JRC ECDIS Type Specific Training Model: JAN-701B/901B/2000 JAN-701/901M
1. ECDIS system configuration and initial operation 1.1 How to Power On/ Off the JRC ECDIS
Power ON Press the [POWER] key on the operation panel Power OFF Press the [POWER] key on the operation panel
Caution: Do no t k ee p pre ssing th e [ POW ER ] k ey bec ause the forced OS term inatio n w oul d be p erfor med.
Not required to shut down the windows program with manual
1. ECDIS system configuration and initial operation 1.2 Configuration of Software
Operation software (OS) Windows XP Embedded: The componentized version of Windows XP Professional
Application software JRC ECDIS software: The application software operating on Windows XP Embedded was designed by JRC
1. ECDIS system configuration and initial operation 1.3 Configuration of the disk drive Pass C
Diskdrive SDD
Storagecontent OS, JRC ECDIS software
(Silicon Disk Drive)
D
E
HDD: Master (Hard Disk Drive)
Charts, Routes, Event logs, Own tracks, Alarm lists, User added information and etc.
HDD: Backup
Backup of Master drive
(Hard Disk Drive)
1. ECDIS system configuration and initial operation 1.4 How to check status for malfunction of HDD
Confirming HDD malfunction “
”
“
”
“
”
Open Alarm List panel if Disk1 Error or Disk 2 Error alarm occurs on the bottom of Display panel
Audible & Visual Alarm
1. ECDIS system configuration and initial operation 1.5 How to switch over HDD
Switching over HDD as provisional action Input password “0000” on the startup menu
In the case of D drive(Disk1) is malfunction, switch over to E drive(Disk2) in “Disk Information/Backup” menu Normally work with dual drives (D & E)
1. ECDIS system configuration and initial operation 1.6 The time for replacement of consumables
Hard disk / UPS battery / LCD backlight Recommend to be replaced periodically Periodic replacement Hard disk: 2 years UPS battery: 3 years LCD backlight: 5 years
(UPS: Uninterruptible Power Supply)
N ot e : Parts repl ace ment is ca rr ied o ut by JR C
’
s au th or i z ed e n g i n eer s
1. ECDIS system configuration and initial operation 1.7 Operation of ECDIS under ship power blackout
When AC power supply is stopped due to blackout -Within 1 minute:
The system works without display on LCD In the case of power recovery The system with display goes back to normal -After 1 minute:
The system automatically starts shut down procedure to terminate all the function Occur Blackout
System is working with No display Work only main unit for 1 min
Automatically shut down After 1 minute
1. ECDIS system configuration and initial operation 1.8 Configuration of Navigation sensor connected General System Diagram
RESOLUTION MSC.232(82) ECDIS should be connected to the ship’ s position fixing system, to the gyro compass and to the speed and distance measuring device.
1. ECDIS system configuration and initial operation 1.9 How to shift ENC displayed on JRC ECDIS
Automatic chart redraw Select [MENU] - [(6)Chart] - [(0)Setting] – [(1)S-57/C-MAP…] Border Range Set from 30% to 80%（default)
When set border range is 50%
When set border range is 70%
When ship reaches the border range, the chart automatically shift.
Wide space in the COG direction
N ot e: Onl y eff ec tive in “T rue” motio n
Shifting the chart with the hand cursor 1) Keeping left-clicked 2) Rotate the trackball to move the chart
Hand cursor
Shifting the chart by entering the position from entry panel
Select [MENU] - [(2)Off Center] - [(2)Enter Position]
Enter Position Enter latitude and longitude
Shifting the chart with cross cursor True Motion: Left-click at the designating position
Move to the center of the scr een
Relative Motion: Left-click at the designating position
Move the location of ship display
2. Operation menu on the JRC ECDIS 2.1 Menu structure on the ECIDS
Menu Title Bar When the cursor is moved on the top of screen, the menu title bar opens
Main Menu: (1)AIS/TT, (2)Route, (3)Auto Sail, (4)Ownship/Track, (5)User Map, (6)Chart, (7)Main, (0)Exit
2. Operation menu on the JRC ECDIS 2.2 How to select menu
Selecting menu Select menu from menu lists on the menu title bar
3. Information of ENC 3.1 The difference between ENC/C-MAP/ARCS information and The other information ”
“
“
”
ENC/C-MAP/ARCS information Information belonging to the charts
Chart legend
Name, Edition no., Issue date, Navigation purpose, etc.
Object information
Depth area, Land area, Obstruction, Land mark, Light, etc.
