Handbook of Lubricants

S H E L L

C A N A D A

Lubricants Handbook 2002

INTRODUCTION

This handbook provides technical information about Shell lubricants and their applications. Information contained in this handbook is current at the time of publication. Manufacturer’s specifications and Shell’s product data may change at any time. We wish to thank the many contributors to this handbook for their input and their interest in keeping lubrication information up to date and as accurate as possible. Our commitments to quality, service and caring enough to make a difference are shared with every user of this manual. Shell Canada Products also publish “Lubricants Report” technical data sheets which may contain more information than has been included in this handbook. The identifying number of the most recent Lubricants Report is given after the product name and descriptor (in the top right corner of the page) for each product entered in this book. For this information and/or further application information, which may not be contained in this handbook, we invite you to contact Shell at:

The Shell Helps Centre 1-800-661-1600 Facsimile (403) 691-3997 Internet Shell Canada Homepage: www.shell.ca E-Mail: [email protected] For Material Safety Data Sheets (MSDS) Phone (403) 691-2615 Facsimile (403) 691-3321

1.1

INTRODUCTION

Shell Lubricants Handbook

1.2

INTRODUCTION Table of Contents Page Introduction Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ISO Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shell Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Health, Safety and Sustainable Development. . . . . . . . .

1.4 1.5 1.6 1.7

Product Application Guide . . . . . . . . . . . . . . .

2.1 - 2.7

Automotive Lubricants . . . . . . . . . . . . . . . . . . .

3.1 - 3.29

Aviation Lubricants - AEROSHELL . . . . . . . . . .

4.1 - 4.8

Food Grade Lubricants . . . . . . . . . . . . . . . . . . .

5.1

Greases. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.1 - 6.33

Industrial Oils . . . . . . . . . . . . . . . . . . . . . . . . . .

7.1 - 7.62

Marine and Rail Lubricants . . . . . . . . . . . . . . .

8.1 - 8.8

Process Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.1 - 9.5

Specialty Lubricants . . . . . . . . . . . . . . . . . . . . . 10.1 - 10.18 Synthetic Lubricants. . . . . . . . . . . . . . . . . . . . .

11.1

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.1 - 12.26 Product Index (Alphabetical by Name) . . . . .

13.1 - 13.3

1.3

INTRODUCTION Trademarks ™ TRADEMARK OF SHELL CANADA LIMITED ADVANCE SNOW ULTRA,AEROSHELL,ALBIDA,ALEXIA,ALVANIA, ARGINA, CAPRINUS, CARDURA, CASSIDA, CASSIS, CLASSLUBE, CLAVUS, CORENA, CYPRINA, DARINA, DECOL, DELIMA, DENTAX, DIALA, DONAX, DOLIUM, DROMUS, DURSOL, FormulaShell, GADINIA, GARIA, GEARTHERM, MALLEUS, MELINA, MICROGEL, MICROLITH, MORLINA, MYSELLA, NAUTILUS, OMALA, PELLA, RETINAX, ROTELLA, ROTELLA T, ROTELLA ELC, SHELLFLEX, SHELLZONE, SHELL ADVANCE, SHELL FLEET, SHELL INDUSOL, SHELL NATURELLE, SHELL TURBO, SIRIUS, SPIRAX, SRS 2000, STRINGOL, SURSTAY, TELLUS,THERMIA,TIVELA,TONNA,TORCULA, ULTRAGEL, VALVATA,VITREA,VSI, XLA, XTC-50 are trademarks of Shell Canada Limited. Used under license by Shell Canada Products. HYPERIA and OSSAGOL are trademarks of Shell International Petroleum Company. Used under license by Shell Canada Products. In this handbook ‘*’ indicates Trademarks of the following companies: Dexron is a registered trademark of General Motors Corporation Freon is a registered trademark of The DuPont Company Mercon is a registered trademark of Ford Motor Company Mylar is a registered trademark of The DuPont Company Neoprene is a registered trademark of The DuPont Company RAVE is a registered trademark of Bombardier Inc. Teflon is a registered trademark of The DuPont Company TC-WII and TC-W3 are registered trademarks of National Marine Manufacturers Association Viton is a registered trademark of DuPont Canada Inc.

1.4

INTRODUCTION Shell Guarantee

Shell Lubricants ISO 9001 Certified

ISO 9001 is the most comprehensive of the ISO standards. It requires companies to design, implement, and maintain quality control processes throughout their business activities. Shell Lubricants has been accredited under ISO 9001 for its manufacturing facilities. Every manufacturing process that affects satisfaction of Lubricants customers and their needs is regularly audited. Continuous monitoring and improvement are assured through a series of detailed processes, the ISO requirements, and by third party audits.

1.5

INTRODUCTION Shell Guarantee

The Shell Guarantee We believe Shell lubricants are the very best available, and we back these with a no compromise Guarantee: Shell will restore any piece of equipment to full specification performance when damaged due to the failure of our lubricants. We will guarantee the performance of our lubricants when used in accordance with Shell’s recommendations and manufacturer’s requirements and specifications. This warranty applies to all original manufacturer’s equipment. The Shell guarantee is in addition to the OEM’s own warranty, and does not alter nor invalidate it.

1.6

INTRODUCTION Health, Safety and Sustainable Development In Shell Canada we are committed to: • pursue the goal of no harm to people, • protect the environment and pursue the goal of prevention of pollution, • use material and energy efficiently to provide our products and services, • develop energy resources, products and services consistent with these aims, • publicly report on our performance and engage in stakeholder consultation, • play a leading role in promoting best practice in our industry, • manage health, safety and sustainable development as any other critical business activity, and • promote a culture in which all Shell employees share this commitment. In this way we strive to achieve a health, safety and sustainable development performance that we are proud of, to earn the confidence of customers, shareholders and society at large and to be a good neighbor. We contribute to sustainable development through the integration of environmental, social and economic considerations in our decision-making process.

1.7

PRODUCT APPLICATION GUIDE PRODUCT

Airline Oilers

Tellus 22 . . . . . . . . . . . . . . . . . . . . 7.46 Torcula . . . . . . . . . . . . . . . . . . . . . 7.56

Allison C-4 Fluids

Donax TC . . . . . . . . . . . . . . . . . . . 3.6 Donax TD . . . . . . . . . . . . . . . . . . . 3.8 Donax TG . . . . . . . . . . . . . . . . . . . 3.10 Rotella T (All) . . . . . . . . . . . . 3.18 - 3.25

Antifreeze / Coolant

Shellzone . . . . . . . . . . . . . . . . . . . Rotella ELC Coolant. . . . . . . . . . . .

Automatic Transmission Fluid Dexron IIIG/Mercon Type F Aviation Lubricants Engine Oils - Piston

Engine Oils - Turbine Greases Fluids Ball Mills Biodegradable Bilge Cleaner Boat Cleaner Hydraulic 2 Stroke Engine Oils

PAGE

3.4 3.5

Donax TG . . . . . . . . . . . . . . . . . . . 3.10 Donax TF . . . . . . . . . . . . . . . . . . . 3.9

AeroShell Oils . . . . . . . . . . . . . . . . AeroShell Oil W . . . . . . . . . . . . . . . AeroShell Oil W 15W-50 . . . . . . . . AeroShell Oil W 100 Plus. . . . . . . . AeroShell Turbine Oils . . . . . . . . . . AeroShell Greases . . . . . . . . . . . . . AeroShell Fluids . . . . . . . . . . . . . .

4.3 4.4 4.5 4.6 4.8 6.6 4.7

Malleus GL . . . . . . . . . . . . . . . . . . 6.24 Nautilus Biodegr. Bilge Cleaner . . . 10.13 Nautilus Biodegr. Boat Cleaner . . . 10.14 Shell Naturelle HF-M . . . . . . . . . . . 7.33 Shell Naturelle HF-E. . . . . . . . . . . . 7.32 Nautilus Biogradable Outboard Motor Oil . . . . . . . . . . . . . . . . . . 10.9

Caterpillar FD-1 Fluids

Donax CFD 60 . . . . . . . . . . . . . . . 3.11

Caterpillar TO-4 Fluids

Donax TC . . . . . . . . . . . . . . . . . . .

Chainsaw Lubricants Bar and Chain 2 Cycle Engines

Chain Oils . . . . . . . . . . . . . . . . . . . 10.7 XTC-50 . . . . . . . . . . . . . . . . . . . . . 10.18

Circulating Oils

Compressor Oils Air - Recip

Corena S . . . . . . . . . . . . . . . . . . . . Decol H. . . . . . . . . . . . . . . . . . . . . Morlina . . . . . . . . . . . . . . . . . . . . . Tellus . . . . . . . . . . . . . . . . . . . . . . Shell Turbo T . . . . . . . . . . . . . . . . . VSI 68 . . . . . . . . . . . . . . . . . . . . . .

3.6

7.18 7.19 7.30 7.46 7.58 7.62

Corena P . . . . . . . . . . . . . . . . . . . . 7.16 Corena DE (Synthetic). . . . . . . . . . 7.12 2.1

APPLICATION GUIDE

APPLICATION

PRODUCT APPLICATION GUIDE APPLICATION Compressor Oils (continued) Air - Dry Screw

Air - Flooded Screw

Air - Vane

PRODUCT

Tellus . . . . . . . . . . . . . . . . . . . . . . Decol H. . . . . . . . . . . . . . . . . . . . . Donax TG . . . . . . . . . . . . . . . . . . . Donax TG . . . . . . . . . . . . . . . . . . . Corena AS (Synthetic) . . . . . . . . . . Tellus . . . . . . . . . . . . . . . . . . . . . . Corena S . . . . . . . . . . . . . . . . . . . . Corena AS (Synthetic) . . . . . . . . . . Corena S . . . . . . . . . . . . . . . . . . . .

PAGE

7.46 7.19 3.10 3.10 7.10 7.46 7.18 7.10 7.18

Natural Gas/Propane (cylinders & packings only)

Refrigeration Ammonia, CFC (Freons) Ammonia, CFC (Freons), HCFC HFC (R134A), CFC (Freons) & blends Concrete Form Oil Cutting Oils Cylinder Oils (Steam) Drilling Lubricants Electrical Insulating Oil Engine Oils Aviation

Diesel

Gasoline

Gasoline - 2 Stroke Gasoline - 4 Stroke Locomotive (Diesel) Marine (Diesel)

2.2

Corena NG . . . . . . . . . . . . . . . . . . 7.14 Clavus . . . . . . . . . . . . . . . . . . . . . .

7.6

Clavus AB (Synthetic) . . . . . . . . . .

7.7

Clavus HFC 68 (Synthetic). . . . . . . Form Oil 46. . . . . . . . . . . . . . . . . . See Metal Working Fluids Valvata . . . . . . . . . . . . . . . . . . . . . Malleus TC. . . . . . . . . . . . . . . . . . . Diamond Drill Rod . . . . . . . . . . . . Diala A . . . . . . . . . . . . . . . . . . . . . Diala AX . . . . . . . . . . . . . . . . . . . .

7.8 7.25 7.60 6.26 6.22 7.22 7.22

AeroShell Oils (piston) . . . . . . 4.3 AeroShell Oil W (piston) . . . . . 4.4, 4.5 AeroShell Oil W 100 Plus. . . . . 4.6 AeroShell (turbine) . . . . . . . . . . . . 4.8 Rotella T Single Grade . . . . . . . . . . 3.18 Rotella T with XLA (Multigrade) . . 3.20 Rotella T SB . . . . . . . . . . . . . . . . . . 3.22 Rotella T Plus. . . . . . . . . . . . . . . . . 3.24 Shell Fleet . . . . . . . . . . . . . . . . . . . 3.16 FormulaShell (mineral) . . . . . . . . . 3.12 FormulaShell (synthetic blend) . . . 3.12 FormulaShell (synthetic) . . . . . . . . 3.14 FormulaShell SAE 30 & SAE 40 . . . 3.15 See 2 Stroke Engine Oil See Outboard Engine Oils Caprinus . . . . . . . . . . . . . . . . . . . . 8.4 Alexia Oil 50 . . . . . . . . . . . . . . . . . 8.2 Argina . . . . . . . . . . . . . . . . . . . . . . 8.3 Gadinia . . . . . . . . . . . . . . . . . . . . . 8.6 Melina . . . . . . . . . . . . . . . . . . . . . . 8.7 Sirius FB 30 . . . . . . . . . . . . . . . . . . 8.8

PRODUCT APPLICATION GUIDE APPLICATION

PRODUCT

Engine Oils (continued) Natural Gas Railway (Diesel)

Mysella . . . . . . . . . . . . . . . . . . . . . 7.31 Caprinus . . . . . . . . . . . . . . . . . . . . 8.4

Flushing Oil

Cassis A . . . . . . . . . . . . . . . . . . . . .

Food Grade Lubricants Oils Greases

Shell Fluid FM 32. . . . . . . . . . . . . . 7.3 Shell FM Grease 1.5. . . . . . . . . . . . 6.16

Form Oils Concrete

Form Oil 46. . . . . . . . . . . . . . . . . . 7.25

Gear Oils Automotive

Industrial - Enclosed

Industrial Enclosed (with Back stops) Industrial - Open Specialty Worm - Compounded Worm - Synthetic Grease Aviation Grease Automotive Chassis

Drill Rod Electric Motors Enclosed Gear Boxes

Fifth Wheel Food Grade Extreme High Temperature

Dentax . . . . . . . . . . . . . . . . . . . . . Dentax S . . . . . . . . . . . . . . . . . . . . Spirax HD . . . . . . . . . . . . . . . . . . . Spirax S. . . . . . . . . . . . . . . . . . . . . Geartherm. . . . . . . . . . . . . . . . . . . Hyperia S (synthetic). . . . . . . . . . . Omala . . . . . . . . . . . . . . . . . . . . . . Omala HD (synthetic) . . . . . . . . . . Omala RL (synthetic). . . . . . . . . . . Tellus (non EP) . . . . . . . . . . . . . . .

PAGE

7.4

3.26 3.29 3.26 3.28 7.27 7.28 7.38 7.40 7.41 7.46

Morlina . . . . . . . . . . . . . . . . . . . . . 7.30 Malleus GL . . . . . . . . . . . . . . . . . . 6.24 Nautilus Marine Gear Oil . . . . . . . . 10.12 Nautilus Synthetic Gear Oil . . . . . . 10.16 Valvata . . . . . . . . . . . . . . . . . . . . . 7.60 Omala RL . . . . . . . . . . . . . . . . . . . 7.41 Tivela . . . . . . . . . . . . . . . . . . . . . . 7.53 AeroShell Grease . . . . . . . . . . . . . . Darina AX . . . . . . . . . . . . . . . . . . . Darina XL . . . . . . . . . . . . . . . . . . . Albida LC . . . . . . . . . . . . . . . . . . . SRS 2000 . . . . . . . . . . . . . . . . . . . . Diamond Drill Rod . . . . . . . . . . . . Cyprina RA . . . . . . . . . . . . . . . . . . Alvania 2 . . . . . . . . . . . . . . . . . . . . Malleus GL . . . . . . . . . . . . . . . . . . Surstay 000 . . . . . . . . . . . . . . . . . . Retinax TL 00 . . . . . . . . . . . . . . . . Darina XL 102 Moly . . . . . . . . . . . SRS Moly . . . . . . . . . . . . . . . . . . . . Shell FM Grease 1.5. . . . . . . . . . . . Ultragel . . . . . . . . . . . . . . . . . . . . .

6.4 6.18 6.20 6.8 6.30 6.22 6.17 6.14 6.24 6.32 6.28 6.20 6.30 6.16 6.33 2.3

PRODUCT APPLICATION GUIDE APPLICATION Grease (continued) Moly

Multi-Purpose

Natural Gas Valves Open Gear Outdoor Mobile

Railway Journal Roller Bearing Railway Traction Motors Rail Lubricant Semi-Fluid

Steel Mill Synthetic

Thread Compound Water Resistant Wheel Bearing Heat Transfer Oil Hydraulic Oils All Weather Biodegradable Cold Temperature Fire Resistant

2.4

PRODUCT

PAGE

Alvania EP . . . . . . . . . . . . . . . . . . . Darina 102M . . . . . . . . . . . . . . . . . Darina XL EP2 Moly. . . . . . . . . . . . Ossagol C Moly . . . . . . . . . . . . . . . SRS 2000 . . . . . . . . . . . . . . . . . . . . Advance Snow Ultra . . . . . . . . . . . Albida LC . . . . . . . . . . . . . . . . . . . Alvania EP . . . . . . . . . . . . . . . . . . . Darina XL . . . . . . . . . . . . . . . . . . . SRS 2000 . . . . . . . . . . . . . . . . . . . . Dursol K1 . . . . . . . . . . . . . . . . . . . Malleus GL . . . . . . . . . . . . . . . . . . Darina XL 102 Moly. . . . . . . . . . . . Alvania MS . . . . . . . . . . . . . . . . . . Darina XL MS . . . . . . . . . . . . . . . . SRS Winter . . . . . . . . . . . . . . . . . .

6.12 6.20 6.20 6.27 6.30 6.4 6.8 6.12 6.20 6.30 6.23 6.24 6.20 6.12 6.20 6.30

Alvania EP D . . . . . . . . . . . . . . . . . Cyprina RA . . . . . . . . . . . . . . . . . . Ossagol C Moly . . . . . . . . . . . . . . . Cardura . . . . . . . . . . . . . . . . . . . . . Ossagol C Moly . . . . . . . . . . . . . . . Surstay EP 000. . . . . . . . . . . . . . . . Retinax TL 00 . . . . . . . . . . . . . . . . Albida LC . . . . . . . . . . . . . . . . . . . Alvania EP . . . . . . . . . . . . . . . . . . . Darina XL 102 . . . . . . . . . . . . . . . . Advance Snow Ultra Grease. . . . . . Retinax TL 00 . . . . . . . . . . . . . . . . SRS 2000 (Partial Syn.) . . . . . . . . . AeroShell Greases 7, 22 and 33 . . . Malleus TC. . . . . . . . . . . . . . . . . . . SRS 2000 (Partial Syn.) . . . . . . . . . Albida LC . . . . . . . . . . . . . . . . . . . Darina XL EP2 . . . . . . . . . . . . . . . .

6.10 6.17 6.27 6.15 6.27 6.32 6.28 6.8 6.12 6.20 6.4 6.28 6.30 6.6 6.26 6.30 6.8 6.20

Thermia C . . . . . . . . . . . . . . . . . . . 7.52

Tellus T . . . . . . . . . . . . . . . . . . . . . Tellus HD (Synthetic) . . . . . . . . . . Shell Naturelle HF-E. . . . . . . . . . . . Shell Naturelle HF-M . . . . . . . . . . . Tellus HD . . . . . . . . . . . . . . . . . . . AeroShell Fluid 4 . . . . . . . . . . . . . No Fire (WG 200R) . . . . . . . . . . . .

7.50 7.48 7.32 7.33 7.48 4.7 7.36

PRODUCT APPLICATION GUIDE APPLICATION Hydraulic Oils (continued) Indoor

Less Flammable

PRODUCT

Tellus . . . . . . . . . . . . . . . . . . . . . . Decol H. . . . . . . . . . . . . . . . . . . . . Corena S (R&O) . . . . . . . . . . . . . . Shell FR-N . . . . . . . . . . . . . . . . . . .

PAGE

7.46 7.19 7.18 7.34

Lapping Oil

Pella A . . . . . . . . . . . . . . . . . . . . . . 7.42

Locomotive Engine Oils

See Engine Oils, Locomotive Diesel

Machine Tool

Tonna V. . . . . . . . . . . . . . . . . . . . . . . 7.54

Marine Lubricants Engine Oils Turbines

See Engine Oils, Marine Diesel See Turbine Oils

Metal Working Fluids Broaching Cutting Oil (Neat) Grinding Lapping Quenching Rolling Soluble Cutting Oil Tapping & Threading

Garia D . . . . . . . . . . . . . . . . . . . . . Garia T . . . . . . . . . . . . . . . . . . . . . Garia D . . . . . . . . . . . . . . . . . . . . . Garia T . . . . . . . . . . . . . . . . . . . . . Garia D . . . . . . . . . . . . . . . . . . . . . Pella A . . . . . . . . . . . . . . . . . . . . . . Dromus B . . . . . . . . . . . . . . . . . . . Pella A . . . . . . . . . . . . . . . . . . . . . Dromus B . . . . . . . . . . . . . . . . . . . Garia D . . . . . . . . . . . . . . . . . . . . .

7.26 7.26 7.26 7.26 7.26 7.42 7.24 7.42 7.24 7.26

Mineral Oils

Pella A . . . . . . . . . . . . . . . . . . . . . . 7.42 Shellflex . . . . . . . . . . . . . . . . . 9.2 - 9.5 Vitrea . . . . . . . . . . . . . . . . . . . . . . 7.61

Non Drip Oils

Chain Oils . . . . . . . . . . . . . . . . . . . Stringol . . . . . . . . . . . . . . . . . . . . . Tonna V. . . . . . . . . . . . . . . . . . . . . Torcula . . . . . . . . . . . . . . . . . . . . .

Natural Gas Compressor Oils Engine Oils Open Gear Lubricants Outboard Engine Oils

Paper Machine Plunger Pump Packing Oil

10.4 7.44 7.54 7.56

See Compressor Oils, Natural Gas See Engine Oils, Natural Gas Malleus GL . . . . . . . . . . . . . . . . . . 6.24 Nautilus Premium Outboard Motor Oil . . . . . . . . . . . . . . . . . . 10.8 Nautilus Biodegr. Outboard Motor Oil . . . . . . . . . . . . . . . . . . 10.9 Nautilus 4 Stroke Engine Oil . . . . . 10.10 Nautilus Personal Watercraft Oil (synthetic) . . . . . . 10.17 Delima . . . . . . . . . . . . . . . . . . . . 7.20 Delima R . . . . . . . . . . . . . . . . . . . 7.21 Torcula . . . . . . . . . . . . . . . . . . . . 7.56 2.5

PRODUCT APPLICATION GUIDE APPLICATION

PRODUCT

Pneumatic Oil Power Saw Lubricants Bar and Chain Engine Process Oils Pump Oils Quenching Oils Railway Lubricants Journal Roller Bearing Grease Rail Lubricant

See Airline Oilers

Traction Motor Grease Engine Oils Refrigeration Oils Rockdrill Oil Rust Inhibitors Saw Guide Oil

Slide Way Lubricant Soluble Oil Solvents Spindle Oil Snowmobile Lubricants

Steam Cylinder Oil Steam Turbine Oil Synthetic Lubricants Chain Case Oils Compressor Oils

Engine Oils

2.6

PAGE

Chain Oils . . . . . . . . . . . . . . . . . . 10.7 XTC-50 . . . . . . . . . . . . . . . . . . . . 10.18 Shellflex . . . . . . . . . . . . . . . . . . 9.2, 9.4 Nautilus Jet Pump Oil . . . . . . . . . 10.15 See Metal Working Fluids

Alvania EP D . . . . . . . . . . . . . . . . 6.10 Cardura . . . . . . . . . . . . . . . . . . . 6.15 Ossagol C Moly . . . . . . . . . . . . . . 6.27 Cyprina RA . . . . . . . . . . . . . . . . . 6.17 See Engine Oils - Locomotive (Diesel) See Compressor Oils, Refrigeration Torcula . . . . . . . . . . . . . . . . . . . . VSI 68 . . . . . . . . . . . . . . . . . . . . . Sawguide Oil . . . . . . . . . . . . . . . . Stringol . . . . . . . . . . . . . . . . . . . . Tonna V. . . . . . . . . . . . . . . . . . . . Torcula . . . . . . . . . . . . . . . . . . . . Tonna V. . . . . . . . . . . . . . . . . . . . Dromus B . . . . . . . . . . . . . . . . . . Shell Indusol . . . . . . . . . . . . . . . . Tellus 10 . . . . . . . . . . . . . . . . . . . Shell Advance Premium Snowmobile Oil . . . . . . . . . . . . Advance Snow Ultra . . . . . . . . . . Advance Snow Ultra Grease . . . . Advance 100% Synthetic Chain Case Oil . . . . . . . . . . . . . Valvata . . . . . . . . . . . . . . . . . . . . Shell Turbo T . . . . . . . . . . . . . . . . Advance 100% Synthetic Chain Case Oil . . . . . . . . . . . . . Clavus AB . . . . . . . . . . . . . . . . . . Clavus HFC 68 . . . . . . . . . . . . . . Corena AS . . . . . . . . . . . . . . . . . . Corena DE . . . . . . . . . . . . . . . . . Corena NG (Partial Syn) . . . . . . . Advance Snow Ultra . . . . . . . . . . FormulaShell (Partial Syn) . . . . . . FormulaShell . . . . . . . . . . . . . . .

7.56 7.62 7.43 7.44 7.54 7.56 7.54 7.24 7.29 7.45 10.3 10.4 6.4 10.6 7.60 7.58

10.6 7.7 7.8 7.10 7.12 7.14 10.4 3.12 3.14

PRODUCT APPLICATION GUIDE APPLICATION Synthetic Lubricants Engine Oils (continued) Gear Oils

Greases

Hydraulic Oils

PRODUCT

PAGE

Rotella T SB (Partial Syn) . . . . . . 3.22 Nautilus Personal Watercraft . . . . 10.17 Dentax S 50 . . . . . . . . . . . . . . . . 3.29 Hyperia S 220 . . . . . . . . . . . . . . . 7.28 Omala HD . . . . . . . . . . . . . . . . . 7.40 Omala RL (non EP) . . . . . . . . . . . 7.41 Spirax HD 75W-90 (Partial Syn) . 3.26 Spirax S 75W-90 . . . . . . . . . . . . . 3.28 Tivela . . . . . . . . . . . . . . . . . . . . . 7.53 Advance Snow Ultra . . . . . . . . . . 10.4 Darina XL 102 . . . . . . . . . . . . . . 6.20 Retinax TL 00 . . . . . . . . . . . . . . . 6.28 SRS 2000 (Partial Syn.) . . . . . . . . 6.30 Ultragel . . . . . . . . . . . . . . . . . . . 6.33 Tellus HD . . . . . . . . . . . . . . . . . . 7.48

Textile Oils

Tellus 10 . . . . . . . . . . . . . . . . . . . .

7.45

Transformer Oil

Diala A. . . . . . . . . . . . . . . . . . . . . Diala AX . . . . . . . . . . . . . . . . . . .

7.22 7.22

Donax TC . . . . . . . . . . . . . . . . . . Donax TG . . . . . . . . . . . . . . . . . . Dentax . . . . . . . . . . . . . . . . . . . . Dentax S . . . . . . . . . . . . . . . . . . . Donax TF . . . . . . . . . . . . . . . . . . Donax TD / TDL . . . . . . . . . . . . .

3.6 3.10 3.26 3.29 3.9 3.8

Transmission Fluids Caterpillar TO-4 Dexron IIIG/Mercon Heavy Duty Type F Universal Tractor 2 Stroke Engine Oils

Turbine Oils Gas Steam

Shell Advance Premium Snowmobile Oil . . . . . . . . . . . . 10.3 Advance Snow Ultra . . . . . . . . . . 10.4 Nautilus Premium Outboard Motor Oil . . . . . . . . . . . . . . . . . 10.8 Nautilus Biodegradable Outboard Motor Oil . . . . . . . . . 10.9 Nautilus Personal Watercraft Oil . 10.17 XTC-50 . . . . . . . . . . . . . . . . . . . . 10.18 AeroShell Turbine Oils (synthetic) . . 4.8 Shell Turbo T (mineral) . . . . . . . . 7.58 Shell Turbo T . . . . . . . . . . . . . . . . 7.58

White Oil

Shell Fluid FM 32 . . . . . . . . . . . .

