para poner en marcha equipo de telecomunicacion de redes opticas pasivas PON
para poner en marcha equipo de telecomunicacion de redes opticas pasivas PON
examen tipoDescripción completa
Seguridad de Redes VlansDescripción completa
Descripción completa
Manual con los pasos basicos para configurar Mikrotik
Descripción completa
Ejercicios de Química General sobre la Configuración Electrónica
Descripción: Mikrotik procedimiento para usar The dude mikrotik en windows 7
Descripción completa
Descripción completa
plan de configuracionDescripción completa
vpn y vlansDescripción completa
configuracion de ripDescripción completa
Nociones de configuracion CADWORXDescripción completa
CREANDO LA BASE DE DATOS DE LAS VLAN
SW-ACCESO-1>en SW-ACCESO-1#vlan database % Warning: It is recommended to configure VLAN from config mode, as VLAN database mode is being deprecated. Please consult user documentation for configuring VTP/VLAN in config mode. SW-ACCESO-1(vlan)#vlan 10 name ventas VLAN 10 modified: Name: ventas SW-ACCESO-1(vlan)#vlan 20 name admon VLAN 20 modified: Name: admon SW-ACCESO-1(vlan)#vlan 30 name informatica VLAN 30 modified: Name: informatica SW-ACCESO-1(vlan)#
ASIGNACIÓN DE PUERTOS A LAS VLAN
SW-ACCESO-1#conf t Enter configuration commands, one per line. End with CNTL/Z. SW-ACCESO-1(config)#int range f0/5 -10 SW-ACCESO-1(config-if-range)#switchport mode access SW-ACCESO-1(config-if-range)#switchport access vlan 10 SW-ACCESO-1(config-if-range)#int range f0/11-17 SW-ACCESO-1(config-if-range)#switchport mode access SW-ACCESO-1(config-if-range)#switchport access vlan 20 SW-ACCESO-1(config-if-range)#int range f0/18-24 SW-ACCESO-1(config-if-range)#switchport mode access SW-ACCESO-1(config-if-range)#switchport access vlan 30 SW-ACCESO-1(config-if-range)#exit SW-ACCESO-1(config)#exit
VERIFICANDO LA CONFIGURACIÓN DE LAS VLAN Y LOS PUERTOS ASIGNADOS CON EL COMANDO “SHOW VLAN”
ASIGNACIÓN DEL ENLACE TRUNK EN EL SWITCH:
SW-ACCESO-1#conf t Enter configuration commands, one per line. End with CNTL/Z. SW-ACCESO-1(config)#inter range f0/1-4 SW-ACCESO-1(config-if-range)#switchport mode trunk SW-ACCESO-1(config-if-range)#exit SW-ACCESO-1(config)#exit %SYS-5-CONFIG_I: Configured from console by console SW-ACCESO-1#wr Building configuration... [OK]
VERIFICANDO EL ENLACE TRUNK:
ENCENDIENDO LA INTERFAZ FÍSICA DEL ROUTER
ASIGNACIÓN DE RESPECTIVAS SUB INTERFACES A CADA VLAN EN EL ROUTER
Router(config-if)#interf f0/0.10 %LINK-5-CHANGED: Interface FastEthernet0/0.10, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.10, changed state to up Router(config-subif)#encapsulation dot1q 10 Router(config-subif)#ip add 172.16.0.1 255.255.255.0 Router(config-subif)#interf f0/0.20 %LINK-5-CHANGED: Interface FastEthernet0/0.20, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.20, changed state to up Router(config-subif)#encapsulation dot1q 20 Router(config-subif)#ip add 172.16.1.1 255.255.255.128 Router(config-subif)#interf f0/0.30 %LINK-5-CHANGED: Interface FastEthernet0/0.30, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.30, changed state to up Router(config-subif)#encapsulation dot1q 30 Router(config-subif)#ip add 172.16.1.129 255.255.255.192
Router(config-subif)#encapsulation dot1q 30 Router(config-subif)#ip add 172.16.1.129 255.255.255.192 Router(config-subif)#end Router# %SYS-5-CONFIG_I: Configured from console by console
GUARDANDO LA CONFIGURACION EN EL ROUTER CON EL COMANDO “WR”
Router#wr Building configuration... [OK]
VEIFICANDO LA CONFIGURACIÓN DE LAS VLAN EN EL ROUTER CON “SHOW RUN”
Router#sh run Building configuration... Current configuration : 746 bytes ! version 12.4 no service timestamps log datetime msec no service timestamps debug datetime msec no service password-encryption ! hostname Router interface FastEthernet0/0 no ip address
duplex auto speed auto ! interface FastEthernet0/0.10 encapsulation dot1Q 10 ip address 172.16.0.1 255.255.255.0 ! interface FastEthernet0/0.20 encapsulation dot1Q 20 ip address 172.16.1.1 255.255.255.128 ! interface FastEthernet0/0.30 encapsulation dot1Q 30 ip address 172.16.1.129 255.255.255.192 ! interface FastEthernet0/1 no ip address duplex auto speed auto shutdown ! interface Vlan1 no ip address shutdown
EL SIGUIENTE PASO ES IR A CADA PC DE CADA VLAN
Escritorio=>IP configuración y Static Cada PC debe tener una respectiva IP, mascara de subred y Gateway. Según la vlan a la que corresponda