Update history
Edition no., Update date, Accept status, Issue date, etc.
AIO (Admiralty Information Overlay)
Additional information published by UKHO Worldwide admiralty temporary and preliminary notices to mariners (Available on “OTHER” mode)
The other information Information added by users Event mark, Reference point, Navtex mark, User map, etc.
Displaying information of charts with S-57 “
”
/C-MAP/ARCS Information function
1) Right-click on the chart
2) Select [S-57/C-MAP/ARCS Information] 3) Rotate the trackball, point the cursor to the object, and left-click the cursor
S-57 Chart Information
Confirming AIO (Admiralty Information Overlay) “
”
detail with S-57/C-MAP/ARCS Information function
1) Right-click on the chart
2) Select [S-57/C-MAP/ARCS Information] 3) Rotate the trackball, point the cursor to the AIO, and left-click the cursor
AIO view [Menu] -[(6)Chart] -[(4) View AIO]
Click “ Show”
AIO information
Displaying information added on the electronic charts “
”
with Other Information function
1) Right-click on the chart
2) Select [Other Information] 3) Rotate the trackball, point the cursor to the object, and left-click the cursor
User Map
Tidal Stream Mark Event Mark Information Mark
Example: “ Event Mark” information
4. Information and functions provided in the Display panel
Navigation Sensor Information Heading f r om H D G S en s or Speed Through Water f r om S T W S en s or Course Over Ground f r om P r i m ar y S en s or Speed Over Ground f r om P r i m ar y S en s or
Select [M ENU] - [(7)Main] - [(4)Sensor]
Heading setting Heading Source Gyro I/F, Gyro(NMEA)
STW setting
In case of Gyro I/F; Gyro initial value setting is required in the “ GYRO Setting” after Gyro Compass is turned power on
STW Source LAN: orI/F NMEA LOG Local Gyro port:I/F Gyro
POSN1 & POSN2 setting POSN1 Source (Primary Position) DGPS1 or DGPS2 POSN2 Source (Secondary Position) DGPS1 or DGPS2
Difference between GPS displaying position and the own -ship (CCRP) position displayed on the ECDIS CCRP: Consistent Common Reference Point
CCRP Setting only for Serviceman
CCRP position f r om pr i m ar y s en s or
Own ship position offset -Shift to the position designated by left-clicking the cursor -Shift by entering the latitude/longitude Own ship position is shifted -Shift by entering the offset value by entering the offset value
Offset
The panel changes to sky blue
Attention of the own ship position offset function
Do not use the offset function during navigation
The position of ship displayed on the screen is shifted from the real one, and may cause accidents.
Displaying time
Displays current time -In case of “ UTC” Time zone is displayed as +00:00 -In case of “ LMT” Time zone is displayed as a set value
Changing UTC time over local time Push the UTC button to change over LMT (local time) “
”
“
”
Select [MENU] - [(7)Main] - [(0)Setting] – [(3)Date/Time Setting] ”Time Zone” can be changed setting in this menu
Date setting Date Source : GPS1, GPS2 or MANUAL
Time zone setting Time Zone Source GPS1, GPS2 or MANUAL
Select [Date/Time Setting] When Manual is selected as the Source; Date/Time or Time Zone is selectable
Vector length
Vector time: The time for vector length -Ground-referenced velocity -Water-referenced velocity
Select [MENU] - [(4)Own Ship/Track] - [(0)Setting]
“Velocity Time” can be changed setting in this menu
COG vector
HDG vector
doublearrow
singlearrow
Sounding Depth Depth: Water depth and the standard position
Reference position: (Transducer) (Surface) (Keel)
Note
“
”
W hen Echo S ound er is connec ted to the ECD I S , Depth is displ ayed R eference position dep ends on the s ett ing of Echo Sounder. “
”
Selecting the plan route, hand-operated setting of WPT Route: Route name being selected “
UNLOAD
”
appe ars if nothing
is s el ect ed To WPT: Next waypoint being selected
D r op -daw n l is t show s s el ect abl e waypoints DIST: Distance from the ship to the “ To WPT” BRG: Bearing from the ship to the “ To WPT”
Average speed calculation for aim arrival time CALC: (Input ETA to calculation Average Speed)
SPD: Displays average speed to arrive at the destined waypoint ETA: Setting of estimated time of arrival CALC: Calculation Speed mode
