Which 12- or 24-port Fibre Channel switch from HPE is designed and recommended for use in hyper- scale, private cloud storage, and highly virtualized environments, environments, and supports the “payas-you-grow” model?
HPE StoreFabric SN3000B switch
HPE StoreFabric 8/24 switch
HPE StoreFabric SN6500B switch
HPE StoreFabric SN6000B switch
Which optional, licensed HPE B-Series SAN switch capability enables each switch to m onitor a variety of SAN fabric elements for potential faults and automatically alerts the network administrator of problems before they become failures?
Fabric Watch
Fabric Vision
SAN Network Advisor
Advanced Performance Monitor
Which HPE C-Series enterprise package license feature enables selective transfer of data traffic between specific initiators and targets on different virtual SANs without merging them into a single logical fabric?
Adaptive Networking (AN)
Inter-VSAN Routing (IVR)
Enhanced Group Management (EGM)
Extended VSAN Fabric (EVF)
When are read-only zones, supported by the HPE C-Series SAN switches, useful?
when locking down the mapping mapping of an entity to a switch port ???
when using SCSI commands commands as zoning zoning attributes ???
when configuring switch-switch and HostSwitch H ostSwitch authentication
when implementing security with inter-VSAN routing
Match each HPE B-Series Fibre Channel switch to its intended target environment. (Drag each item in the right column to the corresponding item in the left column. Let the cursor hover over an item to see its full text.) HPE SN3000B switch low-cost, pay-as-you-grow, hyper-scale, ... HPE 8/24 SAN switch small-to-medium businesses, entry-level ... HPE SN6500B switch hyper-scale, privatecloud storage, and ... HPE 8/8 SAN switch a standalone core switch or a lower-cost...
Which statements correctly describe the HPE SN6000 Fibre Channel Switch? (Select two.)
Its single-power models are upgradable to dual power.
It has four (4) dedicated stacking links.
It requires the Enterprise Fabric Management Management Suite (EFMS) software.
It starts as a 24-port switch and is expandable to 48 ports within a single switch device.
It comes in a 1U form factor.
Which HPE-supported switches are designed to fit into the interconnect bays of the HPE BladeSystem c-Class enclosure? (Select two.)
Cisco MDS 9222i Multiservice Modular Fabric Switch
HPE Encryption SAN Switch
HPE 6Gb SAS Switch
Brocade 16Gb SAN Switch
HPE 8/20q Fibre Channel Switch
Which command upgrades the HPE B-Series SAN switch Fabric OS (FOS) using CLI and FTP?
firmwareupdate
firmwareupload
firmwaredownload
firmwareflash
What is the out-of-the-factory default username and password for the HPE B-Series SAN switches?
username = hpe, password = hpe
username = admin, password = password
username = admin, password =
username = , password = administrator
What happens when you attempt to access Web Tools using the http://{switch IP address} address from a system that does not have a supported Java Runtime Environment (JRE) installed?
A message displays asking you to use the secure address instead.
A “page not found” message displays.
You are redirected to the compatibility matrix support page for Web Tools.
A message displays asking you to download a supported version of JRE.
You installed Web Tools to manage basic zoning and traffic isolation zoning in your SAN environment. Now, you want to perform advanced tasks such as clone operations for zoning. Which type of license must you install on the 8Gb or 16Gb HPE B-Series SAN switches?
APM license
EGM license
Power Pack + license
SAN Enterprise license What automates multi-switch configuration operations across enabled Brocade SAN switches to save time and streamline repetitive operations?
EGM
LSAN zoning
APM
QoS zoning
You need to manage a large SAN that comprises of approximately 100 fabrics. Which tool would enable you to do so?
HPE SANXpert with Fabric Vision
HPE SAN Network Advisor Enterprise
HPE SAN Network Advisor Professional Plus
HPE Web Tools with the EGM license
What is the default zoning setting of the HPE C-Series SAN switches?
no access
local access
all access
peer access 120 device -> no access
Which Fabric OS zoning enforcement validates only the ELS frames that were used to establish a session?
session-based software enforcement
session-based hardware enforcement
domain-based zone enforcement
frame-based hardware enforcement
???
You need to completely reset the zoning configuration definitions on your Brocade B-Series SAN switches. Which other commands must be used in conjunction with the cfgClear command to save the cleared SDRAM into flash and clear everything on the switch? (Select two.)
cfgSave
cfgDisable
cfgPurge
cfgReset
cfgDelete
cfgCreate
You need to reset your HPE B-Series SAN switch to the HPE default settings. What must you do?
Call the HPE support center and obtain a specific set of instructions from the support personnel.
Download the latest firmware file from HPE and use the firmwareDownload command.
Use the configDownload command with a downloaded HPE default configuration file.
Use the configDefault command to reset the SAN switch configuration.
You are using Web Tools to manage your Brocade SAN switches and want to perform advanced SAN operations such as cloning of zone configurations. However, your access to this feature is denied and an error message displays. Why does this occur?
Web Tools are not licensed with the EGM license.
