Back
GPS PLOTTER GP-1850/W Series
The paper used in this manual is elemental chlorine free.
・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax
: +81-(0)798-65-4200
All rights reserved.
Printed in Japan
A : DEC . 2002 A2 : AUG . 22, 2008
Pub. No. SME-43950-A2 (KAOK )
GP-1850/1850W SER.
*00080992600* *00080992600* * 0 0 0 8 0 9 9 2 6 0 0 *
Table of Contents 1. General …………………………………………………………. 1 2. Difference between GP-1850 and GP-1850W …..…………. 1 3. Difference between D, F and DF ……………………….……. 2 4. Replacing major parts …………………………………………. 2 5. How to install DGPS beacon receiver………..…………….… 4 6. Replacing lithium battery ……………………………………… 4 7. How to change software to C-MAP version ………..……..… 5 8. How to upgrade system program …….…………….……..…… 7 9. Troubleshooting …………………………………………………… 8 9.1 Self test ……………………………………………………. 8 9.2 Troubleshoot guide ………………..……………………….. 9
Exploded View…………………………….………………………… D-1 Electrical Parts List Schematic Diagrams
………………………………………………… E-1 ……………………………………………… S-1
i
This page is intentionally left blank.
1. General The GP-1850/W series display unit consists of the following components. Parts Name MAIN board
ANLG board PNL board GPS receiver BEACON receiver LCD unit
Function The board, heart of the unit consits of a CPU, ROM, RAM, Card Interface circuit, a buzzer and a lithium battery. The board generates high voltage for LCD backlighting. The difference between A, B, E, and F is system program only. The board includes power supply and echosounder circuits. The board consists of key switches and backlight LEDs. The receiver receives and processes satellite signal for position fix. The receiver receives radiobeacon DGPS to remove errors in GPS position fix. High voltage for LCD backlighting is derived from J101 on MAIN board to Cold Cathode Fluorescent Light (CCFL) in the LCD unit.
TX Output signal of echosounder circuit 50 kHz and 200 kHz transmitters in echosounder circuit on 14P0313B board outputs the following signal to the transducer. Range setting: 1200 m 50 kHz: 20 to 25 Vpp
Oscilloscope setting:
200 kHz: 27 to 32 Vpp
5 V/div, 200 us/div
(600 W)
Test points: Pins 8 and 10 on J2 (with XDR connected)
0.2 ms
Fig.1
TX waveform of echosounder
2. Difference between GP-1850 and GP-1850W MAIN boards, 14P0311X and 14P0311XW are the same in hardware, but not in software. Component MAIN board GPS receiver
LCD unit LCD protective panel ANLG board PNL board BEACON receiver
GP-1850 GP-1850W 14P0311X 14P0311XW (Not supporting WAAS) (Supporting WAAS) GN7707 (original) GN8091 GN7801 (compatible with (Supporting WAAS) GN7707) EDTCA-03QCF EDTCA-03QCF-AR Acrylic plate AR acrylic plate 14P0313 14P0312 GR-8020 (original), GR-7000A (Jan. 2000 and after) 1
3. Difference between D, F and DF The letter D in the model indicates that the beacon receiver for differencial correction of GPS receiver is buit in the unit. The letter F indicates that the unit features echosounder capability. 14P0311C(W) and D(W) a re for Japanese version.
MAIN board
GP-1850(W) 14P0311A(W) 14P0311E(W) 14P0313A Not buit-in
ANLG board BEACON receiver Key top (right XTE HIWAY to PLOT key)
GP-1850D(W) 14P0311A(W) 14P0311E(W) 14P0313A Built-in
GP-1850F(W) 14P0311B(W) 14P0311F(W) 14P0313B Not buit-in
GP-1850DF(W) 14P0311B(W) 14P0311F(W) 14P0313B Built-in
XTE HIWAY
SNDR
SNDR
4. Replacing major parts To replce the major parts, follow the steps below. 1. Place the unit on soft surface – face down. Remove all nuts (arrowed in Fig.2) and 12 screws (ringed) fixing the cover to the front panel. Then, lift the cover. Fig.3 shows GP-1850/W series display unit with the cover removed.
Fig. 2
GP-1850/W series display unit, rear view
ANLG board (14P0313A/B) Connectors: ANT, XDR*, DGPS, NMEA and PWR, from left *: only F version
Fig.3
Do not lose connector gaskets!