7.3

Wire Rope Lubricants

Classlube. . . . . . . . . . . . . . . . . . .

7.5

2.7

3.2

AUTOMOTIVE LUBRICANTS Table of Contents Page General Application Guide Shell Engine Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.3

Antifreeze / Coolant Shellzone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rotella ELC Extended Life Coolant . . . . . . . . . . . . . . . .

3.4 3.5

3.14 3.12 3.15

Gear Oils Dentax Automotive Gear Oils . . . . . . . . . . . . . . . . . . . Spirax HD Gear Oils . . . . . . . . . . . . . . . . . . . . . . . . . . Dentax S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spirax S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.26 3.27 3.28 3.29

Greases Darina XL Albida LC SRS 2000 Darina AX

.................................. .................................. .................................. ..................................

6.20 6.8 6.30 6.18

Transmission Fluids Donax CFD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Donax TG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Donax TD and TDL . . . . . . . . . . . . . . . . . . . . . . . . . . . Donax TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Donax TF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.11 3.10 3.8 3.6 3.9

3.20 3.24 3.22 3.18 3.16

3.1

AUTOMOTIVE

Engine Oils Rotella T with XLA (Multigrade) . . . . . . . . . . . . . . . . . . Rotella T Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rotella T SB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rotella T Single Grade . . . . . . . . . . . . . . . . . . . . . . . . . Shell Fleet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FormulaShell Engine Oils Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mineral and synthetic blend . . . . . . . . . . . . . . . . . . SAE 30 and SAE 40 . . . . . . . . . . . . . . . . . . . . . . . . .

3.2

AUTOMOTIVE LUBRICANTS General Application Guide for Shell Engine Oils

Product Rotella T Plus 15W-40 Rotella T with XLA 10W-30 15W-40 Rotella T 10W 20W-20 30 40 50 Rotella T SB Syn. Blend 10W-40 Syn. Blend 0W-30 Syn. Blend 5W-30 100% Syn. 0W-40 Shell Fleet 10W-30 15W-40 10W 30 FormulaShell 100% Synthetic 5W-30 10W-30 FormulaShell Synthetic Blend 5W-20 5W-30 10W-30 20W-50 FormulaShell 5W-30 10W-30 10W-40 30 40

For For Light For Detroit and Heavy Heavy For Light Diesel Duty Duty 2-Cycle Duty For Diesel Gasoline Diesel Diesel Hydraulics Powered Powered Powered Powered and Engines Engines Engines Engines Ancillaries Yes

Yes

Yes

Yes Yes

Yes Yes

Yes Yes Yes Yes Yes Yes Yes

Yes Yes

Yes Yes

Yes

Yes

Yes Yes

Yes Yes

Yes Yes

Yes Yes Yes Yes Yes Yes Yes Yes

Yes Yes Yes Yes .

. Yes Yes Yes

Yes Yes

Yes Yes

Yes* Yes Yes Yes Yes Yes Yes Yes Yes

*YOU MUST CONSULT OWNERS’ MANUAL FOR APPLICATION OF THIS PRODUCT.

3.3

AUTOMOTIVE LUBRICANTS Shellzone — Universal Antifreeze / Coolant 5.10.05 Recommended Applications: • All-purpose coolant for both heavy-duty and gasolinepowered, liquid-cooled engines Advantages: • Low silicate • Low dissolved solids • Excellent aluminum corrosion protection • Excellent heat transfer properties • Superior anti-foam properties Approvals: • GM 1825M • GM 1899M • ASTM D 3306 • ASTM D 4985 Properties Product Code

SHELLZONE 482-011

Specific Gravity, 15.0/15.0 °C

1.13

pH 33% solution

10.4

Reserve Alkalinity (ml)

11.3

Freeze Point, 50% solution, °C Colour

3.4

-37 Green

AUTOMOTIVE LUBRICANTS Rotella ELC Extended Life Coolant

5.14.04

Recommended Applications: • Heavy-duty diesel engine coolant capable of long life usage • Gasoline-powered, liquid-cooled engines Advantages: • 1,000,000 kms or 12,000 hours of service • One time use of Rotella ELC Extender at 500,000 kms or 6,000 hours • No SCA testing required • No SCA containing filters required • Reduced volume of used coolant for disposal • Rotella ELC / pre-diluted protection to -50°C Approved for/meets requirements of: • Caterpillar EC-1, Detroit Diesel, Cummins, Navistar, TMC RP329,ASTM 3306 and ASTM D4985

Product Codes

Product

482-005

Rotella ELC Extended Life Coolant / Concentrate

482-006

Rotella ELC Extended Life Coolant / Pre-diluted

482-007

Rotella ELC Extender

3.5

AUTOMOTIVE LUBRICANTS Donax TC - Caterpillar TO-4 Fluid

1.31.06

A series of premium Caterpillar TO-4 approved fluids. Recommended Applications: • Cat Powershift transmissions with Variable Capacity Torque Convertors (VCTC) • Cat hydrostatic transmissions • Cat torque convertors, hoists brakes and hydraulic systems • Cat final drives • Also suitable for use in older Cat equipment • NOT to be used as an engine oil Advantages: • Contains an additive system specifically designed for newer Caterpillar transmissions and other drive line components • Improved transmission life • Superior frictional characteristics and efficiency • Suitable for use in older Cat equipment • Three single grades (10W, 30, 50) for seasonal flexibility • One multigrade (Lowtemp) for all-season use in some components • “Lowtemp” is not fully approved for Cat TO-4, though it uses the same performance additives approved for the TG-4 fluid • Formulated for superior antiwear, antifoaming and oxidation stability Approvals: • Single grades are Cat TO-4,TO-2 approved • Allison C-3, C-4

3.6

--

--

7,881

-35°C 2.32 -57

Pour Point, °C

-33

2.10

108

-30

3.50

--

--

73,786

--

97

11.7

50

-21

5.22

--

--

--

31,650

95

19.3

229.3

436-112

Donax TC — Caterpillar TO-4 Fluid

HTHS Visc @ 150°C, cP

-40°C

--

-26°C

--

86,160

--

--

108

6.2

38.3

-15°C

Brookfield Viscosity, cP

190

7.6

100°C

Viscosity Index

35.5

40°C

Viscosity, cSt

30 436-111

436-115

Product Code

10W

LOWTEMP

Grades 436-110

DONAX TC

Properties

AUTOMOTIVE LUBRICANTS 1.31.06

3.7

AUTOMOTIVE LUBRICANTS Donax TD and TDL Universal Tractor Fluids

1.20.02

Mineral based, heavy duty transmission and hydraulic fluid primarily for use where one oil system supplies the hydraulics, transmission, differential, power takeoff, wet brakes and steering. Recommended Applications: • Off highway farm, construction and forestry equipment • Gears, differentials, final drives, transmissions • Hydraulic systems • Bearings • Wet brakes, PTO (power takeoff) clutches Advantages: • TDL is a lighter, low temperature, winter version of Donax TD • Improved EP and antiwear for gears and hydraulic pumps • Frictional characteristics designed to improve braking, reduce chatter and noise in brakes and provide positive clutch engagement • Rust and corrosion protection Approvals: • John Deere J20C (Donax TD), John Deers J20D (Donax TDL) • Ford New Holland M2C134D • Allison C-4 • Recommended for John Deere, Case-International, Ford New Holland, Massey Ferguson,Allis Chalmers, Oliver-White, Kubota,Versatile, Minneapolis-Moline, Deutz-Allis,Agco

Properties Products / Grades

DONAX TD

TDL

Product Code

436-104

436-103

Viscosity, cSt 40°C 100°C

52.4 9.5

34.2 7.1

Viscosity Index

150

189

1,700 -59,300 --

2,465 9,710 20,000

Pour Point, °C

-42

-48

Flash Point, °C

228

190

Brookfield Viscosity, cP @ -20°C @ -25°C @ -35°C @ -40°C

3.8

--

AUTOMOTIVE LUBRICANTS Donax TF - Automatic Transmission Fluid (Type F) Automatic transmission fluid meeting Ford’s EWSM2C33-F (Type F) Fluid Recommended Applications: • Automatic transmissions of some 1977 and earlier Ford cars and trucks where Type F is specified • Other applications where Type F is specified • Saab 900 3-speed transmissions • Jaguar (1990/92 Borg-Warner automatic transmissions) Advantages: • Dyed red for identification Approvals: • Ford EWSM2C33-F (Type F) Properties Grades Product Code

DONAX TF TF 436-107

Colour

Red

Viscosity, cSt 100°C

7.2

Brookfield Viscosity, cSt -18°C -40°C Pour Point, °C Phosphorous, % mass

1,290 34,500 -46 0.022

3.9

AUTOMOTIVE LUBRICANTS Donax TG - Automatic Transmission Fluid (ATF) 1.07.14 Premium, GM Dexron* and Ford Mercon* automatic transmission fluid. Recommended Applications: • GM passenger car and light duty truck automatic transmissions • Where Ford Mercon*,Type CJ and Type H fluids are recommended • Heavy duty truck transmissions requiring Allison C-4 or Cat TO-2 • Hydrostatic drives in construction equipment • Allison V-730 transmissions • Hydraulic systems requiring an ISO 32 grade oil where water demulsification is not required • Oil flooded rotary screw and vane compressors requiring an ISO 32 Advantages: • Outstanding low temperature performance • Frictional characteristics designed to optimize transmission performance • Oxidation and corrosion protection • Antiwear protection for transmissions and hydraulic systems • Detergents and dispersants to improve system cleanliness • Compatible with most seal materials and other mineral oils Approvals: • GM Dexron* IIIG • Ford Mercon*, ESP 138-CJ, M2C 166-H • Allison C-4, Cat TO-2 • Spicer transmissions • Voith DIWA transmission • Meets Vickers 35VQ25 hydraulic pump test • Meets Denison HF-1 and HF-2 requirements for hydraulic vane and piston pump • Sundstrand hydraulics • See our “Lubricants Report for a more complete list

Properties

DONAX TG

Product Code

436-106

Colour Viscosity, cSt

Red @ 40°C @ 100°C

Viscosity Index Brookfield Viscosity, cP @-20°C

36 7.5 200 1,290

Pour Point, °C

-45

Flash Point, °C

175

3.10

AUTOMOTIVE LUBRICANTS Donax CFD 60 - Premier Gear Lubricant for Caterpillar Final Drives/Axles

1.22.01

Specifically designed and approved for modern Caterpillar final drives and axles that do not contain friction materials. Recommended Applications: • Provides greater protection and lubrication of severely loaded gears in Caterpillar final drives and axles compared to conventional TO-4 fluids. • For applications where friction materials are present Donax TC TO-4 approved lubricants are recommended. • NOT recommended for engines, transmissions, hydraulic systems, or final drives and axles that contain friction materials and/or wet brakes. Advantages: • Specifically designed for equipment operating under severe heavy loads. • Provides extended life and reduced wear of final drives and axles. • Excellent Timken and FZG wear performance • Superior oxidation stability and anti-corrosion properties • Compatible with Caterpillar seals and Cat.TO-4 lubricants Approvals: • Approved for Caterpillar final drive and axle lubricant specification FD-1

Properties Product Code Viscosity cSt (mm2/s) at 40°C cSt (mm2/s) at 100°C Viscosity Index Density at 15°, kg/m

Donax CFD 60 436-117 335 25.6 98 3,897

Pour Point, ° C

-15

Flash Point, ° C

253

3.11

AUTOMOTIVE LUBRICANTS FormulaShell - Engine Oils

1.36.06

Mineral and synthetic blend engine oils. Recommended Applications: • Domestic and imported gasoline powered passenger cars and light duty trucks • Recommended for Liquified Propane Gas (LPG) and Compressed Natural Gas (CNG) fuelled engines • 4-cycle motorcycles in the appropriate viscosity grade Advantages: • All-season performance • Synthetic blends provide improved low temperature fast flow characteristics • Superior wear protection • Maintains excellent engine cleanliness • Energy conserving 5W-20, 5W-30 and 10W-30 formulations • Special base stocks to provide low oil consumption Approvals: • API SL, SJ (also older SH) • 5W-20, 5W-30 and 10W-30 grades exceed ILSAC GF-3 (also ILSAC GF-2) • JASO T903 MA Quality

3.12

FormulaShell Engine Oils

425-361

47.1 8.5

157

--4,072

-46.8 -45 190


Viscosity Index

CCS (cranking), cP @ -10°C @ -20°C @ -25°C

Borderline Pumping Temp. (MRV), °C Pour Point, °C Flash Point, °C -36.8 -39 237

-4,995 --

144

67.3 10.5

425-367

-26.2 -33 231

7,181 ---

124

157.0 17.7

425-368

-39.3 -42 225

--5,565

165

64.7 11.1

425-380

5W-30

-36.0 -39 235

-5,578 --

142

68.3 10.5

425-385

10W-30

-33.8 -36 239

-5,973 --

154

97.0 14.5

425-386

10W-40

FormulaShell - Engine Oils

-40.4 -42 225

--5,223

166

64.3 11.1

425-366

Synthetic Blend Synthetic Blend Synthetic Blend Synthetic Blend 5W-20 5W-30 10W-30 20W-50

Product Code

Grades

Properties


3.13

AUTOMOTIVE LUBRICANTS FormulaShell - 100% Synthetic Engine Oils

1.37.02

Premium full synthetic engine oils Recommended Applications: • Domestic, Japanese and European gasoline powered passenger cars and light duty trucks • Including high performance and turbocharged gasoline engines • Light duty diesel engines requiring a CF engine oil • Recommended for Liquified Propane Gas (LPG) and Compressed Natural Gas (CNG) fuelled engines • Recommended for Corvette engines Advantages: • All-season use • Superior wear protection • Excellent engine cleanliness • Outstanding high temperature performance • Superior low temperature performance • Energy conserving • Synthetic base oils provide even lower oil consumption Approvals: • API SL (also older SJ) • ILSAC GF-3 • GM 4718M (Corvette engines) • API CF Properties Grades

FormulaShell 100% Synthetic Engine Oils 5W-30

10W-30

Product Code

425-378

425-379


58 10.5

60 10.1

Viscosity Index

165

150

CCS (cranking),cP @ -25°C @ -30°C

-3,827

3,731 --

Borderline Pumping Temp. (MRV), cP @ -30°C @ -35°C

-12,900

9,500 --

Pour Point, °C

-48

-45

Flash Point, °C

227

235

3.14

AUTOMOTIVE LUBRICANTS FormulaShell SAE 30 and SAE 40

1.38.02

Recommended Applications: • Gasoline-powered engines where single grades are specified • Small construction equipment • 4 stroke lawnmowers • Older farm equipment Advantages: • Superior wear protection • Maintains excellent engine cleanliness • Outstanding high temperature performance • Low oil consumption Approvals: • API SL • API CD (obsolete)

Properties SAE Grade

FormulaShell 30

40

Product Code

425-380

425-384

Viscosity, cSt @ 40°C @ 100°C

96.4 11.5

140,7 14.6

Viscosity Index

107

102

Pour Point, °C

-33

-27

3.15

AUTOMOTIVE LUBRICANTS Shell Fleet - Heavy Duty Engine Oils

1.12.11

Premium engine oils for severe diesel and gasoline service. Recommended Applications: • Moderate and severe service gasoline and diesel mixed fleets • On-highway and off-highway, construction, farm, woodland, marine or stationary power plants • Naturally aspirated and high output turbocharged and aftercooled diesel engines including the latest low-emission designs • High output Cummins, Caterpillar, Detroit Diesel, Navistar and Mack. • Transmissions requiring an Allison C-3 / C-4 or Cat CD / TO-2 transmission fluid including Allison Powershift transmissions • Hydraulics where water separation is not an issue • Ford, GM, Chrysler and other engine builders Advantages: • Soot control -suited for low emission engines where soot related oil thickening is an issue • Oxidation / thermal stability control deposits and engine cleanliness • Wear protection • Base retention neutralizes acids and protects against corrosion • Viscosity retention • Filterability maintained over the life of the oil • Foam control Approvals: • API CH-4, CG-4, CF-4, CF/SJ (15W-40) • API CH-4, CG-4, CF-4, CF/SH (10W-30) • SAE 30 grade meets CF-2,CF • Meets Mack EO-M Plus (15W-40 and 10W-30) • Meets Caterpillar SEBU 6385-02, 6251-05, 6250-04 • Meets Cummins CES 20076 (15W-40 and 10W-30) • Meets Detroit Diesel Bulletin 7SE270 latest version • Volvo VDS (15W-40)

3.16

AUTOMOTIVE LUBRICANTS Shell Fleet - Heavy Duty Engine Oils Properties

1.12.11

SHELL FLEET

Grades

15W-40

10W-30

10W

30

Product Code

431-454

431-452

431-451

431-453


112.1 15.2

72.1 11.1

38.5 6.3

97.7 11.5

Viscosity Index

142

145

113

106

Pour Point, °C

-33

-36

-39

-30

6,229 --

-5,814

-5,328

---

-31

-34

-33

--

CCS Viscosity, cP -20° C -25° C Borderline Pumping Temperature, °C TBN-E Sulphated Ash, %wt

10

10

6

6

1.25

1.25

0.75

0.75

3.17

AUTOMOTIVE LUBRICANTS Rotella T Single Grade Diesel Engine Oils

1.21.02

Premium mineral oil, single grade diesel engine oils Recommended Applications: • Heavy-duty 4 stroke diesel engines • In appropriate grade, Detroit Diesel 2 stroke diesel engines • HD transmissions Advantages: • High temperature piston cleanliness • Freedom from turbo-charger deposits • Resistance to cylinder bore and ring wear • Prevention of low temperature sludge formation Approvals: • API CF (10W and 20W-20 grades) • API CF-2, CF (30, 40 and 50 grades) • API CC, CD (obsolete) • Allison C-4

3.18

113

Viscosity Index

-6,825

---

.75

6.0

---

106

97.7 11.5

431-403

30

---

.75

6.0

---

101

142.1 14.6

431-406

40

ROTELLA T SINGLE GRADE

---

.75

6.0

---

99

216.5 19.1

431-407

50

Rotella T Single Grade Diesel Engine Oils

@-30° C @-20° C

13,600 --

.75

Sulphated Ash, % wt

Apparent Viscosity (MRV) cP

6.0

6.0

TBN-E

.75

3,145 --

110

61.7 8.6

431-402

20W-20

-5,328

@-15° C @-25° C

Cold Crank Simulator

38.5 6.3

431-401

10W

40° C 100° C

Viscosity, cSt

Product Code

Grades

Properties


3.19

AUTOMOTIVE LUBRICANTS Rotella T with XLA - Premium Engine Oils

1.10.31

Shell’s top-of-the-line engine oil for heavy duty diesel and mixed fleets of diesel and gasoline engines Recommended Applications: • Heavy duty 4 stroke diesel engines • Gasoline engines • HD Transmissions • See Rotella T Single Grade Diesel Engine Oils for most Detroit Diesel 2 stroke engine applications • Hydraulic systems where water separation is not needed • Pump and compressor crankcases where product rationalization is important Advantages: • Rotella T with XLA has exclusive advanced additive technology with proven “Million Mile Oil” durability • Excellent deposit control • Suitable for use in multiple applications to reduce oil inventories • Excellent antiwear properties in hydraulic systems Approvals: • API CH-4, CG-4, CF-4,CF • API SJ (15W-40) • API SH (10W-30) • Mack EO-M Plus, EO-M, EO-L Plus • Cummins CES 20076, CES 20071 • Volvo VDS-2 (15W-40) • Allison C-4

3.20

AUTOMOTIVE LUBRICANTS Rotella T with XLA - Premium Engine Oils Properties

1.10.31

ROTELLA T with XLA

Grades

15W-40

10W-30

Product Code

431-405

431-404

Viscosity, cSt 40° C 100° C

100.5 14.0

76.7 11.8

155

149

6,136 --

-5,982

Borderline Pumping, °C

-33

-35

Pour Point, °C

-36

-39

Sulphated Residue, %

1.2

1.3

TBN-E

9.0

10.3

Viscosity Index CCS (cranking), cP @ -20° C @ -25° C

3.21

AUTOMOTIVE LUBRICANTS Rotella T SB - Premium Engine Oils

1.15.08

Synthetic blend versions of Shell’s top-of-the-line engine oil for heavy duty diesel and mixed fleets of diesel and gasoline engines. Recommended Applications: • Heavy duty 4 stroke diesel and gasoline engines • HD transmissions requiring C-4 fluid • Hydraulic systems where water separation is not needed • Pump and compressor crankcases where product rationalization is important Advantages: • Improved soot control • Excellent low temperature properties • Potential fuel economy benefits Approvals: • SB 0W-30:API CH-4, CG-4, CF-4, CF/SJ, Mack E0-M Plus, Cummins CES 20071,Allison C-4 • SB 5W-30:API CF,Allison C-4 • SB 100% 0W-40:API CG-4, CF-4, CF/SJ,Allison C-4 • SB 10W-40:API CH-4, CG-4, CF-4, CF/SJ, Mack EO-M Plus, Cummins CES 20076,Volvo VDS-2,Allison C-4

3.22

AUTOMOTIVE LUBRICANTS Rotella T SB - Premium Engine Oils

Properties

1.15.08

ROTELLA T SB

Grades

10W-40

5W-30

0W-30

0W-40 100% Syn.

Product Code

431-640

431-635

431-630

431-634


91 14.9

67.8 11.5

63.8 11.5

86.2 14.9

Viscosity Index

172

165

177

182

6,200 ---

-5,890 --

--5,101

--4,911

Pour Point, °C

-42

-45

-54

-48


1.2

1.2

1.0

1.2

19,444 ---

-18,881 --

--14,979

--15,076

CCS (cranking), cP @ -25° C @ -30° C @ -35° C

MRV TP-1 @ -30° C @ -35° C @ -40° C

3.23

AUTOMOTIVE LUBRICANTS Rotella T Plus - Premium Engine Oils

1.11.09

All the benefits of Rotella T with XLA plus extended service capability. Shell’s top-of-the-line engine oil for heavy duty diesel and mixed fleets of diesel and gasoline engines Recommended Applications: • Heavy duty 4 stroke diesel engines • Gasoline engines • HD Transmissions Advantages: • All the benefits of Rotella T with XLA, as well as: • Improved soot handling capability • Improved valve train wear • Better oxidation stability • Higher base number (TBN) for control of crankcase acids • Better base number retention • Extended Service capability Approvals: • API CH-4, CG-4, CF-4, CF/SJ • Mack EO-M Plus, EO-M • Cummins CES 20076, CES 20071 • Volvo VDS-2 • Allison C-4

3.24

AUTOMOTIVE LUBRICANTS Rotella T Plus - Premium Engine Oils Properties

1.11.09

ROTELLA T PLUS

Grades

15W-40

Product Code

431-410


100.1 14.0

Viscosity Index CCS (cranking), cP @ -20° C

142 5,720

Borderline Pumping (MRV), °C (based on 60,000 cP max.)

-32

Pour Point, °C

-36


1.4

TBN-E

10

Flash Point, °C

216

3.25

AUTOMOTIVE LUBRICANTS Dentax Automotive Gear Oils

1.27

Dentax 80W-90 and 140 are premium, non-EP automotive gear oils designed for manual transmissions specifying “straight mineral” gear oils meeting API GL-1. Recommended Applications: • Dentax 80W-90 and 140 are straight mineral gear oils designed for use where EP additives are not recommended • Usually recommended for non-ferrous gears including spiral bevel, helical and straight gear applications • Recommended for tractor transmissions and final drives calling for API GL-1 lubricants • Recommended for some manual transmissions, such as Meritor Advantages: • Good oil film strength to protect gears • Contains rust and oxidation inhibitors • Contains viscosity modifiers to improve low temperature flow characteristics Approvals: • Dentax 80W-90 and 85W-140 meet API GL-1

Properties

DENTAX OILS

Grades

80W-90

140

Product Code

436-005

436-004


14.5

31.6

95

92

-100,000 --

112,000 ---

Pour Point, °C

-24

10

Flash Point, °C

235

288

Viscosity Index Brookfield Viscosity, cP @ -12°C @ -26°C @ -40°C

3.26

AUTOMOTIVE LUBRICANTS Spriax HD Automotive Gear Oils

1.08.13

Spirax HD oils are premium extreme pressure automotive hypoid gear oils. Recommended Applications: • Spirax HD oils are approved for drive-train gears in heavily loaded equipment and passenger cars • Including hypoid, spur, helical, spiral-bevel and worm gears in differentials, manual transmissions, final drives, transfer cases and steering mechanisms • Spirax HD 85W-140 is typically used in off-highway applications • See Shell Spriax “S” 75W-90 for extended warranty applications Advantages: • Spirax HD oils contain EP additives for superior load carrying capacity in heavy duty applications • Superior thermal and oxidation stability • Spirax HD 75W-90 is a semi-synthetic oil for improved low temperature performance and reduced frictional losses for improved fuel economy Approvals: • Spirax HD 80W-90 and 85W-140 meet API GL-4, GL-5, API MT-1, MIL-L-2105D and MIL-PRF-2105E • Spirax HD 80W-90 and HD 85W-140 are Mack GO-H and GO-J approved • Spirax 75W-90 meets API GL-5 Properties

SPIRAX HD GEAR OILS

Grades

75W-90

80W-90

85W-140

Product Code

437-010

437-006

437-007


109 19.2

139 14.8

411 29.7

Viscosity Index

195

110

103

--123,000

-136,000 --

78,800 ---

< -45

< -35

< -20

Brookfield Viscosity, cP @ -12°C @ -26°C @ -40°C Channel Point, °C Pour Point, °C

-42

-27

-12

Flash Point, °C

195

218

200

3.27

AUTOMOTIVE LUBRICANTS Dentax S - 100% Synthetic Heavy Duty Transmission Fluid

1.29.02

A premium, 100% synthetic, non EP, manual transmission fluid for extended oil drain warranty programs Recommended Applications: • Manual transmissions and transfer cases of trucks, farm and construction equipment requiring a GL-1 type lubricant • Severe service Advantages: • Extended drain / warranty programs • All-season operation • Outstanding low temperature performance • Outstanding winter fuel economy Approvals: • Meets API GL-1 requirements • Meets API MT-1 test requirements • Eaton-Fuller PS-081 extended warranty program (E250) • Eaton-Fuller PS-164 extended warranty program (E500) • Meritor 0-81-E extended warranty program

Properties Grades

DENTAX S SAE 50

Product Code

436-007


127 18.2

Viscosity Index

151

Pour Point, °C

-40

Brookfield Viscosity, cP -30°C

3.28

38,000

AUTOMOTIVE LUBRICANTS Spirax S - 100% Synthetic Heavy Duty Automotive Gear Oil

1.28.10

Spirax S is a premium, 100% synthetic, extreme pressure automotive gear oil, approved for Eaton-Fuller and Meritor extended warranty programs. Recommended Applications: • Severe service automotive gear applications • Differentials, heavy duty axles, transfer cases, manual transmissions of trucks, farm equipment, automobiles and heavy construction equipment • Some industrial gear applications requiring wide temperature capabilities in an ISO 100 or 150 grade Advantages: • Extended drain warranty program approved • Full synthetic base oil • Excellent wear protection -full automotive EP additive system • Outstanding flow at low temperatures • All season operation • Improved winter fuel economy Approvals: • API GL-5, MT-1 • Meritor 0-76-E, 0-76-N • Eaton Fuller PS-037 (E250), PS-163 (E500) • Mack Truck GO-J, GO-J Plus • Dana Corporation,Axle Division • MIL-L-2105D • MIL-PRF-2105E

Properties

SPIRAX S

Grades

75W-90

Product Code

437-013


122 16.6

Viscosity Index

147

Channel Point @ -51°C

Pass

Pour Point, °C

-45

3.29

AVIATION LUBRICANTS Table of Contents Page

4.7 4.7 4.7 4.7

Greases AeroShell Grease 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . AeroShell Grease 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . AeroShell Grease 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . AeroShell Grease 14. . . . . . . . . . . . . . . . . . . . . . . . . . . AeroShell Grease 22. . . . . . . . . . . . . . . . . . . . . . . . . . . AeroShell Grease 33. . . . . . . . . . . . . . . . . . . . . . . . . . .