s w i tch es ov er by cli ck i n g th i s bu tton
Estimated arrival time calculation by the setting average speed CALC: (Input Average Speed to calculate ETA)
SPD: Setting of average speed ETA: Displays time to go and estimated of arrival
Inputting event mark on the chart When left-clicked, EVENT mark is put at the own position
Event Mark
“ Other
Isolated with Information” menu
MOB (Man Over Board) When left-clicked, MOB (Man-Over-Board) panel opens MOB point symbol Own ship symbol
End MOB mode Keep pressing the [MOB] for 3 seconds or more
MOB panel
List of ports When left-clicked, shows the registered port names Selected the port name position will be Displayed on the chart
Resisting desired position as port list Select [MENU] - [(6)Chart]-[(3)User Setting] -[(1)Save My Port List]
The current position will be registered as My port list with the current scale -Select a chart and scale -Shift the position you want approx. at the center of the chart
Register the position to My Port List with 15 character name
Home position When left-clicked, displays own ship on the screen
Own ship returns to position in the chart area with plenty of room to advance Own ship symbol
Wide area in the direction with reference to COG (GPS data)
Zooming In/Out/Area Zoom In: Magnify the range (RANGE -) Zoom Out: Reduce the range (RANGE +) Zoom Area: Magnify the specified area When left-clicked, the cross cursor changes to the lens cursor
Selected zoom area by the lens cursor
Switching Scale/Range Zoomed out
Scale drop-down list
The cha r t is z oo med in or out ac cordin g to the select ed s ca le Zoomed in Zoomed out
Range drop-down list
The cha r t is zoomed in or out ac co r ding to t he s el ect ed rang e R ang e va lue a re s ame a s R AD AR Zoomed in
Selecting the category of chart information
Category drop-down list
Chang e the o bject ca teg ory by left-click
Base Display:
Important objects that cannot be deleted from charts Standard Display: Objects less important than base display
I nte nded to be used a s a minim um during r out e pl anning and route mo nito r ing Other Display:
Other objects Displays the set objects that belong to standard display Displays all objects that belong to standard display
Some information belonging to the standard category is not display
Setting the category layers Select [MENU] - [(6)Chart]-[(0)Setting]-[(1)S-57/C-MAP/ARCS] “ View1” & “ View2” Tabs View1: Applies to single view screen or “ View1” screen of multi view
View2: Applies to “ View2” screen of multi view
Layers [-]: Displays the objects in [Base], [Standard] and [Other] categories
[S]: Display the objects in [Standard] and [Other] categories
[O]: Display the objects only in [Other] category
Selecting the motion mode Motion drop-down list
Chang e the motion mode by left-click [True]
Ow sh nip
[Relative]
Ow sh nip
[Free]
Ow sh nip
Fixed Chart Fixed
Chart Fixed
When reaches the border range,
Chart moves relatively
chart is automatically shifted
Fixed at the center, but possible to offset
Freely rotate the chart The border range is not effective
Course Up Margin(Chart Rotation) Set from 2
to 20
Azimuth drop-down list
Chang e t he a zim uth mode by left-click [NorthUp]
Own Ship North is upside
True
[CourseUp]
[WPTUp]
Own Ship Heading Course is upside
Own Ship “To WPT” is upside
N/A
N/A
N/A
N/A
Relative Free
[Rotation]
Own Ship Specified degree is upside
Measuring the bearing and distance by EBL/VRM [CCRP EBL/VRM]
[Dropped EBL/VRM] Box shows “D” Dropped EBL/VRM mode
Base point is floating
Base point is CCRP
EBL/VRM using the Display Panel Base point button [Blank] : CCRP D : Dropped point
Displaying position of cross point on EBL1 and VRM1 Displaying position of cross point on EBL2 and VRM2 Active/Inactive button
Units of distance
Active : Displaying “EBL/VRM” Inactive : Displaying “OFF”
[NM] : nautical miles [km] : kilometers [sm] : statute miles
Edit button Active : Displaying “EBL/VRM” operated by dials Inactive : Displaying “OFF”
EBL/VRM using the Operation Panel Displaying the([EBL2]) EBL/VRMkey marker Press [EBL1] to display EBL1 (EBL2) line Press [VRM1] ([VRM2]) key to display VRM1 (VRM2) circle
