Sharp 2014 Code A1 A2 C1 C2 C3 E1 E3 EE-EL EE-EU J0 J1 J3 J7 J8 L6 U1 U2 U3 U4-01 U4-02 U4-03 U5 U6 U7 U8 U9
Description Jam in document feeder Jam in document feeder Cassette misfeed Cassette feed, bypass unplugged Bypass misfeed Paper feed jam Exit jam Developer overtoned during setup Developer undertoned during setup Developer setup taking place Add toner Drum unit not installed properly or missing Drum unit due for replacing Wrong drum unit or power was turned on after J7 displayed Key counter or other optional counter accessory problem Drive problem Scan Lens Fuser thermistor High fuser temperature Low fuser temperature 500 sheet cassette lift motor Main board problem Document glass too hot (with document feeder) Problem with line voltage Auto developer setup problem
Sharp 2020 Code Description CC Original detection problem CH Lit Steadily: Sorter not installed, or not turned on CH Flashing: DV unit not installed, not connected
F1
F2 H2 H3 H4 L1 L3 L4 L5 L8 P PC U2 U4 U5
properly, or not latched in place properly Sub code 00: Communication error between main board and sorter. Sub code 02: Sorter transport motor drive. Sub code 31: Image density sensor. Could be a problem with light level. Sub code 32: Drum mark sensor problem. . Does not see mark on drum or sensor not working properly. Sub code 00: Fuser thermistor open. Sub code 00: Fuser temperature too high. Sub code 00: Fuser temperature too low. Lamp, thermal switch, connections. Scan forward problem. Motor, sensor, board Scan forward problem. Motor, sensor, board. Drive problem; main motor, gear, sensor, bind. Lens problem. Motor sensor board. Sub code 01: Zero cross. Paper feed problem or no paper Card counter not installed Sub code 01: Memory loss. Sub code 00: Communication problem between copier and duplex unit. Sub code 00: Communication problem between main board and ADF.
Sharp 2022, 2027, 2035 Code P10 P11 P13 P14 P16 P18 P19 P20 P21 P22
Description Set or clear departmental counter Display individual departmental counts Clear departmental counters Enter, clear or change department numbers Change max. number of copies that can be run Sends alarm if the wrong department number is tried three times in a row Change code number Adjust auto exposure Adjust automautic shufoff Adjust manual exposure
P23 P24 P25 P26 P27 P28 P29 P30 P45 P70 P71 P72 P73 P74 P75 P76 P77 P90
Adjust auto clear time Set up fixed magnification settings Set maximum number of copies or of sets Binding margin Border erase setting Defaults at power on Display various counts Auto repeat on or off Message display time Auto paper select on or off Auto cassette select on or off Maximum copies in duplex Copy condition in rewrite Duplex limit when problems with duplex unit Prevent auto duplex Prevent stapling Prevent cover use List programs
Sharp 2025, 2030, 2040 Cod e C2 CC CH F1
F2
F3 H2 H3
Description Transfer corona problem or HVT Original detection problem. Door open or developer unit not installed, not connected properly, or not latched in place properly. Sub code 00: Communication error between main board and sorter. 01: Jogger error. 02: Sorter transport motor drive. 04: Sorter bin sensor problem. Lower limit sensed wrong. Sub code 02: Toner motor problem. 31: Image density sensor problem. Could be a problem with the light level. 32: Drum mark sensor problem. Does not see mark on drum or sensor does not work properly. 35: Grid voltage correction will not work during simulation. Sub code 12: Copier upper cassette lift motor problem. Copier bottom cassette lift motor problem. Fuser thermistor open. Fuser temperature too high.
H4 Fuser temperature too low. Lamp, thermal switch, connections. L4 Sub code 01: Drive problem, main motor, sensor, bind. Sub code 03: Drive problem with 4th/5th mirror assembly, L5 motor, sensor, board. L8 Sub code 01: Power frequency problem. PC Card counter or key counter not installed. There is an inhibit command from the PC modem. This is reset PF with simulation 17. U2 Sub code 00 or 01: Memory error. Sub code 20: Mirror motor locked. 21: Mirror motor home U3 sensor. Sub code 02: Duplex alignment plate out of position motor, U4 cable, sensor. Sub code 00: Communication problem between main board and U5 RADF. 01: RADF motor drive problem. 02: RADF motor drive problem. 03: RADF resist sensor. 04: RADF exit sensor. Sub code 00: Communication error between copier and desk. 01, 02, 03: Desk lift motor drive problem. 08: Desk 24v U6 problem. 09: LCT motor overload. 10: Desk transport motor drive problem. Sub code 00: Communication problem between copier and PC U7 modem.