GP-1850/W series display unit with cover removed 2
2. Remove the screw fixing the GND wire to MAIN board. Then, pull ANLG board assembly straight upward.
GND wire
Fig.4
GP-1850/W series display unit with cover removed, top view
3. Remove the shield cover, and unplug J2, J4 and J6 on MAIN board. The MAIN board is battery backupped, so it is recommended that before removing MAIN board, disconnect either lead of JP6 not to damage the components on the board by a short circuit. With JP6 disconnected, the board is not battery backupped. Lithium battery at soldering side MAIN board, 14P0311
JP6 J2
J4 (Release locking tab by pushing it toward cable.)
J6 (Release locking tab by pushing it toward cable.)
LCD unit mounting plate with LCD unit on the back
Fig.5
MAIN board, 14P0311
Now the LCD unit can also be removed together with the mounting plate.
3
5. How to install DGPS beacon receiver Refer to the installation manual.
6. Replacing lithium battery To replace the battery with new one, follow the steps below. 1. Disconnect JP6 on MAIN board. See Fig.5. 2. Use a desoldering tool to remove the battery from MAIN board. 3. Solder the replacement battery onto the board. 4. Solder JP6. CAUTION 1) Replace the battery only with CR2450-F2 ST2L (000-144-941). 2) Never short + and – sides of the cell. 3) The lithium cell may explode resulting in a fire or chemical burn if mistreated. Do not recharge, disassemble heat, or incinerate. 4) Follow local ordinances or regulations for the disposal.
Lithium Battery Type: CR2450-F2ST2L C/N: 000-144-941
Fig.6
MAIN board, soldering side
4
7. How to change software to C-MAP version GP-1640 sereis uses following programs. Navionics version 14518260XX 14518270XX 14518260XX 14518270XX
GP-1850/D : GP-1850F/DF: GP-1850W/WD: GP-1850WF/WDF
C-MAP version 14518400XX 14518410XX 14518400XX 14518410XX
1) By using PC The following explains how to upgrade the software by using a PC. The “up boot” upgradation is carried out only when requested. Before upgradation The batch file “up_boot. bat” is designed for the use of COM2 port of the PC. When COM 1 port is used, the batch file needs to be modified by using a text editor application such as Note Pad. The last number is changed from “2” to “1” when COM 1 port is used. Uppg load. bin GPXXXX. 0 0 1 0 0 0 2
Procedure 1. Copy all files in EXE files to PC. 2. Connect the COM port of the PC to the DGPS port of the plotter.
DGPS (MJ-7P)
(DSUB 9P) COM 1
PC
<1< <2< <3< <5< <4< <6< <7<
>1> RxD >2> TxD >3> GND >5> DTR >4> DSR >6> RTS >7> CTS >8> >9>
NC NC RD SD PLOTTER NC SG SHIELD
Fig. 7(a) Connection with PC (9 pin Dsub)
5
DGPS (MJ-7P
(DSUB 25P) COM 1 >1> TxD >2> RxD >3> DTR >4> PC DSR >5> GND >7> RTS >6>
<1< <2< <3< <5< <4< <6< <7<
NC NC RD PLOTTER SD NC SG SHIELD
>20>
Fig. 7(b) Connection with PC (25 pin Dsub) 3. Run “up_boot. bat” on PC. The message “TAEGET POWER ON” appears on the display. 5. Turn on the plotter. You hear three beeps (pi pi pi) and the message “Execute STEP1” appears. 6. Then a beep sounds and the message “Execute STEP2” appears. It takes about 5 minutes to complete steps 4 and 5. 7. When the message “Finish version up” appears, the upgradation of the boot software is completed. 8. Turn off the plotter. If the up-boot procedure fails, the plotter must be reset by downloading the software from a master program card. 8. Run CTOOL_E.EXE on PC. The CTOOL_E.EXE creates following files. Models GP-1850/1850D GP-1850W/1850WD GP-1850F/1850DF GP-1850WF/1850WDF
File name 1850e. BAT, CU1850e. BAT, LOAD. BIN, UPPG EXE 1640fe. BAT, CU1850fe. BAT, LOAD. BIN, UPPG EXE
9. Run either batch file, C1850 BAT or C185e.BAT according to the model to get the binary file (Cxxxe.BIN). 10. Then, run either batch file, CU1850e. BAT or CU1850fe.BAT according to the model. 11. Turn on the plotter when the message “TARGET POWER ON” appears on the PC.