6.6 6.6 6.6 6.6 6.6 6.6

Piston Engine Oils AeroShell Oil W 15W-50 (semi-synthetic) . . . . . . . . . . . AeroShell Oil W (dispersant) . . . . . . . . . . . . . . . . . . . . AeroShell Oil W 100 Plus (dispersant) . . . . . . . . . . . . . AeroShell Oil (non-dispersant) . . . . . . . . . . . . . . . . . . .

4.5 4.4 4.6 4.3

Turbine Engine Oils AeroShell 560 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AeroShell 555 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AeroShell 500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.8 4.8 4.8

4.1

AVIATION

Fluids AeroShell Fluid 2F . . . . . . . . . . . . . . . . . . . . . . . . . . . . AeroShell Fluid 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AeroShell Fluid 41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shell LGF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

AVIATION LUBRICANTS

4.2

AVIATION LUBRICANTS AeroShell - Piston Engine Oils

5.01.01

AeroShell (non dispersant) aviation piston engine oils. Recommended Applications: • All grades are for use in 4 stroke certified aircraft reciprocating piston engines and aircraft radial engines which do not require a dispersant additive (AD type) containing oil Advantages: • AeroShell Oils are oxidation inhibited high quality mineral oils Approvals: • SAE J-1966 (formerly MIL-L-22851D)

Properties

AEROSHELL OIL

Grades

80

100

120

SAE Viscosity Grade

40

50

60

Product Code

420-010

420-015

420-020


143 14.6

232 19.9

318 25.0

Pour Point, °C

-30

-21

-15

Flash Point, °C Ash Content, % m

282

292

304

0.001

0.002

0.001

4.3

AVIATION LUBRICANTS AeroShell Oil W - Piston Engine Oils

5.02.01

AeroShell Oil W (dispersant) monograde aviation piston engine oils. Recommended Applications: • AeroShell Oil W grades are for use in 4 stroke certified reciprocating piston engines, including fuel-injected and turbocharged engines. NOT recommended for automotive engines converted for use in aircraft • For multigrade aviation piston engine oil see AeroShell Oil W 15W-50 oil Advantages: • AeroShell Oil W oils promote engine cleanliness, eliminate sludge, reduce oil consumption and protect against scuffing and wear Approvals: • SAE J-1899 (formerly MIL-L-22851D)

Properties Grades

AEROSHELL OIL W (PISTON ENGINE OILS) W80

W100

W120

40

50

60

Product Code

420-030

420-035

420-040


118 14.1

199 19.7

278 24.6

Viscosity Index

118

113

112

SAE Viscosity Grade

Pour Point, °C

-33

-30

-18

Flash Point, °C

264

288

284

0.003

0.003

0.003

Ash, % m

4.4

AVIATION LUBRICANTS AeroShell Oil W 15W-50 Piston Engine Oil

5.09.09

A premium quality, synthetic blend, ashless dispersant, multigrade aviation piston engine oil. Recommended Applications: • 4 stroke cycle aircraft piston engines • All season service • Used where a dispersant type aviation grade 100 (SAE 50) oil is specified Advantages: • Synthetic blend, antiwear, ashless dispersant formulation • Designed specifically to improve the low temperature flow characteristics and provide superior lubrication at higher engine operating temperatures • Significantly reduced flow time to the oil gallery versus 20W-50 and 65 grades at low temperatures • Excellent wear and corrosion protection • No need to add Lycoming LW16702, as this oil contains an approved equivalent Approvals: • Textron-Lycoming (Service No. 1409A, 1014K and Bulletin 446C) • Teledyne Continental spec MHS-24 (Service Bulletin M81-11) • Pratt & Whitney (all radial engines, Service Bulletin 1183 Rev T.) • SAE J1899 (formerly MIL-22851D) • Bell Helicopters Model 47 transmission (Tech Bulletin 47-81-4)

Properties

AEROSHELL OIL W 15W-50

Grades

15W-50

Product Code

420-060


110 19.4

Viscosity Index CCS (cranking) Viscosity, cP -15°C

170 3,100

Pour Point, °C

-42

Flash Point, °C

258

4.5

AVIATION LUBRICANTS AeroShell Oil W 100 Plus Piston Engine Oil

5.15.01

A premium quality, ashless dispersant type aviation piston engine oil with improved corrosion resistance, enhanced antiwear properties, and includes approved equivalient of LW 16702 additive. Recommended Applications: • 4 cycle aircraft piston engines • All types of service • Used where a dispersant type aviation oil grade 100 is required • Used where LW 16702 is specified as an approved equivalent additive is included in the formulation • NOT recommended for helicopters with a common sump for engine and transmission oil Advantages: • Antiwear, ashless dispersant formulation • Excellent wear and corrosion protection • Excellent oxidation stability and heat dissipation • No need to estimate the amount of LW 16702 additive because it is already included in AeroShell Oil W 100 Plus Approvals: • Textron-Lycoming (Service No. 1409A, 1014K and Bulletins 446B, 446C and 446D) • Teledyne Continental spec MHS-24 (Service Bulletin M81-11) • Pratt & Whitney (all radial engines, Service Bulletin 1183 Rev T.) • SAE J1899 (formerly MIL-22851D) • FAA AD 80-04-03 R2

Properties Grades

AEROSHELL OIL W 100 PLUS 100

Product Code

420-065


213 20.2

Viscosity Index

110

Pour Point, °C

-20

Flash Point, °C

260

4.6

AVIATION LUBRICANTS AeroShell Fluids Four premium products for various aviation applications Recommended Applications: • AeroShell Fluid 2F is a corrosion inhibiting oil intended for preserving internal engine parts during storage • AeroShell Fluid 4 is a mineral oil based aviation hydraulic fluid • AeroShell Fluid 41 is a “super clean” hydraulic fluid • Shell LGF is used in landing gear strut mechanisms Advantages: • Fluid 2F has an anti-corrosion additive package and may be used as a “flyaway” oil for up to 50 hours after storage • Fluid 4 and 41 are mineral hydraulic oils that provide excellent low temperature fluidity Approvals: • Fluid 2F is a P-10 preservative under MIL-C-6529C • Fluid 4 is approved for MIL-H-5606A (obsolete) • Fluid 41 is approved for MIL-H-5606G for “super clean” fluids • Shell LGF is approved for many commercial aircraft • See our “Lubricants Report” for more details

Properties Products

AEROSHELL FLUIDS Fluid 2F

Fluid 4

Fluid 41

Shell LGF

Product Code

421-035

421-150

421-141

421-152

Colour

Dk Amber

Red

Red

Yellow

-20.0 --

13.5 5.1 480

13.6 5.1 380

13.7 5.0 390

Viscosity, cSt 40°C 100°C - 40°C TANE

--

0.03

0.07

5.0

0.004

--

--

--

Pour Point, °C

-10

-60

-60

-60

Flash Point, °C

210

88

88

10

Ash, % mass

4.7

AVIATION LUBRICANTS AeroShell Turbine Engine Oils

5.13.01

100% synthetic gas turbine engine oils. Recommended Applications: • AeroShell Turbine Oil 500 is approved for use in aviation turbines and industrial gas turbine engines • AeroShell Turbine Oil 555 is approved for use in aviation turbines and helicopter transmissions • AeroShell Turbine Oil 560 is approved for aviation turbines and industrial gas turbine engines Advantages: • AeroShell Turbine Oil 560 is a third generation “low coking” oil designed for newer high bypass engines • Improved thermal and oxidation stability Approvals: • AeroShell Turbine Oil 500 is MIL-PRF-23699F Grade STD approved • AeroShell Turbine Oil 555 is DOD-L-85734 approved and also meets MIL-PRF-23699F standards • AeroShell Turbine Oil 560 is MIL-PRF-23699F Grade HTS approved for newer generation engines • Please refer to our “Lubricants Report” for a complete listing of engine manufacturer and model approvals.

Properties Products

AEROSHELL TURBINE OILS 500

555

560

Product Code

420-120

420-121

420-130

Viscosity, cSt 40°C 100°C - 40°C

25.3 5.2 10,025

29.0 5.4 10,775

28.3 5.3 10,775

-54

-54

< -54

Pour Point, °C max Flash Point, °C min

246

246

260

TANE

0.11

0.14

0.14

Ryder Gear Test, % Hercolube A, 102 min.

117

> 145

126

4.8

FOOD GRADE LUBRICANTS Designations and Table of Contents The following Shell lubricants satisfy the requirements for food contact:

Product

US FDA

CFIA

Satisfies

Approved

Page

GREASES Alvania EP Shell FM Grease Darina XL – EP2, Moly, MS, 102 Moly

n1 H1

SRS 2000

6.12 6.16

n1

6.20

n1

6.30

OILS Shell Fluid FM 32 Corena AS

H1

n3

7.3

n1

7.10

Diala AX

n1

7.22

Dromus B

n1

7.24

Morlina

n1

7.30

n1

7.38

Omala HD

n1

7.40

Omala RL

n1

7.41

Tellus

n2

7.46

Tellus T

n2

7.50

Shell Turbo T

n1

7.58

Federal departments (Drug Administration,Agriculture, etc.) monitor the use of lubricants used in food processing plants. US FDA Designations: H1: Satisfactory for incidental contact with food. CFIA (Canadian Food Inspection Agency) Designations: n1: For general use; avoid food contamination during application and storage. n2: Hydraulic oil; avoid food contamination during application and storage. n3: Protective coating oils. 5.1

FOOD GRADE

Omala 68, 100, 150, 220, 320, 460, 680, 1000

GREASES Table of Contents Page Grease Reference Chart . . . . . . . . . . . . . . . . . . . . . . .

6.3

Automotive Chassis / Wheel Bearing Darina XL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.20 Albida LC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.8 SRS 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.30 Darina AX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.18 Aviation AeroShell Greases . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.6

Drill Rod Diamond Drill Rod. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.22 Electric Motor Cyprina RA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.17 Alvania 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.14 Food Machinery Shell FM Grease 1.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.16 High Temperature (Extreme) Ultragel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.33 Moly Darina XL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.20 Alvania EP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.12 SRS 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.30

Non-EP Bearing Alvania 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.14

6.1

GREASES

Multi-Purpose Darina XL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.20 Albida LC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.8 SRS 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.30 Alvania EP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.12

GREASES Table of Contents (continued) Page Open Gear Malleus GL Multilube . . . . . . . . . . . . . . . . . . . . . . . . . . 6.24 Railway Cardura . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.15 Alvania EP D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.10 Cyprina RA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.17 Semi-Fluid Surstay EP 000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Retinax TL 00. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ossagol C Moly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alvania EP Arctic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alvania EP Arctic Moly . . . . . . . . . . . . . . . . . . . . . . . . .

6.32 6.28 6.27 6.12 6.12

Snowmobile Advance Snow Ultra. . . . . . . . . . . . . . . . . . . . . . . . . . .

6.4

Synthetic Darina XL 102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.20 Retinax TL 00. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.28 SRS 2000 (Partial Synthetic) . . . . . . . . . . . . . . . . . . . . . 6.30 AeroShell Greases . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6 Thread Compound Malleus TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.26 Valve (Sour Gas) Dursol K1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.23 Water Resistant SRS 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.30

6.2

GREASES Grease Reference Chart Application/ Characteristic

Darina XL

SRS 2000

Albida

Alvania EP

102M

EP-2 (M)

S

W

EP-1&2

EP-1&2

MS (M)

High Temp

1

2

3

X

2

3

X

Low Temp

1

3

X

2

3

3

2

Mechanical Stability

1

2

1

2

2

2

2

Water Resistance

3

2

1

2

2

2

3

Anti Rust

2

2

1

2

2

2

3

Extreme Pressure (EP)

1

2

2

2

2

2

2

Farming

2

1

2

3

2

2

3

Construction

1

2

2

3

2

2

3

Trucking

2

2

1

2

1

2

3

Manufacturing

1

1

1

3

1

2

3

Marine-Leisure

1

2

2

1

2

2

3

Logging

1

2

2

3

2

2

3

Wheel Bearings

1

1

3

X

1

3

X

Other Bearings

2

2

3

3

2

1

3

Pillow Blocks

1

2

X

3

1

2

3

General Chassis Components

1

2

2

3

2

2

3

King Pins, Cups and Saucers

2

3

1

3

2

2

3

Universal Joints

3

3

1

3

2

2

3

Slack Adjusters

2

3

2

2

2

2

3

Pins and Bushings

1

2

1

3

2

2

3

5th Wheels

1

2

1

2

2

2

3

Splines, Yokes

2

3

2

3

1

2

3

Couplings

3

3

1

3

2

2

3

Car Washes

3

2

1

2

2

2

3

Boat Trailers

3

2

1

2

2

2

3

ATVs

2

2

2

2

2

2

3

Irrigation

3

2

1

3

2

2

3

1=Excellent; 2=Very Good; 3=Good; X=Not Suitable

(M)=Moly Grades 6.3

GREASES Advance Snow Ultra - Synthetic Snowmobile Grease A fully synthetic, extreme pressure (moly) grease. Recommended Applications: • All snowmobile grease applications including recreational, competitive racing and long endurance conditions • Chassis points, pins and bushings, plain and rolling element bearings Advantages: • Synthetic base oils provide better performance over a wider temperature range • Excellent load carrying / shock loading ability to minimize bearing and suspension wear • Contains a fine dispersion of moly extreme pressure additive • Superior low temperature mobility and dispensability • Excellent lubrication as low as -40°C • Excellent resistance to water washout • Excellent adhesive qualities • Superior mechanical stability • Prevents corrosion Approvals: • Meets NLGI GC-LB wheel bearing and chassis requirements

Properties NLGI Grades

1

Product Code

504-593

Colour Thickener type Dropping Point, °C

Grey Microgel 260 +

Base Oil Viscosity, cSt 40°C

100

4 Ball Wear, mm

0.6

4 Ball EP, Load Wear Index

70

Est. Operating Range, °C Min. Dispensing Temp, °C (may vary with grease gun or application technique)

6.4

ADVANCE SNOW ULTRA GREASE

-45 to 170 -40

GREASES

6.5

GREASES AeroShell Greases Six premium greases designed for aviation applications and specifications, utilizing various thickeners and both mineral and synthetic base oils. Recommended Applications: • AeroShell Grease 5: wheel bearings, high speed accessories such as starters • AeroShell Grease 6: multi-purpose, anti-friction and plain bearings • AeroShell Grease 7: heavily loaded gears, actuators, propellers, screws • AeroShell Grease 14: helicopter main and tail rotor bearings • AeroShell Grease 17: heavily loaded boggie pins on landing gear assemblies • AeroShell Grease 22: high speed, heavily loaded applications over wide temperature ranges • AeroShell Grease 33: multi-purpose airframe grease developed for Boeing 3-33A Please Note:AeroShell greases are not necessarily compatible with other greases. Always be sure to clean and completely remove all old greases before installing the new AeroShell greases. Advantages: • AeroShell greases are designed to resist oxidation and thermal breakdown, resist water washout, and prevent corrosion • Provide high load carrying capabilities in the intended applications • Perform over a wide range of temperatures

6.6

+215

31.8

281 284

Dropping Pt, °C

Oil Viscosity, @ 98.9°C

Penetration @ 25°C Unworked Worked

US Military Approvals

MIL-G-3545 (obsolete)

-23 to +177

Mineral

Base Oil

Operating Temp Range, °C

Amber

Microgel

Thickener

519-005

Product Code

Colour

Grease 5

Grades

Properties

283 296

3.1

+260

Synthetic

Microgel

Buff

519-010

Grease 7

-54 to +93

267 273

3.1

+148

Mineral

Calcium

Tan

519-015

Grease 14

MIL-G-24139 MIL-PRF-23827 MIL-G-25537

-40 to +121 -73 to +149

287 300

5.5

+215

Mineral

Microgel

Brown

519-006

Grease 6

MIL-G-21164

-73 to +149

287 295

3.1

+260

Synthetic

Microgel

Dark Gray

519-025

Grease 17

AEROSHELL GREASES

MIL-G-81322 Grade A

-65 to +204

271 275

5.8

+260

Synthetic

Microgel

Tan

519-035

Grease 22

MIL-PRF-23827 BMS 3-33A

-73 to +121

290 297

3.4

+250

Synthetic

Lithium

Green

519-033

Grease 33

GREASES

AeroShell Greases

6.7

GREASES Albida LC - Premium Multi-Purpose Grease

3.74.06

A premium, multi-purpose, high temperature, extreme pressure lithium complex grease. Recommended Applications: • General multi-purpose, heavy duty applications • Including mining and smelting, steel, pulp and paper, and cement industries • Pins and bushings, plain and rolling element bearings Advantages: • Compatible with most other greases • Outstanding mechanical stability • Temperature range from -40 to 160°C • Excellent load carrying ability • Superior low temperature mobility and dispensability • Resistant to water washout • Excellent rust protection • Coloured green for identification Approvals: • EP-1 and EP-2 meet NLGI GC-LB wheel bearing and chassis requirements

6.8

-15

299

220

0.5

54 400

Dropping Pt, °C

Base Oil Viscosity, cSt @ 40°C

4 Ball Wear, mm

EP Tests 4 Ball, Load Wear Index 4 Ball, Weld Load

-20 to +160

280

Lithium complex

Min dispensing temp °C (may vary with grease gun or application technique)

Est. Operating Range, °C

Worked Penetration 60 strokes at 25°C

Thickener Type

Green

2

Colour

504-700

NLGI Grade

EP-2

Product Code

Product

Properties

54 400

0.5

160

293

-25

-30 to +160

325

Lithium complex

Green

1

504-703

EP-1

45 315

0.5

20.8

271

-35

-40 to +80

325

Lithium complex

Green

1

504-702

EP-MS

Albida LC - Premium Multi-Purpose Grease

75 400

0.5

220

280

-15

-20 to +160

280

Lithium complex

Grey

2

504-701

EP-2 Moly

ALBIDA LC

GREASES 3.74.06

6.9

GREASES Alvania EP D Grease Railroad Bearing Grease

3.61.03

A premium EP long life railroad journal roller bearing grease. Recommended Applications: • Heavily loaded locomotive and rolling stock wheel bearings Advantages: • Excellent rust and oxidation resistance • Outstanding oxidation stability and high wear resistance in heavily loaded applications • Extended trouble free service and long shelf life Approvals: • Association of American Railroads (AAR) Specification M-942-98 Properties

ALVANIA EP D

NLGI Grades

1.5

Product Code

504-534

Colour Dropping Point, °C Thickener

Brown 180 Lithium/Calcium Soap


173

4 Ball EP, Weld Load

250

6.10

GREASES

6.11

GREASES Alvania EP - Premium Multi-Purpose Grease

3.14.14

“New and improved”, premium multi-purpose, extreme pressure (EP), lithium soap based greases. Recommended Applications: • Multi-purpose, heavy duty automotive, industrial and marine applications • Pins and bushings, plain and rolling element bearings • Including chassis points, universal joints, water pumps, track rollers, clutches and wheel bearings • -50°C to 130°C temperature range • Arctic grades are designed for low temperature central systems • MS (Multi-Season) grades for low temperature grease gun applications • Moly versions should be used for sliding applications such as steering gears, king pins, front suspensions, fifth wheels, guide ways and booms; EP Arctic Moly for trailer central lube systems Advantages: • Improved oxidation stability • Improved mechanical stability • EP for excellent load carrying ability • Compatible with most other greases • Excellent rust protection • Resists water washout Approvals: • Approved for the requirements of CFIA (Canadian Food Inspection Agency),Type n1, for general use; avoid food contamination during application and storage.

6.12

0.5

250

-25 to 135

-20

4 Ball EP, Weld Load, kg


Min. Dispensing Temp, °C (may vary with dispensing system)

Timken OK Load, kg

4 Ball Wear, mm

150

18.2


200

Lithium soap

Dropping Point, °C

Thickener Type

Brown

504-532

Product Code

Colour

2

EP 2

NLGI Grade

Product

Properties

-25

-30 to 135

250

0.5

18.2

150

200

Lithium soap

Brown

504-531

1

EP 1

-45

-50 to 80

200

0.6

18.2

20

190

Lithium soap

Brown

504-509

0

EP Arctic

-45

-50 to 80

250

0.6

18.2

20

190

Lithium soap

Grey

504-514

0

EP Arctic Moly

Grey

504-511

1

EP MS Moly

-35

-40 to 80

250

0.6

18.2

27

195

-35

-40 to 80

250

0.6

18.2

27

195

Lithium soap Lithium soap

Brown

504-513

1

EP MS

Alvania EP - Premium Multi-Purpose Grease

-20

-25 to 135

250

0.5

18.2

150

200

Lithium soap

Grey

504-518

2

EP Moly

ALVANIA EP

GREASES 3.14.14

6.13

GREASES Alvania Grease 2 - Non-EP Grease

3.78.02

A premium non-EP version of the lithium soap based Alvania grease line. Recommended Applications: • Plain and rolling bearings where extreme pressure additives are not required. • Where low noise performance is required Advantages: • Excellent rust and oxidation resistance • Additives selected to ensure low noise in rolling element bearings

Properties

ALVANIA GREASE 2

NLGI Grade

2

Product Code

504-522

Colour Thickener Type

Amber Lithium soap

Dropping Point, °C

200


48

Base Oil Viscosity Index

97


6.14

-25 to 130

GREASES Cardura - Rail Curve Lubricants

3.81.03

Two year-round rail-curve greases. Recommended Applications: • Curved sections of railway track serviced by track-side rail lubricators • Cardura Plus for steep grades and high curvature applications which may generate higher wheel temperatures Advantages: • Retention on tracks • Pumpability / mobility to ensure application at low temperatures • All-season performance, proven at temperatures from -40°C to + 40°C • Reduced rail / wheel wear and maintenance • Potential for improved fuel economy • Excellent track coverage - over 5 km with “WS”, 10 km with “Plus” Note: Please consult your Shell Product Specialist to determine proper lubricator design Properties Product

CARDURA WS

PLUS

NLGI Grade

1

1

Product Code

504-506

504-508

Black

Black

Solid Additives

Graphite / Moly

Graphite

Thickener Type

Calcium

Microgel

Dropping Point, °C

142

260+


17.4

22.0

-40 to +80

-35 to +80

460 (20) 650 (29) 770 (34) 1,100 (49) 1,800 (80)

---1,850 (88) 3,800 (168)

Colour

Est. Operating Range, °C Low Temp. Pumpability‡ , Pressure Drop, kPa /m (psi /ft) @ @ @ @ @

0°C -10°C -20°C -30°C -40°C

‡ Pressure drop in 3/16 inch OD tubing @ shear rate of 1 sec-1.

6.15

GREASES Shell FM Grease 1.5 - Food Grade Grease

3.48.04

Multi-purpose “food approved” grease. Recommended Applications: • Lubrication of machinery in food processing and canning industries where the grease which is used can contaminate the food being processed • For use in canneries, beverage bottling plants, candy plants, meat and fish packing plants etc. • Suitable for year-round and refrigeration applications • For a food grade lubricating oil, see Shell FM Grease 1.5 Advantages: • Multi-purpose • Non-toxic • Excellent resistance to water washout • Protects equipment against water, juices, acids and other process fluids • Rust and oxidation inhibited • Superior wear and load carrying capacity • Excellent high temperature performance • 1.5 grade for maximum dispensability in indoor centralized systems Approvals: • Satisfies the requirements of U.S. Department of Agriculture (USDA), FDA,Type H1 (incidental food contact)

Properties

SHELL FM GREASE 1.5

NLGI Grade

1.5

Product Code

504-811


White Aluminum complex

Dropping Point, °C

246

Base Oil Viscosity, cSt @ 40°C

67.0

Viscosity Index

85


250

Water Washout, % loss @ 38°C

6.16

2

GREASES Cyprina RA - Electric Motor Bearing Grease

3.57.08

A premium, non-EP, lithium soap based grease. Recommended Applications: • Rolling bearings in traction motors of GM Electromotive Diesels (EMD) and GE Electric locomotives • Conventional electric motor bearings including “lifetime” sealfor-life units • Suitable for temperatures up to 135°C Advantages: • Superior mechanical stability for long life • Long oxidation life • Grease hardness suitable for electric motor bearings Approvals: • Recommended for EMD and GE locomotive electric motor bearings • Recommended for Westinghouse electric motor bearings

Properties

CYPRINA RA GREASE

NLGI Grade

3

Product Code

504-538

Colour Thickener Type Dropping Point, C

Amber Lithium Soap 195


-30 to 135

Base Oil Viscosity @ 40°C

93

6.17

GREASES Darina AX General Purpose Wheel Bearing Grease

1.13.05

A premium, non EP, multi-purpose automotive wheel bearing grease. Recommended Applications: • Automotive chassis parts • Wheel bearings Advantages: • High temperature protection, dropping point above 250°C • Long life • Rust and corrosion inhibited • Resistance to water washout • High mechanical stability Approvals: • Meets the requirements of NLGI GB-LB

Properties

DARINA AX

NLGI Grade

1.5

Product Code

510-032

Colour Thickener Type Dropping Point, °C Base Oil Viscosity, cSt 40°C Base Oil Viscosity Index Est. Operating Range, °C

6.18

Tan Microgel None (+250°C) 171 92 -30 to 150

GREASES

6.19

GREASES Darina XL - Premium Multipurpose Greases 3.75.11 Premium multi-purpose, extreme pressure (EP), non-lead, microgel based greases. Includes synthetic base oil, moly and multi-season versions. Recommended Applications: • Multi-purpose industrial and automotive • Where extreme temperatures and shock loading are encountered • Including conveyors and pug mills of asphalt plants, ball mills of ore crushing • Wheel bearings and chassis points Advantages: • Synthetic XL 102M provides year round protection even at extremely low and high temperatures • “ColourSense” indicator - grease changes colour from its original blue as the temperature rises above 120°C. Colour changes thru green , then to brown and finally to orange as the temperature of the application rises. Useful to indicate possible faulty equipment, excessively high temperatures and a need for more frequent regreasing. • Superior high temperature performance and oxidation resistance • Excellent load carrying ability • Excellent low temperature dispensability from the entire XL family of greases • Compatibility with most other types of greases (thickeners) • Outstanding water resistance • Temperature range from -45 to 170°C Approvals: • Darina XL greases meet NLGI GC/LB wheel bearing and chassis requirements • Approved for the requirements of CFIA (Canadian Food Inspection Agency),Type n1, for general use; avoid food contamination during application and storage.

