine to prevent a current leak. ATRONIC makes no warranty as to the accidents (including ailures) caused by improper grounding. Do not expose the power cable to mechanical load such as contusion or tension. Damaged power cables can lead to re or shortcuts. Use the specied uses only. I the specied uses easily blow out, please consult ATRONIC Technical Services. Always switch of the machine beore removing or servicing electronic components and beore connecting/disconnecting a connector. Check that all connectors are seated correctly. False connections can cause irreparable damage, not covered by warranty. Always take precautions against electrostatic discharges (ESD) when handling circuit boards. Wear a grounded wrist strap and avoid placing circuit boards on static generating suraces as carpet or upholstered chairs.

continued on next page... OXYGEN™ - Installation Manual

7

2. Saety Instructions

2.2 Saety Instructions - Mechanical Warning! Tip Hazard! To avoid personal injury, the OXYGEN cabinet must be securely attached to the base, and the base must be securely attached to the oor or wall. See also section 5.2 Installation / Machine Mounting. Do not install the machine on unstable oor. The machine is heavy. Always use appropriate equipment or transportation and installation. Caution! Moving Parts Make sure to disable the hopper, when working on it.

2.3 Saety Instructions - Other Only qualied personnel can assemble, install, maintain, inspect, and troubleshoot the machine. Use only original ATRONIC parts or replacement. Do not use chemical duster, thinner, benzine, alcohol, or synthetic detergent or cleaning the machine. They can damage the surace o the machine. Please reer to relevant ATRONIC service manuals or urther instructions on setup, operation and maintenance.

2.4 Environmental Adhere to the environmental specications stated in section 3. Technical Data (next page). Do not install this machine outdoors, or in areas with large variation in temperature or excessive dust pollution. The machine may only be installed or operated in dry conditions. The machine must not be cleaned using a high pressure cleaner or a vapor jet and must not be installed or operated in areas where high pressure cleaners or vapor jets are used. I the machine was exposed to low temperatures, do not power on the machine until it has acclimatized to ambient temperature and no condensing is present. OXYGEN™ - Installation Manual

8

3. Technical Data

3. Technical Data 3.1 Specifcations Manuacturer:

ATRONIC Austria GmbH Seering 13 - 14 A-8141 Unterpremstaetten

Model:

SEPOXG / OXYGEN

Dimensions in mm: (max. w/h/d)

613 / 1520 / 590 (w/o topper)

Weight:

97 kg (coin-less) 104 kg (coin-on)

Electrical Specifcation Required Voltage:

100V to 240V AC 50Hz / 60Hz

Use earthed power outlet rated min. 8A / 115V, 4A / 230V. Power Consumption Idle Mode:

1,9A / 115V, 0,8A / 230V

Payout Mode:

2,4A / 115V,

1,2A / 230V

Max. Power: 450 Watt (without internal power outlets) Power Supply Secondary Voltage:

Fuses Main Fuse: Peripheral Board: (secondary voltages)

+24V / 5A; +12V / 17A; - 12V / 0,5A; +5V / 20A; +3.3V / 7A (all glas uses 5 x 20mm) T5A / 250V F100 (+5 V0) = T 5A F102 (+12 VP_1) = T 5A F103 (+12 VP_2) = T 5A F104 (+12 VP_3) = T 5A F105 (+12 VP_4) = T 5A F107 (+24 V) = T 4A

F100

F102

F107

F104

F105

F103

Secondary voltage uses on the Peripheral Board

Environmental Specifcations Operating Temperature: 0°C - 45°C (32°F - 113°F) Operating Humidity: 0% to 85% (non condensing)


9

3. Technical Data

3.2 Dimensions

) m m ( 0 2 5 1

0 9 3 1

510 560 613

348 492 590

3.3 Minimum Clearance •

EachOXYGEN™machineshouldhavea minimumbasewidthof 720mm,tofullyopenthemain door without touching the adjacent machine. This translates to a minimum space clearance o 210 mm between two OXYGEN™ machines (body side to body side).

•

Leaveaminimumspaceclearanceof245mmtoawall(bodysidetowall). 720 245


720 210

10

3. Technical Data

3.4 Footprint / Drill Pattern

(105)*

(105)*

330

* This dimension depends on the base width

* This dimension depends on the base width

223 67

5 , 7 6

REAR OF CABINET

7 3

7 5

Ø 12 mm (4x)

) m m (

5 , 8 2 2

CABLE DROP Ø 64mm

5 , 1 7 2

5 , 6 9 2

5 , 6 3 3

COIN DROP Ø 80mm DRILL PATTERN OXYGEN™ CABINET

67 297 ATRONIC STANDARD BASE (720mm)