6
2) By using program master card The following describes how to update the software by using the master card. 1. Insert Program master card into the slot. 2. Turn on the power. “NOW LOADING” message appears. 3. When loading is completed, the message “PLEASE REMOVE A CARD AFTER POWER SUPPLY CUTS” appears on the display. Then, the power is automatically turned off. If the power is turned off without the message, the program loading is failed. Repeat above steps.
8. How to upgrade system program The software is updated by following the procedure below. 1) By using PC Take steps 8 to 11 in the previous section. The Navionics version program files do not include a letter C. 2) By using program master card The procedure is the same as the previous section.
7
9. Troubleshooting
Caution - High Voltage! In GP-1850F/DF/WF/WDF, high voltage presents at leads of R116.
Fig.8
R116
R116 on ANLG board, 14P0313B
9.1 Self test Self test is performed by following the steps bellow. 1. Press [MENU] key to open the main menu. 2. Press CONFIGURATION soft key to show the configuration menu. 3. Press the SYTEM MENU soft key to open the system menu. 4. Press SELF TEST soft key to open test menu. 5. Press MEMORY I/O TEST soft key to start the test. The following describes the test result display. PROGRAM: S ystem program sum check is performed. SRAM: Read/write test for SRAM on MAIN board is performed. DRAM: Read/write test for DRAM on MAIN board is performed. PORT 1: Loopback test is performed for NMEA port interface circuit connecting pin 1 to pin 3 and pin 2 to pin 4. This line reads without jumpers on NMEA port. PORT 2: Loopback test is performed for DGPS port interface circuit connecting pin 5 to pin 3. This line reads - - without a jumper DGPS port.
by - by on
INTERNAL BATTERY: NG is displayed when voltage of lithium battery on MAIN board lowers to 2.5 V. GPS RECEIVER: GPS receiver is tested. Program nubmer for GPS receiver is 48502370XX.
8
9.2 Troubleshoot guide Table below provides a problem symptom, followed by a possible solution. Symptom
Possible solution
Failure to power
Check 5A in-line power cable fuse and F1(7A) on ANLG board.
No buzzer sound
Replace MAIN board.
Problems on indication LCD not backlighted
Replace MAIN board. Replace MAIN board and/or LCD unit. Voltage at J2 on MAIN board is about 2400 Vpp (850 Vrms) AC. Replace MAIN and/or ANLG board.
No sounder picture
R88 adjusts 5 V line.
Fuse, 7 A, 125V
R104 adjusts switching frequency of 83 kHz.
Fig.9
ANLG board, 14P0313A/B
Antenna connector
JP1 for output power selection #1 - #2: 600 W #3 - #4: 1 kW
Fig. 10
Jumper blcok, JP1 on ANLG board 9
This page is intentionally left blank.
D-1 LCD EDTCA-03QCF (000-140-673)
パネル部組品 PANELASSY. GP-1850/D(J) (000-146-459) GP-1850/D(E) (000-146-460) GP-1850F/DF(J) (000-146-461) GP-1850F/DF(E) (000-146-462)
MAINBOARD 14P0311A(1850/DNAVIONICS-E) 14P0311B(1850F/DFNAVIONICS-E) 14P0311C(1850/DNAVIONICS-J) 14P0311D(1850F/DFNAVIONICS-J) 14P0311E(1850/DC-MAP-E) 14P0311F(1850F/DFC-MAP-E)
B
ﾊﾝｶﾞｰ組品 BRACKET ASSY. GP-1850/D/F/DF (000-790-434)
A
パネル部組品 FRONTBEZ ELWITHFILTER GP-1850/D /F/DF (000-146463)
ﾗﾊﾞｰｷｰ(E2)/(E2F)(J2)(J2F) RUBBERKEY(E2)/(E2F)(J2)(J2F) ﾗﾊﾞｰｷｰJ1/E1 14-063-1003 RUBBERKEYJ1/E1 (100-270-610)-1850F/DF-E 14-063-1002(E) 14-063-1004 (100-270-600) (100-270-620)-1850F/DF-E 14-063-1042(J) 14-063-1043 (100-270-764) (100-270-773)-1850/D-J 14-063-1044 (100-270-783)-1850F/DF-J
PNLBOARD 14P0312 ﾉﾌﾞ KNOB 20-007-2302 (100-173-273)
WARN IN
G
A
ﾊｰﾄﾞｶﾊﾞｰ組品 HARDCOVERASSY. GP-1850/F (000-790-436)
ﾋﾞｰｺﾝ受信機 BEACONRECEIV ER GR-8020or GR-7000A (GP-1850D/DFonly)
GPS受信機 GPSRECIVER GN-7077or GN-7801A
APPROVED
承 認 2002.9.3
CHECKED
B
審 査 2002.9.3
DRAWN
製 図 2002.9.3
桒村 高橋 三好
ANLGBOARD 14P0313A(1850/D) 14P0313B(1850F/DF)
TITLE
GP-1850D GP-1850F/DF DWG. NO.