6.20

70

-45 to 170

4 Ball EP, Load Wear Index


-40

0.6


100

4 Ball Wear Scar, mm

Synthetic

260+

Microgel


Base Oil Type

Dropping Point, °C

Thickener Type

Grey

504-574

Product Code

Colour

1

NLGI Grade

-10

-20 to 160

60

0.5

170

Mineral

260+

Microgel

Blue

504-554

2

-10

-20 to 160

60

0.5

170

Mineral

260+

Microgel

Grey

504-555

2

EP Moly

EP 2

Products

102M (Moly)

DARINA XL GREASES

Properties

-35

-40 to 80

55

0.5

21

Mineral

260+

Microgel

Blue

504-556

1

Multi-Season

GREASES

Darina XL - Premium Multipurpose Greases 3.75.11

6.21

GREASES Diamond Drill Rod Grease - Drill Rod Lubricant A grease for reducing rotating friction between drill rods and casings. Recommended Applications: • Outside of drilling rods, prior to insertion into the hole Advantages: • Reduces friction and horsepower requirements • Increases drilling efficiency • Contains a germicidal agent to prevent infection of cuts which may occur during handling of the drill rods

Properties

DIAMOND DRILL ROD

NLGI Grade

3

Product Code

504-971


Amber Barium Sodium Complex


118

Dropping Point, °C

196

4 Ball EP, Load Wear Index Est. Operating Range, °C

6.22

42 -20 to + 120

GREASES Dursol K1 - Sour Gas Valve Grease

3.60.02

Dursol K1 grease is designed to lubricate and protect valves in the oil and gas resources industry which are exposed to corrosive sour natural gas and oil. Recommended Applications: • Valve bodies and stems of valves in sour (H2S containing) natural gas pipeline and gas plant service Advantages: • H2S corrosion protection • Base oils selected for year round low temperature valve operation

Properties NLGI Grade Product Code Colour Thickener Type Dropping Point, C Base Oil Viscosity, cSt 40°C Est. Operating Range, °C

DURSOL K1 GREASE 1 504-630 Light green Microgel 260+ 20 -30 to 120

6.23

GREASES Malleus GL - Heavy Duty Open Gear Lubricant 3.84.04 A non-asphaltic, lead-free open gear lubricant which does not contain any environmentally offensive solvents. Recommended Applications: • Open gears as primarily found on mining shovels, draglines and grinding mills • Malleus GL 25 may be used in certain enclosed gear cases propel transmissions, final drive gear boxes and hoist gear cases on mining shovels • Plain and anti-friction bearings, pins and bushings on shovel crawlers and boom assemblies • Shovel sticks, swing gears, crowd pinions and racks, roller paths • Malleus GL-95 is also available in an aerosol spray can Advantages: • Synthetic and paraffinic base oils utilized to optimize performance • Lead free • May be applied manually or via an automatic lube system • Malleus GL improves equipment availability and saves on maintenance costs because it: • Stays soft and pliable to eliminate root build-up • Is fortified with molybdenum disulphide (Moly) and other solid lubricants for a proper film structure with good antiwear, EP, load carrying and shock loading protection • Passes FZG +13 load stages • Minimizes cold metal contact welding • Resists contamination from other oils • Alleviates “stick slip” vibrations • Reduces consumption rates Approvals: • Recognized for use by B.E., Marion, P&H,Allis Chalmers • Qualifies as P&H Multi-Service Mining Lubricant

6.24

-40

* Available in aerosol spray can, Product Code 504-688.

Est. Low Temp. Dispensing, °C

+ 2045

500 75

Falex Continuous Load Failure, kg

0.5

-2,400 13,750

Apparent Viscosity, cP -1°C -18°C -40°C

4 Ball EP Weld Load, kg Load Wear Index

1,675 550

Apparent Viscosity, cP 40°C 100°C

4 Ball Wear Scar Diameter, mm

420+

Worked Penetration @ 25°C (60x)

1.003

00 \ 000

Approx. NLGI grade

504-672

25

Density @ 15.6∞C

Product Code

Grades

Properties

-30

+2045

620 85

0.6

-6,600 39,000

2,250 1,325

420+

00 \ 000

1.070

504-676

65

-10

+2045

800 110

0.7

-9,400 --

6,125 4,000

420+

00 \ 000

1.076

504-680

95*

205

0

+2045

800 120

0.7

-20,500 --

7,300 6,100

420+

00 \ 000

1.080

504-684

MALLEUS GL

+7

+2045

800 131

0.7

7,900 16,000 --

7,060 1,375

418

00

1.090

504-685

300

+10

+2045

800 166

0.7

-12,500 --

36,750 3,825

370

0

1.090

504-669

400

GREASES

Malleus GL - Heavy Duty Open Gear Lubricant 3.84.04

6.25

GREASES Malleus TC - High Pressure Thread Compound 3.63.04 Lead free high pressure thread compound to aid in joining and separating threaded connections. Recommended Applications: • Casing and tubing connections in the oil and gas industry • Metallic tubulars with A.P.I. 8 Round, LTC and EUE thread profiles • Other general threading applications Advantages: • Lead free for health and safety protection • Superior H2S corrosion inhibitors • Protects against seizures or galling (adhesion) of the threaded contact surfaces • Thread sealing pressure tested to 7,500 PSI • Ease of application for year round usage Approvals: • Meets or exceeds A.P.I. Bulletin 5A2 Properties Product Code Colour Specific Gravity

MALLEUS TC 504-598 Silver \ Grey 1.629

Composition

55 % solids

Penetration @ 25°C

312 - 332

NLGI grade Dropping Point of Base, °C

1 299

API Brushing Ability Applicable at, °C

-23

Torque Correction Factor

0.95

6.26

GREASES Ossagol C Moly - Semi Fluid Grease

3.49.07

A semi-fluid, non EP, Moly grease for centralized lubrication systems. Recommended Applications: • Railway locomotive wheel flange and rail lubrication via onboard lubricators • Lightly loaded gear boxes requiring a semi-fluid grease. Also see Shell Surstay EP 000 • Centralized lubrication systems operating at low temperatures • Including trucks, buses, manufacturing machinery Advantages: • Rust and oxidation inhibited • Excellent low temperature pumpability / mobility • Water resistant • Carries well along railway rails Approvals: • Meets the requirements of Canadian National Railways,Willy Vogel Properties

OSSAGOL C MOLY

NLGI Grade

00

Product Code

504-512


Grey Calcium Soap

Dropping Point, °C

137


27

Est. Operating Range, °C (may vary with dispensing system) Mobility @ -30°C, g/min

-40 to 80 114

6.27

GREASES Retinax TL 00 - Trailer Wheel and Hub Lubricant A premium, synthetic, semi-fluid, EP grease for truck wheel hubs. Recommended Applications: • Truck wheel hubs / trailer wheel bearings • Leaky gearboxes or gear units that are difficult to service. Verify that the base oil viscosity is appropriate. • Guidelines for use in wheel hubs can be found in The Maintenance Council (TMC) practice RP 631 Advantages: • Synthetic base oil provides good low temperature pumping in centralized systems, compared to mineral oil of similar viscosity • Significantly reduces leakage relative to gear oil • Heavy base oil viscosity and EP additives provide wear and shock loading protection • Provides rust protection and excellent oxidation stability • Natural tacky nature toward metal surfaces

Properties

RETINAX TL 00

NLGI Grade

0 / 00

Product Code

504-820

Appearance

Red

Thickener Type

Lithium Complex

Base Oil Viscosity, cSt 40°C 100°C

460 41.5

Timken OK Load, kg

22.7

4 Ball EP Weld Load, kg Load Wear Index, kg

250 46

Est. Operating Range, °C Short Exposure, Max., °C

6.28

-40 to 170 230

GREASES

6.29

GREASES SRS 2000 - Water Resistant Grease Our most water resistant, multi-purpose grease for use in heavy duty applications. Recommended Applications: • Heavy duty on and off highway equipment • Logging, construction, agricultural and forestry equipment • Car washes • Marine applications • Fifth wheels, pins, bushings, slack adjusters, chassis points, pulley bearings, couplings,“cups and saucers” Advantages: • Outstanding heavy duty water resistant protection • Synthetic and other high performance components • Moly and low temperature winter versions • Protects against vibration and shock loading • Outstanding mechanical stability • Excellent adhesion (tackiness) • Superior oxidation resistance provides long performance life Approvals: • Approved for the requirements of CFIA (Canadian Food Inspection Agency),Type n1, for general use; avoid food contamination during application and storage.

6.30

510-333

36.4

0.4

400

Timken OK Load, kg

4 Ball Wear, mm


0

3

Min Dispensing Temp, °C

Water Washout Test, % wt loss

-15 to 135

171 400 27.7

Est. Operating Range, °C (may vary with dispensing system)

183

Base Oil Viscosity, cSt 40°C Blended 40°C Extracted 100°C Extracted

Lithium/Calcium

Dropping Point, °C

Thickener

Tacky / Grey

Product Code

Appearance / Colour

2

Summer Moly (5%)

NLGI Grade

Product

Properties

5

0

-15 to 135

315

0.5

18.2

171 600 37.2

183

Lithium/Calcium

Tacky / Red

510-332

1.5

Summer

510-334

1

Winter

10

-35

-40 to 80

315

0.5

18.2

29 35 5.4

178

Lithium/Calcium

Tacky / Red

SRS 2000

10

-35

-40 to 80

400

0.4

22.7

29 35 5.4

178

Lithium/Calcium

Tacky / Grey

510-335

1

Winter Moly (5%)

GREASES

SRS 2000 - Water Resistant Grease

6.31

GREASES Surstay EP - Semi Fluid Grease

3.67.02

A semi-fluid, EP grease for enclosed heavy-duty gear box applications. Recommended Applications: • Rotor drive gear boxes of Marietta Miners in potash mining • Drive gear boxes of conveyor systems • Gear boxes where leaking bearing seals make the use of a thickened oil desirable • NOT recommended for centralized lubrication pumping systems. In these applications, Ossagol *C Moly or Alvania EP Arctic are recommended. Advantages: • Extreme pressure, antiwear and shock loading protection • Excellent stability - maintains thickness without thinning or thickening • Tenaciously adheres to gear and bearing surfaces to prevent dry start-up • Excellent seal compatibility

Properties

SURSTAY EP 000

NLGI Grade

000

Product Code

504-988


Brown Microgel

Dropping Point, °C

260+


184

4 Ball Wear, mm

0.5

4 Ball EP, Weld Load, kg Load Wear Index

250 47


6.32

-10 to 130

GREASES Ultragel - High Temperature Grease

3.58.04

A synthetic grease for extremely high temperatures. Recommended Applications: • Plain and rolling element bearings • Run-out table rolling bearings in steel mills • In mines, mills, boiler plants • In pulp and paper, saw mills • In cement and lime plants • NOT suitable for high speed or low temperature applications due to the high viscosity base oil used • Prior to use, bearings should be thoroughly cleaned of conventional greases Advantages: • Outstanding high temperature resistance • Suitable up to 250°C with frequent relubrication • Superior mechanical stability against high shears and pressures

Properties NLGI Grade Product Code Appearance / Colour Thickener Type

ULTRAGEL 2 504-560 Very Tacky/Amber (clear) Inorganic

Dropping Point, °C

+343


7,500

Timken OK Load, kg

27.2

Max. Operating Temperature, °C

250


+20

6.33

6.34

INDUSTRIAL OILS Table of Contents Page Biodegradable (Hydraulic Oils) Shell Naturelle HF-E . . . . . . . . . . . . . . . . . . . . . . . . . . . Shell Naturelle HF-M . . . . . . . . . . . . . . . . . . . . . . . . . .

7.32 7.33

Compounded Valvata . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.60

Compressor Air:

7.16 7.12 7.10 7.18 7.14 7.6 7.7 7.8

Electrical Diala . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.22

Food Grade Shell Fluid FM 32 . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.3

Form (Concrete) Form Oil 46 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.25

Flushing Cassis A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.4

Gear Omala . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Geartherm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Omala HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Omala RL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tivela. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hyperia S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.38 7.27 7.40 7.41 7.53 7.28

Heat Transfer Thermia C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.52

Hydraulic / Circulating Tellus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tellus T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tellus HD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tellus 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Decol H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Morlina . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No Fire WG 200R. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shell FR-N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VSI 68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.46 7.50 7.48 7.45 7.19 7.30 7.36 7.34 7.62

Natural Gas: Refrigeration:

7.1

INDUSTRIAL OILS

Corena P . . . . . . . . . . . . . . . . . . . . . . Corena DE . . . . . . . . . . . . . . . . . . . . . Corena AS . . . . . . . . . . . . . . . . . . . . . . Corena S. . . . . . . . . . . . . . . . . . . . . . . Corena NG . . . . . . . . . . . . . . . . . . . . . Clavus . . . . . . . . . . . . . . . . . . . . . . . . Clavus AB . . . . . . . . . . . . . . . . . . . . . . Clavus HFC 68 . . . . . . . . . . . . . . . . . .

INDUSTRIAL OILS Table of Contents, continued Page Machine Tool Tonna V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.54

Metalworking / Cutting Oils Dromus B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Garia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.24 7.26

Mineral Oils Vitrea 22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.61 Pella A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.42 Shellflex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2, 9.4 Natural Gas Engine Mysella . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.31

Non-Drip Stringol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.44

Paper Machine Delima. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Delima R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.20 7.21

Refrigeration - see Compressor Rock Drill Torcula . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.56

Rust Preventative VSI 68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.62

Sawguide Sawguide Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solvent Shell Indusol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.43 7.29

Spindle Tellus 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.45

Turbine Shell Turbo T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.58

White Oil - see Food Grade Wire Rope Classlube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.2

7.5

INDUSTRIAL OILS Shell Fluid FM 32 - Food Grade White Oil

3.25.09

A mineral based white oil for use in food processing equipment. Recommended Applications: • Mold release oil in bakery applications • Carrier in cosmetics and medicinal products • Food essences and flavouring substitutes • General purpose lubricant for applications where the lubricant may directly contact food being processed Advantages: • Multi-purpose - a white oil suitable as a lubricant as well as a food and cosmetic ingredient Approvals: • Satisfies the requirements of U.S. Department of Agriculture (USDA), FDA,Type H1 (incidental food contact) • Pass United States Pharmacopoeia (USP) specification • Approved for the requirements of the Canadian Food Inspection Agency (CFIA),Type n3 (protective coating oils), for registered meat packaging plants • 3-GP-46A • 3-GP-46M

Properties Grades Product Code

SHELL FLUID FM 32 407-961

Colour, Saybolt

+30


37

Pour Point, °C

-6

Flash Point, °C

188

Aniline Point, °C

105

7.3

INDUSTRIAL OILS Cassis Oil A - Flushing Oil

3.24.07

A mineral oil-based product for flushing / cleaning the internal components of equipment and machinery. Recommended Applications: • Flushing circulation systems, gearboxes and other equipment to remove rust preventatives, dirt, construction debris and water prior to service or in older equipment which simply requires cleaning • Including paper machines, marine, and manufacturing plants • Cassis A should be properly disposed after the flushing procedure • Caution - Cassis A will attack and/or remove some paints Advantages: • Select base oils and solvents • Rust inhibited • Highly solvent flushing oil • Penetrating action • Safe at elevated temperatures (60 - 70°C) used for best flushing Approvals: • Meets MIL-C-15348A Amendment 2 • Meets 3-GP-354A

Properties Grades

CASSIS A 32

Product Code

407-950


28.0 4.6

Pour Point, °C

-33

Flash Point, °C

132

TAN - C

0.2

7.4

INDUSTRIAL OILS Classlube - Cable and Wire Rope Lubricant Shell Classlubes are free flowing oils, fully blended to inhibit rust, oxidation and wear. Recommended Applications: • Wire Rope Lubricants on friction hoist ropes • Any type of conveyor, chain drives • Applications where ‘tacky’ oils are required Advantages: • Free flowing oils blended from HVI base stocks • Formulated to inhibit oxidation and wear • Unique dual anti-rust additive system provides extra rust protection under corrosive conditions • Fortified with a tackifier to provide adhesion of the lubricant to wire ropes, chains, conveyors • ISO 32 grade available in aerosol cans for ease of application • Dyed red for easy identification

Properties Grades

CLASSLUBE 32

320

Product Code

407-201

407-203

Appearance

Tacky

Tacky

Colour

Red

Red

Viscosity, mm2/s 40°C 100°C

32 5.8

315 25

Viscosity Index

124

102

Pour Point, °C max.

-27

-15

Rust (Syn. Sea Water)

Pass

Pass

4-Ball Wear Test Scar diameter, mm

0.50

0.41

7.5

INDUSTRIAL OILS Clavus Oil - Refrigeration Compressor Oil Mineral oil based refrigeration compressor oil. Recommended Applications: • Refrigeration compressor oil • Suitable for, and compatible with CFC (Freon* 12, Freon* 22 etc.) and ammonia refrigerant gases with evaporator temperatures down to -45°C • NOT recommended for use with newer HFC gases such as R-134A and R-23 Advantages: • Wax free, naphthenic base oils (low floc point) provide outstanding low temperature performance • Oxidation stability at high temperatures resists deposit formation • Excellent chemical stability and compatibility Approvals: • Meets or exceeds the requirements of most compressor builders

Properties Grades

CLAVUS OIL 68

Product Code

407-942


55.0 5.88

Pour Point, °C max

-35

Floc Point, °C

-45

Flash Point, °C

179

Aniline Point, °C

88

Dielectric Strength, KV

30

7.6

3.95.01

INDUSTRIAL OILS Clavus AB Synthetic Refrigeration Compressor Oils

3.96.03

Synthetic refrigeration compressor oils for conventional low temperature refrigerants. Recommended Applications: • All refrigeration compressor types including reciprocating, centrifugal and rotary • Compatible with ammonia, CFC and HCFC refrigerant gases with evaporator temperatures below -45°C • Including R12, R13, R22, R114, R123, R124, R401A, R401B, R401C, R402A, R402B, R403, R500, R502, R503 refrigerants in both industrial and marine applications • NOT recommended with HFC gas R-134A. See Shell Clavus HFC 68. Advantages: • Special alkylated synthetic base stocks • Extended service life and longer drain intervals • Outstanding low temperature properties - no deposit formation • Excellent high temperature stability • Eliminates degradation and sludging • Prevents fouling of heat transfer surfaces, evaporators and valves • Improved wear protection • Compatible with conventional mineral oils and materials such as Mylar*, polypropylene,Viton*, Buna-N, Neoprene*, and nylon elastomers • Improved compressor efficiency • High degree of chemical stability • Improved resistance to foaming Properties Grades

CLAVUS AB OILS 32

68

Product Code

407-681

407-682


33 4.1

65 5.6

Pour Point, °C

-45

-35

Floc Point, °C

-65

-55

Flash Point, °C

150

165

Dielectric Strength, KV

30

30

7.7

INDUSTRIAL OILS Clavus HFC 68 Synthetic Refrigeration Compressor Oils

3.97.02

Synthetic refrigeration compressor oils for newer HFC (chlorine free, environmentally friendly) refrigerants such as R-134A, as well as for conventional CFC or Freon* based refrigerants. Recommended Applications: • Automotive air conditioning and industrial and mobile refrigeration units with compressors that are designed for, or have been converted to using R-134A, HFC refrigerants • Compressors using CFC or Freon* refrigerants as well as blended HFC refrigerants Advantages: • No miscibility problems with R134A refrigerants • Suitable for plants with both new and older refrigerants in use and wishing to consolidate lubricants • Compatible with mineral oils, although mixing will adversely affect performance • Compatible with elastomers of Buna-N, NBR-AcrylonitrileButadiene, HNBR-Hydrogenated Acrylonitrile-Butadiene (Nitrile content >32%),Viton* and Teflon* • Suitable over a wide temperature range, -57°C to +66°C • Improved lubricity • Excellent stability • Reduced compressor wear • Increased hydrolytic stability in the presence of water

Properties

CLAVUS HFC 68

Grades

68

Product Code

407-683


68 8.6

Pour Point, °C

-54

Flash Point, °C

248

TAN

0.02

Critical Solution Temp, °C R-12 R-22 R134A R404A

7.8

< < < <

-56.7 -56.7 -56.7 -56.7

INDUSTRIAL OILS

7.9

INDUSTRIAL OILS Corena AS - Synthetic Air Compressor Oil

3.98.01

A high performance synthetic lubricant for oil-flooded vane and screw air compressors. Recommended Applications: • Rotary oil-flooded vane and screw type air compressors • Heavy duty, single or multi-stage equipment operating with high discharge temperatures operating at high or low ambient temperatures • Reciprocating air compressors should use Shell Corena DE (synthetic) or Shell Corena P (mineral oil) Restrictions in Use: • Shell Corena AS should not be used in reciprocating compressors, or in drip-feed rotary compressors which have different lubrication requirements and compressors used for breathing air. Advantages: • Will reduce maintenance costs over operation on conventional mineral oils • Utilizes synthetic PAO (poly-alpha-olefin / synthetic hydrocarbon) base oils • Long oil life - up to eight times that of mineral oils • Ultimate performance beyond the scope of mineral based oils • Low volatility - less oil consumption and make-up required • Resistance to oxidation and the deposits it creates • Good low temperature performance • Excellent demulsibility • Compatible with mineral oils and common oil seal materials Approvals: • Approved for the requirements of the CFIA (Canadian Food Inspection Agency),Type n1, for general use; avoid food contamination during application and storage.

7.10

INDUSTRIAL OILS Corena AS - Synthetic Air Compressor Oil Properties Grades

3.98.01

CORENA AS 46

68

Product Code

407-943

407-944


42.3 7.3

69.5 12.4

Viscosity Index

136

180

1,470 4,500

2,200 6,500

-54

-45

Low Temp. Viscosity, cSt -18°C -29°C Pour Point, °C Flash Point, °C

277

260

Fire Point, °C

307

277

Autoignition Point, °C CCR residue, %

400

400

< 0.01

<0.01

7.11

INDUSTRIAL OILS Corena DE - Synthetic Air Compressor Oil

3.99.01

Formerly Corena AP oils.A high performance diester synthetic oil for reciprocating air compressors. Recommended Applications: • Stationary or mobile reciprocating air compressors • Heavy duty, single or multi-stage equipment operating with high discharge pressures (over 30 bar, 435 psi) and high discharge temperatures (over 180°C) • Compressors operating at high or low ambient temperatures • May be used to compress air for breathing purposes provided strict conditions are adhered to - including proper subsidiary air clean-up apparatus downstream of compressor* • New equipment run-in (first 1,000 hours) should use Shell Corena P Oils • Rotary air compressors should use Shell Corena AS (synthetic) or Shell Tellus Oil (mineral) *Restrictions in Use: • This product should not be used in non-diaphragm compressors that produce breathing air unless the outlet air is monitored continuously for CO.These lubricants can produce CO when subjected to high temperatures. Advantages: • Safety - greatly reduces the danger of fires and explosions which can occur from deposits caused by mineral based oils • Ultimate performance beyond the scope of mineral based oils • Resistance to oxidation and the deposits it creates • Will reduce maintenance costs over conventional mineral oils, extending valve maintenance intervals 4 - 8 times • Low volatility - less oil consumption and make-up required • Good low temperature performance • Good demulsibility • Compatible with Viton*, fluorosilicone, polysulfide and high nitrile Buna-N elastomers • Not compatible with Neoprene*, natural rubber, SBR styrenebutadiene rubber (Buna-S) or low nitrile Buna-N seals, polycarbonate filter bowls, some paint

7.12

INDUSTRIAL OILS Corena DE - Synthetic Air Compressor Oil Properties Grades

3.99.01

CORENA DE 68

100

Product Code

407-684

407-680


68.3 8.9

98.8 9.7

Low Temp. Viscosity, cSt -18°C

9,085

32,530

Pour Point, °C

-42

-33

Flash Point, °C

266

266

Fire Point, °C

288

288

Autoignition Point, °C

410

410

CCR residue, %

0.04

0.01

7.13

INDUSTRIAL OILS Corena NG - Reciprocating Compressor Cylinder and Packing Oil

3.71.04

Premium, partially synthetic, cylinder and packing oil primarily for sour and/or wet natural gas reciprocating compressors. Recommended Applications: • Applied via oil injection systems into cylinders and packings of reciprocating compressors in sour (H2S) and wet (water or hydrocarbon) service • 220 grade provides protection in cylinders with discharge pressures up to 14,000 kPa (2,000 PSI) • 460 grade provides protection in cylinders with discharge pressures up to and beyond 28,000 kPa (4,000 PSI) • Propane compression with suction temperatures down to -30°C • Compressing chemical gases such as aldehydes and keytones • For compressor crankcases of this type use Shell Mysella Oils Advantages: • Non-fatty formulation eliminates deposits in the injection system • Not sensitive to freezing • Superior low temperature flow properties • Resistant to wash-off from cylinder walls in wet service • Excellent oxidation resistance and valve/rod cleanliness • Corrosion protection against H2S and rusting from water Approvals: • Meets requirements of Dresser Rand, Cooper Energy Services and others

Properties Grades

CORENA NG 220

460

Product Code

407-238

407-239


211 17.9

422 28.4

Pour Point, °C

-24

-18

4,300 13,800 27,400

12,000 ---

Est. Lowest Suction Temp, °C

-30

-15

Flash Point, °C

268

282

Brookfield Viscosity, cP 0°C -10°C -15°C

7.14

INDUSTRIAL OILS

7.15

INDUSTRIAL OILS Corena P - Air Compressor Lubricants

3.79.03

Mineral oil based air compressor oils for reciprocating compressors Recommended Applications: • Industrial and marine reciprocating air compressors • Including single and multistage units with trunk or crosshead piston designs • Including crankcases of oil-free designs • Including cylinder oils for machines with separate oil injection systems • Suitable for discharge temperatures of 160°C and up to 200°C • Corena P oils should never be used in equipment compressing pure oxygen Restrictions in Use: • This product should not be used in non-diaphragm compressors that produce breathing air unless the outlet air is monitored continuously for CO.These lubricants can produce CO when subjected to high temperatures. Advantages: • Selected base stocks for exceptional resistance to deposit formation • Safety from fires and explosions caused by deposit formation • Reduced equipment maintenance • 122 grade replaces both ISO 100 and 150 • Compatibility with seals, other mineral based oils and some synthetics • Rust and corrosion protection • Anti-wear protection • Good demulsibility from water • Performance rivals synthetic oils in all but the most severe applications without the problems of seal compatibility, cylinder wear, corrosion and odour associated with some synthetics Approvals: • Meets ISO-L-DAB (medium duty service at temperatures between 140°C and 160°C) • Recommended for Atlas Copco, Compair, Broomwade and Reavell, Ingersol Rand and others

7.16

INDUSTRIAL OILS Corena P - Air Compressor Lubricants Properties Grades

3.79.03

CORENA P 68

122

220

Product Code

407-226

407-240

407-230


69 8.2

123 11.7

220 18.2

Viscosity Index

83

80

91

Pour Point, °C

-33

-27

-15

Flash Point, °C

228

230

292

Fire Point, °C

262

278

318

7.17

INDUSTRIAL OILS Corena S - Premium R & O Compressor Oil Corena S is a mineral oil based, rust and oxidation (R&O) inhibited oil. Recommended Applications: • Rotary screw and vane compressors requiring a rust and oxidation inhibited oil in an ISO 32 grade • Circulating systems requiring an R&O oil • Hydraulic systems requiring an R&O type oil (low pressure) • Plain and rolling element bearings in pump crankcases • For heavier viscosity grades see Shell Morlina Oils Advantages: • Outstanding oxidation resistance • Specially processed and handled to enhance water separation and air release • Excellent rust protection Approvals: • Meets Cincinnati Milacron P-38 specification for “Rust and Oxidation Inhibited Hydraulic Oils”

Properties Grades

CORENA S 32

Product Code

407-225


32 5.4

Viscosity Index

102

Pour Point, °C

-30

7.18

INDUSTRIAL OILS Decol H - General Purpose Hydraulic Oils

3.64.07

General purpose anti-wear hydraulic oils. Recommended Applications: • Industrial and mobile hydraulics • Suitable for all types of hydraulic pumps • Circulating systems in place of R&O type oils • For high performance state-of-the-art hydraulic systems, Shell Tellus and Tellus T Oils are recommended Advantages: • Cost effective performance • Wear protection • Long oil life • Rust and oxidation inhibited Approvals: • Meets Vickers 104C vane pump test pass • Meets Vickers 35VQ25 vane pump test pass • Meets Denison P46 axial piston pump test pass

Properties Grades

DECOL H 22

32

46

68

Product Code

407-736

407-737

407-738

407-739


20.8 4.27

31.9 5.4

46.3 6.8

68.5 8.8

Viscosity Index

99

100

98

100

Pour Point, °C

-27

-27

-24

-24

Flash Point, °C

210

217

238

247

7.19

INDUSTRIAL OILS Delima - Paper Machine Oil

3.05.10

A leading edge technology, detergent-dispersant type paper machine oil. Intended to set the standard for the industry. Recommended Applications: • Paper machine oil circulation systems, dry and wet ends, as well as individually lubricated bearings • Including high speed newsprint machines, high temperature kraft and board machines • Including rolling and Kingsbury type bearings, centrifugal pumps, vacuum and water pumps, blowers, reduction gears, main drive shaft winder and rewinders etc. Advantages: • Rapid water separation from “white water” • New detergent technology • Filterability when contaminated with water, Passes Pall test • Mild EP and wear protection, passes FZG load stage 12 • High temperature and oxidation stability • Rust and corrosion protection • Resistance to foaming Properties Grades

DELIMA OILS 150

220

290

460

Product Code

407-821

407-823

407-825

407-826


151 15.0

220 18.9

290 22.9

457 30.6

Viscosity Index

94

96

96

95

Pour Point, °C

-18

-15

-12

-12

Flash Point, °C

265

288

288

292

7.20

INDUSTRIAL OILS Delima R - Sunds Defibrator Refiner Oil

3.06.01

A unique premium oil for Sunds defibrator refiners as used in the pulp and paper industry. Recommended Applications: • Sunds defibrator refiner lubrication Advantages: • Excellent extreme pressure and anti-wear protection • Prevents erosion on the piston by the seals and subsequent oil leakage • Excellent water separation and performance in the presence of water • Good filterability performance designed to result in cleaner systems and lower filter costs • Designed to effectively release air and dispel foam • Excellent corrosion protection for the steel and bronze components used in Sunds refiners. Passes SKF Roller Bearing Test with no discolouration of the rollers. Approvals: • Approved for use by Sunds Defibrators Properties Grades

DELIMA R 68 68

Product Code

407-828


69 8.7

Viscosity Index

97

Pour Point, °C

-30

Flash Point, °C

242

4 Ball EP, Weld Load (kg)

305

4 Ball EP, OK Load (kg)

285

7.21

INDUSTRIAL OILS Diala - Electrical Insulating Oils

3.17.05

Naphthenic electrical insulating oils, with and without antioxidant additives. Recommended Applications: • Transformers, circuit breakers, oil-filled switches, X-ray equipment • Capacitors (condensers) and oil insulated cables • Heat transfer medium • Spindle oil in high speed bearings • Diala A for Class B,Type I applications (non-anti-oxidant) • Diala AX for Class B,Type II applications (which require an anti-oxidant) Advantages: • Excellent electric insulation and heat transfer properties • Do not contain any polychlorinated biphenyls (PCB’s) • Low pour point • Oxidation stability to resist acid formation • Diala Oils are specially handled and packaged to prevent minute contamination by moisture, particulate, fibres and surfactants. Storage should be indoors, in air-tight containers, in a climate-controlled environment Approvals: • Meets ANSI / ASTM D-3487 • Meets NEMA TR-P8-1975 • GE spec A13A3A2 (10CA) • Westinghouse PD 55822 AV rev.T-WEMCO CI • US Military spec VV-I-530a and Amendment 2 for Class I (Type I)and Class II (Type II) fluids. Supersedes Dept of Navy spec OS-1023. • NATO symbol S-756, covered by British Standard BS 148:1972 • Diala AX is approved for the requirements of CFIA (Canadian Food Inspection Agency),Type n1, for general use; avoid food contamination during application and storage.

