In order to purchase this package click on the link below: http://www.cdrdownload.com/electrical/
Package Contents:
Career Episode One, Career Episode Two, Career Episode 3, CPD, Resume, Summary Statement
Project: Electronic Engineering Category: Professional Engineer ANSZCO Code: 2334 Assessment Result: Successfully Assessed in January 2016
Career Episode One: CDR-EL-1100-1 Role: Electronic Engineer Engineer’s Responsibilities:
•
Detecting the problem and providing the solution
•
Revising the schematics diagrams and issuing the revised set
•
Creating PCB schematics of the x product.
•
Observing the safety and environmental requirements in my design
•
Writing reports detailing current situation and changes to each site
•
Performing regular calibration and adjustment
•
Refill the tube CO2 gas whenever the system s ystem shows low gas alarm
•
Train junior technicians
1
•
Liaise with customers after install or repair r epair the get feedback
•
Develop new procedures to test and repair systems
Key Words: electronic engineer, drafts person, Sony company, QC certification, PCB boards, schematic diagrams, customer support, Electrical Design, Software Design and Simulation, PCB Design, Calibration, Safety, Repair, Safety, Protel Software, Engineering Standards, Electronics, Laboratory tasks, PCB Design & Layout, Quality Control Standard, PCB testing and troubleshooting, Training new technicians Word Count: 4 pages – 1488 words
Career Episode Two: CDR-EL-1100-2 Role: Electronic Engineer Engineer’s Responsibilities:
•
Attending the training courses in calibration procedures, fault finding and rectification of the fault with the system Automation
•
Calibrating all the equipment for the operation
•
Verifying the aircraft types to each system memory as per requirements of particular stand type
•
Testing the operation of VDGS in the correct detecting aircrafts and stopping them at the correct stop position
•
Installing the Gate Operating System (GOS) at the tower for f or the Air Traffic Controllers (ATC) in order to use and train them for the proper use of the system
•
Ensuring all the designs were within the budget constraints
•
Observing HSE factors in my work
2
•
Reporting the project progress to the project manager
Word Count: 5 pages – 1800 words Key Words: Lasers, Automated Guided Systems, VDGS System, Gate Operating System, Automated Guiding, Air Crafts, Stepper Motors, HSE and Safety regulations, Air traffic controllers, control systems, Peltier drivers water, Management skills, AFL System Engineer
Career Episode Three: CDR-EL-1100-3
Role: Electronic Engineer Engineer’s Responsibilities:
•
Technical control in preparation of the Electrical engineering documents and their finalization before procurement and construction phases.
•
I mainly worked as Electrical document’s supervisor/Producer/Reproducer.
•
Providing solution to critical issues during the meetings. I was responsible to prevent any project delay due to technical technical issues pertinent to Electrical Electrical Engineering field.
•
Reviewing and providing solution for problems involved. I had to review the project aspects multiple multiple times during the project project progress, taking into into account the cost, safety, the economic aspects along with other necessary requirements
•
Analyzing the project and predicting the possible problems and providing plans for bypassing them. them.
•
Observing the business factors relevant to my scope of work.
•
Finding the new and updated solutions though research, making sure that the final project is according to new standards is well equipped for long run.
3
•
Design and preparing drawings for the parts which did not have drawing during design phase and also compensating shortage of documents
•
Supervision on standards applications during the project execution
•
Supervising pipe jacking operation, design and conducting guard structures in order to increase safety levels of construction
Key Words: Floating tanks, fixed roof tanks, gas and oil, fuel, f uel, storage tanks, loading arms, steam boilers, technical control of engineering documents, EPC, safety, economic aspects, research, Deliverable list, Data Sheets, lights, UPS, Distribution Control Systems (DCS), Fire and Gas Systems, PLC panels, Cable sizing, Material requisition, 33KV to 6Kw electromotor, Transformers, Distribution Matrix, Engineering Standards, Software Design and Dialux, Electrical Auto CAD, ETAP, Project expense reduction Document & Word Count: 11 pages – 2000 words
Resume: CDR-EL-1100-4 Package Content: Word Format of the Resume ready to be Modified based on
your own Resume, and Expertise. You only need to copy paste your qualifications in the format attached. This Resume is chronological order which is required by Engineering Australia. Document: 2 pages – 483 words
CPD: CDR-EL-1100-5 Package Content: Once Sheet Word Format CPD with all the Qualifications, and
4
Requirements Document & Word Count: 1 page – 220 words
Summary Statement: CDR-EL-1100-6
Package Content: Six Pages of the competency demonstration reports that totally
matches all three career episodes’ qualifications. Document & Word Count: 6 pages – 1553 words
5
