KONE Error Code Failure Reason

KONE error code Failure reason

KONE error code ( full version ) Failure reason code 0001 driver long time after a period of the position signal 30/B30 running time does not change. Immediately stop power off 0004 three consecutive synchronous operation faile d. Three consecutive synchronous operation of the system are not receiving proper leveling signal slowdown after three failed to stop at the end of the station . Off power 0007 Area 308,030 switch stuck after the start time is not detected falling edge 30/B30 signal. Door zone has been effective operation of the switch t o the destination 30/B30 0008 NVRAM damaged or capacity is not enough when the power transmission capacity is not enough to detect NVRAM . Replace NVRAM 0014 Area check the circuit did not release any of two consecutive .486.443.1.443:2 .486.443.1.443:2 without (ACO / ACL) run to the destination floor , shut off electri cal service 0015 Area check circuit does not pull any one .486.443.1.443:2 consecutive times wit hout (ACO / ACL) run to the destination floor , shut off electri cal service 0021 safety circuit fails . Safety Safet y circuit input a no voltage is immediately stopped. Safety circuit switched 0022 Hall door barrier. 3 no-voltage input safety circuit stop immediately . Hall door turns 0023 car door lock will not work. Safety circuit voltage input 2 no stop immediately . Door sedan turned 0025 start of system failure when the elevator did not stop the main contactor release does not start . Main contactor failure row 0026 drive system failure . Driven system detects a fault (v3FCK not light ) does not start. Off power or play overhaul 0039 shorted 77 buttons stuck. Shorted 77 buttons card refuses to start sta rt LCEBOPU board. Until the release button 0042 car lighting monitor lighting no electricity to run the car to the destination floor. From service until the signal disappears 0044 closed barrier several attempts . Closed door barrier five times but failed . Door opening does not go off electricity or playing back door opener repair 0048 remain valid reverse signal lasts more than one minute to open the door to keep the door closed until the signal disappears electricity 0051 start start invalid 5 times unsuccessful , such as landing door may not shut the door and then try five automatic recovery 0052 down synchronous switching while effectively .77 U and 77N while effectively effectivel y stop immediately. RDF can only start at the end of the s tation automatically restored 0058 ready to run out. Had requested but the elevator did not start running more than 100 seconds to stop immediately. Attempt to run off after ten seconds or playing electric acceleration signal 0060V3F16 overhaul did not receive accelerated loss of signal -to-end operation of the drive system power off or play station overhaul 0071 district loss of signal . After several layers 61U / N when the rising edge of the signal can not be found 30/B30 run to the destination floor. Door shut without electricity or playing overhaul 0072 61U Signal stuck .61 U signal after leaving the gate area is still not released for some time to run to the destination floor. Then open to the lowest floor as still stuck, then shut off electrical service or repair 0071 hit area through several layers of signal loss 61U / N can not  be found when the rising edge edge of the signal to run 30/B30 destination destination floor . door shut without electricity or playing overhaul

0073 61N signal stuck. Passes through several layers of the door area. 61N can not find the rising edge of the signal . Off electricity or playing overhaul 0073 61N signal stuck. Passes through several layers of the door area. 61N can not find t he rising edge of the signal . Off electricity or playing overhaul 0074 61N signal stuck .61 N signal after leaving the gate area for s ome time still not released. Off power or play overhaul 0075 61U Signal stuck. Passes through several layers of the door area. 61U can not find the rising edge of the signal . Off electricity or playing overhaul Automatic recovery after the 0076 area surveillance for the first time not to release without releasing (ADO / ACL) ( allowed ) to run to the destination floor 15 seconds 486.443:1.443:2 any runtime 0077 open limit fault ( been ineffective ) . Door open , but can not re ceive a signal Button stuck in the 0078 car . Buttons stuck inside any car more than 60 seconds to cancel the twist service until button to return to normal 0079 Outbound button stuck. Arbitrary outbound button stuck more than 60 seconds to cancel the twisted services back to normal until the button Monitor automatically restored 0082 area does not pull no first pull (ADO / ACL) ( allowed ) to run to the destination floor 15 seconds after running either 486.443:1.443:2 0083 to calculate the position of losing the signal does not match with the wells run to the end station 0084 open limit fault ( been effectively ) shut the door open but still received signal 0089 Hall landing door locks open circuit monitoring ( non- car position ) run to the destination floor . Shut off electrical service se rvice or overhaul fight 0145 EBD EBD equipment damage 0146 EBD EBD battery cell damage Drive failure 0101 drivers to stop driving the system detects a fault the elevator stopped to check the drive shaft failure 0102 motor overcurrent 0103 braking resistor braking resistor is damaged, check the brake resistor 0104 motor overheated motor thermistor 0105 AC power supply intermediate DC voltage is too low 0106 V3F bad 0107 load bearing device failure signal voltage is less than 0.6V regulator load device 0108 motor / tachometer speed reverse polarity wrong / bad car balanc e / load allowed / not open brake / drive parameters right / overspeed 0109 Position location is lost is lost drive system under investigation deceleration , leveling switch 0110 radiator overheating. Overheating radiator driver module The drive control process failures 0111 deck 61: N at 61: Under U 61U / N swapped Chapin layer switching sequence 0112 61: U / N overlapping layer switch position too Chapin 0113 simultaneous switching error error synchronous switch synchronous switch synchronous switch failure investigation 0114 floor distance is too short to check the position of the magnet 0115 the proportion of errors 0116 test runs to learn counting error floor redone floors unsuccessful learning  Network failure A side door / 3 side

1101 bad circuit board input board is damaged, electrical wiring errors can not be contacted or not normal deceleration stop layer , close contact does not move again until the 1202 / 2201 first board fault circuit board is damaged , electrical wiring errors can not be contacted or did not resume normal service until the single staircase contacted again 1202 / 2202 second board fault circuit board is damaged , electrical wir ing errors can not be contacted or did not resume normal service until the single staircase contacted again 1203 / 2203 The third board fault circuit board is damaged , electrical wiring errors can not  be contacted or did not resume normal service until the single staircase contacted again 1301 / 2301 output boards bad circuit board is damaged, electrical wiring errors can not be contacted or did not reach the target layer , the door does not move again until the contact 1401 / 2401 first board fault circuit board is damaged , electrical wiring errors can not be contacted or did not resume normal service operation signal is detected by the first xx 14xx/24xx boards fault circuit board is damaged , electrical wiring errors c an not be contacted or did not resume normal service operation signal detection by 1501 / 2501 first board fault circuit board is damaged , electrical wiring errors can not be contacted or did not resume normal service operation signal is detected by 15xx/25xx first xx boards fault circuit board is damaged , electrical wiring errors can not be contacted or did not resume normal service operation signal is detected by 1601 bad circuit board expansion board is damaged, electrical wiring errors can not be contacted or did not resume normal service until the single staircase contact again on 1701 / 2701 first board fault circuit board is damaged , faulty wiring or no power can not be contacted again until contact on 17xx/27xx first xx boards fault circuit board is damaged , faulty wiring or no power can not  be contacted again until contact on