Turn EBL dial to control
Turn VRM dial to control Own ship
Distance of VRM Azimuth of EBL
Clearing the EBL/VRM marker Press [EBL1] ([EBL2]) key / Press [VRM1] ([VRM2]) key
EBL/VRM using the Context Menu 1) Right-click on the chart 2) Select [Dropped EBL/VRM] or [CCRP EBL/VRM]
DroppedEBL/VRM
CCRPEBL/VRM
Initiating the alarm on the ECDIS Alarm acknowledge-button
[Alarm List] button
Alarm display area
No Alarm
Not acknowledged
Occur Alarm Audible alarm and Visible alarm
Left-click the acknowledge-button or Press [A LAalarm RM ACK ] key
Acknowledged Stop audible alarm
Displaying the alarm list (Alarm status & Alarm log) Left-click the [Alarm List] button on the display panel Icon blinks in red: The alarm occurs and is not acknowledged
Icon stays in red: The alarm is acknowledged but continuing
Icon in green: No alarm
[Alarm Log]
5. Route planning 5.1 How to set up of design parameters
Setting the Route options Select [MENU] - [(2)Route]-[(0)Setting] Date/Time for monitoring:
Display ETA: Displays ETA at Final WPT XTL: Cross track limit Arrival Radius: Arrival radius Speed: Planned ship speed Sail: RL (Rhumb line) GC (Great Circle) ROT: Turn rate Turn Radius: Turn radius Time Zone: Time zone
MAX.Latitude: Waypoints cannot be set in latitudes higher than a set latitude
Limited GC leg to maximum latitude
Route Type: Select a route type when creating a route file Normal: Normal route TCS: TCS (Track Control System)
5. Route planning 5.2 How to design a route with table editing
Route planning using the Table editor Select [MENU] - [(2)Route]-[(1)Route Plannin g] -[(1)Ta ble Editor] New: Start crating a new route Open: Start editing the route file
Save: Save the created or edited route
Insert: Insert new WPT between WPTs Delete: Delete WPT
[WPT to WPT]
CRS: Course to the next WPT DIST: Distance to the next WPT TTG: Estimated time required from waypoint to waypoint CRS: Course to the next WPT DIST: Total distance from waypoint 0 to the specified waypoint ETA: Total time from waypoint 0 to the specified waypoint
[Total]
5. Route planning 5.3 How to design a route with graphic editing
Route planning using the graphic editor Select [MENU] - [(2)Route]-[(1)Route Planning] -[(2) Graphic Editor] New: Start crating a new route Open: Start editing the route file
Property: Edit the parameters of WPT or leg
Add: Add WPT to before WPT0 or final WPT Insert/Move: Insert new WPT be tween WPTs or Move WPT Delete: Delete WPT Save: Save the created or edited route
5. Route planning 5.4 How to check safety status of planned route
Checking the safety status In the Table editor mode
Safety Check: Check the safety of the route W arning dia log box w il l ap pea r i f not safet y Limit Check: Check the limit of the route ( Onl y fo r TCS) W arning dia log box w il l ap pea r w hen exceeding the de In the Graphic editor mode
marcatio n of the sail ing fea ture
Route Safety Check
Not covered area with ENC is futile (vain, ineffective)
Safety Check Symbols: Traffic Separation Zone, Traffic Crossing, Traffic Roundabout, Traffic Precautionary, Two Way Traffic, Deeper Water Route, Recommended Traffic Lane, Inshore Traffic Zone, Fairway, Restrict Area, [Safety Check Result] Caution Area, Offshore Production Area, Military Practice Area, Submarine Transit Area, Ice Area, Channel, Fishing Ground, Fishing Prohibited, Pipeline Area, Cable Area, Anchorage Area, Anchorage Prohibited, Spoil Ground, Dumping, Ground, Dredge Area, Cargo Transshipment Area, Incineration Area, Specially Protected Area, Safety Contour, Coast Line, Obstruction, Under Water Rock, Wreck Cause: Detected error symbols
Route Limit Check Item Turn Radius(Rs)
Course Angle(
s)
Max
Rmax
Limit Value 3Vs/ min
Min
Rmin
3Vs/
Max
max
max
Service Engineer Input
Leg Length(Ls)
Min
Lmin
Planned Speed(Vs)
Max
Vmax
Service Engineer Input
Min
Vmin
Service Engineer Input
ROT(
s)
Max
max
Min
min
L
Service Engineer Input Service Engineer Input
The Safety Check has NOT successfully completed “
”
Shown in red
The Limit Check has NOT successfully completed “
”
Shown in yellow
The planned route has been exceeded the design limits