Web Tools are not licensed with the APM license.
You have not logged in with super user privileges.
You have not logged in with administrative privileges.
Which SAN tool is represented by this picture?
Web Tools
Intelligent Infrastructure Analyzer software
SANXpert
SANtelligence
You are using Web Tools to manage your Brocade SAN switches. What must you do to enable users to make zoning changes offline without affecting the production fabric?
apply the APM license to Web Tools
use the Fabric Vision feature within SANXpert
use the SAN Network Advisor
apply the EGM license to Web Tools
Which zoning statements are correct? (Select three.)
Devices may be members of more than one zone.
Zoning provides security.
If a device is not a member of a zone, it is not accessible by any device within that zone.
Devices may belong to only one zone.
The number of zones and zone members are limited by the sum of switch ports in the fabric.
What is the default zoning setting of the HPE H-Series SAN switches?
no access
local access
peer access
all access What happens when you merge two fabrics, where one fabric is zoned and the other fabric is unzoned but set to “no access?”
The fabrics merge, but no access is given.
The zoned fabric’s configuration propagates to the unzoned fabric.
The fabrics merge cleanly.
The fabrics end up segmenting.
What is the purpose of traffic isolation zoning?
It allows devices on separate Fibre Channel fabrics to communicate with each other.
It allows control of traffic flow between switches using dedicated paths.
It allows SAN design and management to be done at the port granularity.
It provides selective device connectivity between fabrics without merging them.
Which SAN fabric concept do the dashed circles in this picture represent?
Virtual Fabrics
FC-FC routing
traffic isolation zoning
LSAN zoning
You are configuring an HPE 3PAR Smart SAN. Your configuration consists of:
a single 48-port switch 40 initiators 4 target ports 4 groups of 10 initiators associated with each target port
How many zones do you need to create for initiator-based zoning?
40
4
48
16
Which type of communication is allowed with an HPE 3PAR Smart SAN peer zone?
Non-principal members can only communicate with other non-principal members.
Non-principal members cannot communicate with principal members.
Principal members can communicate with any non-principal member.
Principal members can communicate with other principal members only.
Which term refers to transmitting multiplexed traffic from several devices across a single ISL for the reasons of optimizing the switch utilization?
undersubscription
thin provisioning
storage convergence
auto-provisioning
oversubscription
You are looking for interswitch link limitations, fabric rules, and tables applicable to HPE B-Series SAN switches. Which resource would have this information?
HPE ActiveAnswers
SAN Design and Best Practices document from Brocade
HPE SAN Design Reference Guide
HPE IT Resource Center
What does the following HPE B-Series SAN switch command accomplish? portcfgtrunkport 4,1
It adds port 4 to the trunking configuration 1.
It disables the trunking configuration for port 4.
It enables the trunking configuration for port 4.
It enters the trunking configuration menu for ports 1 and 4.
What must you do to successfully configure ICLs in a fabric that consists of HPE SN8000B 8-Slot SAN Backbone Director switches?
You must be running Fabric OS 5.0.1 or later.
You must install the ICL optical cables before installing the enterprise ICL licenses.
You must install an enterprise ICL license on each Director switch.
You must have two unused ports in each Director switch. If trunking is not enabled on a C-Series port channel, how many VSANs can use this port channel?
four
one
two
none
What is true of adaptive trunking and stacking with the HPE H-Series switches?
Adaptive trunking does not require a license.
Stacking on the HPE SN6000 switch requires two unused 2Gb/4Gb/8Gb switch ports.
Adaptive trunking balances frames across multiple paths between two or more switches.
Stacking supports up to 8 switches per stack.
What is the correct definition of HPE B-Series virtual fabrics?
They allow devices in different fabrics to communicate with each other without having to merge the fabrics.
They allow the administrator to divide a physical chassis into multiple fabric elements called logical switches.
They allow the administrator to manage multiple non-merged fabrics using federated management tools.
They allow creation of dedicated communication paths between switches to segregate the traffic.
Which statements correctly describe the creation and operation of VSANs on HPE C-Series SAN switches? (Select two.)
By default, all switch ports belong to the default VSAN0.
When a port is removed from a VSAN, it is moved to the default VSAN0.
Each HPE C-Series SAN switch supports 128 VSANs.
Each VSAN has its own fabric services, which cannot communicate by default with devices in other VSANs.
Traffic disruptions are isolated and have no impact on other VSANs.
Which statements correctly describe a routed fabric and routed fabric services? (Select two.)
Each fabric maintains a unique fabric services configuration.
A router in a Meta SAN provides any-to-any connectivity between fabrics.
Routing connects devices in multiple fabrics without extending fabric services from one routed fabric to another.
A disruption of fabric services in one routed fabric typically affects the entire Meta SAN.
Which term refers to an HPE B-Series routing configuration, similar to a Fibre Channel zone, where shared devices in different fabrics are identified and replicated so that they can communicate across these distinct fabrics?