7.22

INDUSTRIAL OILS Diala - Electrical Insulating Oils Properties Grades

3.17.05 DIALA OILS Diala A / AX

Product Code

407-652 / 407-651

Viscosity, cSt 0°C 40°C 100°C

66 9.3 2.6

Pour Point, °C

-47 to -55

Flash Point, (COC) °C

155

Interfacial Tension @ 25°C, Dynes/cm

47

Dielectric Strength @ 60 Hz: DISC electrodes, Kv VDE electrodes (1.02 mm gap), Kv

51 34

Power Factor, % @ 100°C Aniline Point, °C TAN-C Gassing Tendency µL/min.

0.03/0.04 76 < 0.01 12

7.23

INDUSTRIAL OILS Dromus B - Soluble Cutting Oil

3.11.08

Premium soluble oil for making oil-in-water emulsions used in cutting / metalworking operations. Recommended Applications: • Cutting applications where cooling is essential to the operation • Sawing, plain milling and grinding operations • Boring and turning of some steels • Quenching induction heated parts • Roll coolant • As a corrosion inhibitor in hydraulic systems where water is the hydraulic fluid • Should NOT be used on metals containing magnesium • See our “Lubricants Report” for preparation and fluid maintenance instructions. Dromus B is sensitive to “freezethaw” exposure, please store appropriately. Advantages: • Built-in biocide • Excellent rust protection • Better aluminum compatibility due to lower pH • Outstanding freeze/thaw stability • No chemical, toxicological or irritation hazards

Properties Product Code

DROMUS B 407-776


80

Base Oil Flash Point, °C

162

pH (10% Emulsion)

8.7

7.24

INDUSTRIAL OILS Form Oil 46 - Concrete Form Release Agent 3.47.04 Release agent for wooden concrete construction forms. Recommended Applications: • Specifically designed for wooden forms used in concrete pouring operations • Also suitable for metal and plastic forms used in concrete construction • Sprayed, swabbed, or brushed onto forms • May be cut-back with kerosene as required. 10% kerosene is a good initial mix Advantages: • Mineral and fatty oils provide easy release of the wood from the concrete • Smooth quality surface finish on concrete • Reduced wear and prolonged form life Properties Grade

FORM OIL 46 46

Product Code

407-632


45 6.1

Viscosity Index

72

Pour Point, °C

-30

Flash Point, °C

164

TAN-E

5.6

7.25

INDUSTRIAL OILS Garia - Neat Cutting Oils

3.08.01

Two “Active” sulphur and chlorine containing, EP cutting / metalworking oils for ferrous metals which are moderate to difficult to machine. Recommended Applications: • Garia D for multi-spindle work, gear cutting, thread grinding, tapping and threading, thread rolling and broaching of high tensile steels and stainless and heat resistant alloys • Garia T for Deep-hole Boring / Drilling using various Systems, high-speed hobbing gear shaping, broaching and for use with skiving and roller burnish tooling systems of low, medium and high tensile steels and stain resistant and heat resistant alloys • NOT recommended for machining “yellow” metals • NOT to be used as a hydraulic medium • Plain milling, sawing and grinding operations should use Shell Dromus B soluble cutting oil Advantages: • Active EP type additive system provides improved cutting efficiency, better surface finish and tool life • Viscosity selected to lubricate the cutting interface and wash away chips. Garia D’s viscosity is designed to reduce “dragout” while Garia T is designed for precision grinding • Garia T does not lose its active ingredients or form sludge under severe filtration (10 micron) required for deep hole applications • Garia D may stain non-ferrous and yellow metals • NOT to be mixed with water to form cutting emulsions

Properties

GARIA

Product

Garia D

Garia T

Product Code

407-801

407-798


32 4.7

15 2.9

‡

‡

Pour Point, °C Flash Point (COC), °C Min

160

127

Sulphur Content, % mass

0.89

1.04

Chlorine Content, % mass

0.92

4.1

‡ Do Not Store Below 0°C

7.26

INDUSTRIAL OILS Geartherm Oils - Premium All-season Industrial Gear Oils

3.65.07

Mineral based, multigraded industrial gear oils. Geartherm Oils are all-season (low temperature, multigrade) versions of Shell Omala Oils. Recommended Applications: • Enclosed industrial gearboxes which may be started or operated in cold environments • Rolling bearings in pump crankcases Advantages: • Year-round performance • AGMA EP - excellent load carrying ability and protection against shock loading • “Stay-in-Grade” viscosity performance • Improved rust and corrosion protection • Anti-foam protection • Good water separation capability • For a full synthetic industrial gear oil see Shell Omala HD Oils Approvals: • Hydro Quebec PAEM 89204 Properties Products

GEARTHERM Arctic AS

Multigrade 150

ISO Grade

68

150

AGMA Grade

2EP

4EP

Product Code

407-537

407-539


64.3 9.84

151 18.7

Viscosity Index

135

140

-17,083 38,500 150,000

19,300 62,985 143,167 --

Brookfield Visc., cP -20°C -26°C -30°C -36°C Pour Point, °C

-39

-33

Flash Point, °C

174

216

< -50

-45

-36 to 45

-30 to 70

Channel Point, °C Max. Typical Oil Operating Range, °C

7.27

INDUSTRIAL OILS Hyperia S - Synthetic Industrial Gear Oil

3.80.04

A full synthetic industrial EP gear oil. Recommended Applications: • Specifically for General Electric wheel motors • For a full line of full synthetic industrial EP gear oils see Shell Omala HD Advantages: • Full synthetic (PAO) base oils for excellent low temperature properties in a heavy ISO 220 gear oil. • Improved equipment reliability and reduced equipment operating costs • Energy savings from improved efficiency Approvals: • GE 787 and GE 788 for motorized wheels Properties

HYPERIA S

Grades

220

AGMA Grade

5 EP

Product Code

407-523


222 26.0

Viscosity Index

162

Brookfield Viscosity, cP @ -38°C Pour Point, °C Channel Point, °C Flash Point, °C

7.28

150,000 -48 < -50 263

INDUSTRIAL OILS Shell Indusol - Industrial Hydrocarbon Solvent

5.08.02

A conventional mineral spirits industrial solvent. Recommended Applications: • Cleaner • Diluent • Degreaser • Agent in surface coatings, waxes and polishes Advantages: • Interchangeable with all Stoddard solvents • Traditional solvency and evaporation rate • Available in 205 litre drums Approvals: • CAN 2-3.8-M85 • ASTM D-235-77 • 1-GP-4M Ref 12080-M • P-D-680 AM.2 Type 1 • TT-T-291e AM.1 Type 1 GrA Properties Product Code

SHELL INDUSOL 482-100

Density

786

Flash Point, °C (Tag CC), min.

42

Aniline Point, °C

55

Kauri Butanol Value

39

Distillation Range, °C Sulphur Content, mg/kg (ppm)

158 - 193.5 <1

7.29

INDUSTRIAL OILS Morlina - R & O Circulating Oil

3.12.02

Premium, medium / high viscosity rust and oxidation oils for circulating systems. Recommended Applications: • Circulating systems requiring heavier viscosity rust and oxidation oils • Hydraulics, gears and bearings where a thicker, non-EP, non-anti-wear oil is required. Systems not prone to wear, high loads or shock loading • Gear systems with internal backstops where anti-wear/ EP additives can cause equipment (conveyors) to creep under load • For lower viscosity grades see Shell Turbo T Oils Advantages: • High rust and oxidation resistance • Superior demulsibility from water • Low foaming tendency Approvals: • Recommended or approved for use by Alpha Laval, Falk, Danielli • Approved for the requirements of CFIA (Canadian Food Inspection Agency),Type n1, for general use; avoid food contamination during application and storage.

Properties Grades

MORLINA 150

220

320

Product Code

407-881

407-882

407-883


152 14.9

220 18.9

316 24

97

97

97

Viscosity Index Pour Point, °C

-18

-12

-12

Flash Point, °C

283

290

306

7.30

INDUSTRIAL OILS Mysella - Premium Natural Gas Engine Oils 3.72.03 Recommended Applications: • Stationary natural gas engine oils • Mysella 40 is an ashless oil for 2 stroke engines • Mysella LA30 and LA 15W-40 are low ash oils for 4 stroke engines • Mysella MA40 is a medium ash oil intended for most Waukesha and White Superior engines • See our “Lubrication Report” for specific application details • Also used in natural gas compressor crankcases • Cylinders and packings in dry and sweet gas service • Most pump crankcases Advantages: • Three ash levels • Ashless (and low ash) blended to reduce port blockage • Premium anti-wear, rust and oxidation and detergency additives • Compatible with NSCR catalysts • Improved nitration resistance • Multigrade for improved low temperature start-ups Approvals: • Mysella LA30, LA 15W-40 and MA40 meet API CD • Mysella MA40 approved for Waukesha Cogeneration applications

Properties Grades

MYSELLA 40

LA30

LA15W-40

MA40

Product Code

407-177

407-173

407-176

407-174


139 13.1

110 12.2

108 14.3

147 14.8

Sulphated Ash, %

0.01

0.45

0.45

0.80

TBN-E

1.1

5.2

5.2

7.7

Pour Point, °C

-18

-27

-33

-30

7.31

INDUSTRIAL OILS Shell Naturelle HF-E Synthetic Biodegradable Hydraulic Oil Synthetic ester based, biodegradable hydraulic oils. Recommended Applications: • Hydraulic and power transmission systems where leakage could mix with the soil or water • Hydraulics on heavy duty construction and earth moving equipment • Machine tool hydraulics • General industrial control systems • Hydrostatic drive gears • Moderately loaded gears where an anti-wear hydraulic oil is specified • Where DIN 51524 Part 2 or Part 3 (HLP/HVLP) anti-wear petroleum oil is specified • Bulk operating temperature should not exceed 90°C Advantages: • Readily biodegradable • Excellent viscosity/ temperature characteristics, high VI • “Stay-in-grade” shear stability • Excellent corrosion protection • Good oxidation resistance • Wear protection under severe duty situations • Compatible with mineral oils, insoluble in water Approvals: • Meets requirements of Caterpillar BF-1biodegradable hydraulic fluids Properties

SHELL NATURELLE HF-E

Grades

32

46

Product Code

407-210

407-211


31.6 6.3

46.1 9.1

Viscosity Index

156

182

Pour Point, °C

-60

-51

Flash Point (COC), °C

236

219

7.32

INDUSTRIAL OILS Shell Naturelle HF-M - Biodegradable Hydraulic Oil Biodegradable anti-wear hydraulic oil based on a mixture of synthetic ester and vegetable oil. Recommended Applications: • Suitable for the majority of hydraulic applications • Including axial piston and vane pumps • Mining, mobile forestry equipment where leakage could mix with soil or water • Oil in the hydraulic system must be kept free from water, <1000 ppm • Recommended operating temperature range -25°C to +70°C Advantages: • High degree of biodegradability • Contains a significant amount of renewable resource • Stable viscosity at -20°C • Reduced tendency to form sticky deposits when accidentally spilled • Excellent lubricity • Excellent anti-wear protection Approvals: • Vickers V-104C Pass • Vickers 35VQ25 (M-2952-S) Pass

Properties

SHELL NATURELLE HF-M

Grade

46

Product Code

407-214

Viscosity, mm /s 40°C 100°C

42.6 9.6

Viscosity Index

220

Pour Point, °C

-39

Rust (Distilled Water)

Pass

FZG, failure load stage

>12

2

7.33

INDUSTRIAL OILS Shell FR-N - High Performance, Less Flammable Hydraulic Fluid

3.89.02

Factory Mutual approved as a less hazardous fluid. Shell FR-N Oil is an ISO Class HFDU anhydrous less flammable hydraulic fluid. Recommended Applications: • Typical applications are in the metal, mining and glass industries. • Hydraulic installations; it provides good lubrication and a higher degree of fire resistance. Advantages: • Less flammable - greater fire resistance to that provided by conventional mineral oils • Cost effective performance - in most plant hydraulic applications and is very cost competitive when compared to polyol esters • Fully compatible with mineral hydraulic oils. No major modification of the hydraulic circuit is necessary • Wear protection and lubricity - meets the anti-wear requirements of virtually all vane pumps (where this property is most important). • When maintained properly, the fluid can provide equivalent or better vane pump performance than many mineral-based hydraulics. • Provides satisfactory service in most piston and gear pumps. Passes FZG load stage 12, demonstrating excellent load carrying ability. • Long oil life - in most applications due to its oxidation inhibition. For optimum life, system-operating temperatures should not exceed 60-65 °C for extended periods. • Fluid maintenance - to maximize fluid life, water contamination should be avoided. • High degree of biodegradability - Contains a significant amount of a renewable resource • High Viscosity Index - Minimal change of viscosity over wide range of operating temperatures • Seal Compatibility - compatible with all seal materials and paints normally specified for use with petroleum mineral oils except those made from natural rubber. Recommended elastomers include NBR, Fluorocarbon, Fluorosilicone, and Polyacrylate. Approvals: • Eaton Vickers 104C & 35VQ25 performance • Denison T6C vane pump performance

7.34

INDUSTRIAL OILS Shell FR-N - High Performance, Less Flammable Hydraulic Fluid Properties Grades

3.89.02 SHELL FR-N OIL

46

48

Product Code

407-676

407-674

Appearance

Clear light amber

Clear light amber

Viscosity, cSt (mm2/s) mm2/s at 40°C mm2/s at 100°C

47 9.2

69 13.9

Viscosity Index

202

>200

Pour Point, °C

-21

-18

Flash Point, COC, °C

234

260

7.35

INDUSTRIAL OILS “No Fire” WG 200R - Water Glycol Fire Resistant Hydraulic Fluid

3.90.00

A premium, general purpose water glycol fire resistant hydraulic fluid. Recommended Applications: • Where hydraulic piping may rupture and spray hydraulic fluid onto hot surfaces, where mineral based fluids can ignite and cause a severe hazard • Precision industrial and mobile hydraulic systems up to 2,000 psi @ 50°C. Higher pressures (3,000 psi) and temperatures may be possible • Underground mining applications • Where Group 1 Factory Mutual or CANMET fluids are required Advantages: • Excellent fire resistance • Good anti-wear characteristics, protection against pump and component wear • Inherently low pour point and excellent viscosity/ temperature characteristics • Liquid and vapour phase corrosion inhibited to protect ferrous and non-ferrous components • Readily biodegradable, low ecotoxicity, reduced environmental liability • Non-WHMIS controlled, low toxicity Approvals: • Factory Mutual Group 1 approved • CANMET - CAN3-M423-M84 approved for use in underground mines For information on hydraulic design considerations and maintenance of Water Glycol fluids, contact Shell Canada’s Help Centre. Properties Grades

NO FIRE WG 200R 46

Product Code

407-670

Appearance

Clear Red


44

Water Content, % m

39

PH

9.5

Pour Point, max. °C

-50

7.36

INDUSTRIAL OILS

7.37

INDUSTRIAL OILS Omala - Premium EP Gear Oils

3.10.15

A mineral oil based full industrial extreme pressure enclosed gear oil. Omala Oils are designed to protect gearing against high loads / shock loading, and for use in oil mist systems. Recommended Applications: • Enclosed industrial gears including worm gears • Rolling bearings in pump crankcases • Oil mist (oil fog) applications Advantages: • Full industrial EP • Excellent load carrying properties protect against shock loading and prevent scuffing and galling (adhesion) • Outstanding foam performance • Outstanding water separation • FZG, 12th stage load pass • Rust and oxidation inhibited • Excellent sludge and oxidation control • Withstand continuous operating temperatures up to 93°C • Non corrosive to yellow metals up to moderate temperatures • Little or no free fog release in condensing mist units • Lead and Chlorine free Approvals: • Meets or Exceeds US Steel 224 for lead free EP gear oil • Meets or Exceeds AGMA 250.04 • Meets Hydro Quebec PAEM 89204 • Meets or Exceeds DIN 51517 Part 3 • Meets or Exceeds requirements for David Brown gear boxes • Approved by Cincinnati Milacron (selected grades) • Omala 1000 meets Marion GL-250 • Approved for the requirements of CFIA (Canadian Food Inspection Agency),Type n1, for general use; avoid food contamination during application and storage.

7.38

97

242

27.5

Flash Point, °C

Timken OK Load Typical (Kg.)

67.5 8.58


-30

407-528

Product Code

Pour Point, °C

EP2

AGMA No.

Viscosity Index

68

Grades

Properties

27.5

250

-24

98

100.0 11.3

407-527

EP3

100

27.5

256

-24

98

149.7 14.8

407-529

EP4

150

31.8

258

-18

96

233 19.6

EP6

320

27.5

250

-12

96

322.6 24.3

407-533

OMALA

407-531

EP5

220

27.5

260

-12

96

465.1 30.8

407-534

EP7

460

29.5

238

-9

86

690.9 36.3

407-532

EP8

680

31.8

238

0

87

997 46

407-535

EP8A

1000

INDUSTRIAL OILS

Omala - Premium EP Gear Oils 3.10.15

7.39

INDUSTRIAL OILS Omala Oils HD - Synthetic Industrial Gear Oils

3.19.01

Premium, Extreme Pressure, synthetic industrial gear and bearing oils. Recommended Applications: • Enclosed industrial gears including worm gears that require an EP gear oil • “Lubricated-for-life” systems • Gear boxes operating at elevated temperatures • Rolling bearings in pump crankcases Advantages: • Fully synthetic (PAO, Synthetic hydrocarbon) base stocks • Compatible with seals and paints used with mineral oils • Full industrial EP additive system • Performance superior to conventional mineral based industrial gear oils • Reduced oil change frequency • Increased equipment reliability, life and operational efficiency • Improved load carrying properties protect against shock loading and prevent scuffing and galling (adhesion) • Low traction coefficients, reduced energy consumption • Improved system cleanliness, oxidation resistance • Improved low temperature characteristics • Outstanding foam performance • Outstanding water separation • FZG, 12th stage load pass • Rust inhibited, non-corrosive to yellow metals up to moderate temperatures Approvals: • Meets the requirements of major gear box manufacturers • Approved for the requirements of CFIA (Canadian Food Inspection Agency),Type n1, for general use; avoid food contamination during application and storage. Properties Grades

OMALA OILS HD 100

220

460

680

Product Code

407-546

407-541

407-542

407-543


100 15.0

222.4 25.8

458.3 45.5

668 62.6

Viscosity Index

157

148

155

164

Pour Point, °C

-48

-48

-42

-39

Flash Point, °C

252

245

240

236

4Ball EP (Weld), kg

290

290

290

290

7.40

INDUSTRIAL OILS Omala Oils RL - Synthetic Industrial Gear Oils

3.04.01

Premium, non-EP, synthetic industrial gear and bearing oils. Recommended Applications: • Lightly loaded, enclosed industrial gears subjected to severe operating conditions and NOT requiring an EP gear oil • “Sealed-for-life” systems • Gear boxes operating at elevated temperatures • Moderately loaded rolling bearings in pump crankcases • Oil circulation systems • Marine separators • For synthetic “EP” gear oils see Shell Omala Oils HD Advantages: • Fully synthetic (PAO, Synthetic hydrocarbon) base stocks • Compatible with seals and paints used with mineral oils • Performance superior to conventional mineral based industrial gear oils • Longer oil life, longer component life • Increased equipment reliability, life and operational efficiency • Low traction coefficients: reduced energy consumption • Improved system cleanliness: oxidation and thermal resistance • Improved low temperature characteristics • Outstanding foam performance • Outstanding water separation • FZG, 12th stage load pass • Rust inhibited, non-corrosive to yellow metals up to moderate temperatures • Worm gear reducers (460 grade) Approvals: • Approved for the requirements of CFIA (Canadian Food Inspection Agency),Type n1, for general use; avoid food contamination during application and storage. Properties Grades

OMALA OILS RL 150

220

460

Product Code

407-548

407-544

407-545


153 19.8

222 25.9

458 45.5

Viscosity Index

149

149

155

Pour Point, °C

-54

-48

-42

Flash Point, °C

236

240

274

4Ball EP (Weld), kg

210

210

210 7.41

INDUSTRIAL OILS Pella A - Low Viscosity Mineral Oil

3.30.06

A low viscosity straight mineral oil. Recommended Applications: • Diluent for heavy duty metalworking oils • Coolant / lubricant for diamond tipped saws, for cutting stones and ceramics, and for machining non-ferrous metals and alloys • Cutting fluid in lapidary applications, eye glass lens grinding • Calibration fluid for diesel injectors • Water-proofing paper Advantages: • Very low viscosity • Nearly odourless • Nearly transparent in colour Approvals: • Meets FDA as an Aluminum Rolling Lubricant Properties

PELLA A

Product Code

407-790


4.43

Pour Point, max °C

0


136

Flash Point (TAG), °C

>98

Fire Point, °C

150

Aniline Point, °C

87

Distillation Range, °C

7.42

274 - 326

INDUSTRIAL OILS Sawguide Oil - Saw Mill Sawguide Lubricant Lubricant to reduce friction between the guide surfaces and the saw face. Recommended Applications: • Sawguide applications in sawmills • Linear or rotating guideways • Low or high surface speeds, light or heavily loaded • Chains Advantages: • Allows for higher accuracy and better surface finish of lumber • Tacky nature provides non-drip property • Anti-wear provides protection against scoring and wear of equipment subject to heavy loads • Separates readily from water • Corrosion protection Properties Grade

SAWGUIDE 220

Product Code

407-504

Appearance

Tacky


217.1

Viscosity Index

99

Pour Point, °C

-18

Flash Point, °C

248

TAN

0.41

7.43

INDUSTRIAL OILS Stringol - Non Drip Oil

3.07.07

Tacky, general purpose “non-spattering” lubricating oils that reduce drippage and staining. Recommended Applications: • General purpose, light duty rapidly moving parts • Once-through applications • Textile industry in leaky comb boxes, looms, saddle and top rolls, loosely fitting sleeve bearings • Saw mill chains, light duty gears and cams, sleeve bearings • Metal working, printing, container manufacture, wood working machines etc. Advantages: • Heavy, tacky nature reduces dripping and improves metal adhesion over straight mineral oils • Reduced consumption and throw-off • Non staining

Properties Grades

STRINGOL B

D

Product Code

407-811

407-813

Appearance

Tacky

Tacky


99.1 12.3

262 21.6

Viscosity Index

95

95

Pour Point, °C

-21

-12

Flash Point, °C

214

220

TAN-C

0.1

0.1

7.44

INDUSTRIAL OILS Tellus 10 - Spindle Oil

3.01.14

A low viscosity, mineral oil based rust and oxidation oil. Recommended Applications: • High speed spindle bearing applications which do not require an anti-wear oil as found on textile machines and other machine tools • Hydraulic systems that do not require anti-wear type oils • Airline lubricators in pneumatic systems • Any light duty, general lubrication application requiring a very light mineral oil Advantages: • Utilizes special base stocks • Rust and oxidation inhibited • Superb water separation characteristics • Very low foaming tendency Properties Grade

TELLUS 10 10

Product Code

407-160


9.7 2.4

Viscosity Index

34

Pour Point, °C

-57

Flash Point, °C

152

7.45

INDUSTRIAL OILS Tellus - Premium Hydraulic and Circulating Oils

3.01.14

A premium mineral oil based, anti-wear hydraulic oil. New and improved. Recommended Applications: • All hydraulic systems requiring an anti-wear oil • Oil circulating systems including those recommending R&O oils, where it is desirable to rationalize that number of oils being used • Plain and rolling element bearings in pump crankcases, some electric motor bearings etc. • Gear sets requiring non-EP gear oils • Steam turbines should use Shell Turbo T Oils • Low temperature applications should use Shell Tellus T Oils • Tellus Oils should not be used in pumps containing silver plated components Advantages: • Excellent wear protection, for use in all pump types at all pressure levels • Advanced oxidation stability • Improved wet filterability as demonstrated in Denison T6C vane pump test • Hydrolytic stability protects against degradation in the presence of water • Improved tolerance to contamination • Improved frictional characteristics • Excellent water separation • Excellent air release properties • Silicone-free Approvals: • Denison HF-O, HF-2 • Passes Denison T6C vane pump test • Meets Vickers* M-2952-S • Passes Vickers* 35VQ25 vane pump test • Passes Vickers* 104C vane pump test • Cincinnati Machine P-68, P-69, P-70 • Approved for the requirements of CFIA (Canadian Food Inspection Agency),Type n2 (hydraulic oil); avoid food contamination during application and storage. * Eaton Vickers