5. Route planning 5.5 The other function of route editing
Exporting the file of the route In the Table editor or Graphic editor mode, open the route file for exporting Select [MENU] - [(1)File]-[(6)Export] The file name of exporting rot_[date and time].csv
The exported CSV file is possible to be edited with Microsoft Excel on a PC
The drive of exporting destination such as USB device
Note: In case of using USB device as exporting destination, it should be inserted before opening the “Export” screen Can be edited on PC
Importing the file of the route In the Table editor or Graphic editor mode, open the route file for exporting Select [MENU] - [(1)File]-[(3)Import]-[(1)Normal] or [(2)TCS] The file name of importing rot_[date and time].csv
Select the drive of Importing source such as USB device
Note: In case of using USB device as importing source, it should be inserted before opening the “Import” screen
Editing the route with Microsoft Excel Normal route
TCS route
A r r . R ad: O n ly for n or m al r ou te
Can be imported to the ECDIS
6. Route monitoring 6.1 How to set up of the route monitoring
Setting up of the safety contour Select [MENU] - [(6)Chart]-[(0)Setting] -[(1) S-57/C-MAP/ARCS]
Shallow Contour
Safety Depth ( Spot so und ing)
Safety Contour
( Em pha sized c ont our)
Deep Contour
Safety Contour: Depth smaller than the setting value are played enhanced
Isolated Danger
Monitoring the isolated danger
Ship draft is 8.3m The safety safety contour contour may may be be9m 9m
Depth of isolation danger is greater than “safety contour” setting
Isolated danger -obstruction -water rock -wreck Shown in
Depth of isolation danger is equal to or less than “safety contour” setting
symbol
Setting up of the danger detection Vector and Sector Select [MENU] - [(7) Main]-[(0)Setting]-[(8)Alarm Setting ]
Vector: Set up the danger detection vector detects safety contour and danger areas (“Line/AREA” info.)
Sector: Set up the danger detection sector detects danger objects →
(“Spot” info.)
Vector detection
Sector detection
6. Route monitoring 6.2 How to operate the route monitoring
Selecting of the route and information
Select the [Route] from the display panel Initially UNLOAD is selected “
”
***.rtn: Normal route ***.rta: TCS route OK>***.rta: TCS route (Passed Limit check and Safety check
Selecting WPT of the planned route
Next waypoint is being selected Drop-down list shows the selectable waypoints manually
Bearing and Distance from the own ship to the “ WPT”
7. Setting up of ECDIS 7.1 Setting up of displaying AIS/TT
Displaying of AIS/TT target Select [MENU] - [(1)AIS/TT]-[(1)TT1] , [(2)TT2] , [(3)AIS ] or [(4)All] [TT Target] Acquired (in RADAR)
[AIS Target] Sleeping
Activated
Activated Selected
Dangerous (blink)
Activation and inactivating AIS targets Activate AIS target 1) Right-click on the chart display area 2) Click the Activate AIS on the context menu 3) Move the cursor on the TT/AIS target and click “
”
Inactivate AIS target 1) Right-click on the chart display area 2) Click the Deactivate AIS on the context menu 3) Move the cursor on the TT/AIS target and click “
”
COG Variable length) ROT FIX length) HDG FIX length)
Inactivated AIS (Sleeping AIS)
Activated AIS
7. Setting up of ECDIS 7.1 Setting up of displaying AIS/TT
Opening TT/AIS list Select [MENU] - [(1)AIS/TT]-[(6)All List]
View AIS Detail When left-click the [View AIS Detail], the “AIS Information” panel will open
Target ID ID of of TT TT Automatically assigned by RADAR
Displaying TT/AIS information on display panel area Select [ME NU] - [(1)AIS/TT]-[(7)Select List ] AIS Detail When left-click the [AIS Detail], the “AIS Information” panel will open
Setting target filter and CPA/TCPA Select [MEN U] - [(1)AIS/TT]-[(0)AlS/TT Sett ing] CPA/TCPA Limit CPA (Closest Point of Approach): Distance between own ship and target TCPA (Time to Closest Point of Approach): Time to own ship and CPA of target
Filter mode: Ring 20NM Display AIS targets located less than 20 miles
AIS Filter Ring: Display within Heading line Sector area the specified distance Ring area Sector: Display within the specified bearing Own ship with the heading as the center
