Main Contractor :
Client :
Contractor :
NDT Sub Contractor
PYRAMID E&C
Date : 2 !ul" 2#$
Doc% No% &#'($##)#(*RD( ##$
Rev% A
HARDNESS TEST PROCEDURE Project
:
Erection of Crude Fired Heater
Location
:
Fujairah, UAE
Client
:
Ecomar Energy Solutions FZC
eference
:
!"#$%"&$$'$ Contract Agreement
SC (o) *o
:
SC+(+!-
Submitted For: Review/Approval Information Final
1
Main Contractor :
Client :
Contractor :
NDT Sub Contractor
PYRAMID E&C
Date : 2 !ul" 2#$
A
Doc% No% &#'($##)#(*RD( ##$
'# !ul" 2#$
*ardne++ Te+t ,rocedure
Date
De+cription
Rev%
- . Swam" evel III ,repared 0Sievert
Rev% A
Reviewed 0" Contractor/1, C
Approved 0" Client
C.*/E*/S
%$SC,1
2%
134I,M1NT
'% R1F1R1NC1 DC4M1NTS 5%
M1T*D
%
*ARDN1SS R134IR1M1NT AND ACC1,TANC1
6%
R1T1ST
)% R1,RT / DC4M1NTATIN
2
Main Contractor :
Client :
Contractor :
NDT Sub Contractor
PYRAMID E&C
Date : 2 !ul" 2#$
&
Doc% No% &#'($##)#(*RD( ##$
Rev% A
SC.PE T7i+ procedure applie+ to t7e re8uirement for on 9ob 7ardne++ te+tin to be performed at +7op ;oor for pre++ure pipin coil+ weld+ of carbon and low allo" +teel+%
0
E1U2P3E*/
2%$
In+trument +7all be portable 7ardne++ te+ter
2%2
,er+on+ enaed in te+tin +7all be familiar wit7 t7e e8uipment operation and +7all 7ave relevant e>perience in 7ardne++ te+tin wit7 mentioned e8uipment%
%
EFEE*CE 4.CU3E*/S
ASTM A(5#
: Standard Speci?cation for @eneral Re8uirement for Carbon and ow Allo" Steel Tube+%
ASTM 1 $#
: Standard Te+t Met7od for 0rinell 7ardne++ of Metallic Material+%
ASM1 0 '$%'
: ASM1 Code for ,roce++ ,ipin
-
3E/H.4
5%$
In+trument +7all be veri?ed on ASTM 1$# +tandard calibrated te+t bloc 7avin nown 7ardne++% Traceabilit" of t7e te+t bloc +7all be maintained%
5%2
4+e of e8uipment <7ardne++ te+ter= +7all be a+ per manufacturerB+ in+truction manual% 0efore performin 7ardne++ c7ec t7e appropriate mode of te+tin +7all be +et in te+ter%
5%'
T7e +urface to be e>amined +7all be +moot7 free from dirt rea+e oil +cale% Surface +7all be prepared b" li7t rindin or +olvent cleanin
Main Contractor :
Client :
Contractor :
NDT Sub Contractor
PYRAMID E&C
Date : 2 !ul" Doc% No% &#'($##)#(*RD( Rev% A 2#$ ##$ weld+ +7all be ;u+7 round on location b" li7t rindin
amined=% 5%5
*ardne++ te+t +7all be performed after ,E*T w7erever applicable%
5%
T7e 7ardne++ c7ec +7all be performed at weld+ 7eat aected Gone <*AH= and ad9acent ba+e material to weld+% Separation di+tance between readin +7all be +peci?ed a+ per ASTM 1$# re8uirement+
5%6
T7e appeared 7ardne++ value after te+tin +7all be reported and +ame procedure i+ to be followed repeatedl" to tae all re8uired readin a+ per t7e e>tent mentioned below% 0rinell 7ardne++ te+tin mac7ine veri?cation +7all be demon+trated accordin to t7e ASTM 1$# re8uirement+
5%)
Indenter calibration bloc certi?cate +7all be veri?ed b" in+pection aut7orit" prior to proceedin for e>amination%
HA4*ESS E1U2E3E*/ A*4 ACCEP/A*CE *ardne++ in ba+e metal+ weld and 7eat aected Gone a+ per ASTM 1$# +7all not e>ceed t7e followin: For , No% & For , No% $$
!
25$ 0*N 2# 0*N
E/ES/ E7enever an" +pot / +eam fail to meet above re8uirement / IT, re8uirement two additional +pot+ a+ re8uired in 5%5 above +7all be te+ted furt7er more if an" +pot fail to meet re8uirement+ in additional te+t t7e non(conformance report
'
EP./ " 4.CU3E*/A/2.* Report t7e re+ult+ in *ardne++ Te+t Report%
4
Main Contractor :
Client :
Contractor :
NDT Sub Contractor
PYRAMID E&C
Date : 2 !ul" 2#$
Doc% No% &#'($##)#(*RD( ##$
Rev% A
5
