Wind load computations NSCP 2010 lowrise with portal method
Full description
Loads on Canopy to be adoptedFull description
Full description
Full description
Load Calculations.pdfFull description
load calculationsFull description
Full description
ddd
AFull description
ddd
Full description
POLINESFull description
Praktikum PSSDeskripsi lengkap
Deskripsi lengkap
Service Training August 1998
INTRODUCTION TO LOAD SENSING/PRESSURE COMPENSATED HYDRAULIC SYSTEMS
LOAD SENSING / PRESSURE COMPENSATION PUMP CONTROL VALVE
LOAD
ENGINE
VARIABLE DISPLACEMENT PUMP
DOUBLE CHECK VALVE
50 PSI SPRING
PRESSURE REDUCING VALVE
CLOSED CENTER CONTROL VALVE
INSTRUCTOR GUIDE
-2-
Instructor Materials
8/98
COURSE DESCRIPTION Introduction to Load Sensing / Compensated Hydraulics Course Length: 1/2 Day Class size: 8 students maximum CONTENT
WHO SHOULD ATTEND: • Training Instructors • Technical Communicators • Product Support Engineers • Service Technicians This module of course explains a typical basic hydraulic system and builds it step-by-step into a Load Sensing / Pressure Compensated hydraulic system. Participants will learn about the advantages and disadvantages of a basic system versus a LS/PC system. A student handbook and quiz is provided to assist the students in learning the concepts of LS/PC. Students will be challenged to determine what happens as load and flow requirements change to the systems covered. This is a classroom based program and is normally taught as part of the hydraulic system training for a particular machine This module can stand a lone, but for better retention of the information refer to materials in the BCP Backhoe Loader Systems Course for various in the iron type exercises. COURSE PRE-REQUISITES Prerequisite tests should be administered at least one to two weeks before students take the course. Students should pass the following pretests with 90% or better. • Successfully passed the Basic ISO Pre-test VEBV0556 • Successfully passed the Basic Hydraulic Pretest VEBV0557 Prerequisite courses should be completed prior to participating in this course. • Multimedia Course "Fundamentals of Mobile Hydraulics" TECD9001
-3-
Instructor Materials
8/98
PREPARATION CHECKLIST Prior to conducting the training session, gather the following materials: Service Training Meeting Guides STMG 595 "Introduction to Load Sensing Pressure Compensated Hydraulic Systems" SESV1595 Video Tapes "Introduction to LS/PC Hydraulics Systems"
SEVN1804
Miscellaneous - for Reference only "Introduction to LS/PC Hydraulics Systems" SEEV0540 "Introduction to Variable Displacement Pumps and Controls in LS/PC Hydraulics" SEEV0541 "Introduction to Pressure Compensated Valves in LS/PC Hydraulics" SEEV0542 "Introduction to 416-446 Backhoe Loader Hydraulics"SEEV0543 "Introduction to Variable Displacement Pumps and Controls in LS/PC Hydraulics" SEVN1837 "Introduction to Pressure Compensated Valves in LS/PC Hydraulics" SEVN1900 "Introduction to 416-446 Backhoe Loaders - LS/PC Hydraulics" SEVN1988
STUDENT LITERATURE CHECKLIST Description Form No. "Introduction to Load Sensing Pressure Compensated Hydraulic Systems" Student Handbook
MEDIA CHECKLIST SESV1595: 1-13 SESV1595: 14 & 15 are optional
MODULE: INTRODUCTION TO LOAD SENSING PRESSURE COMPENSATED HYDRAULICS This module is a review of basic "load sensing/pressure compensated" hydraulics.
OBJECTIVES
❑ ❑
1. On a quiz in the back of the Student Handbook, identify system characteristics of Load Sensing and Pressure Compensation and components used in this type of hydraulic system. 2. On a quiz in the back of the Student Handbook, determine system pressures and pressure differences at various locations on provided quiz schematics.
• LS/PC system review - These slides review the basic principles of load sensing and pressure compensation - Provide students with copies of the LS/PC Student Handout - The last three pages of the handout has a quiz, which the student must complete.
SHOW SLIDES: SESV1595: 1 - 13 Approx. Time: 2 hours
ADMINISTER QUIZ Approx. Time: 2 hours
• (Optional) LS/PC system review using a Video - The LS/PC Introduction Video may be used in place of the slides to complement the instructor's knowledge.
• Review Quiz
-6-
Instructor Materials
8/98
LS/PC QUIZ ANSWERS
I. Match the following:
II. True/False.
1. A
A. F "closed"
2. E
B. T
3. D
C. T
4. B
D. T
5. C
E. F "double check valve"
III. Fill in the correct response. System pressure will be: 1800 psi + 300 psi = 2100 psi Valve A work port pressure = 1800 psi
∆ P across pressure reducing valve = 2100 psi - 1890 psi = ∆ P across control spool = 1890 psi -
1800 psi =
90
210
psi
1340
psi
psi
Valve B work port pressure = 700 psi
∆ P across pressure reducing valve = 2100 psi - 760 psi = ∆ P across control spool= 760 psi -
700 psi =
60
psi
IV. Fill in the correct response. System pressure will be:
3000
psi +
0
psi =
3000
psi
Valve A work port pressure = 3000 psi
∆ P across pressure reducing valve = 3000 psi - 3000 psi = ∆ P across control spool = 3000 psi - 3000 psi =
0
0
psi
psi
Valve B work port pressure = 1000 psi
∆ P across pressure reducing valve = 3000 psi ∆ P across control spool= 1060 psi -