N ote : Ma x imum 3 00 ta rg et s
7. Setting up of ECDIS 7.2 How to set up of displaying RADAR echo
Displaying the Radar image No.1 Radar image display ON/OFF: Select [MEN U] - [(9)Radar Overlay]-[(1)Radar1]
No.2 Radar image display ON/OFF: Select [MEN U] - [(9)Radar Overlay]-[(2)Radar2] -->The display image can be changed in Radar nm ranges (10 steps) Note: Display Color changes [DAY3] when radar display turns on “
”
Adjusting Radar image for display Select [MEN U] - [(9)Radar Overlay]-[(0)Setting]
Manually adjusted on ECDIS
Operation panel
Radar Option panel
7. Setting up of ECDIS 7.3 How to set up of displaying own ship Select [MENU] - [(4)Ownship/Track]-[(0)Setting]
Selecting Own ship display symbol Own Ship Symbol
Width of ship Length of ship
Symbol
Outline
Setting of Heading and Course vectors
HDG vector: vector: set set by by Gyro Gyro COG vector: Set by GPS
HDG vector COG vector
Setting of Track and Time label display Color of ship track: Red, Green, Blue, Magenta, Orange, Brown or Black Track period: 1,2,4,6,8,12,16,24 hour Maximum displaying period 24 hours
Displaying of danger detection vector and sector
N ote : Plea s e don t fo r g et t o set A la r m L i m i t S etti n g bec ause this da ng er det ect ion setting on the p anel is onl y effect ive for D is pl ay ON / OFF ’
“
”
7. Setting up of ECDIS 7.4 How to set up of display ENC
Setting up of View Common panel “
”
Select [MENU] - [(6)Chart]-[(0)Setting]-[(1)S-57/C-MAP/ARCS] Area Boundary
Plane
Symbolized
Chart Symbol
Paper Chart
Simplified
Setting up of View1 & View2 panel “
”
“
”
Select [MENU] - [(6)Chart]-[(0)Setting]-[(1)S-57/C-MAP/ARCS] Text Size Large: Expand characters Small: Reduced characters
Small
Large
7. Setting up of ECDIS 7.5 How to set up of anchor watch function
Anchor watch alarm alarm Any part of hull go out the anchor monitoring circle
Monitoring dragging anchor
Select [MENU] - [(4)Ownship/Track]-[(2)Anchor Watch] -[(1)Create Monitoring Circle] Occurrence of “ Dragging anchor” alarm
Dragging anchor monitoring circle
Monitoring Circle Default center position : Ship bow
pos s i ble to of f s e t by cu r s or
How to close the dragging anchor monitoring circle Select [MENU] - [(4)Ownship/Track]-[(2)Anchor Watch] -[(2)Clear Monitoring Circle]
7. Setting up of ECDIS 7.6 How to use user map function
Drawing No go line “
”
Select [MEN U] - [(5)User Map]-[(3)User Map Editor ] 1) Left -click the “Ne w” button 2) Select “Line” tab Select Warning Line
“
g No
o li
”
ne “
Vector alarm limit detects No go line
”
Drawing No go area “
”
Select [MEN U] - [(5)User Map]-[(3)User Map Edit or] 1) Left -click the “Ne w” button 2) Select “Area” tab
Select Warning Area
“
a are go o N
”
“
Vector alarm limit detects No go area
”
Drawing entering text Select [MEN U] - [(5)User Map]-[(3)User Map Editor ] 1) Left -click the “Ne w” button 2) Select “Text” tab Select Small font or Large font
“
”
“
”
All objects are displayed on all display categories (Base, Standard, Other)
er Ent
Te x
t
Merging multiple user maps In the User map menu Select [MENU] - [(1)File]-[(7)Merge]
Usermap1
Usermap2
User map 2 User map 1
Chart
Merge as one user map
Chart Chart
Making user map 1
Making user map 2
Individually edited user maps can be be merged merged
Merging user map 1 & user map2
7. Setting up of ECDIS 7.7 How to update ENC with manual
Updating objects manually Select [MENU ] - [(6)Chart]-[(8)Manual Update] Selecting a chart to be edited 1) Left-click on the [Start] button 2) Left-click on the chart to be edited 3) Select object type (Symbol, Line, Area and Text) tab How to delete the updated objects with manual 1) Hide objects that were updated 2) Passed 90 days after the objects were hided 3) Update with the latest official update chart
Note: P lease don
’
t use this
funct ion w ithout c onstraint
7. Setting up of ECDIS 7.8 How to set up of detecting danger situation
Setting up of Alarm detection Select [MENU] - [(7) Main] -[(0)Setting]-[(8)Alarm Setting ] “ Limit”
setting panel
“ Area”
setting panel
Setting up of entering prohibited area Select [MENU] - [(7) Main] -[(0)Setting]-[(8)Alarm Setting ]