302,5 510

(720)*


11

3.5 Ergonomics The OXYGEN™ cabinet is designed to provide a maximum o playing comort. For an optimal seating and playing comort, the diference between the base height and the seating height should be approximately 150 mm. Based on a 1,75 m tall player this results in •

thenaturallineofsightisdirectedtowardsthecenterofthemainmonitor

•

thearmsarepositionedinparalleltotheoorandsupportedbythearmrests

•

thelegsareinacomfortable90°angle

m m 0 5 1

Examples: Height o available base is 24” / 60 cm --> use chair height 75 cm Height o available base is 18” / 45 cm --> use chair height 60 cm Height o available chair is 65 cm --> use 18” / 45 cm bases


12

4. Machine Components

4. Machine Components 4.1 Cabinet Closed Top Light

Topper

Top Box

Upper Loudspeakers

Upper Monitor Main Monitor

Air Outlet

JACKPOT Key Switch AUDIT Key Switch Mechanical Meters

Player Tracking Area (here with Card Reader) Loudspeaker

Main Door Lock(s)

Ticket Outlet Coin In

Main Door Release

BET - Button BET + Button

CALL ATTENDANT Button

START / TAKE WIN Button

CASH OUT Button Name Plate Bill In

AUTOPLAY Button MENU Button GAMBLE Button

Belly Door Release / Belly Door Lock

START / TAKE WIN Button Coin Bowl


13


4.2 Main Door Opened

Top Box

Top Box Release Logic Box Logic Box Lock Card Slot Cover Peripheral Board Main Door Switch Mounting Bracket or additional Equipment Main Door Lock(s) Ticket Printer

Main Door Release Bill Acceptor

Power Outlets Power Switch Power Supply

Hopper Board Hopper

Bill Door Lock Bill Door

Sub Wooer

Cable Drop Hole Coin Drop Hole


14


4.3 Belly Door Opened

Coin In - LED Board Belly Door Switch Coin Acceptor Coin Channels Diverter Solenoid Pneumatic Spring

Coin In / Ticket Outlet


Bill In - LED Board Belly Door Lock / Belly Door Release Bill Door Lock Bill Door

Bill In

15


4.4 Logic Box

Figure shows logic box with the card slot cover removed

Fan (Air Outlet)

Peripheral Board Connectors

HDMI Video Out (Upper) HDMI Video Out (Main)

Logic Box Cover Release

Game Smart Card Game Compact Flash Card

Logic Box Switch Audio Line In USB Ports LAN Port 1 LAN Port 2 (not used) VGA (not used) COM2 COM1 (GAT Port) HDMI Audio Out

Power Supply Connector


16

- blank page OXYGEN™ - Installation Manual

17

5. Machine Installation

5. Machine Installation This section should only be carried out by qualifed service personnel. Review the list below and perorm as needed. Explanations are located on the ollowing pages and in additional manuals. Inspect machines or transport damage. Any transport damage should be noted and witnessed by the reight orwarder. The manuacturer accepts no responsibility or transport damage.

Note: Depending on machine conguration or jurisdictional requirements, additional tasks may have to be carried out beore the machine can be put into operation (e.g. acceptance inspection, logic box sealing, etc.).

Check machines or the correct hardware conguration. Prepare the stand by drilling the mounting holes, cable drop and coin drop (i necessary). Mount the machine to the base. Install top light or topper Replace shipping locks with casino specic locks. Prepare the coin acceptor and the hopper. Check that cables and connectors are seated correctly. Check that the game cards are seated correctly. Install operator specic components Connect to the oor network (i applicable) Apply power to the machine. Load paper into the printer (i available). Execute basic machine setup, i necessary (RAM Clear, Initial Setup and Jackpot Conguration). Congure game (Service Menu / Settings). Test bill and coin handling (Service Menu / Diagnostics).


18


5.1 Inspect the Machines (a) Unpack the machines and inspect them or transport damage. Any transport damage should be noted and witnessed by the reight orwarder. The manuacturer accepts no responsibility or transport damage. (b) Check the machines or the correct hardware conguration (bill acceptor, coin acceptor, hopper, and printer type)


19


5.2 Machine Mounting Warning! Tip Hazard! To avoid personal injury, the OXYGEN™ cabinet must be securely attached to the base using all our mounting bolts, and the base must be securely attached to the foor or wall. 1. Obtain a suitable stand upon which to install the OXYGEN™. The drill pattern and the recommended minimum clearance to the adjacent machines are provided in section 3.4 Technical Data / Footprint/Drill Pattern.

(105)*

330

* This dimension dependsonthe basewidth

(105)* * This dimension dependsonthe basewidth

223 67

5 , 7 6

REAR OF CABINET

7 3

7 5

Ø 12 mm (4x)

) m m ( 5 , 1 7 2

5 , 8 2 2

CABLE DROP Ø 64mm

5 , 6 9 2

5 , 6 3 3

COIN DROP Ø 80mm DRILL PATTERN OXYGEN™ CABINET

67 297

2. Drill our mounting holes and a cable hole in the top o the base. I the machine will be using a coin drop bucket inside the stand, then a coin drop hole must also be cut.