指示器 DISPLAY UNIT
C4395-E01-C
D-2 B
ﾊﾝｶﾞｰ組品 BRACKETASSY . GP-1850W/WD/ WF/WDF (000-790-434 )
LCD組品 LCDASSY. (004-378-840)
A
パネル部組品 FRONTPANELASSY. GP-1850W/WF (000-790-435)
ﾗﾊﾞｰｷｰ(E2)/(E2F)/(J2)/(J2F) RUBBERKEY(E2)/(E2F)/(J2)/(J2F) 14-063-1003(E) (100-270-610)-1850W/WD 14-063-1004(E) (100-270-620)-1850WF/WDF 14-063-1043(J) (100-270-773)-1850W/WD 14-063-1044(J) (100-270-783)-1850WF/WDF
MAIN基板 MAINBOARD 14P0311AW(1850W/WDNAVIONICS-E) (000-790-426) 14P0311BW(1850WF/WDFNAVIONICS-E) (000-790-427) 14P0311WC(1850W/WDNAVIONICS-J) (000-790-428) 14P0311DW(1850WF/WDFNAVIONICS-J) (000-790-429) 14P0311EW(1850W/WDC-MAP-E) (000-790-430) 14P0311FW(1850WF/WDFC-MAP-E) (000-790-431) PNL基板 PNLBOARD 14P0312 (000-141-996)
ﾉﾌﾞ KNOB 20-007-2302 (100-173-273)
ﾗﾊﾞｰｷｰ(E1)/(J1) RUBBERKEY(E1)/(J1) 14-063-1002(E) (100-270-600) 14-063-1042(J) (100-270-764)
WARN IN
G
A
ﾋﾞｰｺﾝ受信機 (WD/WDF) BEACONRECEIVER GR-7000A (000-143-249)
ﾊｰﾄﾞｶﾊﾞｰ組品 HARDCOVERASSY. GP-1850W/WD/WF/WDF (000-790-436)
GPS受信機 GPSRECEIVER GN-8091C (000-145-613)
APPROVED
承 認 2002.11.8
CHECKED
B
審 査 2002.11.8 DRAWN
製 図 2002.11.8
桒村 高橋 三好
ANLG基板 ANLGBOARD 14P0313A(1850W/WD) (000-141-995) 14P0313B(1850WF/WDF) (000-141-994)
TITLE
GP-1850W/WD GP-1850WF/WDF DWG. NO.
指示器 DISPLAY UNIT
C4425-E01-A
FURUNO
Model Unit
GP-1850/D/F/DF GPSプロッタ GPS PLOTTER Ref.Dwg. C4395-K01-D Blk.No.
電気部品表
ELECTRICAL PARTS LIST 2002年 9月 SYMBOL TYPE
CODE No.
REMARKS
回路記号
ｺｰﾄﾞ番号 プリント基板 000-142-000 000-141-999 000-141-998 000-141-997 000-145-130 000-145-129 000-141-996 000-141-995 000-141-994 000-143-245 000-141-408 000-143-249 000-141-046
備考
1B1
1B2 1B3 1B4 1B7
型式 PRINTED CIRCUIT BOARD 14P0311A, MAIN 14P0311B, MAIN 14P0311C, MAIN 14P0311D, MAIN 14P0311E, MAIN 14P0311F, MAIN 14P0312, PNL 14P0313A, ANLG 14P0313B, ANLG GN-7801A or GN-7707 GR-7000A or GN-8020
PANEL ASSEMBLY GP-1850/D-J GP-1850/D-E GP-1850F/DF-J GP-1850F/DF-E GP-1850/D/F/DF
1B5
1850/D NAVIONICS-E 1850F/DF NAVIONICS-E 1850/D NAVIONICS-J 1850F/DF NAVIONICS-J 1850/D C-MAP-E * 1850F/DF C-MAP-E * 1850/D 1850F/DF
Page
E-1 SHIPPABLE ASSEMBLY 出荷単位組品 X X X X X X X X X
1850D/DF
*: MAIN board for C-Map version will be available made-to-order basis. パネル組品 000-146-459 with rubber key X 000-146-460 with rubber key X 000-146-461 with rubber key X 000-146-462 with rubber key X 000-146-463 BEZEL/FILTER ASSEMBLY X
LCD EDTCA0307CF, LCD
LCD 000-140-673
POWER SUPPLY ASSEMBLY GP-1850 GP-1850F
電源部組品 000-146-457 000-146-458
Power supply unit with ANLG board Power supply unit with ANLG board
FURUNO
Model
GP-1850W/WD/WF/WDF
Unit
GPSプロッタ
Ref.Dwg.