Area: Select the areas that are detected as “ danger area”
7. Setting up of ECDIS 7.9 How to set up of Navigation logging function
Displaying the Logbook Select [MENU] - [(7)Main]-[(7)Logbook]
Can not be imported to the ECDIS
The long is exported with CSV format The selected Log is displayed at the center of screen The period of logbook data display
The Logbook setting panel opens ”
”
The selected Log can be edited by manual
Logbook setting Select [MENU] - [(7)Main]-[(0)Setting]-[(5)Logbook setting ]
Logging: Select trigger to record log data
View: Select for displaying the log on the Logbook
Own ship data related to navigation is stored 90days
7. Setting up of ECDIS 7.10 How to set up of volume buzzer
All alarms can be adjusted to silent
Displaying the Logbook
Select [MENU ] - [(7) Main]-[(0)Setting]-[(0)Buzzer Volum e] System Alarm: Ex. POSN1(Data), POSN1 shifted, AC offline Operation Miss: Ex. No Object, Not Allowed Key ACK: Pushing [ALARM ACK] key Setting Alarm: Ex. Safety contour not set, Safety depth not set Navigation Alarm-High, Mid, Low: Ex. Call-back navigator, Crossing Safety Contour, CPA/TCPA Refer to INSTRUCTION MANUAL 9.1 Alarm Function “
”
8. Chart installation and updating 8.1 How to install ENC
Importing ENC/AVCS Chart Import SA Certificate
SA certificate file → Contained in Base CD AVCS: PRIMAR.CRT, ENC: IHO.CRT
Select SA Certificate
Import Cell Permit
Import ENC/AVCS Chart
Cell permit file → Copy to USB or CD/DVD PERMIT.TXT
Import the latest Base CD AVCS: Base CD1-9
Update ENC/AVCS Chart
Update Charts with the latest Update CD
Importing SA Certificate Select [Tool]-[Option]
Insert AVCS Base CD1 (or 2,3, ,9) Select SA Certificate file “ primar.crt”
Left-click the [S-63] tab in the Option panel
Selecting SA Certificate
Select SA Certificate “ primar.crt”
Importing Cell Permit
Insert the USB or CD/DVD copied to Select Permit file “ PERMIT.TXT”
Check the number of chart license
Importing AVCS Chart Select [Sort]-[S-63(Offline)]
Left-click the [Import/Update button]
Insert AVCS Base CD1-9
S-63 chart list
8. Chart installation and updating 8.2 How to update ENC
Updating ENC/AVCS Chart Import SA Certificate
SA certificate file → Contained in Base CD AVCS: PRIMAR.CRT, ENC: IHO.CRT
Select SA Certificate
Import Cell Permit
Cell permit file → Copy to USB or CD/DVD PERMIT.TXT Update by the ACVS Update CD after installing charts by the AVCS Base CD
Import ENC/AVCS Chart
Import the latest Base CD AVCS: Base CD1-9
Update ENC/AVCS Chart
Update Charts with the latest Update CD
Updating AVCS Chart Select [Sort]-[S-63(Offline)]
Left-click the [Import/Update button]
Insert AVCS Update CD
S-63 chart list
Accepting / Not accepting UPDATE information
OK: All update contents a re automatically accepted
Cancel: All update contents are NOT accepted
S h ou ld be acce pted th e u pdates by th e u s e r f r om N av i g ati on & P lan n i n g
Not yet Accepted by the user
Chart update contents Not recognized by the user
Accepted by the user
8. Chart installation and updating 8.3 How to check latest update of ENC
Confirming ENC/AVCS Chart Updating history Confirming by Chart Portfolio Select [Sort]-[S-63(Offline)] Double-click the “[S-63] System Chart”
UpNo.: Edition Update Number
Last Update: Last Update date
Confirming by Navigation & Planning 1)Select [Main]-[Chart]-[Select S-57 Chart] 2)Right-click on the chart 3)Select [S-57/C-MAP/ARCS Information] 4)Rotate the trackball, point the cursor to the object, and left-click the cursor
Update History: Update number (Edition) Update date Issued date
Confirming Expiry date Select [Sort]-[S-63(Offline)] Double-click the “[S-63] System Chart”
Expiry: Expiry date of the Cell Permit
Cell permit has expired
The chart is displayed with a warning message
Updating Cell Permit
Insert the USB or CD/DVD copied to Select Permit file “ PERMIT.TXT”
The validity period of AVCS license Depends on contract Check the number of chart license
Note: A V C S li cen s e i s de fi n ed as pe r i ods of 3 , 6 , 9 or 1 2 m on th s under a l icense a g reem ent w ith cha r t d is tributor
9. Track control system (Automatic sailing) 9.1 What the TCS is