ATRONIC STANDARD BASE (720mm)

302,5 510

(720)*

3. Place the machine on the base. Caution! The machine is heavy. Use a lit truck to transport and lit the machine. Never use the arm rest to lit the machine! I no lit truck is available, use the recessed grip at the lower side o the coin bowl to lit the machine. Do not use the arm rest to lit or carry the machine.

Recessed Grips

4. Place the machine so that the holes on the bottom o the machine are aligned with the holes on the base. You have to remove the hopper (i installed) and the coin drop plastic rame to get access to the mounting holes. Warning! Hand or Head Injury! The main door can slam closed, when the machine is moved jerkily.

5. Insert all our mounting bolts through the bottom o the machine. Place a washer and nut on each o the our bolts inside the base and tighten them. Ensure that no wires are trapped when the bolts are tightened. Ensure that the machine is securely attached to the base, and that the base is securely attached to the oor or wall. 6. Install the hopper and the coin drop rame, i previously removed.


20

5.3 Install Top Light or Topper To install the top light or the topper 1. Open the main door and press the top box release upwards to open the top box door.

Top Box Release

2. Unasten, unplug and remove the upper monitor. Note: When removing the monitor, make sure to lay it down with the ront side acing upwards, to avoid scratches in the monitor surace.

3. (a) Mount the top light and connect the top light signal and the top light earthing cable. (b) Mount the topper and connect the topper signal and the topper earthing cable.

4. Re-install the upper monitor, asten it with our srews and close the top box.


21


5.4 Replace Shipping Locks (1) (2) (3)

I not ordered otherwise, ATRONIC machines are equipped with shipping locks or easy start-up. These locks have to be replaced by casino specic locks to provide appropriate security. (1) Jackpot Key Switch (2) Audit Key Switch (3) Logic Box Lock (4) Main Door Lock (5) Belly Door Lock (6) Bill Door Lock / Stacker Locks

(4) (5) (6)

5.5 Prepare Coin Acceptor (MC-62) •

Slide holder or reerence coin rightwards, remove (plastic) transport chip and replace it with appropriate reerence coin.

•

Check the reerence coin or proper (parallel) seating.

-> See manuals Peripherals / Coin Acceptor or details.

5.6 Check Cables and Connectors Check that all connectors are seated correctly, prior to initial power up. Important: False or loose connections can cause irreparable damage, not covered by warranty.

5.7 Check Game Cards Make sure that the Platorm Smart Card (1), the Game Smart Card (2) and the Game CF Card (3) are seated correctly, prior to initial power up. The cards may loose connection during transportation.

(1)

(3) (2)


22


5.8 Install Operator Specifc Components Install the operator specic components such as SMIB (Slot Machine Interace Board), ber optics board, etc., and player tracking components (i applicable). The OXYGEN™ cabinet provides a mounting bracket to install additional components (g. A).

(fg. A): Mounting area or additional components

Player tracking components are installed on customized player tracking brackets (g. B). These brackets are usually supplied by your player tracking components manuacturer. Please reer to the relevant mounting instructions that came with the bracket and the player tracking components.

(fg. B): Player tracking bracket


23


5.9 Connect to Floor Network 5.9.1 CRYSTAL.net™ A OXYGEN™ machine congured or CRYSTAL.net™ communications will have a CRYSTAL Module (CMOD) installed. Connect the CMODs Ethernet port 1 to the CRYSTAL Base Socket (CBSO) which is usually installed in the machine base. See ATRONIC SYSTEMS / CRYSTAL.net™ Technical Manual or details.

5.9.2 CRYSTAL WEB™ A OXYGEN™ machine congured or CRYSTAL WEB™ communications will have a Machine Data Controller (MDC) and a Earth Print (EP) installed. Connect the Earth Print to the Base Socket (BSO) which is usually installed in the machine base. See ATRONIC SYSTEMS / CRYSTAL WEB™ Technical Manual or details.

5.9.3 Non ATRONIC SMIBs Operator specic Slot Machine Interace Boards (SMIB) have to be connected to the Peripheral Board. The Peripheral Board provides three RS232 serial ports to communicate with the SMIB. The three serial ports correspond to SAS channels 1, 2 and 3. The connector or SAS channel 1 (accounting channel) also incorporates the door contacts and is thereore split into two connectors. The connectors or SAS channels 2 and 3 provide serial communication only.

SAS2 SAS3

Accounting (SAS1)

See next page or a connectors pinout.


24


5.9.4 System Connectors Pinout The accounting system connection (SAS channel 1) is split into two connectors P220 and P221.