Sharp 2050 Code CC-nn CH CH EE-EL EE-EU F1-00 F1-02 F1-03 F1-04 F1-05 F1-06
Description Original sensing problem Lit steadily: Door open Flashing: Developer unit not installed, not latched or not installed properly During developer calibration, overtoned condition detected During developer calibration, undertoned condition detected Communication problem between main board and stapler Stapler sorter transport drive problem Problem with guide bar oscillator motor Index lower sensor Index upper sensor Shift motor problem in stapler sorter, or index motor
F1-08 F1-10 F2-00 F2-31 F2-32 F2-33 F2-35 F2-37 F3-01 F3-02 F3-03 F3-12 F3-22 F3-32 F3-42 H2-00 H3-00 H4-00 L1-00 L2-00 L3-00 L4-01 L4-02 L5-00 L8-01 L8-02 L8-03 P20 P21 P22 P25 P26 P28 P29 P70 P72 P74 P75
problem Staple sorter shift motor drive problem Stapler problem Toner sensor problem Drum surface reflecting problem Drum sensor not scanning mark properly Grid voltage is too high or too low During patch detection, measurement is wrong Drum mark sensor adjustment problem LCT encoder LCT lift problem LCT down problem Cassette 1 lift problem Cassette 2 lift problem Cassette 3 lift problem Cassette 4 lift problem Fuser thermistor Fuser temperature too high Fuser temperature too low Scan problem Mirror motor drive problem Scan return problem Drum motor drive problem Main motor drive problem 4/5 mirror drive problem Full wave signal missing to auto exposure Full wave signal to auto exposure is incorrect During auto exposure adjust procedure, the auto exp. Adjust automatic exposure Auto shut off timing Toner save mode Maximum number of copies that can be selected Margin shift Initial status To read total copies Auto paper select Bypass in duplex Stop document feeder use Stop duplex use
P76 P83 P90 PC PF U0-00 U2-00 U3-00 U3-20 U3-21 U3-26 U3-41 U3-42 U4-02 U4-03 U5-00 U5-01 U5-02 U5-03 U5-04 U5-11 U5-12 U7-00
Stop stapler use Modem access to codes through phone line Display all of the operator programs Card counter Modem problem Operation panel problem EEPROM error. Reset with sim. 16 Communication problem between master and mirror controller Mirror drive problem Mirror home sensor problem Mirror motor voltage problem Lens motor home correction did not go well 4/5 mirror motor problem similar to U3 -41 Duplex alignment plate sensor Duplex rear plate sensor Communication problem between RADF and copier RADF resist sensor RADF reverse sensor RADF timing sensor RADF empty sensor RADF paper feed drive problem RADF transport drive problem Communication problem between copier and modem
Sharp 2114 Code A1 A2 C1 C2 C3 E1 E3 EE-EL EE-EU J0
Description Jam in document feeder Jam in document feeder Cassette misfeed Cassette feed, bypass unplugged Bypass misfeed Paper feed jam Exit jam Developer overtoned during setup Developer undertoned during setup Developer setup taking place
J1 J3 J7 J8 L6 U1 U2 U3 U4-01 U4-02 U4-03 U5 U6 U7 U8 U9
Add toner Drum unit not installed properly or missing Drum unit due for replacing Wrong drum unit or power was turned on after J7 displayed Key counter or other optional counter accessory problem Drive problem Scan Lens Fuser thermistor High fuser temperature Low fuser temperature 500 sheet cassette lift motor Main board problem Document glass too hot (with document feeder) Problem with line voltage Auto developer setup problem
Sharp 2116, 2118 Code CH CH EE-EL EE-EU F1-00 F1-02 F1-04 F1-05 F1-06 F1-14 F2-31 F2-32
Description Flashing: DV unit not installed, not connected properly Lit steadily: Sorter not installed or not turned on During developer calibration, problem of some kind. Over toned During developer calibration, problem of some kind. Under toned Communication error between main board and sorter Transport motor drive Bin sensor problem. Upper or lower limit sensor problem Sorter bin home sensor Sorter bin motor drive Take out sensor problem Image density sensor problem Drum mark sensor problem Grid voltage correction will not work on the patch voltage is outside the F2-35 expected range H2-00 Fuser thermistor open H3-00 Fuser temperature too high
H4-00 L1 L3 L4 L5 L8-01 L8-03 P PC U2-01 U2-04 U5-00 U5-01 U5-02 U5-11 U5-12
Fuser temperature too low. Lamp, thermal switch, connections Scan forward problem Scan return problem Drive problem; main motor, gear, sensor, bind Lens problem Zero cross (board problem) Auto exposure sensor problem Paper feed problem Card counter not installed Memory loss EEPROM error Communication problem between main board and ADF Registration sensor problem during adjustment, or adjustment value is not a valid number Exit sensor adjustment problem; invalid adjustment value Paper feed drive problem Transport motor drive
Sharp 2120, 2216 Cod e CC CH CH F1 F2 H2 H3 H4 L1 L3 L4 L5
Description Original detection problem Lit Steadily: Sorter not installed, or not turned on Flashing: DV unit not installed, not connected properly, or not latched in place properly Sub code 00: Communication error between main board and sorter. Sub code 02: Sorter transport motor drive. Sub code 31: Image density sensor. Could be a problem with light level. Sub code 32: Drum mark sensor problem. Does not see mark on drum or sensor not working properly. Sub code 00: Fuser thermistor open. Sub code 00: Fuser temperature too high. Sub code 00: Fuser temperature too low. Lamp, thermal switch, connections. Scan forward problem. Motor, sensor, board Scan forward problem. Motor, sensor, board. Drive problem; main motor, gear, sensor, bind. Lens problem. Motor sensor board.