TCS : Track Control System Category
Alias
Category-A
―
Category-B
Category-C
Contents
JRC
Track control for a single straight route or plural routes containing no turning
NO
Assist Turn
Track control for plural routes -Turning by operator’s pressing the TURN” button -Specified turn radius control when turning
YES
Full Automatic
Track control for plural routes -Automatic turning -Track deviation correction when turning
YES
ACK
WOL (Wheel Over Line)
ACK
ECC (Early Corse Change)
ACC (Actual Corse Change)
1-5min before WOL
30sec before WOL
TCS Category-B ECC
ACC
TCS Category-C
ECC
ACC
9. Track control system (Automatic sailing) 9.2 What required before starting TCS
Creating route (Safety check & Limit check) How to make a “OK” TCS route for starting Automatic sailing
Start
Fi le na me: OK> * * * .rt a
Create TCS route in Table editor or Graphic editor
Perform Safety check Perform Limit check
Are there any check errors? Yes No Save the route
End
Modify the route
9. Track control system (Automatic sailing) 9.3 How to operate TCS
Starting Automatic sailing Select “OK” TCS Route in th e drop-down list on the ope ration panel
( R oute na me: O K > ***** ) Select [MENU] - [(3)Auto Sail]-[(1)Start]
Confirm the “Select WP” panel
“Calculate Predict Route?” panel is popped up for the route simulation
“Start Auto Sail?” panel is popped up
Change the Autopilot steering mode to “Navi” mode
( e .g. YOKO GAWA A/
P)
Steering mode selector
Change the steering mode of autopilot from “NAVI” to “AUTO” mode
The Status panel will be changed to “NAVI”
Starting the turn -Category-B Press key when approaching the WOL after the ACC -Category-C Starts turning automatically after reaches at the WOP (WOP: Wheel Over Point)
Stopping Automatic sailing Select [MENU] - [(3)Auto Sail]-[(2)Stop] “Stop Auto Sail?” panel is popped u p
Steering mode selector
Change the steering mode of autopilot from “NAVI” to “HAND” mode
The Status panel will be changed to “HAND”
Operating in emergency (Avoiding dangerous situation) In order cancel automatic sailing: Change theto steering mode of the autopilot from “NAVI” to “HAND” Steering mode selector
Change the steering mode of autopilot from “NAVI” to “HAND” mode
N ot e: ECD I S op era tio n is no t required in an emerg enc y s itua tio n
The left data panel will be popped up Stopped communication between ECDIS and Autopilot
10. Updating of software
Checking the software version Select [MEN U] - [(7)Main]-[(2)Syetem Inform ation]
Maintenance No. : Main software version of the ECDIS
Updating the JRC ECDIS
Software update is carried out by JRC’s authorized engineers
11. Changing over to backup system 11.1 How to transfer planned route to backup system
File Manager Select [MENU] - [(7) Main]-[(2)File Manager] Select “TYPE” : Route File or User M ap Select file “NAME”
Select target system: Main or Backup Left-click “COPY” to transfer file to th e Target system
Delete the selected file
N ot e: I n c ase of ba ckup ECD I S is not instal led , po ss ibl e t o co py fil es to a US B memory for ba ckup purpose
Files that can be handled with the File Manager Local Disk
DVD Drive
USB Device
Ship LAN
Route File
User Map
Own Track
N/A
N/A
Target Track
N/A
N/A
Screen Shot
N/A
N/A
Voyage Log
N/A
N/A
Type
Ship LAN : Master ECDIS and Backup ECDIS are connected through the LAN
12. Operation of former ECDIS 12.1 Difference point of operation between former ECDIS and current ECDIS
Operation panel [Previous ECDIS (M-type)]
AUTO SAILING : [GUARD], [AUTO], [TURN], [SET CO.]
[Latest ECDIS (B-type)]
Display panel [Previous ECDIS ( M-type)]
[Latest ECDIS ( B-type)]
Menu and function
For more information, please refer to Appendix-A “JAN-701/901M ECDIS reference” in the “Training Materials”
Comparison of B-type and M-type B-type (Latest Model)
M-type (Previous Model)
JAN-701B JAN-901B JAN-2000
JAN-701
JAN-901M
Windows XP Embedded
Windows XP Embedded
Windows XP Embedded
Windows NT Embedded
Windows NT Embedded
LCD Size
19inch
23.1inch
19inch
18.1inch
23.1inch
HDD
Master &Backup
Master &Backup
Master
Master &Backup
Master &Backup
Built-in UPS
N/A
USB
N/A
N/A
FDD
N/A
N/A
N/A
Radar Overlay
N/A
Auto Sailing
N/A
OS