7.46

407-161

21.6 4.23

99

-36

208


Viscosity Index

Pour Point, °C

Flash Point, °C

22

Product Code

Grades

Properties

212

-33

108

32.2 5.52

407-162

32

220

-30

106

46.3 6.94

407-163

46

236

-27

103

68.2 8.88

407-164

68

TELLUS OILS

254

-27

100

96.7 11.0

407-165

100

286

-24

97

147 14.6

407-166

150

INDUSTRIAL OILS

Tellus - Premium Hydraulic and Circulating Oils 3.01.14

7.47

INDUSTRIAL OILS Tellus HD - Synthetic Hydraulic Oils

3.15.01

Premium, synthetic, anti-wear hydraulic oils. Recommended Applications: • All hydraulic systems requiring an anti-wear oil that operate at extremely low or high temperatures, beyond the capabilities of mineral based oils • Including excavators, cranes, shovels, drills, crawlers,“cherry pickers” • Portable compressors • Plain and rolling element bearings, gears not requiring an EP oil and circulation systems exposed to extreme temperatures • Tellus HD Oils should not be used in pumps containing silver plated components • For mineral based low temperature hydraulic oils see Shell Tellus T Oils Advantages: • Uses PAO (Synthetic hydrocarbon) base oils • Compatible with seal materials and other mineral oils • High natural Viscosity Index, low natural pour points • Long Life - resists oxidation at high temperatures • Excellent wear protection, for use in all pump types at all pressure levels • Thermally stable at extreme loads and temperatures • Hydrolytic stability protects against degradation in the presence of water • Rapid air release without foaming • Long term rust and corrosion protection • Excellent water separation Approvals: • Denison HF-O • Meets Vickers M-2950-S and I-286-S • Passes Vickers 35VQ25 and 104C vane pump tests • 22 Grade - Approved for Bucyrus Erie 49RZ & 59R Blast Hole Drills

7.48

INDUSTRIAL OILS Tellus HD - Synthetic Hydraulic Oils Properties Grades

3.15.01

TELLUS HD OILS 22

46

Product Code

407-131

407-133

Viscosity, cSt - 40°C + 40°C 100°C

2754 21.44 5.04

11,685 45.36 8.48

Brookfield Viscosity, cP - 40°C

2,520

10,879

174

167


-68

-62

Flash Point, °C

172

220

Fire Point, °C

192

256

7.49

INDUSTRIAL OILS Tellus T Oils - Premium All-Season Hydraulic Oils

3.13.12

Tellus T Oils are all-season (low temperature, multigrade) versions of Shell Tellus Oils. New and improved. Recommended Applications: • Year-round use in all mobile and stationary hydraulic systems requiring an anti-wear oil that operate outdoors or have flow lines that are exposed to low temperatures • Including excavators, cranes, shovels, drills, crawlers,“cherry pickers” • Saw mills, woodlands operations and snow removal equipment • Portable compressors • Circulating systems including those servicing plain and rolling element bearings in pump crankcases and some electric motor bearings etc. and gear sets requiring non-EP gear oils where temperatures vary seasonally • Tellus T Oils should not be used in pumps containing silver plated components Advantages: • Improved low temperature fluidity to reduce non-productive warm-up time, minimize energy losses and reduce pump cavitation • All-season protection • Excellent resistance to viscosity breakdown (shear) • Premium anti-wear protection, for use in all pump types at all pressures • Advanced oxidation and thermal stability against high heat • Improved wet filterability as demonstrated in Denison T6C vane pump test • Improved tolerance to contamination • Improved frictional characteristics • Excellent air release properties • Silicone-free Approvals: • Denison HF-O, HF-2 • Passes Denison T6C vane pump test • Meets Vickers* M-2950-S • Pass Vickers* 35VQ25 vane pump test • Pass Vickers* 1-286-S • Cincinnati Machine P-68, P-69, P-70 • Approved for the requirements of CFIA (Canadian Food Inspection Agency),Type n2 (hydraulic oil); avoid food contamination during application and storage. *Eaton Vickers 7.50

190

274 856 2,908 5,856

-57

114

Viscosity Index

Brookfield, cP -20°C -30°C -40°C -45°C

Pour Point, °C

Flash Point, °C

-47 to 44

15.2 4.1

-39 to 56

166

-51

680 2,567 11,480 25,236

163

22.7 5.1

407-157

T22

-32 to 67

212

-45

1,483 6,735 32,086 80,101

156

32.0 6.4

407-159

T32

TELLUS T OILS

-27 to 78

226

-42

3,081 14,091 93,465 --

145

45.9 7.95

407-179

T46

-21 to 87

252

-36

40,613 ---

7,400

133

67.7 10.1

407-169

T68

Tellus T Oils - Premium All-Season Hydraulic Oils

Max. Typical Oil Operating Range, °C

407-154


T15

Product Code

Grades

Properties

INDUSTRIAL OILS 3.13.12

7.51

INDUSTRIAL OILS Thermia C - Heat Transfer Oil

3.21.11

A mineral based, heat transfer oil. Recommended Applications: • For use in indirect fired heat transfer systems • Particle board mills, sawmills, asphalt plants • In closed systems, up to 290°C for continuous operation, 315°C for intermittent periods Advantages: • Oxidation inhibitor package protects the base oil from deterioration • Excellent resistance to thermal cracking • Low vapour pressure • Rust inhibited to prevent corrosion • Low temperature start-ups to - 5°C for centrifugal oil pumps and - 7°C for gear pumps Properties ISO Grades

THERMIA C 68

Product Code

407-640


64 8.2

Viscosity Index

96

Pour Point, °C Flash Point (COC), °C Flash Point (PMCC), °C TAN-C

7.52

-6 260 210 0.005

INDUSTRIAL OILS Tivela - Synthetic Industrial Gear Oils

3.31.02

A non-EP, polyglycol (PAG) synthetic industrial gear oil. Recommended Applications: • Worm gears • High temperature gear applications - beyond the 93°C limit of conventional mineral EP gear oils and the 120°C limit of synthetic EP gear oils • Suitable for all types of gears including spur, bevel and planetary units • Gear applications where natural load carrying and efficient power transmission are required • Seal-for-life gear boxes not requiring an EP gear oil • NOT compatible with mineral based products • NOT compatible with many paints • Neutral effect on most sealing materials • Shell Tivela Oils are not recommended for the lubrication of gears manufactured from bronze alloys containing aluminum • Where industrial EP oils are required see Shell Omala, Omala HD or Shell Geartherm Advantages: • Polyglycol base oil has very high viscosity index, low pour point, high natural load carrying capacity and low frictional characteristics • Oxidation stability provides long life for seal-for-life gear boxes • Very good high and low temperature properties • Optimal power transmission • Especially suited for steel and bronze gear tooth interaction as found in worm gears Approvals: • Recommended by David Brown, SEW and NORD Gear Properties

TIVELA

Product

WB

SD

ISO Grades

220

460

Product Code

407-521

407-522


254.5 39.2

467 76

Viscosity Index Typical Operating Range, °C FZG 12th Load Stage

208

200

-30 to +170

-20 to +170

Pass

Pass

7.53

INDUSTRIAL OILS Tonna V - Slide Way Lubricant

3.55.04

Lubricant designed to reduce static friction of guide surfaces of table ways. Recommended Applications: • Machine tool ways, slides and guides • Horizontal and vertical ways, flat or “V” shaped • Linear or rotating guideways • Low or high surface speeds, light or heavily loaded • Including grinders, milling machines, planers, saw guides, workheads, work tables, lathe saddles, overhead machinery, conveyors • Chains • Central oil systems that supply both the slide ways and hydraulic system should use Tonna V 68. • Bearings and ways of punch presses should use Tonna V 220 to protect equipment from the inherent shock loading • NOT to be used where the oil may contact textile materials Advantages: • No jerky start-up motion. Low “Stick-Slip” values. Ratio of static friction to kinetic friction is less than 0.8 • Allows for higher accuracy and better surface finish of the work piece • Tacky nature provides non-drip property for vertical and overhead ways • Anti-wear provides protection against scoring and wear of equipment subject to heavy loads • Separates readily from water • Corrosion protection Approvals: • Cincinnati Milacron P-47, P-50 and P-53 Properties Grades

TONNA V 32

68

220

Product Code

407-506

407-507

407-508

Appearance

Tacky

Tacky

Tacky


32

68.2

217.1

Viscosity Index

110

104

99

Pour Point, °C

-36

-30

-18

Flash Point, °C

206

234

248

TAN

0.49

0.49

0.41

7.54

INDUSTRIAL OILS

7.55

INDUSTRIAL OILS Torcula - Pneumatic Rockdrill Oils

3.53.05

Premium, high performance lubricant for air operated percussion tools. Recommended Applications: • Rockdrills, jackhammers • In mining, road building, construction etc. • Independent rotation or rifle bar drills Advantages: • Superior wear protection • Controlled atomization and misting • Resistance to dieseling or spontaneous ignition and the associated heat • Prevents formation of hard carbonaceous deposits • Exceptional low temperature fluidity for wear protection and atomization at low temperatures • Emulsifies with water to carry water through the drill • Rust inhibited

7.56

46 8.8

171

-45

180

208


Viscosity Index

Pour Point, °C

Flash Point, °C

Fire Point, °C

-30 to + 15

Tacky

Ambient Temperature Operating Range, °C

407-855

Appearance

46

Product Code

Grades

Properties

-10 to + 20

292

242

-27

113

68 9.3

Tacky

407-852

68

100

-5 to + 30

308

254

-24

105

101 11.7

Tacky

407-853

TORCULA

Above + 10

318

272

-18

103

150 15.3

Tacky

407-854

150

Above + 15

328

282

-15

101

227 20

Tacky

407-850

220

INDUSTRIAL OILS

Torcula - Pneumatic Rockdrill Oils 3.53.05

7.57

INDUSTRIAL OILS Shell Turbo T Oils - Premium Turbine Oils

3.03.08

Shell Turbo T Oils are mineral oil based, rust and oxidation (R&O) inhibited oils. Recommended Applications: • Steam, water and hydraulic turbines in industrial and marine use • Stationary, frame type gas turbines requiring a mineral oil lubricant • Circulating systems requiring R&O oils • Hydraulic systems requiring an R&O type oil (low pressure) • AGMA rust and oxidation inhibited gear lubricants (non-EP) • Plain and rolling element bearings in pump crankcases • For heavier viscosity grades see Shell Morlina Oils Advantages: • Outstanding oxidation resistance • Specially processed and handled to enhance water separation and air release • Excellent rust protection Approvals: • Meets Hydro Quebec PAEM 89201 • Meets Ontario Hydro M-332M-B5 • Meets General Electric GEK-32568C • Meets Westinghouse 551125 AC • Shell Turbo T32 meets ASEA Brown Boveri (ABB) spec VTI3200-3/1994/03 • Meet Cincinnati Milacron “Rust and Oxidation Inhibited Hydraulic Oils” CM spec P-38 Shell Turbo T 32 CM spec P-54 Shell Turbo T 68 CM spec P-55 Shell Turbo T 46 • Approved by the CFIA (Canadian Food Inspection Agency) for industrial food plant use • Approved for the requirements of CFIA (Canadian Food Inspection Agency),Type n1, for general use; avoid food contamination during application and storage.

7.58

-30

Pour Point, °C

+9,000

102

Viscosity Index

Turbine Oil Stability Test, hr.

32 5.4


+6,500

-27

101

46 6.8

407-953

+6,500

-27

100

67 8.6

407-954

68

46

32

407-952

Grades

Product Code

SHELL TURBO T OILS

Properties 78

+6,500

-24

101

78.6 9.68

407-955

100

+6,500

-24

100

99 11.4

407-956

INDUSTRIAL OILS

Shell Turbo T Oils - Premium Turbine Oils 3.03.08

7.59

INDUSTRIAL OILS Valvata - Compounded Oils

3.35.09

Mineral based, high viscosity, compounded steam cylinder oils. Recommended Applications: • Steam cylinders • Gears (especially worm gears) and bearings at low speeds and moderate loads, with either bath or pressure circulation systems • Some multi-stage reciprocating compressor cylinders and packings • NOT suitable for hypoid gears • NOT suitable for application below freezing where additive stability may be affected Advantages: • Excellent stability • Excellent lubricity associated with classic fatty compounded oils Properties Grades

VALVATA J 460

K 680

Product Code

407-320

407-323


444 30.0

640 37.3

96

94


-9

-6

Flash Point, °C min

334

340

TAN-C

0.17

0.29

Saponification Number

10.3

18.5

7.60

INDUSTRIAL OILS Vitrea 22 - General Purpose Mineral Oil

3.18.08

A highly refined paraffinic mineral lubricating oil. Recommended Applications: • Oil lubricators and central lubrication systems • Lubricating plain and rolling bearings • Spur, helical and bevel gears where an oil which does not contain additives is adequate • Where gear tooth and bearing loads are not extreme • Moderate temperature applications Advantages: • Natural high viscosity index and low pour points • Readily separates from water • Low cost • Good oxidation stability Properties Grade

VITREA 22

Product Code

407-421


20.3 4.02

Viscosity Index

95

Pour Point, °C

-18


196

TAN-C

0.01

7.61

INDUSTRIAL OILS VSI Oil - Circulating and Rust Inhibiting Oil

3.43.04

Mineral based circulating oil specially formulated to provide Vapour Space (rust) Inhibition. Recommended Applications: • For protecting internal, enclosed equipment components from rusting both above and below the oil level during equipment idle periods or intermittent use or during shipment • Also a general purpose rust and oxidation circulating oil • All enclosed oil lubrication systems where rusting may occur due to steam condensate or atmospheric moisture such as oil storage tanks, reservoirs, rolling bearing and gear housings, pump crankcases, machine tool housings • Run-in of new equipment and subsequent shipping. VSI 68 may be easily drained and replaced with the operating lubricant if a different oil is required • Steam turbine systems where corrosion on tank walls and overheads is occurring • Recommended for oil temperatures below 65°C and definitely below 95°C for the VSI inhibitor to be effective • Metal surfaces to be protected should be within 6 feet of the surface of the oil • NOT recommended for open systems or surface exposed to the weather • See our Lubricants Report for application details Advantages: • Contains a volatile corrosion inhibitor which adsorbs to metal surfaces in the enclosed space above the level of the oil in the system • Excellent oxidation stability • Superior demulsibility from water • Resistant to foaming Properties Grade

VSI OIL 68 68

Product Code

407-880


68.3 8.6

Viscosity Index

107

Pour Point, °C

-27

TAN-C

0.5

7.62

7.63

MARINE AND RAIL LUBRICANTS

Page Engine Oils Alexia 50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Argina S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Argina T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Caprinus XR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Caprinus HPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gadinia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Melina . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sirius FB Oil 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.2 8.3 8.3 8.4 8.4 8.6 8.7 8.8

Greases and Rail Lubricants Ossagol C Moly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cardura . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alvania EP D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.27 6.15 6.10

Turbine Shell Turbo T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.58

Marine Separators Omala RL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.41

8.1

MARINE & RAIL

Table of Contents

MARINE AND RAIL LUBRICANTS Alexia Oil 50 - Diesel Engine Cylinder Oil Premium cylinder oil for low speed crosshead diesel engines. Recommended Applications: • For use in the separate cylinder lubrication system of lowspeed, crosshead type, marine diesel engines burning heavy fuel oil with high sulphur content (up to 3.5% wt.) • Slow speed marine diesel engine crankcases Advantages: • Unique additive technology and HVI base stocks • Suited for new highly rated, fuel efficient, slow-speed marine diesel engines operating at higher pressures and temperatures • Designed for use with high sulphur (1.0 to 3.5%) fuels • Minimum deposit formation • Lower cylinder and piston wear • Excellent engine cleanliness • Compatible with sight-glass fluids and normal oil seal materials • Excellent storage stability in conditions on-board ship

Properties

ALEXIA

SAE Grade

50

Product Code

407-415


188 19.0


95 -9


262

TBN-E

70

Sulphated Ash, %wt

8.2

8.11

MARINE AND RAIL LUBRICANTS Argina - Marine Diesel Engine Oils Premium cylinder and crankcase oils for medium speed marine diesel engines: Argina S (TBN = 20) and Argina T (TBN = 30). Recommended Applications: • Cylinders and crankcase oil for medium speed industrial and marine diesel engines burning residual fuel oils with sulphur content up to 2.5% • Marine engine reduction gears Advantages: • Unique additive technology and HVI base stocks • Suited for modern medium speed diesel engines • Excellent detergency to protect against deposits caused by heavy fuels and carbonaceous deposits thus reducing ring and liner wear, blow-by and oil consumption. Excellent engine cleanliness • Excellent TBN retention • Superior thermal stability and resistance to oxidation • Rapidly neutralizes acids for long-term corrosion protection • Formulated without ashless dispersant additives for use with lubeoil separators • Resists sludge formation in the crankcase and under valve covers Approvals: • Approved by many marine engine manufacturers • API CD • Cat Series 3

Properties Grades

ARGINA S 40

T 30

T 40

Product Code

407-437

407-434

407-435


135 14.1

106 12.0

143 14.6

Viscosity Index

102

101

99

Pour Point, °C

-24

-24

-24


274

237

240

TBN-E

20

30

30

Sulphated Ash, %wt

2.5

3.8

3.8

FZG Load Stage Pass

11

11

11 8.3

MARINE AND RAIL LUBRICANTS Caprinus - Railroad and Marine Engine Oils 1.35.04 Premium locomotive crankcase diesel engine oils. Recommended Applications: • Railway, marine and stationary power plant engines • EMD,Alco and GE engines Advantages: • Two TBN levels: • Caprinus XR 13 TBN • Caprinus HPE 17 TBN • Superior TBN retention with unique Shell detergent technology • Excellent viscosity control / retention • Multigrade products offer potential fuel savings • Multigrade products offer potential reduced oil consumption • Unique Shell viscosity index improver used in multigrade products • Totally zinc-free formulations for use in all EMD engines • Compatible with other common railroad diesel engine oils • Caprinus XR 40 is chlorine free • Caprinus XR grades are also chlorine free Approvals: • Accepted by major railroads throughout the world • XR and HPE meet GE’s LMOA Generation 5 extended drain requirement for high horsepower GE engines • HPE meets Caterpillar Micro Oxidation Test • EMD oxidation / corrosion • GE oxidation • Union Pacific oxidation test • CAT 1G-2 bench engine test • API CD

8.4

435-049

146 14.6

101

-25

264

17

1.82


Viscosity Index

Pour Point, °C

Flash Point, °C

TBN-E

Sulphated Ash, % wt

HPE 40

Product Code

Grades

Properties

1.81

17

254

-36

120

126 14.6

435-050

HPE 20W-40

XR 40

1.45

13

273

-27

100

144 14.6

435-055

CAPRINUS

1.46

13

247

-30

119

123 14.5

435-056

XR 20W-40

MARINE AND RAIL LUBRICANTS

Caprinus - Locomotive Engine Oils 1.35.04

8.5

MARINE AND RAIL LUBRICANTS Gadinia - Marine Diesel Engine Oils Premium medium-speed trunk piston engine oils for engines operating on distillate fuels. Recommended Applications: • Highly-rated, medium speed, trunk-piston marine engines operating on distillate fuels • Auxiliary marine engines • Geared transmissions • Turbochargers • Variable pitch propellers • Oil lubricated stern tubes • Deck machinery • Other applications requiring a 30 or 40 wt oil Advantages: • Designed to effectively neutralize corrosive acids which can form from the use of higher sulphur content marine fuels • Protect against rust and corrosion caused by sea water contamination • Ensures a clean engine, free from sludge and deposits • Compatible with all normal oil seal materials • Designed to be used in centrifugal purification systems Approvals: • Approved by most leading trunk piston diesel engine manufacturers • MIL-L-2104C / API CD • MTU Properties Grades

GADINIA 30

40

Product Code

407-418

407-419


107.4 11.8

146.8 14.6

98

98


-24

-21

Flash Point (COC), °C TBN-E

236 12.0

241 12.0

Sulphated Ash, %wt

1.35

1.35

FZG Load Stage Pass

12

12

Zn, ppm

420

420

Ca, ppm

3,800

3,800

360

360

P, ppm 8.6

MARINE AND RAIL LUBRICANTS Melina - Marine Diesel Engine Oils Premium multi-purpose crankcase oil for low speed, trunk-piston and crosshead marine diesel engines. Recommended Applications: • Crankcase systems of low speed, crosshead, marine diesel engines • Main and auxiliary trunk-piston diesel engines burning distillate fuels • Geared transmissions • Turbochargers • Variable pitch propellers • Oil lubricated stern tubes • Deck machinery • Other applications requiring a 30 wt oil Advantages: • Oxidation stability reduces oil thickening and deposits in piston cooling spaces • Excellent dispersancy to prevent sludging and allows for contaminant removal by filters or centrifugal separation • Neutralizes strong and corrosive acids from cylinder oils entering the crankcase • Good water shedding properties • Resistant to corrosion by salt water Approvals: • MIL-L-2104C / API CD • Sulzer - crosshead marine diesel engines • MAN B&W - crosshead marine diesel engines Properties Grades

MELINA 30

Product Code

407-409


108.8 12.0

Viscosity Index

95

Pour Point, °C

-24

Flash Point, °C

274

TBN-E

8.0

Sulphated Ash, %wt

1.0

FZG Load Stage Pass

12 8.7

MARINE AND RAIL LUBRICANTS Sirius FB Oil 30 Marine Diesel Engine Oil Premium quality marine diesel engine oil formulated for use in medium speed trunk piston engines operating on distillate fuels. Recommended Applications: Sirius FB Oil 30 is specifically formulated to control oil consumption in modern distillate fuelled engines where liner lacquering can be a problem. Advantages: • Reduced levels of liner lacquer • High level of protection against bore polishing • Excellent piston and crankcase cleanliness • Ability to release water and contaminants in centrifugal separators • Excellent load carrying properties as required for lubricating reduction gears • Meets API Services Classification CD • Fully approved in Stork,Wartsila Diesel, MWM Deutz, MAN B&W,Alpha Diesel, and MaK engines

Properties Product Code Density at 15°C, kg/m3

SIRIUS FB OIL 30 407-460 887

Pour Point, °C

-24

Viscosity @ 100°C

11.8

Calcium, % mass

0.38

Sulphated Ash, % mass

4.8

TBN-E

13.5

8.8

PROCESS OILS Table of Contents Page 9.4

Naphthenic Shellflex 3131, 3211, 3271, 3311, 3371, 3681, 4131, 4132, 6371 . . . . . . . . . . . . . . . . . . . . . . . . .

9.2

9.1

PROCESS OILS

Paraffinic Shellflex 210, 310, 330, 680, 810 . . . . . . . . . . . . . . . . . .

PROCESS OILS Shellflex - Naphthenic Process Oils Refined, naphthenic petroleum fractions. Recommended Applications: • Rubber compounding / manufacturing • Elastomers • Adhesives • Carrier oils • Plasticizers • Most process oil applications Advantages: • Rich in naphthenic cyclic chemical structures • Very consistent physical and chemical properties • Wide range of viscosities available • Do not contain any additives • Low natural pour points • Good stability • Improved solvency over paraffinic process oils

9.2

3.02.02

224

99

--

Flash Point, °C

Aniline Point, °C

VG Constan

--

--

Refractive Intercept

Rel. Molecular Mass

1.4898

31

-29

Pour Point, °C

8.28

Viscosity, cSt @ 100°C

Viscosity Index

897

92.9


Refractive Index @ 20°C

3131

3211

3271

3311

3371

SHELLFLEX (NAPHTHENIC) OILS

886

390

1.046

1.4867

0.8434

84

174

-21

52

3.8

20.2

897

365

1.044

1.4938

0.8467

89

200

-12

60

5.5

40.2

901

420

1.0456

1.4950

0.8450

91

210

-15

63

6.7

54.3

904

440

--

1.4981

0.8371

92

213

-18

73

8.4

79.5

4131

6371

465

--

1.5024

0.8348

96

229

-15

60

12.2

149.9

910

92.0 45

261

--

1.4815

0.865

76

155

-51

--

--

1.4896

--

97

213

-28

36

8.19

9.3 2.6

903.9

885

410-681 410-431 410-637

3681

Shellflex - Naphthenic Process Oils

325

1.0425

1.4793

0.8415

80

157

-36

59

2.4

9.18

872

410-371 410-313 410-321 410-327 410-331 410-337

371

Density @ 15°C, kg/m3

Product Code

Grades

Properties

PROCESS OILS 3.02.02

9.3

PROCESS OILS Shellflex - Paraffinic Process Oils

3.02.02

Refined, paraffinic (HVI) petroleum fractions. Recommended Applications: • Dust suppressant • Rubber compounding / extending component • Shellflex 210, 310, 330 and 680 are ASTM 1048 type rubber extending oils • Shellflex 810 is an ASTM 103 type rubber extending oil • Carrier oil • Elastomer manufacture • Plasticizers • Adhesives • Most process oil applications Advantages: • • • • • • •

High concentration of saturated chemical structures Very consistent physical and chemical properties Wide range of viscosities available Do not contain any additives Low natural pour points for paraffinic oils Good stability Modest solvency

9.4

98

Aniline Point, °C

1.4709

1.0430

0 34 66

365

Refractive Index @ 20°C

Refractive Intercept

Carbon Type, %m Aromatic Naphthenic Paraffinic

Rel. Molecular Mass

0.8142

220

Flash Point, °C

VG Constant

95

-18

4.0


Pour Point, °C

20.3


Viscosity Index

862.5

410-210

Density @ 15°C, kg/m3

Product Code

435

515

0 31 69

1.0432

1.4790

0.8042

117

274

-9

95

12.3

117

879.0

410-680

700

2.6 28.3 69.1

1.0442

1.4880

0.8000

126

334

-9

95

33

526

894.7

410-810

810

Shellflex - Paraffinic Process Oils

0 34 66

1.0420

1.4760

0.8113

107

242

-12

95

7.2

51.2

874.1

410-310

680

310

Grades

210

SHELLFLEX (PARAFFINIC) OILS

Properties

PROCESS OILS 3.02.02

9.5

SPECIALTY LUBRICANTS Table of Contents Page Biodegradable Nautilus Biodegradable Outboard Motor Oil. . . . . . . . . 10.9 Nautilus Biodegradable Bilge Cleaner . . . . . . . . . . . . . . 10.13 Nautilus Biodegradable Boat Cleaner . . . . . . . . . . . . . . 10.14

10.6

Chain Oil Chain Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.7

Engine Oils 4 Stroke Nautilus 4 Stroke Engine Oil. . . . . . . . . . . . . . . . . . . 10.10 2 Stroke Shell Advance Premium Snowmobile Oil . . . . . . . . . 10.3 Advance Snow Ultra - Syn. Snowmobile Oil . . . . . . . 10.4 Nautilus Premium Outboard Motor Oil. . . . . . . . . . . 10.8 Nautilus PWC Personal Watercraft Oil. . . . . . . . . . . . 10.17 XTC-50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.18 Gear Nautilus Marine Gear Oil . . . . . . . . . . . . . . . . . . . . . . . 10.12 Nautilus Synthetic Gear Oil . . . . . . . . . . . . . . . . . . . . . 10.16 Grease Advance Snow Ultra. . . . . . . . . . . . . . . . . . . . . . . . . . .