L8 P PC U2
Sub code 01: Zero cross. Paper feed problem or no paper Card counter not installed Sub code 01: Memory loss. Sub code 00: Communication problem between copier and duplex U4 unit. U5 Sub code 00: Communication problem between main board and ADF.
Sharp 2214 Code A1 A2 C1 C2 C3 E1 E3 EE-EL EE-EU J0 J1 J3 J7 J8 L6 U1 U2 U3 U4-01 U4-02 U4-03 U5 U6 U7 U8 U9
Description Jam in document feeder Jam in document feeder Cassette misfeed Cassette feed, bypass unplugged Bypass misfeed Paper feed jam Exit jam Developer overtoned during setup Developer undertoned during setup Developer setup taking place Add toner Drum unit not installed properly or missing Drum unit due for replacing Wrong drum unit or power was turned on after J7 displayed Key counter or other optional counter accessory problem Drive problem Scan Lens Fuser thermistor High fuser temperature Low fuser temperature 500 sheet cassette lift motor Main board problem Document glass too hot (with document feeder) Problem with line voltage Auto developer setup problem
Sharp 2314 Code CH
EE H2 H3 H4 L1 L3 L4 L5 L8
Description If lit steadily, paper feed section cover is open or manual feed unit not installed properly. If flashing, developer seal still installed, or toner density sensor/main board problem. Sub code EU: undertoned. May be toner density sensor problem or developer unit problem. Sub code EL: Over toned. May be toner density sensor problem or developer unit problem. Sub code 0: Fuser thermistor. Sub code 0: Fuser temperature too high. Sub code 0: Fuser temperature too low. Scan problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off. Scan return problem. Sub code 0. Approximately same causes as L1 Sub code 1: Main drive problem. Sensor, gear, motor. Sub code 2: Lens drive, motor, sensor. Sub code 1: Power frequency varies by more than 5 % or for more than 5 sec. Sub code 3: AE sensor problem. Key counter not installed.
PC SPFJA Document feeder problem. M U2 Sub code 1: Main board EEPROM problem. Sub code 4: Memory problem. Sub code 5: high temperature at exposure glass when using document U5 feeder.
Sharp 2414, 2514 Code CH
EE H2
Description If lit steadily, paper feed section cover is open or manual feed unit not installed properly. If flashing, developer seal still installed, or toner density sensor/main board problem. Sub code EU: undertoned. May be toner density sensor problem or developer unit problem. Sub code EL: Over toned. May be toner density sensor problem or developer unit problem. Sub code 0: Fuser thermistor.
H3 H4 L1 L3 L4 L5 L8
Sub code 0: Fuser temperature too high. Sub code 0: Fuser temperature too low. Scan problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off. Scan return problem. Sub code 0. Approximately same causes as L1 Sub code 1: Main drive problem. Sensor, gear, motor. Sub code 2: Lens drive, motor, sensor. Sub code 1 Power frequency varies by more than 5 % or for more than 5 sec. Sub code 3: AE sensor problem. Key counter not installed.