Accounting System (Peripheral Board P220) 1 2 3 4 5 6 7 8 9 10 11 12 13 14

1

14

Accounting System (Peripheral Board P221) 1 2 3 4 5 6 7 8 9 10 11 12

+5V +12V COM 0 / RS232 RxD COM 0 / RS232 TxD Main Door - Normally Close Main Door - Common Main Door - Normally Open Bill Door - Normally Close Bill Door - Common Bill Door - Normally Open Logic Door - Normally Close Logic Door - Common Logic Door - Normally Open Ground

Recommended Connector: Molex 22-01-3147, Crimp Terminal 08-52-0123 or Tyco 1-770602-4, Crimp Terminal 770666-1

1

12

Belly Door - Normally Close Belly Door - Common Belly Door - Normally Open Drop Door - Normally Close Drop Door - Common Drop Door - Normally Open Bill Stacker - Normally Close Bill Stacker - Common Bill Stacker - Normally Open NC NC NC

Recommended Connector: Molex 22-01-3127, Crimp Terminal 08-52-0123 or Tyco 1-770602-2, Crimp Terminal 770666-1

The connections or SAS channels 2 and 3 come as a D-Sub 9 male connector (serial connector).

SAS Channel 3 (Peripheral Board P210) 1 2 3 4 5 6 7 8 9

NC COM 4 / RS232 RxD COM 4 / RS232 TxD +5V Ground NC +12V NC NC


6 1

SAS Channel 2 (Peripheral Board P206) 1 2 3 4 5 6 7 8 9

6 1

NC COM 1 / RS232 RxD COM 1 / RS232 TxD +5V Ground NC +12V NC NC

25

6. Bringing into Service

6. Bringing into Service 6.1 Initial Power-up Caution: I the machine was exposed to low temperatures, do not power on the machine until it has acclimatized to ambient temperature and no condensation is present. 1. Make sure that the power cable has not been damaged during transport. 2. a) Route the power cable through the cable drop hole in the bottom plate o the machine into the machine base. b) I you want to use the cable access hole at the back o the cabinet, rst remove the hopper to get access to the cable access cover. Then remove the ully closed cover and replace it by a cover with cable recesses. 3. Make sure that the power outlet is grounded, in good condition and not showing any signs o overheating or damage. Then connect the power cable to the power outlet. 4. With the main door open, turn the power switch to the “ON” position. The power up cycle will take some minutes, because the machine checks the installed hardware, the circuits boards rmware and security relevant circuits. 5. Check the voltage LEDs next to the corresponding uses on the Peripheral Board. The LED‘s should all be lit.

Proceed with the Basic Setup, as required. (RAM Clear, Initial Setup and Service Menu settings) For inormation on conguring the machine’s settings, reer to the Sotware Manual or a particular sotware version (e.g. Sotware Manual - diversity™ - (D3.0.x)) or urther details.


26

6. Bringing into Service

6.2 Basic Setup ATRONIC machines usually come congured as specied during order processing. However it might be necessary to recongure basic machine settings, such as denomination, metering, paytable, validation mode, etc. These settings can not be altered during normal operation, as they require a machine re-initialization or technical or jurisdictional reasons.

1. Carry out a RAM Clear I required, carry out a critical data storage ormatting using the RAM Clear Smart Card. This will clear all machine data, statistics and settings, including progressive jackpot conguration and allows or reconguration. 2. Carry out the Initial Setup Ater a RAM Clear the machine automatically enters the Initial Setup menu. The Initial Setup allows to congure basic machine setting.

Note: For inormation on conguring the machine’s settings, reer to the Sotware Manual or a particular sotware version (e.g. Sotware Manual - diversity™ - (D3.0.x)) or urther details.

3. Adjust game settings in the Service Menu Enter the Service Menu to adjust operator selectable game settings, such as money limits, game volume To enter the Service Menu turn the Audit Key with the main door open. 4. Test Money Handling Select Diagnostics rom within the Service Menu and carry out the required tests. 5. Test Communication Close the main door to switch to operation mode and test the communication to the accounting system.

Note: Ater money handling and communication tests you may want to carry out another RAM Clear to reset the machine statistics.


27

7. Technical Support

7. Technical Support ATRONIC ofers and provides technical support 24 hours a day, 7 days a week. I technical assistance is required during normal business hours, please contact your local technical services representative at one o the numbers below. Technical Support Locations: ATRONIC Germany (International Headquarter) ATRONIC Peru

(+49) (+51)

5741 24099 950 161 832 00

I technical assistance is required outside o normal business hours, please contact the ATRONIC Technical Hotline number below. ATRONIC Technical Hotline: For technical assistance in Europe, South Arica, Asia, Central and South America outside o normal business hours:


(+49)

5741 24099 999

28

Manual OXYGEN - Installation 1.1

Recommend Documents