SPECIFICATION SHEET OF JACKET
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
Subject name:
Assignment On
SPEC SHEET OF JACKET
Submitted by : Amit Kr. Singh (01) Anuj Kumar (02) Muneem Meena (22) Ajad Pandey (11) [M. F. Tech Sem-II] Batch-2008-10
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
RAW MATERIAL
FABRIC: SHELL: Contents: Cotton, nylon 3-ply Construction: Warp = 154, Filling = 64 Yarns: Warp = single ply/70, Filling = 3-ply/70. Weave: Plain Weight: 4.0 ozs./sq. yd. Warp stretch: 4% Filling stretch: 4% Dying: High pressure jet dyed Finish: The face has a specialty napping process for cotton aesthetics. REMOVABLE COLLAR LINER: 100% Polar Fleece®, 490 gm. weight. LINING: Face and back is non woven light weight fabric. Interlining is 200 gm. Body and 100 gm sleeves.
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
Product ID 07152930, MENS JACKET Sent Date: 30th MARCH, 2009 Packet Type: Prototype Business Partner Name: xyz Pvt. Ltd
FRONT VIEW
BACK VIEW
PRODUCT OVERVIEW PRODUCT ID: 07152930 PRODUCT NAME: JACKET SEASON: 2009, WINTER BUYER NAME: ABC PVT. LTD ADJACENCY: RTW-READY TO WEAR FABRIC: blended cotton/nylon DEPARTMENT: XYZ SOURCING ZONE DESIGN STRATEGY: INTERNAL DESIGN BRAND: JIN MAO GENDER: MALE SET DATE: 30/03/2009 PACKET TYPE: PROTOTYPE SENT DATE: 10TH DECEMBER 2008 BUSINESS PARTNER TYPE: XYZ PVT. LTD
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
SKETCH (FRONT) Season Brand Item Style View Sample Size
SS 09 JIN MAO MENS JACKET MP 852 B FRONT L
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
SKETCH (BACK) Season Brand Item Style View Sample Size
SS 09 JIN MAO MENS JACKET MP 852 B Back L
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
TABLE OF MEASUREMENT FOR SIZE SET FRONT S.No.
PARAMETER
1 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Full length Shoulder length Shoulder drop Across chest below 1” armhole Arm hole Sleeve length Across hem Front neck drop Neck girth Side seam Sleeve hem Collar smile
LENGTH (INCHES) 26 6.5 1.5 23 22.5 22 40 6 20 16 11.5 4
TOLERANCE (+/-) 1 0 0 1 0 1 0 0 0 0 0 0
BACK S.No.
PARAMETER
LENGTH (INCHES)
13.
Center back length
26
14. 15. 16.
Yoke length Yoke width at armhole level Yoke width at neck line level
20 23 7
TOLERANCE (+/-)
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
1 1 0 0
SPECIFICATION SHEET OF JACKET
CONSTRUCTIONAL DETAIL SHEET LINING There are two inter linings which is made of quilt and nonwoven fabric. In front, back consist of the non woven fabric and sleeve lining consist of the quilt.
FACING In front inside there is a facing of body fabric attached in front inside which has dimension as follow:
S.No.
PARAMETER
17.
Length
18. 19.
Length at zipper level Length at neck line level
LENGTH (INCHES) 12
TOLERANCE (+/-) 1
7 4/8 5 2/8
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
0 0
SPECIFICATION SHEET OF JACKET
POCKET FRONT CHEST POCKETS: There are pocket on the front one is printed and other side without print, set-in pockets with flaps with 2.5” length & 5” width. The pocket opening shall be 5 ” wide and 6” deep there is a print on one pocket The pocket bag shall be made of a good commercial polyester/cotton, non-pill pocketing
S.No.
PARAMETER
20.
Pocket
21.
Flap-
(a) length (b) Width (d) Length (e)Width
LENGTH (INCHES) 6 5 6 2.5
TOLERANCE (+/-) .2 .2 .2 .2
FRONT CROSS POCKETS: There shall be two lower, cross, welted hand warmer pockets set approximately 5.75” from the front zipper. The welts shall be 7 ½” tall and 7/8” wide and secured with a bar tack at each end. There shall be a cord set into the front edge of the welt. There shall be a hidden black, nylon coil closure under the welt. The pocket bag shall be made of a good commercial polyester/cotton, non-pill pocketing. The color of the bag shall be black. The pocket welt will be framed with a ¼” topstitch.
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
INSIDE UTILITY POCKET: There shall be one set-in pocket on the left inside lining. This shall be a double-welted pocket. The functional pocket opening shall be a minimum of 6 ” and the pocket depth shall be a minimum of 8 ½” measured from the top to the bottom of the pocket bag. The pocket bag shall be made of a good commercial polyester/cotton, non-pill pocketing. The color of the bag shall be black.
WAIST BAND
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET WAISTBAND: The bottom of the jacket shall have a 2” side waistband from end to end. Approximately 4” from each zipper side shall be plain and interlined with a good, commercial grade non-woven interlining. On back side shall be secured with 1” wide Velcro
.
MOON PATCH There is a moon patch on which main label attached.
S.No. 22.
PARAMETER Length
LENGTH (INCHES) 3.5
TOLERANCE (+/-) .5
23. 24.
Width at Top Width at bottom
5 2.5
.5 .3
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
FLAP ATTACTHED WITH VELCRO S.No. 25. 26. 27.
PARAMETER Length Width max. Width min.
LENGTH (INCHES) 3.5 1.5 1.0
TOLERANCE (+/-) .2 0 0
COLLAR
CUFF
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
TRIMS & ACCESSORY DETAIL SHEET ZIPPER There shall be a #10 nylon, non-reflective non-freeze 1-way zipper from the bottom of the jacket to the bottom of collar. This shall be interlined with a good commercial grade nonwoven interlining. There will be an inside storm fly on the right front measuring 1 ½” wide from the bottom of the waist to the bottom of the collar. This shall be interlined with a good commercial grade non-woven interlining.
SNAPS There are metal snaps attached on cuffs and front pocket flaps. Total snaps are 6 two each on cuffs and one on flap.
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
VELCRO Two Velcro secured with waist band in back side with loop. Velcro dimensions are as follows: S.No.
PARAMETER
28.
Length
29.
Width
LENGTH (INCHES) 2.5
TOLERANCE (+/-) .1
0.75
0
LABEL LABELS: All labels will be permanent to withstand repeated cleanings for the life of the garment. The following labels shall be applied: MAIN LABEL: There shall be a main label on both the main jacket and removable liner. This shall identify the manufacturer either by name & location, registered trademark. CONTENTS/CARE/SIZE LABEL: There shall be an additional label on both the main jacket and removable liner clearly showing the fabric contents, laundering instructions and garment size.
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
SEAMING & SEWING THREAD SEAMING: All main joining seams shall be overlock safety stitched and then topstitched with a ¼” stitch on the outside. THREAD: All thread shall be poly-core. All main seams shall use a #40 thread, and the balance #60.
PRINITING Here on back side of garment a logo of S’OLIVE Company’s logo printed with rubber printing. One motif printed on front left side above the chest pocket. Chest pocket also printed with rubber printing.
IN FRONT
IN BACK
AT POCKET
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