IFR
VSAN
FSPF
LSAN
Which optional, licensed HPE C-Series SAN switch feature enables you to configure devices in one VSAN to access devices in another VSAN?
IFR
FSPF
IRF
IVR
What would enable you to implement transparent routing to a remote fabric containing C-Series devices?
DC Director switch
MPX200 multi-function router
H-Series switch
1606 Extension SAN switch
You are troubleshooting connectivity issues within an HPE B-Series SAN fabric. What in the portErrShow output indicates that the problem is likely caused by a bad or damaged cable or a faulty device in the path?
non-zero value for loss of synchronization (loss sync)
increasing number of class 3 frames being discarded (disc 3)
increasing number of encoding errors outside of frames (enc_out)
non-zero value for loss of signal (loss sig)
After you determine that a host cannot connect to a storage device, which command should you run first to determine whether the storage device is connected to and logged into the switch?
uRouteShow
switchConfig
switchShow
portLogShow
You are troubleshooting an HPE 3PAR Smart SAN installation. What does the portcfgshow command, issued from the HPE B-Series SAN switch, enable you to determine?
whether the SAN switch is running a supported version of the FOS
what the FDMI database contents are
whether the peer zones are recognized by the fabric
whether the target driven peer zoning is enabled
Which command resets the non-persistent configuration data of the HPE B-Series switches back to their factory-default settings (not the HPE default settings)?
factoryReset
configDefault
switchReset
switchDefault Which statement is true about the basic (free-of-charge) management capabilities of the HPE BSeries SAN Network Advisor?
It provides QoS, ingress rate limits, and traffic isolation zones.
It can manage up to 10 FOS fabrics.
It can manage up to 300 switch ports.
It supports B-series DC SAN Backbone Director and SN8000B 8-Slot SAN Director devices.
Which command moves one or more members out of an existing zone?
zoneDelete
zoneClear
zoneRemove
zoneReconfigure
Which Fabric OS command displays the enforced zone type?
getZoneType
zoneTypeShow
portZoneShow
zoneDisplay
Which type of HPE 3PAR Smart SAN zoning is configured with these three steps? 1. Select the initiator and identify the pWWN. 2. Create the host using the 3PAR CLI and identify the N:S:P that the host will be accessing. 3. Repeat for each initiator. 4. dynamic zoning
initiator-based zoning
target-based zoning
initiator-suppressed zoning
Match each Fibre Channel routing term with its correct definition. (Drag each item in the right column to the corresponding item in the left column. Let the cursor hover over an item to see its full text.) virtual fabric a chain of switches from a source switch... path a collection of ports from a set of conn... route a dynamically assigned path that a devic... hop a point-to-point link (an interswitch link)
Which HPE B-Series SAN switch command enables or disables trunking on all ports in the switch?
switchport trunk enable | disable
switchCfgTrunk
trunkEnable | trunkDisable
portCfgTrunkport
You need to determine the size of the fabric and all devices within the fabric. W hich command would give you this information?
nsShow
nsAllShow
cfgShow
fabricShow
You are investigating whether a device is in the active zone configuration with another device. Which command would give you this information?
cfgShow
nsShow
switchShow
zoneShow
What happens when you merge two fabrics, but only one of them is zoned?
The fabrics merge, but no access is given.
The fabrics end up segmenting.
The zoned fabric’s configuration propagates to the unzoned fabric.
The fabrics do not merge and display an error message.
Review the picture below.
You are configuring an HPE 3PAR Smart SAN. Your configuration consists of:
a single 48-port switch 40 initiators 4 target ports 4 groups of 10 initiators associated with each target port
How many zones do you need to create for target-based zoning?
48
40
16
4 Which statements correctly describe the creation and management of logical switches? (Select two.)
The default logical switch can only be deleted if you disable the virtual fabrics feature.
When the virtual fabrics feature is enabled, a default logical switch is created, containing all switch ports.
The default logical switch is assigned Fabric ID of 255.
When the virtual fabrics feature is enabled, ISLs are no longer supported.
What do HPE B-Series Virtual Fabrics use to share devices across logical fabrics? (Select two.)
inter-VSAN routing (IVR)
inter-fabric links (IFLs)
fabric shortest path first (FSPF)
inter-fabric routing (IFR)
intelligent resilient forwarding (IRF)
While upgrading the HPE B-Series SAN switch firmware, you notice that the network has become unreliable. Furthermore, the firmwareCommit command did not complete successfully. What is the recommended action you should take?
Roll back the firmware to the previous known version, download the new firmware again, and repeat the firmware flash procedure.
Wait 15 minutes, execute firmwareShow to retrieve the firmware versions, and reissue firmwareCommit if the versions are different on both partitions.
Reset the switch to factory default settings, download the new firmware again, and repeat the firmware flash procedure.
Press the switch reset button for at least 5 seconds or until the switch reboots.
Where do you obtain the Boot PROM recovery password for the HPE B-Series SAN switches?
from the switch support provider
from the output of the recover password menu option
from the toe-tag shipped with every switch
from the output of the switchCfg command
69.43%