6.4

Pump Nautilus Jet Pump Oil . . . . . . . . . . . . . . . . . . . . . . . . . 10.15

10.1

SPECIALTY LUBES

Chain Case Oils Advance 100% Synthetic Chain Case Oil . . . . . . . . . . .

SPECIALTY LUBRICANTS

10.2

SPECIALTY LUBRICANTS Shell Advance Premium Snowmobile Oil

1.06.13

A premium mineral based, 2 stroke snowmobile oil. Recommended Applications: • High output 2 stroke snowmobile engines • Pre-mix applications and oil injection systems Advantages: • Ashless formulation minimizes plug fouling and preignition • Reduced exhaust smoke, up to 85% • Low exhaust odour, no ammonia odour • Superior low temperature performance, SAE Category 4 @-40°C • Improved lubricity and scuffing performance • Detergent / dispersant formulation minimizes deposit formation • Protects engine against rust Approvals: • Meets all major snowmobile manufacturers recommendations including Arctic Cat, Bombardier, Polaris,Yamaha • Exceeds TC-W3* • Meets API TC • Meets JASO FC smoke emission standard Properties Product Code

SHELL ADVANCE PREMIUM SNOWMOBILE OIL 427-511

API Rating

TC

SAE Fluidity/Miscibility Rating

4

Colour

Blue


27.3 5.8


11,600

Pour Point, °C

-51

Flash Point, °C

79

10.3

SPECIALTY LUBRICANTS Advance Snow Ultra Premium Synthetic Snowmobile Oil

1.14.06

A high performance, synthetic, 2 stroke snowmobile engine oil. Recommended Applications: • High performance, high output 2 stroke snowmobile engines • Including those with variable exhaust systems such as RAVE* • Pre-mix and direct oil injection systems Advantages: • Low ash, synthetic formulation minimizes plug fouling and preignition • Detergent / dispersant formulation minimizes piston and ring deposits • Superior low temperature performance • Reduced exhaust smoke, visible exhaust smoke is essentially eliminated after warm-up • No ammonia odour formulation • Improved lubricity and anti-scuffing protection • Superior rust protection • Proven performance • Designed for unleaded gasoline up to 100:1 mixing ratio Approvals: • Meets all major snowmobile manufacturers recommendations including Arctic Cat, Bombardier, Polaris,Yamaha • Exceeds highest API-TC, JASO-FC and ISO-EGD standards for detergency, lubricity, pre-ignition, exhaust system blockage and reduced visible exhaust smoke emission

10.4

SPECIALTY LUBRICANTS Advance Snow Ultra Premium Synthetic Snowmobile Oil Properties Product Code

1.14.06

ADVANCE SNOW ULTRA 427-512

API Rating

TC


4

Colour Viscosity, cSt 40°C 100°C Brookfield Viscosity, cP -40°C

Golden Amber 57.1 9.46 37,400

Pour Point, °C

-57

Flash Point, min. °C

80

TBN-E

1.3

Ash Content, % m

0.10

10.5

SPECIALTY LUBRICANTS Advance 100% Synthetic Chain Case Oil

1.18.02

A premium 100% synthetic chain case oil for enclosed chain case systems Recommended Applications: All season service in enclosed chain drives for snowmobiles, ATVs and other recreational vehicles. Advantages: • Outstanding low temperature flow • All-Season operation enabling it to provide maximum protection over a wide range of temperatures. • Additive system to provide outstanding protection and lubrication of chains and sprockets. Properties Product Code

ADVANCE 100% SYNTHETIC CHAIN CASE OIL 427-582

Density at 15°C - Kg/m3

902

Pour Point °C

-40

Viscosity Kinematic cSt @ 40 °C cSt @ 100 °C

122 16.6

Brookfield cP @ -40 °C

125,000

Viscosity Index

150

Copper Strip Corrosion Test @ 100 °C for 3 hrs. Foam Sequence I Sequence II Sequence III

Pass Pass Pass Pass

10.6

SPECIALTY LUBRICANTS Chain Oils - Chain Lubricant

1.25.07

Premium mineral oils for all chains including chains and bars of power chain saws. Recommended Applications: • All chains, including oil baths, hand and automatic lubricated • Bars and chains of high performance professional power chain saws • Conveyor systems, sawmills, woodlands, mining operations • NOT to be used as an engine oil in the power heads of saws. For 2 stroke engine oil see Shell XTC-50 Oil Advantages: • Additive system protects the chain, bar and sprockets from wear • Tacky nature reduces fling-off from the chain • Red colour helps distinguish this chain oil from engine oils • Rust Inhibited Properties Grades Product Code

CHAIN OILS Light

Heavy

431-222

431-221

Colour

Red

Red


70 9

91 12

Pour Point, °C

-33

-15

Flash Point, °C

220

200

10.7

SPECIALTY LUBRICANTS Nautilus - Premium Outboard Motor Oil

1.09.09

A premium mineral oil based,TC-W3*, 2 stroke outboard motor oil. Recommended Applications: • All water cooled 2 stroke outboard engines for both pre-mix and direct oil injection systems • For a full synthetic oil for personal watercraft, use Shell Nautilus PWC Advantages: • Dispersant formulation • Improved lubricity and anti-scuffing protection • Low aquatic toxicity • Reduces plug fouling and preignition • Minimizes piston deposits • Superior rust protection • Reduced smoke • Compatible with other TC-WII* and TC-W3* lubricants • Dyed blue for easy identification in pre-mix systems Approvals: • Exceeds the NMMA TC-W3* standards • Recommended for OMC, Mercury Marine,Yamaha, Susuki, Nissan • Meets JASO FC reduced smoke emission standard

Properties

NAUTILUS

Product Code

427-531

API Rating NMMA Rating SAE Fluidity/Miscibility Rating

TC TC-W3 4

Colour

Blue


27.3 5.8


11,600

Pour Point, °C

-51

Flash Point, °C (PMCC)

79

TBN-E Ash Content

10.8

9.1 0.003

SPECIALTY LUBRICANTS Nautilus Biodegradable Outboard Motor Oil 1.40.02 A premium, biodegradable TC-W3*, 2 stroke outboard motor oil. Recommended Applications: • All water cooled 2 stroke outboard engines for both pre-mix and direct oil injection systems Advantages: • Synthetic based formulation • Ashless, dispersant formulation • Improved lubricity and anti-scuffing protection • Less aquatic toxicity • Reduces plug fouling and preignition • Minimizes piston deposits • Superior rust protection • Designed for unleaded gasoline • Blends easily and stays mixed • Compatible with other TC-WII* and TC-W3* lubricants Approvals: • Exceeds the recertification requirements of NMMA TC-W3* • Fully approved by Canada’s Environmental Choice Program • Meets biodegradability requirements of CEC L-33 T-82 • Recommended for OMC, Mercury Marine,Yamaha, Susuki, Nissan

Properties

NAUTILUS BIODEGRADABLE OUTBOARD MOTOR OIL

Product Code

427-536

NMMA Rating

TC-W3

Colour Viscosity, cSt 100°C Brookfield Viscosity, cP -25°C

Blue/Green 9.1 5,835

Pour Point, °C

-40

Flash Point, °C

110

TBN-E

2.9

10.9

SPECIALTY LUBRICANTS Nautilus 4 Stroke Engine Oils

1.41.04

4 stroke inboard and outboard motor oils. Applications: • Water cooled, gasoline and diesel, inboard and outboard 4 stroke engines • Recommended for all makes and models of 4 stroke engines including Mercury, Honda, OMC and Yamaha • Consult your owners manual for the proper grade and API service classification Advantages: • Viscosity retention to stay-in-grade.The 25W-40 is formulated without Viscosity Index Improver additives to provide maximum viscosity retention • Corrosion protection for this severe environment • Longer engine life from improved engine and piston deposit control • Wear protection • Antifoam control • Low oil consumption Recommendations: • SAE 10W-30 is API CH-4, CG-4, CF-4, CF/SH • SAE 25W-40 is API SJ, CD • SAE 30 is API SJ

10.10

SPECIALTY LUBRICANTS Nautilus 4 Stroke Engine Oils Properties

1.41.04

NAUTILUS 4 STROKE ENGINE OILS

Grades

10W-30

25W-40

30

Product Code

425-533

425-534

427-571


76.7 11.8

134.0 14.5

97.7 11.5

Viscosity Index

149

107

106

CCS (cranking), cP -5°C -20°C

-2,850

3,000 --

---

MRV Apparent Visc, cP -15°C -30°C

-23,169

9,860 --

---

Pour Point, °C

-33

-24

-30

Sulphated Residue, % wt

1.25

0.75

0.75

TBN-E

10.3

7.5

6.0

Flash Point, °C

219

229

229

10.11

SPECIALTY LUBRICANTS Nautilus Marine Gear Oil

1.42.02

A mineral based, premier, multi-purpose, all season multigrade, EP gear oil. Recommended Applications: • Inboard and outboard gear cases where Type C, 80W-90 gear oils are recommended Advantages: • Excellent extreme pressure load carrying ability • Ultimate rust protection needed in a marine environment • Thermal and oxidation stability to eliminate deposits that form around seals • Controls foaming in gear cases • Retains viscosity and a protective oil film from the use of a shear stable viscosity index improver additive Approvals: • GL-5 • Exceeds Original Equipment Manufacturers (OEM) requirements • Recommended for all major inboard and outboard gear cases including Mercury, Honda, OMC and Yamaha

Properties Grade

NAUTILUS MARINE GEAR OIL 90

Product Code

437-535


134 14.7

Viscosity Index

110

Pour Point, °C

-24

Flash Point, °C

218

10.12

SPECIALTY LUBRICANTS Nautilus Biodegradable Bilge Cleaner

1.43.01

A biodegradable cleaner for recreational boat bilges. Recommended Applications: • Cleaning bilges of boats. Will remove oil, wax and other protective coatings • This product is not to be used as a lubricant Advantages: • Biodegradable - cleaner degrades before having a negative impact of aquatic life • Not harmful to marine, plant and water organisms • Non flammable • Non explosive • Contains no nitrates, phosphates, sulphates or chlorine. • Cleaner mixed with water disperses oil from the bilge. See our “Lubricants Report” for mixing details • No special handling procedures or protective clothing required Approvals: • Meets biodegradability requirements of the Environmental Choice Program (ECP)


NAUTILUS BIODEGRADABLE BILGE CLEANER 427-551

Specific Gravity

1.006

Cleaner pH

10.2

10.13

SPECIALTY LUBRICANTS Nautilus Biodegradable Boat Cleaner

1.44.01

A biodegradable cleaner for recreational boats. Recommended Applications: • Cleaning boat bottoms and hulls - water lines and salt water spots • Engine rooms and oily surfaces • Rust and corrosion from refrigeration containers • Mildew, mould and oil from bilges • Swabbing decks and bulkheads • Atomized in air for odour control • This product is not to be used as a lubricant Advantages: • Biodegradable - cleaner degrades before having a negative impact of aquatic life • Not harmful to marine, plant and water organisms • Non flammable • Non explosive • Contains no nitrates, phosphates, sulphates, detergents and chlorines. • Cleaner mixed with either fresh or salt water. See our “Lubricants Report” for mixing details • No special handling procedures or protective clothing required Approvals: • Meets biodegradability requirements of the Environmental Choice Program (ECP)


NAUTILUS BIODEGRADABLE BOAT CLEANER 427-561

Specific Gravity

1.006

Cleaner pH

10.2

10.14

SPECIALTY LUBRICANTS Nautilus Jet Pump Oil

1.46.01

Nautilus Jet Pump Oil is a premium, fully synthetic personal watercraft jet pump lubricant. Recommended Applications: • Jet pump lubricant for personal watercraft which require oil top-up or replacement • Severe service including high temperature conditions Advantages: • Full synthetic • Extreme pressure additives for excellent wear protection • Extended drain intervals Approvals: • Meets GL-5 requirements

Properties

NAUTILUS JET PUMP OIL

Product Code

427-591


122 16.6

Viscosity Index

147

Brookfield Viscosity , cP @ -40°C Pour Point, °C

120,000 <-45

10.15

SPECIALTY LUBRICANTS Nautilus Synthetic Gear Oil

1.45.01

Nautilus Synthetic Gear Oil is a premium, fully synthetic, extreme pressure marine gear oil. Recommended Applications: • High performance outboard engine lower gear units, including those operating at high temperatures Advantages: • Extended drain capability, three times that of conventional gear oils • Extreme Pressure additives for maximum wear protection Approvals: • MIL-PRF-2105E • API MT-1

Properties

NAUTILUS SYNTHETIC GEAR OIL

Product Code

427-581


115 16.0

Viscosity Index

162

Pour Point, °C

-51

10.16

SPECIALTY LUBRICANTS Nautilus PWC Personal Watercraft Oil

1.47.01

A high performance, synthetic, 2 stroke personal watercraft engine oil. Recommended Applications: • High performance, high output 2 stroke personal watercraft engines • Including those with variable exhaust systems such as RAVE* • Water cooled and air cooled • Pre-mix and direct oil injection systems Advantages: • Low ash, synthetic formulation minimizes plug fouling and preignition • Detergent / dispersant formulation minimizes piston and ring deposits • Improved lubricity and anti-scuffing protection • Superior rust protection • Designed for unleaded gasoline up to 100:1 mixing ratio • Proven performance • No ammonia odour • Reduced exhaust smoke, visible exhaust smoke is essentially eliminated after warm-up Approvals: • Exceeds all major Personal Watercraft engine manufacturers recommendations. Recommended and guaranteed for use in Sea-doo, Polaris and Yamaha • Exceeds highest API-TC, JASO-FC and ISO-EGD standards for detergency, lubricity, pre-ignition, exhaust system blockage and reduced visible exhaust smoke emission Properties Product Code API Rating Colour Viscosity, cSt 40°C 100°C Brookfield Viscosity, cP -40°C Pour Point, °C

NAUTILUS PWC 427-541 TC Golden Amber 57.1 9.46 37,400 -57

Flash Point, °C (PMCC) min.

80

TBN-E

1.3

Ash Content, % m

0.10 10.17

SPECIALTY LUBRICANTS XTC 50 - 2 Stroke Engine Oil

1.23.03

A premium, mineral based lubricant for 2 stroke air-cooled engines. Recommended Applications: • Chain saws, lawn equipment, snowblowers • Suitable for pre-mix and direct oil injection • Small engines up to 50:1 fuel to oil ratios • For liquid cooled 2 stroke engines Shell Nautilus Premium Outboard Motor Oil or Shell Advance Premium Snowmobile Oil are preferred • For high performance applications Shell Advance Snow Ultra and Nautilus Personal Watercraft High Performance Synthetic Oil are preferred Advantages: • Low ash formulation • Excellent piston cleanliness • Reduced spark plug fouling and combustion chamber deposits • High temperature protection • Blue colour for easy of identification in pre-mix fuels Approvals: • Exceeds API TC classification in piston scuffing, preignition deposits and ring sticking


XTC 50 427-520

API Rating

TC


4

Colour

Blue


24.3 4.5


15,000

Pour Point, °C

-45

Flash Point PMCC, °C COC, °C

83 110

TBN-E

1.18

Ash Content

0.06

10.18

SYNTHETIC LUBRICANTS Table of Contents Page Chain Case Oils Advance 100% Synthetic Chain Case Oil . . . . . . . . . . .

10.6

Compressor Oils Clavus AB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clavus HFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Corena AS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Corena DE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Corena NG (Partial Syn) . . . . . . . . . . . . . . . . . . . . . . .

7.7 7.8 7.10 7.12 7.14

Gear Oils Dentax S 50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hyperia S 220 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Omala HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Omala RL (non EP) . . . . . . . . . . . . . . . . . . . . . . . . . . . Spirax HD 75W-90 (Partial Syn) . . . . . . . . . . . . . . . . . Spirax S 75W-90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tivela . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.29 7.28 7.40 7.41 3.26 3.28 7.53

Greases Advance Snow Ultra . . . . . . . . . . . . . . . . . . . . . . . . . . Darina XL 102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Retinax TL 00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SRS 2000 (Partial Syn) . . . . . . . . . . . . . . . . . . . . . . . . . Ultragel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.4 6.20 6.28 6.30 6.33

Hydraulic Oils Tellus HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.48

11.1

SYNTHETIC LUBES

Engine Oils Advance Snow Ultra . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4 FormulaShell (Partial Syn) . . . . . . . . . . . . . . . . . . . . . . 3.12 FormulaShell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.14 Nautilus PWC Personal Watercraft Oil . . . . . . . . . . . . . 10.17 Rotella T SB (Partial Syn) . . . . . . . . . . . . . . . . . . . . . . . 3.22

APPENDIX Appendix Index Page ASTM TEST METHODS . . . . . . . . . . . . . . . . . . . . . . . . . 12.3 Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.4 SAE Crankcase Oil Viscosity Grades. . . . . . . . . . . . . . 12.8 API Services - Engine Oils . . . . . . . . . . . . . . . . . . . . . . 12.12 AGMA Gear Lubricant (Viscosity) Classifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAE Gear Oil Viscosity Grades . . . . . . . . . . . . . . . . . . API Services - Automotive Gear Oils. . . . . . . . . . . . . . Engine And Transmission Lubricants, Recommendations by Specifications and Grade . . Grease Thickeners . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grease Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . NLGI Grease Grading System . . . . . . . . . . . . . . . . . . . NLGI Grease Service Classifications . . . . . . . . . . . . . .

12.9 12.10 12.11 12.13 12.16 12.17 12.18 12.18

API Gravities and Densities Table. . . . . . . . . . . . . . . . 12.22 Conversion Factors (various units) . . . . . . . . . . . . . . 12.23 Table of Temperature Conversions . . . . . . . . . . . . . . 12.24

12.1

APPENDIX

Comparable Viscosity Grades . . . . . . . . . . . . . . . . . . . 12.19 Viscosity Conversions (SUS - cSt) . . . . . . . . . . . . . . . . 12.20 ISO Viscosity Grades . . . . . . . . . . . . . . . . . . . . . . . . . . 12.21

APPENDIX

12.2

APPENDIX ASTM Test Methods Test Method Number Acidity as Acetic Acid . . . . . . . . . . . . . . . . . . . . D 1613 Ash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D 4530 Ash (aviation oils) . . . . . . . . . . . . . . . . . . . . . . . D 482 Autoignition Temperature . . . . . . . . . . . . . . . . . D 2155 Biodegradability . . . . . . . . . . . . . . . . . . . . . . . . CEC-L-33-T-82 Brookfield Viscosity . . . . . . . . . . . . . . . . . . . . . . D 2983 CCR Residue . . . . . . . . . . . . . . . . . . . . . . . . . . . D 189 CCS (Cold Cranking Simulator,Viscometer) . . . . D 2602 Chloride (Coolant) . . . . . . . . . . . . . . . . . . . . . . D 3634 Colour, Pt-Co Scale . . . . . . . . . . . . . . . . . . . . . . D 1209 Density . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D 1298 Density (Coolant @ 15.6∞C) . . . . . . . . . . . . . . . D 1122 Density (Coolant @ 25∞C) . . . . . . . . . . . . . . . . D 941 Dielectric Strength (DISC electrodes) . . . . . . . . D 877 Dielectric Strength (VDE electrodes) . . . . . . . . . D 1816 Flash Point (Cleveland Open Cup,COC) . . . . . . D 92 Flash Point (Pensky Marten Closed Cup, PMCC) . . D 93 Flash Point (TAG Closed Cup) . . . . . . . . . . . . . . D 56 Fire Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D 92 Floc Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-86-83,ASHRAE Freeze Point . . . . . . . . . . . . . . . . . . . . . . . . . . . D 2386 Freezing Point (Coolant) . . . . . . . . . . . . . . . . . . D 1177 FZG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DIN 51-354 Interfacial Tension . . . . . . . . . . . . . . . . . . . . . . . D 971 MRV (Mini Rotary Viscometer) . . . . . . . . . . . . . D4684 PH (Coolant) . . . . . . . . . . . . . . . . . . . . . . . . . . . D 1287 Pour Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D 97 Power Factor (electrical) . . . . . . . . . . . . . . . . . . D 924 Reserve Alkalinity (Coolant) . . . . . . . . . . . . . . . D 1121 Saponification Number . . . . . . . . . . . . . . . . . . . D 94 Sulphated Ash . . . . . . . . . . . . . . . . . . . . . . . . . . D 874 TAN-C (Total Acid Number) . . . . . . . . . . . . . . . . D 974 TAN-E (Total Acid Number) . . . . . . . . . . . . . . . . D 664 TBN-E (Total Base Number) . . . . . . . . . . . . . . . . D 2896 Timken OK Load. . . . . . . . . . . . . . . . . . . . . . . . D 2782 Turbine Oil Stability Test . . . . . . . . . . . . . . . . . . D 943 Viscosity (Kinematic) . . . . . . . . . . . . . . . . . . . . D 445 Viscosity Index . . . . . . . . . . . . . . . . . . . . . . . . . D 2270 Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D 1744 Tests Specific to Greases Base Oil Viscosity . . . . . . . . . . . . . . . . . . . . . . . Coefficient of Friction . . . . . . . . . . . . . . . . . . . . Dropping Point . . . . . . . . . . . . . . . . . . . . . . . . . Penetration . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timken OK Load. . . . . . . . . . . . . . . . . . . . . . . . Water Washout . . . . . . . . . . . . . . . . . . . . . . . . . 4-Ball EP - Load Wear Index . . . . . . . . . . . . . . . . 4-Ball EP - Weld Load . . . . . . . . . . . . . . . . . . . . . 4-Ball Wear Scar . . . . . . . . . . . . . . . . . . . . . . . . . Water Washout . . . . . . . . . . . . . . . . . . . . . . . . .

D 445 D 5183 D 2265 D 217 D 2509 D 1264 D 2596 D 2596 D 2266 D1264 12.3

APPENDIX Glossary of Terms The descriptions given here are intended to be of a general nature and may not be an absolute full and scientific explanation of the term. ACID NUMBER or TOTAL ACID NUMBER - a measure of the acidic nature of an oil. The specific quantity of base required to neutralize the acidic component in an oil. The value typically increases during usage, as acids accumulate in the oil. Measured in mg. of KOH (base) to neutralize one gram of oil. AGMA - American Gear Manufacturers Association ANTI-WEAR ADDITIVE - an additive used in lubricating oils which react with the metal surface to reduce the amount of wear occurring between contacting surfaces. Zinc (dialkyl dithiophosphate) is a common example. API - American Petroleum Institute ASH or SULPHATED ASH - an indication of the noncombustible residue of an oil. The deposit left after all of the base oil has been burned away. Metallic detergents and antiwear additives contribute to the ash content of an oil. ASTM - American Society for Testing and Materials, establish the ASTM Test Methods used by laboratories. AUTOIGNITION TEMPERATURE - the temperature at which a sample of oil can be heated before it will spontaneously ignite without a source of ignition. It will be a higher value than the flash or fire points. BASE NUMBER or TOTAL BASE NUMBER - a measure of the basic or alkaline nature of an oil. The specific quantity of acid required to neutralize the basic component in an oil. The value decreases as some of the additives are consumed during use. Measured in mg. of KOH to neutralize one gram of oil. BASE OIL or BASE STOCK - the oil portion of a lubricating oil or grease. May be mineral or synthetic.

12.4

APPENDIX Glossary of Terms BEARINGS: Rolling Element Bearing or Anti-friction Bearing - any bearing using rollers or balls e.g. ball bearing, spherical, cylindrical, needle. May accept radial and/or thrust loads. Journal Bearing or Plain Bearing - any bearing that does not employ rolling elements, typically consisting of a shaft rotating in a cylindrical shell. Also referred to as Shell or Sleeve Bearing. May accept radial or thrust loads. BROOKFIELD VISCOSITY - a low temperature, low shear viscosity commonly used to measure the performance of gear oils and hydraulic oils. CCR RESIDUE - Conradson Carbon Residue, the percent of coked material left after a sample of oil is exposed to high temperatures by a prescribed method. CCS - Cold Cranking Simulator, a low temperature, high shear viscosity commonly used to measure the ability of a motor oil to allow the crankshaft of an engine to spin during start-up. CENTISTOKE (cSt) - one one-hundredth of a stoke. A common unit of kinematic viscosity. Equal in value to a mm2/s. CENTIPOISE (cP) - one one-hundredth of a poise. A common unit of absolute viscosity. Brookfield, Cold Cranking Simulator and Mini Rotary Viscometer all measure absolute viscosity and the resulting values are given in centipoise. May be converted to centistoke by dividing by the density of the oil (at the same temperature). Equal in value to a milli Pascal second (mPa.s). CGSB - Canadian General Standards Board, develops standards for products and test methods specific to Canada. CHANNEL POINT - the lowest temperature at which a paddle can be pulled through a sample of cold oil and the walls created by the paddle due not flow back into the channel (within a prescribed time) COMPOUNDED OIL - an oil containing either natural or synthetic fatty materials as additives DEMULSIBILITY - the ability of an oil to separate (release or drop) water from the oil.

12.5

APPENDIX Glossary of Terms DROPPING POINT - the highest temperature to which a grease can be heated before a drop of oil separates (and drops) from the grease (under prescribed conditions). EP - Extreme Pressure additive. An additive used in lubricating oils or greases which react with the metal surface to reduce the amount of adhesion or cold-welding which may occur between contacting surfaces under severe loads or shock loading. Sulphur-phosphorous chemicals are a common example used in gear oils. FOUR (4) BALL TESTER - one of two laboratory machines. The 4 Ball Wear Tester which indicates the wear protection offered by a lubricant by measuring a scar diameter on four steel balls. The 4 Ball EP Tester which indicates the extreme pressure load carrying capacity of a lubricant. The test method determines a Weld Load and a calculated Load Wear Index (LWI). FLASH POINT - the lowest temperature at which an oil creates enough vapour above the surface of the oil to yield a combustible mixture which will ignite or explode in the presence of a spark, but insufficient vapour to sustain a flame. COC - Cleveland Open Cup Method, used for lubricating oils. PMCC - Pensky-Martens Closed Cup Method, used for fuel oils or lubricants that contain lighter solvent-like materials. TAGCC - Tag Closed Cup Method, used for solvents. FLOC POINT - used to indicate the lowest temperature that a refrigeration oil can be cooled before wax or other components begin to solidify. ISO - International Standards Organization LUBRICANT - may be either an oil or a grease or a solid used to reduce friction between two surfaces. MINERAL OIL - a base oil (base stock) derived from crude oil at a refinery by separation and purification processes including combinations of fractionation, solvent extraction, hydrofinishing, hydrotreating, hydrocracking, dewaxing. MRV - Mini Rotary Viscometer, a low temperature, low shear viscosity commonly used to measure the ability of an oil to flow toward (flood) the suction of an automotive engine’s oil pump. It is used to predict and prevent oil starvation during engine start-up.