PC SPFJA Document feeder problem. M U2 Sub code 1: Main board EEPROM problem. Sub code 4: Memory problem. Sub code 5: high temperature at exposure glass when using document U5 feeder
Sharp 7100, 7200 Code 0 10 40 8 C1 C2 C3 CH CH H1 H2 H3 H4 H5 H6 H7 H8 L1
Description Stepping motor Mirror motor Dark box switch Mirror motor Charge corona Transfer corona Discharge corona possible DV unit not installed properly Interlock or thermal fuse Heater thermal fuse Thermistor High Temperature Low Temperature Lower thermofuse Lower thermistor High temperature in lower roller Low temperature in lower roller Forward Scan
L2 L3 L4 L5 P1 U1 U2 U3
End of Scan Return of Scan PT/main motor Lens Copy lamp thermal fuse Low battery Data transfer Dark box
Sharp 7320, 7370 Code CH EL EU P flashing P lit PC U3
Description Door open or developer unit out Developer problem Developer set up problem Out of paper No cassette in machine Personal counter not installed Auto exposure sensor problem
Sharp 750 Code 0 10 40 8 C1 C2 C3 CH CH H1 H2 H3 H4
Description Stepping motor Mirror motor Dark box switch Mirror motor Charge corona Transfer corona Discharge corona Interlock or thermal fuse possible DV unit not installed properly Heater thermal fuse Thermistor High Temperature Low Temperature
H5 Lower thermofuse H6 Lower thermistor H7 High temperature in lower roller H8 Low temperature in lower roller L1 Forward Scan L2 End of Scan L3 Return of Scan L4 PT/main motor L5 Lens P1 Copy lamp thermal fuse U1 Low battery U2 Data transfer U3 Dark box SERVICE TIPS & PROCEDURES. Maintenance Counter reset is CROP 20, Print General reset for error codes is CROP 14, Print
Sharp 7900 Cod Description e CC Not sensing document on glass Door open/DV unit not installed CH properly EE DV did not set up properly DV problem-overtoned EL condition DV problem-undertoned EU condition H2 Fuser thermistor H3 Fuser temperature too high H4 Fuser temperature too low L1 Forward scan L3 Return scan L7 Developer unit shift problem PC Key counter U1 Dead battery U2 Battery problem
Sharp 8300, 8350, 8400 Code CC CH EE EL EU H2 H3 H4 L1 L3 L7 PC U1 U2
Description Not sensing document on glass Door open/DV unit not installed properly DV did not set up properly DV problem-overtoned condition DV problem-undertoned condition Fuser thermistor Fuser temperature too high Fuser temperature too low Forward scan Return scan Developer unit shift problem Key counter Dead battery Battery problem
Sharp 8875 Cod e C2 CH H2 H3 H4 L1 L2 L3 L4 L5 L9 U1
Description Transfer corona problem If lit steadily, open door or other interlock. If flashing, developer unit not installed or not connected properly Fuser thermistor Fuser overheat. Triac pinched wire Low fuser temperature. Lamp, thermal fuse, thermistor, connection Scan problem. Did not leave home position Scan left home, but did not complete scan No return scan Drive problem Lens problem Sorter index. If 0 is flashing, sorter index home sensor did not actuate. If 1 is flashing, sorter bottom actuator remained actuated Battery. Replace battery (might have 2) and do simulation 13 to
reset Communication problem within boards. To reset, jumper test points U2 W2 & U2
Sharp Z50, 55, 70 Code (Z70)E H L P
Description Magnification dial not set properly Heater problem (fuser has resettable Scan problem Paper feed problem
Sharp Z60 Code F H L U
Description Thermal fuse - exposure or fuser Heater problem Scan problem Low Battery
Sharp Z800 Code A1 A2 C1 C2 C3 E1 E3 EE-EL EE-EU J0 J1
Description Jam in document feeder Jam in document feeder Cassette misfeed Cassette feed, bypass unplugged Bypass misfeed Paper feed jam Exit jam Developer overtoned during setup Developer undertoned during setup Developer setup taking place Add toner
J3 J7 J8 L6 U1 U2 U3 U4-01 U4-02 U4-03 U5 U6 U7 U8 U9
Drum unit not installed properly or missing Drum unit due for replacing Wrong drum unit or power was turned on after J7 displayed Key counter or other optional counter accessory problem Drive problem Scan Lens Fuser thermistor High fuser temperature Low fuser temperature 500 sheet cassette lift motor Main board problem Document glass too hot (with document feeder) Problem with line voltage Auto developer setup problem
Sharp Z810 Cod e A1 CH H2 H3 H4 L1 L3 L4 L5 P U2 U5
Description Document feeder problem. Toner cartridge not installed or not installed properly. Sub code 0: Fuser thermistor. Sub code 0: Fuser temperature too high. Sub code 0: Fuser temperature too low. Document feeder problem. Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off. Sub code 1: Main drive problem. Sensor gear motor. Sub code 2: Lens drive, motor, sensor Paper feed. Sub code 1: Main board EEPROM problem. 4: Memory problem. Sub code 5: high temperature at exposing glass when using document feeder.