GPS PLOTTER C4325-K01-A
電気部品表 ELECTRICAL PARTS LIST
2002年 11月
Page
E-2
Blk.No.
SYMBOL
TYPE
CODE No.
REMARKS
SHIPPABLE ASSEMBLY
回路記号
型式
ｺｰﾄﾞ番号
備考
出荷単位組品
PRINTED CIRCUIT BOARD
プリント基板
14P0311AW, MAIN
000-790-426
1850W/WD NAVIONICS-E
14P0311BW, MAIN
000-790-427
1850WF/WDF NAVIONICS-E
14P0311CW, MAIN
000-790-428
1850W/WD NAVIONICS-J
14P0311DW, MAIN
000-790-429
1850WF/WDF NAVIONICS-J
14P0311EW, MAIN
000-790-430
1850W/WD C-MAP-E *
14P0311FW, MAIN
000-790-431
1850WF/WDF C-MAP-E *
1B2
14P0312, PNL
000-141-996
1B3
14P0313A, ANLG-A
000-141-995
1850W/WD 1850WF/WDF
1B1
14P0313B, ANLG-B
000-141-994
1B4
GN-8091C
000-145-613
1B7
GR-7000A
000-143-249
1850WD/WDF 1850W/WF(option)
*: MAIN board for C-Map version will be available made-to-order basis.
1B5
PANEL ASSEMBLY
パネル組品
GP-1850W/WF
000-790-435
LCD ASSEMBLY
LCD組品
GP-1850W/WD/WF/WDF
004-378-840
C
B
A
0.2m,φ5.3
DPYC-1.5
*1
５６
１２
（−） 整流器 （＋） RECTIFIER PR-62 *2 *1 IV-8SQ
1 2 3
NOTE *1. LOCAL SUPPLY. *2. OPTION. *3. FITTED AT FACTORY. *4. OPTIONAL LEVEL CONVERTER REQUIRED FOR CURRENT LOOP OR RS422 OUTPUT.
NMEA J6 TD-A TD-B RD-H RD-C NC SHIELD
1 2 3 4 5 6 7
1 2 3 4 5 6
DWG.No.
SCALE
APPROVED
P
アカ RED アオ BLU
C4425-C01- C
MASS
kg
E. MIYOSHI TAKAHASHI. T
P
NMEA0183 Ver 2.0/1.5
4
NAME
名称
TITLE
*4
INTERCONNECTION DIAGRAM
相互結線図 GPS/DGPS PLOTTER
GP-1850W/1850WD GPS/DGPSプロッタ
RD RS-232C NMEA0183 in RS232C LEVEL SHIELD
DGPSビーコン受信機 DGPS BEACON RECEIVER
MJ-A6SPF0007,10m MJ-A6SPF0012,5/10m MJ-A6SPF0011,5/10m MJ-A6SPF003,5m,φ6 シロ WHT クロ BLK キ YEL ミド GRN
MJ-A7SPF0003,5m キ YEL SD
*3 MJ-A7SPFD
P
P
*3 MJ-A6SPF
3
DRAWN Aug. 24, '04 CHECKED
GND *1 IV-1.25SQ.