12.6

APPENDIX Glossary of Terms NEUTRALIZATION NUMBER - may be either the acid number or base number of an oil. The amount of acid or base required to neutralize an oil. NLGI - National Lubricating Grease Institute. PENETRATION - the consistency or hardness of a grease. The penetration of a cone into a sample of grease indicates its’ hardness and is used to assign the NLGI grease grade numbers e.g. a #2 grade grease. PROCESS OIL - typically a base oil used in a manufacturing process and not used directly for lubrication e.g. rubber extenders, dedusting. R&O - a rust and oxidation inhibited lubricating oil. It may contain an antifoam additive but will not contain an antiwear or EP additive. SAE - Society of Automotive Engineers. SOLVENT EXTRACTION - a refining process for base oils used to remove the undesirable components. STLE - Society of Tribologists and Lubrication Engineers SULPHATED ASH - See Ash. SYNTHETIC - man-made, synthesized (not naturally occurring) base oil. Various chemical types exist. SYNTHETIC BLEND - an oil containing both mineral oil base stock and synthetic oil base stock. TIMKEN OK LOAD - a measure of the extreme pressure (EP) properties of an oil or grease. The “OK Load” is the heaviest load that the film of lubricant can support without scoring. Test results can vary significantly. TOTAL ACID NUMBER (TAN) - See Acid Number TOTAL BASE NUMBER (TBN) - See Base Number

12.7

12.8

9,500 @ -15

13,000 @ -10

--

--

--

--

--

--

20W

25W

20

30

40

40

50

60

--

--

--

--

--

--

60,000 @ -15

60,000 @ -20

60,000 @ -25

21.9

16.3

12.5

12.5

9.3

5.6

9.3

5.6

5.6

4.1

3.8

3.8

Min. Kinematic (cSt) Max @ °C

< 26.1

< 21.9

< 16.3

< 16.3

< 12.5

< 9.3

--

--

--

--

--

--

Max. Kinematic Viscosity (cSt) @ 100°C

3.7

3.7

3.7 (15W-40, 20W-40, 25W-40, 40)

3.3 (0W-40, 5W-40, 10W-40)

2.9

2.6

--

--

--

--

--

--

High Shear (cP) min. @ 150°C & 106s-1

HIGH TEMPERATURE VISCOSITIES

* All values are critical specifications as defined by ASTM D 3244 SAE J-300 (Dec 99 Revision)

7,000 @ -20

15W

60,000 @ -30

60,000 @ -35

6,600 @ -30

7,000 @ -25

5W

10W

60,000 @ -40

6,200 @ -35

0W

MRV Pumping (cP) Max @ °C

CCS Cranking Viscosity (cP) max. @ °C

Viscosity Grade

LOW TEMP. VISCOSITIES

APPENDIX

SAE Viscosity Classification for Crankcase Oils*

APPENDIX AGMA Gear Lubricant Classifications VISCOSITY RANGES FOR INDUSTRIAL GEAR OILS - AGMA 250.04 AGMA No.

VISCOSITY RANGE CSt. @ 40°C

COMPARABLE ISO GRADE

1

41.4 - 50.6

46

2 & 2 EP*

61.2 - 74.8

68

3 & 3 EP

90.0 - 110

100

4 & 4 EP

135 - 165

150

5 & 5 EP

198 - 242

220

6 & 6 EP

288 - 352

320

7 Comp.** & 7 EP

414 - 506

460

8 Comp. & 8 EP

612 - 748

680

8A Comp. & 8A EP

900 - 1000

1000

*EP designates extreme pressure inhibited gear oil grades. **Comp. designates oil compounded with 3% to 10% fatty or synthetic fatty components.

12.9

12.10 --

24.0 41.0

140

--

41

250

-40

4.1

75W

150

--

13.5 24.5

90

Flash Point, °C Max.

-12

11

85W

-45

-26

7

80W

165

-35

-26

13.5 24.0

80W-90

MIL - L - 2105D Grades

Channel Point, °C Max.

-40

4.1

Viscosity, cSt 100°C Min. Max.

Max. Temp (C) for 150,000 cP Visc.

75W

PROPERTY

SAE Gear Oil Viscosity Grades

180

-20

-12

24.0 41.0

85W-140

APPENDIX

Physical Requirements for Automotive Gear Lubricants

APPENDIX API Services - Automotive Gear Oils API - GL-1 to GL-3 Designates the type of service characteristic of automotive spiral-bevel and worm-gear axles and some manually operated transmissions operating under mild or moderate conditions of pressures and sliding velocities. API - GL-4 Designates the type of service characteristic of gears, particularly hypoid in passenger cars and other automotive type equipment operating under high-speed, low torque, and lowspeed, high torque conditions. API - GL-5 Similar to GL-4 but designed to protect automotive equipment operated under high-speed shock-load. API GL-6 Obsolete MT-1 Recently adopted standard. Designates use in non-synchronized manual transmissions. PG-2 (Proposed Classification) Developed to replace API - GL5. Shell Spirax HD gear lubricants are approved against this standard when it becomes official.

12.11

APPENDIX API Services - Engine Oils “S” - SERVICE (Gasoline) API SERVICES SA to SG: Obsolete These service designations are an alphabetical evolution of protection levels originated back in the early 1960’s. As gasoline engines became more severe, better motor oils were developed. API SERVICE SH: Category for 1994 model (and later) warranty requirements. API SERVICE SJ: Category for 1996 model (and later) warranty requirements. API SERVICE SL: Category for 2001 model (and later) warranty requirements.The current service level that ensures optimum gasoline engine life. “C” - SERVICE (Diesel) API SERVICES CA to CE: Obsolete Similar to “S” service designations is protection level evolution but pertaining mainly to diesel engines. API SERVICE CF-2: 1994 severe duty 2-cycle diesel engines. API SERVICE CF-4: Severe duty turbocharged 4-cycle diesel engines: highest protection against high and low temperature deposits, wear, corrosion, especially late model (since 1988) lower emission engines: Mack EO-K/2, Cummins NTC 400, Caterpillar 1-K. API SERVICE CG-4: Enhanced protection for high speed 4-cycle diesel engines to meet 1994 exhaust emission standards. API SERVICE CH-4 Enhanced protection for high speed 4-cycle diesel engines to meet 1998 exhaust emission standards.

12.12

12.13

R R R

R

R R R

R R R R R

R R R

R R

R R

R R

R

R R R

R R R R R

R

R

R

R R R

RECOMMENDATIONS - DIESEL

R

R R R

R R

R

R

R R R

R R

R

R

R R

R

R

R R

R

R

R R

R R

R

R

R

R=RECOMMENDED FOR THE CORRESPONDING SPECIFICATION CATEGORY.

Rotella T Plus 15W-40 Rotella T with XLA 10W-30 15W-40 Rotella T 10W 20W-20 30 40 50 Rotella T SB Syn. Blends: 10W-40 0W-30 5W-30 100% Syn.: 0W-40

Product

R

R R

R

R

R

R

R

R

R

R

R R R

R R

R

R

R R

R

R

RECOMMENDATIONS - GASOLINE

R R R

R R R R R

R R

R

MACK Cummins Cummins CES CES API API API API API API API API MACK E0-M Volvo Volvo API API API ILSAC Energy Allison 20076 CD CD-II CE CF CF-2 CF-4 CG-4 CH-4 E0-M PLUS 20071 VDS VDS-2 SH SJ SL GF-3 conserving C-4

APPENDIX

Engine and Transmission Lubricants Recommendations by Specifications and Grade

12.14

Product

R=RECOMMENDED FOR THE CORRESPONDING SPECIFICATION CATEGORY. * YOU MUST CONSULT YOUR OWNERS’ MANUAL FOR APPLICABILITY OF THIS PRODUCT.

R R R R R

R R

FormulaShell 5W-30 10W-30 10W-40 30 40

R R

R R R R R

R R R

R R

R R R

R* R R R

R R

R R

R* R R

R R

R R

R* R R

R R


R R R

R R


FormulaShell Synthetic Blend 5W-20 5W-30 10W-30 20W-50

FormulaShell 100% Synthetic 5W-30 10W-30


APPENDIX


R R R R

R

R

R R

R R R R

R


R

R

TG

R R

Allison C-4

Donax TC TD TDL

Product

R

Cat TO-2

R

Cat TO-4

TRANSMISSION OILS

10W-30 15W-40 10W 30

Shell Fleet

Product

R R

R R

R R

R R

R R R R R

R=RECOMMENDED FOR THE CORRESPONDING SPECIFICATION CATEGORY.

R R R R R


R R R R


APPENDIX


12.15

APPENDIX Grease Thickeners Greases generally consist of a base oil with additives plus a thickening agent to create the semi-solid nature of a grease. The thickeners may contain lithium, calcium, aluminum or barium components or be made of polyurea or clay etc. “Complex” greases are a newer type of thickener technology (than “Simple Soap”) and tend to improve the high temperature capability of the grease. About Shell Canada’s major greases: Lithium soap greases have been around for many years and their multipurpose nature allows them to satisfy over 80% of all applications. However, for severe applications, other technologies may have advantages. Lithium Complex greases maintain most of the multipurpose nature of lithium greases but perform better at high temperatures and can have better mechanical stability. In general,“Complex” greases tend to have greater compatibility problems with other greases than conventional soap greases. Calcium soap greases have better water resistance and mechanical stability than lithium greases, but are not suitable for high temperatures. Mixed Lithium Calcium greases combine the advantage of both technologies, with excellent high temperature and mechanical stability properties. “Microgel” clay greases are excellent multipurpose products with extreme high temperature and mechanical stability capabilities. Polyurea greases have excellent long life and natural antiwear properties but are better suited to some specialized applications rather than multipurpose use.

12.16

APPENDIX Grease Compatibility Different greases may not be compatible with each other. Incompatibility may be caused by the different thickening agents used or by the different additives used in greases. Thickener incompatibility usually results in the mixture becoming thinner than anticipated. Other detrimental effects are possible. Due to the complexity of this problem and its potential seriousness, and as opinions vary as to which types of greases are compatible, we have chosen not to include a grease compatibility chart. “RULE OF THUMB” As a general rule of thumb, it is best to assume that all different types and brands of greases are NOT COMPATIBLE with each other. When changing from one grease to another it is best to completely clean the grease cavity and lubricated surfaces. If this is not possible, a thorough purge of the system should be performed. Incompatibility problems are more critical in equipment operating at higher temperatures, speeds and loads. SHELL CANADA’S GREASES The Lithium, Calcium and mixed Lithium-Calcium greases, as manufactured by Shell Canada, are compatible with each other and our “Microgel” clay based greases. Clay based greases can be incompatible with a wide range of thickeners and additive technologies but Shell Canada’s Research has improved this technology beyond that of other clay based greases, such that compatibility problems are much less of an issue. For further information on specific grease compatibility, contact the Shell Helps Centre at 1-800-661-1600.

12.17

APPENDIX NLGI Grease Grading System/Service Classifications

NLGI GREASE SERVICE CLASSIFICATIONS NLGI Grade #

WORKED PENETRATION (10th of mm) @ 25°C

000

445 to 475 (measured with alternate cone) (very soft, semi-fluid)

00

400 to 430 (measured with alternate cone)

0

355 to 385

1

310 to 340

2

265 to 295

3

220 to 250

4

175 to 205

5

130 to 160

6

85 to 115 (very hard, block grease)

Note: Gaps exist (in the penetration numbers) between the official NLGI grades. This allows for unofficial half grades e.g.) a grease with a penetration of 300mm could be designated as a 1.5 grade.

NLGI GREASE SERVICE CLASSIFICATIONS LA - (Chassis)

Mild duty, frequent relubrication

LB - (Chassis)

High loads, water exposure, infrequent relubrication

GA - (Wheel Bearings)

Mild duty

GB - (Wheel Bearings)

Moderate duty, typical of most vehicles

GC - (Wheel Bearings)

Severe duty, high temperature, frequent stop and go service

12.18

APPENDIX Comparable Viscosity Grades 900

50

850

42

775

40

700

680

38

8

36

625 140

550

34 32

500 450

460

7

30

400

28

365

26

315

320

24

6

22

280 Viscosity cSt. @ 40°C 205

90 220

5

150

4

115

100

3

85

68

60

2

46

1

40

40

32

20

22

16 14

85W

30

Viscosity cSt. @ 100°C 18

175 140

50

12 30

8

80W 20 75W

10

10W 5W

6 4 2

10 0

0 ISO Grade

AGMA No.

SAE Gear Oil

SAE Motor Oil 12.19

APPENDIX Viscosity Conversions (Older SUS or SSU to current cSt. or mm2/s)

Assumes that viscosities are at the same temperature and the Viscosity Index is 95. 35 SSU ~ 40 SSU ~ 45 SSU ~ 50 SSU ~ 55 SSU ~ 60 SSU ~ 65 SSU ~ 70 SSU ~ 75 SSU ~ 80 SSU ~ 85 SSU ~ 90 SSU ~ 95 SSU ~ 100 SSU ~ 110 SSU ~ 120 SSU ~ 130 SSU ~ 140 SSU ~ 150 SSU ~ 160 SSU ~ 170 SSU ~ 180 SSU ~ 190 SSU ~ 200 SSU ~ 225 SSU ~ 250 SSU ~ 275 SSU ~ 300 SSU ~ 325 SSU ~ 350 SSU ~ 375 SSU ~ 400 SSU ~ 425 SSU ~ 450 SSU ~ 475 SSU ~ 500 SSU ~ 12.20

2.5 cSt 4.2 cSt 5.8 cSt 7.4 cSt 8.8 cSt 10.4 cSt 11.8 cSt 13.1 cSt 14.4 cSt 15.6 cSt 17.0 cSt 18.3 cSt 19.4 cSt 20.6 cSt 22.9 cSt 25.2 cSt 27.5 cSt 29.7 cSt 31.9 cSt 34.2 cSt 36.5 cSt 38.6 cSt 40.8 cSt 43.0 cSt 48.5 cSt 53.8 cSt 59.2 cSt 64.8 cSt 70.1 cSt 75.6 cSt 81.1 cSt 86.5 cSt 92.0 cSt 97.4 cSt 102.7 cSt 108.0 cSt

550 SSU ~ 600 SSU ~ 650 SSU ~ 700 SSU ~ 750 SSU ~ 800 SSU ~ 850 SSU ~ 900 SSU ~ 1,000 SSU ~ 1,100 SSU ~ 1,200 SSU ~ 1,300 SSU ~ 1,400 SSU ~ 1,500 SSU ~ 1,600 SSU ~ 1,700 SSU ~ 1,800 SSU ~ 1,900 SSU ~ 2,000 SSU ~ 2,100 SSU ~ 2,200 SSU ~ 2,300 SSU ~ 2,400 SSU ~ 2,500 SSU ~ 2,600 SSU ~ 2,700 SSU ~ 2,800 SSU ~ 2,900 SSU ~ 3,000 SSU ~ 3,500 SSU ~ 4,000 SSU ~ 5,000 SSU ~ 6,000 SSU ~ 7,000 SSU ~ 8,000 SSU ~ 9,000 SSU ~

119 cSt 129 cSt 140 cSt 151 cSt 162 cSt 173 cSt 183 cSt 195 cSt 216 cSt 237 cSt 259 cSt 280 cSt 302 cSt 324 cSt 345 cSt 368 cSt 389 cSt 411 cSt 432 cSt 453 cSt 475 cSt 496 cSt 518 cSt 539 cSt 562 cSt 584 cSt 605 cSt 627 cSt 648 cSt 756 cSt 864 cSt 1,080 cSt 1,296 cSt 1,509 cSt 1,726 cSt 1,943 cSt

APPENDIX ISO Viscosity Grades VISCOSITY SYSTEM FOR INDUSTRIAL LUBRICANTS - ASTM D-2422-86

ISO Grade

Mid-Point Viscosity CSt @ 40°C

Minimum Of Grade

Maximum Of Grade

AGMA (Gear) Number

VG 2

2.2

1.98

2.4

VG 3

3.2

2.88

3.52

VG 5

4.6

4.14

5.06

VG 7

6.8

6.12

7.48

VG 10

10

9

11

VG 15

15

13.5

16.5

VG 22

22

19.8

24.2

VG 32

32

28.8

35.2

VG 46

46

41.4

50.6

1

VG 68

68

61.2

74.8

2

VG 100

100

90

110

3

VG 150

150

135

165

4

VG 220

220

198

242

5

VG 320

320

288

352

6

VG 460

460

414

506

7

VG 680

680

612

748

8

VG 1000

1000

900

1100

8A

VG 1500

1500

1350

1650

12.21

APPENDIX API Gravities and Densities Note: All conversions are at 15.6°C. API Gravity

Density (kg/L)

API Gravity

Density (kg/L)

0

1.074

21

0.926

1

1.066

22

0.920

2

1.058

23

0.914

3

1.050

24

0.908

4

1.042

25

0.902

5

1.034

26

0.896

6

1.027

27

0.891

7

1.020

28

0.885

8

1.012

29

0.880

9

1.005

30

0.874

10

0.998

31

0.869

11

0.991

32

0.864

12

0.984

33

0.858

13

0.977

34

0.853

14

0.970

35

0.848

15

0.964

36

0.843

16

0.957

37

0.838

17

0.951

38

0.833

18

0.944

39

0.828

19

0.938

40

0.823

20

0.932

41

0.818

12.22

APPENDIX Conversion Factors Linear Measurement: 1 inch = 25.4 mm 1 foot = 0.3048 meters 1 yard = 0.9144 meters 1 mile = 1.6093 km 1 nautical mile = 1.852 km Area Measurement: 1 sq. inch = 6.4516 sq. cm 1 sq. foot = 0.09290 sq. m 1 sq. yard = 0.8361 sq. m 1 sq. mile = 2.5899 sq. km 1 acre = 0.4047 hectares

1 mm = 0.03937 inches 1 cm = 0.3937 inches 1 m = 39.37 inches 1 km = 0.6214 miles

1 sq. cm = 0.1550 sq. inches 1 sq. m = 10.7639 sq.feet 1 sq. m = 1.1960 sq. yards 1 sq. km = 0.3861 sq. miles 1 hectare = 2.471 acres

Cubic Measurement: 1 cu. inch = 16.3871 cc (ml) 1 cc (ml) = 0.061024 cu. inches 1 cu. foot = 0.02832 cu. m 1 cu. m = 35.3147 cu. feet 1 cu. foot = 28.3161 litres 1 litre = 0.0353 cu. feet 1 cu. yard = 0.7646 cu. m 1 cu. m = 1.3080 cu. yards Volume Conversions: 1 Imp.gallon = 4.546 litres = 1.20092 U.S. gallons = 0.00456 cubic metres = 0.028594 Bbls (barrels) = 0.160544 cu.feet 1 litre

= 0.21998 Imp. gallons = 0.26417 U.S. gallons = 0.001000 cubic metres = 0.006290 Bbls. = 0.0353157 cu. feet

1 cu. m = 1000 litres 1 cu. inch = 16.4 cc (ml) 1 Bbl. = 159 litres Temperature Conversion: °F = (°C x 9/5) + 32 °C = (°F - 32) x 5/9 Pressure Conversion: 100 kPa = 14.504 PSI = 1 bar

12.23

APPENDIX Table of Temperature Conversions

°C

°F

°C

°F

°C

°F

°C

°F

-70

-94.0

-46

-50.8

-22

-7.6

2

35.6

-69

-92.2

-45

-49.0

-21

-5.8

3

37.4

-68

-90.4

-44

-47.2

-20

-4.0

4

39.2

-67

-88.6

-43

-45.4

-19

-2.2

5

41.0

-66

-86.8

-42

-43.6

-18

-0.4

6

42.8

-65

-85.0

-41

-41.8

-17

1.4

7

44.6

-64

-83.2

-40

-40.0

-16

3.2

8

46.4

-63

-81.4

-39

-38.2

-15

5.0

9

48.2

-62

-79.6

-38

-36.4

-14

6.8

10

50.0

-61

-77.8

-37

-34.6

-13

8.6

11

51.8

-60

-76.0

-36

-32.8

-12

10.4

12

53.6

-59

-74.2

-35

-31.0

-11

12.2

13

55.4

-58

-72.4

-34

-29.2

-10

14.0

14

57.2

-57

-70.6

-33

-37.4

-9

15.8

15

59.0

-56

-68.8

-32

-25.6

-8

17.6

16

60.8

-55

-67.0

-31

-23.8

-7

19.4

17

62.6

-54

-65.2

-30

-22.0

-6

21.2

18

64.4

-53

-63.4

-29

-20.2

-5

23.0

19

66.2

-52

-61.6

-28

-18.3

-4

24.8

20

68.0

-51

-59.8

-27

-16.6

-3

26.6

21

69.8

-50

-58.0

-26

-14.8

-2

28.4

22

71.6

-49

-56.2

-25

-13.0

-1

30.2

23

73.4

-48

-54.4

-24

-11.2

0

32.0

24

75.2

-47

-52.6

-23

-9.4

1

33.8

25

77.0

12.24


°C

°F

°C

°F

°C

°F

°C

°F

26

78.8

50

122.0

74

165.2

98

208.4

27

80.6

51

123.8

75

167.0

99

210.2

28

82.4

52

125.6

76

168.8

100

212.0

29

84.2

53

127.4

77

170.6

101

213.8

30

86.0

54

129.2

78

172.4

102

215.6

31

87.8

55

131.0

79

174.2

103

217.4

32

89.6

56

132.8

80

176.0

104

219.2

33

91.4

57

134.6

81

177.8

105

221.0

34

93.2

58

136.4

82

179.6

106

222.8

35

95.0

59

138.2

83

181.4

107

224.6

36

96.8

60

140.0

84

183.2

108

226.4

37

98.6

61

141.8

85

185.0

109

228.2

38

100.4

62

143.6

86

186.8

110

230.0

39

102.2

63

145.4

87

188.6

111

231.8

40

104.0

64

147.2

88

190.4

112

233.6

41

105.8

65

149.0

89

192.2

113

235.4

42

107.6

66

150.8

90

194.0

114

237.2

43

109.4

67

152.6

91

195.8

115

239.0

44

111.2

68

154.4

92

197.6

116

240.8

45

113.0

69

156.2

93

199.4

117

242.6

46

114.8

70

158.0

94

201.2

118

244.4

47

116.6

71

159.8

95

203.0

119

246.2

48

118.4

72

161.6

96

204.8

120

248.0

49

120.2

73

163.4

97

206.6

121

249.8

12.25


°C

°F

°C

°F

°C

°F

°C

°F

122

251.6

146

294.8

170

338.0

194

381.2

123

253.4

147

296.6

171

339.8

195

383.0

124

255.2

148

298.4

172

341.6

196

384.8

125

257.0

149

300.2

173

343.4

197

386.6

126

258.8

150

302.0

174

345.2

198

388.4

127

260.6

151

303.8

175

347.0

199

390.2

128

262.4

152

305.6

176

348.8

200

392.0

129

264.2

153

307.4

177

350.6

201

393.8

130

266.0

154

309.2

178

352.4

202

395.6

131

267.8

155

311.0

179

354.2

203

397.4

132

269.6

156

312.8

180

356.0

204

399.2

133

271.4

157

314.6

181

357.8

205

401.0

134

273.2

158

316.4

182

359.6

206

402.8

135

275.0

159

318.2

183

361.4

207

404.6

136

276.8

160

320.0

184

363.2

208

406.4

137

278.6

161

321.8

185

365.0

209

408.2

138

280.4

162

323.6

186

366.8

210

410.0

139

282.2

163

325.4

187

368.6

211

411.6

140

284.0

164

327.2

188

370.4

212

413.6

141

285.8

165

329.0

189

372.2

213

415.4

142

287.6

166

330.8

190

374.0

214

417.2

143

289.4

167

332.6

191

375.8

215

419.0

144

291.2

168

334.4

192

377.6

216

420.8

145

293.0

169

336.2

193

379.4

217

422.6

12.26

PRODUCT INDEX

Product

Page

13.1

PRODUCT INDEX

Advance Premium Snowmobile . . see Shell Advance Prem. Snowmobile Advance 100% Synthetic Chain Case Oil . . . . . . . . . . . . . 10.6 Advance Snow Ultra. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4 Advance Snow Ultra Grease . . . . . . . . . . . . . . . . . . . . . . . 6.4 AeroShell Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7 AeroShell Greases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6 AeroShell Oils (non-dispersant) . . . . . . . . . . . . . . . . . . . . 4.3 AeroShell Turbine Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8 AeroShell Oil W 15W-50 (semi-synthetic) . . . . . . . . . . . . . 4.5 AeroShell Oil W 100 Plus . . . . . . . . . . . . . . . . . . . . . . . . . 4.6 AeroShell Oil W Piston Engine Oils (dispersant). . . . . 4.4 Albida LC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.8 Alexia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2 Alvania EP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.12 Alvania EP D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.10 Alvania 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.14 Argina . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3 Caprinus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4 Cardura . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.15 Cassis A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.4 Chain Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7 Classlube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5 Clavus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.6 Clavus AB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 Clavus HFC 68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.8 Corena AS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.10 Corena DE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.12 Corena NG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.14 Corena P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.16 Corena S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.18 Cyprina RA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.17 Darina AX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.18 Darina XL EP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.20 Decol H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.19 Delima. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.20 Delima R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.21 Dentax 80W-90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.26 Dentax S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.29

PRODUCT INDEX

Product

Page

Diala A and AX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.22 Diamond Drill Rod. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.22 Donax CFD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.11 Donax TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6 Donax TD and TDL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8 Donax TF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9 Donax TG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.10 Dromus B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.24 Dursol K1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.23 Form Oil 46 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.25 FormulaShell Engine Oils (mineral and synthetic blend). . 3.12 FormulaShell Engine Oils (100% synthetic) . . . . . . . . . . . 3.14 FormulaShell SAE 30 and SAE 40 . . . . . . . . . . . . . . . . . . . 3.15 Gadinia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.6 Garia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.26 Geartherm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.27 Hyperia S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.28 Indusol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see Shell Indusol Malleus GL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.24 Malleus TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.26 Melina . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7 Morlina . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.30 Mysella . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.31 Nautilus Premium Outboard Motor Oil . . . . . . . . . . . . . . 10.8 Nautilus Biodegradable Bilge Cleaner . . . . . . . . . . . . . . . . 10.13 Nautilus Biodegradable Boat Cleaner . . . . . . . . . . . . . . . . 10.14 Nautilus Biodegradable Outboard Motor Oil. . . . . . . . . . . 10.9 Nautilus 4 Stroke Engine Oils. . . . . . . . . . . . . . . . . . . . . . 10.10 Nautilus Jet Pump Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.15 Nautilus Marine Gear Oil . . . . . . . . . . . . . . . . . . . . . . . . . 10.12 Nautilus Personal Watercraft Oil. . . . . . . . . . . . . . . . . . . . 10.17 Nautilus Synthetic Gear Oil . . . . . . . . . . . . . . . . . . . . . . . 10.16 No Fire WG 200R. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.36 Omala . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.38 Omala HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.40 Omala RL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.41 Ossagol C Moly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.27 Pella A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.42 Retinax TL 00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.28 13.2

PRODUCT INDEX

Product

Page

Rotella ELC Extended Life Coolant . . . . . . . . . . . . . . . . . 3.5 Rotella T Single Grade . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.18 Rotella T Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.24 Rotella T SB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.22 Rotella T with XLA (multi-grade) . . . . . . . . . . . . . . . . . . . 3.20 Sawguide Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.43 Shell Advance Premium Snowmobile . . . . . . . . . . . . . . . . 10.3 Shell Fleet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.16 Shell Fluid FM 32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3 Shell FM Grease 1.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.16 Shell FR-N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.34 Shell Indusol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.29 Shell LGF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7 Shell Naturelle HF-E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.32 Shell Naturelle HF-M . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.33 Shell Turbo T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.58 Shellflex Naphthenic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2 Shellflex Paraffinic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.4 Shellzone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4 Sirius FB Oil 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.8 Spirax HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.26 Spirax S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.28 SRS 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.30 Stringol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.44 Surstay EP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.32 Tellus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.46 Tellus 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.45 Tellus HD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.48 Tellus T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.50 Thermia C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.52 Tivela. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.53 Tonna V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.54 Torcula . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.56 Turbo T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see Shell Turbo T Ultragel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.33 Valvata . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.60 Vitrea 22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.61 VSI 68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.62 XTC-50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.18 13.3

Contact us for more information on Shell Lubricants: Shell Helps Centre

1-800-661-1600 www.shell.ca

275-S-000277

Handbook of Lubricants

Recommend Documents