DGPS J5 NC NC RD NC RS-232C SD NMEA0183 Ver1.5/2.0 SG RTCM104 SHIELD
12-24 VDC J3
(+) (-) SHIELD
J7
ANT
指示器 DISPLAY UNIT GP-1850W/WD
注記 ＊１）現地手配。 ＊２）オプション。 ＊３）コネクタは工場にて取付済み。 ＊４）カレントループ、RS-422の接続にはオプションのレベル変換器が必要。
100/110(115)/ 220/230VAC, 50/60Hz,1φ
12-24 VDC
2
*3 5A MJ-A3SPFD
N-P-8DFB N-J-3 *2 *3 NJTP-3DXV-1 1m,φ5.3
MJ-A3SPF0013,3.5m,φ8.0 シロ WHT クロ BLK
8D-FB-CV *2 30/50m
TNC-PS-3D,15m,φ5.3
*2 *3 NJTP-3DXV-1 1m,φ5.3
*2
*3 TNC-J-3
GPA-017(GP-1850W) GPA-019(GP-1850WD)
10m,φ5.3
GPA-017S(GP-1850W) GPA-019S(GP-1850WD)
TNC-P-3
TNC-P-3
*3 TNC-J-3
空中線部 ANTENNA UNIT
N-J-3 *3 N-P-8DFB
1
*2 TNC-P-3
C
B
A
*2
0.2m,φ5.3
DPYC-1.5 *1
RECTIFIER PR-62 *2
１２ （ −） 整流器 （＋）
５６
*1 IV-8SQ
1 2 3
NOTE *1. LOCAL SUPPLY. *2. OPTION. *3. FITTED AT FACTORY. *4. OPTIONAL LEVEL CONVERTER REQUIRED FOR CURRENT LOOP OR RS422 OUTPUT.
1 2 3 4 5 6 7 8 9 10
DWG.No.
SCALE
APPROVED
P
C4425-C02- C
MASS
kg
TAKAHASHI. T
E. MIYOSHI
送受波器 TRANSDUCER
520-5PSD 520-5MSD 520-5PWD
WHT
シロ
クロ
BLK
5 2 1 4 3
MB-1000
1 2 3
02S4092-0,8m
525ST-PWD 525ST-MSD
10m (1kW) 50/200-1T
NAME
名称
TITLE
INTERCONNECTION DIAGRAM
GPS/DGPS PLOTTER/SOUNDER
相互結線図
GP-1850WF/1850WDF GPS/DGPSプロッタ魚探
RD RS-232C NMEA0183 in RS232C LEVEL *4 SHIELD
T-02MTB T-02MSB ST-02MSB T-03MSB ST-02PSB 水温・船速ｾﾝｻｰ TEMP/SPEED SENSOR
アカ RED アオ BLU
MJ-A10SPFD 水温・船速ｾﾝｻｰ付送受波器 TRANSDUCER W/ TEMP/SPEED SENSOR
MJ-A6SPFD
P
NMEA0183 Ver 2.0/1.5
4
DGPSビーコン受信機 DGPS BEACON RECEIVER
MJ-A6SPF0007,10m MJ-A6SPF0012,5/10m MJ-A6SPF0011,5/10m MJ-A6SPF003,5m,φ6 シロ WHT クロ BLK キ YEL ミド GRN
MJ-A7SPF0003,5m キ YEL SD
*3 MJ-A7SPFD
P
P
*3 MJ-A6SPF
DRAWN Aug. 24, '04 CHECKED
GND *1 IV-1.25SQ.
XDR J2 SPD 12V-P GND TEMP NC NC GND XDR-P XDR-SHIELD XDR-M
1 2 3 4 5 6
SPD/TEMP J9 SHIELD TEMP TEMP0V/SPD SPD +12V NC
1 2 3 4 5 6
1 2 3 4 5 6 7
NMEA J6 TD-A TD-B RD-H RD-C NC SHIELD
DGPS J5 NC NC RD NC RS-232C SD NMEA0183 Ver1.5/2.0 SG RTCM104 SHIELD
12-24 VDC J3
(+) (-) SHIELD
J7
ANT
指示器 DISPLAY UNIT GP-1850WF/WDF
注記 ＊１）現地手配。 ＊２）オプション。 ＊３）コネクタは工場にて取付済み。 ＊４）カレントループ、RS-422の接続にはオプションのレベル変換器が必要。
100/110(115)/ 220/230VAC, 50/60Hz,1φ
*2 TNC-P-3 *3 5A MJ-A3SPFD
N-P-8DFB N-J-3 *2 *3 NJTP-3DXV-1 1m,φ5.3
MJ-A3SPF0013,3.5m,φ8.0 シロ WHT クロ BLK
8D-FB-CV *2 30/50m
TNC-PS-3D,15m,φ5.3
12-24 VDC
*3 TNC-J-3
GPA-017(GP-1850WF) GPA-019(GP-1850WDF)
*2 *3 NJTP-3DXV-1 1m,φ5.3
GPA-017S(GP-1850WF) GPA-019S(GP-1850WDF)
TNC-P-3
TNC-P-3
*3 TNC-J-3
空中線部 ANTENNA UNIT
10m,φ5.3
N-J-3 *3 N-P-8DFB
3
TB1
BLK
2
GRN
TB2
アカ RED クロ
1
ミド BLU アオ
